MAGNUM SMA8 and SMH10 Assembly Manual
|
|
- Warren Casey
- 5 years ago
- Views:
Transcription
1 MAGNUM SMA8 and SMH10 Assembly Manual
2 Please note that this manual uses a MAGNUM SMA8 in all the images. The SMH10 has some very slightly different parts, but the assembly process is identical. Step 1 Locate the top and front chassis sections. Top Front Remove the front cover from the front chassis, and set aside. These parts have orientation markers for front and top. F is for front and T is for the top. These orientation markers will be used throughout the assembly process.
3 Join the top of the front chassis to the front of the top chassis using the bag of countersink screws. Step 2 Turn the assembly on its side so that the top chassis is on the floor.
4 Locate the chassis divider and join the parts as shown. It is best to insert the screws that go in the front chassis first, then insert the screws into the top chassis. Note that the smooth side of the divider is facing inwards. Chassis Divider Step 3 Locate the chassis mid plate and join the parts as shown. It is best to insert the screw which is next to the second cable management hole (in the center of the part) first. Chassis Mid Plate
5 Step 4 Turn the assembly on to its side. Locate the bottom chassis and join the parts as shown. Please note the F orientation marker on the part. Bottom Chassis
6 Step 5 Turn the assembly on to the front as shown. Locate the rear chassis and the L shaped hinges from the door hinge kit. Rear Chassis L shaped hinges
7 Attach the hinges to the rear chassis with the bag of screws in the door hinge kit.
8 Join the rear chassis as shown. Again, note the F orientation marker. Step 6 The case feet, or optional casters, can now be installed on the bottom.
9 The case can now be turn right side up. Step 7 Locate the drive cages and the nut driver kit. Drive Cages Nut Driver Kit
10 Attach the cages as shown. Step 8 Locate the switch assembly and attach as shown.
11 Step 9 Locate the clip kit and attach the clips to all stand off locations around the case. Step 10 Locate the PCI backplate, motherboard tray and motherboard tray handle. There will be screws taped to the wrapping on PCI backplate, these will be used to attach the backplate to the tray.
12 Slide the motherboard tray into the guides on the divider. Attach the motherboard tray handle to the PCI backplate.
13 Install the PCI backplate on to the rear chassis, but leave slightly loose. Then attach to the motherboard tray where the arrows indicate. Once the motherboard tray assembly is assembled, check to make sure it slides freely, but is also not too loose.
14 The top guide is adjustable to insure a proper fit. If the tray is in need of adjustment, loosen the screws indicated below. Then retighten with the desired tension. Step 11 Locate doors and the remaining parts from the door hinge kit. If you door has a window, there is a protective backing which needs to be peeled off.
15 Attach the hinges as shown. Please note that the flat side of the hinge is facing up. Once the hinges are attached the doors can be installed. Step 12 Locate the top cover and lower side covers. Lower Side Covers Top Cover (standard shown)
16 Note that one side of the top cover has an extra bend. This bend is the front of the top cover. Attach the side covers, top cover and front cover to the case. END.
MAGNUM TX10 Assembly Manual
MAGNUM TX10 Assembly Manual (Single and Dual Systems) Parts list: Front Chassis Section with attached Front Cover - 1 Top Chassis Section - 1 Bottom Chassis Section - 1 Rear Chassis Section - 1 Motherboard
More informationEZ LITE CRUISER. Service & Maintenance Manual
EZ LITE CRUISER Service & Maintenance Manual Table Of Contents Introduction to the EZ Lite Cruiser 3 Identification of Components 4 Controller System Component Diagram 6 Controller System I/O Ports Detail
More information4WD & 6WD Wheelchair ATR Assembly Manual
4WD & 6WD Wheelchair ATR Assembly Manual Follow this manual for assembly of the 4WD WC ATR and the 6WD WC ATR, as well as the 4WD and 6WD snowplow. The pictures in this manual are taken from any of these
