REPAIR PARTS MANUAL. Lawn Tractor MODEL NO. HURRICANE 12.5SD ( ) Ihr Ersatzteilspezialist im Internet

Size: px

Start display at page:

Download "REPAIR PARTS MANUAL. Lawn Tractor MODEL NO. HURRICANE 12.5SD ( ) Ihr Ersatzteilspezialist im Internet"

Hannah Hubbard
6 years ago
Views:

1 REPAIR PARTS MANUAL MODEL NO. HURRICANE 1.5SD ( ) Lawn Tractor Rev AP Printed in U.S.A.

2 HOW TO USE THIS MANUAL This manual is designed to provide the customer with a means to identify the parts on his/her tractor when ordering repair parts. The illustrations may or may not represent the actual assemblies; therefore, it is not recommended to use this manual as a guide to assemble or disassemble the tractor. Some hardware and parts are drawn larger in order to more readily identify them. Each tractor has its own model number. The model number for your tractor can be found on the fender under the seat. When ordering parts, always give the following information: Product - Tractor Model Number - HURRICANE 1.5SD ( ) Part Number Part Description TABLE OF CONTENTS SCHEMATIC... 3 ELECTRICAL CHASSIS DRIVE...-9 STEERING ENGINE SEAT...14 MOWER LIFT MOWER DECK DECALS... 1

3 SCHEMATIC 03049_ BATTERY SOLENOID STARTER RED A AMMETER (OPTIONAL) RED FUSE RED M B S M G A1 L A BLUE WHITE CLUTCH / BRAKE (PEDAL UP) ATTACHMENT CLUTCH (CLUTCH OFF) BLACK BLACK BLACK SEAT SWITCH (NOT OCCUPIED) BLACK GRAY GRAY BLACK REVERSE SWITCH SHORTING CONNECTOR NOT IN REVERSE BLACK BLACK/WHITE IGNITION UNIT SPARK PLUGS GAP ( PLUGS ON TWIN CYL. ENGINES) BLUE FUEL SHUT-OFF SOLENOID FUEL LINE HOUR METER (OPTIONAL) BLACK BLUE RED (IF SO EQUIPPED) CHARGING SYSTEM OUTPUT 3 AMP 3600 RPM VOLTS AC 3600 RPM (CHARGING SYSTEM DISCONNECTED) LIGHTING SYSTEM OUTPUT 5 AMP 3600 RPM ALTERNATOR DIODE IGNITION SWITCH POSITION CIRCUIT MAKE OFF RUN/OVERRIDE RUN M+G+A1 B+A1 B+A1 L+A START B+S+A NOTE YOUR TRACTOR IS EQUIPPED WITH A SPECIAL ALTERNATOR SYSTEM. THE LIGHTS ARE NOT CONNECTED TO THE BATTERY, BUT HAVE THEIR OWN ELECTRICAL SOURCE. BECAUSE OF THIS, THE BRIGHTNESS OF THE LIGHTS WILL CHANGE WITH ENGINE SPEED. AT IDLE THE LIGHTS WILL DIM. AS THE ENGINE IS SPEEDED UP, THE LIGHTS WILL BECOME THEIR BRIGHTEST. NON-REMOVABLE CONNECTIONS REMOVABLE CONNECTIONS WIRING INSULATED CLIPS NOTE: IF WIRING INSULATED CLIPS WERE REMOVED FOR SERVICING OF UNIT, THEY SHOULD BE REPLACED TO PROPERLY SECURE YOUR WIRING. 3

4 TRACTOR - MODEL NO. HURRICANE 1.5SD ( ), PRODUCT NO ELECTRICAL B 1 4

5 ELECTRICAL Battery 1 Volt 5 Amp Bolt Hex Hd 1/4-0 Unc x 3/ Battery Box Switch Interlock Push-In Cable Battery 6 Ga. 11"red Cable Battery Fuse Nut Keps Hex 1/4-0 unc Cable Ground 6 Ga. 1"black Switch Seat Switch Ign Key Ign Harness Ign Bolt Blk Fin Hex 1/ Cover Terminal Red Solenoid Adapter Ammeter Protection Wire Loop Cover Terminal Battery Harness Pigtail Consle ROS Screw Plastite x Module Reverse ROS NOTE: All component dimensions given in U. S. inches 1 inch = 5.4 mm. 5

