PACIFIC VALVES. Pressure Seal Valves
|
|
- Kellie Jennings
- 5 years ago
- Views:
Transcription
1 PCIFIC VLVES Pressure Seal Valves
2
3 PCIFIC VLVES PRESSURE SEL By Subject Product Overview Parallel Disc Gate Valve Features...5 Wedge Gate Valve Features...6 aterials of Construction, Gate Valves...7 Gate Valve Product Line Globe Valve Features...12 aterials of Construction, Globe Valves...13 Globe Valve Product Line aterials of Construction, Lift-Check Valves...17 Lift-Check Valve Product Line Y-Globe Valve Features...21 aterials of Construction, Y-Globe Valves...22 Y-Globe Stop and Stop-Check Valve Product Line aterials of Construction, Y-Globe Lift-Check Valves...27 Y-Globe Lift-Check Valve Product Line Tilting Disc Check Valve Features...32 aterials of Construction, Tilting Disc Check Valves...33 Tilting Disc Check Valve Product Line Figure Number System...37
4 Product Overview Selection TYPE ND SIZE Select the best type of valve for the intended service (gate, globe, or check). Gate and globe valves are available with a selection of wedge or disc and body configurations for different services. Valves may be sized to match existing lines, but they should also be sized according to flow conditions for maximum service life. RTINGS Valves must only be used in design conditions within the appropriate SE pressure-temperature ratings for valve class rating and body/bonnet material (see Technical Data section). TEPERTURE LIITTIONS Only use valves within the temperature limitations of their construction. Temperature limitations of body/bonnet materials, trim, bolting and packing and gaskets must all be considered. Special construction for extended service temperatures are available on application. TERIL ND SERVICE Pressure Seal valves are available in a variety of body/bonnet materials and trims. Specified materials should be compatible with the service. GTE VLVES 1. Gate valves are normally used for on-off service. They are not recommended for throttling service. 2. Gate valves are normally installed in horizontal pipe runs with the valve stem vertically up. They can also be installed in vertical or horizontal pipe runs with the valve stem other than vertical, but special construction may be required depending on valve size, service conditions and material. When purchasing valves for other than the normal installation, valve orientation should be specified when consulting the factory. 3. fter closing a gate valve with sufficient force to develop shutoff, the stem should be backed off slightly ( 1 8 to 1 4 turn) to relieve stem load. This will enable the stem to expand slightly without bending or damaging the valve and will not affect valve shutoff. 4. Gate valves are offered in two designs: Parallel Disc and Flexible Wedge. Parallel Disc are position seated; Flexible Wedge are torque seated when closing. Parallel Disc Gate Valve Wedge Gate Valve Walnut venue Signal Hill, C 90755
5 Product Overview GLOBE ND NON-RETURN (STOP-CHEC) VLVES 1. Globe valves are normally installed with flow and pressure under the disc. lways consult with the factory before installing valves with flow in the other direction. Under certain service conditions or when valves are equipped with cylinders or electric motor actuators, there may be a cost advantage in designing and installing the valves with flow over the disc. If actuators are sized for these conditions, care must be taken to assure valves are installed correctly. 2. Globe valves are suitable for most throttling applications; however, they should not be used for throttling at less than 10-20% open. This can cause excessive vibration, noise and damage to disc and seats. Use of smaller valves with lower flow capacity may permit the valve to be open a greater percentage, thus avoiding damage. Continuous severe throttling applications may require a control valve. 3. Non-return (Stop-Check) valves provide the same function as a globe valve with the addition of providing piston-lift-check valve protection in the event of backflow. The valve stem is not connected to the disc, and when the stem is in the open position then the disc is free to respond to the flow. Y-Pattern Globe and Non-Return (Stop-Check) Valve T-Pattern Globe and Non-Return (Stop-Check) Valve 3201 Walnut venue Signal Hill, C
6 Product Overview CHEC VLVES 1. Check valves are suited for moderately high velocity applications. For optimum performance, however, these valves should operate within a flow range sufficient to hold the valve open fully, but not so high that it produces excessive turbulence and pressure drop. Either extreme may damage valve internals, and shorten operating life. 2. Service involving frequent flow reversals or fluid pulsations should be avoided. Locating check valves no closer than five pipe diameters from elbows and other flow diverting means can minimize or eliminate problems in most installations. Where this is not possible, it may be necessary to reduce the maximum velocity by as much as 50%. 3. Excessive fluid noise is usually an indication that cavitation is occurring. 4. Check valves are normally designed for installation in horizontal pipe runs or in vertical lines where flow is up only. When valves are used in vertical pipe runs, this should be clearly specified. 5. If severe conditions are outside these recommendations contact Pacific Valves for further information prior to use. T-Pattern Lift-Check Valve Tilting Disc Check Valve Y-Pattern Lift-Check Valve Swing Check Valve PCIFIC VLVES CODES ND STNDRDS Years of research and development, together with practical experience in reconditioning all types of valves, have gone into the design and manufacture of Pacific valves. High quality material and workmanship, combined with the modern manufacturing methods used in producing these valves, is your assurance of a dependable, uniform product. Pacific valves are designed in accordance with applicable requirements of the latest edition of the following standards. PI merican Petroleum Institute SS anufacturers' Standardization Society of the Valve and Fittings Industry SE merican Society of echanical Engineers Walnut venue Signal Hill, C 90755
7 Parallel Disc Gate Valve Features Yoke Sleeve aluminum-bronze yokesleeve has needle type thrust bearings to minimize operating torque. ctuators valves can be supplied with any type of electric, hydraulic or pneumatic actuator. Standard manual handwheels on valves 12" and smaller with 14"and larger bevel gear operated. Stem Threaded to carrier Pinned and tack welded Provides stability Yoke fully fabricated yoke is seismically qualified while offering easy maintenance and actuator mounting. Gland two piece, self-aligning gland eliminates cocking. Pressure Seal uncomplicated design has segmented retaining ring and mild steel silver plated gasket to aid disassembly and provide maximum bonnet seal. Integral Backseat hardfaced for maximum life. Seat Ring welded-in seat rings are perpendicular to the flow bore for easy maintenance. Discs Spring loaded discs are self-aligning and reduce actuator torque requirements. Integral Stop Integrally cast carrier stop positions carrier disc assembly for reliable seating. Parallel Seat Gate Valve Parallel seat gate and seat ring construction can be furnished for high differential pressure services or where high piping loads or thermal expansion may cause sticking of a wedge type gate. The parallel seat gate assembly consists of two interchangeable spring loaded discs, a fully guided disc carrier, and retaining pins. Position seating eliminates stress and potential binding due to thermal expansion of the stem. Spring loaded discs help affect a tight seal in low differential pressure services. Discs are interchangeable which simplifies in-line maintenance and eliminates the need to custom fit the seats to the discs. Internal stops provide positive over travel protection for power actuated valves and act as a reference to position the discs in the open and closed positions. This design features low seating torque which reduces actuator size and cost. Hardfaced seating surfaces provide high cycle capability in very high differential pressure services. Features Self aligning interchangeable discs No wedging force; disc reacts freely to thermal changes Uniform seat wear Positive disc travel stops cast into body Lower torque may allow smaller actuator Ease of maintenance Position seated for closure 3201 Walnut venue Signal Hill, C