More informationPrusa i3 Printer Assembly Guide
Prusa i3 Printer Assembly Guide Special thanks to Carlos Sanchez and Miguel Sanchez for the graphics. All graphics captured from their great animation: http://www.carlos-sanchez.com/ Prusa3/ For copyright
More informationCopyright Information. Document Information. Disclaimer. Trademark Information. Copyright 2010 by Oki Data. All Rights Reserved
Copyright Information Copyright 2010 by Oki Data. All Rights Reserved Document Information pro900dp Feeder/Conveyor Quick Assembly Instructions P/N 59405601 Revision 1.0 February, 2010 Disclaimer Every
More informationPowerBook G4 Aluminum 17" GHz Clutch Hinges Replacement
PowerBook G4 Aluminum 17" 1-1.67 GHz Clutch Hinges Replacement Written By: Andrew Bookholt ifixit CC BY-NC-SA www.ifixit.com Page 1 of 20 INTRODUCTION Replacing the clutch hinges also provides a new attached
More informationOne- Touch Installation Instructions
One- Touch Installation Instructions 1 1 Height Adjustable Pivot w/ screws 9 Upper Work Surface 2 Rail Mount Knobs 10 Back Cover 3 Transformer 11 Center Pivot w/ screws 4 Support Legs 12 Left Monitor Arm
More informationC15C C15C. Page 1 of 20
2 x Lid Front Hinge 1135 8 x M8 Bolt 8 x M8 Washer (3mm Thick) 4 x M6 Large washers 4 x M6 Spring washers 4 x M6 x 40mm Bolts 6 x M6 20mm Bolts 6 x M6 Washers 20 x Screws 2 x Lid mount gas strut bracket
More informationINSTALLATION INSTRUCTIONS
Rear Vision System Liftgate Emblem Camera Mirror Display 2009-2012 Ford Flex (Kit part number 1008-9527) Kit Contents: Mirror Liftgate Emblem Mount with Camera Interior (shorter) Harness Chassis (longer)
More informationTo safely lift and install this hardtop, you will need the assistance of at least one other person.! WARNING
1987-1995 Jeep Wrangler YJ Hardtop with Half Doors Installation Instructions PLEASE READ CAREFULLY BEFORE STARTING INSTALLATION To safely lift and install this hardtop, you will need the assistance of
More informationService Manual. Bolens 683 Series Box Frame Tractor IMPORTANT: READ SAFETY RULES AND INSTRUCTIONS CAREFULLY
Service Manual Bolens 683 Series Box Frame Tractor IMPORTANT: READ SAFETY RULES AND INSTRUCTIONS CAREFULLY This Service Manual is not a substitute for the Operator s Manual. You must read, understand and
More informationAssembly Manual. 1/10th Formula 1 Car
Assembly Manual 1/10th Formula 1 Car Center Pivot Bag 1 3374 - Center Pivot Socket 40194 - Hard Anodized Alum Pivot ball 3254-2-56 *Note - Sometimes it is helpful to slightly over-tighten the top clamp
More informationINSTALLATION INSTRUCTIONS
Rear Vision System Tailgate Emblem Camera Mirror Display 2009-Current Ford F-150 and 2010-Current Super Duty (Kit part number 1008-9527) Kit Contents: Mirror Tailgate Emblem Mount with Camera Interior
More informationBMW Z4 - By: Eigenes Bild (CC-BY-SA)
Instructions to transfer the hydro pump on a BMW Z4 (E85) to the trunk (AKA boot) and replace the hydraulic hinges and hydraulic hoses if necessary. Graciously provided by Chuck B in Illinois. BMW Z4 -
More informationCold Air Intake Installation Instructions
Page 1/5 3.04 INS262 BAVARIAN AUTOSPORT Cold Air Intake Installation Instructions NOTE: Throughout the instructions the term AFM is used. It refers to the Air Flow Meter which is located between the engine
More informationThe H-MAC Heavy Metal Articulating Chassis Construction Guide
The H-MAC Heavy Metal Articulating Chassis Construction Guide The Heavy Metal Chassis is constructed with two identical drive modules built using 10 mechanical sub-assemblies. The drive modules are integrated
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Accessory Application Publications No. 2004 S2000 AII 26323-31611 Issue Date DEC 2005 PARTS LIST Rear defroster switch Hardtop 3-Pin subharness (If equipped, not used) 4-Pin subharness
More informationpg 2 Disassembly, Wire and Amplifier Plate Installation pg 9 Glovebox Subwoofer Installation pg 13 Kick Panel Speakers Installation
