GATE, GLOBE & CHECK VALVES - CAST STEEL SHORT VERSION

Transcription

1 GTE, GLOBE & CHECK VLVES - CST STEEL SHORT VERSION

2 QULITY VLVE MNUFCTURER

3 USTRLIN PIPELINE VLVE Contents Figure Number System Material Combinations/Features PI 600 Trim Types Physical & Chemical Properties General Design Specifications Valve Selection Criteria Bolted Bonnet Gate Valves Overview Bolted Bonnet Globe Valves Overview Bolted Bonnet Check Valves Overview Pressure Seal Bonnet Valves Overview Gate Valve - Class 150 Gate Valve - Class 300 Gate Valve - Class 600 Gate Valve - Class 900 Gate Valve - Class 1500 Gate Valve (PSB) - Class 900 Gate Valve (PSB) - Class 1500 Globe Valve - Class 150 Globe Valve - Class 300 Globe Valve - Class 600 Globe Valve - Class 900 Globe Valve - Class 1500 Globe Valve (PSB) - Class 900 Globe Valve (PSB) - Class 1500 Swing Check Valve - Class 150 Swing Check Valve - Class 300 Swing Check Valve - Class 600 Swing Check Valve - Class 900 Swing Check Valve - Class 1500 Swing Check Valve (PSB) - Class 900 Swing Check Valve (PSB) - Class 1500 Stainless Steel Gate Valve - Class 150 Stainless Steel Gate Valve - Gate 300 Stainless Steel Globe Valve - Class 150/300 Stainless Steel Check Valve - Class 150/300 By-Pass & Drains Steamco Parallel Slide - Class Steamco Stop Check - Class Steamco Y Pattern Stop Check Globe - Class Steamco Right ngle Globe - Class Steamco Non Return Lift - Class Flowturn Check Cast Iron - Class 125/250 Flowturn Gate Cast Iron - Class 125/250 Flowturn Globe Cast Iron - Class 125/250 Technical Data - Equalising Devices Technical Data - By-Passes Technical Data - Drain & Bleed Connections Technical Data - Flow Formulation Technical Data - Flow Coefficients ctuation Torque & Top Works Specifications Technical Considerations USTRLIN PIPELINE VLVE Stanbel Road Salisbury Plain South ustralia 5109 Telephone +61 (0) Fax +61 (0) admin@australianpipelinevalve.com.au Page 4-5 Page 6-8 Page 9 Page 10* Page 11 Page 12-13* Page 14 Page 15 Page 16 Page Page 21 Page 22 Page 23 Page 24 Page 25 Page 26 Page 27 Page 28 Page 29 Page 30 Page 31 Page 32 Page 33 Page 34 Page 35 Page 36 Page 37 Page 38 Page 39 Page 40 Page 41 Page 42* Page 43* Page 44* Page 45* Page 46* Page 47-50* Page 51* Page 52* Page 53* Page 54* Page 55* Page 56-57* Page 58* Page 59* Page 60* Page 61* Page 62* Page 63-67* Page 68-69* Page 70 * This version excludes these pages, refer to website for full version.

4 USTRLIN PIPELINE VLVE Consistent product quality and a proven track record makes ustralian Pipeline Valve a dependable choice for cast Gate, Globe and Check Valves, where total reliability is the number one concern. Figure Number System EXMPLE 150 P145Q* 1 H T N 9 P BW160 G - T Bonnet gasket: Blank Standard:- SS Spiral + GRP (BB), Pressure Seal Ring (PSB). N/:- (WB) SS Spiral + PTFE B S31803 Spiral C PTFE D SS Spiral + PTFE + GRP E Ring Z Special Stem packing: Blank Standard:- Graphite. N/:- (Check Valves) L Graphite + PTFE T PTFE F Fugitive Emission GRP I Fugitive Emission PTFE J Special Operator: Blank Handwheel or N/ ctuator G Gear H Hammer Blow Handwheel End connection: Blank RF (B16.5) B RF B16.47 (MSS SP44) BB RF B16.47B (PI605) RJ RTJ BW (+Schedule) Buttweld FF Flat Face SP is special drilling UD Undrilled UM Unmachined for RF/RJ Bonnet: Blank Bolted C Cryogenic L Low Temperature P Pressure Seal W Welded Body material: - see page 5. (WCB is Blank) Blank Non NCE N NCE Blank Standard Configuration* 2 D Globe-Stop Check F Flexible Disc Gate P Full Opening Check (PI6D) Q Tilt Check R Right ngle S Parallel Slide T S Bend Globe Y Inclined Bonnet Z c/w Spring * 2 Example Solid Wedge Denotes trim (see below) Basic model number denoting valve class and valve type (s shown in catalogue) * 1 For Gate Valves -Q denotes PI603 Blank PI600 Valve Size (mm) Trim Types PGE 4 TRIM CODE BODY SET SURFCE DISC SURFCE STEM B Bronze Bronze Bronze Bronze C L-Bronze L-Bronze L-Bronze L-Bronze D* Monel* Monel* Monel Monel E* F51* F51* F51 F51 G* F55* F55* F55 F55 H* Hastelloy B* Hastelloy B* Hastelloy B Hastelloy B L* F316* F316* F316 F316 N* lloy 20* lloy 20* lloy 20 lloy 20 P* F304* F304* F304 F304 Q* lloy 625* lloy 625* lloy 625 lloy 625 U Stellite Stellite F6/410 F6/410 W* F347* F347* F347 F347 X F6/410 F6/410 F6/410 F6/410 XU Stellite F6/410 F6/410 F6/410 Y* Special* Special* Special Special BCK SET (STUFFING BOX) * Note if stellite seat then add XU modifier to end, if stellite seat and disc then add U modifier, if PTFE seat add T modifier.

5 Figure Number Codes BODY MTERIL CODE BODY/BONNET ND OR CP MTERILS Suffix STM Spec. Material None 216 Gr. WCB Carbon Steel WCC Carbon Steel WC1 Carbon Moly 1/2% Mo LCC Low Carbon Steel 2B 352 LCB Low Carbon Steel CF3M Stainless with Molybdenum (low carbon) Gr. C5 5% Cr, 1/2% Mo Gr. WC6 1-1/4% Cr, 1/2% Mo Gr. WC9 2-1/4% CR, 1% Mo CF8 Stainless 18% Cr, 8% Ni 8D 351 CF8C Stainless 18% Cr, 10% Ni & Cb 8M 351 CF8M Stainless with Molybdenum Gr. C12 Chrome Moly 9% Cr, 1% Mo LC1 Carbon Moly 1/2% Mo LC3 Low Carbon Steel CN7M lloy /351-CD3MN Duplex (F51) CD3MWCuN/6 Super Duplex (F55) 19 Bronze Bronze B62/LG2/B L-Bronze luminium Bronze 0 SPECIL -Q PI603 wall PGE 5

6 Material Combinations/Features CST STEEL GTE VLVES NSI CLSS 150 ~ 2500 FETURES Bolted bonnet, OS&Y, Flexible wedge. On smaller size valves, the yoke is cast integral with bonnet. Larger size valves have two piece yoke, refer to individual drawing. Stem nut is mounted with ball bearings to reduce operating torque for ease of manual operation in larger sizes and higher classes. Self aligning two piece gland PPLICBLE STNDRDS Valves designed to PI Std. 600 and BS 1414 Valves tested to PI Std. 598 Face-to-face to NSI B16.10 Flanged ends to NSI B16.5 Butt-welding ends to NSI B16.25 Trim and seating surface as per PI 600 standard. MTERIL LIST Carbon Steel lloy Steel Stainless Steel Part Name No. WCB WCC LCB LCC C5 WC6 WC9 CF8 CF8M CF3 CF3M PV Suffix Code 1 2B M 0 3M 1 Body 216 WCB 216 WCC 352 LCB 352 LCC 217 C5 217 WC6 217 WC9 351 CF8 351 CF8M 351 CF3 351 CF3M 2 Seat Ring LF2 350 LF2 182 F F F F F F304L 182 F316L 3 Wedge 216 WCB 216 WCC 352 LCB 217 CF8 217 C5 217 WC6 217 WC9 351 CF8 351 CF8M 351 CF3 351 CF3M 4 Stem 182 F6 182 F6 182 F F F F F F F F304L 182 F316L 5 Bonnet Bolt 193 B7 320 L7 193 B B8 193 B8M 6 Bonnet Nut 194 2H Gasket Solid metal serrated gasket Stainless Steel & Graphite wound Non-metallic gasket Stainless Steel or Soft Iron Ring Gasket 8 Bonnet 216 WCB 216 WCC 352 LCB 352 LCC 217 C5 217 WC6 217 WC9 217 CF8 351 CF8M 351 CF3 351 CF3M 9 Back Seat Bushing 182 F6 182 F6 182 F6 182 F6 182 F F F F F F304L 182 F316L 10 Stem Packing Braided/Flexible Graphite or PTFE 11 Lantern* F6 182 F6 182 F6 182 F6 182 F F F F F L 182 F316L 12 Pin Carbon Steel Stainless Steel lloy Steel 13 Gland 182 F6 182 F6 182 F6 182 F6 182 F F F F F F304L 182 F316L 14 Gland Flange 216 WCB 216 WCC 352 LCB 352 LCC 217 C5 217 WC6 217 WC9 351 CF8 351 CF8M 351 CF3 351 CF3M 15 Gland Eyebolt 307 B 307 L7 193 B7 193 B8 193 B8M 16 Gland Nut 194 2H Stem Nut 439D2 (ustenitic DI) ZCu110Fe3 (L-Bronze) 18 Retaining Nut Carbon Steel or lloy Steel 19 Hand Wheel Ductile Iron or Carbon Steel 20 H.W. Lock Nut Carbon Steel Stainless Steel lloy Steel 21 Yoke 216 WCB 216 WCC 352 LCB 352 LCC 217 C5 217 WC6 217 WC9 351 CF8 351 CF8M 351 CF3 351 CF3M 22 Nipple Copper lloy or Carbon Steel or Stainless Steel 23 Seat/Wedge Facing 13Cr or 16Cr-8Ni or HF(Co-Cr) or 316 or 304 *1 Lantern Ring where applicable PGE 6