8 Wedge Gate Valve Features Yoke Sleeve aluminum-bronze yoke sleeve has needle type thrust bearings to minimize operating torque. ctuators valves can be supplied with any type of electric, hydraulic or pneumatic actuator. Standard manual handwheels on valves 12" and smaller with 14" and larger bevel gear operated. Stem all Pacific wedged gate valves are provided with T-head stems. This design allows the wedge to self-align, eliminating the possibility of a bent stem jamming the wedge. Yoke fully fabricated yoke is seismically qualified while offering easy maintenance and actuator mounting. See Detail Gland two piece, self-aligning gland eliminates cocking. Pressure Seal uncomplicated design has segmented retaining ring and mild steel silver plated gasket to aid disassembly and provide maximum bonnet seal. Integral Backseat hardfaced for maximum life. Seat Ring hardfaced seat rings are welded to body. Tapered design provides unobstructed flow path. Body streamlined flow path minimizes pressure drop. End-to-end dimensions meet SE B ost sizes can be furnished with PI 600 wall thickness. Wedge one-piece, flexible wedge is fully guided, resists sticking or binding due to thermal expansion, has hardfaced seating surfaces for long life. Parallel seat or solid wedge also available. Flexible wedge The flex wedge is a one piece, fully guided cast wedge with a central hub to allow the seating faces to move relative to each other thus compensating for distortion of the body seats due to thermal expansion or piping loads. Seat ring and wedge seating surfaces are set on a 5 degree angle from vertical to minimize sliding contact of the wedge and seat ring during opening and closing. Wedging actions help affect a tight seal in low differential pressure services. Flexible wedge construction resists wedge sticking or binding in services where the valve may be closed when hot and opened when cold. Seating surfaces are hardfaced to provide high cycle capability in very high differential pressure services. Detail *Where applicable Segment Ring Thrust Ring* Gasket Body Bonnet Walnut venue Signal Hill, C 90755
9 aterials of Construction: Gate Valve b, a NO PRT NE CRBON STEEL CHROE CHROE 9Cr-1o-V 316 STINLESS 50 HNDWHEEL ST 47 GR ST 47 GR ST 47 GR ST 47 GR ST 47 GR YOE SLEEVE ST 148 LLOY 955 ST 148 LLOY 955 ST 148 LLOY 955 ST 148 LLOY 955 ST 148 LLOY BERINGS FG STD FG STD FG STD FG STD FG STD 52 GLND STUD CRBON STEEL CRBON STEEL CRBON STEEL CRBON STEEL CRBON STEEL 16a NUTS ST 194 GR 2H ST 194 GR 2H ST 194 GR 2H ST 194 GR 2H ST 194 GR 2H 36 GLND FLNGE CRBON STEEL CRBON STEEL CRBON STEEL CRBON STEEL CRBON STEEL 35 GLND 300 SERIES SST 300 SERIES SST 300 SERIES SST 300 SERIES SST 300 SERIES SST 46 PCING GRPHITIC* GRPHITIC** GRPHITIC** GRPHITIC** GRPHITIC** 124 SEGENT RING ISI 4140 OR 4340 ISI 4140 OR 4340 ISI 4140 OR 4340 ISI 4140 OR 4340 ISI 4140 OR THRUST RlNG 4 ISI 4340 OR 4140 ISI 4340 OR 4140 ISI 4340 OR 4140 ISI 4340 OR 4140 ISI 4340 OR GSET ILD STEEL ILD STEEL ILD STEEL ILD STEEL ST 182 GR F316L SILVER PLTED SILVER PLTED SILVER PLTED SILVER PLTED CHROE PLTED 30 BONNET CRBON STEEL ST 182 GR F22 ST 182 GR F22 ST 182 GR F91 ST 182 GR F316 W/CO-CR W/CO-CR W/CO-CR W/CO-CR W/CO-CR 70 STE 13% CHROE 13% CHROE 13% CHROE 13% CHROE ST 705 GR BODY 1 ST 216 GR WCB/WCC 3 ST 217 GR WC6 ST 217 GR WC9 ST 217 GR C12 ST 351 GR CF8 71 WEDGE DISC CRBON STEEL 316 / 316L OR CR 316L SS OR CR 316L SS ST 351 GR CF8 W/CO-CR OVERLY W/CO-CR OVERLY W/CO-CR OVERLY W/CO-CR OVERLY W/CO-CR OVERLY 11 SET RINGS CRBON STEEL 316 / 316L OR CR 316L SS OR CR LLOY 91/CO-CR 316L SS W/CO-CR OVERLY W/CO-CR OVERLY W/CO-CR OVERLY W/CO-CR OVERLY 98 BONNET STUDS ST 193 GR B7 ST 193 GR B7 ST 193 GR B7 ST 193 GR B7 ST 193 GR B7 16b STUD NUTS ST 194 GR 2H ST 194 GR 2H ST 194 GR 2H ST 194 GR 2H ST 194 GR 2H 25 CRRIER 2 CRBON STEEL F11 F22 SST 316 SS 26 PIN 2 12% CR 12% CR 12% CR 12% CR 17-4 PH 27 SPRING 2 INCONEL INCONEL INCONEL INCONEL INCONEL 56 J NUT CRBON STEEL CRBON STEEL CRBON STEEL CRBON STEEL CRBON STEEL 30 PIN 2 12% CR 12% CR 12% CR 12% CR 17-4 PH 16c NUTS ST 194 GR 2H ST 194 GR 2H ST 194 GR 2H ST 194 GR 2H ST 194 GR 2H 59 GRESE FITTING FG. STD. FG. STD. FG. STD. FG. STD. FG. STD. 98 THREDED COL. ST 193 GR B7 ST 193 GR B7 ST 193 GR B7 ST 193 GR B7 ST 193 GR B7 98a BOLTING ST 193 GR B7 ST 193 GR B7 ST 193 GR B7 ST 193 GR B7 ST 193 GR B7 98b DRW BOLTING ST 193 GR B7 ST 193 GR B7 ST 193 GR B7 ST 193 GR B7 ST 193 GR B7 54 HNDWHEEL NUT CRBON STEEL CRBON STEEL CRBON STEEL CRBON STEEL CRBON STEEL 128 TUBULR COL. CRBON STEEL CRBON STEEL CRBON STEEL CRBON STEEL CRBON STEEL Pacific Valves reserves the right to change or modify product design or construction without prior notice and without incurring any obligation to make such changes and modifications on products previously or subsequently sold. NOTES: SS inlay is standard in the gasket area of the body on SE class 2500 valves. For this option on other pressure classes, specify special features suffix H. 2. Parallel Disc only. 3. WCC valve bonnets and internals will be manufactured with 300 series SS and/or CR 4. Thrust ring comes standard on 12" and larger SE class 1500 and all sizes of SE class *Special high temperature packing is recommended for services over 850 F. Consult factory when ordering. **High temperature packing is standard Walnut venue Signal Hill, C
10 Gate Valve SE Class 600 Fig. No WE* Flex Wedge, Butt Fig. No Flex Wedge, Flanged Raised Face Fig. No RJ Flex Wedge, Flanged, Ring Joint Fig. No WE* Fig. No Fig. No RJ Parallel Seat Disc, Butt Parallel Seat Disc, Flanged, Raised Face Parallel Seat Disc, Flanged, Ring Joint Dim Description in mm * RTJ Open VLVE SIZES (inches) in. N/ N/ mm N/ N/ in. N/ N/ mm N/ N/ in mm in mm lbs kg lbs kg NOTE: 1. Valves are supplied with a handwheel actuator on all sizes. VENTURI GTE VLVES Fig. No WE* Butt VLVE SIZES (inches) Dim Description 8x6x8 10x8x10 12x10x12 14x12x14 20x18x20 24x20x24 26x24x26 Open in mm in mm in mm lbs kg NOTES: 1. Valves are supplied with a handwheel actuator on all sizes. 1. Dimensions, weights and other engineering data are subject to change or modification. This data is not to be used for construction unless confirmed by Pacific Valves. 2. ll pressure seal gate valves are available with a solid wedge. Specify figure number Related data available in Technical Data, ctuators and ccessories sections Walnut venue Signal Hill, C 90755
11 Gate Valve SE Class 900 Fig. No WE* Flex Wedge, Butt Fig. No Flex Wedge, Flanged Raised Face Fig. No RJ Flex Wedge, Flanged, Ring Joint Fig. No WE* Fig. No Fig. No RJ Parallel Seat Disc, Butt Parallel Seat Disc, Flanged, Raised Face Parallel Seat Disc, Flanged, Ring Joint VLVE SIZES (inches) Dim Description ** ** RTJ Open in mm in. N/ N/ mm N/ N/ in. N/ N/ mm N/ N/ in mm in mm lbs kg lbs N/ N/ kg N/ N/ NOTE: 1. Valves are supplied with a handwheel actuator through 14". Bevel gear supplied on 16"-24" VENTURI GTE VLVES Fig. No WE* Butt Dim Description 8x6x8 10x8x10 12x10x12 14x12x14 16x14x16 18x16x18 20x18x20 22x20x22 26x24x26 ** Open VLVE SIZES (inches) in mm in mm in mm lbs kg NOTES: 1. Valves are supplied with a handwheel actuator through 16" x 14" x 16". Bevel gear supplied on 18" x 16" x 18" and larger. 1. Dimensions, weights and other engineering data are subject to change or modification. This data is not to be used for construction unless confirmed by Pacific Valves. 2. ll pressure seal gate valves are available with a solid wedge. Specify figure number ** includes standard bevel gear where applicable (see note 1 above). 3. Related data available in Technical Data, ctuators and ccessories sections Walnut venue Signal Hill, C
