School of Technology, Energy & Apprenticeship. Advanced Power Engineering Program. Course Outline fall 2014
|
|
- Randell Cooper
- 5 years ago
- Views:
Transcription
1 School of Technology, Energy & Apprenticeship Advanced Power Engineering Program Course Outline fall 2014 Course Code: OES 7064 Course Title: Electrotechnology, Compression and Refrigeration Prepared By: Ashvinkumar C Bulsara Date: May 2014 Revised By: Dene Allen Date: October 2014 Approved By: Click here to enter name. Prerequisite: Co-requisite: Prerequisite for: Copyright 2014 Lambton College. All rights reserved. 1
2 1. Course Description The course includes a more advanced study of the theory of operation of electrical machines, and electrical distribution systems; leading into a detailed look at the construction and characteristics of AC and DC motors, generators, and other electrical equipment. The other major areas of study are principles, equipment and auxiliary systems with respect to gas compression systems and large scale refrigeration plants. Safety and code requirements are emphasized. This course utilizes the college advanced compressor and refrigeration simulation models through an online operating interface to reinforce operation and troubleshooting of these systems. 2. General Education and Essential Employability Skills This course provides the following provincial Essential Employability Skills: #1: Communication #2: Numeracy #3: Critical Thinking and Problem Solving #4: Information Management #5: Interpersonal #6: Personal Is this course approved as a General Education course? No 3. Learning Outcomes Yes Students should refer to their program s restricted General Education courses for final determination. Upon successful completion of this course, the learner will be able to: 1. Explain the principle of Alternate Current theory and significance of three phase AC circuits. 2. Explain the construction and operating principles of DC generators and motors. 3. Explain the construction and operating principles of Alternate Current (AC) generators. 4. Explain the construction and operating principles of AC motors. 5. Explain the construction and operating principles of transformers. 6. Describe the protective devices used on alternators, motors, and electrical circuits. 7. Explain the design and operation of gas compressors and compressed air system. Copyright 2014 Lambton College. All rights reserved. 2
3 8. Explain the construction and operation of refrigeration systems 9. Explain the procedures, standards, instrumentation, and controls for a refrigeration system 10. Perform refrigeration system calculations. 4. Course Objectives Learning Outcome Reference Number Unit 1 Electrotechnology: 1.1 Explain following term related to Alternating Current : [1] i. The sine wave: generation of an alternating electromotive force; root mean square values; vector representation of sinusoidal quantities, peak, peak to peak. ii. Resistance, inductance and capacitance in single-phase A.C. circuits; inductive reactance; capacitive reactance, impedance, resonance. iii. Power in A.C. circuits; true and apparent power; practical importance of power factor; power factor correction. iv. Three-phase circuits: delta and star connected alternators and loads, current and voltage relationships; three-phase power. 1.2 Calculate impedance, reactance, true and apparent power, [1] and power factor in AC Circuits. 1.3 Calculate phase voltage, phase current and apparent and [1] true power in a three-phase AC circuit. 1.4 Explain following term related to Direct Current Machines : [2] i. Generators: principle of operation; construction; commutation; armature reaction; interpoles; compensating windings; lap and wave wound armatures; generator types and characteristics; parallel operation; voltage regulation; theory of self-excitation; efficiency and power losses; Selection of generators and applications; parallel operation; ratings. ii. Motors: principle of motor action; torque development; Fleming s left-hand rule; back electromotive force: voltage, current and speed computation; motor types and characteristics; starting arrangements; dynamic and regenerative braking; speed control; efficiency and power losses. 1.5 Calculate torque, speed and current of a DC motors. [2] 1.6 Calculate efficiency and discuss the reasons for power losses in a DC motor and generator. [2] Copyright 2014 Lambton College. All rights reserved. 3
4 1.7 Explain following term related to Alternating Current Generators: i. Alternators: types; construction of stators, rotors and exciters; stator windings; relationship between speed, frequency and number of pole pairs; cooling systems; shaft sealing systems; voltage regulators; synchronizing; parallel operation; power factor control, voltage drops in armatures; rating, efficiency and power losses. ii. Single-phase motors: universal, shaded pole and splitphase types; repulsion-start and reluctance-start types; capacitance starting method. iii. Polyphase induction motors; principle of operation; rotating magnetic field; slip and rotor speed; stator and rotor construction; starting methods. iv. Synchronous motors: general facts concerning synchronous motors; stator and rotor construction, starting methods. v. Transformers: principle of transformer action; ratings; efficiency and losses; short and open circuit tests; types of construction; methods of cooling; connections; paralleling; instrument transformers. vi. Protection of electrical systems: alternator stator and rotor protection devices; motor protection devices; transformer safety fittings. vii. Circuit-protective equipment; interrupting capacity; fuses; switches; circuit-breakers; relays. 