7 Material Combinations/Features CST STEEL GLOBE VLVES NSI CLSS 150 ~ 2500 FETURES Bolted bonnet, OS&Y, Swivel Disc. Plug type disc (Ball type also available). On smaller sizes, the yoke is cast integral with bonnet. Larger sizes have two piece yoke, refer to individual drawing. Stem nut is mounted with ball bearings to reduce operating torque for ease of manual operation in larger sizes and higher classes. PPLICBLE STNDRDS Valves designed to PI Std. 600 and BS 1873 Valves tested to PI Std. 598 Face-to-face to NSI B16.10 Flanged ends to NSI B16.5 Butt-welding ends to NSI B16.25 MTERIL LIST Carbon Steel lloy Steel Stainless Steel Part Name No. WCB WCC LCB LCC C5 WC6 WC9 CF8 CF8M CF3 CF3M PV Suffix Code 1 2B M 0 3M 1 Body 216 WCB 216 WCC 352 LCB 352 LCC 217 C5 217 WC6 217 WC9 351 CF8 351 CF8M 351 CF3 351 CF3M 2 Seat Ring LF2 350 LF2 182 F F F F F F304L 182 F316L 3 Disc WCC 350 LF2 352 LCC 217 C5 217 WC6 217 WC9 351 CF8 351 CF8M 351 CF3 351 CF3M 4 Stem 182 F6 182 F6 182 F F F F F F F F304L 182 F316L 5 Disc Nut 182 F6 182 F6 182 F6 182 F F F F F F F304L 182 F316L 6 Gasket Solid metal serrated gasket Stainless Steel & Graphite spiral wound Non-metallic gasket Stainless Steel or Soft Iron Ring Gasket 7 Bonnet 216 WCB 216 WCC 352 LCB 352 LCC 217 C5 217 WC6 217 WC9 351 CF8 351 CF8M 351 CF3 351 CF3M 8 Bonnet Bolt 193 B7 320 L7 193 B B8 193 B8M 9 Bonnet Nut 194 2H Back Seat Bushing 182 F6 182 F6 182 F6 182 F6 182 F F F F F L 182 F316L 11 Stem Packing Braided/Flexible Graphite or PTFE 12 Lantern* 182 F6 182 F6 182 F6 182 F6 182 F F F F F F304L 182 F316L 13 Pin Carbon Steel Stainless Steel lloy Steel 14 Gland Flange 216 WCB 216 WCC 352 LCB 352 LCC 217 C5 217 WC6 217 WC9 351 CF8 351 CF8M 351 CF3 351 CF3M 15 Gland 182 F6 182 F6 182 F6 182 F6 182 F F F F F F304L 182 F316L 16 Gland Eyebolt 307 B 307 L7 193 B7 193 B8 193 B8M 17 Gland Nut 194 2H Stem Nut 439D2 (ustentic DI) ZCu110Fe3 (L-Bronze) 19 Handwheel Ductile Iron or Steel 20 H.W. Lock Nut Carbon Steel Stainless Steel lloy Steel 21 Seat/Disc Facing 13Cr or 16Cr-8Ni or HF(Co-Cr) ST#6 or 316 or 304 * Lantern Ring where applicable. PGE 7

8 Material Combinations/Features 13* CST STEEL CHECK VLVES NSI CLSS 150 ~ 2500 FETURES Bolted cover Swing disc PPLIC BLE STNDRDS Valves designed to PI Std D and BS 1868 Valves tested to PI Std. 598 Face-to-face to NSI B16.10 Flanged ends to NSI B16.5 Butt-welding ends to NSI B16.25 Trim and seating surface as per PI 600 standard. MTERIL LIST Carbon Steel lloy Steel Stainless Steel Part Name No. WCB WCC LCB LCC C5 WC6 WC9 CF8 CF8M CF3 CF3M PV Suffix Code 1 2B M 0 3M 1 Body 216 WCB 216 WCC 352 LCB 352 LCC 217 C5 217 WC6 217 WC9 351 CF8 351 CF8M 351 CF3 351 CF3M 2 Seat Ring LF2 350 LF2 182 F F F F F F304L 182 F316L 3 Disc 216 WCB 216 WCC 352 LCB 352 LCC 217 C5 217 WC6 217 WC9 351 CF8 351 CF8M 351 CF3 351 CF3M 4 Disc Nut 182 F6 182 F6 182 F6 182 F6 182 F F F F F F304L 182 F316L 5 Hinge 216 WCB 216 WCC 352 LCB 352 LCC 217 C5 217 WC6 217 WC9 351 CF8 351 CF8M 351 CF3 351 CF3M 6 Hinge Pin 182 F6 182 F6 182 F6 182 F6 182 F F F F F F304L 182 F316L 7 Gasket Solid metal serrated gasket Stainless Steel & Graphite spiral wound Non-metallic gasket Stainless Steel or CD Plated Soft Iron Ring Gasket 8 Cover 216 WCB 216 WCC 352 LCB 352 LCC 217 C5 217 WC6 217 WC9 351 CF8 351 CF8M 351 CF3 351 CF3M 9 Cover Bolt 193 B7 320 L7 193 B B8 193 B8M 10 Cover Nut 194 2H Washer Carbon Steel or lloy Steel or Stainless Steel 12 Seat/Disc Facing 13Cr or 16Cr-8Ni or HF(Co-Cr) ST#6 or 316 or Eye Bolt* 193 B7 320 L7 The material is according to STM standard. * Eye bolt supplied in larger sizes & higher classes. PGE 8