12 Gate Valve SE Class 1500 Fig. No WE* Flex Wedge, Butt Fig. No Flex Wedge, Flanged Raised Face Fig. No RJ Flex Wedge, Flanged, Ring Joint Fig. No WE* Fig. No Fig. No RJ Parallel Seat Disc, Butt Parallel Seat Disc, Flanged, Raised Face Parallel Seat Disc, Flanged, Ring Joint VLVE SIZES (inches) Dim Description ** ** RTJ Open in mm in mm in mm in mm in mm lbs kg lbs kg NOTE: 1. Valves are supplied with a handwheel actuator through 12". Bevel gear supplied on 14"-24". VENTURI GTE VLVES Fig. No WE* Butt VLVE SIZES (inches) Dim Description 8x6x8 10x8x10 12x10x12 14x12x14 16x14x16 18x16x18 20x18x20 22x20x22 ** Open in mm in mm in mm lbs kg NOTES: 1. Valves are supplied with a handwheel actuator through 14" x 12" x 14". Bevel gear supplied on 16" x 14" x 16" and larger. 1. Dimensions, weights and other engineering data are subject to change or modification. This data is not to be used for construction unless confirmed by Pacific Valves. 2. ll pressure seal gate valves are available with a solid wedge. Specify figure number ** includes standard bevel gear where applicable (see note 1 above). 3. Related data available in Technical Data, ctuators and ccessories sections Walnut venue Signal Hill, C 90755
13 Gate Valve SE Class 2500 Fig. No H-7-WE* Flex Wedge, Butt Fig. No H-7 Flex Wedge, Flanged Raised Face Fig. No H-7-RJ Flex Wedge, Flanged, Ring Joint Fig. No H-7-WE* Parallel Seat Disc, Butt Fig. No H-7 Parallel Seat Disc, Flanged, Raised Face Fig. No H-7-RJ Parallel Seat Disc, Flanged, Ring Joint VLVE SIZES (inches) Dim Description ** ** RTJ Open in mm in (2) (2) (2) (2) (2) mm (2) (2) (2) (2) (2) in (2) (2) (2) (2) (2) mm (2) (2) (2) (2) (2) in mm in mm lbs kg lbs (2) (2) (2) (2) (2) kg (2) (2) (2) (2) (2) NOTES: 1. Valves are supplied with a handwheel actuator on sizes 2 1 2" - 10". Bevel gear supplied on 12" - 24". 2. For flanged end data on 14" - 24" contact Pacific Valves. VENTURI GTE VLVES VLVE SIZES (inches) Dim Description 8x6x8 10x8x10 12x10x12 14x12x14 16x14x16 18x16x18 20x18x20 ** Open Fig. No H-7-WE* Butt in mm in mm in mm lbs kg NOTES: 1. Valves are supplied with a handwheel actuator through 12". Bevel gear supplied on 14" x 12" x 24" and larger Dimensions, weights and other engineering data are subject to change or modification. This data is not to be used for construction unless confirmed by Pacific Valves. 2. ll pressure seal gate valves are available with a solid wedge. Specify figure number ** includes standard bevel gear where applicable (see note 1 above). 3. Related data available in Technical Data, ctuators and ccessories sections Walnut venue Signal Hill, C
14 Globe Valve Features Yoke Sleeve aluminum-bronze yoke sleeve minimizes operating torque. Larger sizes have needle bearing type thrust bearings. Stem precision-ground stem has upset tee-head for reliable stem/wedge connection. ctuators valves can be supplied with any type of electric, hydraulic or pneumatic actuator. Standard manual actuators are handwheels through 14". Yoke fully fabricated yoke is seismically qualified while offering easy maintenance and actuator mounting. Detail Gland two piece, self-aligning gland eliminates cocking. Swing out bolting facilitates maintenance. Bolted Yoke yoke is bolted to body. Pressure Seal uncomplicated design has segmented retaining ring and mild steel silver plated gasket to aid disassembly and provide maximum bonnet seal. Integral Backseat hardfaced for maximum backseat life. Hardened Seating Surfaces both disc and body seating surfaces are hard faced for maximum service life. Disc fully body guided for perfect seating in high pressure services. Body streamlined flow path minimizes pressure drop. Butt weld, venturi or flanged ends provide piping alternatives. Segment Ring Thrust Ring* Gasket Body Bonnet Detail *Where applicable Walnut venue Signal Hill, C 90755
15 aterials of Construction: Globe Stop and Stop-Check Valves a 35 98, 16b NO PRT NE CRBON STEEL CHROE CHROE 9 Cr-1o-V 316 STINLESS 50 HNDWHEEL ST 47 GR ST 47 GR ST 47 GR ST 47 GR ST 47 GR YOE SLEEVE ST 148 LLOY 955 ST 148 LLOY 955 ST 148 LLOY 955 ST 148 LLOY 955 ST 148 LLOY BERINGS FG STD FG STD FG STD FG STD FG STD 70 STE 13% CHROE 13% CHROE 13% CHROE 13% CHROE ST 705 GR GLND FLNGE CRBON STEEL CRBON STEEL CRBON STEEL CRBON STEEL CRBON STEEL 35 GLND 300 SERIES SST 300 SERIES SST 300 SERIES SST 300 SERIES SST 300 SERIES SST 46 PCING GRPHITIC* GRPHITIC** GRPHITIC** GRPHlTlC** GRPHITIC** 30 BONNET CRBON STEEL ST 182 GR, F22 ST 182 GR, F22 ST 182 GR, F91 ST 182 GR, F316 W/CO-CR W/CO-CR W/CO-CR W/CO-CR W/CO-CR 124 SEGENT RING ISI 4340 OR 4140 ISI 4340 OR 4140 ISI 4340 OR 4140 ISI 4340 OR 4140 ISI 4340 OR THRUST RING 3 ISI 4340 OR 4140 ISI 4340 OR 4140 ISI 4340 OR 4140 ISI 4340 OR 4140 ISI 4340 OR GSET ILD STEEL ILD STEEL ILD STEEL ILD STEEL ST 182 GR F316L SILVER PLTED SILVER PLTED SILVER PLTED SILVER PLTED CHROE PLTED 72 DISC NUT CRBON STEEL 316 SS OR CR 316 SS OR CR 316 SS 316L SS 71 DISC CRBON STEEL 316 SS OR CR 316 SS OR CR 316 SS 316L SS W/CO-CR OVERLY W/CO-CR OVERLY W/CO-CR OVERLY W/CO-CR OVERLY W/CO-CR OVERLY 11 SET RING CRBON STEEL W/CO-CR 316 SS OR CR W/CO-CR 316 SS OR CR W/CO-CR LLOY 91/CO-CR 316L SS 10 BODY 1 ST 216 GR WCB OR WCC 2 ST 217 GR WC6 ST 217 GR WC9 ST 217 GR C12- ST 351 GR CF8 98 BONNET STUDS ST 193 GR B7 ST 193 GR B7 ST 193 GR B7 ST 193 GR B7 ST 193 GR B7 16b STUD NUTS ST 194 GR 2H ST 194 GR 2H ST 194 GR 2H ST 194 GR 2H ST 194 GR 2H 52 GLND STUD CRBON STEEL CRBON STEEL CRBON STEEL CRBON STEEL CRBON STEEL 16a GLND NUTS ST 194 GR 2H ST 194 GR 2H ST 194 GR 2H ST 194 GR 2H ST 194 GR 2H 113 DISC THRUST PLTE 316 SS/PLTED 316 SS/PLTED 316 SS/PLTED 316 SS/PLTED 316 SS/PLTED16c 16c NUTS ST 194 GR 2H ST 194 GR 2H ST 194 GR 2H ST 194 GR 2H ST 194 GR 2H 59 GRESE FITTING FG STD. FG STD. FG STD. FG STD. FGSTD 98 THREDED COL. ST 193 GR B7 ST 193 GR B7 ST 193 GR B7 ST 193 GR B7 ST 193 GR B7 98a BOLTING ST 193 GR B7 ST 193 GR B7 ST 193 GR B7 ST 193 GR B7 ST 193 GR B7 98b DRW BOLTING ST 193 GR B7 ST 193 GR B7 ST 193 GR B7 ST 193 GR B7 ST 193 GR B7 54 HNDWHEEL NUT CRBON STEEL CRBON STEEL CRBON STEEL CRBON STEEL CRBON STEEL 128 TUBULR COL. CRBON STEEL CRBON STEEL CRBON STEEL CRBON STEEL CRBON STEEL 56 J NUT CRBON STEEL CRBON STEEL CRBON STEEL CRBON STEEL CRBON STEEL Pacific Valves reserves the right to change or modify product design or construction without prior notice and without incurring any obligation to make such changes and modifications on products previously or subsequently sold. NOTES: SS inlay is standardly furnished in the gasket area of the body on SE class 2500 valves. For this option on other pressure classes, specify special features suffix H. 2. WCC valve bonnet and internals will be manufactured with 300 series stainless or CR material. 3. Thrust ring comes standard on 12" and larger SE class ll sizes of SE class *Special high temperature packing is recommended for services over 850 F. Consult factory when ordering. **High temperature packing is standard Walnut venue Signal Hill, C
16 Globe Stop and Stop-Check Valve SE Class 900 Globe Stop Valves Fig. No WE* Butt Fig. No Flanged, Raised Face Fig. No RJ Flanged, Ring Joint Globe Stop-Check Valves Fig. No WE* Butt Fig. No Flanged, Raised Face Fig. No RJ Flanged, Ring Joint Dim Description ** ** RTJ Open VLVE SIZES (inches) in mm in. N/ N/ mm N/ N/ in. N/ N/ mm N/ N/ in mm in mm lbs kg lbs N/ N/ kg N/ N/ NOTE: 1. Integral body seat on 2" through 4" size. VENTURI Globe STOP and STOP-CHEC VLVES Globe Stop Valves Fig. No WE* Butt Globe Stop-Check Valves Fig No WE* Butt VLVE SIZES (inches) Dim Description 8x6x8 10x8x10 12x10x12 14x12x14 16x14x16 ** Open in mm in mm in mm lbs kg Dimensions, weights and other engineering data are subject to change or modification. This data is not to be used for construction unless confirmed by Pacific Valves. 2. For best performance, size for full open operation. See Flow Calculations in the Technical Data Section. ** includes standard bevel gear where applicable. 3. Related data available in Technical Data, ctuators and ccessories sections Walnut venue Signal Hill, C 90755
