Document No. HIMURJA (F-7) / SPV Plant / RTS /

Transcription

1 Document No. HIMURJA (F-7) / SPV Plant / RTS / RATE CONTRACT (Under Empanelment Scheme) Design, manufacture, supply, erection, testing and Commissioning including warranty, operation & maintenance for 5 years of 1 kwp to 500 kwp Grid connected Rooftop Solar Power Plants under the Grid Interactive Rooftop Solar Power Plants scheme of MNRE and the Solar Power Policy in the State of Himachal Pradesh to be installed on the roofs of Govt. buildings of different capacities (having an aggregate capacity of 2.5 MWp in Shimla city & 2 MW all over state) & for Domestic, Institution (registered under society/trust act) and Social Sector buildings in the State. HIMURJA H.P. Govt. Energy Development Agency 8-A,SDA Complex, Kasumpti, Shimla Himachal Pradesh, INDIA Telephone No: Fax No: Website:- Himurja.nic.in

2 Rate contract for Grid interactive rooftop Solar PV Power Plant A. NECESITY FOR THE RATE CONTRACT Ministry of New and Renewable Energy, Govt of India is promoting Grid connected Rooftop Solar Power plants in the country and sanction has been accorded by the Ministry for installing GCRTS in the State. To achieve the Targets fixed for H.P. State, HIMURJA will empanel firms for the Design, manufacture, supply, erection, testing and commissioning including warranty, operation & maintenance for 5 years of Rooftop Solar Power plant of capacities varying from 1 kwp to 500 kwp in the State of Himachal Pradesh. MNRE, GoI has revised the benchmark cost for the year accordingly tender is floated for rate contract to the Registered Firms for the supply, installation and commissioning of Grid connected Rooftop Solar Power Plants to be installed on the roofs of Govt. buildings of different capacities (capacity of 2.5 MWp in Shimla city & 2 MW all over the State) and Domestic, Institution (registered under society/trust act) and Social Sector buildings in the State. B. SUBSIDY PATERN: i) Capital subsidy upto maximum 70% of the benchmark cost of the system as per the latest notification of MNRE is available for all rooftops of Domestic, Institution (registered under society/trust act) and Social Sector buildings in the State. Apart from this a State subsidy of Rs 4000=00 per kwp is available for these buildings. ii) For Government buildings / Institutions the subsidy is progress linked and will be almost 60% in case the scheme is completed within the stipulated period, failing which liable to be reduced in percentage as per MNRE, GoI, norms. C. SCOPE OF WORK: HIMURJA invites bids for rate contract for design, manufacture, supply, erection, testing and commissioning including warranty, operation & maintenance for 5 years of Grid Interactive Rooftop Solar Power Plants of capacities varying from 1 kwp to 500 kwp in the State of Himachal Pradesh, to be installed on the roofs of Govt. buildings of different capacities (capacity of 2.5 MWp in Shimla city & 2 MW all over the State) & also for rate contract for installation of

3 Rooftop Solar Plants at domestic/institution (registered under society/trust act)/social sector buildings under empanelment scheme in the State; from the experienced Solar Power plant EPC contractor, Manufacturer of Solar modules or Inverter. The tender document can be purchased from the office of Himurja at Shimla by paying Rs. 10,000/- only in the shape of demand draft drawn in favour of Director, HIMURJA, Shimla from to The tender document shall be received/ submitted up to Hours on dated and will be opened on the same day at 3 PM in the presence of the bidders or their authorized representatives who may like to be present. The bid documents can also be downloaded from the website of HIMURJA i.e. himurja.nic.in. The cost of the documents in that case can be deposited along with the bid in the shape of demand draft in favour of Director, HIMURJA, Shimla separately. The rates will be applicable to all the Firms empanelled with HIMURJA who wish to provide their services on the lowest quoted prices which are received under this offer. The selected firms will have the opportunity to execute the projects for which the sites can be identified by the firms or on the sites allocated by HIMURJA under the Grid Interactive Roof top Solar Power Plants in accordance with technical specifications and various other requirements as per latest directions / guidelines of MNRE, GoI under NSM. The various group of size / capacity of the grid interactive rooftop solar power plant shall be as under: S.No. Group of Size/capacity Location 1. Upto 10 kwp 2 >10 kwp to 50 kwp 3 >50 kwp to 100 kwp Anywhere in the state of Himachal Pradesh 4 >100 kwp to 300 kwp 5 >300 kwp to 500 kwp HIMURJA will provide the applicable CFA to the registered firms based on the lowest rates received under this tender and subject to the release of funds by Ministry, GOI. The empanelled firms will design, manufacture, supply, erect, test and commission and make all necessary arrangement for evacuation and injection of surplus power to the HPSEBL grid at the interconnection point.

