Upgrade Options. Installation Guide WARNING

Transcription

1 Panasonic POWER BS G-CODE CY-V700U Panasonic XMD 000 L/C 44XXXXXX INTELLIGENT SYSTEM XM RADIO ID : XXXXXXXX Upgrade Options Installation Guide 5.-channel Surround System This unit has a built-in 4-channel amplifier. The procedure for setting up a 5.-channel surround system in order to play DVD software in a way that creates a you are there feel in a car is described below. Even if you are using this unit without installing a center speaker, surround speakers, or a subwoofer, it is still necessary to make the speaker settings in order to adjust the sound balance. Advanced system This unit can be combined with other components like shown below. For more details, refer to the operating instructions for the connected devices. Headrest Monitor: CY-V700U (option) Refer to Connection with Headrest Monitor (a page 3) Over-head Monitor: CY-VHD9500U (option) Refer to Connection with Over-head Monitor (a page 3) WARNING This installation information is designed for professional installers with knowledge of automobile electrical safety systems and is not intended for non-technical, do-it-yourself individuals. It does not contain instructions on the electrical installation and avoidance of potential harm to air bag, anti-theft and ABS braking or other systems necessary to install this product. Any attempt to install this product in a motor vehicle by anyone other than a professional installer could cause damage to the electrical safety system and could result in serious personal injury or death. Power amplifier Center Speaker: EAB-CF CD Changer: CX-DP880 (option) Refer to Connection with CD Changer (a page 8) DVD Changer: CX-DH80U (option) Refer to Connection with DVD Changer (a page 9) If your car is equipped with air bag and/or anti-theft systems, specific procedures may be required for connection and disconnection of the battery to install this product. Before attempting installation of this electronic component against the manufacturer's recommendation, you must contact your car dealer or manufacturer to determine the required procedure and strictly follow their instructions. Front Speakers: CJ-DVD77 Camcorder (option): Refer to Connection with VCR or camcorder (a page ) FAILURE TO FOLLOW THE PROCEDURE MAY RESULT IN THE UNINTENDED DEPLOY- MENT OF AIR BAGS OR ACTIVATION OF THE ANTI-THEFT SYSTEM RESULTING IN DAM- AGE TO THE VEHICLE AND PERSONAL INJURY OR DEATH. Surround Speakers: CJ-SS6 VCR (option): Refer to Connection with VCR or camcorder (a page ) Power amplifier Subwoofer: CJ-HD30 may be coming... Rear View Camera (option): Refer to Connection with Rear View Camera (a page ) XM Satellite Radio (option): Refer to Connection with Rear XM Satellite Radio (a page 0) Car navigation system: (may come on the market in the future) This manual refers to the connection to the Panasonic car navigation system that may possibly come on the market in the future. Descriptions regarding the connection with Panasonic car navigation system are boxed with dotted line. Overview This product should be installed by a professional. However, should you decide to install the product against the manufacturer s recommendation, these operating Instructions do not contain electrical installation instructions. You must contact your car dealer or manufacturer for electrical connection instructions to avoid possible damage to your electrical safety systems and resulting injury or death. (Please refer to the WARNING statement above). Your next step is to decide where to install the unit. The instructions in these pages will guide you through the remaining steps: Identify and label the car wires. Connect the car wires to the wires of the power connector. Install the unit. Check the operation of the unit. If you encounter problems, please consult your nearest professional installer. Warning This unit operates with a V DC negative ground auto battery system only. Do not attempt to use it with any other system. Doing so could cause serious damage. Before you begin installation, look for the following items which are packed with your unit. Operating Instructions (including Limited Warranty and Customer Service Directory ). Installation Hardware...Needed for Installation. 6 CQ-VD700U CQ-VD700U 7