17 Globe Stop and Stop-Check Valve SE Class 1500 Globe Stop Valves Fig. No WE* Butt Fig. No Flanged, Raised Face Fig. No RJ Flanged, Ring Joint Globe Stop-Check Valves Fig. No WE* Butt Fig. No Flanged, Raised Face Fig. No RJ Flanged, Ring Joint Dim Description ** ** RTJ Open VLVE SIZES (inches) in mm in mm in mm in mm in mm lbs kg lbs kg NOTE: 1. Integral body seat on 2" through 4" size. VENTURI Globe STOP and STOP-CHEC VLVES Globe Stop Valves Fig. No WE* Butt Globe Stop-Check Valves Fig No WE* Butt VLVE SIZES (inches) Dim Description 8x6x8 10x8x10 12x10x12 14x12x14 ** Open in mm in mm in mm lbs kg Dimensions, weights and other engineering data are subject to change or modification. This data is not to be used for construction unless confirmed by Pacific Valves. 2. For best performance, size for full open operation. See Flow Calculations in the Technical Data Section. ** includes standard bevel gear where applicable. 3. Related data available in Technical Data, ctuators and ccessories sections Walnut venue Signal Hill, C
18 Globe Stop and Stop-Check Valve SE Class 2500 Globe Stop Valves Fig. No H-7-WE* Fig. No H-7 Fig. No H-7-RJ Butt Flanged, Raised Face Flanged, Ring Joint Globe Stop-Check Valves Fig. No H-7-WE* Butt Fig. No H-7 Flanged Raised Face Fig. No H-7-RJ Flanged, Ring Joint 1 2 ** ** RTJ Open VLVE SIZES (inches) Dim Description in mm in mm in mm in mm in mm lbs kg lbs kg NOTE: 1. Integral body seat on 2" through 3" size. VENTURI Globe STOP and STOP-CHEC VLVES Globe Stop Valves Fig. No H-7-WE* Butt Globe Stop-Check Valves Fig No H-7-WE* Butt VLVE SIZES (inches) Dim Description 8x6x8 10x8x10 12x10x12 14x12x14 ** Open NOTES: 1. Impact standard all sizes. in mm in mm in mm lbs kg Dimensions, weights and other engineering data are subject to change or modification. This data is not to be used for construction unless confirmed by Pacific Valves. 2. For best performance, size for full open operation. See Flow Calculations in the Technical Data Section. ** includes standard bevel gear where applicable. 3. Related data available in Technical Data, ctuators and ccessories sections Walnut venue Signal Hill, C 90755
19 aterials of Construction: Lift-Check Valve 16B NO PRT NE CRBON STEEL CHROE CHROE 9 Cr-1o-V 316 STINLESS 98 BONNET STUDS ST 193 GR B7 ST 193 GR B7 ST 193 GR B7 ST 193 GR B7 ST 193 GR B7 16b STUD NUTS ST 194 GR 2H ST 194 GR 2H ST 194 GR 2H ST 194 GR 2H ST 194 GR 2H 43 BONNET CRRIER CRBON STEEL CRBON STEEL CRBON STEEL CRBON STEEL CRBON STEEL 124 SEGENT RING ISI 4340 OR 4140 ISI 4340 OR 4140 ISI 4340 OR 4140 ISI 4340 OR 4140 ISI 4340 OR THRUST RING 3 ISI 4340 OR 4140 ISI 4340 OR 4140 ISI 4340 OR 4140 ISI 4340 OR 4140 ISI 4340 OR GSET ILD STEEL ILD STEEL ILD STEEL ILD STEEL ST 182 GR F316L SILVER PLTED SILVER PLTED SILVER PLTED SILVER PLTED CHROE PLTED 30 BONNET CP CRBON STEEL ST 182 GR F22 ST 182 GR F22 ST 182 GR F91 ST 182 GR F DISC CRBON STEEL 316 SS OR CR 316 SS OR CR 316 SS 316L W/CO-CR OVERLY W/CO-CR OVERLY W/CO-CR OVERLY W/CO-CR OVERLY W/CO-CR OVERLY 10 BODY 1 ST 216 GR WCB or WCC 2 ST 217 GR WC6 ST 217 GR WC9 ST 217 GR C12 ST 351 GR CF8 11 SET RING CRBON STEEL 316 SS OR CR 316 SS OR CR LLOY 91/CO-CR 316L SS W/CO-CR OVERLY W/CO-CR OVERLY W/CO-CR OVERLY W/CO-CR OVERLY Pacific Valves reserves the right to change or modify product design or construction without prior notice and without incurring any obligation to make such changes and modifications on products previously or subsequently sold. NOTES: SS inlay is standardly furnished in the gasket area of the body on SE class 2500 valves. For this option on other pressure classes, specify special features suffix H. 2. WCC valve bonnet and internals will be manufactured with 300 series stainless or CR material. 3. Thrust ring comes standard on 12" and larger SE class 1500 and all sizes of SE class Walnut venue Signal Hill, C
20 Lift-Check Valve SE Class 900 Fig. No WE* Butt Fig. No Flanged, Raised Face Fig. No RJ Flanged, Ring Joint 1 2 RTJ Open VLVE SIZES (inches) Dim Description NOTE: 1. Integral body seat on 2" through 4". in mm in. N/ N/ mm N/ N/ in. N/ N/ mm N/ N/ in mm lbs kg lbs N/ N/ kg N/ N/ VENTURI lift-check VLVES Fig. No WE* Butt VLVE SIZES (inches) Dim Description 8x6x8 10x8x10 12x10x12 14x12x14 16x14x16 Open in mm in mm lbs kg Dimensions, weights and other engineering data are subject to change or modification. This data is not to be used for construction unless confirmed by Pacific Valves. 2. For best performance, size for full open operation. See Flow Calculations in the Technical Data Section. 3. Related data available in Technical Data, ctuators and ccessories sections Walnut venue Signal Hill, C 90755
21 Lift-Check Valve SE Class 1500 Fig. No WE* Butt Fig. No Flanged, Raised Face Fig. No RJ Flanged, Ring Joint 1 2 VLVE SIZES (inches) Dim Description RTJ NOTE: 1. Integral body seat on 2" through 4" size. in mm in mm in mm in mm lbs kg lbs kg VENTURI lift-check VLVES Fig. No WE* Butt VLVE SIZES (inches) Dim Description 8x6x8 10x8x10 12x10x12 14x12x14 Open in mm in mm lbs kg Dimensions, weights and other engineering data are subject to change or modification. This data is not to be used for construction unless confirmed by Pacific Valves. 2. For best performance, size for full open operation. See Flow Calculations in the Technical Data Section. 3. Related data available in Technical Data, ctuators and ccessories sections Walnut venue Signal Hill, C
22 Lift-Check Valve SE Class 2500 Fig. No H-7-WE* Butt Fig. No H-7 Flanged, Raised Face Fig. No H-7-RJ Flanged, Ring Joint 1 2 RTJ NOTE: 1. Integral body seat on 2" through 3" size. VLVE SIZES (inches) Dim Description in mm in mm in mm in mm lbs kg lbs kg VENTURI lift-check VLVES Fig. No H-7-WE* Butt VLVE SIZES (inches) Dim Description 8x6x8 10x8x10 12x10x12 14x12x14 in mm in Open mm lbs kg Dimensions, weights and other engineering data are subject to change or modification. This data is not to be used for construction unless confirmed by Pacific Valves. 2. For best performance, size for full open operation. See Flow Calculations in the Technical Data Section. 3. Related data available in Technical Data, ctuators and ccessories sections Walnut venue Signal Hill, C 90755
23 Y-Globe Valve Features ctuation can be supplied with a hammerblow handwheel, manual gear set, electric motor operator, pneumatic or hydraulic cylinder operator. Stem stainless steel stem is precision ground for minimal packing friction during operation. Stem Guide acts as anti-rotating device for the stem. Backseat integral hardfaced bonnet backseat. Yoke designed to withstand seismic activities, the fully fabricated yoke features hassle free assembly/ disassembly of topworks and simple actuator mounting. Gland two piece self-aligning gland and gland flange eliminates cocking if packing adjustment is required. Detail Pressure Seal Design consists of a gasket, thrust ring and uncomplicated segmented retaining rings to ensure maximum bonnet seal. * Body streamlined flow path demonstrating high Cv factors which minimize pressure drop across a given system. Low Pressure Drop = Low Operating Cost Guiding System includes a two-piece disc assembly and hardfaced body guides. The disc assembly maintains contact with the guides through the full valve stroke. Seating Surface the disc and body seating surfaces are hardfaced for extended service. Detail Rotated 45 ccw Segment Ring Thrust Ring* Gasket Body Bonnet *Where applicable 3201 Walnut venue Signal Hill, C
