PRODUCT CATALOG. Powered by ELECTRONET

Transcription

1 PRODUCT CATALOG

2 Flow Meters

3 Magnetic Flow Meters

4 ELMAG- 60H ELECTRO NET MAGNETIC FLOW METER ELMAG 60H DESCRIPTION The ELMAG-60H is a micro-controller based 2 wire full bore type electromagnetic flow transmitters specially used for various industrial applications. These flow transmitters accurately measure the flow rate of conductive liquids & slurries in closed pipes. Due to its simple & rigid design, the flow transmitter is an obstruction- less & maintenancefree instrument in place of conventional mechanical flow measuring device. The use of Pulsed DC technology offers highest ability & better measuring accuracy in the form of electrical signal 4-20 ma DC inearly proportional to volumetric flow, The instrument is based on Faraday s law of electromagnetic induction. A magnetic field is generated by the instrument in the flow tube. The fluid flowing through this magnetic field generates a voltage that is proportional to the flow velocity & corresponding electrical output is provided with respect to easuring voltage. SALIENT FEATURES Full bore type Suitable for conductive liquids 2 wire system with HART communication Material option depending upon process data Empty pipe indication Local Indication through Graphics LCD Maintenance free Simple & cost effective construction Inbuilt Data Logger DIMENSIONAL DETAILS FD Fig. Front View Line Size Flange Diameter D Diameter of Raised Face R Diameter of Bolt Hole Circle DBC Diameter of Bolt Hole No. of Holes Flange Distance FD Flow Range(m 3 /hr) at 0.03m/s to 6m/s Inch NB Minimum Maximum ½ / ½ ½ R Ø DBC Lining Ø Bolt Hole Note For Line size above 600NB consult factory. Typical mounting dimensions for reference. Standard factory calibration for 0.2 to 2 m/s velocity. Flow meter should be selected with the help of Nomograph recommended full scale velocity. Flow indication of 5 digit max. up to D 1 Fig. Side View

5 MAGNETIC FLOW METER ELMAG 60H TECHNICAL SPECIFICATIONS Media Conductivity Viscosity Line Size Excitation Type of Output Display Calibration Range Accuracy Linearity Repeatability Temperature Coefficient Process Temperature Process Pressure Material of construction Power Supply Power Consumption Response Time Electronics Transmitter Enclosure Process Connections Mounting Operating Conditions Liquids (Conductive) > 5 µs/cm 200 cp max 15 NB to 600 NB Pulsed DC coil 4 to 20mA DC, 2 wire HART COG Graphic LCD display - 5 digit for Flow Rate & 8 digit for Totalizer Flow As per requirement (Factory Calibrated for std. 2m/s velocity) +/- 0.5% M.V.(For 20 to 100% flow) +/- 0.5% of M.V. +/- 0.2% of M.V. +/- 0.1% per C 85 C max for Rubber Lining & 220 C for PTFE Lining 10 kg/cm² max (higher on request) Lining - Neoprene Rubber / Hard Rubber / EPDM / PFA / PTFE Flange - MS / CS / SS316 Electrode - SS 316L/ Hastalloy C / Platinum / Tantalum Coil Housing - MS / SS 304 / SS V DC < 40mW <10 Sec Integral / Remote Electronics IP66, Flow Tube IP68 ASA150 flanged, as per table B 16.5 (Other On Requirement) In-Line Horizontal / Vertical Temperature -20 to 75 C / Humidity 5 to 95% non condensing Note - For process conditions other than above please consult factory. ORDERING INFORMATION 15NB To 600NB 08 Other 05 PTFE 02 Remote 02 SS Hard Rubber 01 Local 01 Aluminum 01 Neoprene Rubber Lining Enclosure Material 04 PFA 04 Tantalum 03 EPDM 03 Platinum 02 SS Other 02 SS Hyst. C mA + HART 09 10mtr 01 MS / CS 01 ASA MS 01 SS 316L mA 01 5mtr Series Line Size Electronics Electronic Flange Flange Coil Electrode Output Remote Material Rating Housing Material Cable Length ELMAG 60H A 15NB B 01 C 01 D 01 E 01 F 01 G 01 H 01 I 01 J 01 * Due to our continuous product improvisations, Design, Specifications and Model Number are subject to change without notice. * GSM output is without SIM card & SCADA viewing software. * For better accuracy consult factory. * Accuracy defined at lab conditions. 2

6 INSERTION TYPE ELECTROMAGNETIC FLOW METER ELMAG-100 SALIENT FEATURES Suitable for conductive liquid Maintenance free Insertion Type Local Indication through LCD Simple & cost effective construction Unit conversion facility Material option depending upon process data Universal Power Supply 90 to 260V AC Optional 24V DC Communication port (Optional) DESCRIPTION The ELMAG-100 is a micro-controller based full bore type electromagnetic flow meters specially used for various industrial applications. These flow meters accurately measures the flow rate of conductive liquid & slurries in closed pipes. Due to simple & rigid design, the flow meter is an obstruction less & maintenance free instrument in place of conventional mechanical flow measuring device.the use of Pulsed DC technology offers highest ability & better measuring accuracy in the form of electrical signal 4-20mA DC linearly proportional to volumetric flow. The instrument is based on Faraday s law of electro-magnetic induction. A magnetic field is generated by the instrument in the flow tube. The fluid following through this magnetic field generates a voltage that is proportional to the flow velocity. Corresponding electrical output is provided with respect to measuring flow range. TECHNICAL SPECIFICATIONS Media Conductivity Viscosity Line Size Excitation Type of Output Display Calibration Range Accuracy Linearity Repeatability Process Temperature Process Pressure Material of construction Power Supply Power Consumption Response Time Temperature Coef cient Process Connections Mounting Operating Conditions Transmitter Enclosure Liquids (Conductive) > 5 µs/cm 200 cp max 200 NB to 2000 NB Pulsed DC 1) 4 to 20 ma DC 2) Pulse 16 x 2 LCD - 4 digit for Flow Rate & 8 digit for Totalised Flow As per requirement (Factory Calibrated up to 4NB) +/- 2% of F. S. (for 20 to 100% ow) +/- 0.5% of F. S. +/- 1% of F. S. 85 ºC max. 10 kg/cm 2 max Electrode - SS 316L Retractable Assembly - MS / SS 304 Wetted Parts - SS 316 Option 1 24 V DC Option V AC, 50 Hz < 10 VA < 1 Sec +/- 0.01% per ºC ASA 150, 2 Flanged, as per table B 16.5 Insertion type Temperature 0 to 55 ºC / Humidity 5 to 95% non condensing Die Cast Aluminium IP 68 3 OPTIONAL Communication Port Remote Electronics RS 485 supporting MODBUS RTU Protocol GSM connectivity Weather-proof, IP-65, wall mounted