9 PI 600 Trim Types The following tables detail standard trim material available. Special trims are available on request. PI Trim Number Nominal Trim Trim Code Stem & other trim parts Disc/Wedge Seat Surface Trim Material Grade Service F6 410 (13Cr) ( HBN) F6 (13Cr) (200 HBN) 410 (13Cr) (250 HBN min) 13Cr-0.75Ni-1Mn For oil and oil vapors and general services with heat treated seats and wedges. General very low erosive or non-corrosive service between -100ºC and 320ºC. This stainless steel material lends itself readily to hardening by heat treatment and is excellent for contacting parts such as stems, gates, and discs. Steam, gas & general service to 370ºC. Oil & Oil vapor 480ºC (18Cr-8Ni) 304 (18Cr-8Ni) 19Cr-9.5Ni-2Mn-0.08C For moderate pressure in corrosive, low erosive service between -265ºC and 450ºC (25Cr-20Ni) 310 (25Cr-20Ni) 310 (25Cr-20Ni) 25Cr-20.5Ni-2Mn For moderate pressure in corrosive or non corrosive service between -265ºC and 450ºC Hard F6H 410 (13Cr) ( HBN) F6 (13Cr) ( HBN) F6 (13Cr) (275 HBN min) 13Cr-0.75Ni-1Mn Seats 275 BHN min. s trim 1 but for medium pressure and more corrosive service Full Hard faced F6HF 410 (13Cr) ( HBN) F6+St Gr6 (CoCr lloy) (350 HBN min) 410+St Gr6 (CoCr lloy) (350 HBN min) 13Cr-0.5Ni-1Mn/Co-Cr- High pressure slightly erosive and corrosive service between -265ºC and 650ºC and higher pressure. Premium trim service to 650ºC. Excellent for high pressure water and steam service. 5a 410-Full Hard faced F6HF 410 (13Cr) ( HBN) F6+Hardf. NiCr lloy (350 HBN min) 410+Hardf. NiCr lloy (350 HBN min) 13Cr-0.5Ni-1Mn/Co-Cr- s trim 5 where Co is not allowed and Ni-Cu F6HFS 410 (13Cr) ( HBN) Monel 400 (NiCu lloy) (250 HBN min) Monel 400 (NiCu lloy) (175 HBN min) 13Cr-0.5Ni-1Mn/Ni-Cu s trim 1 and more corrosive service Very Hard F6HF+ 410 (13Cr) ( HBN) F6 (13Cr) (250 HBN min) F6 (13Cr) (750 HB) 13Cr-0.5Ni-1M0/13Cr-0.5Ni-1Mo Seats 750 BHN min. s trim 1 but for higher pressure and more corrosive/erosive service Hard faced F6HFS 410 (13Cr) ( HBN) 410 (13Cr) (250 HBN min) 410+St Gr6 (CoCr lloy) (350 HBN min) 13Cr-0.75Ni-1Mn/1/2Co-Cr- Universal trim for general service requiring long service life up to 593ºC. s trim 5 for moderate pressure and more corrosive service. Steam, gas & general service to 540ºC. Standard trim for gate valves. 8a Hard faced F6HFS 410 (13Cr) ( HBN) F6 (13Cr) (250 HBN min) 410+Hardf. NiCr lloy (350 HBN min) 13Cr-0.75Ni-1Mn/1/2Co-Cr- s trim 5a for moderate pressure and more corrosive service 9 Monel Monel Monel (NiCu lloy) Monel 400 (NiCu lloy) Monel 400 (NiCu lloy) 70Ni-30Cu For corrosive service to 450ºC such as acids, alkalies, salt solutions, etc. Very corrosive fluids. Erosive-corrosive service between -240ºC and 480ºC. Resistant to sea water, acids, alkalies. Has excellent corrosion resistance in chlorine and alkylation service (18Cr-Ni-Mo) 316 (18Cr-Ni-Mo) 316 (18Cr-Ni-Mo) 18Cr-12Ni-2.5Mo-2Mn For superior resistance to corrosion for liquids and gases which are corrosive to 410 stainless steel up to 455ºC. s trim 2 but a higher level of corrosive service. Provides excellent resistance to corrosive media at high temperatures and toughness for service at low temperatures. Low temperature service standard for 316SS valves. 11 Monel - Hard faced MonelHFS Monel (NiCu lloy) Monel 400 (NiCu lloy) Monel 400+St Gr6 (350HBN min) 70Ni-30Cu/1/2Co-Cr- s trim 9 but for medium pressure and more corrosive service. 11a Monel - Hard faced MonelHFS Monel (NiCu lloy) Monel 400 (NiCu lloy) Monel 400+HF NiCr lloy (350 HBN min) 70Ni-30Cu/1/2Co-Cr- s trim 9 but for medium pressure and more corrosive service Hard faced 316HFS 316 (Cr-Ni-Mo) 316 (18Cr-8Ni-Mo) 316+St Gr6 (350 HBN min) 18Cr-12Ni-2.5Mo-2Mn1/2Co-Cr- s trim 10 but for medium pressure and more corrosive service. 12a Hard faced 316HFS 316 (Cr-Ni-Mo) 316 (18Cr-8Ni-Mo) 316 Hardf. NiCr lloy (350 HBN min) 18Cr-12Ni-2.5Mo-2Mn1/2Co-Cr- s trim 10 but for medium pressure and more corrosive service. 13 lloy 20 lloy 20 lloy 20 (19Cr-29Ni) lloy 20 (19Cr-29Ni) lloy 20 (19Cr-29Ni) 29Ni-19Cr-2.5Mo-0.07C Very corrosive service. For moderate pressure between -45ºC and 320ºC. 14 lloy 20 - Hard faced lloy 20HFS lloy 20 (19Cr-29Ni) lloy 20 (19Cr-29Ni) lloy 20 St Gr6 (350 HBN min) 29Ni-19Cr-2.5Mo-0.07C/1/2Co-Cr- s trim 13 but for medium pressure and more corrosive service. 14a lloy 20 - Hard faced lloy 20HFS lloy 20 (19Cr-29Ni) lloy 20 (19Cr-29Ni) lloy 20 Hardf. NiCr lloy (350 HBN min) 29Ni-19Cr-2.5Mo-0.07C/1/2Co-Cr- s trim 13 but for medium pressure and more corrosive service Full Hard faced 304-HF 304 (18Cr-8Ni-Mo) 304St Gr6 304+St Gr6 (350 HBN min) 19Cr-9.5Ni-2Mn-0.08C/1/2Co-Cr- s trim 2 but more erosive service & higher pressure Full Hard faced 316-HF 316 HF (18Cr-8Ni-Mo) 316+St Gr6 (320 HBN min) 316+St Gr6 (350 HBN min) 18Cr-12Ni-2.5Mo-2Mn/Co-Cr-Mo s trim 10 but more erosive service & higher pressure Full Hard faced 347-HF 347 HF (18Cr-10Ni-Cb) 347+St Gr6 (350 HBN min) 347+St Gr6 (350 HBN min) 18Cr-10Ni-Cb/Co-Cr- s trim 13 but more corrosive service & higher pressure. Combines good corrosion resistance with high temperature resistance up to 800ºC. 18 lloy 20 - Full Hard faced lloy 20 HF lloy 20 (19Cr-29Ni) lloy 20+St Gr6 (350 HBN min) lloy 20+St Gr6 (350 HBN min) 19Cr-29Ni/Co-Cr- s trim 13 but more corrosive service & higher pressure. Water, gas or low pressure steam to 230ºC. Special Bronze Bronze 410 (CR13) Bronze Bronze Water, oil, gas, or low pressure steam to 232ºC. Special lloy 625 lloy 625 lloy 625 lloy 625 lloy 625 NCE Specially treated 316 or 410 trim combined optionally with B7M bolts and 2HM nuts to meet NCE MR requirements. Full Stellite Full Hardfaced trim, suitable for abrasive & severe servicces up to 1200 F (650 C). Important Note: Data provided in this chart is for informational purposes only. lways consult current PI publications to verify information and trim data. ustralian Pipeline Valve (PV) recommends that customer s engineers analyse service requirements and specify the materials they consider optimum for their service conditions. Temperatures shown will vary depending on service applications, pressure and media type. PGE 9

10 PI 600 Cast Steel Valves Cast steel valves are designed and manufactured to conform with PI, STM, NSI and other applicable internationally recognised standards, to possess all the qualities to meet with stringent requirement criteria of petroleum, petro-chemical and general industrial applications. Valves are tested in accordance with applicable PI standards. Full traceability is maintained. Valves offer the option of hard facing on the wedge (disc) and seating areas. Lantern rings are furnished as a standard on gate valves of class 300 and above in larger sizes. Gate Valves are optionally available with lantern rings. These rings along with double packing provide a leak-off connection. longside are illustrations of lantern rings as well as disc connection. Fugitive Emission Service PV offers fugitive emission service valves on special request. The valves comply with environmental protection requirements. PV fugitive emission valves are designed, manufactured and tested to meet less than 100ppm. Furthermore, optional live-loading of packing bolts is available. Two sets of plate springs maintain a permanent packing stress of psi. Live-loading extends low emission service life especially in service with high pressure/temperature transients. The stem on all PV fugitive emission service valves is surface finished to RMS. Straightness and roundness are precisely controlled. The stuffing box has a maximum 32 RMS surface finish. Cylindricity and verticality are precisely controlled. General Design Specifications MERICN STD. Shell wall thickness and general valve design specifications PI 600 BRITISH STD. BS1414 (Gate Valve) BS1873 (Globe Valve) BS1868 (Check Valve) Pressure-temperature ratings Face-to-face & End to end dimensions NSI B16.34 NSIB16.10 BS1560 BS2080 Flanged end dimensions NSI B16.5* BS1560 Welding end dimensions NSI B16.25 BS1414 (Gate Valve) BS1873 (Globe Valve) BS1868 (Check Valve) *Valves 28 and larger according to MSS SP-44 or PI 605 are available. PGE 11

11 Bolted Bonnet Gate Valves Features Full body wedge guides allow correct wedge alignment. Yoke sleeve with bearings reduce torque for easy operation. Seat rings allow easy access for maintenance and packing replacement is simple. Soft seated trim option ll gate valves are available with optional PTFE seat rings. The molded PTFE ring is bonded into a seat ring groove in the face for maximum service life. This design is excellent for lower temperature service where tight shutoff is required Parallel slide style also available, see page Handw heel 2. Rising Stem - provides open-close indication 3. Grease Fitting - to minimise wear and operating torque 4. Yoke Sleeve - furnished in ductile Ni-resist or aluminumbronze for low torque operation 5. Swing Bolt - easier maintenance and packing replacement 6. Gland - flange is self-aligning to eliminate stem damage 7. Stuffing Box 8. Stem - upset forge T-head stems to eliminate possibility of a bent stem jamming the valve 9. Backseat - provides back-up stem seal. 10. Bonnet Joint 11. Body - full ported, heavy wall body PI 600 wall thickness 12. Wedge - heavy pattern. vailable in solid & flex wedge 13. Seat Ring - full ported rings for easy maintenance. 14. End Connections - flanged or butt weld ends Grease injector and lantern ring option Soft seated ST trim option PGE 14

12 Bolted Bonnet Globe Valves Operation Seat rings are easily accessible for repair or replacement. Packing bolts on most valves simplify packing replacement. ustralian Pipeline Valve globe valves are for services requiring frequent operation and throttling where pressure drop across the valve is about 20%. Closer throttling, can result in higher pressure drops which may cause excessive velocities or cavitation and could cause vibration or high noise levels resulting in damage to the valve or adjacent components/structure Life Heavy construction provides years of reliable service. Design vailable in bolted and pressure seal bonnet, outside screw and yoke, rising stem with ball or plug type disc, and have flanged or butt weld ends. Standards BS 1873 and NSI B Dimensions to NSI B16.10, BS 2080 and ISO Wall thickness complies with PI Yoke Sleeve - furnished in aluminum-bronze to reduce torque. Larger sizes furnished with bearings. 2. Handwheel 3. Swing Bolts - easier maintenance 4. Gland - self-aligning to eliminate stem damage 5. Stuffing Box 6. Stem - heavy duty 7. Backseat - provides back-up stem seal 8. Bonnet Joint - ring joint or spiral according to NSI class 9. Seat Rings - separate heavy duty, full ported rings for easy maintenance. 10. Disc - heavy duty disc plug design 11. End Connections - flanged or butt weld ends 12. Body - full ported, with PI 600 heavy wall thickness PGE 15

13 Bolted Bonnet Check Valves ustralian Pipeline Valve valves are designed to provide fast valve action and maximum life. ll valves are full ported, have full PI 600 wall thickness, and meet the requirements of NSI B Full opening PI6D (piggable) type also available on request. Features Check valves are designed to close quickly in either horizontal or vertical (flow up) pipe runs. The body seat ring is installed on a 3 o angle. This allows our check valve to close even when installed in horizontal pipe run with no pressure. 1. Disc Stop - provides positive stop in open position 2. Bonnet Joint - (ring or spiral according to class) 3. Hinge Pin - solid pin for maximum strength 4. Securing Lugs - allow disc to seat freely and prevent disc spinning 5. Hinge - designed to withstand shock and load of quick closing 6. Disc - disc is bolted and pinned to hinge; ground seating surface is mated to seat ring for positive shutoff. 7. Seat Ring - Full port seal welded or screwed 8. End Connections - flanged or buttweld PGE 16