24 aterials of Construction: Y-Globe Valve See Detail 98a 16a 16b c a Detail NO PRT NE CRBON STEEL CHROE CHROE 9Cr-1o-V 316 STINLESS 10 BODY ST 216 GR WCB OR ST 217 GR WC6 ST 217 GR WC9 ST 217 GR C12 ST 351 GR CF8 WCC 1 W/CO-CR W/CO-CR W/CO-CR W/CO-CR W/CO-CR 11 SET RINGS CRBON STEEL W/ 316 SS OR CR W/ 316 SS OR CR W/ LLOY 91/CO-CR 316L W/CO-CR CO-CR OVERLY CO-CR OVERLY CO-CR OVERLY OVERLY 16a NUT ST 194 GR 2H ST 194 GR 2H ST 194 GR 2H ST 194 GR 2H ST 194 GR 2H 16b NUT ST 194 GR 2H ST 194 GR 2H ST 194 GR 2H ST 194 GR 2H ST 194 GR 2H 16c NUT ST 194 GR 2H ST 194 GR 2H ST 194 GR 2H ST 194 GR 2H ST 194 GR 2H 19 SCREW 193 GR B7 193 GR B7 193 GR B7 193 GR B7 193 GR B7 21 JCING BOLTS 582 GR GR GR GR GR THRUST RING 2 ISI 4140 OR 4340 ISI 4140 OR 4340 ISI 4140 OR 4340 ISI 4140 OR 4340 ISI 4140 OR BONNET CRBON STEEL W/ ST 182 GR F22 W/ ST 182 GR F22 W/ ST 182 GR F91 W/ ST 182 GR F316 W/ CO-CR CO-CR CO-CR CO-CR CO-CR 35 GLND 300 SERIES SST 300 SERIES SST 300 SERIES SST 300 SERIES SST 300 SERIES SST 36 GLND FLNGE CRBON STEEL CRBON STEEL CRBON STEEL CRBON STEEL CRBON STEEL 43 LOWER PLTE CRBON STEEL CRBON STEEL CRBON STEEL CRBON STEEL CRBON STEEL 46 PCING GRPHITIC GRPHITIC GRPHITIC GRPHITIC GRPHITIC 48 RETINER 11-13% CHROE 11-13% CHROE 11-13% CHROE 11-13% CHROE 11-13% CHROE 48a RETINER 316 SS 316 SS 316 SS 316 SS 316 SS 55 GSET ILD STEEL WITH ILD STEEL WITH ILD STEEL WITH ILD STEEL WITH ST 182 GR F316L SILVER PLTE SILVER PLTE SILVER PLTE SILVER PLTE CHROE PLTED 62 EY ISI 01 ISI 01 ISI 01 ISI 01 ISI STE GUIDE CRBON STEEL CRBON STEEL CRBON STEEL CRBON STEEL CRBON STEEL 70 STE ST 582 GR 416 ST 582 GR 416 ST 582 GR 416 ST 582 GR 416 ST 705 GR DISC CRBON STEEL W/ 316 SS OR CR W/ 316 SS OR CR W/ 316 SS W/ 316L SS W/ CO-CR OVERLY CO-CR OVERLY CO-CR OVERLY CO-CR OVERLY CO-CR OVERLY 72 DISC NUT CRBON STEEL W/ 316 SS OR CR W/ 316 SS OR CR W/ 316 SS W/ 316L SS W/ CO-CR OVERLY CO-CR OVERLY CO-CR OVERLY CO-CR OVERLY CO-CR OVERLY 86 CRRIER CRBON STEEL CRBON STEEL CRBON STEEL CRBON STEEL CRBON STEEL 97 BOLT ST 193 GR B7 ST 193 GR B7 ST 193 GR B7 ST 193 GR B7 ST 193 GR B7 98 BOLT ST 193 GR B7 ST 193 GR B7 ST 193 GR B7 ST 193 GR B7 ST 193 GR B7 98a BOLT ST 193 GR B7 ST 193 GR B7 ST 193 GR B7 ST 193 GR B7 ST 193 GR B7 120 DPTER CRBON STEEL CRBON STEEL CRBON STEEL CRBON STEEL CRBON STEEL 124 SEGENT RING ISI 4140 OR 4340 ISI 4140 OR 4340 ISI 4140 OR 4340 ISI 4140 OR 4340 ISI 4140 OR COLUN CRBON STEEL CRBON STEEL CRBON STEEL CRBON STEEL CRBON STEEL 200 CTUTOR CONSULT FCTORY CONSULT FCTORY CONSULT FCTORY CONSULT FCTORY CONSULT FCTORY Pacific Valves reserves the right to change or modify product design or construction without prior notice and without incurring any obligation to make such changes and modifications on products previously or subsequently sold. NOTES: 1. WCC valve bonnets and internals will be manufactured with 300 series SS and/or 2¼ CR. 2. Thrust ring on all 12" and larger 1500 and all Walnut venue Signal Hill, C 90755
25 Y-Globe Stop and Stop-Check Valves SE Class 600 Y-Globe Stop Valves Fig. No WE* Butt Y-Globe Stop-Check Valves Fig. No WE* Butt VLVE SIZES (inches) Dim Description in mm in mm in mm lbs kg VENTURI Y-Globe STOP and STOP-CHEC VLVES Y-Globe Stop Valves Fig. No WE* Butt Y-Globe Stop-Check Valves Fig. No WE* Butt VLVE SIZES (inches) Dim Description 10x8x10 12x10x12 14x12x14 16x14x16 18x16x18 20x18x20 22x20x22 26x24x26 in mm in mm in mm lbs kg Dimensions, weights and other engineering data are subject to change or modification. This data is not to be used for construction unless confirmed by Pacific Valves. 2. For best performance, size for full open operation. See Flow Calculations in the Technical Data Section. 3. Related data available in Technical Data, ctuators and ccessories sections. 4. Valves supplied with hammerblow handwheel as a standard Walnut venue Signal Hill, C
26 Y-Globe Stop and Stop-Check Valves SE Class 900 Y-Globe Stop Valves Fig. No WE* Butt Y-Globe Stop-Check Valves Fig. No WE* Butt Dim Description VLVE SIZES (inches) in mm in mm in mm lbs kg VENTURI Y-Globe STOP and STOP-CHEC VLVES Y-Globe Stop Valves Fig. No WE* Butt Y-Globe Stop-Check Valves Fig. No WE* Butt VLVE SIZES (inches) Dim Description 8x6x8 10x8x10 12x10x12 14x12x14 16x14x16 18x16x18 20x18x20 22x20x22 26x24x26 in mm in mm in mm lbs kg Dimensions, weights and other engineering data are subject to change or modification. This data is not to be used for construction unless confirmed by Pacific Valves. 2. For best performance, size for full open operation. See Flow Calculations in the Technical Data Section. 3. Related data available in Technical Data, ctuators and ccessories sections. 4. Valves supplied with hammerblow handwheel as a standard Walnut venue Signal Hill, C 90755
27 Y-Globe Stop and Stop-Check Valves SE Class 1500 Y-Globe Stop Valves Fig. No WE* Butt Y-Globe Stop-Check Valves Fig. No WE* Butt Dim Description VLVE SIZES (inches) in mm in mm in mm lbs kg VENTURI Y-Globe STOP and STOP-CHEC VLVES Y-Globe Stop Valves Fig. No WE* Butt Y-Globe Stop-Check Valves Fig. No WE* Butt VLVE SIZES (inches) Dim Description 8x6x8 10x8x10 12x10x12 14x12x14 16x14x16 18x16x18 20x18x20 22x20x22 26x24x26 in mm in mm in mm lbs kg Dimensions, weights and other engineering data are subject to change or modification. This data is not to be used for construction unless confirmed by Pacific Valves. 2. For best performance, size for full open operation. See Flow Calculations in the Technical Data Section. 3. Related data available in Technical Data, ctuators and ccessories sections. 4. Valves supplied with hammerblow handwheel as a standard Walnut venue Signal Hill, C
28 Y-Globe Stop and Stop-Check Valves SE Class 2500 Y-Globe Stop Valves Fig. No H-7-WE* Butt Y-Globe Stop-Check Valves Fig. No H-7-WE* Butt Dim Description VLVE SIZES (inches) in mm in mm in mm lbs kg VENTURI Y-Globe STOP and STOP-CHEC VLVES Y-Globe Stop Valves Fig. No H-7-WE* Butt Y-Globe Stop-Check Valves Fig No H-7-WE* Butt VLVE SIZES (inches) Dim Description 8x6x8 10x8x10 12x10x12 14x12x14 16x14x16 18x16x18 20x18x20 22x20x22 26x24x26 in mm in mm in mm lbs kg Dimensions, weights and other engineering data are subject to change or modification. This data is not to be used for construction unless confirmed by Pacific Valves. 2. For best performance, size for full open operation. See Flow Calculations in the Technical Data Section. 3. Related data available in Technical Data, ctuators and ccessories sections. 4. Valves supplied with hammerblow handwheel as a standard Walnut venue Signal Hill, C 90755
Pressure Seal Valves PACIFIC VALVES
PCIFIC VLVES PCIFIC VLVES PRESSURE SEL By Subject Product Overview...4-6 Parallel Disc Gate Valve Features...7 Wedge Gate Valve Features...8 aterials of Construction, Gate Valves...9 Gate Valve Product
More informationBOLTED BONNET API 600
PACIFIC VALVES BOLTED BONNET API 600 By Subject Product Overview...2-4 Gate Valves Major Features...5 Gate Valves Optional Features...6 Materials of Construction: Gate Valves...7 Gate Valves Product Line...8-10
More informationBolted Bonnet Valves. (BL Series) Cast Steel. Cast Steel Bolted Bonnet Valves - BL Series
Cast Steel Bolted Bonnet Valves (BL Series) Gate Valve - BL5 Series Gate Valve Features Globe Valve - BL6 Series Globe Valve Features Swing Check Valve - BL7 Series Optional Features Model Numbers GATE
More informationFasani Pressure Seal Cast Gate Valves - Style A Wedge Gate and Parallel Slide
A series of robust gate valves specifically designed for applications in the power industry Features General application Our pressure seal -Style A gate valves are recommended for several applications
More informationHANCOCK GATE, GLOBE AND CHECK VALVES CAST STEEL
ANCOCK GATE, GOBE AND CECK VAVES CAST STEE A range of ASME Class 150, 300 and 600 bolted bonnet cast steel valves, with metal-to-metal seating in flanged or butt weld ends FEATURES Gate valves Internal
More informationFASANI PRESSURE SEAL CAST GLOBE VALVES - STYLE B Y AND T PATTERN
A wide range of globe valves specifically designed for high pressure and high temperature applications, where low pressure loss is required. FEATURES GENERAL APPLICATION Our pressure seal globe valves
More informationHANCOCK 600 GATE, GLOBE AND CHECK VALVES CAST STEEL
ANCOCK 600 GATE, GOBE AND CECK VAVES CAST STEE A range of ASME Class 150, 300 and 600 bolted bonnet cast steel valves, with metal-to-metal seating in flanged or butt weld ends FEATURES Gate valves Internal
More informationSeries Direct contact and metal-to-metal seating makes the T-pattern globe stop valve ideal for most shut-off applications.
