Certificate of Compliance

Size: px

Start display at page:

Download "Certificate of Compliance"

Bernice Leonard
6 years ago
Views:

Certificate of Compliance Certificate: 70036125 Master Contract: 170351 Project: 70156820 Date Issued: 2017-09-21 Issued to: Bel Fuse Inc.

1 Certificate of Compliance Certificate: Master Contract: Project: Date Issued: Issued to: Bel Fuse Inc. 206 Van Vorst St Jersey City, New Jersey USA Attention: Editha S. Vergara The products listed below are eligible to bear the CSA Mark shown with adjacent indicators 'C' and 'US' for Canada and US or with adjacent indicator 'US' for US only or without either indicator for Canada only. Issued by: Juan-Carlos Olivera Juan-Carlos Olivera, MSc. PRODUCTS CLASS POWER SUPPLIES - Component Type (UL nd Ed) - Certified to U.S. Stds CLASS POWER SUPPLIES - Component Type (CSA nd Ed) Component type power supplies intended for use with Information Technology and Business Equipment, where the suitability of the combination is to be determined by CSA Group. Switching Power Supply, Models CPA and CPA Model name may be followed by C indicating PCB coating, A for faceplate without Power-One logo, L for output latch, G indicating RoHS version or SXXX or combinations of the different options (where X is alphanumeric character that denotes customer specific changes that do not impact safety requirements). Input Volts Output (DC) Model Range Hz A V A Total W CPA V ac W with 400 LFM airflow DQD 507 Rev Page 1

2 Certificate: Project: Master Contract: Date Issued: CPA V ac W with 400 LFM airflow CPA S383G V ac W with 400 LFM airflow APPLICABLE REQUIREMENTS CAN/CSA-C22.2 No , +Am.1:2011 +Am.2:2014 Information Technology Equipment - Safety - Part 1: General Requirements UL Information Technology Equipment - Safety - Part 1: General Requirements CONDITIONS OF ACCEPTABILITY 1. All secondary output circuits are SELV, and are not hazardous energy levels. It was determined that under fault conditions, SELV limits were maintained. 2. The input and output connectors are not acceptable for field connections, and are only intended for connection to mating connectors of internal wiring inside the end-use equipment. The acceptability of these and the mating connectors relative to secureness, insulating materials, and temperature shall be considered. 3. The equipment has been evaluated for use in a Pollution Degree 2 environment. 4. A suitable electrical, fire and mechanical enclosure shall be provided. 5. The manufacturer's recommended maximum operating ambient temperature is 50 C at full load, 70 C at half of the maximum load. 6. The maximum working voltage present, primary circuit to protective earth, is 295 V rms, 392 V pk. The Electric Strength Tests in the end product shall be based on this value. 7. The power supply shall be properly bonded to the main protective earthing termination in the end product. 8. This unit was investigated as Class I equipment. The power supply shall be properly bonded to the main protective earthing termination in the end product. 9. Magnetic devices (e.g. transformers TR10, TR20) employ an electrical insulation system designated Class F. DQD 507 Rev Page 2

3 Certificate: Project: Master Contract: Date Issued: The protective earthing pin does not make first and break latter than the supply pin connections (Subclause ). This must be taken into consideration when this power supply is installed in the end-use product. DQD 507 Rev Page 3

4 Supplement to Certificate of Compliance Certificate: Master Contract: The products listed, including the latest revision described below, are eligible to be marked in accordance with the referenced Certificate. Project Date Description Product Certification History Update report to include alternate capacitor vendors Update report to add new model CPA S383G and 70C ambient operation Switching Power Supply, Models CPA and CPA (C/US) (transferred from and upgraded to include Am2). DQD 507 Rev Page 1