14 Pressure Seal Bonnet Valves Flexible Wedge Gate Valve The wedge is a one piece, fully guided wedge. vailable in flex wedge and solid wedge. (Flexible wedge allows the seating faces to move to compensate for thermal expansion). Wedging actions allows a tight seal even in low differential pressure services. Flexible wedge construction resists wedge sticking in service where the valve may be closed when hot and opened when cold. Seating surfaces are hardfaced for long life See Exploded view 6 Parallel slide also available, see page 18 and Yoke Sleeve - aluminum-bronze yoke sleeve has thrust bearings to minimise torque. 2. Hand Wheel - (or gear in larger sizes) 3. Yoke - offering ease of maintenance 4. Stem - The design allows the wedge to self-align, eliminating the possibility of jamming the wedge. 5. Gland - two piece, self-aligning gland eliminates cocking. Swing out bolting facilitates maintenance. 6. Back Seat - Integral, hardfaced 7. Pressure Seal - retaining ring and mild steel silver plated gasket to aid disassembly and provide maximum seal. 8. Seat Ring - hardfaced seat rings are welded to body. Tapered design provides clear flow path. 9. Wedge - one-piece, fully guided. Parallel seat also available. 10. Body - streamlined flow path minimises pressure drop. PI 600 wall thickness. 11. Segment RIng 12. Thrust RIng 13. Gasket 14. Body 15. Bonnet Exploded View Flexible Wedge PGE 17

15 Pressure Seal Bonnet Valves Parallel Slide Gate Valves Normally utilised for shut off service but are not recommended for throttling. Gate valves are normally installed in horizontal pipe runs with the valve stem vertically up. They can be installed in horizontal or vertical pipe runs. fter closing with sufficient force, the stem should be backed off slightly ( 1 /8 turn) to relieve stem load. Parallel Slide Valves have self aligning discs with no wedging force and react freely to thermal changes. The design also ensures uniform seat wear and ease of maintenance. Parallel Slide Gate Valves are ideal where high differential pressure or thermal expansion may cause sticking of wedge to gate in traditional gate valves Yoke Sleeve - aluminum-bronze yoke sleeve with thrust bearings for ease of opening. 2. ctuation - Low torque seating design reduces actuation costs. 3. Yoke - designed to offer ease of maintenance 4. Stem - Threaded into disc housing and also pinned. 5. Gland - two piece, self-aligning gland eliminates cocking. Swing out bolting facilitates maintenance. 6. Back Seat - Integral, hardfaced 7. Pressure Seal - retaining ring and mild steel silver plated gasket to aid disassembly and provide maximum seal. 8. Seat Ring - hardfaced seat rings are welded to body and are designed for ease of maintenance. 9. Discs - Spring loaded discs are self-aligning and reduce actuator torque requirements. 10. Integral Stop - Integral stop positions for reliable seating. PGE 18

16 Pressure Seal Bonnet Valves Globe & SDNR Check Valves ustralian Pipeline Valve Globe valves are installed with pressure and flow under the disc. Globe valves are suitable for most throttling applications; they should not be used for throttling at less than 10% open. Stop Check Valves have a guided loose disc allowing the valve to act as a combination globe valve and check valve Yoke Sleeve - aluminum-bronze yoke sleeve minimizes operating torque. Larger sizes have needle bearing type thrust bearings. 2. ctuation - Manual handwheel gear operator or actuated. 3. Yoke - designed to offer ease of maintenance. 4. Stem - precision-ground stem has upset tee-head for reliable stem/wedge connection. 5. Gland - two piece, self-aligning gland eliminates cocking. Swing out bolting facilitates maintenance. 6. Back Seat - Integral, hardfaced 7. Pressure Seal - uncomplicated design has segmented retaining ring and mild steel silver plated gasket to aid disassembly and provide maximum bonnet seal. 8. Hardened Seating Surfaces - both disc and body seating surfaces are hard faced for maximum service life. 9. Disc - fully body guided for positive seating. 10. Body - Full port s pattern design available to minimise pressure drop. PGE 19

17 Pressure Seal Bonnet Valves Tilt & Piston Check Valves ustralian Pipeline Valve Check valves are installed with pressure and flow under the disc Pressure seal design - with retaining ring. 2. Guided disc - for positive seating. 3. Welded in - hardfaced seat ring. 4. Full port - S pattern flow path available to minimise pressure drop. PGE 20

18 Gate Valve Cat XXXP47XXXX-XX Class 150 Full Port Design Description Material Specs. Body Carbon Steel 216 Gr. WCB Bonnet Carbon Steel 216 Gr. WCB Disc Facing Stainless Steel 182 Gr. F6a/CR13 or Stellite/HF Stem Stainless Steel 276 Gr.410 or 182 Gr. F6a/CR13 Hand Wheel Ductile Iron 536 Gr Seat Ring Stainless Steel 182 Gr. F6a/CR13, Stellite/HF Back Seat Ring Stainless Steel 276 Gr. 410 or 182 Gr. F6a Yoke Sleeve Ductile Iron or Bronze 439 Gr. D2C or B62 Sleeve Gland Carbon Steel 216 Gr. WCB Gland Flange Carbon Steel 105 Gland Ring Stainless Steel 182 Gr. F6a Wheel Nut Carbon Steel 105 Bonnet Bolt Carbon Steel 193 Gr. B7/B7M Bonnet Nut Carbon Steel 194 Gr. 2H/2HM Gland Bolt Carbon Steel 193 Gr. B7 Gland Nut Carbon Steel 194 Gr. 2H Gland Bolt Pin Carbon Steel 108 Gr Bearing - Thrust Ball Grease Nipple Carbon Steel 307 Gr. B Set Screw Carbon Steel 307 Gr. B Name Plate Stainless Steel 304/L Packing sbestos Free Reinforced Graphite Gasket Spiral Wound 304/316 Graphite filled B C Standards Face to Face/End to End NSI B16.10 Flange Dimensions NSI B16.5/26 & larger MSS SP-44 Basic Design PI 600 Testing PI 598 Size (in) Face to Face RF End to End BW B. Valve Open C. Hand Wheel Dia Weight (Kg) RF * For 1 2 to 1 dimensions see page 41 and detailed overview brochure. Size (in) Face to Face RF End to End BW B. Valve Open C. Hand Wheel Dia Weight (Kg) RF * For 1 2 to 1 dimensions see page 41 and detailed overview brochure. For CF8/CF8M 150lb gate see page 41. * For Buttweld weights see detailed overview brochure. PGE 21 (BW)

19 Gate Valve Cat XXXP33XXXX-XX Class 300 Full Port Design Description Material Specs. Body Carbon Steel 216 Gr. WCB Bonnet Carbon Steel 216 Gr. WCB Disc Facing Stainless Steel 182 Gr. F6a/CR13 or Stellite/HF Stem Stainless Steel 276 Gr.410 or 182 Gr. F6a/CR13 Hand Wheel Ductile Iron 536 Gr Seat Ring Stainless Steel 182 Gr. F6a/CR13, Stellite/HF Back Seat Ring Stainless Steel 276 Gr. 410 or 182 Gr. F6a Yoke Sleeve Ductile Iron or Bronze 439 Gr. D2C or B62 Sleeve Gland Carbon Steel 216 Gr. WCB Gland Flange Carbon Steel 105 Gland Ring Stainless Steel 182 Gr. F6a Wheel Nut Carbon Steel 105 Bonnet Bolt Carbon Steel 193 Gr. B7/B7M Bonnet Nut Carbon Steel 194 Gr. 2H/2HM Gland Bolt Carbon Steel 193 Gr. B7 Gland Nut Carbon Steel 194 Gr. 2H Gland Bolt Pin Carbon Steel 108 Gr Bearing - Thrust Ball Grease Nipple Carbon Steel 307 Gr. B Set Screw Carbon Steel 307 Gr. B Name Plate Stainless Steel 304/L Packing sbestos Free Reinforced Graphite Gasket Spiral Wound 304/316 Graphite filled B C Standards Face to Face/End to End NSI B16.10 Flange Dimensions NSI B16.5 Basic Design PI 600 Testing PI 598 Size (in) Face to Face RF End to End BW B. Valve Open C. Hand Wheel Dia Weight (Kg) RF * For 1 2 to 1 dimensions see page 42 and detailed overview brochure. For RTJ & 5 dimensions see detailed overview brochure. Size (in) Face to Face RF End to End BW B. Valve Open C. Hand Wheel Dia Weight (Kg) RF * For CF8/CF8M 300Lb gate see page 42. * For Buttweld weights see detailed overview brochure. PGE 22 (BW)