4 D. SITE / PROJECT LOCATION It is important to note that under the Grid Interactive Roof Top Solar Power Plants Scheme the projects of various capacities from 1 kwp to 500 kwp can be allotted depending upon the sites identified. The firms can also be given specific targets so as to implement the programme in a time bound manner. The firms will also be at liberty to identify buildings or find potential beneficiaries to achieve the allotted targets. HIMURJA will also from time to time identify buildings / beneficiaries which will be made known to the empanelled firms. D. INFORMATION TO THE FIRM / BIDDER 1. Earnest Money / Security Amount:- 1.1 Bid accompanied by earnest money/ bid security of Rs. 1,00,000=00( Rupees One Lac only) through demand draft only shall be accepted. 1.2 The earnest money / bid security is required to protect the HIMURJA against risk of Bidder's conduct which would warrant the security's forfeiture. No interest will be paid on Earnest Money. 1.3 Unsuccessful Bidder's earnest money / bid security will be discharged / returned as promptly possible as but not later than thirty (30) days after the expiration of the period of bid validity prescribed by the HIMURJA subject to receipt of request letter from the bidder. 1.5 The bid security may be forfeited: a) If a Bidder withdraws its bid during the period of bid validity specified by the Bidder on the Bid Form. b) In case successful Bidder fails to sign the Contract or to furnish required performance security. 1.6 The Earnest Money/Security Amount of the empanelled firms will be refunded after the completion of duration of empanelment. 2. Duration of Empanelment 2.1 The selected firms / bidders will be empanelled initially for a period of one year. After completion of this period, the validity of rates may further be extended on the basis of performance of the consultant firm and mutual consent between HIMURJA and interested empanelled firms. 2.2 The firms will be registered within one month from the date of finalization of lowest rates.

5 3. Payments Empanelled firms will have to supply and install the Solar Power Plants on the rates approved by HIMURJA in each group and will get payment as under: % of the CFA as applicable, due from MNRE, shall be paid after successful installation, commissioning of the Solar PV Power Plant and injection of surplus power (if any) into the HPSEBL grid confirming to technical specifications as specified in this tender. The CFA will be given as per the prescribed MNRE benchmark cost from time to time. 3.2 The amount due from the beneficiary (30% of the total cost) will be taken by the firm directly in case the beneficiary has been identified by them and in case the beneficiary has been selected by HIMURJA the amount will be paid by HIMURJA immediately after installation and commissioning of Solar PV Power Plant. In case of GCRT plant installed on Govt buildings no beneficiary share has to be taken and the full payment will be made by HIMURJA. 3.3 Balance 10% of the CFA shall be treated as performance security and shall be paid against satisfactory performance of the Solar PV Power Plant during warrantee, operation and maintenance period. This amount shall be paid to firm after completion of five year from the date of Commissioning at site. The bidder shall have to submit performance & functionality report to HIMURJA for the release of this payments duly verified by the concerned Project Officer HIMURJA. 3.4 The firms will have to supply & install the Rooftop Solar Plant at the site of beneficiaries within 60 days of receipt of funds from the beneficiary, failing which the liquidated damages shall be 1 % per week, 5% of the contract price 1% for delay of 1 2% for delay of two 3% for delay of three 4% for delay of four week 5% for delay of five week and will be recovered from any sums due to the firm. 4. Eligibility criteria 4.1 The Bidder should have sufficient funds and technical expertise for the installation of Grid connected Rooftop Plants in the State. 4.2 The Bidder should have a Service centre in the State for carrying out repair and maintenance of the Plant. The details of the service centre is to be mentioned in the bid. 5. Clarification of Bids 5.1 During evaluation of the bids, the HIMURJA may, at its discretion, ask the Bidder for a clarification of its bid. The request for clarification and the response shall be in writing, and no change in the prices or substance of the bid shall be sought, offered, or permitted.