7 ELECTROMAGNETIC FLOW METER ELMAG-200E INSERTION TYPE ELECTROMAGNETIC FLOW METER ELMAG-100 DIMENSIONAL DETAILS M20 x 1.5,DOUBLE COMPRESSION CABLE ENTRY 120 mm 90 mm Adjustable 1000mm 290mm 5 mm GASKET NEOPRENE 100mm 200 mm P P ELMAG- 100 CMRI CERTIFIED DIE CAST ALUMINIUM FLAMEPROOF HOUSING 2 SS FLANGE ASA 150 B mm 15 mm 120 mm 26.5 mm 2 SS FLANGE ASA 150 B mm 49 mm 1&1/2 Ball Valve 2 SS FLANGE ASA 150 B mm 47mm Line Size (mm) Flow min (m/ 3 hr) Flow normal (m/ 3 hr) Flow max (m/ 3 hr) Flow (MLD) FLOW INLET Line Size/ mm LINE SIZE 200NB to 2000NB FLOW OUTLET Note Typical mounting dimensions for reference Standard factory calibration for 0 to 2m/Sec velocity ORDERING INFORMATION 200 mm to 2000 mm 04 All mA 09 None mtr. + HART Pulse R Remote 02 SS V AC 03 GSM mtr. 09 None 02 SS mA L Local 01 Aluminium ma 01 24V DC 02 RS mtr. 01 Data logger 01 MS SERIES Line Size Electronics Electronics Enclosure Output Power Supply Communication Port Remote Cable Length Data Logging Retractable Sensor Assembly ELMAG mm L / R E 01 F 01 G 02 H 02 I 02 J 01 K 02 *Due to our continuous product revisions, Design, Speci cations and Model Number are subject to change without notice. *Accuracy de ned at lab conditions. Note GSM output is without SIM card & SCADA viewing software. 4

8 EL E M LM A A G G MH ELEECLETCRTORMOAMGAGNNEETTICC FLOOWWMMETEETRER NO ELECTROMAGNETIC FLOW METER ELMAG 200 SALIENT FEATURES Suitable for conductive liquids Maintenance free Full bore type Local Indication through LCD Simple & cost effective construction Empty pipe indication Material option depending upon process data Universal Power Supply 90 to 260V AC Optional 24V DC Communication port (Optional) HART Communication DESCRIPTION The ELMAG-200 is a micro-controller based full bore type electromagnetic flow meters specially used for various industrial applications. These flow meters accurately measures the flow rate of conductive liquid & slurries in closed pipes. Due to simple & rigid design, the flow meter is an obstruction less & maintenance free instrument in place of conventional mechanical flow measuring device. The use of Pulsed DC technology offers highest ability & better measuring accuracy in the form of electrical signal 4-20mA DC linearly proportional to volumetric flow. The instrument is based on Faraday s law of electro-magnetic induction. A magnetic field is generated by the instrument in the flow tube. The fluid following through this magnetic field generates a voltage that is proportional to the flow velocity. Corresponding electrical output is provided with respect to measuring flow range. DIMENSIONAL DETAILS 250 mm H P P MODE L SR. W FD Meter OD W H FD Flow Range (m³ /hr) Size (mm) (mm) (mm) (mm) Min Normal Max 15 NB NB NB NB NB NB NB NB NB NB NB NB NB NB NB NB NB NB NB OD Flange Diameter H Coil Housing Height W Coil Housing width FD Flange to Flange distance 5 OD

9 ELECTROMAGNETIC FLOW METER ELMAG 200 TECHNICAL SPECIFICATIONS Media Conductivity Viscosity Line Size Excitation Type of Output Display Engineering Unit Calibration Range Accuracy Linearity Repeatability Temperature Coef cient Process Temperature Process Pressure Material of construction Power Supply Power Consumption Isolation Response Time Transmitter Enclosure Process Connections Mounting Operating Conditions Liquids (Conductive) > 5 µs/cm 200 cp max 15 NB to 600 NB Pulsed DC 1) 4 to 20 ma DC, Isolated, HART 2) Pulse 16 x 2 LCD - 4 digit for Flow Rate & 8 digit for Totalised Flow User Programmable (m³ /hr by default) As per requirement (Factory Calibrated for std. 2m/s velocity) +/- 0.5% of F. S. (for 20 to 100% ow) +/- 0.5% of F. S. +/- 0.2% of F. S. +/- 0.05% per C 85 C max for Rubber Lining & 120 C for PTFE Lining 10 kg/cm² max (higher on request) Lining - Rubber (5mm +/-1mm thick) / PTFE (Te on) (3mm +/-1mm thick) Flange - CS / MS / SS Electrode - SS 316L / Hastalloy C / Platinum Coil Housing - MS / SS 304 Option 1 24 V DC Option V AC, 50 Hz < 10 VA 1.4 KV between Input, Output & Power Supply < 1 Sec Die cast Aluminium IP 66, ow tube IP 68 ASA 150 anged, as per table B 16.5 In-Line Horizontal (Vertical on request) Temperature 0 to 55 C / Humidity 5 to 95% non condensing Note - For process conditions other than above please consult factory. OPTIONAL Communication Port 1) RS 485 supporting MODBUS RTU Protocol 2) GSM Communication 3) 4-20mA with HART Electronics Remote Electronics ORDERING INFORMATION 08 Other 04 All 4-20mA 08 Other 03 SS SS Platinum 03 + HART 09 None mtr. 15 mm to R Remote 02 Rubber L 4-20mA 02 SS SS Hyst C 02 SS Pulse V AC 02 GSM mtr. 600 mm Local 01 PTFE 01 CS / MS 01 MS 01 SS 316L 01 Aluminium ma 01 24V DC 01 RS mtr. SERIES Line Size Electronics Lining Flange Coil Electrode Electronics Power Output Communi- Remote Material Housing Material Enclosure Supply cation Port Cable Length ELMAG mm L / R A 02 B 01 C 01 D 01 E 01 F 01 G 02 H 01 I None 01 Datalogger Data logging J 02 6 *Due to our continuous product revisions, Design, Speci cations and Model Number are subject to change without notice. *Accuracy de ned at lab conditions. Note GSM output is without SIM card & SCADA viewing software. Consult Factory

10 BATTERY POWERED ELECTROMAGNETIC FLOW METER ELMAG-600 SALIENT FEATURES Full bore type Suitable for conductive liquid Battery Operated Data Logging facility for 5 Years Local Indication through Graphics LCD Communication port (Optional) Empty pipe indication(optional) Maintenance free Simple & cost effective construction Inbuilt Data Logger DESCRIPTION The ELMAG-600, is a battery-powered Electromagnetic flow meters are ideal when connecting to a power is difficult or expensive. When no mains power is available, the battery powered ELMAG-600 gives the flexibility to install a reliable flow meter, virtually anywhere, without distorting accuracy & performance. ELMAG-600 is provided with 2 years continuous battery operation. The flow meter is extremely easy to use, simple to install & requires no regular maintenance. The product is engineered for various industrial as well as domestic applications such as Municipal & Industrial Water applications, Cooling tower, Water treatment, etc. The graphic display provides indication for flow rate & totalized flow with key selection. The display auto shuts off after 10 minutes, which saves the battery life. The display can be turned ON by pressing the 'enter' key. 7 TECHNICAL SPECIFICATIONS Media Conductivity Viscosity Line Size Excitation Display Calibration Range Accuracy Linearity Repeatability Temperature Coefficient Process Temperature Process Pressure Material of construction Power Supply Low Bat indication Battery Life Response Time Transmitter Enclosure Process Connections Mounting Operating Conditions Data Logging Liquids (Conductive) > 5 µs/cm 200 cp max 15 NB to 600 NB Pulsed DC COG Graphic LCD display- 5 digit for Flow Rate & 8 digit for Totalizer Flow As per requirement (Factory Calibrated ) +/- 0.5% of M.V. (for 20 to 100% flow) +/- 0.5% of M.V. +/- 0.2% of M.V. +/- 0.05% per C 85 C max for Rubber Lining & 220 C for PTFE Lining 10 kg/cm² max (higher on request) Lining - Neoprene Rubber / Hard Rubber / EPDM / PFA / PTFE Flange - MS /CS / S316 Electrode - SS 316L/ Hastalloy C / Platinum / Tantalum Coil Housing - MS / SS 316 Inbuilt Battery 3.6 V, 19 Ah ( 2 nos) Provided 2 to 10 years depending on sampling time. <10 Sec Electronics IP66, Flow Tube IP68 ASA150 flanged, as per table B 16.5 (Other On Requirement) In-Line Horizontal / Vertical Temperature -20 to 75 C / Humidity 5 to 95% non condensing For 5 years (per day 1 sample) Note - For process conditions other than above please consult factory. OPTIONAL Communication Output 1) RS 232 2) GSM connectivity 3) Pulse