2 Installation Guide (continued) 3 Installation Hardware (For Installation) No. Item Diagram Qty. q Trim Plate <YEP9FZ739> w Mounting Collar <YEFG0694> e Mounting Spring <YEFX00574> r Mounting Bolt (5 mmø) Tapping Screw t y Hex. Nut (5 mmø) <ZZBISVD700A> u Rear Support Strap i Round Head Screw <YEFG0409> o Flat-Head Screw 4!0 Round Head Screw (4 mmø x 3 mm) 4 <ZZBISVD700B>! Spacer! Double-Faced Adhesive Tape set <ZZBISVD700E> Installation Hardware (For Wiring) No. Item Diagram Qty.!3 Power Connector <YAJ04C3A>!4 Reverse Extension Cord <WAVS05M6000T>!5 Clip Connector <YEAT034C0> The number in parenthesis underneath each accessory part name is the part number for maintenance and service. Accessories and their parts numbers are subject to modification without prior notice due to improvements. Before Installation Warning Do not install the monitor in a location which obstructs driving, visibility or which is prohibited by applicable laws and regulations. If the monitor is installed in a location which obstructs forward visibility or operation of the air bag or other safety equipment or which interferes with operation of the car, it may cause an accident. Never use bolts or nuts from the car's safety devices for installation. If bolts or nuts from the steering wheel, brakes or other safety devices are used for installation of the monitor, it may cause an accident. Attach the wires correctly. If the wiring is not correctly performed, it may cause a fire or an accident. In particular, be sure to run and secure the lead wire so that it does not get tangled with a screw or the moving portion of a seat rail. Use with V DC negative ground car. This unit is only for use with a V DC negative ground car. It cannot be used in large trucks or diesel cars which are 4 V DC cars. If it is used in the wrong type of car, it may cause a fire or an accident. Use the specified fuse. Be sure to always use the specified fuse. If a fuse other than the specified fuse is used, it may cause a fire or an accident. Do not damage the cord by pinching or pulling it. Do not pull or damage the cord. If the cord is not treated properly, it will short out or be severed and may cause a fire or an accident. Dashboard Specifications THICKNESS MIN mm {3/6 } MAX mm {7/3 } 8 mm {7-5/3 } 53 mm {-3/3 } Identify All Leads The first step in installation is to identify all the car wires you ll use when hooking up your LCD monitor. As you identify each wire, we suggest that you label it using masking tape and a permanent marker. This will help avoid confusion when making connections later. Do not connect the power connector to the display unit until you have made all connections. If there are no plastic caps on the hooking wires, insulate all exposed leads with electrical tape until you are ready to use them. Identify the leads in the following order. Power Lead If your car has a radio or is pre-wired for one: Cut the connector wires one at a time from the plug (leaving the leads as long as possible) so that you can work with individual leads. Turn the ignition on to the accessory position, and ground one lead of the test bulb to the chassis. 4 Required Tools You ll need a screwdriver and the following: V DC Test Bulb Electrical Tape Side-Cut Pliers Touch the other lead of the test bulb to each of the exposed wires from the cut radio connector plug. Touch one wire at a time until you find the outlet that causes the test bulb to light. Now turn the ignition off and then on. If the bulb also turns off and on, that outlet is the car power lead. If your car is not wired for an audio unit: Go to the fuse block and find the fuse port for radio (RADIO) accessory (ACC) or ignition (IGN). Battery Lead If your stereo unit has a yellow lead, you will need to locate the car's battery lead. Otherwise you may ignore this procedure. (The yellow battery lead provides continuous power to maintain a clock or other functions.) 8 CQ-VD700U CQ-VD700U 9