20 Gate Valve Cat XXXP76XXXX-XX Class 600 Full Port Design Description Material Specs. Body Carbon Steel 216 Gr. WCB Bonnet Carbon Steel 216 Gr. WCB Disc Facing Stainless Steel 182 Gr. F6a/CR13 or Stellite/HF Stem Stainless Steel 276 Gr.410 or 182 Gr. F6a/CR13 Hand Wheel Ductile Iron 536 Gr Seat Ring Stainless Steel 182 Gr. F6a/CR13, Stellite/HF Back Seat Ring Stainless Steel 276 Gr. 410 or 182 Gr. F6a Yoke Sleeve Ductile Iron or Bronze 439 Gr. D2C or B62 Sleeve Gland Carbon Steel 216 Gr. WCB Gland Flange Carbon Steel 105 Gland Ring Stainless Steel 182 Gr. F6a Wheel Nut Carbon Steel 105 Bonnet Bolt Carbon Steel 193 Gr. B7/B7M Bonnet Nut Carbon Steel 194 Gr. 2H/2HM Gland Bolt Carbon Steel 193 Gr. B7 Gland Nut Carbon Steel 194 Gr. 2H Gland Bolt Pin Carbon Steel 108 Gr Bearing - Thrust Ball Grease Nipple Carbon Steel 307 Gr. B Set Screw Carbon Steel 307 Gr. B Name Plate Stainless Steel 304/L Packing sbestos Free Reinforced Graphite Gasket Metal Ring Joint or Spiral Wound SS Graphite filled Standards Face to Face/End to End NSI B16.10 Flange Dimensions NSI B16.5 Basic Design PI 600 Testing PI 598 Size (in) Face to Face RF Face to Face RTJ End to End BW B. Valve Open C. Hand Wheel Dia Weight (Kg) RF Weight (Kg) BW Size (in) Face to Face RF Face to Face RTJ End to End BW B. Valve Open C. Hand Wheel Dia Weight (Kg) RF Weight (Kg) BW For 5 and 26 to 36 dimensions see detailed overview brochure. B C (BW) PGE 23

21 Gate Valve Cat XXXP83XXXX-XX Class 900 Full Port Design Description Material Specs. Body Carbon Steel 216 Gr. WCB Bonnet Carbon Steel 216 Gr. WCB Disc Facing Stainless Steel 182 Gr. F6a/CR13 or Stellite/HF Stem Stainless Steel 276 Gr.410 or 182 Gr. F6a/CR13 Hand Wheel Ductile Iron 536 Gr Seat Ring Carbon Steel Stellite/HF Back Seat Ring Stainless Steel 182 Gr. F6a Yoke Sleeve Ductile Iron or Bronze 439 Gr. D2C or B62 Sleeve Gland Carbon Steel 216 Gr. WCB Gland Flange Carbon Steel 105 Gland Ring Stainless Steel 182 Gr. F6a Wheel Nut Carbon Steel 105 Bonnet Bolt Carbon Steel 193 Gr. B7/B7M Bonnet Nut Carbon Steel 194 Gr. 2H/2HM Gland Bolt Carbon Steel 193 Gr. B7/B7M Gland Nut Carbon Steel 194 Gr. 2H.2HM Gland Bolt Pin Carbon Steel 108 Gr Bearing - Thrust Ball Grease Nipple Carbon Steel 307 Gr. B Set Screw Carbon Steel 307 Gr. B Name Plate Stainless Steel 304/L Packing sbestos Free Reinforced Graphite Gasket Metal Ring Joint or Spiral Wound SS, Graphite filled C B Standards Face to Face/End to End NSI B16.10 Flange Dimensions NSI B16.5 Basic Design* PI 600, NSI B16.34 Testing PI 598 *10 and over sizes are according to NSI B16.34 Size (in) Face to Face RF/BW Face to Face RTJ B. Valve Open C. Hand Wheel Dia Weight (Kg) RF Weight (Kg) BW Note: 900 LB 2 & are the same as 1500 LB 2 & Size (in) 20. Face to Face RF Face to Face RTJ 1333 B. Valve Open 2440 C. Hand Wheel Dia 760 Weight (Kg) RF 4860 Weight (Kg) BW 4050 For 5 and 24 dimensions & weights see detailed overview brochure. PGE 24 (BW)

22 Gate Valve Cat XXXP87XXXX-XX Class 1500 Full Port Design Description Material Specs. Body Carbon Steel 216 Gr. WCB Bonnet Carbon Steel 216 Gr. WCB Disc Facing Stainless Steel 182 Gr. F6a/CR13 or Stellite/HF Stem Stainless Steel 276 Gr.410 or 182 Gr. F6a/CR13 Hand Wheel Ductile Iron 536 Gr Seat Ring Carbon Steel Stellite/HF Back Seat Ring Stainless Steel 182 Gr. F6a Yoke Sleeve Ductile Iron or Bronze 439 Gr. D2C or B62 Sleeve Gland Carbon Steel 216 Gr. WCB Gland Flange Carbon Steel 105 Gland Ring Stainless Steel 182 Gr. F6a Wheel Nut Carbon Steel 105 Zn. Plating Bonnet Bolt Carbon Steel 193 Gr. B7/B7M Bonnet Nut Carbon Steel 194 Gr. 2H/2HM Gland Bolt Carbon Steel 193 Gr. B7/B7M Gland Nut Carbon Steel 194 Gr. 2H/2HM Gland Bolt Pin Carbon Steel 108 Gr Bearing - Thrust Ball Grease Nipple Carbon Steel 307 Gr. B Set Screw Carbon Steel 307 Gr. B Name Plate Stainless Steel 304/L Packing sbestos Free Reinforced Graphite Gasket Metal Ring Joint or Sprial Wound SS Graphite filled Standards Face to Face/End to End NSI B16.10 Flange Dimensions NSI B16.5 Basic Design* PI 600, NSI B16.34 Testing PI 598 *10 and over sizes are according to NSI B16.34 Size (in) Face to Face RF/BW Face to Face RTJ B. Valve Open C. Hand Wheel Dia Weight (Kg) RF Weight (Kg) BW C B Size (in) 20. Face to Face RF Face to Face RTJ Short Pattern End to End BW 1473 B. Valve Open 2440 C. Hand Wheel Dia - Weight (Kg) RF Weight (Kg) Short PatternBW - Long Pattern BW 9560 For 5 and 24 dimensions & weights see detailed overview brochure. PGE 25 (BW)

23 Gate Valve (Pressure Seal) Cat XXXP83PXXXX-XX Class 900 Full Port Design Description Material Specs. Body Carbon Steel 216 Gr. WCB Bonnet Carbon Steel 216 Gr. WCB Disc Facing Stainless Steel 182 Gr. F6a/CR13 or Stellite/HF Stem Stainless Steel 276 Gr.410 or 182 Gr. F6a/CR13 Hand Wheel Ductile Iron 536 Gr Seat Ring Carbon Steel Stellite/HF Yoke Sleeve Ductile Iron or Bronze 439 Gr. D2C or B62 Sleeve Gland Carbon Steel 216 Gr. WCB Gland Flange Carbon Steel 105 Gland Ring Stainless Steel 182 Gr. F6a Wheel Nut Carbon Steel 105 Bonnet Bolt Carbon Steel 193Gr. B7/B7M Bonnet Nut Carbon Steel 194 Gr. 2H/2HM Gland Bolt Carbon Steel 193 Gr. B7 Gland Nut Carbon Steel 194 Gr. 2H Gland Bolt Pin Carbon Steel 108 Gr Bearing - Thrust Ball Grease Nipple Carbon Steel 307 Gr. B Set Screw Carbon Steel 307 Gr. B Name Plate Stainless Steel 304/L Packing sbestos Free Reinforced Graphite Gasket Soft Metal Ring CD Plated Standards Face to Face/End to End NSI B16.10 Flange Dimensions NSI B16.5 Basic Design* PI 600, NSI B16.34 Testing PI 598 *Note: 10 and over sizes are according to NSI B16.34 Size (in) Face to Face RF/BW Face to Face RTJ Short Pattern End to End BW B. Valve Open C. Hand Wheel Dia Weight (Kg) Short Pattern BW Weight (Kg) Long Pattern BW Weight (Kg) Long Pattern RF Note: 900 LB 2 & are the same as 1500 LB 2 & Size (in) 20. Face to Face RF/BW Face to Face RTJ Short Pattern End to End BW - B. Valve Open 760 C. Hand Wheel Dia - Weight (Kg) Short PatternBW 3636 Weight (Kg) Long PatternBW 4050 Weight (Kg) RF 4860 For 5 and 24 (Long Pattern) dimensions see detailed overview brochure. PGE 26 B C (BW)

24 Gate Valve (Pressure Seal) Cat XXXP87PXXXX-XX Class 1500 Full Port Design Description Material Specs. Body Carbon Steel 216 Gr. WCB Bonnet Carbon Steel 216 Gr. WCB Disc Facing Stainless Steel 182 Gr. F6a/CR13 or Stellite/HF Stem Stainless Steel 276 Gr.410 or 182 Gr. F6a/CR13 Hand Wheel Ductile Iron 536 Gr Seat Ring Carbon Steel Stellite/HF Yoke Sleeve Ductile Iron or Bronze 439 Gr. D2C or B62 Sleeve Gland Carbon Steel 216 Gr. WCB Gland Flange Carbon Steel 105 Gland Ring Stainless Steel 182 Gr. F6a Wheel Nut Carbon Steel 105 Zn. Plating Bonnet Bolt Carbon Steel 193 Gr. B7/B7M Bonnet Nut Carbon Steel 194 Gr. 2H/2HM Gland Bolt Carbon Steel 193 Gr. B7/B7M Gland Nut Carbon Steel 194 Gr. 2H/2HM Gland Bolt Pin Carbon Steel 108 Gr Bearing - Thrust Ball Grease Nipple Carbon Steel 307 Gr. B Set Screw Carbon Steel 307 Gr. B Name Plate Stainless Steel 304/L Packing sbestos Free Reinforced Graphite Gasket Soft Metal Ring CD Plated Standards Face to Face/End to End NSI B16.10 Flange Dimensions NSI B16.5 Basic Design* PI 600, NSI B16.34 Testing PI 598 *Note: 10 and over sizes are according to NSI B16.34 Size (in) Face to Face RF/BW Face to Face RTJ Short Pattern End to End BW B. Valve Open C. Hand Wheel Dia Weight (Kg) Short Pattern BW Weight (Kg) Long Pattern BW Weight (Kg) Long Pattern RF Size (in) 20. Face to Face RF/BW Face to Face RTJ Short Pattern End to End BW 1473 B. Valve Open 2440 C. Hand Wheel Dia - Weight (Kg) Short PatternBW 7980 Weight (Kg) Long PatternBW 9560 Weight (Kg) RF For 5 and 24 (Long Pattern) dimensions see detailed overview brochure. PGE 27 B C (BW)

