PLEASE COMPLETE AND RETURN AS SOON AS POSSIBLE

Size: px

Start display at page:

Download "PLEASE COMPLETE AND RETURN AS SOON AS POSSIBLE"

Hope Nichols
5 years ago
Views:

1 ED4_PG1_STD Version 3 Manor Farm Industrial Estate, Flint, Flintshire CH6 5UY Telephone +44 (0) Facsimile +44 (0) PLEASE COMPLETE AND RETURN AS SOON AS POSSIBLE TVC Quote No. Company Name Address Customer The above references will be added to all documentation including drawings Delivery Address (if different from above) Note: this document will be the official document used to configure your controller. Complete it carefully as any changes may result in additional cost and delayed delivery. Any features requested in this document that are not already included in the quotation may be subject to a price increase. REQUIREMENTS Please complete the attached questionnaire and supply all relevant information in order that the lift control panel(s) may be designed and manufactured. Inaccurate or incomplete information may delay delivery. For Modernisation jobs, all application data on existing equipment and any requirements not covered on the quotation should be recorded and attached to this form. Please contact TVC if any questions arise regarding the required data. Authorised By Print Name Date TVC cannot accept this document unless signed and dated Internal use only. TVC contract number: 15/09/11 1

2 ED4_PG2_VEC/VF Version 10 MAINS SUPPLY VOLTS IS SUITABLE NEUTRAL AVAILABLE? Yes No PHASE 4 WIRE 3 WIRE HZ PLEASE SUPPLY MOTOR DATA SHEET FOR APPLICATION OR COMPLETE DETAILS BELOW DATA SHEET ATTACHED Y N If yes, Motor data sheet ref number Proceed to NEXT SHEET MOTOR APPLICATION DETAILS / TYPE CAR SPEED m/s V PAY LOAD Kg Hz ROPING 1:1 2:1 RPM SHEAVE DIAMETER mm KW GEAR TYPE AMPS GEAR RATIO FLYWHEEL / HEAVY BRAKE COUPLING Y N TRAVEL m We will assume the answer is no, however, if yes, please supply full details including size & material type BRAKE DETAILS VOLTS DC AMPS TVC preferred standard is 100VDC, 2A max. ADVANCE BRAKE LIFT Y N Allows brake lift before doors are closed for faster floor exit. Mono-stable door switch on door operator required. METHOD OF BRAKE RELEASE MECHANICAL ELECTRICAL DURING HANDWIND PROCEDURE PULSE GENERATOR DETAILS* (Closed Loop only) 1024 PPR 10-30VDC PUSH-PULL COMPLEMENTARY 1024PPR 10-30VDC DIFFERENTIAL RS422 LINE DRIVER 2048PPR 10-30VDC ENDAT ABSOLUTE (MULTI TURN) PROVIDE DETAILS Voltage Pulses per Rev Output Configuration MOTOR FAN VOLTS AMPS PHASES PLEASE NOTE ALL NEW SASSI MOTORS REQUIRE A 230V 1 PHASE 0.14A MOTOR FAN INTERFACE The following assumptions will be made unless specified otherwise using the space below: - Lift counterweighted at 50%. Gear efficiency approximately 70%. Well efficiency approximately 80%. No compensation ropes fitted. For contract speeds up to and including 1.75m/s reduced buffer stroke not applicable. Maximum acceleration & jerk rates Please specify if alternate values are required Lift speed (m/s) Accel rate (m/s²) Jerk rate (m/s³) < < < /03/12 2