6 If the firm does not respond to the clarification, the firm will be considered as nonresponsive and the bid shall be rejected out rightly. 5.2 At any time prior to the submission of the bid or prior to the opening of the financial bid HIMURJA may for any reason whether at its own initiative or in response to a clarification requested by the bidders may modify the bid document by amendments. The amendment will be notified in writing or by fax to all prospective bidders who have received the bid documents and will be binding on them. HIMURJA will bear no responsibility or liability arising out of non receipt of the same in time or otherwise. 6. Evaluation and Comparison of Bids 6.1 HIMURJA will evaluate and compare bids which have been determined to be substantially responsive. 6.2 The detailed techno-commercial analysis of the bid shall be carried out by the HIMURJA. 7. HIMURJA's Right to Accept Any Bid and to Reject Any or All Bids 7.1 The HIMURJA reserves the right to accept or reject any bid, and to cancel the bidding process and reject all bids at any time prior to award of Contract, without thereby incurring any liability to the affected Bidder or Bidders or any obligation to inform the affected Bidder or Bidders. 8. Opening of Technical Bids by HIMURJA 8.1 The HIMURJA will open the technical bids, in the presence of Bidders' representatives who want to be present, at the time, on the date, and at the place specified in the Bid Data Sheet. The bidder s representatives present during the opening of the bid, shall sign a register evidencing their attendance. 8.2 The Bidders' names, the presence or absence of the requisite bid security and such other details as the HIMURJA, at its discretion, may consider appropriate will be announced at the opening, except for late bids, which shall be returned unopened to the Bidder. 8.3 The technical bids shall be evaluated by the HIMURJA for assessing responsiveness, bidders qualification and technical confirmation. 8.4 The bidders whose technical bids are declared as technically responsive and qualified shall be informed accordingly and their Price Bids shall be opened. 8.5 The bidders whose technical bids do not qualify, their Price Bids shall not be opened and the same shall be returned to the Bidders. Moreover, such bidders shall not be empanelled at lowest cost in future.

7 8.6 Price Bids opening date shall be conveyed subsequently. 9. Signing of Contract The successful Bidder will sign the contract within thirty (30) days from the date of issue empanelment letter. 10 Selection of bidder(s) for empanelment i. The lowest quoted rates by any bidder for every group of size / capacity will be taken as a base rate. ii. HIMURJA will empanel the technically qualified bidders who agree to work on the lowest quoted rates (base rate) in each group of size / capacity of the project. iii. The list of the successful empanelled bidder / firm will be placed on the website of HIMURJA for the information of the beneficiaries.

8 TECHNICAL SPECIFICATION Technical specifications of the Grid Interactive Rooftop Solar Power plant shall be in accordance to the latest MNRE, GoI technical specifications as issued vide notification no.30/11/ /nsm dated 26/06/14 or as directed by MNRE, GoI for the grid interactive rooftop and small SPV power plant from time to time. 1 Brief Description of the System The main components of the SPV plant are PV Modules Civil Work. Module Mounting Structure Array Junction Boxes String Monitoring Boxes Grid Tie Inverters Solar Meter Step- up Transformer LT Step- up Transformer HT SCADA / Monitoring System as per predefined parameters for higher capacity plants Earth System Lightning & Surge Protection DC Cables. AC Cables. Illumination System AC Metering and Grid Interconnection System. This list is of general nature and some of the components may not be required or may be combined as per the system finally designed. 2. Typical Power Generation Scheme The system consists mainly of the following: Solar PV array which produces DC electricity when solar rays incident on it Power Conditioning Units (PCU) or Inverters which convert DC (Direct Current) electricity into AC (Alternating Current) electricity and facilitate synchronization with the grid power and has all the required protections as mentioned in the Net Metering Regulations. The copy of the Net Metering Regulations is available on the website of Himurja i.e.