7 YARWAY Hancock T-Pattern Globe valves Direct contact and metal-to-metal seating makes the T-pattern globe stop valve ideal for most shut-off applications Features Heavy integral stellite hardfacing on
More informationGATE, GLOBE & CHECK VALVES - CAST STEEL SHORT VERSION
GTE, GLOBE & CHECK VLVES - CST STEEL SHORT VERSION QULITY VLVE MNUFCTURER USTRLIN PIPELINE VLVE Contents Figure Number System Material Combinations/Features PI 600 Trim Types Physical & Chemical Properties
More informationSeries Direct contact, metal-to-metal seating, make the globe valve ideal for most shut-off applications. Features
Direct contact, metal-to-metal seating, make the globe valve ideal for most shut-off applications. Features General application Designed for ASME boiler and pressure vessel code, section I applications
More informationYARWAY HANCOCK Y-PATTERN FORGED STEEL GLOBE STOP VALVES SERIES 4000
Direct contact and metal-to-metal seating make this Y-pattern globe stop valve ideal for most shut-off applications. FEATURES All valves feature integral Stellite hardfacing on both body and disc seating
More informationTABLE OF CONTENTS FORGING AHEAD OF THE REST
ORGED STEEL VLVES YO Valve Co., Ltd ddress: NO. 111, CaoliRoad, engjing Town,Jinshan District,Shanghai, China. TEL: 86-21-67360922 X: 86-21-67360966 Post Code: 201502 E-Mail: info@yaaovalve.com Website:http://www.yaaovalve.com
More informationbrands you trust. CRANE - Cast Steel Valves
brands you trust. CRANE - Cast Steel Valves Features & Benefits Key Features & Benefits All seat rings are seal welded as standard Quality process fully documented, materials fully traceable Full range
More informationFORGED HIGH PRESSURE BONNETLESS. ASME CLASSES: Sizes: 1 2 4" ( mm) U.S. Patent # Patented Easy Maintenance!
FORGED HIGH PRESSURE BONNETLESS ASME CLASSES: 1690 4500 Sizes: 1 2 4" (15 100 mm) U.S. Patent # 4356832 Patented Easy Maintenance! PROFILE Velan is one of the world's leading manufacturers of industrial
More informationSERVICE FEATURES CAST STEEL VALVES PRODUCTION RANGE PRODUCTION MATERIALS. Class Type UNIT : NPS GATE
API 600 Cast Steel Valves 1 SERVICE FEATURES Several trim combinations available for various services. Straight-through port design offering a good flow with minimum frictional loss and turbulence. Cast
More informationY -PATTERN GLOBE VALVES
Y -PTTERN GLOBE VLVES Low operation torque design. Rising and rotating stem for the most PI 602 design simplicity. Flanged valves are provided with fl anges integral with the body forgings. Outside Screw
More informationCast Steel Valves. General Index. Figure Number Index JENKINS -1-
Cast Valves Cast Valves SINCE 1864 General Index General Data... 2 Materials... 2 Identification... 3 Gate Valve Features... 4, 5 Globe Valve Features... 9, 10 Swing Check Valve Features... 14, 15 Pressure/Temperature
More informationLarge bore valves. Powergeneration / petrochemical industries. Medium & high-pressure valves in accordance with ASME, EN, BS and API
Large bore valves Powergeneration / petrochemical industries Medium & high-pressure valves in accordance with ASME, EN, BS and API An introduction to Key Valve Technologies Ltd. Key Valve Technologies
More informationCast Steel Valves. Contents Contents. Figure Number Index. Figure Number Cross Reference. Valve Type Class Stockham Jenkins
Stockham Cast Valves Cast Valves Contents Contents Performance in Any Application...4 How to Specify and Order Valves...4 Installation, Marking and Identification...5 Gate Valves...6 Globe Valves...11
More informationCast Steel Valves. General Index. Figure Number Index -1-
Cast Valves General Index Cast Valves Ordering Information... 2 General Data... 3 Materials... 4 Identification... 5 General Features... 6 Gate Valve Features... 7 NACE Trim Valves...11 Globe Valve Features...12
More informationFeatures and Description of Edward Univalve Globe Valves
Features and Description of Edward Univalve Globe Valves 7. 8. 9. 1 10. 2. 11. 12. 3. 4. 5. 6. 1. Stem has ACME threads, is ground to a fine finish and is hardened to resist wear. 2. Yoke bushing material
More informationarflu globe valves The quality you can trust Globe valves Because of their configuration,
The quality you can trust globe valves 2 18 Globe valves Because of their configuration, globe valves are perfect to regulate or limit the fluid port. epending on the needs of the system, design or open
More informationKE Series. Through Conduit, Double Expanding Gate Valves
KE Series Through Conduit, Double Expanding Gate Valves The KE Series is an advanced API 6D designed gate valve that provides a tight mechanically activated seal. It has double sealing, bi-directional
More informationDistributed by: M&M Control Service, Inc brands you trust.
Distributed by: M&M Control Service, Inc. /stockham.php 800-876-0036 847-356-0566 brands you trust. STOCKHAM - Cast Valves Contents Performance in Any Application...4 How to Specify and Order Valves...4
More informationDSI Valves. Pressure Seal Carbon, Chrome and Alloy Gate, Globe and Check Valves. REQUEST A QUOTE SCHEDULE SERVICES
DSI Valves Pressure Seal Carbon, Chrome and Alloy Gate, Globe and Check Valves REQUEST A QUOTE sales@dkamans.com SCHEDULE SERVICES 562-529-8400 WWW.DKAMANS.COM Z Y - T E C H G L O B A L I N D U S T R I
More informationCondensed Valve Guide Gate Globe Check Ball Strainer. Warren Valve - Quality Since 1963
800.231.6969 Condensed Valve Guide Gate Globe Check Ball Strainer Warren Valve - Quality Since 1963 Gate, Globe & Check Valves #1156 #2156 #3156 Gate Globe Check Pressures Class Figure 150 - #1156 300
More informationCAST STEEL FLANGED GATE, GLOBE, & CHECK VALVES.
CAST STEEL FLANGED GATE, GLOBE, & CHECK VALVES www.fnw.com Index Options & Accessories... 2 Standards... 2 Figure Number Matrix... 3 Pressure/Temperature Ratings... 3 Hydrostatic Test Pressures... 3 Carbon
More informationGate Valve (Model 1000)
Gate Valve (Model 1000) s: - 2 to 24 (50mm to 600mm) Rating: - Class 150 to Class 2500 Cast Steel Valves Flange End But-Weld End Information:- www.invacovalves.com sandesh@invacovalves.com invacovalves@gmail.com
More informationFORGING AHEAD OF THE REST
Bonney orge The Name You Trust for orged Steel Valves Bonney orge's forged steel valves and piping components have led the way for over eighty years in state-ofthe-art design and dependable performance.
More informationAN ISO 9001 : 2008 COMPANY GLOBE VALVES. Get the edge in process control. Butterfly Valves India Pvt. Ltd.
N ISO 9001 : 2008 OMPNY GLOE VLVES Get the edge in process control utterfly Valves India Pvt. Ltd. Introduction Hi-TEH Manufacturing Programme Valve Type End SME 2 2½ 3 4 5 6 8 10 12 onn. lass DESIGN STNDRD
More informationThe bolted bonnet configuration achieves simultaneously the best performance and the highest safety.
The achieves simultaneously the best performance and the highest safety. Features A rugged body and bonnet design in accordance with API 600, ASME B16.34 and BS 1414. Tight shutoff performance is always
More informationHANCOCK 600 GATE, GLOBE AND CHECK VALVES FORGED STEEL
HANCOCK 600 GATE, GLOBE AND CHECK VALVES A range of ASME class 800 and 1500 reduced bore forged steel valves with screwed, socket weld, butt weld or flanged ends GATE VALVES A compact but extremely sturdy
More informationGATE VALVES ALV-1 FORGED STEEL NOMINAL PRESSURE NOMINAL SIZE MATERIALS CONNECTIONS. ANSI Class PN /4-2 DN 8-50.
FORGED STEEL GTE VLVES LV-1 NOMINL PRESSURE NSI Class 150-1500 PN 16-250 NOMINL 1/4-2 DN 8-50 MTERILS Carbon Steel Low lloy Steel Stainless Steel CONNECTIONS Socket Weld Butt Weld Threaded Flanged XELVLVES
More informationAN ISO 9001 : 2008 COMPANY SWING CHECK VALVE. Get the edge in process control. Butterfly Valves India Pvt. Ltd.
N ISO 9001 : 2008 COMPNY SWING CHECK VLVE Get the edge in process control utterfly Valves India Pvt. Ltd. Introduction Hi-TECH Manufacturing Programme Valve Type End SME 2 2½ 3 4 5 6 8 10 12 14 16 18 20
More informationDirect contact, metal-to-metal seating, make the gate valve ideal for most shutoff applications. Class 800 ANSI.