3 5 Installation Guide (continued) If your car has a radio or is pre-wired for one: With the ignition and headlights off, identify the car battery lead by grounding one lead of the test bulb to the chassis and checking the remaining exposed wires from the cut radio connector plug. If your car is not wired for an audio unit: Go to the fuse block and find the fuse port for the battery, usually marked BAT. Speakers (not supplied) Identify the car speaker leads. There are two leads for each speaker, usually color coded. A handy way to identify the speaker leads and the speaker they are connected with is to test the leads using a.5 V AA battery as follows. Hold one lead against one pole of the battery and stroke the other lead across the other pole. You will hear a scraping sound in a speaker if you are holding a speaker lead. If not, keep testing different lead combinations until you have located all the speaker leads. When you label them, include the speaker location for each. Connect All Leads Now that you have identified all the wires in the car, you're ready to begin connecting them to the LCD monitor wires. Electrical Connections (a page 6-3) shows the proper connections and color coding of the leads. We strongly recommend that you test the unit before making a final installation. You can set the unit on the floor and make temporary connections to test the unit. Use electrical tape to cover all exposed wires. Important: Connect the red power lead last, after you have made and insulated all other connections. Ground Connect the black ground lead of the power connector to the metal car chassis. Speakers Connect the speaker wires. See the wiring diagram for the proper hookups. Follow the diagram carefully to avoid damaging the speakers and the stereo unit. The speakers used must be able to handle more than 50 W of audio power. If using optional audio power, the speakers should be able to handle the maximum amplifier output power. Speakers with low input ratings can be damaged. Speaker impedance should measure 4 8 Ω, which is typically marked on most speakers. Lower or higher impedance speakers will affect output and can cause both speaker and stereo unit damage. Never ground the speaker cords. For example, do not use a chassis ground system or a three-wire speaker common system. Each speaker must be connected separately using parallel insulated wires. If in doubt about how your car s speakers are wired, please consult with your nearest professional installer. Battery Connect the yellow battery lead to the correct radio wire or to the battery fuse port on the fuse block. Equipment Connect any optional equipment according to the instructions furnished with the equipment. Read the operating and installation instructions of any equipment you will connect to this unit. Power Connect the red power lead to the correct car radio wire or to the appropriate fuse port on the fuse block. If the LCD monitor functions properly with all these connections made, disconnect the wires and proceed to the final installation. Final Installation Lead Connections Connect all wires, making sure that each connection is insulated and secure. Bundle all loose wires and fasten them with tape so they will not fall down later. Now insert the LCD monitor into the mounting collar. Congratulations! After making a few final checks, you re ready to enjoy your new LCD monitor. Final Checks. Make sure that all wires are properly connected and insulated.. Make sure that the LCD monitor is securely held in the mounting collar. 3. Turn on the ignition to check the unit for proper operation. If you have difficulties, consult your nearest authorized professional installer for assistance. Precautions We strongly recommend that you wear gloves for installation work to protect yourself from injuries. When bending the mounting tab of the mounting collar with a screwdriver, be careful not to injure your hands and fingers. Disconnect the cable from the negative ( ) battery terminal (see caution at right). Unit should be installed in a horizontal position with the front end up at a convenient angle, but less than 30. Warning If your car is equipped with air bag and/or anti-theft systems, specific procedures may be required for connection and disconnection of the battery to install this product. Before attempting installation of this electronic component against the manufacturer's recommendation, you must contact your car dealer or manufacturer to determine the required procedure and strictly follow their instructions. FAILURE TO FOLLOW THE PROCEDURE MAY RESULT IN THE UNINTENDED DEPLOYMENT