RZ3-5KRC RZR XP1000 & 2015+ RZR900 with Ride Command SSV Works 5 Speaker Audio Kit pg 2 Disassembly, Wire and Amplifier Plate Installation pg 9 Glovebox Subwoofer Installation pg 13 Kick Panel Speakers
More informationCurrent Range Rover Sport STRUT Collection Installation Manual
2014 - Current Range Rover Sport STRUT Collection Installation Manual 1 1. Removing Main Grille and Lower Fascia 1.1 Run a line of low tack masking tape across the front of the bumper below the grille
More informationINSTALLATION INSTRUCTIONS
Rear Vision System Tailgate Handle Camera Mirror Display 2004-2014 Ford F-150 and 2008-2015 Ford Super Duty (Kit part numbers 9002-9521) Kit Contents: Mirror Tailgate Handle with camera and harness Interior
More informationInstallation Instructions Table of Contents
Installation Instructions Table of Contents Pre- Installation of Garage Storage Lift 2 Layout the Garage Storage Lift 3 Installing the strut Channels 3 Install the Drive Assembly 5 Install the Drive Shaft
More informationHub Stands -- VERSION 5.0
Hub Stands -- VERSION 5.0 Thanks for choosing our Alignment Hub Stands for your chassis setup needs. We hope you'll find them as handy, accurate, and easy to use as we do! Each stand has a max capacity
More informationQ15P. Mitsubishi MQ Triton Dual Cab
Mitsubishi MQ Triton Dual Cab Page 1 of 12 Fitting Instructions Part Number Mitsubishi MQ Triton Dual Cab 2015+ To suit Sports Bars Check contents of kit before commencing fitment and report any discrepancies
More informationZ1 Motorsports 350Z / G35 Oil Cooler Kit Installation Manual
Z1 Motorsports 2877 Carrollton Villa Rica Hwy Carrollton GA 30116 770.838.7777 Z1 Motorsports 350Z / G35 Oil Cooler Kit Installation Manual For 19, 25 and 34 Row Oil Cooler Kits Parts Included: 1 Aluminum
More informationBilge Pump Service Project Model Service Kit
Bilge Pump Service Project Model 37202-0000 Service Kit 37182-0000 Boat: 1997 Catalina 320 PAR Electric Bilge Pump 12 volt DC 4.5 GPM 8.0 Amps Prepared by: Ted Harrison History: - Just before haul out
More informationYour G3 buggy is fitted with three switches on the front part of the body:
CONTENTS Buggy operation... 3 General Maintenance... 5 Technical Maintenance... 6 Front wheel bearing replacement... 6 Rear wheel bearing replacement... 7 Chain replacement... 8 Chain Adjustment... 9 Brake
More informationThe HMC-Lite Construction Guide
The HMC-Lite Construction Guide The Heavy Metal-Lite Chassis is constructed using two identical drive modules. The drive modules are constructed using 3 mechanical sub-assemblies. The drive modules are
More informationDARMAN. ENDURA II Cloth Towel Cabinet Product Guide. Manufacturing Company, Inc Lincoln Ave., Utica, NY 13502
ENDURA II Cloth Towel Cabinet Product Guide Page 2, 3 4, 5 6, 7 8, 9 10 11 12 Parts Covered Hood Assembly Mechanism Back Assembly Bin and Towel Guide Service Bulletin - Roller Warranty and Maintenance
More informationIllustrated Parts & Packing List 815 Rice Lake Street, Owatonna, MN 55060
Illustrated Parts & Packing List 815 Rice Lake Street, Owatonna, MN 55060 Great Plains Part # 891-653C (Gandy Part #62270) Mount & Deflector Package For Great Plains Turbo-Max 24/30 Ft Models 2400 (24-Ft)
More informationH15P. Toyota Hilux A-DECK Dual Cab
Toyota Hilux A-DECK Dual Cab Page 1 of 14 Fitting Instructions Part Number H15 Toyota Hilux A-DECK Dual Cab 2015+ To suit Sports Bars Check contents of kit before commencing fitment and report any discrepancies
More informationHayes TrailTrac Kit Installation Guidelines Polaris Rush / Pro-R / Indy
Models: 2010-2014 Polaris Rush / Pro-R / Indy Packing List 1 Electronic Control Unit (ECU) 1 ECU Velcro, 3 inch 1 Switch face plate 1 Switch face plate adhesive 1 Switch 1 Wiring harness 1 Fully pre-filled
More informationSERIES A & AA ROLLER DOORS INSTALLATION GUIDE
SERIES A & AA ROLLER DOORS INSTALLATION GUIDE THESE INSTRUCTIONS ARE PROVIDED FOR USE BY EXPERIENCED INSTALLERS OF GARAGE DOORS BY UNDER-TAKING THE INSTALLATION OF THIS DOOR, THE INSTALLER UNDERSTANDS
More informationLoose Parts Note: Determine the left and right sides of the machine from the normal operating position.