11 ELMAG 600 BATTERY POWERED ELECTROMAGNETIC FLOW METER ELMAG-600 DIMENSIONAL DETAILS R FD Fig. Front View D Fig. Side View ½ / ½ ½ Ø Bolt Hole Ø DBC Lining DIMENSIONAL DETAILS OF FLANGE(AS PER ASA150 # B-16.5) Line Size Flange Diameter D Diameter of Raised Face R Diameter of Bolt Hole Circle DBC Diameter of Bolt Hole No. of Holes Flange Distance FD Note For Line size above 600NB consult factory. Typical mounting dimensions for reference. Standard factory calibration for 0.2 to 2 m/s velocity. Flow meter should be selected with the help of Nomograph recommended full scale velocity. Flow indication of 5 digit max. up to Flow Range(m 3 /hr) at 0.03m/s to 6m/s Inch NB Minimum Maximum Measuring error (% M.V) Flow Nomograph 1.0% 0.9% 0.8% 0.7% 0.6% 0.5% 0.4% 0.3% 0.2% 0.1% 0.0% Flow Velocity 6 m/s ORDERING INFORMATION 08 Other 05 PTFE 04 PFA 04 Tantalum 15NB To 600NB 02 Remote 02 SS Hard Rubber 01 Local 01 Aluminum 01 Neoprene Rubber Lining Enclosure Material 03 EPDM 03 Platinum 03 Pulse 02 SS Other 02 SS Hyst. C 02 GSM 02 10mtr 01 MS /CS 01 ASA MS 01 SS 316L 01 RS mtr Series Line Size Electronics Electronic Flange Flange Coil Electrode Comm. Material Rating Housing Material Output ELMAG 600 A 150NB B 01 C 01 D 01 E 01 F 01 G 01 H 01 I 01 J 01 Remote Cable Length * Due to our continuous product improvisations, Design, Specifications and Model Number are subject to change without notice. * GSM output is without SIM card & SCADA viewing software. * For better accuracy consult factory. * Accuracy defined at lab conditions. 8

12 ELECTRONIC WATER METER ELMAG-600W SALIENT FEATURES Electronic replacement to mechanical water meter Battery Powered Real time data Reliable connectivity Durability Accurate measurement Zero maintenance Tampering protection Low pressure loss Simple installation Simple & cost effective construction DESCRIPTION The ELMAG-600W, battery-powered Electromagnetic water meters, are ideal when connecting to a power is difficult or expensive. When no mains power is available, the battery powered ELMAG-600W gives the flexibility to install a reliable flow meter, virtually anywhere, without distorting accuracy & performance. ELMAG-600W is provided with 2 years continuous battery operation. The water meter is extremely easy to use, simple to install & requires no regular maintenance. The product is engineered for various industrial as well as domestic applications such as Municipal & Industrial Water applications, Cooling tower, Water treatment, etc. The graphic display provides indication for flow rate & totalized flow with key selection. The display auto shuts off after 10 minutes, which saves the battery life. The display can be turned ON by pressing the 'enter' key. IT S AN ELECTRONIC WATER METER. TECHNICAL SPECIFICATIONS Media Conductivity Viscosity Line Size Excitation Display Calibration Range Accuracy Linearity Repeatability Temperature Coefficient Process Temperature Process Pressure Material of construction Power Supply Low Bat indication Battery Life Response Time Transmitter Enclosure Process Connections Operating Conditions Data Logging Water > 5 µs/cm 200 cp max 15 NB to 40 NB Pulsed DC COG Graphical LCD display- 4 digit for Flow Rate & 6 digit for Totalizer Flow As per requirement (Factory Calibrated) +/- 1% of M.V. +/- 1% of M.V. +/- 0.5% of M.V. +/- 0.05% per C 65 ºC max 5 kg/cm² max Electrode - SS 316L Inbuilt Battery 3.6 V, 19 Ah Provided 2 to 10 years depending on sampling time. <10 Sec Die cast Aluminum IP66, flow tube IP68 BSP Threaded (F) Temperature -20 to 75 C / Humidity 5 to 95% non 25 O C For 5 years (per day 1 sample) OPTIONAL Communication Port 1) RS 232 for Data Downloading 2) Automatic Meter Reading (AMR- RF) / GSM 3) Pulse Note - For process conditions other than above please consult factory. 9

13 ELECTRONIC WATER METER ELMAG-600W DIMENSIONAL DETAILS H Mete r Size L (mm) D (mm) H (mm) Flow Range (m³ /hr) Min Normal Max 15 NB NB NB NB NB D Diameter H Height L Length L D Note Typical mounting dimensions for reference Standard factory calibration for 0.2 to 2 m/s velocity Max. flow range in LPH/LPM is upto 9999 ORDERING INFORMATION 05 40NB 04 32NB 03 25NB 03 Pulse (Open Collector) 02 20NB 02 AMR-GSM 01 15NB 01 RS232 SERIES ELMAG-600W Line Size Communicati on Output A 01 B 01 * Due to our continuous product improvisations, Design, Specifications and Model Number are subject to change without notice. * For GSM communication, SIM card & SCADA viewing software will be in customers scope. * Accuracy defined at lab conditions. * For better accuracy consult factory. 10

14 TWO WIRE ELECTROMAGNETIC FLOW METER ELMAG-600H SALIENT FEATURES Full bore type Suitable for conductive liquids 2 wire system with HART communication Material option depending upon process data Empty pipe indication Local Indication through Graphics LCD Maintenance free Simple & cost effective construction Inbuilt Data Logger DESCRIPTION The ELMAG-60H is a micro-controller based 2 wire full bore type electromagnetic flow transmitters specially used for various industrial applications. These flow transmitters accurately measure the flow rate of conductive liquids & slurries in closed pipes. Due to its simple & rigid design, the flow transmitter is an obstruction- less & maintenancefree instrument in place of conventional mechanical flow measuring device. The use of Pulsed DC technology offers highest ability & better measuring accuracy in the form of electrical signal 4-20 ma DC inearly proportional to volumetric flow, The instrument is based on Faraday s law of electromagnetic induction. A magnetic field is generated by the instrument in the flow tube. The fluid flowing through this magnetic field generates a voltage that is proportional to the flow velocity & corresponding electrical output is provided with respect to easuring voltage. TECHNICAL SPECIFICATIONS Media Conductivity Viscosity Line Size Excitation Type of Output Display Calibration Range Accuracy Linearity Repeatability Temperature Coefficient Process Temperature Process Pressure Material of construction Liquids (Conductive) > 5 µs/cm 200 cp max 15 NB to 600 NB Pulsed DC coil 4 to 20mA DC, 2 wire HART COG Graphic LCD display - 5 digit for Flow Rate & 8 digit for Totalizer Flow As per requirement (Factory Calibrated for std. 2m/s velocity) +/- 0.5% M.V.(For 20 to 100% flow) +/- 0.5% of M.V. +/- 0.2% of M.V. +/- 0.1% per C 85 C max for Rubber Lining & 220 C for PTFE Lining 10 kg/cm² max (higher on request) Lining - Neoprene Rubber / Hard Rubber / EPDM / PFA / PTFE Flange - MS / CS / SS316 Electrode - SS 316L/ Hastalloy C / Platinum / Tantalum Coil Housing - MS / SS 304 / SS V DC < 40mW <10 Sec Integral / Remote Electronics IP66, Flow Tube IP68 ASA150 flanged, as per table B 16.5 (Other On Requirement) In-Line Horizontal / Vertical Temperature -20 to 75 C / Humidity 5 to 95% non condensing Power Supply Power Consumption Response Time Electronics Transmitter Enclosure Process Connections Mounting Operating Conditions 11 Note - For process conditions other than above please consult factory.