1.8 Calculate load, power, iron and copper losses, and efficiency in a transformer. Unit 2 Principles of Air and Gas Compression: 2.1 Describe the design and application of compressors including a selection of prime movers. 2.2 Explain various applications of air and gas compression and effects of altitude, temperature, and humidity. 2.3 Describe the design and operations of reciprocating, rotary and axial compressor. 2.4 Describe the installation of a compressed air system showing all ancillary equipment including typical instrumentation. 2.5 Describe the regulation and control of compressors. 2.6 Describe the monitoring and protection devices for a compressed air system. 2.7 Describe the monitoring, troubleshooting, and typical preventive maintenance for a compressed air system. Unit 3 Industrial/Commercial Refrigeration [3,5,6] [5] Copyright 2014 Lambton College. All rights reserved. 4
5 3.1 Describe the types of refrigerants. [10] 3.2 Describe the principles and operation of vapor [8] compression, absorption refrigeration, multi-stage and cascade refrigeration system. 3.3 Describe the principles, applications and operation of heat pump and thermoelectric cycle. [8] 3.4 Describe refrigerating plants layouts and installation details. [8,9] 3.5 Describe the design and operation of compressors; [8,9] condensers; evaporators; liquid receivers; oil separators; absorbers; generators; heat exchangers; rectifiers; driers; scale traps; piping and fittings; cold room construction. 3.6 Explain Operation of refrigerating plants, starting up and [8,9] shutting down; charging; hand and automatic purging; automatic expansion valves; compressor lubrication; brine solutions; leak testing; trouble shooting. 3.7 Describe the codes and standards which apply to the [8,9] design, installation, and operation of a refrigeration plant. 3.8 Describe the purpose and operation of the various [9] operating, actuating, limiting and safety controls used in refrigeration systems. 3.9 Computations of capacities and performances of [10] refrigerating plants; ideal and practical refrigerant cycles; theoretical piston displacement; heat pump effect; theoretical power; pressure-enthalpy charts 3.10 Describe the general refrigeration cycle and the application [10] of the Carnot cycle Define and calculate the refrigerating effect and the mass [10] of refrigerant circulated Calculate the coefficient of performance for a refrigeration [10] system Calculate the capacity of a refrigeration machine. [10] 3.14 Calculate the theoretical power of a refrigeration compressor Calculate the theoretical bore and stroke of a refrigeration compressor. 5. Resources and Supplies a. Required PanGlobal Training Systems Ltd. (2013). Power Engineering Second Class (1 st ed.). Calgary, AB: Author. b. Supplemental 6. Methodology [10] [10] Copyright 2014 Lambton College. All rights reserved. 5
6 This course utilizes the virtual classroom and resulting interactivity to prepare candidates to challenge the 2nd Class Power Engineering exam 2B3Entirely online due to theoretical nature of material. The Instructor led virtual classroom contains: Descriptive lecture notes based on course text Examples based on industry experience Sample questions and testing in preparation for SOPEEC exam Interactive with instructor and others in class within virtual classroom Video or simulation where applicable Use of simulation model for project planning exercise 7. Student Evaluation The following elements will determine the student s final grade: Electrotechnology Test 20% Principles of Air and Gas Compression Test 20% ttetesttest Industrial/Commercial Refrigeration Test 20% Comprehensive Exam 40% Total 100% The round off mathematical principle will be used. Percentages are converted to letter grades and grade points as follows: Mark (%) Grade Grade Point Mark (%) Grade Grade Point A C A C A C B D B F B Academic Integrity Lambton College is committed to high ethical standards in all academic activities within the College, including research, reporting and learning assessment (e.g. tests, lab reports, essays). The cornerstone of academic integrity and professional reputation is principled conduct. All scholastic and academic activity must be free of all forms of academic dishonesty, including copying, plagiarism and cheating. Lambton College will not tolerate any academic dishonesty, a position reflected in Lambton College policy. Students should make themselves familiar with the Students Rights and Responsibilities Policy, located on the MyLambton website for details concerning academic dishonesty and the penalties for dishonesty and unethical conduct. Copyright 2014 Lambton College. All rights reserved. 6
7 Questions regarding this policy, or requests for additional clarification, should be directed to the Lambton College Centre for Academic Integrity 9. Related Items Students with Disabilities If you are a student with a disability please identify your needs to the professor and/or the Accessibility Centre so that support services can be arranged for you. You can do this by making an appointment at the Accessibility Centre, Room L103 ext.3427 or by arranging a personal interview with the professor to discuss your needs. Student Rights and Responsibility Policy Acceptable behaviour in class is established by the instructor and is expected by all students. Any form of harassment or violence will not be tolerated. Action will be taken as outlined in Lambton College policy. Cheating and plagiarism are serious academic offences subject to disciplinary action. It is the student s responsibility to be aware of the cheating policy as described in the Lambton College Student Rights and Responsibilities policy. For further information on all of these policies, links may be found on the Lambton College website. Prior Learning Assessment Statement This course is eligible for Prior Learning Assessment Yes No If yes has been selected, you may choose to contact the Counselling Department for advice on Prior Learning Assessment. Date of Withdrawal without Academic Penalty Please consult the Academic Regulations and Registrar's published dates. Waiver of Responsibility Every attempt has been made to ensure the accuracy of this information as of the date of publication. The content may be modified, without notice, as deemed appropriate by the College. Note: It is the student s responsibility to retain course outlines for possible future use to support applications for transfer of credit to other educational institutions. Copyright 2014 Lambton College. All rights reserved. 7