Brake Kit Dingo TX 0 & Compact Utility Loader Part No. 0 0 & 0 Loose Parts Note: Determine the left and right sides of the machine from the normal operating position. Description Qty. Use Drive wheel Brake
More information18SP680Rev3 EPA04 MBE 4000 Car Hauler Low Pressure Fuel Lines
8SP680Rev3 EPA04 MBE 4000 Car Hauler Low Pressure Fuel Lines KIT DESCRIPTION These service kits include all necessary parts to replace the low pressure fuel lines between the fuel filter housing and fuel
More informationD40C HINGE # x Support Plate x M8 Bolt 8 x M8 Washer 6 x M6 20mm Bolts 6 x M6 Washers 19 x Screws
HINGE # 1017 2 x Support Plate 1018 8 x M8 Bolt 8 x M8 Washer 6 x M6 20mm Bolts 6 x M6 Washers 19 x Screws 2 x Lid mount gas strut bracket 1041 2 x Self tap strut mount 1040 1 x Central Lock bracket 1510
More informationSHOP PRO FXP 95 UPGRADE KIT (REGULATED)
1. Make sure the Shop Pro FXP is disconnected from the 120VAC power source. 4. Loosen the five ¼" headed bolts slightly until the motor cover slides to the left and remove the cover. 2. Remove the vent
More information700 Pine Ridge Road Golden CO Tel (303) (888) 4X4 SLEE Fax (303)
700 Pine Ridge Road Golden CO 80403 Tel (303) 278 8287 1(888) 4X4 SLEE Fax (303) 278 7182 Slee Off-Road 1998-07 Land Cruiser / LX470 (* Requires AHC Removal) - Second Instructions Qty Parts Included Suggested
More informationInstallation Instructions for Teraflex 2.5 Inch Lift Kit with Shocks (2010 Jeep Wrangler Unlimited)
Installation Instructions for Teraflex 2.5 Inch Lift Kit with Shocks (2010 Jeep Wrangler Unlimited) Installation Time: 6 Hours Tools Required: Floor Jack Jack Stands Ratchet Torque Wrench 15mm Socket 15mm
More information57-1. Front door. Tools. Special tools and equipment. T Socket 3320/2 Bit insert for Socket T Assembly tool
57-1 Front door Tools Special tools and equipment T 10011 Socket 3320/2 Bit insert for 3320 3410 Socket T 10034 Assembly tool 57-2 Front door, assembly overview Note: The instrument panel must be removed
More informationTC1000 Service Manual SALES: CUSTOMER SERVICE:
TC1000 Service Manual SALES: 800-278-3933 CUSTOMER SERVICE: 800-745-1373 Table of Contents Section Page I. Overview 2 II. Troubleshooting Tables 3 III. Maintenance Procedures Procedure 1 Removal and Reinstallation
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Accessory HARD FRONT DOORS P/N 0SU95-HL4-104 Application SXS1000M3/M3P/M3L/M5D/ M5P/M5L Honda Dealer: Please give a copy of these instructions to your customer. Publication No.
More informationINSTALLATION INSTRUCTIONS
Rear Vision System Tailgate Emblem Camera Aftermarket Display 2009-Current Ford F-150 and 2010-Current Super Duty (Kit part number 1008-6509) Kit Contents: Tailgate Emblem Mount with Camera Chassis Harness
More informationSX1000 Service Manual SALES: CUSTOMER SERVICE:
SX1000 Service Manual SALES: 800-278-3933 CUSTOMER SERVICE: 800-745-1373 Revision: August 1999 Table of Contents Section Page I. Overview 2 II. Troubleshooting Tables 3 III. Maintenance Procedures Procedure
More informationTESLA MODEL S REAR UNDER SPOILER & DIFFUSER SYSTEM
TESLA MODEL S Thank you for purchasing your Unplugged Performance Rear Under Spoiler & Diffuser System for the Tesla Model S! Please read this manual carefully prior to installation. REAR UNDER SPOILER
More informationBase Kit Chain Drivetrain Build Guide
222fg Base Kit Chain Drivetrain Build Guide August 11, 2017 Chain Drivetrain Build Guide Copyright 2017 REV Robotics, LLC 1 1.1 Description This document outlines the steps required to four wheel, chain
More informationDVS Cypress Face Installation Instructions (SKU )
Table of Contents Compatibility... 1 Packing List... 1 Installation... 2 Prepare the Insert for Face Installation... 2 Attach the Surround Panels (if applicable)... 6 Assemble the Face... 7 Attach the
More information5. E-axis assembly. 5. E-axis assembly. Written By: Jakub Dolezal manual.prusa3d.com/ Page 1 of 40
5. E-axis assembly Written By: Jakub Dolezal 2018 manual.prusa3d.com/ Page 1 of 40 Step 1 Tools necessary for this chapter Needle-nose pliers for zip tie trimming. 2.5mm Allen key for M3 screws 2mm Allen
More information3 Axles and brakes. 3.1 Function and construction of the axles Construction Function
