Table of Contents

Transcription

1

2

3 Table of Contents Battery Installation 1 Charging Batteries 5 Mission Ready Checklist 17 Post-Mission Checklist 21 Remove Floatation Cover 23 Washing & Rinsing 27 Install Floatation Cover 29 Camera 35 How to operate How to charge Headlights 41 How to operate 41 Ground Station Setup 43 Power On the Ground Station 45 Check Connection to Ground Station 47 Configure Sonar System 49 Display Sonar Images 51 Sonar Post-Op Procedures 53 Charging the EMILY Sonar Batteries 55 Ground Station Disassembly 57

4

5 Battery Installation Check power plug is in at stern Remove hatch Hydronalix, Inc. 1

6 Loosen battery module strap Remove battery module case, disconnect battery module lead wires Hydronalix, Inc. 2

7 Reinstall fresh battery module and secure strap Reinstall hatch Hydronalix, Inc. 3

8

9 Charging Batteries Standard battery module Open case Hydronalix, Inc. 5

10 Disconnect all battery leads (Inside the battery module) Separate batteries Hydronalix, Inc. 6

11 Charger and cables Plug in IC Adaptor lead into charger Hydronalix, Inc. 7

12 Plug in battery connector leads into charger (red/black) Connect battery to IC Adaptor plug 3S Hydronalix, Inc. 8

13 Connect power lead to battery lead Plug power cord into charger Hydronalix, Inc. 9

14 Plug into wall outlet Charger screen will come on for Battery Check Press white button When you see 5.5A, press white button to select Hydronalix, Inc. 10

15 Press white button again When you see 11.1V(3S), press white button to select Whenchargerreads LipoCharge5Aand11.1V(3S),hold white button until you hear a beeping noise confirm Display will read Battery Check. Remove finger from white button Hydronalix, Inc. 11

16 Display will read Confirm or Cancel Press white button again to confirm: this begins charging When done, alarm will sound and the charger will read FULL Hydronalix, Inc. 12

17 Unplug power cord from wall Unplug power cord from charger Hydronalix, Inc. 13

18 Unplug battery IC Adapter lead Connect all batteries to case harness plugs Hydronalix, Inc. 14

19 Replace batteries in case Charged battery pack, Ready to go Hydronalix, Inc. 15

20

21 Mission Ready Checklist Check power plug is installed in stern (power off) Check and ensure cover string is pulled tight and tied to cleats Hydronalix, Inc. 17

22 Check Cover at bow (front)/ sides (ensure nose of boat is secure as shown and all 4 twist snap fasteners on the sides arelocked) Slide button to turn on remote control (transmitter) Hydronalix, Inc. 18

23 Check that voltage is OK, should be above 10.0 volts Ensure your finger is off the throttle control trigger Hydronalix, Inc. 19

24 RemoveEMILYlanyardpowerplugon stern to power on Test controls (Throttle- Motor should speed up, Steering- Water Jet on rear of boat should turn freely both left and right) Hydronalix, Inc. 20

25 Post- Mission Checklist Replace power plug in at stern Hydronalix, Inc. 21

26

27 Remove Floatation Cover Remove flagpole, can be stored inside cover by opening zipper Unclip two canvas twist snaps on each side Hydronalix, Inc. 23

28 Untie drawstring cleats Pull cover forward Hydronalix, Inc. 24

29 Disconnect battery and or remove Check for leakage or any issues Hydronalix, Inc. 25

30

31 Washing & Rinsing Removing saltwater, sand, and dirt by rinsing will prolong the life of your EMILY. Rinse water pump inlet and nozzle sections Rinse nozzle inside and out Hydronalix, Inc. 27

32 Rinse inside of boat thoroughly Flush water throughcooling system (Cooling water exhaust port under hose nozzle) Hydronalix, Inc. 28

33 Install Floatation Cover Pull Cover over bow Clip two canvas twist snaps on each side Hydronalix, Inc. 29

34 Starting on the right (star board) side of the boat place the loop on the over the left side of the cleat Wrap the loop around the cleat in a figure 8 pattern Hydronalix, Inc. 30