OF AIR BAGS OR ACTIVATION OF THE ANTI-THEFT SYSTEM RESULTING IN DAMAGE TO THE VEHICLE AND PERSONAL INJURY OR DEATH Transportation Bracket Removal Be sure to remove the transportation brackets before use (installation). Use round head screws for installation. (a page 4) Be careful not to lose these screws. Round Head Screw Transportation Bracket Various settings that have been stored in the memory in other on-board equipment (car navigation etc.) may be lost if the battery terminals are disconnected. Therefore, we recommend you to make a record of or to back up the settings before disconnecting the terminals. After completing installation of the main unit, set up the equipment again according to the settings. This unit should be professionally installed. In case of difficulty, please consult with your nearest professional installer.. This unit only operates in a V DC negative ground system.. Follow the Electrical Connections carefully (a page 6-3). Failure to do so may result in damage to the unit. 3. Connect the power lead after all other connections are made. 4. Be sure to connect the battery lead (yellow) to the positive terminal (+) of the battery or fuse block (BAT) terminal. 5. Insulate all exposed wires to prevent short circuiting. 6. Secure all loose wires after installing the unit. 7. Please carefully read the operating and installation instructions of the respective equipment before connecting it to this unit. Please follow the laws and regulations of your state, province or country for installation of the unit. Round Head Screw Transportation Bracket 6 0 CQ-VD700U CQ-VD700U

4 Installation Guide (continued) 7 Installation Procedures (When using Mounting Collar w) The car model, installation conditions and combination of the units used may impose some restrictions on opening and closing the monitor as well as on the angle and position to which the monitor can be adjusted. IMPORTANT When this unit is installed in dashboard, ensure that there is sufficient air flow around the unit to prevent damage from overheating. Do not block any ventilation holes on the unit. Mounting the Display Unit Insert the Mounting Collar w into the dashboard, and bend the mounting tabs out with a screwdriver. Fastening the Mounting Collar How much to bend the tabs will vary depending on the car. Bend them with a screwdriver to fasten the Mounting Collar w securely in the dashboard. Tab w Mounting Collar Dashboard Method for Fixing the Mounting Spring Two holes of the mounting spring allow you to select between two mounting types as shown below. (A) Regular installation method A few millimeters of console projecting (B) Deeper installation method Less projecting 8 r Mounting Bolt (5 mmø)!3 Power Connector Method (B) is not available in some types of cars. e Mounting Spring Attach the Mounting Springs e to the unit. Establish the rear connection of the unit. After fixing Power Connector!3, fix the rear of the unit to the car body by either method (a) or (b) shown at right. Insert the unit into Mounting Collar w. Secure the clamp plate of Mounting Collar w to the hook of Mounting Spring e. Insert Trim Plate q. After installation reconnect the negative ( ) battery terminal. Clamp plate Method for Fixing the Rear of the Unit (a) Using the Rear Support Strap u. u Rear Support Strap Fire wall of car t Tapping Screw 3 mmø y Hex. Nut (5 mmø) r Mounting Bolt (5 mmø) (b) Using the Rubber Cushion (option) Rubber Bushing (option) Rear Support Bracket (Provided on the Car) r Mounting Bolt (5 mmø) CQ-VD700U CQ-VD700U 3

5 9 Installation Guide (continued) Installation Procedures (When not using Mounting Collar w) Use the brackets supplied with your car when mounting this unit. The bracket shape and mounting method vary with car manufacturers, car types and manufacturing year. Please consult your nearest dealer or installer. Select mounting screws according to the hole positions and hole shape of the bracket. i Round Head Screw pieces Recycle the Round Head Screws that fixed the transportation brackets for two more positions.!0 Round Head Screw (4 mmø x 3 mm) 4 pieces When using these mounting holes Connecting the Side Brake (Parking Brake) Connection Lead For safety, be sure to ask your nearest professional installer to do this connection. Hand