3 Axles and brakes 3.1 Function and construction of the axles 3.1.1 Function Each wheel has an independent suspension system in the axle body (1), so that individual wheel suspension is provided. The swinging
More informationFord AOD-4R70W-AODE Cable Operated Shifter Installation Instructions
Ford AOD-4R70W-AODE Cable Operated Shifter Installation Instructions Building American Quality With A Lifetime Warranty! TOLL FREE 1-877-469-7440 tech@lokar.com www.lokar.com Ford AOD-4R70W-AODE Cable
More informationIntroduction Date: October 2007 Pt No INSTRUCTION KIT JOINER RF 1 KIT COMPONENTS
KIT COMPONENTS Part Illustration Rear Bracket Description Front Lower Bracket KIT APPLICATION This kit is designed for use on 1595mm / 62 & 1695mm / 66 high cabinet models, incorporating the B, C, D &
More informationRear Vision System Liftgate Emblem Camera for Aftermarket Display Ford Flex (Kit part number )
Rear Vision System Liftgate Emblem Camera for Aftermarket Display 2009-2012 Ford Flex (Kit part number 1008-6509) Kit Contents: Liftgate Emblem Mount with Camera Chassis Harness with RCA (Note: In some
More informationHow to fold your MGB top (pre 1970 pack away top & frame)
How to fold your MGB top (pre 1970 pack away top & frame) It is most important that the instructions given for raising, lowering and folding the hood are followed. Do not use undue force on the hood frame-members.
More informationFIAT 500 ABARTH FRONT MOUNTED INTERCOOLER INSTALLATION
FIAT 500 ABARTH FRONT MOUNTED INTERCOOLER INSTALLATION Tools needed: T30 screwdriver/bit 10mm socket, suitable extension and ratchet 17mm socket, suitable extension and ratchet 10mm ratchet spanner Pozidriv/Phillips
More informationRZ3-5K Polaris RZR XP 1000 & 900 Kicker 5 Speaker Audio Kit
PO H PWER PO 5 O KIT I E D U A S A TS S I R LA R Z R R O SP pg 2 pg 9 pg 13 pg 25 pg 29 Disassembly, Wire and Amplifier Plate Installation Glovebox Subwoofer Installation Kick Panel Speakers Installation
More informationAssembly & Installa on Guide RB091-3: TRIPLE CROSSBAR KIT
PLEASE READ INSTRUCTIONS FULLY PRIOR TO INSTALLATION OF CROSSBAR KIT This instruction is to illustrate the recommended installation method for our Crossbar Kit, any deviation from this will be the sole
More information*Enclosed pictures and devices are for reference only. Individual vehicles and devices may vary.
Dash Strap Mount Product Number AS5.S500.001 *Enclosed pictures and devices are for reference only. Individual vehicles and devices may vary. The Dash Strap Mount is held tight against the vehicle dash
More informationRZ3-5A Polaris RZR XP 1000 & 900 SSV Works 5 Speaker Audio Kit
RZ3-5A Polaris RZR XP 1000 & 900 SSV Works 5 Speaker Audio Kit pg 2 Disassembly, Wire and Amplifier Plate Installation pg 9 Glovebox Subwoofer Installation pg 13 Kick Panel Speakers Installation pg 25
More informationInstallation Instructions LamboStyleDoors
Installation Instructions LamboStyleDoors (The instruction refers only to one side of the car, but is valid for both sides) Preparations: (Dismantling according to the regulation of the car manufacturer)
More information2008~2010 Polaris RZR 800* Cab Enclosure Kit Slam latch hardware
Owner s Manual Model: Polaris RZR * 2008~2010 Polaris RZR 800* Cab Enclosure Kit Slam latch hardware Caution: Before using this product, read this manual and follow all safety instructions. Safety Instructions
More informationInstallation Instructions LamboStyleDoors
Installation Instructions LamboStyleDoors (The instruction refers only to one side of the car, but is valid for both sides) Preparations: (Dismantling according to the regulation of the car manufacturer)
More informationRear Vision System Tailgate Emblem Camera Aftermarket Display 2009-Current Ford F-150 and 2010-Current Super Duty (Kit part number )
Rear Vision System Tailgate Emblem Camera Aftermarket Display 2009-Current Ford F-150 and 2010-Current Super Duty (Kit part number 1008-6509) Kit Contents: Tailgate Emblem Mount with Camera Chassis Harness
More informationITEM QTY CHECK PART NUMBER DESCRIPTION
PART #21128 2010 Camaro Cold Air Induction Stage II PACKING LIST Before installation, use this check list to make sure all necessary parts have been included. ITEM QTY CHECK PART NUMBER DESCRIPTION 1.