SQA Advanced Unit specification: general information
SQA Advanced Unit specification: general information Unit title: Electrical Machine Principles Unit code: HT83 47 Superclass: XJ Publication date: August 2017 Source: Scottish Qualifications Authority
More informationELECTRICAL MACHINES. Theory and Practice. M.N. Bandyopadhyay
ELECTRICAL MACHINES Theory and Practice M.N. Bandyopadhyay ELECTRICAL MACHINES Theory and Practice M.N. Bandyopadhyay Director National Institute of Technology Kurukshetra Delhi-110092 2014 ELECTRICAL
More informationHigher National Unit Specification. General information for centres. Electrical Motors and Motor Starting. Unit code: DV9M 34
Higher National Unit Specification General information for centres Unit title: Electrical Motors and Motor Starting Unit code: DV9M 34 Unit purpose: This Unit has been developed to provide candidates with
More informationAuto Service Technician
Auto Service Technician Organization Washburn Institute of Technology Program Number 47.0604 Instructional Level Certificate Target Population Grades 11 & 12 Post-secondary Description The Auto Service
More informationAcademic Course Description
BEE305- ELECTRICAL MACHINES Academic Course Description BHARATH UNIVERSITY Faculty of Engineering and Technology Department of Electrical and Electronics Engineering BEE305- ELECTRICAL MACHINES Third Semester,
More informationContents. Review of Electric Circuitd. Preface ;
Preface ; Chapter 1 Review of Electric Circuitd 1.1 Introduction, 1 1.2 Direct Circuit Current, 1 1.2.1 Voltage, 3 1.2.2 Power, 3 1.2.3 Ohm's Law, 5 1.2.4 KirchhofTs Laws, 5 1.2.4.1 Kirchhoff s Current
More informationDEPARTMENT OF EI ELECTRICAL MACHINE ASSIGNMENT 1
It is the mark of an educated mind to be able to entertain a thought without accepting it. DEPARTMENT OF EI ELECTRICAL MACHINE ASSIGNMENT 1 1. Explain the Basic concepts of rotating machine. 2. With help
More informationELEC 585/462 MOTOR DRIVE DYNAMICS COURSE OUTLINE & ASSESSMENT TECHNIQUES SEPT- DEC / FALL 2013 CRN 11254/11246
ELEC 585/462 MOTOR DRIVE DYNAMICS COURSE OUTLINE & ASSESSMENT TECHNIQUES SEPT- DEC / FALL 2013 CRN 11254/11246 Instructor: Office Hours: Dr. S. Nandi Days: Any time by appointment Phone: 721-8679 Location:
More informationDC CIRCUITS ELECTROMAGNETISM
DC CIRCUITS 1. State and Explain Ohm s Law. Write in brief about the limitations of Ohm s Law. 2. State and explain Kirchhoff s laws. 3. Write in brief about disadvantages of series circuit and advantages
More informationScope for Electrical Machine Design. Objectives. Design and Engineering. Course Description. 23-Dec-16 DESIGN OF ELECTRICAL MACHINES AN OVERVIEW
SNS COLLEGE OF ENGINEERING (Accredited by NAAC-UGC with A Grade, Approved by AICTE, Recognized by UGC and Affiliated to Anna University, Chennai) COIMBATORE 641 107 DEPARTMENT OF ELECTRICAL AND ELECTRONICS
More information1. (a) If a large power generating station is operating with steam at 16,000 kpa and 500 and exhausting to a condenser at, 37.6 mm mercury absolute;
Sample Questions REVISED SECOND CLASS PARTS B1, B2, AND B3 (NOTE: these questions are intended as representations of the style of questions that may appear on examinations, they are not intended as study
More informationUNIT-I ALTERNATORS PART-A
UNIT-I ALTERNATORS 1. What principle is used in Alternators? 2. What are the requirements of an alternator? 3. Mention the types of alternator rotor. 4. What is hunting in alternators? 5. What are the
More informationGUJARAT TECHNOLOGICAL UNIVERSITY, AHMEDABAD, GUJARAT. Course Curriculum. D C MACHINES AND TRANSFORMERS (Code: ) Electrical Engineering
GUJARAT TECHNOLOGICAL UNIVERSITY, AHMEDABAD, GUJARAT Course Curriculum D C MACHINES AND TRANSFORMERS (Code: 3330902) Diploma Programme in which this course is offered Semester in which offered Electrical
More informationHigher National Unit Specification. General information for centres. Electrical Motor Drive Systems. Unit code: DN4K 35
Higher National Unit Specification General information for centres Unit code: DN4K 35 Unit purpose: This Unit has been designed to allow candidates to develop a knowledge and understanding of electrical
More informationPermanent Magnet DC Motor
Renewable Energy Permanent Magnet DC Motor Courseware Sample 86357-F0 A RENEWABLE ENERGY PERMANENT MAGNET DC MOTOR Courseware Sample by the staff of Lab-Volt Ltd. Copyright 2011 Lab-Volt Ltd. All rights
More informationElectrical Machines. Unit level 4 Credit value 15. Introduction. Learning Outcomes
Unit 21: Unit code Electrical Machines A/615/1495 Unit level 4 Credit value 15 Introduction Electrical machines can be found in manufacturing, transport, consumer appliances and hospitals. People will
More informationJEFFERSON COLLEGE COURSE SYLLABUS HRA101 ELECTRICITY FOR HVAC. 5 Credit Hours. Prepared by: William Kaune. Revised Date: March 17, 2014