brake Foot brake Side brake (parking brake) switch 0 4 pieces Use the supplied Spacer! if mounting hole of your car is shaped like below. i Round Head Screw The side brake (parking brake) switch position varies with car model. For details on the exact location of the side brake (parking brake) switch in your car, contact your dealer. Mounting Hole of a Bracket (in section) Bracket! Spacer Existing Bracket (R)! Double-Faced Adhesive Tape SIDE BRAKE Side Brake (Parking Brake) Connection Lead (Blue/yellow stripe) When the side brake (parking brake) lever is engaged, the unit is grounded by the chassis.!5 Clip Connector Brake light Battery + Car chassis i Round Head Screw! Spacer! Double-Faced Adhesive Tape Existing Bracket (L) (Bracket originally attached to the car) To Remove the Unit q Push the right and left clamp plates outward, one at a time, and pull the unit toward yourself. w After removing the right and left clamp plates, pull the unit with both hands till it comes out. q Attach a Clip Connector!5 to the end of the side brake (parking brake) connection lead. w The Clip Connector!5 is connected to the power source side lead of the side brake (parking brake) lever. q w Comes up to this point. Push here to remove the clamp plates. Side Brake (Parking Brake) Connection Lead (Blue/yellow stripe) Power source side lead * To remove Trim plate q, pull it from right side to left side. 4 CQ-VD700U CQ-VD700U 5

6 Electrical Connections This unit is designed for use in a car having a V negative ground battery system. Be sure to insulate any exposed wires from the car chassis. Bundle all cables and keep cable terminals free from any metal parts. Note that if your car has a driving computer or a navigation computer, disconnecting the cable from the battery may clear the memory. Run the cords avoiding the spots where the temperature can be extremely high. To prevent from damage to the unit, be sure to follow the wiring diagrams below. Be sure to fully plug in the connectors. Secure them with clamps and tapes. All other installation methods require the use of dedicated metal fittings. Consult with a qualified servicing engineer or your dealer if other methods are required. This manual refers to the connection to the Panasonic car navigation system that may possibly come on the market in the future. Descriptions regarding the connection with Panasonic car navigation system are boxed with dotted line. RGB Connector To the Panasonic Car Navigation System (available in future). DIN Connector To the DIN connector of a CD changer/dvd Changer. (e.g. CX-DP880, CX-DH80U). Navi Mute Lead (Orange) Connect to the Navi Mute Lead of the Panasonic car navigation system. (available in future)!3 Power Connector NAVI MUTE ANT-CONT MAX 0.A Motor Antenna Relay Control Lead (Blue) (To motor antenna) (Max. 00 ma) This lead is not intended for use with a switch actuated power antenna. SIDE BRAKE Side Brake (Parking Brake) Connection Lead (Blue/yellow stripe) Be sure to wire the side brake (parking brake) for safety and preventing accidents. (a page 5) AMP-CONT MAX 0.A External Amplifier Control Power Lead (Blue/white stripe) To an external amplifier. FRONT SP Front Right + (Gray) Front Right (Gray/black stripe) Front Left + (White) Front Left (White/black stripe) VIDEO-OUT REMOTE-OUT PRE-OUT FRONT CQ-VD700U Radio Antenna Connector (RADIO ANT IN) Video Output Terminal (VIDEO-OUT) Connect the rear monitor. (a page 3) Remote-Out Lead To Remote-In of connected device. Pre-Out Connector (front) To external amplifier. REVERSE Reverse Lead (Violet/white stripe) When connecting the rear view camera, use the reverse lead. (a page ) Use a Reverse Extension Cord!4 if needed. ACC Power Lead (Red) To ACC power, + V DC. Battery Lead To the car battery, continuous + V DC. (Fuse 5 A) BATTERY 5 A (Resistor kω) (Noise Filter) Ground Lead To a clean, bare metallic part of the car chassis REAR SP Speaker connections Rear Right + (Violet) Rear Right (Violet/black stripe) Rear Left + (Green) Rear Left (Green/black stripe) Do not connect more than one speaker to one set of speaker leads (except for connecting to a tweeter). Do not use a 3-wire type speaker system having a common earth lead. PRE-OUT CENTER PRE-OUT REAR S.W-OUT VTR-IN CH/AUX-IN CAMERA-IN REMOTE-IN (Brown/black stripe) TV-CONT (Blue/red stripe) Pre-Out Connector (center) To external amplifier. Pre-Out Connector (rear) To external amplifier. Pre-Out Subwoofer connector (mono) To external amplifier. Video Input Terminal (VTR-IN) Connect a VCR, camcorder, other brand s car navigation system, etc. (a page ) Changer/AUX/XM receiver Input Connector To the RCA cord of a changer/aux/xm receiver. Camera Input Terminal (CAMERA-IN) Connect a rear view camera. (a page ) Remote-In Lead (not used) TV Control Lead (TV-CONT) (not used) 6 CQ-VD700U CQ-VD700U 7