Direct contact, metal-to-metal seating, make the gate valve ideal for most shutoff applications. Class 800 ANSI. Features Two inch and smaller valves are available with threaded or socket weld ends as
More informationbrands you trust. CRANE - Cast Steel Valves Crane ChemPharma & Energy
brands you trust. CRANE - Cast Steel Valves Features & Benefits Key Features & Benefits All seat rings are seal welded as standard Quality process fully documented, materials fully traceable Full range
More informationTECHNICAL DATASHEET Pacific CSV Cast Steel Valves
brands you trust. TECNICA DATASEET Pacific CSV Cast Steel Valves Crane ChemPharma & Energy Gate, Globe and Check Features and Benefits The new Pacific CSV valves have been redesigned to improve performance
More informationFUNCTION BODY AND BONNET BODY-BONNET JOINT
GATE VAVE FUNCTION Gate valve is characterized by a sliding wedge which is moved by actuator perpendicular to the flow direction. There are a variety of valve sizes and types. The valve is used primarily
More informationTECHNICAL DATASHEET Pacific CSV Cast Steel Valves
brands you trust. TECNICA DATASEET Pacific CSV Cast Steel Valves Crane ChemPharma & Energy Gate, Globe and Check Features and Benefits The new Pacific CSV valves have been redesigned to improve performance
More informationJordan Control Valve Series
Jordan Control Valve Series JCVS Globe Style Control Valves Mark ED and ET Globe Style Control Valves The Mark ED and ET are single port, globe style bodies with composition or metal seats, and a balanced
More informationSpecifications. Body Materials: Carbon steel, stainless steel, chrome-moly steel, other castable alloys
CONTROL VLVES KOSO HMMEL DHL B U L L E T I N V 5 0 / 5 0 - FETURES Globe bodies for in-line service; angle bodies for difficult service. Each body style accepts all standard trim sets. Balanced plugs for
More informationFisher D and DA Control Valves
D and D Valves Product Bulletin Fisher D and D Control Valves Fisher D and D single port, high pressure valves are widely used in oil and gas production industries. These valves are especially useful for
More informationDBOY Series Pneumatic Control Valve
Applications Process control systems for food, pulp and paper, chemical, petrochemical & other industries HVAC systems Feed water and fuel system controls in boiler rooms Packaged systems (OEM) such as
More informationGlobe valves Shut-off check valve 200 AE/BE PN DN Globe valves Lift check valve 240 MT PN DN 10-50
Globe valves Shut-off check valve 200 AE/BE PN 10-160 DN 10-50 Globe valves Lift check valve 240 MT PN 10-160 DN 10-50 Admissible operating pressure [bar] at design temperature [ C] 1) Material PN -200-60
More informationDirect contact, metal-to-metal seating, make the gate valve ideal for most shut-off applications. Class 800 ANSI.
Direct contact, metal-to-metal seating, make the gate valve ideal for most shut-off applications. Class 800 ANSI. Features Two inch and smaller valves are available with threaded or socket weld ends as
More informationSpecifications. Body Materials: Carbon steel, stainless steel, chrome-moly steel, other castable alloys
CONTROL VLVES KOSO HMMEL DHL B U L L E T I N V 5 1 0 / 5 2 0-1 FETURES Globe bodies for in-line service; angle bodies for difficult service. Each body style accepts all standard trim sets. plugs for use
More informationBULLETIN August 2009 PERMASEAL PLUG VALVE. ISO 9001:2008 Certified QMS. SMG Valves A Unit of Southern Manufacturing Group, Inc.
BULLETIN 13.01-01 August 2009 PERMASEAL ISO 9001:2008 Certified QMS SMG Valves A Unit of Southern Manufacturing Group, Inc. Design and Construction Permaseal Plug Valves are designed for on-off and diverting
More informationH i g h P r e s s u r e V a l v e
High Pressure Valve HIGH PRESSURE VALVES Applications & Specifications Range Gate Valve Advantages STRACK has designed and manufactured high pressure valves for over 35 years. Currently more than 3000
More informationSVF FLOW CONTROLS. Series # Flanged Standard Port Fire Safe / API th Edition. Performance Engineered I N C O R P O R A T E D
Series 41 150# Flanged Standard Port Fire Safe / API-607 4 th Edition 1 PIECE REDUCED PORT BALL VALVE UNITS = INCHES SIZE CLASS 150 WEIGHTS L H W 1 1/2 11 6.50 3.86 9.06 2 21 7.01 4.65 9.06 3 40 7.99 5.98
More informationRAIMONDI. High pressure forged globe valves to guarantee the pressure envelope integrity on harsh services.
Fig. 6022-6025 RAIMONDI High pressure forged globe valves to guarantee the pressure envelope integrity on harsh services. Features Forged body materials of highest quality, all in compliance with ASME
More informationInstallation, Operation, and Maintenance Manual Full Port Y-Pattern, Bolted Bonnet, Globe and Check Valves
SMITH VALVES Installation, Operation, and Maintenance Manual Full Port Y-Pattern, Bolted Bonnet, Globe and Check Valves Globe Valve Series: YG80/YG15 Welded Bonnet Globe Valve Series: YG87/YG17 Piston
More informationGate, Globe & Check Valves Corrosion-resistant
Gate, Globe & Check Valves Corrosion-resistant ASME Class 0 to 00 " - " (0 mm - 00 mm) API 0, ASME B. L&T Valves Trusted by the industry for over five decades, L&T Valves offers innovative products and
More informationM Series Floating Metal Seat Ball Valve
M Series Floating Metal Valve 1 M Series Floating Metal Valve Full Bore Two-piece Flanged Ends ANSI 150/300/600LB The A-T Controls M Series metal seat ball valve is designed for use in severe services
More informationWellhead Valves. DHV Industries,Inc. DHV Valve Company Inc.
DHV Industries,Inc. 3451 Pegasus Drive, Bakersfield. CA 93308 U.S.A. Call TollFree: (887) DHV-USA1 Phone: (661) 392-8948 Fax: (661) 392-8947 E-mail: sales@dhvindustries.com Website: www.dhvindustries.com
More informationCondensed Valve Guide Gate Globe Check Ball Strainer. Warren Valve - Quality Since 1963
800.231.6969 Condensed Valve Guide Gate Globe Check Ball Strainer Warren Valve - Quality Since 1963 Gate, Globe & Check Valves #1156 #2156 #3156 Gate Globe Check Sizes ½"-36" Pressures Class Figure 150
More informationKunkle Models 91/218/228 liquid relief valves Safety and relief products
Cast iron liquid relief valves with bronze trim including models UL and FM approved for fire pump installations Model 228 Features Bolted bonnet allows easy inspection and servicing without removal from
More informationKunkle Models 91/218/228 liquid relief valves Safety and relief products
Cast iron liquid relief valves with bronze trim including models UL and FM approved for fire pump installations Model 8 Features Bolted bonnet allows easy inspection and servicing without removal from
More informationACADs (08-006) Covered 1.3.1.7 1.3.9.2 2.1.6.1 2.1.6.2 2.1.6.4. 2.1.7.1 2.1.7.2 2.1.7.6 5.2.1.10 5.4.1.4 5.4.3.5 Keywords Gate, ball, butterfly, diaphragm, globe, regulate, throttle, back flow, relief,
More informationHoneywell EN REV. 2 09/2014 Page 1 of 10 Specification
Series 9110 Single/Double Seated Globe Valves for ANSI 150-600 DIN/BS 4504 PN10-PN40 Honeywell 70-16-10-05 EN REV. 2 09/2014 Page 1 of 10 Specification Series 9110 Single/Double Seated Globe Valves for
More informationLVS SUP-R-SEAL MODEL ES GATE VALVES
LVS SUP-R-SEAL MODEL ES GATE VALVES LOUISIANA VALVE SOURCE INC. LOUISIANA VALVE SOURCE INC. PROUDLY MADE AND ASSEMBLED IN USA May 2012 Page 1 www.lavalve.com ENGINEERING BULLETIN 2014 Table of Contents:
More informationM&J Valve Product Overview
M&J Valve Product Overview M&J Valve was founded in 1962 by Marvin Grove and has been a leader in the pipeline valve industry since its inception. Now part of SPX FLOW, M&J Valve meets or exceeds the quality
More informationVB VALVES & AUTOMATION
Introduction to Valve What are Valves? Valves are mechanical device that controls the flow and pressure within a system or process. They are essential components of a piping system that conveys liquids,
More information78200/18200 Series LINCOLNLOG Valves Anti-cavitation High Pressure Control Valves
LINCOLNLOG Valves Anti-cavitation High Pressure Control Valves Featuring High Resistance Multiple Stage LINCOLNLOG Trim Angle Configuration 78200 Globe Configuration 18200 Specification Data CP6020 10/97
More informationSERIES VARISTEP CONTROL VALVES
1-6962 SERIES VARISTEP CONTROL VALVES Introduction Cavitation is a well-known phenomenon which frequently occurs when high liquid pressure drops associated with relatively high temperatures are handled
More informationMSA, a.s., is an important manufacturer of industrial valves from the Czech Republic, Europe. The company manufactures and sells wide range of
API Program MSA, a.s., is an important manufacturer of industrial valves from the Czech Republic, Europe. The company manufactures and sells wide range of industrial valves for transport and processing
More informationEdward. Equiwedge Forged Gate Valvee. Experience In Motion
Edward Equiwedge Forged Gate Valvee Experience In Motion Superior sealing performance. Improved process integrity and productivity. The higher operating pressures and temperatures of today s supercritical
More informationMaximum leakage rate is less than half of the AWWA allowable Can be adapted to any channel Low-maintenance gates ***
Maximum leakage rate is less than half of the WW allowable Can be adapted to any channel Low-maintenance gates *** The Fontaine gate is designed to control water flows in channels. It is the same construction
More informationCAST STEEL GATE VALVE
CAST STEEL GATE VALVE DESIGN CHARACTERISTICS OF API00 CAST STEEL GATE VALVE The design of thrust bearing makes valve opened easily and flexibly. Handwheel Nut Handwheel Stem Nut Retainer Stem Nut Lubricating
More informationAIL METSEAL Butterfly Valves
AIL METSEAL Butterfly s The AIL METSEAL Butterfly is a high performance valve which is used for positive isolation in Power Generation, Petroleum Refining, Oil and Gas Production, Chemical, Petrochemical
More informationw w w.fastwell.in FORGED STEEL VALVES GATE, GLOBE & CHECK PRESSURE CLASS: ASME SIZE RANGE : 1/4-3 API STANDARDS : 602 ASME B16.