9 Transformers which transform the AC output of the Power Conditioning Units to the level required at the grid The SPV array (constituting solar PV modules of selected rating connected in series and parallel combinations to build up the Voltage and Current parameters as per desired design modalities ) produces DC electricity when Solar insolation is incident on it. The DC power thus produced is taken through various junction boxes and isolators and connected to the Inverter. The Inverter houses the inverter circuitry which converts DC power supply into AC power supply, the synchronization circuitry which actualizes the tie-up of solar PV source to the grid source and the remote monitoring and control circuitry. A number of Inverters are connected in parallel as per the desired AC Power required. Depending on the grid voltage level to which the solar PV power is being synchronized, different levels of step-up transformers may have to be deployed. The protection and metering circuits play a very significant role in the Inverter operation. Appropriate current transformers and potential transformers are used to tap required feed back signals to initiate action on metering and protection. 3 Typical System Components a. PV MODULES: i. The PV modules must conform to the latest edition of any of the following IEC /equivalent BIS Standards for PV module design qualification and type approval: Crystalline Silicon Terrestrial PV Modules IEC / IS14286, Thin Film Terrestrial PV Modules IEC61646 / Equivalent IS (Under Dev.), Concentrator PV Modules & Assemblies IEC ii. In addition, the modules must conform to IEC61730 Part 1-requirements for construction & Part 2 requirements for testing, for safety qualification or Equivalent IS (Under Dev.) iii. PV modules to be used in a highly corrosive atmosphere (coastal areas, etc.) must qualify Salt Mist Corrosion Testing as per IEC 61701/ IS Authorized Test Centers: The PV modules must be tested and approved by one of the IEC authorized test centers. In addition a PV module qualification test certificate as per IEC standard, issued by ETDC (Electronics Test & Development Centre), Bangalore or Solar Energy Centre will also be valid. Identification and traceability: Each PV module used in any solar power project must use a RF identification tag. The following information must be mentioned in the RFID used on each module. (This can be inside or outside the laminate, but must be able to withstand harsh environmental conditions.)

10 Name of the manufacturer of PV Module Name of the Manufacturer of Solar cells Month and year of the manufacture ( separately for solar cells and module) Country of origin ( separately for solar cells and module) I-V curve for the module Wattage, Im, Vm and FF for the module Unique Serial No and Model No of the module Date and year of obtaining IEC PV module qualification certificate Name of the test lab issuing IEC certificate Other relevant information on traceability of solar cells and module as per ISO 9000 WARRANTY: PV modules used in solar power plants /systems must be warranted for their output peak watt capacity, which should not be less than 90% at the end of 12 years and 80% at the end of 25 years. b. BALANCE OF SYSTEM (BOS) ITEMS/ COMPONENTS: i. Module Mounting System The mounting structure shall be designed for holding suitable number of modules in a series. The frames and leg assemblies of the array structures shall be made of mild steel hot dip galvanized of suitable sections of angle, channel or any other section confirming to IS Stainless Steel /Hot dip galvanized steel nuts and bolts will be used. The structure shall be designed to withstand all loads incl. wind etc. The mounting structure shall be designed in such a way that it will occupy minimum space without sacrificing the output from SPV modules. Specially designed Aluminum Structures may also be offered for better protection against the Corrosion over the life of the Plant. While making Civil & Mechanical design, due consideration will be given to all the dead loads, live loads, effects of wind loads, Seismic factors for the site and suitable Design margins as per prevalent Indian standard and Industry practices. The Mechanical components for the module mounting shall comply to standards to withstand wind loads of 150 Kmph and suitable design and test reports should be made available on demand. ii. Power Conditioning Unit The type of technology selected shall be suitable for the specific project location considering the PV Solar Modules selected so as to maximize the yield over the plant life. The inverter selected shall be either Distributed type or the Central type. The capacity and the number of the inverters selected shall be optimized so as to have less number of inverters however without compromising the redundancy in case of failure of the inverter. The inverters shall have

11 a Built in transformer. In case the inverter model selected is transformer-less, then the external transformers shall be provided to achieve the desired level of voltage for the evacuation system. The Offered Inverter should have internationally recognized IEC, TUV and/or UL certifications (or equivalent as approved). Manufacturer shall carry out all the tests as per the requirements of IEC, TUV and UL as applicable. Supplier shall submit all the Manufacturing Test Certificates, performance test certificates Inspection test Reports etc. in addition all the technical specification sheets, product catalogues, Installation manuals, Operation and maintenance manuals etc. in adequate numbers as finalized. General description of Inverters The DC power produced by Solar Modules is fed to inverter for conversion into AC. In a grid interactive system AC power has to be fed at 415V 3Ph 50 Hz. The output of the inverter must synchronize automatically its AC output to the exact AC voltage and frequency of the grid. The design of the inverter should be made to meet the Indian voltage and frequency conditions (the frequency band should be ±5%). The inverter continuously monitors the condition of the grid and in event of grid failure; the inverter automatically isolates the Solar Power System. The solar system is resynchronized with the grid after the restoration of grid. The inverter shall be designed so as to operate the PV system near its Maximum Power Point available, the operating point where the combined values of the current and voltage of the solar modules result in a maximum power output. The inverter should be a true sine wave inverter for a grid interactive PV system. The degree of protection of the indoor inverter panel shall be at least IP-31 and that of outdoor at least IP-55. In Addition the PCU must qualify the following IEC/equivalent BIS standards/mnre specifications/as specified below: BOS Item/ system Power Conditioning Unit/ Inverter** including MPPT and Protections (more than 100 Wp and upto 20 kwp capacity only) Applicable BIS / Equipment IEC Standard or MNRE Specifications Standard Description Standard Number Efficiency Measurements IEC 61683/ IS Environmental Testing IEC (1,2,14,30) / Equivalent BIS Standard