5 CERTIFICATE No. P Order No Page 1 of 2 Product AC/DC Switching Power Supply Applicant Manufacturer Bel Fuse Inc. 206 Van Vorst St. Jersey City, NJ USA Bel Fuse Inc. 206 Van Vorst St. Jersey City, NJ USA Factory (2) See page 2 Ratings 4A, V~ 50-60Hz Trade mark Model / Type Ref. Principal characteristics A sample of the product was tested and found to be in conformity with Validity Additional information CPA , CPA , CPA S256G, CPA S383G Model name may be followed by C indicating PCB coating, A for faceplate without company logo, L for output latch, G indicating RoHS version or SXXX or combinations of the different options (X is alphanumeric character that denotes customer specific changes that do not impact safety requirements) OFF EN :2006;A11;A1;A12;A2 This certificate documents conformity with the standards shown, and also applies as license for use of Nemkos name and certification mark. The certificate and license is valid as long as the applicable conditions are complied with, and provided that any changes to the product are notified to Nemko for acceptance prior to implementation. New standards or amendments to the standards may imply that the product design must be updated and/or that re-testing and re-certification is necessary. Additional model(s) Compliance with requirements regarding building-in, protection against electric shock and Electromagnetic Compatibility (EMC) must be checked when the equipment is built-in a completed product or forms a part of a complete system. No additional models Date of issue Sweet Yuan Certification Department Nemko AS Gaustadalléen 30, P.O. Box 73 Blindern, 0314 Oslo, Norway TEL FAX info@nemko.com ENTERPRISE NUMBER NO nemko.com

CERTIFICATE No. P16220971 Order No. 305908 Page 2 of 2 Factories Bel Power Solutions Asia Pacific Electronics (Shenzhen) Co.,Ltd.

6 CERTIFICATE No. P Order No Page 2 of 2 Factories Bel Power Solutions Asia Pacific Electronics (Shenzhen) Co.,Ltd. Building# 6, Nanming Road, Gongming Town, Huahong Xintong Industrial Park, Guangming District, Shenzhen China Bel Power Solutions, s.r.o. Areal ZTS Dubnica nad Vahom Slovakia Date of issue Sweet Yuan Certification Department Nemko AS Gaustadalléen 30, P.O. Box 73 Blindern, 0314 Oslo, Norway TEL FAX info@nemko.com ENTERPRISE NUMBER NO nemko.com

7 Ref. Certif. No. NO91738 IEC SYSTEM FOR MUTUAL RECOGNITION OF TEST CERTIFICATES FOR ELECTRICAL EQUIPMENT (IECEE) CB SCHEME SYSTEME CEI DACCEPTATION MUTUELLE DE CERTIFICATS DESSAIS DES EQUIPEMENTS ELECTRIQUES (IECEE) METHODE OC CB TEST CERTIFICATE CERTIFICAT D'ESSAI OC Product Produit Name and address of the applicant Nom et adresse du demandeur Name and address of the manufacturer Nom et adresse du fabricant Name and address of the factory Nom et adresse de l'usine Note: When more than one factory, please report on page 2 Note: Lorsque il y plus d'une usine, veuillez utiliser la deuxième page Ratings and principal characteristics Valeurs nominales et caractéristiques principales Trademark (if any) Marque de fabrique (si elle existe) AC/DC Switching Power Supply Bel Fuse Inc. 206 Van Vorst St. Jersey City, NJ USA Bel Fuse Inc. 206 Van Vorst St. Jersey City, NJ USA Additional information on page 2 4A, V~ 50-60Hz Type of Manufacturer s Testing Laboratories used Type de programme du laboratoire d essais constructeur Model / Type Ref. Ref. De type CTF-3 CPA , CPA , CPA S256G, CPA S383G Additional information (if necessary may also be reported on page 2) Les informations complémentaires (si nécessaire, peuvent être indiqués sur la deuxième page A sample of the product was tested and found to be in conformity with Un échantillon de ce produit a été essayé et a été considéré conforme à la As shown in the Test Report Ref. No. which forms part of this Certificate Comme indiqué dans le Rapport dessais numéro de référence qui constitue partie de ce Certificat Model name may be followed by C indicating PCB coating, A for faceplate without company logo, L for output latch, G indicating RoHS version or SXXX or combinations of the different options (X is alphanumeric character that denotes customer specific changes that do not impact safety requirements) Additional information on page 2 IEC (ed.2);am1;am This CB Test Certificate is issued by the National Certification Body Ce Certificat dessai OC est établi par l'organisme National de Certification Gaustadalléen 30 NO-0373 Oslo, Norway Date: Signature: Sweet Yuan Certification Department Issued /2

8 Ref. Certif. No. NO91738 Bel Power Solutions Asia Pacific Electronics (Shenzhen) Co.,Ltd. Building# 6, Nanming Road, Gongming Town, Huahong Xintong Industrial Park, Guangming District, Shenzhen China Bel Power Solutions, s.r.o. Areal ZTS Dubnica nad Vahom Slovakia Gaustadalléen 30 NO-0373 Oslo, Norway Date: Signature: Sweet Yuan Certification Department Issued /2

Test Report issued under the responsibility of www.nemko.com Report Number....: 305908 TEST REPORT IEC 60950-1 Information technology equipment Safety Part 1: General requirements Date of issue.