3 ED4_PG3_STD Version 14 FAST TRACK (Standard) Options No. OF FLOORS No. OF CAR ENTRANCES 1 2 IF 2 PLEASE INSERT FLOOR MARKINGS FRONT NON FAST TRACK (Non Standard) OPTIONS NON-SELECTIVE DOOR OPENING SELECTIVE DOOR OPENING PLEASE COMPLETE REAR FLOOR ENTRANCES REAR FLOOR HEIGHT (M) 3M floor heights will be assumed if not specified. MAIN (HOMING) FLOOR FIRE FLOOR CONTROL SYSTEM SIMPLEX DUPLEX TRIDENT GROUP If duplex/trident/group serving odd floors, please supply details FULL COLLECTIVE DOWN COLLECTIVE APB CONTROL NON -SEL COLLECTIVE OPTIONAL FEATURES ECO-MODE Y N REFER TO WEBSITE FOR DETAILS PANEL TEST LOW SPEED Y N PLEASE LIST ANY SPECIAL OVER TRAVEL OVERRIDE Y N REQUIREMENTS ADVANCE DOOR OPENING Y N DOOR DETECTOR SUPPLY 110VAC PREFERRED 230VAC 12VDC ALARM SUPPLY Y N 12VDC EMERGENCY LIGHT SUPPLY Y N ALARM CONTROL RELAY X 2 CHANGEOVER CONTACTS Y N REMOTE GOVERNOR TRIP Y N V A REMOTE GOVERNOR RESET Y N V A HANDWIND FLOOR LEVEL BUZZER (not required with HW43) Y N DIGITAL HANDWIND UNIT Y N PANEL MOUNTED THERMOSTAT (5-40ºC) Y N EMERGENCY GENERATOR SUPPLY Y N If yes, complete ESUP questionnaire FIRE CONTROL Only available with fully automatic Y N door control SPECIFICATION Y N STANDARD FEATURES Service control / Car preference Motor room thermostat interface Fire Evacuation EN81-72 Firefighting 90% load weighing 110% load weighing Emergency / fire alarm recall to fire floor, doors dwell closed. EN81-73 Fire Alarm IF YES SPEC REF PAGES TVC CARTOP CONTROL UNIT (CTC1B000) Y N BATTERY BACKUP LIGHT INCLUDED TVC PRE-WIRED - LIMIT SWITCH TREE & RAMP Y N TVC emfone AUTODIALLER Y N CAR ONLY FULL SYSTEM OVERSPEED GOVERNOR SUPPLIED BY TVC Y N UNI-DIRECTIONAL BI-DIRECTIONAL Note: 300mm pulley diameter gear ratio 4:1. Governors with encoders are bi-directional only. TVC ELEVATOR MONITORING (EMU) SYSTEM Y N IF YES NEW EXISTING PROTECTION AGAINST UNINTENDED CAR MOVEMENT Y N IF YES, PLEASE AS EN81-1:1998+A3:2009 / EN81-2:1998+A3:2010 PROVIDE DETAILS 3 06/10/14

4 ED4_PG4_STD Version 6 FAST TRACK (Standard) Options SECTION 1 - POSITION INDICATORS NON FAST TRACK (Non Standard) OPTIONS DIGITAL INDICATORS 24VDC Select type DIGITAL INDICATORS DEWHURST SPECIFY eg ULS32/LD90 STENTORGATE VOLTAGE ILE 4 WIRE SERIAL A&A OMEGA 4 SUPPLY CONNECTION DIAGRAM FOR INTERFACING DRUCEGROVE FITTED AT: CAR MAIN FLOOR ALL FLOORS (If free issue, please ensure we receive the unit at least two weeks ENCODER BOARD REQUIRED Y N before dispatch date, if not we reserve the right to dispatch the contract minus the free issue equipment) HALL LANTERN ARROWS Y N V (DIRECTION OF DEPARTURE) ARE THESE DRIVEN BY THE DIGITAL INDICATORS Y N STANDARD INDICATOR SIGNALS PROVIDED FLOOR POSITION, LIFT DIRECTION, LIFT ON FIRE CONTROL, LIFT OVERLOADED, LIFT OUT OF SERVICE PLEASE PROVIDE LIST OF INDICATOR MESSAGES SECTION 2A - SPEECH UNIT SPEECH UNIT DEWHURST STENTORGATE ILE DRUCEGROVE DIGITALKER Select type SECTION 2B - STANDARD SPEECH SIGNALS PROVIDED LIFT POSITION DOORS OPENING, DOORS CLOSING LIFT GOING UP, LIFT GOING DOWN LIFT ON FIRE CONTROL ALARM LIFT OVERLOADED LIFT OUT OF SERVICE SUPPLY CONNECTION DIAGRAM FOR INTERFACING SPECIAL SPEECH SIGNALS REQUIRED SPECIAL SPEECH PHRASES MAY INCUR AN ADDITIONAL COST SECTION 3 CALL ACCEPTANCE INDICATORS DEWHURST DUAL ILLUMINATION ENBUZZ CAR CALL ACCEPTANCE 24 VDC 20mA LANDING CALL ACCEPTANCE 24 VDC 20mA 06/03/12 4