15 ELMAG- 60H ELECTRO NET TWO WIRE ELECTROMAGNETIC FLOW METER ELMAG-600H DIMENSIONAL DETAILS FD Fig. Front View R D Fig. Side View Ø DBC Lining Ø Bolt Hole DIMENSIONAL DETAILS OF FLANGE(AS PER ASA150 # B-16.5) Line Size Flange Diameter of Diameter of Diameter No. Flange Flow Range(m 3 /hr) Diameter Raised Face Bolt Hole of Bolt of Distance at 0.03m/s to 6m/s Inch NB D R Circle DBC Hole Holes FD Minimum Maximum ½ / ½ ½ Note For Line size above 600NB consult factory. Typical mounting dimensions for reference. Standard factory calibration for 0.2 to 2 m/s velocity. Flow meter should be selected with the help of Nomograph recommended full scale velocity. Flow indication of 5 digit max. up to Measuring error (% M.V) Flow Nomograph 1.0% 0.9% 0.8% 0.7% 0.6% 0.5% 0.4% 0.3% 0.2% 0.1% 0.0% m/s Flow Velocity ORDERING INFORMATION 15NB To 600NB 08 Other 05 PTFE 02 Remote 02 SS Hard Rubber 01 Local 01 Aluminum 01 Neoprene Rubber Lining Enclosure Material 04 PFA 04 Tantalum 03 EPDM 03 Platinum 02 SS Other 02 SS Hyst. C mA + HART 09 10mtr 01 MS / CS 01 ASA MS 01 SS 316L mA 01 5mtr Series Line Size Electronics Electronic Flange Flange Coil Electrode Output Remote Material Rating Housing Material Cable Length ELMAG 60H A 15NB B 01 C 01 D 01 E 01 F 01 G 01 H 01 I 01 J 01 *Due to our continuous product improvisations, Design, Specifications and Model Number are subject to change without notice. *GSM output is without SIM card & SCADA viewing software. * For better accuracy consult factory. * Accuracy defined at lab conditions. 12

16 ELECTROMAGNETIC FLOW METER ELMAG-800 SALIENT FEATURES Suitable for conductive liquid Maintenance free Full bore type Simple & cost effective construction Power Supply 24V DC Supported by Flow view software DESCRIPTION The ELMAG-800 is a micro-controller based full bore type electromagnetic flow meters specially used for various industrial domestic applications. These flow meters accurately measures the flow rate of conductive liquid & slurries in closed pipes. Due to simple & rigid design, the flow meter is an obstruction less & maintenance free instrument in place of conventional mechanical flow measuring device. The use of Pulsed DC technology offers highest ability & better measuring accuracy in the form of electrical signal in the form of RS 485 communication linearly proportional to volumetric flow. The instrument is based on Faraday s law of electro-magnetic induction. A magnetic field is generated by the instrument in the flow tube. The fluid flowing through this magnetic field generates a voltage that is proportional to the flow velocity. Corresponding electrical output is provided with respect to measuring flow range. TECHNICAL SPECIFICATIONS Media Conductivity Viscosity Line Size Excitation Type of Output Calibration Range Accuracy Linearity Repeatability Temperature Coefficient Process Temperature Process Pressure Material of construction Power Supply Power Consumption Isolation Response Time Transmitter Enclosure Process Connections Mounting Operating Conditions Communication Liquids (Conductive) > 5 µs/cm 200 cp max 15 NB to 200 NB Pulsed DC RS 485 As per requirement (Factory Calibrated for std. 2m/s velocity) +/- 0.5% of F. S.(for 20 to 100% flow) +/- 0.5% of F. S. +/- 0.2% of F. S. +/- 0.05% per C 85 C max for Rubber Lining 10 kg/cm² max (higher on request) Lining - Rubber (5mm +/-1mm thick) Flange - CS / MS Electrode - SS 316L Coil Housing - MS 24 V DC < 10 VA 1.4 KV between Input, Output & Power Supply < 1 Sec Die cast Aluminium IP-66, flow tube IP-68 ASA 150 flanged, as per table B 16.5 (other on request) In-Line (Horizontal OR Vertical) Temperature 0 to 55 C / Humidity 5 to 95% non condensing RS

17 ELMAG 800 MODEL ELECTROMAGNETIC FLOW METER ELMAG-800 DIMENSIONAL DETAILS H SR. NO W FD Met er Size OD (mm) W (mm) H (mm) FD (m m) Flow Range (m³ /hr) Min Normal Max 15 NB NB NB NB NB NB NB NB NB NB NB NB OD Flange Diameter H Coil Housing Height FLOW NOMOGRAPH W Coil Housing width FD Flange to Flange distance Note Typical mounting dimensions for reference Standard factory calibration for 0 to 2m/Sec velocity Max. Flow range in LPH / LPM is upto 9999 Flow meter should be selected with the help of Nomograph recommended full scale velocity ORDERING INFORMATION 15 mm to 200 mm SERIES ELMAG-800 Line Size 65 mm *Due to our continuous product revisions, Design, Specifications and Model Number are subject to change without notice. *Accuracy defined at lab conditions. 14

18 ORIFICE FLOW METER DESCRIPTION The Orifice plate is the most common differential pressure flow primary element. It is based on proven technology has no moving parts and is suitable for high temperature and pressure applications. Orifice plates are recommended for clean liquids, gases and low velocity steam flows. Flow measurement using Orifice plates requires the accurate location of up stream and downstream pressure tappings. Various types of orifice carrier assemblies are available to suit a wide range of applications SALIENT FEATURES Orifice Design as per BS EN ISO 5167 Range of Orifice types 1) Concentric Square Edge 2) Quarter Circle 3) Segmental 4) Eccentric Non IBR and IBR certified Orifice assembly Availableinwidevarietyofmaterials Nomovingparts,simpleconstruction Maintenance-free TECHNICAL SPECIFICATIONS Service Line Size Type Ori ce Assembly Materials Liquid, Gas and Vapor Application ½ to 20 1) Concentric Square Edge 2) Quarter Circle 3) Segmental 4) Eccentric 1) Orifice plate with ANSI B16.36 Flange 2) Integral Orifice. 3) Carrier ring type SS316 Std.(Others on Request) TYPES OF ORIFICE 1. Square Edge For general applications in clean fluids - the most widely used design. Suitable for pipes up to 1000 mm diameter Concentric Square Edge 2. Quarter Circle Suitable for measurement of low Reynolds number flows in pipelines of diameter less than 750 mm. Quarter Circle Segmental Suitable for measurement for measurement of dirty fluids and 2 phase flow - allows passage of extraneous matter. Suitable for pipes up to 350mm 4. Eccentric Suitable for measurement of dirty fluids and 2 phase flow preferred to segmental pipelines of diameters less than 350 mm. Segmental Eccentric