12 Charge Controller / MPPT Units Environmental Testing IEC (1,2,14,30) / Equivalent BIS Standard ** In case if the Charge controller is in-built in the inverter, no separate IEC test is required and must additionally conform to the relevant national/international Electrical Safety Standards wherever applicable c. POWER QUALITY REQUIREMENTS The Total Harmonic distortion and ripple content on AC and DC side must not exceed 3 % the provision to measure harmonics should be inbuilt feature of the inverter. Voltage unbalance at the inverter output will be limited to one percent (1 %) The power factor maintained by the inverter should be close to unity The nominal steady state electrical characteristics of the system are as follows: a. Three phase alternating current at 50 Hz plus or minus 0.5 Hz b. Nominal voltage of 110 kv with +10 % to -12 % variations The project shall be designed and capable of being synchronized and operated within a frequency range of 48.5 to 51.5 Hz at Grid Voltages. The Operation of the project outside the nominal voltage and frequency specified above will result in reduction of power output consistent with generator capability curves. While designing the system EPC contractor shall comply with the provisions of the applicable law including, in particular, state grid code as amended from time to time regarding the erection; testing; commissioning; operation and maintenance parameters of the Solar Power Project. Notwithstanding anything in the above, the Inverters should be equipped to synchronize with the Grid under the existing and possible future requirements as per the Grid Codes that may be in effect. d. CABLES, SWITCHES, CIRCUIT BREAKERS, CONNECTORS AND JUNCTION BOXES i. Cables: The cables deployed will be robust and resist high mechanical load and tension. Cable should have High temperature resistance and weather proofing characteristics to ensure long life. The connectors should have high current carrying capacity. All the cables and connectors shall have IEC, UL, TUV or equivalent approval and shall be designed to have excellent UV Resistance. The cables should have Halogen free and flame retardant characteristic. All the cables shall be suitably designed and sized to carry DC and AC currents with the low voltage drops. The cables supplied shall have a proven track record for the use in PV Solar Plants. All cables shall be supplied conforming to IEC 60227/ IS 694 & IEC60502/ IS 1554 Voltage rating: 1,100V AC, 1,500V DC.

13 ii. Switches, Circuit Breakers, Connectors All Switches, Circuit Breakers, Connectors shall be supplied conforming to IEC part I,II, III / IS Part I,II,III/ EN iii. Junction Boxes All Junction Boxes shall be supplied conforming to IP 54(for outdoor)/ IP 21(for indoor) as per IEC 529. e. TRANSFORMER Step-up Transformers will be used to step-up the PCU output voltage to exportable power voltage. In case the transformer is an integral part of the Inverter (PCU), then a separate transformer shall not be required. f. SWITCHYARD EQUIPMENT STRUCTURES The structures will be made up of hot-dip galvanized steel and designed to withstand forces during normal conditions (viz. wind loads & dead load of switchyard components) and abnormal conditions (viz. short circuit, earthquake, etc.). g. EARTHING i. The PV module structure components shall be electrically interconnected and shall be grounded. ii. Earthing shall be done in accordance with IS , provided that earthing conductors shall have a minimum size of 6.0 mm² copper, 10 mm² aluminium or 70 mm² hot dip galvanised steel. Unprotected aluminium or copper-clad aluminium conductors shall not be used for final underground connections to earth electrodes. iii. A minimum of two separate dedicated and interconnected earth electrodes must be used for the earthing of the solar PV system support structure with a total earth resistance not exceeding 5 ohm. iv. The earth electrodes shall have a precast concrete enclosure with a removable lid for inspection and maintenance. The entire earthing system shall comprise non-corrosive components. h. SURGE PROTECTION i. Surge protection shall be provided on the DC side and the AC side of the solar system. ii. The DC surge protection devices (SPDs) shall be installed in the DC distribution box adjacent to the solar grid inverter. iii. The AC SPDs shall be installed in the AC distribution box adjacent to the solar grid inverter. iv. The SPDs earthing terminal shall be connected to earth through the above mentioned dedicated earthing system. The SPDs shall be of type 2 as per IEC

