K-Resin SB Copolymer/Crystal Polystyrene Sheet Property Modification with High Impact Polystyrene
|
|
- Amberlynn Ball
- 5 years ago
- Views:
Transcription
1 Styrene-Butadiene Copolymers Plastics Technical Center Report #9 K-Resin SB Copolymer/Crystal Polystyrene Sheet Property Modification with High Impact Polystyrene INTRODUCTION. Many sheet extruders are using K-Resin styrene-butadiene copolymer in machine side blends with crystal polystyrene. The K-Resin provides excellent toughness, and the polystyrene provides rigidity and economics. As the amount of crystal polystyrene in the blend is increased, the impact properties and performance of the sheet are diminished. This study evaluates the effect on physical properties of the sheet when low levels of high impact polystyrene HIPS are added to the blend. PROCEDURE. K-Resin/crystal polystyrene blends containing % K-Resin were compared in this study. Chevron 371, with a nominal 18 MF, polystyrene resin was used in this trial. Dow s high impact polystyrene grade, XL-88, was chosen as the HIPS impact modifier. It is a nominal 5 melt flow and has a notched Izod impact strength of 3 ft-lbf/in. The level of HIPS in the blend ranged from.5 to %. Samples were prepared by dryblending of the components together then repelletizing the blend. One set of samples of the 5/5 blends was dryblended only to determine if there was a significant difference in sheet properties of compounded vs. noncompounded samples. The blended samples were extruded into mil sheet on a 3 1 / inch NRM extruder and injection molded into test specimens for evaluation of physical properties. These results are shown in the accompanying Tables 1 8. RESULTS. Sheet strength was measured by both falling dart and a modified gardner impact test method. The two tests yielded similar results. They showed a substantial increase in impact of all the sheet samples to which high impact polystyrene was added. At the lowest level of HIPS addition,.5%, significant improvement in sheet strength was achieved. However, sheet strength values did not increase much as higher levels of HIPS were added. This is highlighted in Figures 1 and. Haze values increased significantly as higher levels of HIPS were added. Sheet clarity remained good when.5% HIPS was added to the blend. The haze development was most easily seen in the thicker injection molded specimens (15 mils), and worst in blends containing higher levels of crystal polystyrene (See Figures 3 and ). The dryblended pellets and repelletized samples produced sheet with very similar impact properties. The haze values in the sheet were also very similar, but in the thicker injection molded specimen, the repelletized samples had better clarity. This is the result of better mixing in the sheet line than in the injection molding process. HIPS also demonstrated improving antiblocking characteristics of the blended sheet. This occurred at levels as low as.5% HIPS. 1
2 Styrene-Butadiene Copolymers Table 1 Properties of / K-Resin/GPPS mil Blended Sheet Modified with Dow XL 88 HIPS Property Haze, % Light Transmission, % Dart Drop, g/ in * 75 Tensile Yield, psi MD TD Tensile Break, psi MD TD Elongation, % MD TD Oil Bath Shrinkage, % MD TD Hunter, Color b b Modified Gardner Impact, cm/kg * Large variation Table Properties of 5/5 K-Resin/GPPS mil Blended Sheet Modified with Dow XL 88 HIPS Property Haze, % Light Transmission, % Dart Drop, g/ in Tensile Yield, psi MD TD Tensile Break, psi MD TD Elongation, % MD TD Oil Bath Shrinkage, % MD TD Hunter, Color b b Modified Gardner Impact, cm/kg