19 ORIFICE FLOW METER ANSI B ORIFICE FLANGES Orifice Flanges are intended for use instead of standard pipe flanges when an orifice plate or flow nozzle must be installed. Pairs of pressure tappings are machined into the orifice flange, making separate orifice carriers or tappings in the pipe wall unnecessary. The range of orifice flanges covers all standard sizes and ranges, and all common flange materials. Flanges are available in socket weld or weld neck form, and are typically supplied with two ½ NPT tappings in each flange. Jacking screws to ensure ease of removal of the primary flow element are provided. Orifice flanges are supplied complete with bolting and gasket kits. INTEGRAL ORIFICE Typically consisting of a factory assembled section of pipe with an orifice plate mounted between two flanges near the center of the run, terminated with a flange at each end to connect to the process. Building the assembly in the factory allows us to control all the variables which can lead to inaccuracies which can arise if the system is assembled by untrained personnel on-site. Other advantages include reduced installation time; the completed section only needs to be bolted into the pre-prepared line. The complete assembly can be calibrated to provide the maximum accuracy. ANSI B ORIFICE FLANGE ASSEMBLY INTEGRAL ORIFICE PLATE ASSEMBLY ORIFICE MATERIAL 316 Stainless Steel Hastelloy C276 Hastelloy B3 Monel 400 Titanium Tantalum PTFEandPVDF. 16

20 Ultrasonic Meter

21 ULTRASONIC FLOW METER ASIONIC-400W SALIENT FEATURES DOMESTIC AMR ULTRASONIC FLOW METER ASIONIC 400W Ultrasonic transit time measurement Long Battery life RF Connectivity Meets OIML(R49) & MID standards Bidirectional flow measurement Inbuilt data logging TECHNICAL SPECIFICATIONS ASIONIC 400W is designed to measures the velocity of a fluid in a sealed pipeline fitted with transducers. This enables calculation of flow and volume based on time of flight principle. ASIONIC 400W is a static water meter which has no moving parts to avoid wear and tear. The electronic unit having inbuilt LCD display to continuously indicate and log / record the following parameters a. Flow rate b. Total volume c. Forward and reverse flow d. Battery status e. Unit of measurement f. Real time ASIONIC 400W is an integral and hermetically closed static water meter intended for the registration of cold and hot water consumption. ASIONIC 400W is constructed as a vacuum chamber of molded composite material. Thus, the electronics are fully protected against penetration of water. This means that the meter can, without problems, be placed in e.g. bathrooms, where it is sprayed with water daily, and it is also suitable for mounting in meter wells, which are frequently filled with water. The meter can and must only be opened by Oilog s authorized service center by means of special tools, if the meter has been opened, and seal have thus been broken, the meter is no longer valid for billing purpose. Furthermore, the factory guarantee no longer applies. The water meter is powered by an internal lithium battery with up to 10 years lifetime. the battery can be changed by one of the Oilog s authorized service center / personnel. 17

22 ULTRASONIC FLOW METER ASIONIC-400W Testing Pressure 16 Bar Nominal Pressure 10 Bar Minimum Pressure 0.1 Bar Pressure Loss < 0.63 Bar Media Temperature 0.1 to 60 OC Relative Humidity 100% Ambient Temperature 70 OC Max. mean temperature over 24 hours 55 OC Remote Reading Wireless M-Bus(incripted-protects personal data against unauthorized monitoring) Reprogramming / Downloading Store Data Through Optical Port using proprietary Water AMR software Data Storage Facility Up to 10 Years Battery life 10 Years RF Frequency MHz Available line sizes 15, 20, 25, 32, 40 NB MOC SS / ABS Process Connection BSP Threading(Male) ALARM Battery Low Alarm Meter Tamper Alarm Meter Open Alarm Meter Dry Alarm Reverse Flow Alarm Meter Overload Flow Alarm Meter Overload Pressure Alarm Continuous Zero Flow Alarm Leak / Continuous Flow Alarm Communication Signal / Indication ACCURACY The MPE for the upper flow rate zone (Q2 Q Q4) is ±2% for temperature from 0.1CO and ± 3% for temperature grater than 30OC.to 30CO, The MPE for the lower flow rate zone (Q1 Q Q2) is ±5% regardless of the temperature range. Q3 Indicating range (minimum values) 18 m³/h m³ Q

23 ULTRASONIC FLOW METER ASIONIC-400W DIMENSIONAL DETAILS H MODEL SR. NO D Meter Size L (mm) D Diameter H Height D (mm) H (mm) L Length Flow Range (m³ /hr) Min Normal Max 15 NB NB NB NB NB NB L Note Typical mounting dimensions for reference Standard factory calibration for 0 to 2m/Sec velocity Max. Flow range in LPH / LPM is upto 9999 ORDERING INFORMATION 15 mm to 50 mm 09 None 02 SS 03 GSM 01 CS / MS 02 RS 485 SERIES Line Size Flange Communication Port ASONIC mm A 01 B 02 *Due to our continuous product revisions, Design, Speci cations and Model Number are subject to change without notice. *Accuracy de ned at lab conditions & higher sampling rate. 19

24 ULTRASONIC FLOW METER ASIONIC-200 SALIENT FEATURES Ultrasonic measurement using transit time technology EMI / EMC Compliant Single / Dual / Quad beam technology for precise measurements Maintenance free Excellent long term stability & reliability Inline / Hot retractable sensor assembly Simple & cost effective construction Empty pipe indication Low start flow measuring capability to earn revenue from every drop of liquid delivered IP 68 Construction No pressure drop DESCRIPTION The Serie ASIONIC-200 is a micro-controller based full bore type Ultrasonic Flow Meter, specially used for various industrial applications. These flow meters accurately measures the flow rate of liquid in closed pipes. Due to its simple& rigid design, the flow meter is an obstruction-less & maintenance free instrument in place of conventional mechanical Flow measuring devices. The system is well suited to most environments. Programming of the flow meter is simple and can be accomplished with 4 keys available on instrument, It provides access to an extensive range of diagnostic information. Meter is manufactured in several flow meter consoles to meet the specific requirements of various applications. TECHNICAL SPECIFICATIONS Media Viscosity Line Size Display Calibration Range Acoustic Paths Sonically conductive liquids 200 cp maximum 50 NB to 2000 NB 6 digit for Flow Rate & 8 digit for Totalised Flow As per requirement (Factory Calibrated) Single, Dual & four path Accuracy* Line Size ±0.5% of MV ±1% of MV ±2% of MV 50 to 300NB Single path to 600NB Dual path Single path ---- Turbidity Linearity Repeatability Temperature Coefficient Process Temperature Process Pressure Material of Construction Power Supply Communication Port Analog Output Response Time Transmitter Enclosure Process Connections Operating Conditions Data logging Sensor Pair Sensor MOC Electronics 650 to 2000NB Four path Dual path Single path Smaller than 10,000ppm (mg/ltr) with a low level of air bubble content ± 0.5% of M.V. ± 0.2% of M.V. ± 0.05% per O C -20 O C to 85 O C maximum 15 kg/cm 2 maximum Flow tube - SS / MS / CS 1) 230V AC,50 Hz 2) 24V DC,+20%, -15% / 20 Watts Max. RS-485 MODBUS RTU 4-20 ma < 1Sec Die Cast Aluminum IP-66, flow tube IP-68 ANSI 150 flanged, as per table B 16.5 Temperature -20 to 75 O C / Humidity 5 to 95% non condensing for 10 years (per day 1 sample) As per requitement SS 316 1) Integral 2) Remote Note For process conditions other than above, please consult factory. 19