More informationPart Numbers: TTU-BGP14 & TTU-BGB14
Date: 10.14.2015 TOYOTA TUNDRA 2014-17 Billet Grille Part Numbers: TTU-BGP14 & TTU-BGB14 Grille Hardware Bag Contents Item # Quantity. Description 1 6 U-Nuts 2 8 #10 Screws 3 2 #8 Screws 4 2 2 Flange Brackets
More informationZeiss ZAT Cube Assembly Procedure
1.1.1 The ZAT cube assembly has two filter retainer rings; one is located on the Exciter side and one is on the Emitter side as shown below. Note that the Exciter housing is marked with a red dot and the
More informationLOW, MID, HIGH RISE PRO-TAPER HANDLEBAR WITH HEATED GRIPS KIT
LOW, MID, HIGH RISE PRO-TAPER HANDLEBAR WITH HEATED GRIPS KIT P/N 2881235; 2881236; 2881237 APPLICATION All AXYS and PRO RIDE chassis with stock Pro-Taper Bar BEFORE YOU BEGIN Read these instructions and
More information2006 Toyota Truck Tundra 4WD V8-4.7L (2UZ-FE)
ALLDATA Repair - 2006 Toyota Truck Tundra 4WD V8-4.7L (2UZ-FE) - Service and R... Page 1 of 12 2006 Toyota Truck Tundra 4WD V8-4.7L (2UZ-FE) Vehicle» Powertrain Management» Fuel Delivery and Air Induction»
More informationBlue Sky Sun Visors. RV-10 Installation Instructions. - Portable drill - 9/64 drill bit - 5/64 drill bit
Blue Sky Sun Visors RV-10 Installation Instructions Tools needed: - Portable drill - 9/64 drill bit - 5/64 drill bit - 100 Degree Countersink Bit - Phillips #2 Screwdriver - Measuring tape - Pencil Step
More informationJ2 Remove sound insulation/knee guard 1 and side panel 2 on center console
J1 Preparations Drive car forward on a level surface so that wheels are straight. Disconnect battery negative lead. Turn ignition key to position 1 so that steering lock is off. J2 Remove sound insulation/knee
More information<THESE INSTRUCTIONS MUST BE GIVEN TO THE END USER> B&W Trailer Hitches 1216 Hawaii Road / PO Box 186 Humboldt, KS P: F:
B&W Trailer Hitches 26 Hawaii Road / PO Box 86 Humboldt, KS 6678 P:620.73.366 F:620.869.903 RAM OEM Mount System Installation Instructions 25,000 LBS.
More informationINSTALLATION INSTRUCTIONS
INSTRUCTIONS Accessory Application Publications No. SIDE 2008 CIVIC 4-DOOR All 37741 Issue Date AUG 2007 PARTS LIST Left side under spoiler Right side under spoiler 2 Side lower brackets The side lower
More informationalong with standard XT2 Instruction Manual and also XT2 18 Supplementary Sheet.