6 CHASSIS AND ENCLOSURES Chassis-Elite_Basic_LT_7 6

7 CHASSIS AND ENCLOSURES Chassis Drawbar Bumper, Hood/Dash Saddle Clip Retainer Slide-On Dash Bolt, Carriage 3/-16 x Panel Dash LH Panel Slkscr Dash RH Screw Mach TRHD 5/16-1 unc x 3/ Nut Keps 5/16-1 Unc Hood Bumper Hood Bolt Fin Hex 3/-16 unc x 1 Gr Washer 13/3 x 13/16 x 1 Ga Nut Lock Hex w/ins 3/-16 unc Grille Fender Bracket Fender Repl 10973x Footrest Pnt LH Footrest Pnt RH Bolt Rdhd Sht Sqnk 3/-16 x 3/ Screw Thdrol 5/16-1 x 1/ TYT Bracket Asm. Pivot Mower Rear Bracket Pivot Rod Pivot Chassis/Hood Screw Thdrol 3/-16 x 1/ Bolt Shoulder 5/ Screw Thdrol 3/-16 x 1/ Screw Hex Wsh Thdrol 3/ Screw 10 x 3/4 Single Lead-Hex Plug Button Blk 359 Dia Choke Plug Switch Light NOTE: All component dimensions given in U.S. inches 1 inch = 5.4 mm. 7

8 DRIVE

9 DRIVE Transaxle, Dana D600 (Order parts from transaxle manufacturer) Spring Return Brake T/a Zinc Pulley Transaxle 1" tires Ring Retainer # Strap Torque 30 Degrees Screw 5/16-1 x 3/ Rod Shifter Pin Cotter 1/ x 1 Cad Washer Plate Shf 3 Sq Hole Bolt 1/4- Unf Gr W/Patch Washer Lock Hvy Helical 1/ Bolt Hex Flghd 5/16-1 Gr Nut Lock Hx W/Ins 5/16-1 Unc Bolt, Fin Hex 3/-16 Unc x 1 Gr Nut Lock 3/-16 Unc Knob Rod Brake Blk Zinc Nut Hex Jam 3/-16 Unc Spring Rod Brake 00 Zinc Washer 13/3 x 13/16 x 16 Ga Pin Cotter 1/ x 3/4 Cad Rod Brake Parking Cap Brake Parking Bracket Mtg Tran sax le Bolt Hex Hd 5/16-1unc x 3/ Shaft Asm Pedal Foot Bearing Nylon Blk 69 Id Washer 1/3 x 1 x 16 Ga Pin Roll 3/16 x 1" Pulley Idler Composite Bolt Rdhd 3/-16 Unc x -3/4 Gr Keeper Belt Re tain er Idler Pulley Idler V Groove Plastic Bellcrank Asm Retainer Belt Style Spring Bolt Carr Sh 3/-16 x 1-1/ Gr Nut Crownlock 3/-16 Unc Nut Crownlock 5/16-1 Unc Link Clutch Spring Return Clutch Screw 3/-16 x 1-1/ V-Belt Traction Drive Keeper Belt Span Ctr Screw 3/-16 x Cover Pedal Blk Round Engine Pulley Bolt Hex Washer Lock Hvy Hlcl Spr 7/ Keeper Belt Engine Foolproof Screw Hex Wsh Hi-Lo 1/4 x 1/ unc Guide Belt Mower Drive RH Washer 5/3 x 1 1/4 x 16 Ga E-ring # Key Square 0 x 145/ Washer 5/3 x 1-5/ x 16 Ga Key Woodruff Arm Shift Transaxle Shaft Asm. Cross Taper Spring Torsion Shift Washer 17/3 x 3/4 x 16 Ga LinkTransaxle Nut Lock Center 1/ Console Asm Retainer Spring 1" Washer 9/3 x 3/4 x 10 Ga Strap Torque Lh Bolt Rdhd Sq Neck 3/-16 x Nut Lock Flg 3/ Spacer Retainer Washer 13/3 x x Washer Srrtd 5/16ID x 1.0 x.15tk Bracket Shift Mount Hub Shift Bolt RDHD SQNK 1/4-0 x 3/4 Gr Nut Crownlock 1/4-0 UNC Bolt Hex Fin 1/4-0 UNC x 1 Gr Bracket Pivot Lever Screw 5/16-1 x 5/ TT Yellow Shoulder Bolt 5/16-1 x Plate Fastening Keeper Belt T/A Nyliner Snap-in 5/" ID Washer Nyl Bolt, 3/ - 16 x 1-3/4 Gr Nut Flange Hex Lock Screw 3/-16 x 3/ Guard Muffler Washer 13/3 x 1 x 14 Ga. NOTE: All component dimensions given in U.S. inches 1 inch = 5.4 mm 9

