TEST REPORT IEC Information technology equipment Safety Part 1: General requirements

Transcription

1

2

3 Test Report issued under the responsibility of: NCB TÜ V SÜ D SB te Ltd 1 Science ark Drive, Singapore TEST REORT IEC Information technology equipment Safety art 1: General requirements Report Number.... : Date of issue... : Total number of pages Applicant s name... : Address... : Simplo Technology Co., Ltd. No. 471, Sec. 2, a Teh Rd, Hu Kou, Hsin Chu Hsien, TAIWAN Test specification: Standard... : IEC :2005 (Second Edition) + Am 1: Am 2:2013 Test procedure... : Non-standard test method... : Test Report Form No.... : Test Report Form(s) Originator... : CB Scheme IEC60950_1F SGS Fimko Ltd Master TRF... : Dated Copyright 2014 IEC System of Conformity Assessment Schemes for Electrotechnical Equipment and Components (IECEE System). All rights reserved. This publication may be reproduced in whole or in part for non-commercial purposes as long as the IECEE is acknowledged as copyright owner and source of the material. IECEE takes no responsibility for and will not assume liability for damages resulting from the reader's interpretation of the reproduced material due to its placement and context. If this Test Report Form is used by non-iecee members, the IECEE/IEC logo and the reference to the CB Scheme procedure shall be removed. This report is not valid as a CB Test Report unless signed by an approved CB Testing Laboratory and appended to a CB Test Certificate issued by an NCB in accordance with IECEE 02. General disclaimer: The test results presented in this report relate only to the object tested. This report shall not be reproduced, except in full, without the written approval of the Issuing CB Testing Laboratory. The authenticity of this Test Report and its contents can be verified by contacting the NCB, responsible for this Test Report. Beitou District, Taipei City, 11270, Taiwan age 1 of 10 Test Report IEC60950_1F

4 Test item description... : Trade Mark... : Manufacturer... : Model/Type reference... : Ratings... : RECHARGEABLE LI-ION BATTERY SIMLO Same as applicant. N150BAT Vdc, 5400 mah or 5600 mah or 62 Wh Testing procedure and testing location: CB Testing Laboratory: TÜ V SÜ D Asia Ltd. Taiwan Branch Testing location/ address... : 7F., No.37, Sec. 2, Zhongyang S., Rd., Beitou District, Taipei City, 11270, TAIWAN. Associated CB Testing Laboratory: Testing location/ address... : Tested by (name + signature)... : Approved by (name + signature)... : Mr. Owen Hsu Mr. Duck Lee Testing procedure: TM/CTF Stage 1: Testing location/ address... : Tested by (name + signature)...: Approved by (name + signature)...: Testing procedure: WMT/CTF Stage 2: Testing location/ address...: Tested by (name + signature)... : Witnessed by (name + signature)... : Approved by (name + signature)... : Testing procedure: SMT/CTF Stage 3 or 4: Testing location/ address... : Tested by (name + signature)...: Witnessed by (name + signature)...: Approved by (name + signature)...: Supervised by (name + signature)...: Beitou District, Taipei City, 11270, Taiwan age 2 of 10 Test Report IEC60950_1F

5 List of Attachments (including a total number of pages in each attachment): Original Test Report No.: pages + 99 pages attachments Attachments No. 1 IEC 62133:2012 Test Report 8 pages Summary of testing: Tests performed (name of test and test clause): All test results were found satisfactory in accordance with IEC :2005 (2 nd Edition) + A1: A2:2013 and EN : A11: A1: A12: A2:2013 Testing location: All tests as described in Test Case and Measurement Sections were performed at the laboratory described on page 2. Summary of compliance with National Differences: List of countries addressed According to CB Bulletin, the National Differences include Australia (AU), Canada (CA), China (CN), Germany (DE), Israel (IL), Korea (KR), Switzerland (CH) and United States of America (US). Group Differences (CENELEC COMMON MODIFICATIONS) as listed in the European Standard are recorded in this Report. The product fulfils the requirements of IEC : A1: A2:2013/ EN : A11: A1: A12: A2:2013 Copy of marking plate: The artwork below may be only a draft. The use of certification marks on a product must be authorized by the respective NCBs that own these marks. (Additional requirements for markings. See 1.7 NOTE). See Attachment No. 3 of Test Report No.: Beitou District, Taipei City, 11270, Taiwan age 3 of 10 Test Report IEC60950_1F