Use this XT2 Dirt Conversion Supplementary Sheet along with standard XT2 Instruction Manual and also XT2 18 Supplementary Sheet. Parts included in Bag 8: 303141 SHIM 3x5x1.0MM (10) 322111 XT2 COMPOSITE
More informationREMOVAL & INSTALLATION
REMOVAL & INSTALLATION NOTE: For reassembly reference, label all electrical connectors, vacuum hoses and fuel lines before removal. Also place mating marks on engine hood and other major assemblies before
More informationWood Grain Warrior Line Incognito hidden winch bumper installation instructions Lexus GX470
Wood Grain Warrior Line Incognito hidden winch bumper installation instructions 2003-2009 Lexus GX470 Version 1.0-2016 Thank you for purchasing the Southern Style OffRoad Wood Grain Warrior Line Lexus
More informationAirtail I.A.S. Suspension System for Harley Davidson
5572 Fresca Drive, La Palma, CA 90623 714.523.8700, FAX 714.523.3220 Airtail I.A.S. Suspension System for Harley Davidson Compressor Kit Installation Instructions FLH/FLT Models with and without Cruise
More informationReplacement Cluster Fascia Replacement
1 of 12 11/1/2013 9:13 AM SOUL(AM) >2010 > G 2.0 DOHC > Body (Interior and Exterior) Replacement Cluster Fascia Replacement When prying with a flat-tip screwdriver, wrap it with protective tape, and apply
More informationMMR20. Instruction Manual for Operation & Maintenance. IB International. Ph:
MMR20 Instruction Manual for Operation & Maintenance IB International www.ibinternational.com.au Ph: 07 3399 1288 Contents Introduction... 2 Identification Data... 2 Machine Controls & Components... 3
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS IMPORTANT Before opening your Lights.com fixture, please make sure that you carefully read through these instruction sheets. Consider having your fixture installed by a qualified
More informationINSTALLATION GUIDE TCP RCKM-01
READ ALL INSTRUCTIONS COMPLETELY AND THOROUGHLY UNDERSTAND THEM BEFORE DOING ANYTHING. CALL TOTAL CONTROL PRODUCTS TECH SUPPORT (916) 388-0288 IF YOU NEED ASSISTANCE. INSTALLATION GUIDE TCP RCKM-01 Manual
More informationSUSPENSION 2-1 SUSPENSION TABLE OF CONTENTS
DN SUSPENSION 2-1 SUSPENSION TABLE OF CONTENTS page ALIGNMENT... 1 FRONT SUSPENSION - 4x2... 6 page FRONT SUSPENSION - 4x4... 14 REAR SUSPENSION... 23 ALIGNMENT TABLE OF CONTENTS page AND OPERATION WHEEL
More informationInstallation Instructions Right Hand Drive Megashifter
Installation Instructions Right Hand Drive Megashifter Part Number 80685 1995, 2001, 2006, 2010 by B&M Racing & Performance Products The B&M Right Hand Drive Megashifter is designed specifically for vehicles
More informationFiber optic splice closure
FOSC-450A I N S T A L L A T I O N I N S T R U C T I O N TC-772-IP Rev A, Mar 2017 www.commscope.com Fiber optic splice closure Content 1 Introduction 2 General 2.1 Kit content 2.2 Tools 2.3 Accessories
More information2 Rubber Bumper GSM MM nut GSM30201 K9-F18-PT_INST_4-16
K9-F18-PT INSTALLATION INSTRUCTIONS K9 Kit for 2013-2019 FORD INTERCEPTOR UTILITY Vehicle Notes: 1. For K9 applications, it is recommended to order the Interceptor Utility with the OEM optional Aux Rear
More informationINSTALLATION INSTRUCTIONS
COLD AIR INTAKE INSTALLATION INSTRUCTIONS PART NUMBER D760-0620 & D760-0621 PARTS LIST APPLICATION: 9/98-2003 E39 540i 4.4L 4" Intake Tube Air Filter w/ clamp Silicone Hose 80-100mm Hose Clamp 90-110mm
More informationAdult Car Plans. A comprehensive guide to help you build an official Soap Box Derby Adult Car
Adult Car Plans A comprehensive guide to help you build an official Soap Box Derby Adult Car 1 Table Of Contents Introduction...Page 3 Adult Car Floorboard...Page 4 Step One Steering Stop Installation...Page
More informationInstallation Guide Current Ford F-250 & Ford F-350 Super Duty. Product Code: 109 & 119
Installation Guide 2008 - Current Ford F-250 & Ford F-350 Super Duty Product Code: 109 & 119 September 1, 2012 Tools Needed Components Included 3/8" Drill P2 Tip #2 Philips Screwdriver 1/2" Drill Bit Hinged
More informationJEEP WRANGLER. Front Door/Hardtop Storage System* * Storage Caddy Holds two (2) Front Doors Only with two (2) Sun Top Panels and No Rear Doors