14 i. POWER EVACUATION SYSTEM The power from the PCUs/Transformers is collected in a collecting station (Pooling Substation inside the SPV Plant Boundary) and the high voltage power is routed through the circuit breakers to the Transmission line and be eventually connected to the grid. It is important that the SPV power plant is designed to operate satisfactorily in parallel with the grid within permissible limits of voltage and frequency fluctuation conditions, so as to export the maximum possible units to the grid. The proposed PCU shall have the capability for monitoring the grid parameters (like voltage, frequency and harmonics) and getting the SPV Power Plant output synchronized with the grid on a real time basis. All the associated equipments for the transmission line and the extension of bay in the receiving Grid substation are covered under the evacuation system. j. CAUTION SIGNS The standard caution and danger boards or labels as per Indian Electricity Rules, the AC distribution box near the solar grid inverter and the building distribution board to which the AC output of the solar PV system is connected shall be provided with a noncorrosive caution label. k. METERING i. For the purpose of net metering, the meter alongwith its accessories should be installed as per the CEA guidelines/hperc guidelines/ HPSEBL guidelines along with necessary protection devices. The meter and its accessories will have to be provided by the firm after getting them tested from the HPSEBL approved test centers. Cost of the meter/accessories and its testing will have to borne by the beneficiary only. ii. It is mandatory that the Solar Rooftop PV system shall be connected to the Grid as per the guidelines of HPSEBL along with necessary protection devices. m. DOCUMENTATION The Installer shall supply the following documentation: System description with working principles. System single line diagram. Solar PV array lay-out. Routing diagram of cables and wires. Data sheets and user manuals of the solar PV panels and the solar grid inverter. A system operation and maintenance manual. Name, address, mobile number and address of the service centre to be contacted in case of failure or complaint. Warranty cards.

15 Maintenance registers. n. QUALITY AND WORKMANSHIP Solar PV modules are designed to last 25 years or more. It is therefore essential that all system components and parts, including the mounting structures, cables, junction boxes, distribution boxes and other parts also have a life cycle of at least 25 years. Therefore all works shall be undertaken with the highest levels of quality and workmanship. During inspection HIMURJA and its representatives will pay special attention to neatness of work execution and conformity with quality and safety norms. Non-compliant works will have to be redone at the cost of the Installer. o. WARRANTY The mechanical structures, electrical works including power conditioners/inverters/charge controllers/maximum power point tracker units/distribution boards/digital meters/switch gear/storage batteries, etc. and over all workmanship of the SPV power plants/ systems must be warranted against any manufacturing/ design/ installation defects for a minimum period of 5 years. p. Connection of Bidirectional meter The bidirectional meters will be connected to HPSEBL Grid on following voltages: i) Upto 5 kwp SPV Power Plant = Single Phase line ii) Above 5kWp to15 kwp SPV Power Plant = Three Phase line iii) Above 15kWp to 1 MWp SPV Power Plant = HT/EHT Line Firms will select the PCU and Bidirectional meters accordingly.

16 Annexure I BIDDER FORM 1. Bid No: 2. Name of the work: 3. Last date and time of submission of the documents: 4. Amount of Earnest Money Deposit: DD and Date 5. Date and time of opening of the Bid: 6. Place of opening of the bid: 7. Name and status of firm/company individual to whom the bid document is issued : 8 Validity of Bid 9. Name of the authorized representative to Sign the Bid (Signature of Bidder) with designation All the columns must be filled by the Bidder.

17 Annexure II GENERAL PARTICULARS OF THE BIDDER 1. Name of Bidder: 2 Address for correspondence: 3. Telephone No. and Fax No. 4. address: 5 Name and Designation of the Authorized Representative of the bidder to whom all the references shall be made: 6 Amount and reference of E.M.D. Deposited (Drawn on Bank & D.D. No.& date) 7 Financial capability of the contractor/ Firm for carrying out the work: 8 Has the firm ever been debarred by any Govt. Deptt/Agency/organization for undertaking any work: 9 Details of offer (Mention No of pages): 10. Reference of any other information attached by the Bidder: 11. Authorized representative for any correspondence 12. Whether service center for after sales service set up in the state, give address (Signature of Bidder) with designation