3 Table 3 Properties of / K-Resin/GPPS mil Blended Sheet Modified with Dow XL 88 HIPS Property Haze, % Light Transmission, % Dart Drop, g/ in Tensile Yield, psi MD TD Tensile Break, psi MD TD Elongation, % MD TD Oil bath Shrinkage, % MD TD Hunter, Color b b Modified Gardner Impact, cm/kg Table Properties of 5/5 K-Resin/GPPS mil Blended Sheet Modified with Dow XL 88 HIPS (Dry Blended Only) Property Haze, % Light Transmission, % Dart Drop, g/ in Tensile Yield, psi MD TD Tensile Break, psi MD TD Elongation, % MD TD Oil Bath Shrinkage, % MD TD Hunter, Color b b Modified Gardner Impact, cm/kg
4 Styrene-Butadiene Copolymers Table 5 / K-Resin/GPPS Blends Injection Molded Specimen Modified with Dow XL 88 HIPS Property Haze, % Light Transmission, % Tensile Yield, psi Elongation, % Flexural Modulus, psi 9,7 98,5 99,5 8,5 91, 9,5 Flexural Yield Strength, psi Notched Izod, RT, 1/8", ft-lbf/in Hunter, Color b b Flow Rate, g/1 min Table 5/5 K-Resin/GPPS Blends Injection Molded Specimen Modified with Dow XL 88 HIPS Property Haze, % Light Transmission, % Tensile Yield, psi Elongation, % Flexural Modulus, psi 319,5 31,1 31,9 3, Flexural Yield Sstrength, psi Notched Izod, RT, 1/8", ft-lbf/in Hunter, Color b b Flow Rate, g/1 min
5 Table 7 / K-Resin/GPPS Blends Injection Molded Specimen Modified with Dow XL 88 HIPS Property Haze, % Light Transmission, % Tensile Yield, psi Elongation, % Flexural Modulus, psi 31,5 337, 335,1 33,15 Flexural Yield Strength, psi Notched Izod, RT, 1/8", ft-lbf/in Hunter, Color b b Flow Rate, g/1 min Table 8 5/5 K-Resin/GPPS Blends Injection Molded Specimen Modified with Dow XL 88 HIPS (Dry Blended Only) Property Haze, % Light Transmission, % Tensile Yield, psi 5 75 Elongation, % Flexural Modulus, psi 31,5 31,75 315,5 31,1 Flexural Yield Strength, psi Notched Izod, RT, 1/8", ft-lbf/in Hunter, Color b b Flow Rate, g/1 min CONCLUSIONS. Low levels of high impact polystyrene can significantly improve sheet impact properties of K-Resin/crystal polystyrene blend sheet. The HIPS also strengthens the sheet across the transverse direction, which makes the sheet more resistant to breakage. Adding.5 % HIPS to the sheet is approximately equivalent to increasing the K-Resin content by more than 1%. The amount of haze in the sheet increases as the percentage of HIPS is increased. Most blends should contain less than 1% HIPS to maintain maximum part clarity. Precompounding of the HIPS into the blend did not offer advantages in either impact or clarity of the blended sheet. 5
6 Styrene-Butadiene Copolymers Figure 1 Dart Drop Test Sheet 1 K-RESIN/GPPS / BLEND 1 K-RESIN/GPPS 5/5 BLEND DART DROP, gm/ in DART DROP, gm/ in K-RESIN/GPPS / BLEND 1 K-RESIN/GPPS 5/5 DRY BLEND DART DROP, gm/ in DART DROP, gm/ in Figure Modified Gardner Sheet Impact MODIFIED GARDNER IMPACT, cm/kg K-RESIN/GPPS / BLEND MODIFIED GARDNER IMPACT, cm/kg K-RESIN/GPPS 5/5 BLEND MODIFIED GARDNER IMPACT, cm/kg K-RESIN/GPPS / BLEND MODIFIED GARDNER IMPACT, cm/kg K-RESIN/GPPS 5/5 DRY BLEND
7 Figure 3 Haze Percentage Sheet K-RESIN/GPPS / BLEND K-RESIN/GPPS 5/5 BLEND K-RESIN/GPPS / BLEND K-RESIN/GPPS 5/5 DRY BLEND Figure Haze Percentage Injection Molding K-RESIN/GPPS / BLEND K-RESIN/GPPS 5/5 BLEND K-RESIN/GPPS / BLEND 5. K-RESIN/GPPS 5/5 DRY BLEND
8 Styrene-Butadiene Copolymers
Texin 245 Covestro PUR Thermoplastic Polyurethane Elastomer (Polyester) Action Saturday, October 22, 2016 Units English Legend (Open) General Information Product Description Texin 245 resin is an aromatic
More informationThe above data are preliminary and are subject to change as additional data are developed on subsequent lots.
Zenite LCP Product Information liquid crystal polymer resin 30% Glass Reinforced Liquid Crystal Polymer Resin PRELIMINARY DATA Zenite 7130 is a 30% glass reinforced LCP resin having excellent toughness
More informationULTEM* 1010 Resin. SABIC Innovative Plastics - Polyether Imide. Actions. General Information. Product Description
ULTEM* 1010 Resin SABIC Innovative Plastics - Polyether Imide Actions General Information Product Description Transparent, enhanced flow Polyetherimide (Tg 217C). ECO Conforming, UL94 V0 and 5VA listing.