6 Test item particulars...: Equipment mobility...: [] movable [] hand-held [X] transportable [] stationary [] for building-in [] direct plug-in Connection to the mains...: [] pluggable equipment [] type A [] type B [] permanent connection [] detachable power supply cord [] non-detachable power supply cord [X] not directly connected to the mains Operating condition...: [X] continuous [] rated operating / resting time: Access location...: [X] operator accessible [] restricted access location Over voltage category (OVC)...: [] OVC I [] OVC II [] OVC III [] OVC IV [X] other: Not directly connected to AC or DC mains. Mains supply tolerance (%) or absolute mains supply values...: Tested for IT power systems...: [] Yes IT testing, phase-phase voltage (V)...: [X] No Class of equipment...: [] Class I [] Class II [X] Class III [] Not classified Considered current rating of protective device as part of the building installation (A)...: ollution degree (D)...: [] D 1 [X] D 2 [] D 3 I protection class...: Ordinary Altitude during operation (m)...: Up to 2,000 Altitude of test laboratory (m)...: below 2,000 Mass of equipment (kg)...: Approx ossible test case verdicts: - test case does not apply to the test object... : - test object does meet the requirement... : (ass) - test object does not meet the requirement... : F (Fail) Testing... : Date of receipt of test item... : Date (s) of performance of tests... : to General remarks: "(See Enclosure #)" refers to additional information appended to the report. "(See appended table)" refers to a table appended to the report. Throughout this report a comma / point is used as the decimal separator. Beitou District, Taipei City, 11270, Taiwan age 4 of 10 Test Report IEC60950_1F

7 Manufacturer s Declaration per sub-clause of IECEE 02: The application for obtaining a CB Test Certificate includes more than one factory location and a declaration from the Manufacturer stating that the sample(s) submitted for evaluation is (are) representative of the products from each factory has been provided... : Yes Not applicable When differences exist; they shall be identified in the General product information section. Name and address of factory (ies)... : 1) Simplo Technology (ChangShu) Inc. (ID No.: 60634) No. 2, Dongnan Rd., Changshu, Jiangsu, EOLE S REUBLIC OF CHINA 2) Simplo Technology (ChongQing) Inc. (ID No ) No.2 Zongbao Avenue, Shapingba District, Chongqing, EOLE S REUBLIC OF CHINA Report No. < > The modifications for this report are to : 1. Revise material of enclosure to V-1. See appended table for details. 2. Revise material of Nameplate Marking Label. See appended table for details. 3. Change the equipment mobility from for building-in to transportable. See page 4 for details. For the above described modification the following Clause/Testing were considered to be necessary: S/N Clause/Testing Remark/Comments Verdict 1. Clause 4.2 Mechanical strength 2. Clause 4.3 Design and construction 3. Clause 4.6 Openings in enclosures 4. Clause 4.7 Resistance to fire 5. Table List of critical components Beitou District, Taipei City, 11270, Taiwan age 5 of 10 Test Report IEC60950_1F

8 General product information: This equipment is a RECHARGEABLE LI-ION BATTERY (only SELV circuit inside) classified as information technology equipment. The RECHARGEABLE LI-ION BATTERY complied with the IEC 62133:2012 requirements see attachment IEC 62133:2012 Test Report for details. The RECHARGEABLE LI-ION BATTERY equipped with the battery cell is CB certified component of IEC 62133:2012, see appended table for details. The maximum ambient temperature specified by manufacturer is 45 C. Specification for the RECHARGEABLE LI-ION BATTERY is as follows: Battery Cell Configuration 3S2 Nominal voltage (Vdc) 11.1 Nominal capacity (mah, Wh) 5400 mah or 5600 mah or 62 Wh Maximum Charge Voltage (Vdc) 12.9 Optimum charge current (A) 3.2 Maximum discharge current (A) 6 End voltage (Vdc) 9.0 Abbreviations used in the report: - normal conditions N.C. - single fault conditions S.F.C - functional insulation O - basic insulation BI - double insulation DI - supplementary insulation SI - between parts of opposite polarity BO - reinforced insulation RI Indicate used abbreviations (if any) Beitou District, Taipei City, 11270, Taiwan age 6 of 10 Test Report IEC60950_1F