18 Annexure III DECLARATION BY THE BIDDER I/We (herein after referred to as the bidder) being desirous of bidding for the design, manufacture, supply, erection, testing, installation and commissioning of SPV power plants 1 kwp to 500 kwp in different parts in H.P including warranty period of 5 years as shown in scope of bid specification. We have fully understood the nature of the work and carefully noted all the terms and conditions, specifications etc. as mentioned in the bid documents, hereby declare that:- 1. The bidder is fully aware of all the requirements of the bid documents and agrees with all the provisions of the bid documents. 2. The bidder is capable of executing and completing the work as required in the bid. 3. The bidder accepts all risks and responsibilities directly or indirectly connected with the performance of the bid. 4. The bidder is financially solvent and sound to execute the bid. 5. The bidder is sufficiently experienced and competent to perform the contract to the satisfaction of HIMURJA. 6. The information and statements submitted with the bid are true. 7. The bidder has not been debarred from similar type of work by any Govt Dept./Agency/Organization. 8. This offer will remain valid for acceptance for 12 (Twelve) months from the date of finalization of the bid and can be extenteded further. 9. The bidder gives the assurance to execute the bided work as per the specifications, terms and conditions and in exact configuration of the sample submitted on award of the work. (Signature of Bidder) with designation

19 Annexure IV SCHEDULE OF PAST SUPPLIES OF LAST THREE YEARS S No Description Supply order No. and date Name of Agency Date of Supply/ completion as per order Actual date of supply/ commissioning on (Signature of Bidder) with designation Note:- Performance certificate from the concerned utilities along with their communication address, e- mail and FAX No. is required for authentication of certificates.

20 Annexure V Guaranteed Technical Parameters S.No. ITEM PARTICULARS 1 SOLAR PHOTOVOLTAIC MODULES 1.1 Name of Manufacturer 1.2 SIZE (dimension) 1.3 Type 1.4 P max 1.5 IEC certificate Date of issue Agency Validity Enclose a IEC certificate 1.12 Warranty of modules 2 PCU 2.1 TYPE Name of Manufacturer 2.9 Protection features as per Net Metering guidelines of H.P. 3. Solar Meter 3.1 Name of manufacturer 4 Bidirectional Meter 4.1 Name of manufacturer Signature of the Bidder

21 Annexure-VI UNDERTAKING TO BE FURNISHED BY BIDDERS We, M/S with Registered office at undertake to ensure generation of electrical energy from the Solar Power Plant of 1 kwp to 500 kwp to be installed by us as per the details / technical specifications given in Bid document. Authorized Signatory Name of the Company with stamp

22 Financial Bids Name of Work: Rate contract for Design, manufacture, supply, erection, testing and commissioning including warranty, operation & maintenance for 5 years of Grid Interactive Rooftop Solar Power Plants of capacities from 1 kwp to 500 kwp in the State of Himachal Pradesh. We give our unconditional financial rates including all taxes and duties in response of this tender Document issued by HIMURJA. The rates are FOR destination at the sites of the beneficiaries including transportation and insurance etc. 1. For RTS Plants S.No Particulars of Work 1 Up to 10 kwp For 2.5 MW plants at Govt. Building in Shimla city Rate per KW in INR For 10.0 MW plants at Domestic / Institution (registered under society/trust act) / Social Sector / Govt. Building in the State 2 Above 10 kwp up to 50 kwp 3 Above 50 kwp up to 100 kwp 4 Above 100 kwp up to 300 kwp 5 Above 300 kwp up to 500 kwp (Note: The above rates are inclusive of all the taxes, duties etc.) Signature Name Designation with Seal

23 Financial Bids 2. For Net Metering Purpose S. Description No. 1. Solar Meter Rate a) For L.T. (Size wise Rates) b) For H.T (Size wise Rates) 2 Bi-directional meter a) For L.T. (Size wise Rates) b) For H.T. (Size wise Rates) 3. C.T. (Current Transformer) a) For L.T. (Size wise Rates) a) For H.T (Size wise Rates) 4. P.T. (Potential Transformer) a) For L.T. (Size wise Rates) a) For H.T. (Size wise Rates) These rates are for evaluation purpose only and will not be as part of the evaluation for the financial bids. These rates are required for the GCRTS plants to be installed in the Govt buildings. (Note: The above rates are inclusive of all the taxes, duties etc.) Signature Name Designation with Seal