25 A S I ONIC 200 ELECTRON ET ASIONIC 200 ELECTRO NET ULTRASONIC FLOW METER ASIONIC-400W DIMENSIONAL DETAILS H A W Fig. 1 Front View DIMENSIONAL DETAILS OF FLANGE(AS PER ASA150 # B-16.5) Line Size Flange Diameter of Diameter of Diameter No. Flange Flow Range(m 3 /hr) Diameter Raised Face Bolt Hole of Bolt of Distance at 0.03m/s to 6m/s Inch NB D R Circle DBC Hole Holes FD Minimum Maximum ½ Note- Standard factory calibration for 0.2 to 2m/Sec velocity Typical mounting dimensions for reference Max. Flow range in LPH / LPM is up to For line size above 600NB consult factory for dimensions & flow range Fig. 2 Side View INSTALLATION DRAWING Valve Flow Out Flow In Pipe Support Pipe Support 5D 10D Valve Valve Pipe Support Pipe Support 19

26 ULTRASONIC FLOW METER ASIONIC-400W ORDERING INFORMATION NB NB mtr 03 Four 08 Other mtr 02 Remote 02 Dual 02 Fixed Inline 02 SS Other 02 SS mA + RS V DC 02 5 mtr NB 01 Local 01 Single 01 Hot retracta ble insertio n SERIES Line Size Electronics No. of paths Sensor Constructi on 01 MS 01 ASA Aluminum mA V AC 01 0 mtr Flow Tube Flange Rating Electronic s Enclosure Output Power Supply Remote Cable Length ASIONIC 200 A 01 B 01 C 01 D 01 E 01 F 01 G 01 H 01 I 01 J 01 *Due to our continuous product improvisations, Design, Specifications and Model Number are subject to change without notice. *Accuracy defined at lab conditions. 19

27 AUTOMATIC METER READER AMR 600 SALIENT FEATURES Increased Meter Reading Efficiency Through High Performance AMR. Accurate meter reading collection. Leak, tamper, and reverse flow alarms. Highly reliable RF communication with data encryption facility. Innovative remote Walk By automated reading solution. Uploads.CSV file to PC from Handheld unit over USB. Frequent transmit mode. Local display of HHU for operator convenience. DESCRIPTION The AMR 600 offers Walk By automated reading solution for efficient data collection with fewer efforts. Integrated RF transmitter with our own water meters makes it even more reliable and Cost effective. Eliminates the need for physical access or visual inspection of water meters, allowing gathering data from meters located in paces that are not easily accessible. Also eliminates the errors were present in manual meter reading system. TECHNICAL SPECIFICATIONS RF frequency band Display Transmission Interval RF output power Reception sensitivity Modulation technique Flow Meter Parameter readings HHU data Output Handheld memory Size Handheld Power Supply RF Bit rate AMR OPERATING SCHEME 865 MHz 867 MHz 16 x 2 LCD 13 Sec 17 Sec +12 dbm Down to -107 dbm FSK (Phase Shift Keying) Meter ID, Total Flow count, Battery Low flag, Back Flow flag, Leak detection flag, Meter Tampering flag CSV file over USB 512 Kb (4000 Records), Expandable (Optional) 2.4 V AA cell batteries 25 kbps *Due to our continuous product revisions, Design, Specifications and Model Number are subject to change without notice. *Accuracy defined at lab conditions & higher sampling rate. 20

28 Turbine Flow Meters

29 TWO WIRE TURBINE FLOW METER FL-100 SALIENT FEATURES 2 wire System Simple & cost effective construction Suitable for non conductive clear liquids. Local display as 8X1 LCD Durable & Versatile Easy maintenance Die Cast Aluminium IP-68 housing Remote display optionally available DESCRIPTION The FL-100 is a 2 wire turbine flow transmitter specially used for various industrial applications. The flowing media engages a vaned rotor causing it to rotate at an angular velocity proportional to flow rate. The pick-up coil senses the spinning motion of the rotor inside the pipe & converts it into a pulsating electrical signal. Summation of the pulsating electrical signal is directly related to the total flow. The frequency is linearly proportional to flow rate which is converted to electrical signal 4-20 ma. TECHNICAL SPECIFICATIONS Media Viscosity Line Size Display Transmitter Electronics Remote Electronics Cable Type of Output Calibration Range Accuracy Linearity Repeatability Pressure Drop Turn down ratio Process Temperature Process Pressure Material of construction Power Supply Power Consumption Response Time Temperature Coefficient Transmitter Enclosure Process Connections Liquids (Clear) 100 cp max 15 NB to 150 NB 8 x 1 LCD - 4 digit for flow rate & 8 digit for totalised flow (Flow rate & totalised flow will be visible through toggle key) Option 1 Integral Option 2 Remote 25 mtr max 1) 4 to 20 ma DC 2) Pulse - 30mA Peak-Peak As per requirement (Factory Calibrated) +/- 1% of F. S. (For 20 to 100% flow) +/- 1% +/- 1% Approx kg/cm 2 at max. Flow 10 1 to to 85 0 C max 0 to 10 kg/cm² max Bearings - Tungsten Carbide Sleeve / V Jewel Rotor - SS 410 / 17.4 PH Shaft - Tungsten Carbide Body / Support / Flange - SS 24 V DC < 0.5 VA < 100 msec +/- 0.01% per 0 C Die Cast Aluminum IP 68 1)ASA 150 RF,flanged as per table B ) BSP (M), Threaded ( Upto 50 NB only) 3)SS Tri-clover ( Upto 50 NB only) In-Line ( Horizontal or Vertical ) Temperature 0 to 55 0 C / Humidity 5 to 95% non condensing Mounting Operating Conditions Note For process conditions other than above please consult factory. 21

30 P FL-100 TWO WIRE TURBINE FLOW METER FL-100 DIMENSIONAL DETAILS D 100 mm 30 mm FD Line Size Flow Range Flange Details ANSI 150(B 16.5) m³/hr LPM D C R DBC d FD 15NB 0.4 to to NB 0.8 to to NB 1.6 to to NB 3.4 to to NB 6.8 to to NB 13.5 to to NB 27.0 to to Magnetic pick-up assembly SS 316 Flange RF DBC R D (OD)Outer Diameter of Flange No. of Holes For ½ to 3 & 4 to 6 C Thickness of flange R Diameter of Raised face DBC Diameter of bolt circle d Size of Hole FD Flange Diameter D mm d Note Typical mounting dimensions for reference ORDERING INFORMATION psi 4 0 Other 0 Other 0 Triclov er 3 15 mm to Pulse (Open 0 Remote 0 V Jewel PH 0 0 Flange 0 Collector) 150 mm d 2 0 Integral 0 Tungsten 4-20 ma 0 Thread 0 Carbide Sleeve ed 1 SERIES Line Size Electronics Bearing Rotor Output Process Pressu Connect re ion Ratting 600 psi Mtr 300 psi Mtr 150 psi 01 5 Mtr Remote Cable Length FL mm A 02 B 01 C 01 D 01 F 01 G 03 H 03 *Due to our continuous product revisions, Design, Specifications and Model Number are subject to change without notice. *Accuracy defined at lab conditions. 22