25 Globe Valve Cat XXXP143XXXX-XX Class 150 Full Port Design Description Material Specs. Body Carbon Steel 216 Gr. WCB Bonnet Carbon Steel 216 Gr. WCB Disc Facing Stainless Steel 182 Gr. F6a/CR13 or Stellite/HF Stem Stainless Steel 276 Gr.410 or 182 Gr. F6a Hand Wheel Ductile Iron 536 Gr Seat Ring Stainless Steel 182 Gr. F6a/CR13, Stellite/HF Back Seat Ring Stainless Steel 276 Gr.410 or 182 Gr. F6a Gland Flange Carbon Steel 105 Gland Ring Stainless Steel 182 Gr. F6a Disc Gland Stainless Steel 217 Gr. C-15 Yoke Bush Ductile Iron or Bronze 439 Gr. D2C or B62 Bonnet Bolt Carbon Steel 193 Gr. B7/B7M Bonnet Nut Carbon Steel 194 Gr. 2H/2HM Gland Bolt Carbon Steel 193 Gr.B7 Gland Nut Carbon Steel 194 Gr. 2H Gland Bolt Pin Carbon Steel 108 Gr Wheel Nut Stainless Steel 192 Gr. 8/105 Name Plate Stainless Steel 304/L Packing sbestos Free Reinforced Graphite Gasket Spiral Wound 304/316 Graphite filled B C Standards Face to Face/End to End NSI B16.10 Flange Dimensions NSI B16.5 Basic Design PI 600* Testing PI 598 *Stem is Based on B.S 1873 Size (in) Face to Face RF End to End BW B. Valve Open C. Hand Wheel Dia Weight (Kg) RF Weight (Kg) BW For RTJ dimensions and 5 dimensions, see detailed overview brochure. For 1/2 to 1 1/2 see page 43 and detailed overview brochure. For CF8/CF8M Globe 150Lb see page 43. (BW) PGE 28

26 Globe Valve Cat XXXP151XXXX-XX Class 300 Full Port Design Description Material Specs. Body Carbon Steel 216 Gr. WCB Bonnet Carbon Steel 216 Gr. WCB Disc Facing Stainless Steel 182 Gr. F6a/CR13 or Stellite/HF Stem Stainless Steel 276 Gr.410 or 182 Gr. F6a Hand Wheel Ductile Iron 536 Gr Seat Ring Stainless Steel 182 Gr. F6a/CR13, Stellite/HF Back Seat Ring Stainless Steel 276 Gr.410 or 182 Gr. F6a Gland Flange Carbon Steel 105 Gland Ring Stainless Steel 182 Gr. F6a/276 Gr.410 Disc Gland Stainless Steel 217 Gr. C-15/276 Gr.410 Yoke Bush Stainless Steel or Bronze 439 Gr. D2C or B62 Bonnet Bolt Carbon Steel 193 Gr. B7/B7M Bonnet Nut Carbon Steel 194 Gr. 2H/2HM Gland Bolt Carbon Steel 193 Gr.B7/2HM Gland Nut Carbon Steel 194 Gr. 2H Gland Bolt Pin Carbon Steel 108 Gr Wheel Nut Stainless Steel 194 Gr. 8/105 Name Plate Stainless Steel 304/L Packing sbestos Free Reinforced Graphite Gasket Spiral Wound 304/316 Graphite filled B C Standards Face to Face/End to End NSI B16.10 Flange Dimensions NSI B16.5 Basic Design PI 600* Testing PI 598 *Stem is Based on B.S 1873 Size (in) Face to Face RF End to End BW B. Valve Open C. Hand Wheel Dia Weight (Kg) RF Weight (Kg) BW For RTJ dimensions 2-16 and 5 RF/RTJ dimensions, see detailed overview brochure. For 1 2 to see page 43 and detailed overview brochure. For CF8/CF8M Globe 300# see page 43. (BW) PGE 29

27 Globe Valve Cat XXXP171XXXX-XX Class 600 Full Port Design Description Material Specs. Body Carbon Steel 216 Gr. WCB Bonnet Carbon Steel 216 Gr. WCB Disc Facing Stainless Steel 182 Gr. F6a/CR13 or Stellite/HF Stem Stainless Steel 276 Gr.410 or 182 Gr. F6a/CR13 Hand Wheel Ductile Iron 536 Gr Seat Ring Stainless Steel 182 Gr. F6a/CR13, Stellite/HF Back Seat Ring Stainless Steel 276 Gr.410 or 182 Gr. F6a Gland Flange Carbon Steel 105 Gland Ring Stainless Steel 182 Gr. F6a Disc Gland Stainless Steel 217 Gr. C-15 Yoke Bush Ductile Iron or Bronze 439 Gr. D2C or B62 Bonnet Bolt Carbon Steel 193 Gr. B7/B7M Bonnet Nut Carbon Steel 194 Gr. 2H/2HM Gland Bolt Carbon Steel 193 Gr. B7 Gland Nut Carbon Steel 194 Gr. 2H Gland Bolt Pin Carbon Steel 108 Gr Wheel Nut Stainless Steel 194 Gr. 8/105 Name Plate Stainless Steel 304/L Packing sbestos Free Reinforced Graphite Gasket Metal Ring Joint or Spiral Wound SS Graphite filled B C Standards Face to Face/End to End NSI B16.10 Flange Dimensions NSI B16.5 Basic Design PI 600* Testing PI 598 *Stem is Based on B.S 1873 Size (in) Face to Face RF Face to Face RTJ End to End BW B. Valve Open C. Hand Wheel Dia Weight (Kg) RF Weight (Kg) BW For 1 2 to see detailed overview brochure. (BW) PGE 30

28 Globe Valve Cat XXXP183XXXX-XX Class 900 Full Port Design Description Material Specs. Body Carbon Steel 216 Gr. WCB Bonnet Carbon Steel 216 Gr. WCB Disc Facing Stainless Steel 182 Gr. F6a/CR13 or Stellite/HF Stem Stainless Steel 276 Gr.410 or 182 Gr. F6a/CR13 Hand Wheel Ductile Iron 536 Gr Seat Ring Stainless Steel 182 Gr. F6a/CR13, Stellite/HF Back Seat Ring Stainless Steel 276 Gr.410 or 182 Gr. F6a Gland Flange Carbon Steel 105 Gland Ring Stainless Steel 182 Gr. F6a Disc Gland Stainless Steel 217 Gr. C-15 Yoke Bush Ductile Iron or Bronze 439 Gr. D2C or B62 Bonnet Bolt Carbon Steel 193 Gr. B7/B7M Bonnet Nut Carbon Steel 194 Gr. 2H/2HM Gland Bolt Carbon Steel 193 Gr. B7 Gland Nut Carbon Steel 194 Gr. 2H Gland Bolt Pin Carbon Steel 108 Gr Wheel Nut Stainless Steel 194 Gr. 8/105 Name Plate Stainless Steel 304/L Packing sbestos Free Reinforced Graphite Gasket Metal Ring Joint or Spiral Wound SS Graphite filled C B Standards Face to Face/End to End NSI B16.10 Flange Dimensions NSI B16.5 Basic Design PI 600* Testing PI 598 *Stem is Based on B.S 1873 Size (in) Face to Face RF/BW Face to Face RTJ Short Pattern End to End BW B. Valve Open C. Hand Wheel Dia Weight (Kg) Short Pattern BW Weight (Kg) Long Pattern BW Weight (Kg) Long Pattern RF Note:- 900 LB 2 & are the same as 1500 LB 2 & Parabolic disc for low torque For 1 2 to dimensions see detailed overview brochure. (BW) PGE 31

29 Globe Valve Cat XXXP189XXXX-XX Class 1500 Full Port Design Description Material Specs. Body Carbon Steel 216 Gr. WCB Bonnet Carbon Steel 216 Gr. WCB Disc Facing Stainless Steel 182 Gr. F6a/CR13 or Stellite/HF Stem Stainless Steel 276 Gr.410 or 182 Gr. F6a/CR13 Hand Wheel Ductile Iron 536 Gr Seat Ring Stainless Steel 182 Gr. F6a/CR13, Stellite/HF Back Seat Ring Carbon Steel 276 Gr.410 or 182 Gr. F6a Gland Flange Carbon Steel 105 Gland Ring Stainless Steel 182 Gr. F6a Disc Gland Stainless Steel 217 Gr. C-15 Yoke Bush Ductile Iron or Bronze 439 Gr. D2C or B62 Bonnet Bolt Carbon Steel 193 Gr. B7/B7M Bonnet Nut Carbon Steel 194 Gr. 2H/2HM Gland Bolt Carbon Steel 193 Gr. B7 Gland Nut Carbon Steel 194 Gr. 2H Gland Bolt Pin Carbon Steel 108 Gr Wheel Nut Stainless Steel 194 Gr. 8/105 Name Plate Stainless Steel 304/L Packing sbestos Free Reinforced Graphite Gasket Metal Joint or Spiral Wound SS Graphite filled C B Standards Face to Face/End to End NSI B16.10 Flange Dimensions NSI B16.5 Basic Design PI 600* Testing PI 598 *Stem is based on B.S Size (in) Face to Face RF/BW Face to Face RTJ Short Pattern End to End BW B. Valve Open C. Hand Wheel Dia Weight (Kg) Short Pattern BW Weight (Kg) Long Pattern BW Weight (Kg) Long Pattern RF Parabolic disc for low torque For 1 2 to dimensions see detailed overview brochure. (BW) PGE 32