35 Warp around until it cannot wrap again. Make sure the red flap is under the cleat On the left (port) side of the boat, wrap the string around the palm of you hand and lift the boat to tighten the string Hydronalix, Inc. 31

36 Place the red flap under the cleat and wrap the string under and over the cleat a couple times Make a loop with the long string on the bottom and pull it over the cleat and pull tight. Repeat a few times Hydronalix, Inc. 32

37 Bring the string over to the right side and make a loop with the long string on the bottom and pull tight. Repeat until string is short and out of the way Install flagpole and spring base mount (Place flagpole in black spring base mount, align holes, slide hairpin cotter pin into the aligned holes to secure the flagpole) Hydronalix, Inc. 33

38

39 Camera How to operate Press and hold the power button on camera Download the FLIRFXapponmobiledeviceand connect to WiFi. For help please visit Press and hold the set up button until it beeps and orange WiFi symbol Hydronalix, Inc. 35

40 In your phones WiFi settings select the connection called FX-cameraname. Go back to FLIR FX app the camera will try to directly connect. Once the camera name shows up click on it. Hydronalix, Inc. 36

41 Once you are ready to record press the yellow recording button on the right and then record now. When ready to stop recording click the yellow recording circle and select stop recording. Hydronalix, Inc. 37

42 How to charge camera Remove camera from cover. Hydronalix, Inc. 38

43 Remove camera from sports case Plug Micro USB charging cable in to the camera Hydronalix, Inc. 39

44 Let charge. The Rec. will be red if charging. And turn green when done. Hydronalix, Inc. 40

45 Headlights How to operate Push the port side of the light to cycle through brightness settings. Low -> Medium -> High -> Off Hydronalix, Inc. 41

46

47 Ground Station Setup Check for DC power cable, AC power cable, and Comms antenna Connect the antenna into the Comms port Hydronalix, Inc. 43

48

49 Power On the Ground Station Connect power to the GS via AC or DC power AC Power DC Power Hydronalix, Inc. 45

50 Press the power button on the ION 10 Humminbird display and allow to initialize. Place the Sonar EMILY in the water and power on by pulling the mag switch inside the cover. Hydronalix, Inc. 46

51 Check Connection to Ground Station On the home screen of the ION 10, select: Settings -> Network -> Network Info Ensure that the SM2000 module is listed on the Humminbird network Hydronalix, Inc. 47

52

53 Configure Sonar System Under the Settings tab, select: Sonar -> Sonar Source -> 2D + DI + SI Ensure that 2D Sonar, SI Sonar, and DI Sonar are all active. Adjust the 2D and SI Frequency as needed Hydronalix, Inc. 49

54

55 Displaying Sonar Images Select the desired sonar pattern. Under Favorites on the home screen, Screen 1 is 2D imaging, Screen 2 is a map chart, Screen 3 is Side Imaging (SI), and Screen 4 is Down Imaging (DI) If desired, a screen with multiple displays can be created. Refer to the Humminbird User Guide for details. Hydronalix, Inc. 51

56

57 Sonar Post-Op Procedures Recover the Sonar EMILY and turn off both the sonar system and EMILY drive system Remove the Sonar EMILY cover from the boat Rinse the EMILY boat with fresh water and inspect for damage Remove the sonar paddle from the Sonar EMILY cover and store in a safe place Rinse the Sonar EMILY cover with fresh water and allow to dry Charge the batteries inside the cover if necessary Hydronalix, Inc. 53

58

59 Charging the EMILY Sonar Batteries Open the Velcro patch on the starboard side. Plug in the charging cable into the connector. On the battery charger, set the amperage limit to 2.0A and begin charging the battery pack. When charging is complete, disconnect the charging cable, replace the cap, and close the Velcro patch. Hydronalix, Inc. 55

60

61 Ground Station Disassembly Power off the ION 10 display Unplug the power cable from its source and stow inside the GS lid Unplug the Comms antenna and stow inside the GS lid Secure caps onto all connectors Close the GS lid Hydronalix, Inc. 57

62

63

64 Rev-A1-SON