10 STEERING steering_pl.lt_5 10

11 STEERING Wheel Steering Axle Asm Spindle Asm LH Spindle Asm RH Bearing Race Thrust Harden Washer 5/3 x 1-5/ x 16 Ga Washer 7/3 x 1-1/4 x 16 Ga Ring Klip #t Bearing Col Strg Blk Link Drag Washer Lock Hvy Hlcl Spr 3/ Spacer earing Axle Front Hexflange Lock Shaft Asm Strg Bushing Link Drag Blk LR Washer 13/3 x 7/ x 16 Ga Screw 3/-16 x 3/ Pin Cotter 1/ x 3/4 Cad Rod Tie Wire Form Mech Washer Lock 5/ Bushing Strg 5/ Id Dash Screw Cap Wheel Steer Washer 11/3 ID x 3/ OD x 1 Ga Nut Crownlock 3/ Adaptor Wheel Strg Boot Steering Washer 5/3 x 1 1/4 x 16 Ga Extension Steering Cap Spindle Fr Top Blk Fitting Grease Spacer Brace Axle Bolt RdHd Sqnk 3/-16 x -1/ Brace Axle Steering Asm Bracket Susp Chassis Front Bolt shoulder 7/ Clip Steering Washer Hardened Bolt 5/16-1 UNC x 4" L Gr. 5 NOTE: All component dimensions given in U.S. inches 1 inch = 5.4 mm. 11

12 ENGINE OPTIONAL EQUIPMENT 3 Spark Arrester engine-bs.1cyl_3 1

13 ENGINE Control Throttle /Choke Screw Hex Thd Cut 1/4-0 x 5/ T Engine Briggs Model 1907 (Order Parts from Engine Manufacturer) Muffler Exhaust Gasket Tube Drain Oil Easy Shield Browning/Debris Guard Control Choke Arrestor Spark Tank Fuel Cap Asm Fule Top Clamp Hose Blk Line Fuel 0" Plug Drain Oil Easy Bushing Snap Screw Hexwsh Thdrol 3/-16 x 3/ Screw 3/-16 x 3/ Washer 9/3 x 7/ x 16 Ga Washer Lock Hvy HLCL Spr 5/ Screw Socket Hd x Screw 3/-16 x 1-1/ Nut Keps Hex 1/4-0 unc NOTE: All component dimensions given in U.S. inches 1 inch = 5.4 mm Engine Power Rating Information The gross power rating for individual gas engine models is labeled in accordance with SAE (Society of Automotive Engineers) code J11940 (Small Engine Power & Torque Rating Procedure), and rating performance has been obtained and corrected in accordance with SAE J1995 (Revision 00-5). Actual gross engine power will be lower and is affected by, among other things, ambient operating conditions and engine-to-engine variability. Given both the wide array of products on which engines are placed and the variety of environmental issues applicable to operating the equipment, the gas engine will not develop the rated gross power when used in a given piece of power equipment (actual on-site or net horsepower). This difference is due to a variety of factors including, but not limited to, accessories (air cleaner, exhaust, charging, cooling, carburetor, fuel pump, etc.), application limitations, ambient operating conditions (temperature, humidity, altitude), and engine-to-engine variability. Due to manufacturing and capacity limitations, Briggs & Stratton may substitute an engine of higher rated power for this Series engine. 13

14 SEAT seat_lt.bolt_ Seat Bracket Seat Pivot Bolt Hex 3/ - 16 x Washer 13/3 x 1 x 10 Ga Clip Push-In Hinged Nut Lock Hex w/ins 3/ Spring Seat Cprsn 50 Blk Zi Screw 3/-16 x Washer 13/3 x 1 x 14 Ga Pan Pnt Seat (Blk) Bracket Pnt Mounting Switch Bushing Snap Blk Nyl Bolt Rdhd Sht Nk 1/4-0 x 1-1/ Spacer Split. x Spring Cprsn Nut Lock 1/4 Lge Flg Bolt Shoul der 5/16-1 unc-a Nut Lock Hex w/ins 5/ Bolt Hex Black Washer 17/3 x 1-3/16 x 1 Ga Bolt Shoul der 5/16-1 x Washer Lock Hvy Hlcl Spr 1/ NOTE: All component dimensions given in U.S. inches 1 inch = 5.4 mm. 14