More informationAntifreeze Resistant Fatigue Resistant Gasoline Resistance Automotive Under the Hood ASTM D 4066 PA012G30 ASTM D 6779 PA012G30
Vydyne R530H Nylon resins are general purpose polyamide, heat stabilized, hydrolysis resistant, 30% glass fiber reinforced resins. Available in natural and black. It is specifically designed to maximize
More informationLAPOL HDT TECHNICAL BULLETIN
Raising the Heat Deflection Temperature of PLA LAPOL HDT TECHNICAL BULLETIN OCTOBER 2014 1 Polylactic Acid (PLA) The Front Runner in Bioplastics 100% degradable thermoplastic resin Made from renewable
More informationFusion Equipment & Tools Electrofusion Processor Scraper Tools Rerounding Tools Socket Fusion Kit
Fusion Equipment & Tools Electrofusion Processor Scraper Tools Rerounding Tools Socket Fusion Kit 71 I Fuse 105 Electrofusion Processor The IntegriFuse I Fuse 105 Electrofusion Processor is the next generation
More informationCrastin PBT Thermoplastic polyester resins
Crastin PBT Thermoplastic polyester resins Product guide and properties Start with DuPont Engineering Polymers DuPont s registered trademark Crastin PBT Thermoplastic polyester resins Introduction CRASTIN
More informationEconomic Benefits of Utilizing MDO Films in Flexible Packaging
Economic Benefits of Utilizing MDO Films in Flexible Packaging D. Ryan Breese Technical Director Eclipse Film Technologies 4434 Muhlhauser Rd. Suite 200 Hamilton, Ohio 45011 1-877-275-4800 rbreese@eclipsefilmtech.com
More informationRECYCLABILITY EVALUATION PROTOCOL FOR PE FILMS
Phone : +32 2 742 96 82 Fax : +32 2 732 12 18 e-mail : recyclass@plasticsrecyclers.eu website: www.recyclass.eu RECYCLABILITY EVALUATION PROTOCOL FOR PE FILMS Standard Laboratory Practice Version 1.0 Published
More informationTDI-terminated polyester based prepolymer
PRODUCT DATA VIBRATHANE 8080 TDI-terminated polyester based prepolymer Urethane Prepolymers VIBRATHANE 8080 VIBRATHANE 8080 is a TDI-terminated polyester based prepolymer which yields an 80 Shore A hardness
More informationEconomic Benefits of Utilizing MDO Films in Flexible Packaging
Economic Benefits of Utilizing MDO Films in Flexible Packaging D. Ryan Breese Technical Director Eclipse Film Technologies 4434 Muhlhauser Rd. Suite 200 Hamilton, Ohio 45011 1-877-275-4800 rbreese@eclipsefilmtech.com
More informationTECHNYL A 218 BLACK 21N
TECHNYL A 218 BLACK 21N Description TECHNYL A 218 Black 21 N is an unreinforced polyamide 66, standard viscosity, heat stabilized for injection moulding.it is available in black color. Key Properties Chemical
More informationTesting based on UL 1667 (Tall Institutional Carts for Audio, Video and TV-Type Equipment)
MEDICAL PRODUCT DESIGN AND MANUFACTURING 114 DOUGLAS ROAD EAST OLDSMAR, FLORIDA 34677 OFFICE: 813.889.9250 800.899.5278 FAX: 813.886.9342 WWW.PROMEDICA-USA.COM Risk Assessment and Testing Results for Promedica
More informationTECHNICAL DATA SHEET. Solmax HDPE Premium Smooth - Metric Values SPECIFICATIONS PROPERTY TEST FREQUENCY (1) UNIT. Solmax.
HDPE Premium Smooth - Metric Values International Inc., 2801 Boul. Marie-Victorin, Varennes, Qc, Canada, J3X 1P7 440-3100 460-3100 480-3100 500-3100 SPECIFICATIONS Thickness (min. avg.) ASTM D-5199 Thickness
More informationFossil-fuel resources becoming more costly: economically, environmentally & geopolitically.
Fossil-fuel resources becoming more costly: economically, environmentally & geopolitically. A need exists for sustainable, low-cost, bio-based feedstock in the renewable plastics industry. Diversion of
More informationPOLYETHYLENE High Density
POLYETHYLENE High Density PE-3408/PE-3608 ENGINEERED FOR WATER AND MINING PIPING SYSTEMS PLASTIC MANUFACTURES SINCE 1953 POLYTUBES HIGH MOLECULAR WEIGHT (HMW) High Density Polyethylene Pipe for General
More informationROLLER LUBRICANT VISCOSITY RATING
CHAIN INFORMATION OUTER PLATE OUTER PLATE PIN 2 PIECES OF EACH MAKE AN OUTER LINK BUSH INNER PLATE INNER PLATE 2 PIECES OF EACH MAKE AN INNER LINK ROLLER AMERICAN BRITISH Lubrication (Dependent on power
More informationThermx PCT. High-performance Polyester. Product and Properties Guide
Thermx PCT High-performance Polyester Product and Properties Guide Thermx Chemical resistance Processability Dimensional stability Heat resistance Fast molding cycles Thermx PCT polyester is a hightemperature
More informationWL115 WL Plastics PE4710 Water Pipe
WL115 WL Plastics PE4710 Water Pipe WL Plastics PE4710 Pressure Water Pipe WL Plastics WL Plastics is dedicated to the principle that customers should have the best in quality and service. WL Plastics
More information3M TM Dyneon TM Fluoroplastics. Product Comparison Guide.
3M TM Dyneon TM Fluoroplastics Product Comparison Guide. Characteristics 3M Dyneon Fluoroplastics. Nominal values, not for specification purposes 1) Melt Index is measured at the following conditions 265
More informationMITRAS MATERIALS GMBH
MITRAS MATERIALS GMBH Friedrich-Ochs-Str. 2 92637 Weiden/Opf. Tel.: 0961 / 89-810 / 89-812 Fax: 0961 / 89-672 Directory of services L a b o r a t o r y MITRAS MATERIALS GMBH Edition 02/18 Rev. 08 page
More informationA-700. Technical Information. Fluoroelastomers
A-700 Technical Information Introduction Viton A-700* is an A-family gum polymer that has demonstrated easy processing. This gum provides: Good flow for compression molding Good mold release Less mold
More informationCABELEC Conductive Compounds Product Selection Guide
Conductive Compounds CABELEC Conductive Compounds Product Selection Guide CABELEC Conductive Compounds Product SELECTION Guide Cabot s Performance Materials: Over 130 Years of Getting You Where You Want
More informationPremier Materials Technology, Inc.