31 Flow Indicator / Totalizers

32 FLOW INDICATOR TOTALISER FL-244 SPECIFICATIONS Averaging of inputs for turbulent flow Software calibration Input Linear / Square Rooted 4-20 ma, 1-5V / 0-5V, 0-10 KHz Display 4 digit, 0.5 Red LED for Flow Rate & 8 digit, 0.3 Red LED for Totaliser Accuracy Better than ± 0.25% of F. S. Power Supply V AC, 50 Hz; OPTIONAL 24V DC Mounting Flush of the Panel DIN std. OR wall mounting WP enclosure Transmitter Supply 24V DC, 30 ma Retransmission Output 4-20 ma / 0-5 V, Isolated Alarm Output Potential free Relay Contact - 2 nos. for High, Low / Batch Communication Port RS 485 / RS 232 supporting MODBUS RTU protocol FLOW INDICATOR TOTALISER Micro-controller Based with LCD FL-600 / FL-600 PTC / FL-600 OC SPECIFICATIONS Averaging of inputs for turbulent flow Optional Available with 3 inputs for Pressure, Temperature, Compensated Flow Optional Available for OPEN CHANNEL Flow measurement Input Linear / Square Rooted / 10 Point Linearisation Table 4-20 ma, 1-5 V / 0-5 V, 0-10 Khz Accuracy Better than ± 0.25% of F. S. Power Supply V AC, 50 Hz; OPTIONAL 24V DC Mounting Flush of the Panel DIN std. OR wall mounting WP enclosure Transmitter Supply 24 V DC, 30 ma Retransmission Output 4-20 ma / 0-5 V, Isolated Alarm Output Potential free Relay Contact for High, Low / Batch Communication Port RS 485 / RS 232 supporting MODBUS RTU protocol 23

33 BARGRAPH INDICATORS DPI-160-1/ DPI SPECIFICATIONS Multi color bargraph display with 4 digit LED display for process variable Cold junction compensation for Thermocouple input. No. of Bargraph Segments 101 Nos. No. of Channels 01 No. (OPTIONAL DUAL CHANNEL) Input LINEAR 4-20mA, 0-20mA, 0-6V, 1-5V, -20µA to +20µA / RTD /THERMOCOUPLE Accuracy Better than ± 0.5% of F. S. for TC & ± 0.1% F.S. for other inputs Power Supply 24V DC ± 10% OPTIONAL Transmitter Supply 24 V DC, 30 ma / 60 ma Output 4-20 ma / 0-5 V, Isolated per channel, Alarm Output Potential free Relay Contact - 4 nos. Communication Port RS 485 UNIVERSAL INPUT PROCESS INDICATOR DPC-808 SPECIFICATIONS Cold junction compensation for Thermocouple input. Open sensor indication, Software calibration. Input 1 No; Universal - RTD / Thermocouple / Current /Voltage Display 4 x 1 digit, 0.8, 7 seg. Red LED Accuracy Better than ± 0.5% of F. S for TC & ± 0.25% F. S. for other inputs Power Supply 1) 24 V DC ; 2) V AC, 50 Hz Enclosure 1) Din std. ; 2) Weather-proof, IP-65; 3) Flameproof OPTIONAL Transmitter Supply 24 V DC, 30 ma Retransmission Output 4-20 ma / 0-5 V, isolated Alarm Output Potential free Relay Contact - 2 nos. Communication Port RS 485 / RS 232 with MODBUS RTU Protocol 24

34 DIGITAL PROCESS INDICATOR DPC-100/200/300 PROCESS SCANNER SC-204 SPECIFICATIONS Cold junction compensation for Thermocouple input. Open sensor indication, Software calibration. No. of Input 01 No. (OPTIONAL UPTO 3 INPUTS) Input Universal - RTD / Thermocouple / Current /Voltage Display 4 x 1 digit, 0.8, 7 seg. Red LED (OPTIONAL UPTO 3 DISPLAYS) Accuracy Better than ± 0.5% of F. S for Thermocouple & ± 0.25% F. S. for other inputs Power Supply 1) 24 V DC ; 2) V AC, 50 Hz OPTIONAL Transmitter Supply 24 V DC, 30 ma Retransmission Output 4-20 ma / 0-5 V, isolated Alarm Output Potential free Relay Contact - 2 nos Communication Port RS 485 / RS 232 with MODBUS RTU Protocol SPECIFICATIONS Individual alarm output for each channel. Long lasting battery backup for memory. Cold junction compensation for TC input. No. of Channels 8/16 nos. Input DEDICATED RTD/ TC/mA/ Voltage OR UNIVERSAL Display Scan Time Programmable from 1 to 99 seconds Power Supply V AC, 50 Hz / 24 V DC Accuracy Better than ± 0.25% F. S. for TC & RTD, ± 0.1% F. S. for other inputs Response Time < 100 msec per channel Output (common for all channels) RS 232/RS485 ; Printer Port (80 column parallel) ; Relay output OPTIONAL Alarm Output (Individual per channel) Potential free Relay Contacts for High & Low 25

35 DUAL INPUT ANALYSER UAC 100 Single / Dual channel. SPECIFICATIONS Input from ph/orp/conductivity/do2 Electrode and 4-20mA. Auto temperature compensation & Inbuilt memory for data logging. Power Supply 1) 24 V DC ; 2) 85 to 265V AC, 50Hz Type of Inputs From any ph / ORP / Conductivity / DO2 Electrode Input Range 1) ph, 0 to 14 ph 2) ORP, to 2000 mv 3)Conductivity, 0.01µS/cm to 10mS/cm 4)DO2, 0 to 20 ppm 5)Temperature, 0 to 150 deg C Output 1) 4-20 ma DC, HART (HART Optional for one channel) 2)Potential free Relay Contact (1 c/o, 1 Amp) - 2 nos, programmable 3)Serial communication RS485/RS232 ANALYTICAL TRANSMITTERS CT-100S / PH-100S / DO-100S SPECIFICATIONS On-line measurement. Auto/Manual temperature compensation Power Supply 24 V DC Display Local display 128X64 COG with backlit Type of Input From Conductivity / PH / DO Electrode (Single I/P) Type of Output 4-20 ma DC with HART COMMUNICATION, 2 wire Isolated Accuracy ± 0.25% F. S. Response Time < 1000 msec Process Connection Through BNC connector / Through Terminals Dimensions 135 (H) x 249 (W) including cable gland x 170 (D) in mm approx. Mounting 2 Pipe Mounting Housing Cast aluminium with epoxy coating NEMA 4X (IP- 65) 26

36 ANALYTICAL INDICATOR CONTROLLERS CT-801 / PH 104 / DO 801 SPECIFICATIONS Single channel ON/OFF Indicator controller. Open sensor indication. Software calibration. Power Supply 1) 24 V DC ; 2) V AC, 50 Hz Type of Input From Conductivity / PH / DO Electrode (Single I/P) Display 4 digit, 0.5 LED for ph & 16X2 LCD for Conductivity & DO Accuracy Better than ± 0.25% F. S. Process Connection Through BNC connector / Through Terminals Enclosure 1) DIN Std. 2) Weather-proof, IP-65 Mounting Flush of the Panel DIN std. & wall mount for FLP/WP enclosure Output 1) 4-20 ma DC 2)Potential free Relay Contact (1 c/o, 1 Amp) - 2 nos, programmable 3)Serial communication RS485/RS232 ANALYTICAL SENSORS CONDUCTIVITY SENSOR / ph - SENSOR / DO2 - SENSOR SPECIFICATIONS Large selection of electrodes to suit a wide variety of applications. Easy to install with stable performance & reliable measurement Range 1) For ph, 0 to 14 ph 2) For ORP, to 2000 mv 3) For Conductivity, 0.01µS/cm to 10mS/cm 4) For DO2, 0 to 20 ppm 5) For Temperature, 0 to 150 deg C System Accuracy ± 2 % OF F.S. Operating Temperature Range Customer to specify Operating Pressure Customer to specify Temperature Compensation Through RTD upto 100 o C Cable Length Upto 3 Mtrs 27