15 DECALS Decal, Deflect Wrn Cutfinger Sym Decal Engine Decal, Brake/Clutch Decal, Hot Muffler Decal, Warning Engine Sym Decal, DB/CE Decal, Read Owner's Manual Decal, V-Belt Sch Decal, Parking Brake Decal, Cut Finger Decal, Strg. Wheel Decal, Hood Decal, Caution, Battery Decal, Drawbar Decal, Handle Lft Height Adj Manual, Operator's, Euro Manual, Operator's, Scan Manual, Operator's, EBloc Manual, Operator's, Baltic Manual Parts WHEELS & TIRES 1 6 5, 7 4,10 3, Cap, Tire valve Stem, Valve Tire, Front Tube, Front (Service item only) Rim assembly, 6" front Fitting, Grease (Front wheel only) Bearing, Flange (Front wheel only) Rim assembly, " rear Tire, Rear Tube, Rear (Service item only) Cap, Hub Axle Sealant, Tire (10 oz. Tube) NOTE: All component dimensions given in U.S. inches 1 inch = 5.4 mm wheel_1 15

16 MOWER DECK _deck-manual_4 16

17 MOWER DECK Mower Housing Assembly Bolt Carriage 5/16-1 x 3/ Bracket Asm Fr. Sway Bar Bracket Deck Sway Bar 3"/4" Retainer Spring Bar Sway Deck Nut Lock Hex w/ins. 5/16-1 unc Bolt 3/-4 x 1.5 Gr Blade Mower Shaft Assembly, Mandrel, Vented Housing, Mandrel, Vented Bearing, Ball, Mandrel Bolt Rdhd Sqnk 5/16-1 x 5/ Bolt, Shoulder Baffle Vortex Front Nut Bracket, Mower Deflector Cap, Sleeve Spring, Torsion, Deflector Nut, Push Shield, Deflector Rod, Hinge Screw Thdrol Washer, Spacer Pulley, Mandrel Nut, Toplock Pulley, Idler, Flat Pulley Idler Flat Nut, Crownlock 3/-16 unc Retainer Spring Idler Arm Assembly Spacer, Retainer Knob V-Belt Spring Brake Return Washer 13/3 x 13/16 x 11 Ga Spacer Retainer Stiffener, Idler Arm Rod, Brake LH Rod, Brake RH Keeper Belt Idler Tension Spring Return Idler Retainer Spring Yellow Washer 9/3 x 3/4 x 10 Ga Clutch Cable 3"/46" Screw Hex Thd Cut 1/4-0 x 1/ Head Asm Cable Clutch Screw Hex Wsh Thdrol 3/-16 x -3/ Keeper Belt Bolt Carriage Idler Stand, Brake Arm, Brake Spacer, Brake Bolt/Washer Asm 5/ Keeper Belt Rh Mandrel Guard Brake Washer Brake Assembly (Includes Stand, Arm and Guard Components) Mandrel Assembly (Includes Housing, Shaft and Shaft Hardware Only - Pulley Not Included) Replacement Mower, Complete NOTE: All component dimensions given in U.S. inches 1 inch = 5.4 mm 17

18 MOWER LIFT lift-rh.1piece_ Wire Asm Inner/Sprg w/plunger Shaft Asm Lift RH Pin Groove E Ring # Washer 1/3 x 1 x 1 Ga Bearing Nylon Blk 69 Id Grip Handle Bicycle Matte Blk Button Plunger Black Link Lift LH Fixed Length Link Lift RH Fixed Length Retainer Spring Link Front Nut Jam Hex 1/-13 unc Trunnion Nut Lockw/Wsh 1/-13 unc Arm Suspension Rear Pin Cotter 7/16 Bow Tie Bearing Pvt Lift Nut Crownlock 3/ Pin Cotter 5/16 Bow Tie NOTE: All component dimensions given in U.S. inches 1 inch = 5.4 mm. 1

19 SERVICE NOTES 19

REPAIR PARTS MANUAL MODEL NO. REB13038 ( ) LAWN TRACTOR

REPAIR PARTS MANUAL MODEL NO. REB13038 (901107901) LAWN TRACTOR 3 4 98-3 Rev. HOW TO USE THIS MANUAL This manual is designed to provide the customer with a means to identify the parts on his/her tractor