JEFFERSON COLLEGE COURSE SYLLABUS HRA101 ELECTRICITY FOR HVAC 5 Credit Hours Prepared by: William Kaune Revised Date: March 17, 2014 Dena McCaffrey, Ed.D., Dean, Career & Technical Education HRA101 Electricity
More informationToronto, Ontario, Canada
Toronto, Ontario, Canada SCHOOL: DEPARTMENT: PROGRAM (If applicable): COURSE TITLE: COURSE CODE: TOTAL COURSE HOURS: PRE-REQUISITES/CO-REQUISITES: COURSE ELIGIBILITY FOR PRIOR LEARNING ASSESSMENT AND RECOGNITION
More informationElectrical Equipment and Safety: Operation, Control, Maintenance and Troubleshooting
Electrical Equipment and Safety: Operation, Control, Maintenance and Troubleshooting Page 1 of 6 Why Attend This course covers the theoretical and practical operation of common electrical equipment and
More informationToronto, Ontario, Canada
Toronto, Ontario, Canada SCHOOL: DEPARTMENT: PROGRAM (If applicable): COURSE TITLE: COURSE CODE: TOTAL COURSE HOURS: PRE-REQUISITES/CO-REQUISITES: COURSE ELIGIBILITY FOR PRIOR LEARNING ASSESSMENT AND RECOGNITION
More informationIndustrial Substation Maintenance April $4,250 Abu Dhabi. UAE
Training Title INDUSTRIAL SUBSTATION MAINTENANCE Training Duration 5 days Training Venue and Dates Industrial Substation Maintenance 5 19 23 April $4,250 Abu Dhabi. UAE Training will be held at any 5 Star
More informationSSC-JE STAFF SELECTION COMMISSION ELECTRICAL ENGINEERING STUDY MATERIAL ELECTRICAL MACHINES
1 SSC-JE STAFF SELECTION COMMISSION ELECTRICAL ENGINEERING STUDY MATERIAL 28-B/7, Jia Sarai, Near IIT, Hauz Khas, New Delhi-110016. Ph. 011-26514888. www.engineersinstitute.com 2 CONTENT 1. : DC MACHINE,
More informationAerial Operations. Name: Frank Ennist
DEPARTMENT OF FINANCIAL SERVICES Division of State Fire Marshal Bureau of Fire Standards & Training Title: Master Syllabus Date: October 3, 2017 Aerial Operations Course Title Aerial Apparatus Operations
More informationScheme - I. Sample Question Paper
Program Name Program Code Course Title Sample Question Paper : Diploma in Industrial Electronics : IE : Electrical Machines and Transformers Max. Marks : 70 Time : 3 Hrs. Q1. ATTEMPT ANY FIVE OF THE FOLLOWING.
More informationSYLLABUS. osmania university UNIT - I UNIT - II UNIT - III UNIT - IV CHAPTER - 1 : PRINCIPLES OF ELECTRO-MECHANICAL ENERGY CONVERSION CHAPTER - 2 :
i UNIT - I SYLLABUS osmania university UNIT - II CHAPTER - 1 : PRINCIPLES OF ELECTRO-MECHANICAL ENERGY CONVERSION Energy in Magnetic System, Field Energy and Mechanical Force, Direction of Mechanical Force
More informationITT Technical Institute. ET3480T Power Systems Onsite Course SYLLABUS
ITT Technical Institute ET3480T Onsite Course SYLLABUS Credit hours: 4.5 Contact/Instructional hours: 67 (41 Theory Hours, 26 Lab Hours) Prerequisite(s) and/or Corequisite(s): Prerequisites: ET3380T Power
More informationGUJARAT TECHNOLOGICAL UNIVERSITY, AHMEDABAD, GUJARAT COURSE CURRICULUM. Course Title: D C MACHINES AND TRANSFORMER (Code: )
GUJARAT TECHNOLOGICAL UNIVERSITY, AHMEDABAD, GUJARAT COURSE CURRICULUM Course Title: D C MACHINES AND TRANSFORMER (Code: 3330902) Diploma Programme in which this course is offered Electrical Engineering
More informationINSTITUTE OF AERONAUTICAL ENGINEERING Dundigal, Hyderabad
INSTITUTE OF AERONAUTICAL ENGINEERING Dundigal, Hyderabad - 500 043 MECHANICAL ENGINEERING ASSIGNMENT Name : Electrical and Electronics Engineering Code : A40203 Class : II B. Tech I Semester Branch :
More informationElectrical Systems and Fault Finding
Unit 31: Unit code Electrical Systems and Fault Finding A/615/1500 Unit level 4 Credit value 15 Introduction Electrical systems can be found in a very wide range of locations such as in manufacturing facilities,
More informationElectrical and Telecommunications Engineering Technology_EET2251/ET452. Electrical and Telecommunications Engineering Technology
YORK CITY COLLEGE OF TECHNOLOGY The City University of New York DEPARTMENT: SUBJECT CODE AND TITLE: Electrical and Telecommunications Engineering Technology EET2251/ET452 Electric Machines Laboratory COURSE
More informationDEPARTMENT OF ELECTRICAL AND ELECTRONICS ENGINEERING
DEPARTMENT OF ELECTRICAL AND ELECTRONICS ENGINEERING QUESTION BANK 16EET41 SYNCHRONOUS AND INDUCTION MACHINES UNIT I SYNCHRONOUS GENERATOR 1. Why the stator core is laminated? 2. Define voltage regulation
More informationAlternating Current Machines SAMPLE. Learner Workbook. Version 1. Training and Education Support Industry Skills Unit Meadowbank. Product Code: 5633
Learner Workbook Version 1 Training and Education Support Industry Skills Unit Meadowbank Product Code: 5633 Contents Introduction... 5 Section 1: Operating Principles of Three-Phase Induction Motors.7
More informationSingle Phase Induction Motors
Single Phase Induction Motors Prof. T. H. Panchal Asst. Professor Department of Electrical Engineering Institute of Technology Nirma University, Ahmedabad Introduction As the name suggests, these motors
More informationRegulation: R16 Course & Branch: B.Tech EEE
SIDDHARTH GROUP OF INSTITUTIONS :: PUTTUR Siddharth Nagar, Narayanavanam Road 517583 QUESTION BANK (Descriptive) Subject with Code : Electrical Machines-II (16EE215) Regulation: R16 Course & Branch: B.Tech
More information14 Single- Phase A.C. Motors I
Lectures 14-15, Page 1 14 Single- Phase A.C. Motors I There exists a very large market for single-phase, fractional horsepower motors (up to about 1 kw) particularly for domestic use. Like many large volume
More informationNZQA registered unit standard version 3 Page 1 of 5. Demonstrate and apply knowledge of electrical machines
Page 1 of 5 Title Demonstrate and apply knowledge of electrical machines Level 5 Credits 15 Purpose This unit standard covers knowledge and the application of d.c. and a.c. electrical machines for engineers.
