Single Solar Panel Installation with Dual Output Controller Charging Two Battery Banks

Transcription

1 Single Solar Panel Installation with Dual Output Controller Charging Two Battery Banks On/off switch MC4 Connectors Attach controller to battery banks first and to solar panels second.

2 Single Solar Panel Installation with EP Tracer MPPT Controller Charging One Battery Bank MC4 connector 20 amp switch Note: If a battery monitor is installed, negative wire from controller should be connected to the house side of the battery monitor shunt, not the battery bank.

3 Two Solar Panels Wired in Parallel with Dual Output Controller Charging Two Battery Banks MC4 Tbranch Connectors On/off switch Attach controller to battery banks first and to solar panels second.

4 Two Solar Panels Wired in Parallel with Tracer MPPT Controller Charging a Single Battery Bank 21 MC4 Tbranch connector 20 amp switch Note: If a battery monitor is installed, negative wire from controller should be connected to the house side of the battery monitor shunt, not the battery bank.

5 Two Solar Panels Wired in Parallel with Two EP Tracer BN MPPT Controllers To temp sensor attached to battery

6 Two Solar Panels Wired in Parallel with Two EP Tracer BN Controllers With a Battery Monitor **Shunt for battery monitor Negative wires from controllers go to house side of shunt. To temp sensor attached to battery

7 Four Solar Panels Wired in Parallel with Two EP Tracer BN MPPT Controllers To temperature sensor attached to battery

8 Four Solar Panels Wired in Parallel with Two EP Tracer BN MPPT Controllers With a Battery Monitor **Shunt for battery monitor Negative wires from controllers go to house side of shunt. To temp sensor attached to battery

9 Four Solar Panels Wired in Parallel with One EP Tracer BN MPPT Controller 21 MC4 Tbranch connector Note: If a battery monitor is installed, negative wire from controller should be connected to the house side of the battery monitor shunt, not the battery bank.

10 Four Solar Panels Wired Two in Series and Group in Parallel with EP Tracer BN MPPT Controller MC4 connectors 21 MC4 Tbranch connector Note: If a battery monitor is installed, negative wire from controller should be connected to the house side of the battery monitor shunt, not the battery bank.

11 Three Solar Panels Wired in Parallel with EP Dual Output Controller Charging Two Battery Banks 31 MC4 Tbranch connector Note: If a battery monitor is installed, negative wire from controller should be connected to the house side of the battery monitor shunt, not the battery bank.

12 Three Solar Panels Wired in Parallel with One EP Tracer BN MPPT Controller 31 MC4 Tbranch connector Note: If a battery monitor is installed, negative wire from controller should be connected to the house side of the battery monitor shunt, not the battery bank.

13 Auxiliary 100 watt semiflexible panel Tracer MPPT solar controller Tbranch MC4 connectors Wiring diagram showing connection of an auxiliary 110 watt solar panel when extra power is needed.

14 Double Pull Double Throw Switch Boost Controller 24V Thruster Bank Tbranch MC4 connectors House Bank Starting Bank

15 4 55 Watt panels to one 20 amp Controller and 3 55 Watt panels 100 Watt to another 20 amp Controller 21 MC4 Tbranch Diagram shows only one wire for simplicity. There will be two, positive and negative.

16 4 55 Watt panels to one 20 amp Controller and 3 55 Watt panels 100 Watt to another 20 amp Controller 41 MC4 Tbranch 31 MC4 Tbranch 21 MC4 Tbranch Diagram shows only one wire for simplicity. There will be two, positive and negative.

17 6 55 Watt panels to one 20 amp Controller and 1 55 Watt panel 100 Watt to another 20 amp Controller Diagram shows only one wire for simplicity. There will be two, positive and negative. 21 MC4 Tbranch 41 MC4 Tbranch