9 IEC Clause Requirement + Test Result - Remark Verdict 4.2 Mechanical strength General See below. Rack-mounted equipment Steady force test, 10 N Steady force test, 30 N Steady force test, 250 N 250 N applied to outer enclosure No energy or other hazards Impact test Fall test Swing test Drop test; height (mm)... : The equipment is subjected to three impacts that result from being dropped onto a horizontal surface. The height of drop: 1,000 mm ± 10 mm Stress relief test After 7 h at 90 C and cooling down to room temperature, no shrinkage, distortion or loosing of enclosure parts was noticeable. Above test temperature is based upon manufacturer s declaration. Beitou District, Taipei City, 11270, Taiwan age 7 of 10 Test Report IEC60950_1F

10 IEC Clause Requirement + Test Result - Remark Verdict 4.3 Design and construction Edges and corners Edges and corners of the enclosure are rounded. 4.6 Openings in enclosures Top and side openings See Dimensions (mm)... : Bottoms of fire enclosures See Construction of the bottomm, dimensions (mm).. : Doors or covers in fire enclosures No door or cover Openings in transportable equipment No openings Constructional design measures Dimensions (mm)... : Evaluation measures for larger openings Use of metallized parts Adhesives for constructional purposes Adhesive label is a part of the fire enclosure. Conditioning temperature ( C), time (weeks)... : Top and Bottom enclosure were secured together by Snap fit and solvent. 100 C ± 2 C for one week and following by the standard conditioning. The barrier or screen did not fall off or partly dislodge as a result of these tests. Beitou District, Taipei City, 11270, Taiwan age 8 of 10 Test Report IEC60950_1F

11 IEC Clause Requirement + Test Result - Remark Verdict 4.7 Resistance to fire Reducing the risk of ignition and spread of flame It s a battery pack with SELV circuit only and covered by min. V-1 enclosure. Method 1, selection and application of components wiring and materials Method 2, application of all of simulated fault condition tests Selection and application of components and materials which minimize the possibility of ignition and spread of flame Conditions for a fire enclosure See below arts requiring a fire enclosure With having the following components: - Components with windings. - wiring. - Semiconductor devices, transistors, diodes, integrated circuits. - Resistors, capacitors, inductors. - Battery cell. The fire enclosure is required arts not requiring a fire enclosure See Materials General Integrated circuits and small electrical parts mounted on a printed wiring board min. rated V Materials for fire enclosures See appended table Materials for components and other parts outside fire enclosures Materials for components and other parts inside fire enclosures No components or parts outside fire enclosures. Integrated circuits and small electrical parts mounted on a printed wiring board min. rated V Materials for air filter assemblies No air filters assemblies Materials used in high-voltage components No high voltage component used. Beitou District, Taipei City, 11270, Taiwan age 9 of 10 Test Report IEC60950_1F

12 1.5.1 TABLE: List of critical components Object/part No. Revise components: Nameplate Marking Label - Material of Nameplate Marking Label - Adhesive for Nameplate Marking Label secure Enclosure Manufacturer/ trademark Cymmetrik Enterprise Co., Ltd. Sichuan Dongfang Insulating Material Co., Ltd 3M China Co., Ltd. Formosa Chemicals & Fibre Corp plastics Div. Type/model Technical data Standard (Edition / year) CM V-0, 80 C thickness 0.1 mm DFD250B VTM-0, 105 C minimum thickness mm S C minimum thickness 0.05 mm AC3710 V-1, 80 C, 0.45 mm. thick minimum. UL 969 UL 94 UL 746C UL 969 UL 94 Supplementary information: 1) rovided evidence ensures the agreed level of compliance. See OD-CB2039. UL UL UL UL Mark(s) of conformity 1 ) Beitou District, Taipei City, 11270, Taiwan age 10 of 10 Test Report IEC60950_1F