Premier Materials Technology, Inc. How to get the BEST Dock Foundation Delivering quality marine solutions since 1992 7401 Central Avenue NE, Minneapolis, MN 55432 800-262-2275 www.premiermaterials.com
More informationPolyamide 6 & 66 for Injection Moulding
Polyamide 6 & 66 for Injection Moulding Promyde is a trademark of NUREL 1 NUREL Engineering Polymers Polymerization Integrated into In-House Compounding 50 years experience in polymerization processes
More informationPolyamide 6 for Injection Moulding
Polyamide 6 for Injection Moulding Promyde is a trademark of NUREL 1 NUREL Engineering Polymers Excellence in Polymerization Recent technical advancements in NUREL polymerization processes have enabled
More informationQUALITY FITS. Product range injection molding grades with reference data
QUALITY FITS. Product range injection molding grades with reference data POCAN COLOR NOMENCLATURE Pocan is available in a large number of colors. We use a six-digit number to precisely characterize the
More informationCONDUCTIVE COMPOUNDS. CABELEC Conductive Compounds Product Selection Guide
CONDUCTIVE COMPOUNDS CABELEC Conductive Compounds Product Selection Guide Cabot s Performance Materials: Over 130 Years of Getting You Where You Want to Go Cabot Corporation is a global performance materials
More informationHigh Surface Area Silica. High Performance Tread. STRUKTOL SCA 98 (Tetrasulfide)
Producers of Specialty Chemicals Struktol Company of America 1 E. Steels Corners Road P. O. Box 19 Stow, Ohio 9 www.struktol.com High Surface Area Silica in High Performance Tread with Next Generation
More information+GF+ CLASS 267. Factory Mutual Approved. HDPE Pipe & Pipe Fittings GEORG FISCHER PIPING SYSTEMS centralplastics.
Factory Mutual Approved CLASS 26 HDPE Pipe & Pipe Fittings CENTRAL PLASTICS 8.499.692 Table Of Contents 18-1 Design-Flow HDPE IPS HDPE Pipe (Iron Pipe ) 4-24 18-2 PE 368 HDPE Physical Properties - FM 18-3
More informationBLUE ULTRA Pipe & Tubing contains no regrind resin in its manufacture
BLUE ULTRA is extruded using current state of the art 100% pure PE4710 virgin resin with decades of successful history - no extra wall thickness is required to retain its extreme level of UV protection
More informationHigher Temperature PP-Based Composite Provides Nylon/PA- Level Performance at Lower Weight and Economic Feasibility
Higher Temperature PP-Based Composite Provides Nylon/PA- Level Performance at Lower Weight and Economic Feasibility Society of Plastic Engineers Automotive Composites Conference & Exhibition September
More informationHigh Performance ABS Products for Automotive Applications
High Performance ABS Products for Automotive Applications ELIX Polymers is a leading manufacturer of ABS (Acrylonitrile-Butadiene-Styrene) resins and derivatives in Europe. Operating from its head office
More informationCONDUCTIVE COMPOUND AND CONCENTRATES CABELEC CONDUCTIVE COMPOUNDS AND CONCENTRATES PRODUCT SELECTION GUIDE
CONDUCTIVE COMPOUND AND CONCENTRATES CABELEC CONDUCTIVE COMPOUNDS AND CONCENTRATES PRODUCT SELECTION GUIDE Performance and leadership in black plastics Cabot Corporation is a global performance materials
More informationPOlyNIl Product Brochure
POLYNIL Product Brochure APPLICATION PA6.6 Unreinforced for PRODUCT P50 FI P50 FIHS P50 FIBK P50 N P50 FL P50 FLBK P50 L Polynil P50 LBK PROPERTIES Internally Internally heat stabilized, Internally Nucleated,
More informationTKD SERIES 3-WAY BALL VALVES - TRUE UNION
TKD SERIES 3-WAY BALL VALVES - TRUE UNION The TKD offers a host of advanced features that set it apart from other multi-port valves. The patented seat stop carrier allows for in-line micro-adjustment of
More informationPOLYCAST CELL CAST ACRYLIC Solutions for Aerospace
POLYCAST CELL CAST ACRYLIC Solutions for Aerospace Delivering aircraft transparencies for the demanding aerospace industry. cast cell cast acrylic has been manufactured and trusted by the aerospace industry
More informationPhysical Properties. Temperature Limits. Durometer 60 +/-5. Average Elongation 350% Specific Gravity 1.50 Polymer Content 20% -20 o F to +212 o F
The Advance Standard Model AW Wraparound casing end seal is manufactured of 1/8 thick neoprene rubber, assuring excellent chemical resistance and resiliency. Also included are ½ wide T304 stainless steel
More informationElastomer Selection for Bio-Fuel Requires a Systems Approach
Elastomer Selection for Bio-Fuel Requires a Systems Approach From an Article in Sealing Technology by Gordon Micallef, Trelleborg Sealing Solutions, Malta and Axel Weimann, Trelleborg Sealing Solutions,
More informationQualityWatch. Report Number 1 CAPA. November A Periodic Report on Non CAPA Certified Aftermarket Replacement Parts
CAPA QualityWatch A Periodic Report on Non CAPA Certified Aftermarket Replacement Parts Report Number 1 November 2011 1 Certified Automotive Parts Association 1000 Vermont Avenue NW Suite 1010 Washington,
More informationVERLON No Swell Wear Rings
VERLON No Swell Wear Rings Ultra precision +.001 tolerance on cross section NO SWELL - Lowest friction Strength to 40,000 PSI Large range of widths, cross sections and diameters - metric too Features &
More informationGBL-600S. Technical Information. Fluoroelastomers
GBL-600S Technical Information Introduction Viton GBL-600S is a next generation, easy processing, peroxide-cured 68% fluorine fluoroelastomer based on new Advanced Polymer Architecture (APA) technology.