More informationUnit 32 Three-Phase Alternators
Unit 32 Three-Phase Alternators Objectives: Discuss the operation of a three-phase alternator. Explain the effect of rotation speed on frequency. Explain the effect of field excitation on output voltage.
More informationCENTRAL TEXAS COLLEGE AERM 1445 AIRCRAFT ELECTRICAL SYSTEMS-A. Semester Hours Credit: 4 INSTRUCTOR: OFFICE HOURS:
A. INTRODUCTION CENTRAL TEXAS COLLEGE AERM 1445 AIRCRAFT ELECTRICAL SYSTEMS-A Semester Hours Credit: 4 INSTRUCTOR: OFFICE HOURS: A. An aviation maintenance technician must understand the basic electrical
More informationIn any of the 5 star hotels. The exact venue will be informed once finalized.
Training Title ELECTRIC DISTRIBUTION SYSTEM EQUIPMENT: Transformers, Switchgears, Circuit Breakers, Relays, Capacitors, Surge Arresters, Cables & Meters: Operation, Inspection, Testing, Evaluation, Maintenance
More informationAUT 163 AUTOMOTIVE FUNDAMENTALS SYLLABUS
Instructor: Office: Jeremy Akin AUT 163 AUTOMOTIVE FUNDAMENTALS SYLLABUS Automotive office in Career -Tech Bldg. Phone: 989-275-5000 Ext. 356 Email: Jeremy.Akin@kirtland.edu Required Text: Modern Automotive
More informationIAE-101: Electrical Fundamentals for Non-Electrical Personnel
IAE-101: Electrical Fundamentals for Non-Electrical Personnel Abstract Today s world of rapidly evolving technology poses a wealth of challenges just to remain competitive in the marketplace. Everyone
More informationCENTRAL TEXAS COLLEGE AERM 1314 BASIC ELECTRICITY-G Semester Hours Credit: 3 INSTRUCTOR: OFFICE HOURS:
I. INTRODUCTION CENTRAL TEXAS COLLEGE AERM 1314 BASIC ELECTRICITY-G Semester Hours Credit: 3 INSTRUCTOR: OFFICE HOURS: A. Electricity is a vital part of modern aviation technology. This course lays the
More informationBrake Test On Three Phase Induction Motor Lab Manual
Brake Test On Three Phase Induction Motor Lab Manual Electrical engineering machine lab manual. Brake test on three phase squirrel cage induction motor. No-load &, blocked rotor tests on three phase Slip.
More informationEE069: Electrical Engineering for Non-Electrical Engineers
EE069: Electrical Engineering for Non-Electrical Engineers EE069 Rev.002 CMCT COURSE OUTLINE Page 1 of 5 Training Description: This course introduces the Basic Principles of Electricity in a simple, easy
More informationCENTRAL MAINE COMMUNITY COLLEGE Auburn, ME Course Syllabus
CENTRAL MAINE COMMUNITY COLLEGE Auburn, ME 04210 Automotive Technology Term: Spring 18 AUT 292 Computerized Chassis Controls Instructor: Carl Hinkley Course Syllabus Course_Description This course will
More informationELECTRIC DRIVES N.K. DE P.K. SEN
ELECTRIC DRIVES N.K. DE P.K. SEN Electric Drives NISIT K. DE Associate Professor Department of Electrical Engineering Indian Institute of Technology Kharagpur and PRASANTA K. SEN Assistant Professor Department
More informationA Electric Power / Controls ELECTRIC POWER TECHNOLOGY 0.2 kw
A Electric Power / Controls ELECTRIC POWER TECHNOLOGY 0.2 kw TRAINING SYSTEMS, Shown with optional equipment. The production of energy using renewable natural resources such as wind, sunlight, rain, tides,
More informationBASIC PUMP TECHNOLOGY
Training Title BASIC PUMP TECHNOLOGY Training Duration 5 days Training Venue and Dates REF Basic Pump Technology ME039 5 20 24 October, 2019 $4,250 Dubai, UAE In any of the 5 star hotel. The exact venue
More informationUnit 34 Single-Phase Motors
Unit 34 Single-Phase Motors Objectives: Unit 34 Single-Phase Motors List the different types of split-phase motors. Discuss the operation of split-phase motors. Reverse the direction of rotation of a splitphase
More informationBasic Electrical Engineering
Basic Electrical Engineering Basic Electrical Engineering Revised Edition Dr. K Uma Rao Professor, Department of Electrical Engineering, R V College of Engineering, Bangalore Dr.A.Jayalakshmi AssociateProfessor,
More informationSYNCHRONOUS GENERATOR (ALTERNATOR)
i SYLLABUS osmania university UNIT - I SYNCHRONOUS MACHINES Constructional Details, Types of Windings, Winding Factors, EMF Equation, Fractional Pitch and Fractional Slot Windings, Suppression of Harmonics
More informationSIDDHARTH GROUP OF INSTITUTIONS :: PUTTUR