13 Attachment No. 1 Test Report issued under the responsibility of: TEST REORT IEC Secondary cells and batteries containing alkaline or other non-acid electrolytes Safety requirements for portable sealed secondary cells, and for batteries made from them, for use in portable applications Report Number.... : Date of issue... : Total number of pages... 8 Applicant s name... : Address... : Simplo Technology Co., Ltd. No. 471, Sec. 2, a Teh Rd, Hu Kou, Hsin Chu Hsien, TAIWAN Test specification: Standard...: Test procedure...: Non-standard test method... : Test Report Form No....: Test Report Form(s) Originator...: IEC 62133: 2012 (Second Edition) CB Scheme IEC62133B UL(Demko) Master TRF... : Dated Copyright 2013 Worldwide System for Conformity Testing and Certification of Electrotechnical Equipment and Components (IECEE), Geneva, Switzerland. All rights reserved. This publication may be reproduced in whole or in part for non-commercial purposes as long as the IECEE is acknowledged as copyright owner and source of the material. IECEE takes no responsibility for and will not assume liability for damages resulting from the reader's interpretation of the reproduced material due to its placement and context. If this Test Report Form is used by non-iecee members, the IECEE/IEC logo and the reference to the CB Scheme procedure shall be removed. This report is not valid as a CB Test Report unless signed by an approved CB Testing Laboratory and appended to a CB Test Certificate issued by an NCB in accordance with IECEE 02. Test item description...: Trade Mark...: Manufacturer...: Model/Type reference...: Ratings...: RECHARGEABLE LI-ION BATTERY SIMLO Same as applicant. N150BAT-6 (3ICR19/65-2) 11.1 Vdc, 5400 mah or 5600 mah or 62 Wh Beitou District, Taipei City, 11270, Taiwan age 1 of 8 Test Report IEC62133B

14 Testing procedure and testing location: CB Testing Laboratory: Testing location/ address... : Associated CB Testing Laboratory: Testing location/ address... : Tested by (name + signature)... : Approved by (name + signature)... : Testing procedure: TM Testing location/ address... : TÜ V SÜ D Asia Ltd. Taiwan Branch 7F., No.37, Sec. 2, Zhongyang S., Rd., Beitou District, Taipei City, 11270, TAIWAN. See IEC Test Report See IEC Test Report Tested by (name + signature)... : Approved by (name + signature)... : Testing procedure: WMT Testing location/ address... : Tested by (name + signature)... : Witnessed by (name + signature)... : Approved by (name + signature)... : Testing procedure: SMT Testing location/ address... : Tested by (name + signature)... : Approved by (name + signature)... : Supervised by (name + signature).. : Beitou District, Taipei City, 11270, Taiwan age 2 of 8 Test Report IEC62133B

15 List of Attachments (including a total number of pages in each attachment): Summary of testing: Tests performed (name of test and test clause): All test results were found satisfactory in accordance with IEC 62133: 2012 and EN 62133: Charging procedures for test purposes First procedure Moulded case stress at high ambient temperature (battery) Free fall Testing location: All tests as described in Test Case and Measurement Sections were performed at the laboratory described on page 2. Summary of compliance with National Differences The product fulfils the requirements of IEC 62133:2012 / EN 62133:2013. Beitou District, Taipei City, 11270, Taiwan age 3 of 8 Test Report IEC62133B

16 Copy of marking plate: Date of manufacture designation: Date code: C Y WW RR SSSSS: Total 14 digits - C: Factory ID - Y: Year of Manufacturing - YY: Year code (ex. 2006=06) - WW: Week of Manufacturing - : Model # - RR: Version - SSSSS: Serial number The artwork below may be only a draft. The use of certification marks on a product must be authorized by the respective NCBs that own these marks. Beitou District, Taipei City, 11270, Taiwan age 4 of 8 Test Report IEC62133B

17 Test item particulars...: Classification of installation and use...: For use in portable applications. Supply connection...: DC connector Recommend charging method declaired by the manufacturer... : CC-CV or clause Discharge current (0,2 I t A)... : 1120 ma Specified final voltage... : 9.0 Vdc Chemistry... : nickel systems... lithium systems Recommend of charging limit for lithium system Upper limit charging voltage per cell...: 4.35 Vdc Maximum charging current...: 3.2 A Charging temperature upper limit...: 45 C Charging temperature lower limit...: 0 C olymer cell electrolyte type... : gel polymer... solid polymer ossible test case verdicts: - test case does not apply to the test object... : - test object does meet the requirement... : (ass) - test object does not meet the requirement... : F (Fail) Testing... : Date of receipt of test item... : Date (s) of performance of tests... : to General remarks: The test results presented in this report relate only to the object tested. This report shall not be reproduced, except in full, without the written approval of the Issuing testing laboratory. "(See Enclosure #)" refers to additional information appended to the report. "(See appended table)" refers to a table appended to the report. Throughout this report a comma / point is used as the decimal separator. Manufacturer s Declaration per sub-clause of IECEE 02: The application for obtaining a CB Test Certificate includes more than one factory location and a declaration from the Manufacturer stating that the sample(s) submitted for evaluation is (are) representative of the products from each factory has been provided... : Yes Not applicable When differences exist; they shall be identified in the General product information section. Beitou District, Taipei City, 11270, Taiwan age 5 of 8 Test Report IEC62133B