More informationSR GreenPoxy 33 / SZ 8525 Clear epoxy system for compression moulding
Page 1 / 8 SR GreenPoxy 33 / SZ 8525 Clear epoxy system for compression moulding High bio-based carbon content SR GreenPoxy 33 resin is outcoming from the latest innovations in bio-based chemistry. SR
More informationEFFECT OF TYRE OVERLOAD AND INFLATION PRESSURE ON ROLLING LOSS & FUEL CONSUMPTION OF AUTOMOBILES CARS
EFFECT OF TYRE OVERLOAD AND INFLATION PRESSURE ON ROLLING LOSS & FUEL CONSUMPTION OF AUTOMOBILES CARS D.MADHUSUDHANA 1 C. NAGARAJA 2 PG Student Assistant Professor Dept. of Mechanical Engineering Dept.
More informationTKD SERIES 3-WAY BALL VALVES - TRUE UNION
TKD SERIES 3-WAY BALL VALVES - TRUE UNION The TKD offers a host of advanced features that set it apart from other multi-port valves. The patented seat stop carrier allows for in-line micro-adjustment of
More informationPLUG ASSIST MATERIALS FOR IMPROVED FORMING OF TRANSPARENT POLYPROPYLENE
PLUG ASSIST MATERIALS FOR IMPROVED FORMING OF TRANSPARENT POLYPROPYLENE By Kathleen Boivin and Noel Tessier CMT s Inc., Attleboro, MA Introduction A new class of syntactic foam with a copolymer base, available
More informationSR InfuGreen 810 Green Epoxy systems for Injection and Infusion
Page 1 / 9 SR InfuGreen 810 Green Epoxy systems for Injection and Infusion The InfuGreen 810 is a two-component epoxy system. It has been specially formulated for resin transfer processes, such as injection
More informationSolvay/ Torlon Thrust Bearing Discussion Torlon Versus Vespel Brian Stern
Solvay/ Torlon Thrust Bearing Discussion Torlon Versus Vespel 8-7-2018 Brian Stern Agenda Torlon Commercial Applications Thrust Bearing Requirements Torlon Property Discussion Torlon Friction and Wear
More informationCASE STUDY: TOUGH LOW MASS CLASS A SMC
CASE STUDY: TOUGH LOW MASS CLASS A SMC Edward Zenk Navistar, Inc. David Hearn Core Molding Technologies Kevin Dinan, Robert Seats, & Cedric Ball Ashland Inc. Abstract Fuel is one of the single largest
More informationT.I. Midwood Co Ltd Green Lane Wardle Nantwich Cheshire CW5 6BJ T: +44 (0) F: +44 (0)
Features and Benefits Version 05/07/2014 High bond strength with High load resistance Used with all grades of threaded rod and rebar in accordance with TR029 Used in non-cracked and cracked concrete Fast
More informationPVC SCHEDULE 40 FITTINGS
PVC SCHEDULE 40 FITTINGS Performance Engineered & Tested 40-2-0604 SPEARS Schedule 40 PVC fitting designs combine years of proven experience with computer generated stress analysis to yield the optimum
More informationCONTROL PARAMETERS AND MATERIAL SELECTION CRITERIA FOR RAPID PROTOTYPINGSYSTEMS. James W. ComblWilliam R. Priedeman Stratasys, Inc.