5 ED4_PG5_STD Version 10 FAST TRACK (Standard) OPTIONS SECTION 5 DOOR OPERATOR DETAILS NON FAST TRACK (Non Standard) OPTIONS DOOR OPERATOR DETAILS FULLY AUTOMATIC CAR & LANDING Y N POWER CAR & MANUAL LANDING Y N IF YES PROCEED TO SECTION 5B TYPE MANUAL CAR & LANDING Y N IF YES PROCEED TO SECTION 5A RETIRING RAMP Y N QTY RAMP VOLTS RAMP CURRENT SECTION 5A RAMP DETAILS QTY RAMP DETAILS (100W MAX TOTAL) Select type 100VDC (TVC PREFERRED) RAMP VOLTS 110VDC RAMP CURRENT 180/185VDC 200VDC SECTION 5B Select type IS DOOR OPERATOR NEW EXISTING SEMATIC SDS VVVF* Select type SELCOM AC / SEMATIC AC DC68* SELCOM VVVF PEGASUS * EXPRESS AC SELCOM VVVF ECO * EXPRESS E TYPE* SELCOM VVVF MIDI/SUPRA * GALMOD** SIEMANS AT18* GALMOD HA** (With fault monitoring) SIEMANS AT25* GALVVVF* SEMATIC F28/F29* GALVVVF HA* (With fault monitoring) SELCOM DC* GALMOH** *Door Nudging Only Available GALMOM** **Door Nudging And Zone Locking Available ECI** FERMATOR VVVF* DOOR NUDGING Y N PROPBROOK** ELECTRICAL ZONE LOCKING Y N 3 PHASE AC (400V) TYPE TYPICAL CABINET DIMENSIONS (mm) VEC/VVVF Height (mm) Width (mm) Depth(mm) 1200 to (1000 incl resistors) 400 Wall or floor mounted DCSCR Height (mm) Width (mm) Depth (mm) Refer to factory. Refer to factory. Refer to factory. HYDRAULIC Height (mm) Width (mm) Depth (mm) 1000 to (1000 incl resistors) 300 or 400 Wall or floor mounted CONTROLLER MECHANICS Front access only. Resistor housing on top or left hand side (if fitted). Please indicate any special requirements regarding size, handing of resistors etc. Typical Cabinet is IP22 rated IS CABINET PLINTH REQUIRED Y N IF YES, PLEASE STATE HEIGHT REQUIRED mm WALL OR FLOOR MOUNTED? WALL FLOOR 13/06/13 5