30 Globe Valve (Pressure Seal Bonnet) Cat XXXP183PXXXX-XX Class 900 Full Port Design Description Material Specs. Body Carbon Steel 216 Gr. WCB Bonnet Carbon Steel 216 Gr. WCB Disc Facing Stainless Steel 182 Gr. F6a/CR13 or Stellite/HF Stem Stainless Steel 276 Gr.410 or 182 Gr. F6a/CR13 Hand Wheel Ductile Iron 536 Gr Seat Ring Stainless Steel 182 Gr. F6a/CR13, Stellite/HF Back Seat Ring Stainless Steel 276 Gr.410 or 182 Gr. F6a Gland Flange Carbon Steel 105 Gland Ring Stainless Steel 182 Gr. F6a Disc Gland Stainless Steel 217 Gr. C-15 Yoke Bush Ductile Iron or Bronze 439 Gr. D2C or B62 Gland Bolt Carbon Steel 193 Gr. B7/B7M Gland Nut Carbon Steel 194 Gr. 2H/2HM Gland Bolt Pin Carbon Steel 108 Gr Wheel Nut Stainless Steel 194 Gr. 8/105 Bonnet Bolt Carbon Steel 193 Gr. B7/B7M Bonnet Nut Carbon Steel 194 Gr. 2H/2HM Name Plate Stainless Steel 304/L Packing sbestos Free Reinforced Graphite Gasket Soft Metal Ring CD Plated B C Standards Face to Face/End to End NSI B16.10 Flange Dimensions NSI B16.5 Basic Design PI 600* Testing PI 598 *Stem is Based on B.S 1873 Size (in) Face to Face RF/BW Face to Face RTJ Short Pattern End to End BW B. Valve Open C. Hand Wheel Dia Weight (Kg) Short Pattern BW Weight (Kg) Long Pattern BW Weight (Kg) Long Pattern RF Note 900 LB 2 & are the same as 1500 LB 2 & Parabolic disc for low torque For 1 2 to dimensions see detailed overview brochure. (BW) PGE 33

31 Globe Valve (Pressure Seal Bonnet) Cat XXXP189PXXXX-XX Class 1500 Full Port Design Description Material Specs. Body Carbon Steel 216 Gr. WCB Bonnet Carbon Steel 216 Gr. WCB Disc Facing Stainless Steel 182 Gr. F6a/CR13 or Stellite/HF Stem Stainless Steel 276 Gr.410 or 182 Gr. F6a/CR13 Hand Wheel Ductile Iron 536 Gr Seat Ring Stainless Steel 182 Gr. F6a/CR13, Stellite/HF Back Seat Ring Stainless Steel 276 Gr.410 or 182 Gr. F6a Gland Flange Carbon Steel 105 Gland Ring Stainless Steel 182 Gr. F6a Disc Gland Stainless Steel 217 Gr. C-15 Yoke Bush Ductile Iron or Bronze 439 Gr. D2C or B62 Gland Bolt Carbon Steel 193 Gr. B7/B7M Gland Nut Carbon Steel 194 Gr. 2H/2HM Gland Bolt Pin Carbon Steel 108 Gr Wheel Nut Stainless Steel 194 Gr. 8/105 Bonnet Bolt Carbon Steel 193 Gr. B7/B7M Bonnet Nut Carbon Steel 194 Gr. 2H/2HM Name Plate Stainless Steel 304/L Packing sbestos Free Reinforced Graphite Gasket Soft Metal Ring CD Plated B C Standards Face to Face/End to End NSI B16.10 Flange Dimensions NSI B16.5 Basic Design PI 600* Testing PI 598 *Stem is Based on B.S 1873 Size (in) Face to Face RF/BW Face to Face RTJ Short Pattern End to End BW B. Valve Open C. Hand Wheel Dia Weight (Kg) Short Pattern BW Weight (Kg) Long Pattern BW Weight (Kg) Long Pattern RF Note 900 LB 2 & are the same as 1500 LB 2 & Parabolic disc for low torque For 1 2 to dimensions see detailed overview brochure. (BW) PGE 34

32 Swing Check Valve Cat XXXP147XXXX-XX Class 150 Full Port Design Description Material Specs. Body Carbon Steel 216 Gr. WCB Cover Carbon Steel 216 Gr. WCB Disc Facing Stainless Steel 182 Gr. F6a/CR13 or Stellite/HF Hinge Carbon Steel 276 Gr. 410 or 182 Gr. F6a/CR13 Hinge Pin Stainless Steel 182 Gr. F6a/CR13 Seat Ring Stainless Steel 182 Gr. F6a/CR13, Stellite/HF Plug Carbon Steel 108 Gr Cover Bolt Carbon Steel 193 Gr. B7/B7M Cover Nut Stainless Steel 194 Gr. 2H/2HM Disc Nut Stainless Steel 563 Gr. B Washer Stainless Steel 276 Gr. 410 Eye Bolt Carbon Steel 105 Name Plate Stainless Steel 304 L Gasket Spiral Wound 304/316 Graphite filled B Standards Face to Face/End to End NSI B16.10 Flange Dimensions NSI B16.5 Basic Design PI 600* Testing PI 598 *lso meets design requirements for NSI B16.34 Size (in) Face to Face RF End to End BW B. Height Weight (Kg) RF Weight (Kg) BW Size (in) Face to Face RF End to End BW B. Height Weight (Kg) RF Weight (Kg) BW (BW) For RTJ dimensions see detailed overview brochure. For 5 dimensions see page 44 and detailed overview brochure. For 1 2 to 1 dimensions see page 44 and detailed overview brochure.. For CF8/CF8M 150Lb see page 44. PGE 35

33 Swing Check Valve Cat XXXP159XXXX-XX Class 300 Full Port Design Description Material Specs. Body Carbon Steel 216 Gr. WCB Cover Carbon Steel 216 Gr. WCB Disc Facing Stainless Steel 182 Gr. F6a/CR13 or Stellite/HF Hinge Carbon Steel 216 Gr WCB Hinge Pin Stainless Steel 182 Gr. F6a/CR13 Seat Ring Stainless Steel 182 Gr. F6a/CR13, Stellite/HF Plug Carbon Steel 108 Gr.1045 Cover Bolt Carbon Steel 193 Gr. B7/B7M Cover Nut Carbon Steel 194 Gr. 2H/2HM Disc Nut Carbon Steel 563 Gr. B Washer Stainless Steel 276 Type 410 Eye Bolt Carbon Steel 307 Gr. B Name Plate Stainless Steel 304/L Gasket Spiral Wound 304/316 Graphite filled B Standards Face to Face/End to End NSI B16.10 Flange Dimensions NSI B16.5 Basic Design PI 600 Testing PI 598 *lso meets design requirements for NSI B16.34 Size (in) Face to Face RF End to End BW B. Height Weight (Kg) RF Weight (Kg) BW Size (in) Face to Face RF End to End BW B. Height Weight (Kg) RF Weight (Kg) BW For RTJ dimensions see detailed overview brochure. For 5 dimensions see page 44 and detailed overview brochure. For 1 2 to 1 dimensions see page 44 and detailed overview brochure. For CF8/CF8M 300Lb see page 44. (BW) PGE 36

34 Swing Check Valve Cat XXXP175XXXX-XX Class 600 Full Port Design Description Material Specs. Body Carbon Steel 216 Gr. WCB Cover Carbon Steel 216 Gr. WCB Disc Facing Stainless Steel 182 Gr. F6a/CR13 or Stellite/HF Hinge Carbon Steel 216 Gr WCB Hinge Pin Stainless Steel 182 Gr. F6a/CR13 Seat Ring Stainless Steel 182 Gr. F6a/CR13, Stellite/HF Plug Carbon Steel 108 Gr.1045 Cover Bolt Carbon Steel 193 Gr. B7/B7M Cover Nut Carbon Steel 194 Gr. 2H/2HM Disc Nut Carbon Steel 563 Gr. B Washer Stainless Steel 276 Type 410 Eye Bolt Carbon Steel 307 Gr. B Name Plate Stainless Steel 304/L Gasket Metal Ring Joint or Spiral Wound SS Graphite filled B Standards Face to Face/End to End NSI B16.10 Flange Dimensions NSI B16.5 Basic Design* PI 600 Testing PI 598 *lso meets design requirements for NSI B16.34 Size (in) Face to Face RF Face to Face RTJ End to End BW B. Height Weight (Kg) RF Weight (Kg) BW Size (in) Face to Face RF (BW). Face to Face RTJ End to End BW B. Height Weight (Kg) RF Weight (Kg) BW PGE 37

35 Swing Check Valve Cat XXXP187XXXX-XX Class 900 Full Port Design Description Material Specs. Body Carbon Steel 216 Gr. WCB Cover Carbon Steel 216 Gr. WCB Disc Facing Stainless Steel 182 Gr. F6a/CR13 or Stellite/HF Hinge Carbon Steel 216 Gr WCB Hinge Pin Stainless Steel 182 Gr. F6a/CR13 Seat Ring Stainless Steel 182 Gr. F6a/CR13, Stellite/HF Plug Carbon Steel 108 Gr.1045 Bonnet Bolt Carbon Steel 193 Gr. B7/B7M Bonnet Nut Carbon Steel 194 Gr. 2H/2HM Disc Nut Carbon Steel 563 Gr. B Washer Stainless Steel 276 Type 410 Eye Bolt Carbon Steel 307 Gr. B Name Plate Stainless Steel 304/L Gasket Metal Ring Joint or Spiral Wound SS Graphite filled B Standards Face to Face/End to End NSI B16.10 Flange Dimensions NSI B16.5 Basic Design* PI 600 Testing PI 598 *10 and over sizes are according to NSI B16.34 ll sizes meet the design requirements for NSI B16.34 Size (in) Face to Face RF/BW Face to Face RTJ Face to Face Short Pattern BW B. Height Weight (Kg) Short Pattern BW Weight (Kg) Long Pattern BW Weight (Kg) Long Pattern RF Size (in) 20. Face to Face RF/BW Face to Face RTJ 1334 B. Height 867 Weight (Kg) Long Pattern BW 3100 Weight (Kg) Long Pattern RF 3500 (BW) PGE 38