37 Mechanical Meters

38 28 ROTARY VANE WHEEL DRY-DIAL WATER METER DESCRIPTION Magnet drive, magnet-proof and resistance exterior magnet interference. Keep the reading easy and clear in a long-term service. FEATURES * Magnet drive, magnet-proof and resistance exterior magnet interference. * Keep the reading easy and clear in a long-term service. * The cover can be turned discretional. * Selected high quality materials for steady & reliable characteristic and good looking. * Brass or stainless steel body, hot water meter, magnet-proof device and remote reading transmission system for option. Note technical data conforms to ISO4064. TECHNICAL SPECIFICATIONS Main Technical Data Size (mm) Q3/Q1 Max Flow (m³/h) Nominal Flow (m³/h) Transitional Flow (m³/h) Min Flow (m³/h) Dimensions and weight Type LXSG- 40E size (mm) Length (mm) Width (mm) Height (mm) Connecting Thread G2B 4.8 Weight (kg)

39 29 ROTARY VANE WHEEL MULTI JET DRY METAL LXSG WATER METER DESCRIPTION Rotary vane wheel multi jet water meter Dry type and magnet drive water meter Easy reading High accuracy Remote water meter for option. 201 or 304 stainless steel water meter Size 15mm-25mm ISO 4064 class B Horizontal type and vertical type are available Pulse output for option FEATURES 1. High quality stainless steel material, NO.201 or NO Multi jet, dry dial or wet dial are available 3.Regular type and pulse-output communication for option. 4.Nice looking and perfect performance. 5.Magnet drive water meter, magnet-proof and resistance exterior magnet interference. 6.Water meter can keep the reading easy and clear in a long-term service. 7.The cover of water meter can be turned discretional. 8.Selected high quality materials for steady & reliable characteristic and good looking. 9.Brass or stainless steel body, hot water meter, magnet-proof device and remote reading transmission system for option Note technical data confirm to ISO4064 TECHNICAL SPECIFICATIONS Water meter size and basic information are below TYPE SIZE LENGTH WIDTH HEIGHT CONNECTING THREAD mm LXSG-15E / G3/4B LXSG-20E / G1B LXSG-25E G1 1/4B LXSG-32E G1 1/2B LXSG-40E G2B LXSG-50E G2 1/2B GB D=Φ165 D=Φ125

40 Valves and other accessories

41 30 BRASS GATE VALVES JY -101 Brass gate valve Forged brass body size 1/2 ; 3/4 ; 1 ; 1-1/4 ; 1-1/2 ; 2" ;2-1/2 ; 3 and 4" JY -102 Brass gate valve Forged brass body size 1/2 ; 3/4 ; 1 ; 1-1/4 ; 1-1/2 ; 2" ;2-1/2 ; 3 and 4" JY -103 Brass gate valve (CXC) Forged brass body size 1/2 ; 3/4 ; 1 ; 1-1/4 ; 1-1/2 ; 2" ;2-1/2 ; 3 and 4"

42 31 BRASS GATE VALVES JY -104 Brass gate valve Forged brass body size 1/2 ; 3/4 ; 1 ; 1-1/4 ; 1-1/2 ; 2 JY -105 Brass gate valve Forged brass body size 1/2" 3/4" 1" 1-1/4" 1-1/2" 2" JY -106 Brass gate valve Forged brass body size 1/2" 3/4" 1" 1-1/4" 1-1/2" 2"

43 32 BRASS GATE VALVES JY -107 Brass gate valve Forged brass body size 1/2" 3/4" 1" 1-1/4" 1-1/2" 2" JY -108 Brass gate valve Forged brass body size 1/2" 3/4" 1" 1-1/4" 1-1/2" 2" JY -109 Brass compression gate valve Forged brass body size 15mm; 18mm; 22mm; 28mm; 35mm; 42mm; 54mm JY -125 Brass gate valve with flange Cast brass body size 11/2" 2" 21/2" 3" 4"

44 33 BRASS STOP VALVES JY -110 Brass stop valve Forged brass body size 1/2" 3/4" 1" 1-1/4" 1-1/2" 2 JY -111 Brass stop valve forged brass body size 1/2" 3/4" 1" 1-1/4" 1-1/2" 2" JY -112 Brass stop valve forged brass body size 1/2" 3/4" 1" 1-1/4" 1-1/2" 2"

45 34 BRASS STOP VALVES JY -113 Brass stop valve forged brass body size 1/2" 3/4" 1" 1-1/4" 1-1/2" 2" JY -114 Brass stop valve Cast or forged brass body size 1/2" 3/4" 1" 1-1/4" 1-1/2" 2" JY -115 Brass stop valve Cast or forged brass body size 1/2" 3/4" 1" 1-1/4" 1-1/2" 2"

46 35 BRASS STOP VALVES JY -116 Brass compression stop valve forged brass body size 15mm 22mm JY -117 Brass stop valve forged brass body size 1/2" 3/4" 1" 1-1/4" 1-1/2" 2" JY -124 Brass stop valve Cast or forged brass body size " 2

47 36 BRASS CHECK VALVES JY -118 Brass check valve Cast brass body size 1/2" 3/4" 1" 1-1/4" 1-1/2" 2" 2-1/2" 3"4" JY -119 Brass check valve (CXC) Cast brass body size 1/2" 3/4" 1" 1-1/4" 1-1/2" 2" JY -120 Brass spring check valve forged brass body size 1/2" 3/4" 1" 1-1/4" 1-1/2" 2" 2-1/2" 3" 4"

48 37 BRASS FOOT VALVES JY -121 Brass foot valve With stainless steel filter forged brass body size 1/2" 3/4" 1" 1-1/4" 1-1/2" 2" J Y -122 Brass foot valve With brass filter Cast brass body size 1/2" 3/4" 1" 1-1/4" 1-1/2" 2" JY -123 Brass Y pattern strainer With stainless steel filter Cast or forged brass body size 1/2" 3/4" 1" 1-1/4" 1-1/2" 2"

49 38 BRASS BALL VALVES JY-201 Brass ball valve (standard port) F/F Forged or cast brass body Steel handle size 1/4" 3/8" 1/2" 3/4" 1" 1-1/4" 1-1/2" 2" 2-1/2" 3" 4" JY-202 Brass ball valve (Full port) F/F Forged brass body Steel handle with plastic sleeve size 1/4" 3/8" 1/2" 3/4" 1" 1-1/4" 1-1/2" 2" 2-1/2" 3" 4" JY-203 Brass ball valve (Full port) M/F Forged brass body Steel handle with plastic sleeve size 1/4" 3/8" 1/2" 3/4" 1" 1-1/4" 1-1/2" 2" JY-204 Brass ball valve (Full port) M/M Forged brass body Steel handle with plastic sleeve size 1/4" 3/8" 1/2" 3/4" 1" 1-1/4" 1-1/2" 2"

50 39 BRASS BALL VALVES JY-205 Brass ball valve with drain (Full port) Forged brass body Steel handle with plastic sleeve size 1/4" 3/8" 1/2" 3/4" 1" 1-1/4" 1-1/2" 2" JY-206 Brass ball valve (standard port) F/F Forged brass body Steel handle with plastic sleeve size 1/4" 3/8" 1/2" 3/4" 1" 1-1/4" 1-1/2" 2" 2-1/2" 3" 4" JY-207 Brass ball valve (Full port) F/F Forged brass body Steel handle with plastic sleeve size 1/4" 3/8" 1/2" 3/4" 1" 1-1/4" 1-1/2" 2" JY-208 Brass ball valve (Full port) F/F Forged brass body Steel handle with plastic sleeve size 1/2" 3/4" 1" 1-1/4" 1-1/2" 2"