Simple easy MD11 Manual Model No:OEM-06

Transcription

1 Simple easy MD11 Manual Model No:OEM-06 Scale EDF Radio control airplane Wingspan:1600mm All the parts & Kit UNDER SAFETY PRECAUTIONS This radio control is not a toy! Always keep this instruction manual ready on hand for quick reference. Assemble this kit only places out of children reach. First-time builders of EDF model should seek the advice of experienced modellers before beginning assembly and if they do not fully understand any parts of the construction. Taking out liability insurance is recommended. You are responsible for this model s assembly and safe operation. You need to purchase the following accessories power system separately to complete the model. FF3-311 Motor 2750kv 2pcs ESC 60A need wire long 500mm 2PCS FF9-902 SERVO 9g 9pcs FF9-911 Servo 17g 1pcs Battery 4S 35C mAh 2pcs FF14-04 Servo extension cable: 300mm 4pcs FF14-01 Servo extension cable: 600mm 2pcs FF14-03 Servo extension cable: 800mm 7pcs FF14-06 Y# extension cable: 300mm *6pcs FF14-02 Battery extension cable Page 1

2 (1). Installed The wings: need to preparing:9g Servos*6pcs (Flyfly item no:ff9-902) Servos extension cables 600mm*2pcs (Flyfly item no:ff14-01) Servos extension cables 300mm*2pcs (Flyfly item no:ff14-04) & 800mm*2pcs (Flyfly item no:ff14-03) Y# extension cable: 300mm *3pcs (FF no: FF14-06) Parts:Horns(No:LL04-406A/B),Hold serveos plywood,push robs(no:nn ),linkage Stoppers(No:FF12-05) After installed like this photos A/B Glue the hold Servos Plywood Used 4pcs screws Closed Servo cover, A/B Glue in to the Servo hold on the wings Screws 2pcs to lock horm and Linkage stopper Push rob After finish like this photo,adjust the elevators & Flaps after all is installed,then lock the Linkage stoppers,please remember the servo horn between the Linkage stoppers always Keep in a flat line (2). Installed The ESC: need to preparing:esc 60A wire need 500mm long & battery extension cable300mm*2pcs, Y# extension cable: 300mm *1pcs (FF no: FF14-06) Made a 10mm hold on the wings,like this photos ESC Wire across from here ESC Wire go out from here Page 2

3 (3). Installed The landing gear: need to preparing:landing gear item no:ff *plastic retract and 1pcs Alum retract, Landing gear extension cable size:300mm *2pcs( FF item No:FF14-04), Y# extension cable: 300mm *3pcs (FF no: FF14-06) Plastic retract used screws lock on the wings After finish like this photos (4). Connected together fuselage and the wings Wings put in to the fuselage Adjust the wood with Nut for lock the wings,please don't glue at this moment. Adjust the hole connected to fuselage Carbon pin φ6*30mm Adjust the hole connected to fuselage Carbon pin φ6*30mm Carbon pin φ 6*30mm Carbon Rob φ 12*450mm Copyright 2014 Flyfly hobby Designed and Manufactured by: Flyfly hobby Mfg. Web: Page 3

4 Belly cover on the wings After the wings lock on the fuselage,now you can glue, see this photos (5). Fusealge nose section Connected together fuselage tail section 4*25mm Screws 6pcs (6). Installed elevator: need to preparing 9g servos*2 pcs (FF item no:ff9-902) Servos extension cables 800mm*2 (Flyfly item no:ff14-03) Parts:Horns(FF item no:ll04-406a/b),push robs(ff item no:nn ),linkage Stoppers(FF item no: FF12-05) Alum rob(ff item no: NN21-008) Linkage Stoppers φ8*6*22mm Alum rob No:NN Linkage Stoppers Lock the servos Page 4

5 Put the elevetor in to the alum rob,like the photos. Used screws 4*10mm (Item no: NN ) Lock the elevator Used screws 4*10mm (Item no: NN ) Lock the elevator like this Horns Clevis Please Adjust correct angle befored lock the linkage stoppers Push rob (7). Installed Tail rudder: need to preparing 9g servos*1 pcs (FF item no:ff9-902) Servos extension cables 800mm*1(Flyfly item no:ff14-03) Parts: Rudder Hinges (FF item no:ff ),push robs(ff item no:nn ),linkage Stoppers(FF item no: FF12-05) Alum rob(ff item no: NN21-008),Horns(FF item no:ll04-406a/b) A/B Glue Rudder Hinges to the tail Linkage Stoppers After Glue Rudder Hinges to the tail like this Screws to lock Horns Copyright 2014 Flyfly hobby Web: Designed and Manufactured by: Flyfly hobby Mfg. Page 5

6 After finish like this photo,adjust the rudder after all is installed,then lock the Linkage stoppers, please remember the servo horn between the Linkage stoppers always Keep in a flat line Servo cover screws lock Turn on tail and used screws 4*25mm lock the tail Tail carbon 8*250mm Tail Cover drilling a hold uesd 4pcs screws lock (8). Installed the nose gear: Need 17g servos*1 pcs (FF item no:ff9-911),servos extension cables 800mm*2pcs (Flyfly item no:ff14-01),y# extension cable: 300mm *1pcs (FF no: FF14-06) Page 6

7 Metal soft wire across the turn gear pin to the likage stoppers Servo lock here 3*12mm screws 4pcs lock the gear Installed ducted fan need FF6-603 *2pcs,FF3-311 Motor 2750KV 2pcs Copyright 2014 Flyfly hobby Web: Designed and Manufactured by: Flyfly hobby Mfg. Page 7

8 Engine cowl Screws lock cover & rings A/B Glue the fan in to engine cowl Connected motor wire to the ESC ESC wire from here A/B Glue the engine cowl & 2 screws lock on the plywood (10). Installed wings tip and Battery position After glue 2pcs Pins put between the wing and wing tips,then A/B glue together Open the battery cover See the Battery tray Used magic tap lock battery Copyright 2014 Flyfly hobby Web: Designed and Manufactured by: Flyfly hobby Mfg. info@flyflyhobby.com Page 8

9 (11). Adjustment A A B B CG Position 240mm Copyright 2014 Flyfly hobby Designed and Manufactured by: Flyfly hobby Mfg. Web: info@flyflyhobby.com Page 9