6 ED4_PG6_SHAFT Version 9 SHAFT SIGNALLING PROXIMITY SWITCHES SUPPLIED BY S TAPEHEAD SUPPLIED BY TVC Only to be completed if tapehead is supplied by others STEEL TAPE LENGTH M SUPPLY VOLTS 110VAC PREFERRED 230VAC BATTERY BACKED UP Y N VPD up to & including 1.75m/s To suit VEC/VVVF/DCSCR RELEVELLING IS NOT AVAILABLE Motor pulse encoder must have a Differential RS422 output or Push pull complementary output Control Panel Motor Encoder GPD up to 1.75m/s (Absolute encoder) To suit VEC/VVVF/DCSCR/HYDVVVF/HYD Overspeed Governor c / w Absolute encoder 20m loom ** Control panel A motor encoder may also be required to feed the drive for closed loop control Is relevelling required Y N ** If Governor is supplied by TVC it comes complete with a connection loom, please specify length required. M If length is not specified,a 20M loom will be supplied VCOM up to 6m/s GPD (Absolute encoder) TO SUIT VEC/VVVF/DCSCR 20m loom ** Is relevelling required Y N Overspeed Governor Control panel Motor Encoder c / w Absolute encoder ** If Governor is supplied by TVC it comes complete with a connection loom, please specify length required. M If length is not specified,a 20M loom will be supplied VCOM up to 6m/s BPD TO SUIT VEC/VVVF/DCSCR TOOTHED BELT SYSTEM SHAFT HEIGHT Control panel Motor Encoder M Is relevelling required Y N 22/11/13 6

7 M R L QUESTIONNAIRE Version 6 Please delete as applicable. WHERE IS CONTROL CABINET TO BE FITTED? LANDING ARCHITRAVE Please provide details H = 2200mm W = 500mm D = 200mm Hinged LHS TVC STANDARD LANDING ARCHITRAVE CONTROL CABINET 304 BRUSHED Stainless Steel 240 GRIT MOTOR INVERTER & DYNAMIC BRAKING RESISTORS TO BE MOUNTED SEPARATE TO CONTROL CABINET, IN CLOSE PROXIMITY TO LIFT MOTOR WHERE IS LIFT MOTOR TO BE FITTED? TOP OF LIFT SHAFT BOTTOM OF LIFT SHAFT Please provide details APPROXIMATE DISTANCE BETWEEN LIFT MOTOR/INVERTER & CONTROL CABINET M LIFT MOTOR TYPE GEARED GEARLESS MOTOR INVERTER SUPPLIED BY TVC TYPE IMPORTANT NOTE: IF ZEIHL ABBEG ZETADYN 2SY INVERTER IS USED, ENSURE K1/K2 CONTACTORS ARE ORDERED WITH 110VAC COILS PLEASE INDICATE SPECIAL REQUIREMENTS REGARDING SIZE, DOOR HINGE, RESISTORS FOR DRIVE CABINET DRIVE CABINET DIMENSIONS (TO BE MOUNTED IN LIFT SHAFT) MOTOR CURRENT =<29A TAPEHEAD 600mmW x 800mmH x 400mmD Resistors will be mounted on top, the height with resistors is 950mm MOTOR CURRENT =<29A VCOM 600mmW x 1000mmH x 400mmD Resistors will be mounted on top, the height with resistors is 1050mmH FOR APPLICATIONS WITH A MOTOR CURRENT GREATER THAN 29A PLEASE REFER TO FACTORY FOR DRIVE CABINET DIMENSIONS METHOD OF HANDWINDING HANDWIND WHEEL FREE WHEEL (GEARLESS) PONY MOTOR PONY MOTOR DETAILS METHOD OF BRAKE RELEASE DURING HANDWIND PROCEDURE MECHANICAL ELECTRICAL CONTROL PANEL OPTIONS Please tick if required CONSUMER UNIT BT SOCKET 3-PIN SOCKET MAINS ISOLATOR SHAFT LIGHT SWITCH CABINET LIGHT 7 13/09/11

Tricon by MCE Data Form Motion Control Engineering Phone (916) Fax: (916)

Tricon by MCE Data Form Motion Control Engineering Phone (916) Fax: (916) Data Form Motion Control Engineering Phone (916) 463-9200 Fax: (916) 463-9201 Car controller specification Foreword Document revision date: 3/15/05 Please fill all ten pages completely. It is very important