FRIATHERM multi / FRIATHERM uni Push-fit system / Press-fit system for drinking water and heating networks

Transcription

1 fittings networks Fittings and accessories 9 Transitions, external thread, short 9 Union couplings, external thread 9 Flanges 9 FRIATHERM Component+ adhesive 10 Transition sleeves 11 s - 20 cm 11 FRIATHERM transitions flexible, external thread 12 Flat gaskets 13 Assembly instructions 13 FRIATHERM multi / FRIATHERM uni Push-fit system / Press-fit system for drinking water and heating networks Fittings and tools 14 Transitions, external thread 14 Tools for press-fit connections 14 8 FRIATEC GT Stand 01/2018

2 P P fittings Transitions, external thread, short for drinking water pipelines; produced according to DIN 8080 and 8079; with bonded connection for. Ref.No. d PN/SDR Type PU Order qty d 16 x 2, x R ½ 25/9,0 tin-coated brass 1 d 20 x 2, x R ½ 25/9,0 tin-coated brass 1 d 25 x 2, x R ¾ 25/9,0 tin-coated brass 1 d 32 x 3, x R 1 25/9,0 tin-coated brass 1 Union couplings, external thread for transitions from threaded connections of valves, equipment and pipes in drinking water pipelines; produced according to DIN 8080 and 8079; consisting of bonding sleeve, union nut (tin-coated brass), flat gasket (EPDM) and threaded nipple (tin-coated brass). Ref.No. d PN/SDR Thread union nut Type PU Order qty d 40 x 4, x R 1 ¼ 25/9,0 R 2 tin-coated brass 1 d 50 x 5, x R 1 ½ 25/9,0 R 2 ¼ tin-coated brass 1 d 63 x 7, x R 2 25/9,0 R 2 ¾ tin-coated brass 1 Flanges for transitions from threaded connections to valves, equipment and pipes in drinking water pipelines; produced according to DIN 8080 and 8079; consisting of standard flange, backing ring with bonding sleeve and flat gasket (fiber). Ref.No. d PN/SDR Holes Type PU Order qty d 40 x 4, /9,0 4 flat gasket 1 d 50 x 5, /9,0 4 flat gasket 1 d 63 x 7, /9,0 4 flat gasket 1 d 75 x 5, /13,6 4 flat gasket 1 d 90 x 6, /13,6 8 flat gasket 1 FRIATEC GT Stand 01/2018 9

3 fittings FRIATHERM Component+ adhesive for high-strength bonded joints, fittings and adapters. Ref.No. Type PU Order qty d g tin (125 ml) 1 d g tin (400 ml) 1 FRIATHERM fittings and TECEquickpipe pipes Establishing a press-fit welding joint Glued connections of TECEquickpipe pipes and fittings in s d16 to d90 can be made. For that the following conditions are to be fulfil: W our FRIATEC Component+ solvent cement is used exclusively W appropriate tools and materials are used W the pressure levels specified in the planning documentation of the installed TECEquickpipe network are observed at all times. Note: Combinations of TECEquickpipe fittings with pipes are not allowed. W cutting W Deburring W Surface and adhesive must be kept at 0 C during gluing process W Surface to be cleanded with grease-free cloth W Apply Component+ W Push parts together, W Allow to set for W 10 C 6 bar adjust and hold in place 2 minutes after 30 min for at least 5 seconds W 10 C 15 bar after 120 min W 10 C 15 bar after 240 min 10 FRIATEC GT Stand 01/2018

4 P fittings Transition from pipes d 15, d 22, d 28 to d 16, d20, d 25 d d Ref.No. 15/ / / d Ref.No d Ref.No. 16 x ½ x ½ x ¾ pipe from 1982 to 1989 transition sleeve pipe as from 1990 transitions, external thread, short Transition sleeves for outer diameters d 15, d 22, d 28 for transition to pipes produced until the year These pipes have had, compared to today's range (d 16, d 20, d 25), different outer diameters (d 15, d 22, d 28). Ref.No. d PU Order qty d 16 x 1, /16 1 d 22 x 2, /20 1 d 28 x 3, /25 1 s - 20 cm pipe sections 20 cm. Ref.No. DN d PN/SDR PU Order qty d 16 x 2, /9,0 1 d 20 x 2, /9,0 1 d 25 x 2, /9,0 1 FRIATEC GT Stand 01/

5 FRIATHERM transitions flexible FRIATHERM flexible (Polybuten-pipes) up to 1999 d d 16 x 2,0 20 x 2,3 16 x 2,2 20 x 2,8 FRIATHERM transitions flexible, external thread for transition to FRIATHERM flexible pipe Polybuten (PB); consisting of: d 16 mm transition 16 x ½; support bush 16 x 2,0 mm and 16 x 2,2 mm d 20 mm transition 20 x ½; support bush 20 x 2,3 mm and 20 x 2,8 mm d 16 x 2,0 d 16 x 2,2 d 20 x 2,3 d 20 x 2,8 Ref.No. d PU Order qty x ½ x ½ 1 Assembly instruction for FRIATHERM transitions flexible, external thread Note: A preparation of the pipe ends is not necessary due to the design of the support bush. 12 FRIATEC GT Stand 01/2018

6 spare parts Flat gaskets suitable for union couplings and valve connectors. Ref.No. d PU Euro/ unit ½ (da = 18, di = 14, s = 2) ¾ (da = 24, di = 17, s = 2) (da = 30, di = 21, s = 3) ¼ (da = 38, di = 27, s = 3) ½ (da = 44, di = 32, s = 3) (da = 55, di = 42, s = 3) ¼ (da = 62, di = 46, s = 3) ¾ (da = 78, di = 60, s = 3) 1 Classification flat gaskets Ref.No. Fitting connectors with Fitting connectors with Union couplings, external thread nal thread Union couplings, inter- bonded nipple bonded socket d 16 x R ½ d 20 x R ¾ d 16 x ¾ d 16 x R ½ d 16 x R ½ d 25 x R d 20 x R d 20 x R ½ d 20 x R ½ d 32 x R 1 ¼ d 25 x R 1 ¼ d 25 x R ¾ d 25 x R ¾ d 32 x R 1 ½ d 32 x R d 32 x R d 40 x R d 40 x R 1 ¼ d 40 x R 1 ¼ d 50 x R 2 ¼ d 50 x R 1 ½ d 50 x R 1 ½ d 63 x R 2 ¾ d 63 x R d 63 x R 2 assembly instructions cutting cutting s are generally cut by means of a roller pipe cutter or by a mitre saw. Only use roller pipe cutters suitable for plastic pipes. Do not use pipe scissors. Deburring Deburring Use reamers depending on the relevant s W Inside and outside chamfering tool d mm W Chamfering tool d mm Standard reamers/chamfering tools suitable for plastic pipes can be used FRIATEC GT Stand 01/