A trusted name in industrial valve company FORGED STEEL VALVES GATE, GLOBE & CHECK PRESSURE CLASS: ASME 150-2500 SIZE RANGE : 1/4-3 API STANDARDS : 602 ASME B16.34 CATALOG NUMBER FFI -1004 TABLE OF CONTENTS
More informationL&T VALVES BUSINESS GROUP A
Larsen & Toubro Limited (L&T) is a US $ 5 billion engineering and construction company, with a strong presence in manufacturing, services and Information Technology. L&T was founded in 1938 by two Danish
More informationProven technology for individual valve solutions worldwide. GWC Valve International
Proven technology for individual valve solutions worldwide FORGED STEEL VALVES GATE, GLOBE & CHECK PRESSURE CLASS: ASME 150-2500 SIZE RANGE: 1/4-3 API STANDARD: 602 ASME B16.34 Catal og Nu mb er f SV-
More informationGWC Italia. Proven technology for individual valve solutions worldwide FSV-1005
GWC Italia Proven technology for individual valve solutions worldwide forged STEEL VALVES GATE, GLOBE & CHECK FSV-1005 2 GWC ITALIA Proven technology for individual valve solutions worldwide w w w. g w
More informationValve Selection. 1. Function and service considerations
1. Function and service considerations Valve Selection Selection Valves serve the purpose of controlling the fluids in building services piping. Valves are produced in a variety of design types and materials.
More informationFisher 585C Series Piston Actuators
Instruction Manual D102087012 585C Actuator Fisher 585C Series Piston Actuators Contents Introduction... 1 Scope of Manual... 1 Description... 2 Specifications... 2 Educational Services... 2 Principle
More informationOSV. Forged Steel Valves Technical book OSV
OSV Forged Steel Valves Technical book OSV Principles Of Company General Introduction Company History About the company OS Valves (OSV) is a subsidiary of OS Company. OSV has been inspiring our employees
More informationECOLINE GTC Type Series Booklet
Gate Valve ECOLINE GTC 150-600 Class 150-600 NPS 2''-36'' Cast Steel / Stainless Steel Bolted Bonnet Flanged Ends Type Series Booklet Legal information/copyright Type Series Booklet ECOLINE GTC 150-600
More informationType K03. Gate Valve Butt-Welded, Flanged DN PN Data Sheet Edition: EN 9 / together we are strong
PN 16 100 Gate Valve Butt-Welded, Flanged Data Sheet Edition: EN 9 / 2015 MPOWER Engineering, a.s. Pod vinicí 2028/20, Modřany, 143 00 Praha 4, CZ T: +420 225 371 300, F: +420 225 371 325 E: info@mpowergroup.eu,
More informationBolted bonnet configuration
The bolted bonnet type valves are manufactured to guarantee the highest performance in the widest spectrum of oil and gas applications Features Swing check valves can fit on both horizontal and vertical
More informationCrane. UNI-CHEK High Performance Check Valves
Crane UNI-CHEK High Performance Check Valves High Performance Uni-Chek Valves for Backflow Prevention In almost every piping system, there is a need for backflow prevention. Most piping systems utilize
More informationKO Series. Cast Steel Gate Valves
FEATURES & BENEFITS Body and bonnet of Class 150 - Class 900 gate valves are usually connected with studs and nuts. The body and bonnet of Class 1500 - Class 2500 gate valves are usually a pressure sealed
More informationPlease note this is a condensed catalog. For a complete version, contact Velan directly.
Please note this is a condensed catalog. For a complete version, contact Velan directly. VELAN VALVES IN POWER With an installed base covering over 300 nuclear power plants and over 2,000 thermal power
More informationInternational Standard Valve, Inc. Slab and Expanding Gate Valves
International Standard Valve, Inc. TM ISV Series GTDS & GTDE Slab and Expanding Gate Valves 2 through 36 ASME Class 150-2500 Top Entry Bolted Body Flanged & Weld Ends API 6D Fire Safe Design NACE is a
More information41005 Series Control Valves. Specification Data CH /10
Putting You In Control Specification ata CH41005 11/10 41005 Series Control Valves Complete Line of Heavy uty, Balanced, Cage Guided, Globe Valves with Lo-dB Anti-Cavitation Capabilities resser Masoneilan
More informationSeries 2200 and 2220 Control Valves
Series 2200 and 2220 Control Valves Space-Saving Solution: Yokeless design fits tight separator and scrubber applications Series 2200 Series 2220 Norriseal Series 2200 and 2220 control valves have been
More informationFIGURE NO. VALVE TYPE PRESSURE CLASS CONNECTIONS SIZE RANGE PAGE NO. 28 Stop Check Valve 300 Flanged 3" 10" 30
Cast Valves General Index Cast Valves Figure Number Index Ordering Information... 2 General Data... 3 Materials... 4 Identification... 5 General Features... 6 Gate Valve Features... 7 NACE Trim Valves...11
More informationCorporate Overview... 2,3. How To Order Gate Valves Globe Valves Check Valves Cryogenic Valves...
FORGED STEEL VALVES Table Of Contents Corporate Overview... 2,3 How To Order... 4-8 Gate Valves... 9-14 Globe Valves... 15-22 Check Valves... 23-30 Cryogenic Valves... 31-40 Integral Flanged Valves...
More informationBOSS Series D Control Valve
Applications Process control systems for food, pulp and paper, chemical, petrochemical & other industries HVAC systems Feed water and fuel system controls in boiler rooms Packaged systems (OEM) such as
More informationGLS. globe control valve
globe control valve GLS INTRODUCTION The GL S globe control valve presents a superior performance, while providing an easy, quick and economical maintenance. Differently from other control valves operated
More informationExpanding & Slab Gate Valves
Global Energy Market Solutions CAST / FORGED BODY Expanding & Slab Gate Valves For oil and natural gas wellhead, flowline, manifold, fracture or other critical service applications requiring operating
More informationPETRO VALVES. Gate Globe Check VALVE CATALOGUE. Subsidiary of Petro Power UK
PETRO VALVES Gate Globe Check VALVE CATALOGUE Subsidiary of Petro Power UK 2 PETRO VALVES The company 4 GATE VALVES BOLTED BONNET from Class 150 up to Class 2500 from 2 up to 36 PRESSURE SEAL from Class
More informationVALVES AIL CAST STEEL GATE, GLOBE & CHECK AUDCO INDIA LIMITED. ASME Class mm mm (2-60 ) API 600 BS 1873 BS 1868 API 603
AIL CAST STEEL GATE, GLOBE & CHECK VALVES ASME Class 150-2500 50mm - 1500mm (2-60 ) API 600 BS 1873 BS 1868 API 603 ASME B16.34 API 6D AUDCO INDIA LIMITED Introduction AIL Cast Steel Gate, Globe and Check
More informationHydra Series Choke Valve **Patent Pending
Hydra Series Choke Valve product of GI Industries Hydroplex Choke Valve Hydroplex chokes are Multiple Orifice Valves (MOV) specifically designed to control high pressure liquids and gases while providing
More informationGWC Italia. Proven technology for individual valve solutions worldwide CAST STEEL VALVES GATE, GLOBE & CHECK CSV-1004
GWC Italia Proven technology for individual valve solutions worldwide CAST STEEL VALVES GATE, GLOBE & CHECK CSV-1004 GWC ITALIA Proven technology for individual valve solutions worldwide GWC Italia Worldwide
More informationANSI GATE, GLOBE AND CHECK VALVES & STRAINERS
ANSI GATE, GLOBE AND CHECK VALVES & STRAINERS INDEX 2 8 16 20 32 36 44 50 54 58 62 66 78 THE COMPANY CAST GATE VALVES CAST GATE VALVES PRESSURE SEAL CAST GLOBE VALVES CAST GLOBE VALVES PRESSURE SEAL CAST
More informationD1 Series Top Guided Single Seated Control Valves
D1 Series Top Guided Single Seated Control Valves Model D1S Overview Model D1S globe control valves are with bolted bonnet and top guided contoured trims. The design facilitates easy access to internal
More informationTRUNNION BALL VALVES. TBV 7.10
TRUNNION BALL VALVES WWW.VALVE.COM TBV 7.10 ABOUT US Our mission at Universal Flow (), is to provide a quality product at a competitive price and to meet the needs and requirements of our customers in
More informationEXPG SBG API 6D EXPANDING/ SLAB GATE VALVES SERIES DEPEND ON US. WE CAN HANDLE THE PRESSURE.
API 6D Expanding/ Slab Gate Valves ANSI 150-300-600-900-1500 SERIES 2-36 EXPG SBG > Control > Flow Quality > lit API 6D EXPANDING/ SLAB GATE VALVES Providing Hundreds of Products. Supporting Thousands
More informationEdward Valves. EV100 5th Edition. Edward Valves Catalog & Application Manual
EV100 5th Edition Catalog & Application Manual EV100 5th Edition Introduction Forged Steel Valves Cast Steel Valves Special Application Valves Nuclear Application Valves Accessories/Actuators Technical
More informationThe series 10 butterfly valves has been developed for a large number of applications throughout process industries. The
Technical Bulletin B-100 Features Series 10 High Performance Feature Butterfly valves For Rating ANSI 150 General : The series 10 butterfly valves has been developed for a large number of applications
More information