CONTROL PARAMETERS AND MATERIAL SELECTION CRITERIA FOR RAPID PROTOTYPINGSYSTEMS James W. ComblWilliam R. Priedeman Stratasys, Inc. Abstract Since the introduction ofrapid prototyping technology as a tool
More informationWolf Kunststoff ZEDEX ZX-530 A5D Polymer Alloy
Wolf Kunststoff ZEDEX ZX-530 A5D Polymer Alloy Category : Polymer, Thermoplastic Material Notes: Main Characteristics: Low Creep; Low moisture absorption; Flame retardant; Low impurity ions; Good machinability;
More informationMANUFACTURING QUALITY CONTROL GEOMEMBRANES AND DRAINAGE PRODUCTS
MANUFACTURING QUALITY CONTROL GEOMEMBRANES AND DRAINAGE PRODUCTS AGRU AMERICA, INC. 500 Garrison Road Georgetown, SC 29440 Toll Free: (800) 373-2478 Telephone: (843) 546-0600 Fax: (843) 527-2738 salesmkg@agruamerica.com
More informationEpoxy Resin L Unit Value
Technical data Epoxy Resin L + Hardener S, L, CL, EPH 500, W 300, GL 1, GL 2, EPH 573 and EPH 161 Low viscosity, free of solvents and fillers Fast impregnation of glass, aramid, and carbon fibres High
More informationPerformance Testing of Composite Bearing Materials for Large Hydraulic Cylinders
TECHNICAL Performance Testing of Composite Bearing Materials for Large Hydraulic Cylinders Leo Dupuis, Bosch-Rexroth Sr. Development Engineer Introduction Large hydraulic cylinders (LHCs) are integral
More informationImplementation and Thickness Optimization of Perpetual Pavements in Ohio
Implementation and Thickness Optimization of Perpetual Pavements in Ohio OTEC 2015 Issam Khoury, PhD, PE Russ College of Engineering and Technology Ohio University, Athens, Ohio Outline Background prior
More informationNORDEL EPDM Product Selection Guide
NORDEL EPDM Product Selection Guide NORDEL EPDM products are members of Dow s family of ethylene propylene diene terpolymers and feature the widest range of ethylene content available in the industry.
More informationQCB Thermoplastic Bearing Units
QCB Thermoplastic Bearing Units CAT TP 2017 E Ver1 NBC Group Ltd In the interest of continuing improvement, NBC Group Ltd reserves the right to modify any product or specification without prior notice.
More informationHeat Seal Characteristics of Cyclic Olefin Copolymer / Polyethylene Blends. Topas Advanced Polymers A member of Daicel/Polyplastics Group
Heat Seal Characteristics of Cyclic Olefin Copolymer / Polyethylene Blends 1 Introduction Cyclic Olefin Copolymers (COC) use is growing in flexible packaging films Attributes include easy processing, stiffness,
More informationimpulse Single-Use Mixers
DATA SHEET impulse Single-Use Mixer (S.U.M.) impulse Single-Use Mixers Standard specifications Introduction The Thermo Scientific impulse Single-Use Mixer (S.U.M.) is designed for liquid-to-powder, liquid-to-liquid,
More informationSHINKONG SHINITE PBT. For Loose Tube
SHINKONG SHINITE PBT For Loose Tube 新光合成纖維股份有限公司 Shinkong Synthetic Fibers Corporation 台北市南京東路二段 123 號 8 樓 8th FL., 123, Sec. 2. Nanking E. Rd. Taipei, Taiwan TEL : 886 2 2507 1251 FAX: 886 2 2506 8047
More informationProduct Guide Complete Product And Packaging Specifications Inside
Product Guide OPTIX Acrylic Sheet DURAPLEX Impact Modified Acrylic Sheet VIVAK PETG Sheet ABS Sheet Roll Stock Sign Grade Acrylic Sheet OPTIX LD Light Diffusing Sheet Colored Acrylic Sheet Patterned Acrylic
More informationChallenges For Future Powerplant Coolant Systems
Challenges For Future Powerplant Coolant Systems Steven Mok, Karla Butler, Terrence Cressy, Paul Kane, Brian Fish (Presented at SPE Auto EPCON, April 28, 2009. Sterling Heights, MI) 2 Discussion Agenda
More informationPolyfixer PSF. Features and Benefits Version: 14/04/2015
Features and Benefits Version: 14/04/2015 Good bond strength with High load resistance Used with all grades of threaded rod Used in concrete and masonry Fast gelling and curing Used in dry and wet conditions
More informationinnerduct Innerduct INNERDUCT tidbit
innerduct Innerduct Innerduct is manufactured from High Density Polyethylene in accordance with the specifications of ASTM F-2160 and/or NEMA TC 7. Other dimensional requirements may be acceptable upon
More informationWeldalloy Catalogue 1
Weldalloy Catalogue 1 ONTE Contents P Pig s Tail Protective Wrapping........ 3 Pig s Tail Data Sheet.............. 4 Fire Resistant Anti Static Pig s Tail..... 6 Electrical Guard................... 7 Tidy
More informationWeldalloy Catalogue 1
Weldalloy Catalogue 1 ONTE Contents p Pig s Tail Protective Wrapping........ 3 Pig s Tail Data Sheet.............. 4 Fire Resistant Anti Static Pig s Tail..... 6 Electrical Guard................... 7 Tidy
More informationThe joint product portfolio of MOL Petrochemicals and Slovnaft provides infinite opportunities
DESCRIPTION TIPELIN 2100J is a high density unimodal polyethylene copolymer (with propene-1 as comonomer) intended for injection moulding of general purpose products. It offers good balance of properties
More informationMIL-STD-883G METHOD LEAD INTEGRITY
LEAD INTEGRITY 1. PURPOSE. This method provides various tests for determining the integrity of microelectronic device leads (terminals), welds, and seals. Test condition A provides for straight tensile
More informationDetection of Sulfur Compounds in Natural Gas According to ASTM D5504 with an Agilent Dual Plasma Sulfur Chemiluminescence Detector
Detection of Sulfur Compounds in Natural Gas According to ASTM D554 with an Agilent Dual Plasma Sulfur Chemiluminescence Detector Application Note Author Rebecca Veeneman Abstract Sulfur compounds in natural
More informationECCENTRIC PLUG VALVES
Serving the Water & Waste Water Industry Since 1878 ECCENTRIC PLUG VALVES C517 3 24 sizes available Multiple end connections available M&H Valve is a division of McWane, Inc. www.mh-valve.com AVAILABLE
More informationimpulse Single-Use Mixers
impulse Single-Use Mixers Standard specifications COL02488 Introduction The Thermo Scientific impulse Single-Use Mixer (S.U.M.) is designed for liquid-to-powder, liquid-to-liquid, and suspension mixing.