JEEP WRNGLER Front Door/Hardtop Storage System* 5X * Storage addy Holds two (2) Front Doors Only with two (2) Sun Top Panels and No Rear Doors 05-18-06 65038 1 of 11 K6860080 K6860080 Top art Door art
More informationCOBB Tuning Catback Exhaust System MAZDASPEED3
572101 COBB Tuning Catback Exhaust System 2010+ MAZDASPEED3 Congratulations on your purchase of the COBB Tuning SS Catback Exhaust System for your 2010+ MAZDASPEED3. The following instructions will assist
More informationGT-R Alpha 10/12 Turbo Kit
GT-R Alpha 10/12 Turbo Kit Instructions V6 The goal of AMS is to provide the highest quality, best performing products available. By utilizing research and development, and rigorous testing programs AMS
More informationBag 1. Bag 1. Center Pivot. Center Pivot
8 00734 01901 5 Center Pivot Bag 1 3374 - Center Pivot Socket 4019 - Alum Pivot ball 3254-2-56 Button Head *Note - Sometimes it is helpful to slightly over-tighten the top clamp screws, then work the ball
More informationChevy Nova Pro-Touring Front Suspension Installation Instructions
1962-1967 Chevy Nova Pro-Touring Front Suspension Installation Instructions 1-800-984-6259 www.totalcostinvolved.com 1 Pro-Touring Clip A-Arm Assembly Sway Bar Assembly Fender Panel Kit 8 7/16-20 * 1 ¼
More informationFlue Space Installation Instructions
Flue Space Installation Instructions Required Tools 1. 2. 4. 3. 3a. 5. 6. 8. 7. 9a. 7a. 9b. 7b. 9c. KEY 1. Philips Screw Driver 2. Crescent Wrench 3. 3/8 Socket Wrench a. 7/16 Socket (~11 mm) 4. 2 Ladders
More informationPost-Paint>Fuselage>Assemble instrument panel. Objectives of this task: Materials and tools required: Prepare the work area
Post-Paint>Fuselage>Assemble instrument panel Objectives of this task: To fit all instruments into the instrument panel, fit all of the electrical wiring and terminate to multi-pin connectors ready for
More informationWildcat System Instructions
Wildcat System Instructions NOTE: Most steps contained in these instructions will need to be repeated on the other side of the vehicle. Prior to assembly of windshield it is necessary to establish what
More informationSkyline 4 Fascia Fabrication & Installation Instructions
Components Needed Page 2 Tools Needed Page 2 System Diagram Page 3 Instructions Step 1: Install Brackets Page 4 Step 2: Install Pre-assembled Shade Page 4 Step 3: Install Fascia Clip Page 4 Step 4: Cut
More informationDisconnect the APP sensor harness connector. See Fig. 4. Remove the accelerator pedal mounting nuts. Remove the APP assembly.
ENGINE CONTROLS - REMOVAL, OVERHAUL & INSTALLATION - 6.6L DIESEL... Page 1 of 41 FUEL SYSTEMS ACCELERATOR PEDAL POSITION SENSOR Removal & Installation Disconnect the APP sensor harness connector. See Fig.
More informationINSTALLING THE NEUTRAL SAFETY SWITCH WIRES
Installation Instructions Magnum Grip Pro Bandit Shifter Part Number 81045 & 81046 2004, 2003 by B&M Racing and Performance Products (Visit www.bmracing.com for additional products and product information)
More informationFRONT FENDERS WITH FACTORY INNER FENDERS JEEP WRANGLER TJ/LJ/YJ/CJ7 INSTALLATION INSTRUCTIONS
FRONT FENDERS WITH FACTORY INNER FENDERS JEEP WRANGLER TJ/LJ/YJ/CJ7 INSTALLATION INSTRUCTIONS TOOLS NEEDED 13mm socket 5/32 Allen head 5/16 wrench or socket 7/16 wrench or socket 7/32 Allen head 5/8 wrench
More informationBAG 3 (2) 2.25 x 1 Sleeves (4) 1/4 Nylock Nuts (4) 1/4 x 2 Bolts (4) 3/8 Nylock Nuts (4) 3/8 Flat Washers (2) 3/8 U-Bolts
INSTALLATION INSTRUCTIONS PART # DESCRIPTION 799 Lincoln Ave. Riverside, CA 90 Phone: 9.689.ICON Fax: 9.689.06 90 00+ RAPTOR REAR BUMPSTOP SYSTEM ** READ ALL INSTRUCTIONS THOROUGHLY FROM START TO FINISH
More informationINSTALLATION GUIDE P1000 PRO-CELL CURRENT FORD POLICE UTILITY INTERCEPTOR. pro-gard.com STRONG RELIABLE SECURE
INSTALLATION GUIDE P1000 PRO-CELL 2013 - CURRENT FORD POLICE UTILITY INTERCEPTOR STRONG RELIABLE SECURE THESE COMPONENTS ARE REQUIRED TO INSTALL THE PRO-GARD PARTITION SYSTEM WB4711-01D WB4711-01P 4K47UINTPRO
More information2011-up Polaris RZR 800* Cab Enclosure Kit. Caution: Before using this product, read this manual and follow all safety instructions.
Owner s Manual Model: Polaris RZR * 2011-up Polaris RZR 800* Cab Enclosure Kit Caution: Before using this product, read this manual and follow all safety instructions. Safety Instructions Kit Contents
More information