18 Name and address of factory (ies)... : 1) Simplo Technology (ChangShu) Inc. (ID No.: ) No. 2, Dongnan Rd., Changshu, Jiangsu, EOLE S REUBLIC OF CHINA 2) Simplo Technology (ChongQing) Inc. (ID No ) No.2 Zongbao Avenue, Shapingba District, Chongqing, EOLE S REUBLIC OF CHINA Report No. < > The modifications for this report are to : 1. Revise material of enclosure to V-1. Detailed information, See appended table: Critical components information. 2. Revise material of Nameplate Marking Label. Detailed information, See appended table: Critical components information. For the above described modification the following Clause/Testing was considered to be necessary: S/N Clause/Testing Remark/Comments Verdict 1. Cause 6 Type test conditions 2. Clause 8 Specific requirements and tests (lithium systems) 3. Clause Moulded case stress at high ambient temperature (battery) 4. Clause Free fall 5. Table Critical components information General product information: This equipment is a RECHARGEABLE LI-ION BATTERY for use in portable applications. The maximum ambient temperature specified by manufacturer is 45 C. Specification for the RECHARGEABLE LI-ION BATTERY are as follows: Battery Cell Configuration 3S2 Nominal voltage (Vdc) 11.1 Nominal capacity (mah, Wh) 5400 mah or 5600 mah or 62 Wh Maximum Charge Voltage (Vdc) 12.9 Optimum charge current (A) 3.2 Maximum discharge current (A) 6 End voltage (Vdc) 9.0 Weight (kg) Approx The final evaluation of the battery must be conducted in the end product for which the battery will be used. Beitou District, Taipei City, 11270, Taiwan age 6 of 8 Test Report IEC62133B

19 IEC Clause Requirement + Test Result - Remark Verdict 6 Type test conditions Tests were made with the number of cells or batteries specified in Table 1 for nickel-cadmium and nickel-metal hydride systems and Table 2 for lithium systems, using cells or batteries that are not more than six months old Unless noted otherwise in the test methods, testing was conducted in an ambient of 20 C 5 C. Complied. Lithium system. Considered and evaluated for the batteries. 8 Specific requirements and tests (lithium systems) 8.1 Charging procedures for test purposes First procedure: This charging procedure applied to tests other than those specified in Discharge current: 1120 ma Moulded case stress at high ambient temperature (battery) See below. Oven temperature ( C)... : The batteries were fully charged and tested in the conditions of 70 C for 7 h. Results: No physical distortion of the battery casing resulting in exposure if internal components No physical distortion of battery case resulting in exposure of internal components Free fall The batteries were fully charged and tested for this condition. Results: No fire. No explosion. No fire, no explosion to the apparatus after the test. Beitou District, Taipei City, 11270, Taiwan age 7 of 8 Test Report IEC62133B

20 TABLE: Critical components information Object/part no. Revise components: Nameplate Marking Label - Material of Nameplate Marking Label - Adhesive for Nameplate Marking Label secure Enclosure Manufacturer/ trademark Cymmetrik Enterprise Co., Ltd. Sichuan Dongfang Insulating Material Co., Ltd 3M China Co., Ltd. Formosa Chemicals & Fibre Corp plastics Div. Supplementary information: Type/model Technical data Standard Mark(s) of conformity 1) CM V-0, 80 C thickness 0.1 mm DFD250B VTM-0, 105 C minimum thickness mm S C minimum thickness 0.05 mm AC3710 V-1, 80 C, 0.45 mm. thick minimum. UL 969 UL 94 UL 746C UL 969 UL 94 1) rovided evidence ensures the agreed level of compliance. See OD-CB2039. UL UL UL UL Beitou District, Taipei City, 11270, Taiwan age 8 of 8 Test Report IEC62133B