More informationDETAIL SPECIFICATION SHEET INSULATION SLEEVING, ELECTRICAL, HEAT SHRINKABLE, POLYOLEFIN, FLEXIBLE, CROSSLINKED
INCH-POUND MIL-DTL-23053/5C 17 June 1996 SUPERSEDING MIL-I-23053/5B 01 May 1986 DETAIL SPECIFICATION SHEET INSULATION SLEEVING, ELECTRICAL, HEAT SHRINKABLE, POLYOLEFIN, FLEXIBLE, CROSSLINKED This specification
More informationDETAIL SPECIFICATION SHEET
INCHPOUND MILDTL85052/1C 30 March 2005 SUPERSEDING MILC85052/1B 30 MAY 1984 DETAIL SPECIFICATION SHEET CLAMP, LOOP, TUBE177 PH CRES, 275 o F, FUEL AND PETROLEUM BASED HYDRAULIC FLUID RESISTANT This specification
More informationImproved Adhesion EVA for Extrusion Coating / Extrusion Laminating. Presented by: Scott Weber AD&TS Engineer Celanese
Improved Adhesion EVA for Extrusion Coating / Extrusion Laminating Presented by: Scott Weber AD&TS Engineer Celanese Overview Objective Market / Applications Experimental Procedures Results Conclusions
More informationTechnical Data Sheet SUPER SAP CLR Epoxy System Clear, General Purpose Liquid Epoxy Resin
Technical Data Sheet SUPER SAP CLR Epoxy System Clear, General Purpose Liquid Epoxy Resin Product Overview SUPER SAP CLR SYSTEM is composed of Super Sap CLR Epoxy, a modified, clear liquid epoxy resin,
More informationSMC/Fiberglass Repair Adhesive - 90
SMC/Fiberglass Repair Adhesive - 90 Technical Data Sheet June, 2014 3M Part No.(s) 3M Part Descriptor(s) 3M SMC/Fiberglass Repair Adhesive - 90 Product Description 3M SMC/Fiberglass Repair Adhesive - 90,
More informationPaint Resin in Thermoplastics Properties and Applications
Paint Resin in Thermoplastics Properties and Applications Jennifer Lynch EPA Seminar Technology Review and Demonstration of Paint Resin Reclamation Technology for Use in Thermoplastics June 12, 2008 Overview
More informationAKROMID FR (PA 6.6, PA 6, PA 6.6/PA 6, PPA) AKROLOY FR (PA Blend)
FLAME-RETARDANT COMPOUNDS AKROMID FR (PA 6.6, PA 6, PA 6.6/PA 6, PPA) AKROLOY FR (PA Blend) AKRO-PLASTIC GmbH Member of the Feddersen Group Flame-retardant Products Increasingly Important for Extended
More informationSTATISTICAL ANALYSIS OF STRUCTURAL PLATE MECHANICAL PROPERTIES
STATISTICAL ANALYSIS OF STRUCTURAL PLATE MECHANICAL PROPERTIES FINAL REPORT Prepared for American Iron and Steel Institute Somchat Suwan Lance Manuel Karl H. Frank Department of Civil Engineering The University
More informationDevelopment of High-performance Phenolic Resin Idler Pulley
TECHNICAL PAPER Development of High-performance Phenolic Resin Idler Pulley H. ARAI K. MORI Resins idler pulleys in automotive engines are increasingly used for improving fuel efficiency through weight
More informationSuch as scratching, scoring, excessive packing wear, stuffing box damage... Have you ever wondered if there was any way to guide a polished rod?
Have you heard of or had problems with polished rod damage? Such as scratching, scoring, excessive packing wear, stuffing box damage... Have you ever wondered if there was any way to guide a polished rod?