9 Test Report issued under the responsibility of Report Number....: TEST REPORT IEC Information technology equipment Safety Part 1: General requirements Date of issue...: 14 April 2016 Total number of pages...: 48 Applicant s name...: Bel Fuse Inc. Address...: 206 Van Vorst St., Jersey City, NJ Test specification: Standard...: IEC :2005 (Second Edition) + Am 1: Am 2:2013 Test procedure...: CB-Scheme Non-standard test method...: N/A Test Report Form No.... : IEC60950_1F Test Report Form(s) Originator...: SGS Fimko Ltd Master TRF...: Dated Copyright 2014 IEC System of Conformity Assessment Schemes for Electrotechnical Equipment and Components (IECEE System). All rights reserved. This publication may be reproduced in whole or in part for non-commercial purposes as long as the IECEE is acknowledged as copyright owner and source of the material. IECEE takes no responsibility for and will not assume liability for damages resulting from the reader's interpretation of the reproduced material due to its placement and context. This report is not valid as a CB Test Report unless signed by an approved CB Testing Laboratory and appended to a CB Test Certificate issued by an NCB in accordance with IECEE 02. General disclaimer: The test results presented in this report relate only to the object tested. This report shall not be reproduced, except in full, without the written approval of the Issuing CB Testing Laboratory. The authenticity of this Test Report and its contents can be verified by contacting the NCB, responsible for this Test Report. This Test Report, when bearing the Nemko name and logo is only valid when issued by a Nemko laboratory, or by a laboratory having special agreement with Nemko.

Page 2 of 48 Report No. 305908 Test item description... : AC/DC Switching Power Supply Trade Mark...: Manufacturer...: Same as Applicant Model/Type reference.

10 Page 2 of 48 Report No Test item description... : AC/DC Switching Power Supply Trade Mark...: Manufacturer...: Same as Applicant Model/Type reference...: CPA , CPA , CPA S256G, CPA S383G. (Model name may be followed by C indicating PCB coating, A for faceplate without company logo, L for output latch, G indicating RoHS version or SXXX or combinations of the different options (X is alphanumeric character that denotes customer specific changes that do not impact safety requirements)) Ratings...: 4 A, V~, Hz, (See general Remarks for secondary DC Outputs) Testing procedure and testing location: CB Testing Laboratory: Nemko USA Inc. Testing location/ address... : 2210 Faraday Ave. Suite 150, Carlsbad, CA 92008, USA Testing Laboratory: CTF3 Bel Power Solutions, s.r.o. Testing location/ address... : ArealZTS Dubnica n.vahom c Dubnica nad Vahom SLOVAKIA Tested by (name + signature)... : Witnessed by (name + signature)... : Editha Vergara Luis Gonzalez Approved by (name + signature)... : Jeff Bush Report History: Original report List of Attachments (including a total number of pages in each attachment): Attachment 1: European Group Differences and National Deviations pages Documented deviations contain individual national documents for several European countries that are included in the European Group Deviations. The European Group Difference: EN60950:2006/A11:2009/A:2010/A12:2011/A2:2013 are considered Normative. The individual national documents (Denmark, Finland, Germany, Ireland, Norway, Spain, Sweden, Switzerland and United Kingdom) are considered informative and included at the manufacturer s request. Attachment 2: Miscellaneous Documentation, e.g. Installation instructions, Magnetics, Photos, etc pages (Not for publication Engineering use only) TRF No. IEC60950_1F