7 Electrical Connections (continued) 3 Connection with CD Changer (CX-DP880) CD Changer CX-DP880 (option) Connection with DVD Changer (CX-DH80U) There are two types of changer connections as follows. Observe the features for each before connection. Type A : You can control the changer with the main unit. But the rear monitor does not display any images. Type B : You can see images on the rear monitor. But the changer should be controlled independently. DVD Changer CX-DH80U (option) 4 Power Connector (Supplied with CX-DP880) DIN Connector Ground Lead To a clean, bare metallic part of the car chassis Battery Lead To the car battery, continuous + V DC DIN Cord Ground Lead To a clean, bare metallic part of the car chassis Battery Lead BATTERY 5 A To the car battery, continuous + V DC Remote-In (RCA) Power Connector (Supplied with CX-DH80U) RCA Cord CH/AUX-IN CQ-VD700U A Power Lead (Red) (not used) ACC (L) (White) RCA Cord DIN Cord (black) DIN Connector Remote Control Sensor Extension Cord (option) Remote-Out Lead CAMERA-IN CH/AUX-IN Camera Input Lead REMOTE-OUT CQ-VD700U Power Lead (Red) To ACC power, + V DC. B ACC (L) (White) RCA Cord DIN Cord (not used) Remote Control Sensor Extension Cord (option) Remote-Out Lead VTR-IN REMOTE-OUT CQ-VD700U 8 CQ-VD700U CQ-VD700U 9

8 Panasonic 5 Electrical Connections (continued) Connection with XM Satellite Radio (XMD000) XM Satellite Radio XMD000* (option) XMDPAN00* (option) Ground Lead To a clean, bare metallic part of the car chassis DIN Connector RCA Cord (option) DIN Cord Connection with Rear View Camera CQ-VD700U Camera Input Rear View Camera (option) Rear View Camera Control Unit (option) 6 Battery Lead To the car battery, continuous + V DC!3 Power Connector RCA Cord (option) Power Lead (Red) To ACC power, + V DC. CQ-VD700U CH/AUX-IN REVERSE Reverse Lead (Violet/white stripe) CAMERA-IN Camera Input Terminal * Please understand that Panasonic is not liable for modification of specifications, shape, name, and the like of the optional XM receiver and digital adapter without prior notice because they are not manufactured by Panasonic. Connecting the Reverse Lead If using an optional rear view camera, the reverse lead must be connected. Connect the reverse lead (violet/white stripe) to the positive (+) lead of the reverse lamp (the lamp with a clear lens that lights when the transmission gear is shifted into the reverse position). Connect the reverse lead after cutting the terminal at the end. Use a Reverse Extension Cord!4 if needed. Check the reverse lamp. Take it out of the back of the tail lamp mount. Reverse lamp Clip connector (option) Battery Car chassis!4 Reverse Extension Cord (Violet/white stripe) P R N D L Transmission gear 0 CQ-VD700U CQ-VD700U

9 BS G-CODE INTELLIGENT SYSTEM CY-V700U Electrical Connections (continued) 7 Connection with VCR or Camcorder Please observe what shapes the connectors of the connecting devices are and where each of them is connected to in order to establish a proper connection. Connection with Over-head Monitor Please observe what shapes the connectors of the connecting devices are and where each of them is connected to in order to establish a proper connection. 8 CQ-VD700U For people sitting in the front seats, please enjoy only audio during driving. (L) (White) (R) (Red) VTR-IN RCA Cord (option) (R) (Red) POWER (L) (White) Video Output Audio Right Audio Left VIDEO-OUT RCA Cord (option) Connection with Headrest Monitor For people sitting in the front seats, please enjoy only audio during driving. Over-head Monitor CY-VHD9500U (option) Camcorder (option) VCR (option) Headrest Monitor CY-V700U (option) PHONES VIDEO-OUT RCA cord (option) CY-V700U Hide-away unit (Front) VTR VTR CQ-VD700U CQ-VD700U 3