SIDDHARTH GROUP OF INSTITUTIONS :: PUTTUR Siddharth Nagar, Narayanavanam Road 517583 QUESTION BANK (DESCRIPTIVE) Subject with Code : ET(16EE212) Year & Sem: II-B.Tech & II-Sem UNIT I DC GENERATORS Course
More informationSAULT COLLEGE OF APPLIED ARTS AND TECHNOLOGY SAULT STE. MARIE, ONTARIO COURSE OUTLINE CODE NO. : MPT 230 SEMESTER: 4
SAULT COLLEGE OF APPLIED ARTS AND TECHNOLOGY SAULT STE. MARIE, ONTARIO COURSE OUTLINE COURSE TITLE: Air Brakes CODE NO. : MPT 230 SEMESTER: 4 PROGRAM: AUTHOR: Motive Power Technician Advanced Repair George
More informationElectrical Controls. Syllabus
Instructor: Jeremie Hedges (757)651-1007 Contact Hours: 72 hours Prerequisites: None Electrical Controls Syllabus Course Description: This course is designed to present a blend of electrical theory and
More informationWorkforce Development Learning Center Course Outline. Emergency Vehicle Driving FIP 3601
Revision Date: Workforce Development Learning Center Course Outline Course Title: A maximum of 30 values Course Number: State-assigned number Course Objectives: List the primary learning objectives Emergency
More informationThe Wound-Rotor Induction Motor Part I
Experiment 1 The Wound-Rotor Induction Motor Part I OBJECTIVE To examine the construction of the three-phase wound-rotor induction motor. To understand exciting current, synchronous speed and slip in a
More informationEEE3441 Electrical Machines Department of Electrical Engineering. Lecture. Introduction to Electrical Machines
Department of Electrical Engineering Lecture Introduction to Electrical Machines 1 In this Lecture Induction motors and synchronous machines are introduced Production of rotating magnetic field Three-phase
More informationDepartment of Electrical and Computer Engineering
Page 1 of 1 Faculty of Engineering, Architecture and Science Department of Electrical and Computer Engineering Course Number EES 612 Course Title Electrical Machines and Actuators Semester/Year Instructor
More informationUniversity of New South Wales School of Electrical Engineering & Telecommunications ELEC ELECTRIC DRIVE SYSTEMS.
Aims of this course University of New South Wales School of Electrical Engineering & Telecommunications ELEC4613 - ELECTRIC DRIVE SYSTEMS Course Outline The aim of this course is to equip students with
More informationSECTION 4 ELECTRIC MOTORS UNIT 17: TYPES OF ELECTRIC MOTORS UNIT OBJECTIVES UNIT OBJECTIVES 3/21/2012
SECTION 4 ELECTRIC MOTORS UNIT 17: TYPES OF ELECTRIC MOTORS UNIT OBJECTIVES After studying this unit, the reader should be able to Describe the different types of open single-phase motors used to drive
More informationDemonstrate knowledge of electrical theory for Electrical Service Technician B
Demonstrate knowledge of electrical theory for Electrical Service Technician B 10937 version 4 Page 1 of 5 Level 3 Credits 3 Purpose 'Electrical Service Technician B' (EST B) refers to a class of electrical
More informationELECTRICAL TECHNOLOGY 3 March 2008
I. Course Description ELECTRICAL TECHNOLOGY 3 March 2008 The purpose for this course is to instruct potential electricians in the skills necessary for entry into the job market. During this course, the
More informationJEFFERSON COLLEGE COURSE SYLLABUS AUT131 AUTOMOTIVE BRAKE SYSTEMS. 2 Credit Hours. Prepared by: Gerard Uhls Date: November 2011
JEFFERSON COLLEGE COURSE SYLLABUS AUT131 AUTOMOTIVE BRAKE SYSTEMS 2 Credit Hours Prepared by: Gerard Uhls Date: November 2011 Revised by: Gerard Uhls Date: September 12, 2016 Chris DeGeare, M.Ed., Division
More informationThree-Phase Motors and Drives
Unit 63: Three-Phase Motors and Drives Unit code: QCF Level 3: Credit value: 10 Guided learning hours: 60 Aim and purpose K/600/7117 BTEC Nationals This unit aims to give learners knowledge of three-phase
More informationDEM241 Advanced Diesel Engines
DEM241 Advanced Diesel Engines Course Information Credits 5 Campus Washburn Institute of Technology Address 5724 SW Huntoon City/State/Zip Topeka, Kansas 66604 Office Fax 785-273-7080 Description Advanced
More informationStarting of Induction Motors
1- Star Delta Starter The method achieved low starting current by first connecting the stator winding in star configuration, and then after the motor reaches a certain speed, throw switch changes the winding