11 Page 3 of 48 Report No Summary of testing General Power supply All comments relate to all models, unless specifically stated. The equipment is an enclosed, Class I switch mode power supply with universal AC input and multiple DC voltage outputs for building-in. This report covers multiple models and all comments / tests apply to all models unless otherwise indicated. Testing was conducted on various models as indicated ; The unit is intended to operate at an altitude of up to 3048m. This equipment is intended to be operated at an altitude of up to 3048 m so the clearance is multiplied by the altitude correction factor (1.15), specified in table A.2 of IEC nd Edition: Refer to Tables and ; Safety instructions. Instructions and equipment markings related to safety are to be provided in a language, which is acceptable in the country in which the equipment is to be sold. English language verified ; IT power distribution systems. The equipment complies with the requirements for connection to the Norwegian IT power systems. The following information should be given (but is not required) in the installation instruction: This product is also designed for IT power system with Phase to Phase voltage 230V ; Number and location of protective devices. In Norway, IT power distribution system is used. Equipment with a single protective device is accepted in Norway. Other countries may have additional requirements ; Warning to service personnel. After operation of the protective device, the equipment is still under voltage if it is connected to an IT-power system. A warning is required for service personnel. Norway does not require this warning. 4.5; Thermal requirements. Heating tests were conducted with external cooling of 400LFM. TRF No. IEC60950_1F

12 Page 4 of 48 Report No Summary of testing: Tests performed (name of test and test clause): 1) Input ) Durability ) Capacitance Discharge ) SELV Reliability ) Protective Bonding ) Humidity ) Working Voltage Measurement ) Hazardous Voltage Measurement ) Mechanical and Stress Relief ) Heating ) Touch Current ) Electric Strength ) Component Failure ) Abnormal Operation ) PS Output Overload and Short Testing location: Bel Power Solutions, s.r.o. ArealZTS Dubnica n.vahom c Dubnica nad Vahom SLOVAKIA Summary of compliance with National Differences: List of countries addressed: Austria (AT), Australia (AU), Canada (CA), Denmark (DK), Finland (FI), Germany (DE), Ireland (IE), Israel (IS), Korea (KR), Norway (NO), Slovenia (SI), Spain (ES), Sweden (SE), Switzerland (CH), United Kingdom (GB), United States of America (US) The product fulfils the requirements of : EN : A11: A1: A12: A2:2013 TRF No. IEC60950_1F

Page 5 of 48 Report No. 305908 Copy of marking plate: The artwork may be only a draft. The use of certification marks on a product must be authorized by the respective NCBs that own these marks.

13 Page 5 of 48 Report No Copy of marking plate: The artwork may be only a draft. The use of certification marks on a product must be authorized by the respective NCBs that own these marks. (Additional requirements for markings. See 1.7 NOTE) Calibration Measurement uncertainty Evaluation of results All instruments used in the tests given in this test report are calibrated and traceable to national or international standards. Further information about traceability will be given on request. Measurement uncertainties are calculated for all instruments and instrument set-ups given in this report. Calculations are based on the principles given in the standard EA-4/02 (Dec. 1999), IEC Guide 115:2007, Nemko routine L227 and other relevant internal Nemko-procedures. Further information about measurement uncertainties will be given on request. If not explicitly stated otherwise in the standard, the test is passed if the measured value is equal to or below (above) the limit line, regardless of the measurement uncertainty. If the measured value is above (below) the limit line, the test is not passed - ref IEC Guide 115:2007, and Nemko routine L220. The instrumentation accuracy is within limits agreed by IECEE-CTL (ref. Nemko routine L227). TRF No. IEC60950_1F