36 Swing Check Valve Cat XXXP199XXXX-XX Class 1500 Full Port Design Description Material Specs. Body Carbon Steel 216 Gr. WCB Cover Carbon Steel 216 Gr. WCB Disc Facing Stainless Steel 182 Gr. F6a/CR13 or Stellite/HF Hinge Carbon Steel 216 Gr WCB Hinge Pin Stainless Steel 182 Gr. F6a/CR13 Seat Ring Stainless Steel 182 Gr. F6a/CR13, Stellite/HF Plug Carbon Steel 108 Gr.1045 Bonnet Bolt Carbon Steel 193 Gr. B7/B7M Bonnet Nut Carbon Steel 194 Gr. 2H/2HM Disc Nut Carbon Steel 563 Gr. B Washer Stainless Steel 276 Type 304 Eye Bolt Carbon Steel 307 Gr. B Name Plate Stainless Steel 304/L Gasket Metal Ring Joint or Spiral Wound SS Graphite filled B Standards Face to Face/End to End NSI B16.10 Flange Dimensions NSI B16.5 Basic Design* PI 600 Testing PI 598 *10 and over sizes are according to NSI B16.34 ll sizes meet the design requirements for NSI B16.34 Size (in) Face to Face RF/BW Face to Face RTJ Short Pattern End to End BW B. Height Weight (Kg) Short Pattern BW Weight (Kg) Long Pattern RF Weight (Kg) Long Pattern BW Size (in) 20. Face to Face RF/BW Face to Face RTJ Short Pattern End to End BW - B. Height 2600 Weight (Kg) Short Pattern BW 4809 (BW) PGE 39

37 Swing Check Valve (Pressure Seal Bonnet) Cat XXXP187PXXXX-XX Class 900 Full Port Design Description Material Specs. Body Carbon Steel 216 Gr. WCB Cover Carbon Steel 216 Gr. WCB Disc Facing Stainless Steel 182 Gr. F6a/CR13 or Stellite/HF Hinge Carbon Steel 216 Gr WCB Hinge Pin Stainless Steel 182 Gr. F6a/CR13 Seat Ring Stainless Steel 182 Gr. F6a/CR13, Stellite/HF Plug Carbon Steel 108 Gr.1045 Cover Bolt Carbon Steel 193 Gr. B7/B7M Cover Nut Carbon Steel 194 Gr. 2H/2HM Disc Nut Carbon Steel 563 Gr. B Washer Stainless Steel 276 Type 304 Eye Bolt Carbon Steel 307 Gr. B Name Plate Stainless Steel 304/L Gasket Soft Metal Ring CD Plated B Standards Face to Face/End to End NSI B16.10 Flange Dimensions NSI B16.5 Basic Design* PI 600 Testing PI 598 *10 and over sizes are according to NSI B16.34 ll sizes meet the design requirements for NSI B16.34 Size (in) Face to Face RF/BW Face to Face RTJ Short Pattern End to End BW B. Height Weight (Kg) Short Pattern BW Weight (Kg) Long Pattern BW Weight (Kg) Long Pattern RF Size (in) 20. Face to Face RF/BW Short Pattern End to End BW - B. Height 867 Weight (Kg) BW 3103 Weight (Kg) Long Pattern RF 3500 (BW) PGE 40

38 Swing Check Valve (Pressure Seal Bonnet) Cat XXXP199PXXXX-XX Class 1500 Full Port Design Description Material Specs. Body Carbon Steel 216 Gr. WCB Cover Carbon Steel 216 Gr. WCB Disc Facing Stainless Steel 182 Gr. F6a/CR13 or Stellite/HF Hinge Carbon Steel 216 Gr WCB Hinge Pin Stainless Steel 182 Gr. F6a/CR13 Seat Ring Stainless Steel 182 Gr. F6a/CR13, Stellite/HF Plug Carbon Steel 108 Gr.1045 Cover Bolt Carbon Steel 193 Gr. B7/B7M Cover Nut Carbon Steel 194 Gr. 2H/2HM Disc Nut Carbon Steel 563 Gr. B Washer Stainless Steel 276 Type 304 Eye Bolt Carbon Steel 307 Gr. B Name Plate Stainless Steel 304/L Gasket Soft Metal Ring CD Plated B Standards Face to Face/End to End NSI B16.10 Flange Dimensions NSI B16.5 Basic Design* PI 600 Testing PI 598 *10 and over sizes are according to NSI B16.34 ll sizes meet the design requirements for NSI B16.34 Size (in) Face to Face RF/BW Face to Face RTJ Short Pattern End to End BW B. Height Weight (Kg) Short Pattern BW Weight (Kg) Long Pattern BW Weight (Kg) Long Pattern RF Size (in) 20. Face to Face RF/BW Face to Face RTJ Short Pattern End to End BW - B. Height 2600 Weight (Kg) Short Pattern RF 4809 (BW) PGE 41

39 CONSIDERTIONS OF TECHNICL RISK / LIMIT OF LIBILITY FOR PV GTE, GLOBE, CHECK VLVES ustralian Pipeline Valve don t consider in our design the following factors of risk: 1. ustralian Pipeline Valve Standard valves can be used in a temperature range between -29 to +490 C. (Note, pressure limitations apply above 38 C refer to Pressure/Temperature charts.) For service temperatures below -29 C valves construction materials shall be submitted to an impact test at the minimum service temperature. For temperatures above and below the standard range, special seals need to be specified by the client. 2. The onus is on the customer to specify all materials of construction and service conditions. ustralian Pipeline Valve shall assume standard materials and conditions if not otherwise specified. 3. ustralian Pipeline Valve Standard valves are not equipped with devices suitable to avoid internal over-pressures caused by incorrect operations of process or by-fluids & liquids subjected to an increase of volume and/or pressure (these devices, such as the over-pressure hole in the gate or safety seats are available upon request). 4. ustralian Pipeline Valve Standard valves are not designed with special devices to withstand a sudden thermal jump (thermal shock). 5. In general ustralian Pipeline Valve Standard valves are not mechanically designed to bear overloads due to exceptional atmospheric or natural phenomenon s (such as earthquakes). 6. In general ustralian Pipeline Valve Standard valves are not designed to bear loads on flanges, on pipe connections or pipe-line. 7. In general ustralian Pipeline Valve Standard valves can t withstand ice inside their bodies (in this case the user has to consider the optional stem extension for insulating, avoiding the presence of residual product inside the valve). 8. ustralian Pipeline Valve Standard valves are not suitable for low temperature service below -29 C (-20 F) unless supplied (in a suitable body material) with cryogenic stem extension and other modifications, (available on request). 9. ustralian Pipeline Valve Standard valves are suitable for industrial oxygen (not medical) service when supplied degreased and packed in polyethylene bags only. 10. The compatibility between the valves construction materials and medium is selected by the user. The user is ultimately responsible for verifying the compatibility between medium and materials. 11. brasive or dirty service applications need to be considered and stated at time of order. VLVE STRT-UP Before installing the valve onto the pipe-line it is mandatory, for the user, to verify the compatibility of the valve with service conditions (medium, temperature and pressure). With reference to standard valves held in stock, the reseller and end user will have to assure themselves of the compatibility between the valve and the conditions required by the customer. ustralian Pipeline Valve gate valves must be only used for on-off (fully open/fully closed) service. Before using the valve in a potential explosive atmosphere it s necessary for the customer to: - To verify the correct type of valve and operator is specified. To verify the compatibility between the valve and the zone in which the valve should be installed To foresee the pipe-line ground condition on which the valve should be installed To check that the temperature if the valve surface is not higher than the flammable point of the atmosphere in which the valve is installed (in this case specify an insulating cover device for the valve and an extension for the operator) To avoid mechanical knocks during the installation that may cause sparks. ustralian Pipeline Valve cannot be held responsible for damage caused by use of the product for any reason, especially if it is improper use or modified. PGE 68

40 Notes

41 Notes

42 Notes

43 USTRLIN PIPELINE VLVE BRND RNGE - CTLOGUES COMPLETE PRODUCT LINE ustralian Pipeline Valve produces isolation, control and flow reversal protection products for severe and critical service media in utility, steam, pipelines, oil & gas and process industries. PV valves and pipeline products form the most competitive portfolio in the market. Product Brochure Oilfield Products Valves & Wellheads Ball Valves Floating & Trunnion Mounted Gate, Globe & Check Valves - Cast Ball Valves Floating Small Bore Gate, Globe & Check Valves - Forged Steel PV FMILY OF BRNDS RNGE - CTLOGUES Ball Valves Special Service Plug Valves Lubricated, Sleeved & Lined Diamond Gear Gearboxes Flowturn Ball Valves Multiway & Deadman Flowturn Gate, Globe & Check Valves Flowturn Instrument Valves Flowturn Strainers & Sight Glasses Steamco Steam Valves Supercheck Wafer Check Valves Superseal Butterfly Valves Superseal Industrial Ball Valves Torqturn ctuators TwinLok Tube Fittings Uniflo Check Valves Contact us for your local stockist/distributor View our catalogues at

44 QULITY SSURNCE ND CERTIFICTION 09/15