More informationRequired Textbook and Materials 1. Texas Commercial Vehicle Drivers Handbook 2. Handout literature
Commercial Drivers License (CVOP 1201) Credit: 2 semester credit hours (1 hour lecture, 4 hours lab) Co-requisite: LNWK 1311 Course Description Overview of the State of Texas Class A Commercial Drivers
More informationDEM241 Advanced Diesel Engines
DEM241 Advanced Diesel Engines Course Information Credits 5 Campus Washburn Institute of Technology Address 5724 SW Huntoon City/State/Zip Topeka, Kansas 66604 Office Fax 785-273-7080 Description Advanced
More informationUNC-Charlotte's Power Engineering Teaching lab
1 UNC-Charlotte's Power Engineering Teaching lab B. Chowdhury Panel Session Title: Existing and Proposed Power Systems Laboratories for the Undergraduate Curriculum PES GM 2015 2 Outline Background - Energy
More information-SQA-SCOTTISH QUALIFICATIONS AUTHORITY HIGHER NATIONAL UNIT SPECIFICATION GENERAL INFORMATION
-SQA-SCOTTISH QUALIFICATIONS AUTHORITY HIGHER NATIONAL UNIT SPECIFICATION GENERAL INFORMATION -Unit Number- 2460957 -Superclass- -Title- XJ BRUSHLESS DC AND STEPPER MOTORS -----------------------------------------
More informationESO 210 Introduction to Electrical Engineering
ESO 210 Introduction to Electrical Engineering Lectures-37 Polyphase (3-phase) Induction Motor 2 Determination of Induction Machine Parameters Three tests are needed to determine the parameters in an induction
More informationME2301 THERMAL ENGINEERING L T P C OBJECTIVE:
ME2301 THERMAL ENGINEERING L T P C 3 1 0 4 OBJECTIVE: To integrate the concepts, laws and methodologies from the first course in thermo dynamics into analysis of cyclic processes To apply the thermodynamic
More informationDepartment of Technology Fall 2004
Department of Technology Fall 2004 EET 352 ELECTRICAL POWER TECHNOLOGY Instructor: Prof. Vigs Chandra, Ph.D. Telephone: 859-622-1187 E-mail: vigs.chandra@eku.edu Web: http://www.technology.eku.edu/facstaff/chandra/
More informationUNIT I D.C. MACHINES PART A. 3. What are factors on which hysteresis loss? It depends on magnetic flux density, frequency & volume of the material.
EE6352-ELECTRICAL ENGINEERING AND INSTRUMENTATION UNIT I D.C. MACHINES PART A 1. What is prime mover? The basic source of mechanical power which drives the armature of the generator is called prime mover.
More informationSAULT COLLEGE OF APPLIED ARTS AND TECHNOLOGY SAULT STE. MARIE, ON COURSE OUTLINE
SAULT COLLEGE OF APPLIED ARTS AND TECHNOLOGY SAULT STE. MARIE, ON COURSE OUTLINE COURSE TITLE: ELECTRICAL, ELECTRONICS & FUELS : SEMESTER: 32 Week Program PROGRAM: MOTOR VEHICLE MECHANIC PRE-APPRENTICE
More informationAUTO 140A: VEHICLE MAINTENANCE
AUTO 140A: Vehicle Maintenance 1 AUTO 140A: VEHICLE MAINTENANCE Discipline AUTO - Automotive Technology Course Number 140A Course Title Vehicle Maintenance Catalog Course Description Intended for the incumbent
More informationPREVIEW ONLY. Course 106 INSTRUCTOR GUIDE. HVAC Systems Introduction and Overview. Module 1: Overview of Rail Car HVAC and General Safety Procedures
Course 106 HVAC Systems Introduction and Overview Module 1: Overview of Rail Car HVAC and General Safety Procedures INSTRUCTOR GUIDE Table of Contents CHECKLIST FOR INSTRUCTION... 3 SUPPLIES, AUDIO-VISUAL
More informationDate: Name: ID: LABORATORY EXPERIMENT NO. 8 INDUCTION MOTOR/GENERATOR 8-1
Date: Name: ID: LABORATORY EXPERIMENT NO. 8 INDUCTION MOTOR/GENERATOR 8-1 OBJECT 1. To determine the general performance of a squirrel motors 2. To observe the characteristics of induction generators.
More informationUNIT 2. INTRODUCTION TO DC GENERATOR (Part 1) OBJECTIVES. General Objective
DC GENERATOR (Part 1) E2063/ Unit 2/ 1 UNIT 2 INTRODUCTION TO DC GENERATOR (Part 1) OBJECTIVES General Objective : To apply the basic principle of DC generator, construction principle and types of DC generator.
More informationPrinciples of Doubly-Fed Induction Generators (DFIG)
Renewable Energy Principles of Doubly-Fed Induction Generators (DFIG) Courseware Sample 86376-F0 A RENEWABLE ENERGY PRINCIPLES OF DOUBLY-FED INDUCTION GENERATORS (DFIG) Courseware Sample by the staff
More informationDevelopment of Electrical Power System Simulator.