14 Page 6 of 48 Report No Test item particulars: Equipment mobility... : [] movable [] hand-held [] transportable [] stationary [ X ] for building-in [] direct plug-in Connection to the mains... : [] pluggable equipment [ X ] type A [] type B [] permanent connection [] detachable power supply cord [] non-detachable power supply cord [ X ] not directly connected to the mains Operating condition...: [ X ] continuous [] rated operating / resting time: Access location...: [] operator accessible [] restricted access location Over voltage category (OVC)...: [] OVC I [ X ] OVC II [] OVC III [] OVC IV [] other: Mains supply tolerance (%) or absolute mains supply -10%, +6% values...: Tested for IT power systems... : [X] Yes (Norway) [ ] No IT testing, phase-phase voltage (V)... : 230 Class of equipment...: [ X ] Class I [] Class II [] Class III [] Not classified Considered current rating of protective device as part of the building installation (A)...: 16A for Europe, 20 A for North America Pollution degree (PD)... : [] PD 1 [ X ] PD 2 [] PD 3 IP protection class... : IPX0 Temperature, Ambient ( C)... : 50 C maximum load, 70 C 50% of maximum load Altitude during operation (m)... : 3048 m Altitude of test laboratory (m)... : 94 m Mass of equipment (kg)... : 0.78 kg Possible test case verdicts: - test case does not apply to the test object... : N/A - test object does meet the requirement... : P (Pass) - test object does not meet the requirement... : F (Fail) Testing: Date of receipt of test item... : May 2015 Date(s) of performance of tests... : May 2015, March 2016 TRF No. IEC60950_1F

15 Page 7 of 48 Report No General remarks: "(see appended table)" refers to a table appended to the report. "(see Enclosure #)" refers to additional information appended to the report. The test results presented in this report relate only to the object tested. This report shall not be reproduced, except in full, without the written approval of the Issuing testing laboratory. Throughout this report a comma / point is used as the decimal separator. Manufacturer s Declaration per sub-clause of IECEE 02: The application for obtaining a CB Test Certificate includes more than one factory location and a declaration from the Manufacturer stating that the sample(s) submitted for evaluation is (are) representative of the products from each factory has been provided... : When differences exist; they shall be identified in the General product information section. Name and address of factory (ies)... : Yes Not applicable Bel Power Solutions, s.r.o. ArealZTS Dubnica n.vahom c Dubnica nad Vahom SLOVAKIA Bel Power Solutions Asia Pacific Electronics (Shenzhen) Co.,Ltd. Building# 6, Nanming Road, Gongming Town Huahong Xintong Industrial Park Guangming District Shenzhen PEOPLE'S REPUBLIC OF CHINA TRF No. IEC60950_1F

16 Page 8 of 48 Report No General product information: This test report replaces Nemko test report Ref. No , with appended CB certificate No. NO This test report includes the addition of the 70 C ambient operation. There is no change in the construction of the equipment. Therefore, only tests associated with the extended temperature rating were conducted. For continuity, the entire report has been reissued, including the additional evaluation highlighted in Bold text. This test report is based on a TUV SUD test report Ref. No with appended CB cert Ref. No. DE , evaluated to the requirements of IEC : nd ed. + A1:2009. This test report includes an upgrade to IEC :2005 (Second Edition) + Am 1: Am 2:2013, additional evaluation of the power supply to the requirements of IT power systems and an engineering evaluation of the Leakage at the output of the PSU. For continuity, data from the original TUV report is included in this report, along with the additional evaluation referenced. CPA200 and CPA250 Series are AC to DC switching power supplies designed to be used in hot-plug applications in Compact PCI racks. The input/output connector is specifically designed for use in this application. The power supplies have four outputs that derive their power from two separate power supplies. The units can be operated at maximum 50 C maximum ambient. Model differences: Model CPA S256G is exactly the same as CPA G except for the model name. Secondary DC Output(s): Model Input (AC) Output (DC) V A Hz V A W CPA *) CPA **) CPA S256G CPA **) 4530S383G *) Maximum total output 200 W with minimum 400 LFM airflow **) Maximum total output 250 W with minimum 400 LFM airflow TRF No. IEC60950_1F

17 Page 9 of 48 Report No Conditions of Acceptability: These models require: 1) A suitable fire enclosure at end use. 2) A reliable ground (Protective Earth) connection at end use. 3) Type of connection to AC Mains evaluated in end use equipment. Abbreviations used in the report: - normal conditions... N.C. - single fault conditions... S.F.C - functional insulation... OP - basic insulation... BI - double insulation... DI - supplementary insulation... SI - between parts of opposite polarity... BOP - reinforced insulation... RI Indicate used abbreviations (if any):... None TRF No. IEC60950_1F

Certificate of Compliance

Certificate of Compliance Certificate: 2235802 (LR 38879) Master Contract: 173688 Project: 2235802 Date Issued: 2009/11/03 Issued to: Power-One, Inc 740 Calle Plano Camarillo, CA 93012 USA Attention: Ms.