More informationFilabot Original and Filabot EX2. Operation Manual
Triex LLC Barre, Vermont 05641 USA 1 802 505 6772 Filabot Original and Filabot EX2 Operation Manual This manual applies to the Filabot Original and Filabot EX2 by Triex LLC. Triex LLC, Barre, VT 05641,
More informationBS-40 BS-25 BS-27* BS-07* BS-10* BS-12* BS-22* BS-02* BS-15 BS-08 BS-39
COLOR OPTIONS Please Call For Availability SPECIALTY WHITE BLACK BROWN GREY CLEAR BS-02 BS-02-SD FEEL THE DIFFERENCE Of Our Soft Durometer Line *SD = Optional Soft Durometer Domestic Phone: 856-345-7650
More informationDRISCOPIPE 8100 HDPE PIPE and FITTINGS DATA SHEET
PerfmancePipe.com DRISCOPIPE 8100 HDPE PIPE and FITTINGS DATA SHEET Driscopipe 8100 Pipe and Fittings meet exceed: Driscopipe 8100 Pipe and Fittings f: ASTM D2513, D2683, D3261 ASTM D3350, cell classification
More informationPolyJet 3D Printers Systems and Materials Overview
1 Broad Versatility with Extraordinary Realism PolyJet 3D Printers empower professional designers, engineers, educators and healthcare professionals to create and problem-solve with precision, speed and
More information201 E. Steels Corners Road P. O. Box 1649 Stow, Ohio Producers of Specialty Chemicals DYNAMAR REPLACEMENT
Struktol Company of America 201 E. Steels Corners Road P. O. Box 1649 Stow, Ohio 44224-0649 Producers of Specialty Chemicals DYNAMAR REPLACEMENT STRUKTOL WS 280 and OTHERS Prepared by Joseph J. Wasko,
More informationResearch Progress in Calenderable Fluorosilicone with Excellent Fuel Resistance
Research Progress in Calenderable Fluorosilicone with Excellent Fuel Resistance Haibing Zhang, Ph.D. Andy Cloud Arlon licone Technologies Division 1100 Governor Lea Road Bear, DE 19701 302-834-2100 Abstract
More informationStandard Classification System for Carbon Blacks Used in Rubber Products 1
Designation: D 1765 04 Standard Classification System for Carbon Blacks Used in Rubber Products 1 This standard is issued under the fixed designation D 1765; the number immediately following the designation
More informationAndreas DOWE*, Dr. Christian BARON*, Reinhardt BÜSSING**
X Międzynarodowa Konferencja Techniczna: 2-21 września, 27, Płock Zarządzanie Ryzykiem w Eksploatacji Rurociągów New VESTAMID (Polyamide 12) grades to manufacture products with large geometrical dimensions
More informationB-202. Technical Information. Fluoroelastomers
B-202 Technical Information Introduction Viton B-202* fluoroelastomer is a low viscosity, B-type gum polymer that demonstrates improved processing and rheology when compared with existing fluoroelastomers.
More informationPE-HDXc pipes (physically cross-linked polyethylene pipes)
pipes (physically cross-linked polyethylene pipes) Applications: Domestic drinking water installations, radiator connections and surface regulation Special properties high chemical resistance (according
More informationWear Rings / Bearings
Wear Rings / Bearings Contents Product Offering... -3 Engineering... -4 Materials... -6 Wear Rings / Bearings Profiles WPT... -8 WRT... -12 PT... -16 PW... -20 Wear Rings / Bearings Parker offers a complete
More informationTable of CONTENTS AB AB AB-138 (FDA) AB BLAST AB
7069-F (03-05-2018) Table of CONTENTS SECTION 1 : NATURAL (NR)...1. AB-131...1.1 AB-135...1.2 AB-138 (FDA)...1.3 AB-139 - BLAST...1.4 AB-148...1.5 SECTION 2 : SBR (Packing and Skirtboard)...2. IM-165...2.1
More informationKEPITAL LOF Grade. (Low Emission POM for Automotive Interiors) R&D Center
KEPITAL LOF Grade (Low Emission POM for Automotive Interiors) R&D Center Contents 1. Global VOC Standards Impact U.S. Tier Suppliers - 3 page 2. KEPITAL LOF POM Characteristics and Benefits - 3 page 3.
More informationGeomembrane Test Methods
Appendix 2 Geomembrane Test Methods AMERICAN SOCIETY FOR TESTING AND MATERIALS (arranged by number) ASTM D-5 ASTM D-36 ASTM D-256 ASTM D-412 ASTM D-413 ASTM D-471 ASTM D-570 ASTM D-638 ASTM D-696 ASTM
More informationNeopolen P 9230 ESD. Bulk density 1) Average Average Color 2) particle size particle weight [ kg/m 3 ] [ mm ] [ mg ]
= registered trademark of BASF SE Neopolen P 9230 ESD Product Description Neopolen P 9230 ESD is expanded Polypropylene supplied in the form of beads. The cells are largely closed. Table 1: Bulk density
More informationCOMPUTATIONAL FLOW MODEL OF WESTFALL'S 2900 MIXER TO BE USED BY CNRL FOR BITUMEN VISCOSITY CONTROL Report R0. By Kimbal A.
COMPUTATIONAL FLOW MODEL OF WESTFALL'S 2900 MIXER TO BE USED BY CNRL FOR BITUMEN VISCOSITY CONTROL Report 412509-1R0 By Kimbal A. Hall, PE Submitted to: WESTFALL MANUFACTURING COMPANY May 2012 ALDEN RESEARCH
More informationTHE EFFECTS OF RUNNING DIFFERENT BARREL TEMPERATURE PROFILES FOR VARIOUS RESINS
THE EFFECTS OF RUNNING DIFFERENT BARREL TEMPERATURE PROFILES FOR VARIOUS RESINS Walter S. Smith Luke A. Miller Jason Willis Timothy W. Womer Xaloy Corporation, New Castle, PA Abstract Differences in solids
More information