Development of Electrical Power System Simulator. G. Adedokun, M.Eng., MNSE, R.Eng. Department of Electrical/Electronics Engineering, Osun State College of Technology, Esa-Oke, Nigeria * E-mail: adedokun_gb@yahoo.com
More informationJEFFERSON COLLEGE COURSE SYLLABUS AUT151 AUTOMOTIVE ENGINE REPAIR. 1 Credit Hour. Prepared by: Gerard Uhls
JEFFERSON COLLEGE COURSE SYLLABUS AUT151 AUTOMOTIVE ENGINE REPAIR 1 Credit Hour Prepared by: Gerard Uhls Revised by: Gerard Uhls Date: October 24, 2013 Date: February 10, 2014 Date: September 16, 2016
More informationElectricity Course. Part B Course Outline
Electricity Course Rev. Date: 10/01/2002 By: R. Crompton Part B Course Outline Subject Area 0 Orientation 2.6 0.0 0.1 To the School 1.0 0.2 To the Course 1.0 0.3 To the 0.3 0.3 0.4 To Possible Emergencies
More informationELECTRIC MOTOR DRIVES
ELECTRIC MOTOR DRIVES Prof. M.S. BERDE Retd. Prof. Department of Electrical Engineering N.I.T. (formerly, MACT) Bhopal (MP) KP KHANNA PUBLISHERS 4575/15, ONKAR HOUSE, OPP. HAPPY SCHOOL DARYAGANJ, NEW DELHI-110002
More informationIndustrial Maintenance Technology Student Learning Outcomes
Industrial Maintenance Technology Student Learning Outcomes February, 2017 ~ f ) FDTC Curriculum Map Program: Industrial Maintenance Technology Course# Course Title Credits Hours Lecture Lab Program Outcomes
More informationJEFFERSON COLLEGE COURSE SYLLABUS AUT162 INTRODUCTION TO ENGINE PERFORMANCE LAB. 3 Credit Hours. Prepared by: Gerard Uhls and Gary Boyher
JEFFERSON COLLEGE COURSE SYLLABUS AUT162 INTRODUCTION TO ENGINE PERFORMANCE LAB 3 Credit Hours Prepared by: Gerard Uhls and Gary Boyher Revised by: Gerard Uhls and Gary Boyher Date: October 24, 2013 Date:
More informationSingle Phase Induction Motor. Dr. Sanjay Jain Department Of EE/EX
Single Phase Induction Motor Dr. Sanjay Jain Department Of EE/EX Application :- The single-phase induction machine is the most frequently used motor for refrigerators, washing machines, clocks, drills,
More informationRECIPROCATING ROTARY PUMPS & COMPRESSORS
Training Title RECIPROCATING ROTARY PUMPS & COMPRESSORS Training Duration 5 days Training Venue and Dates Reciprocating Rotary Pumps & Compressors 5 16-20 March $3,750 Dubai, UAE Training will be held
More informationCourse Name: POWER ELECTRONICS Course Code: EE603 Credit: 4
Course Name: POWER ELECTRONICS Course Code: EE603 Credit: 4 Prerequisites: Sl. No. Subject Description Level of Study 01 Basic Electronics p n junction, Diode, BJT, MOSFET 1 st Sem, 2 nd Sem 02 Circuit
More informationVALLIAMMAI ENGINEERING COLLEGE
VALLIAMMAI ENGINEERING COLLEGE SRM Nagar, Kattankulathur 603 203. DEPARTMENT OF ELECTRICAL AND ELECTRONICS ENGINEERING Question Bank EE6401 ELECTRICAL MACHINES I UNIT I: MAGNETIC CIRCUITS AND MAGNETIC
More informationHigh Voltage Electrician Training
High Voltage Electrician Training Contact us Today for a FREE quotation to deliver this course at your company?s location. https://www.electricityforum.com/onsite-training-rfq Our 2-Day High Voltage Electrician
More informationQCF level: 4 Credit value: 15
Unit 63: Electrical Power Unit code: H/601/1408 QCF level: 4 Credit value: 15 Aim This unit will develop learners understanding of electrical power systems and power distribution and the advantages and
More informationResearch on the Structure of Linear Oscillation Motor and the Corresponding Applications on Piston Type Refrigeration Compressor
International Conference on Informatization in Education, Management and Business (IEMB 2015) Research on the Structure of Linear Oscillation Motor and the Corresponding Applications on Piston Type Refrigeration
More information(d) None of the above.
Dr. Mahalingam College of Engineering and Technology, Pollachi-3 (An Autonomous Institution affiliated to Anna niversity) CCET II (2016 Regulation) Name of Programme: B.E. (EEE) Course Code & Course Title:
More informationINTRODUCTION. AC motor operations, most widely used motor is three phase induction motor. This type of motor does not require any starting device
Modular Application (AC Motors) Engineering and Technical Teaching Equipment AEL-AI12 INTRODUCTION An electrical motor is such an electromechanical device which converts electrical energy into a mechanical
More informationDay 5 Practical and Written Final SAE Exams for SAE Int l Advanced HEV Diagnostics CoC
One of the fastest growing automotive sectors is the field of vehicles using electric propulsion systems. These technologies are providing significant opportunities and challenges to automotive instructors
More informationMotor-Generator and Transformer Construction Application AEL-MGTC
Engineering and Technical Teaching Equipment Motor-Generator and Transformer Construction Application AEL-MGTC INDUCTION MOTOR DISASSEMBLY ISO 9001: Quality Management (for Design, Manufacturing, Commercialization
More informationBELT-DRIVEN ALTERNATORS
CHAPTER 13 BELT-DRIVEN ALTERNATORS INTRODUCTION A generator is a machine that converts mechanical energy into electrical energy using the principle of magnetic induction. This principle is based on the
More informationPage 1. Design meeting 18/03/2008. By Mohamed KOUJILI
Page 1 Design meeting 18/03/2008 By Mohamed KOUJILI I. INTRODUCTION II. III. IV. CONSTRUCTION AND OPERATING PRINCIPLE 1. Stator 2. Rotor 3. Hall sensor 4. Theory of operation TORQUE/SPEED CHARACTERISTICS
More informationEngineering Diploma Resource Guide ST280 ETP Hydraulics (Engineering)
Engineering Diploma Resource Guide ST80 ETP Hydraulics (Engineering) Introduction Hydraulic systems are a fundamental aspect of engineering. Utilised across a variety of sectors including aviation, construction,
More information