Electronic Sensors Solid State, Reed and Proximity Sensors

Transcription

1 Electronic Solid State, Reed and Proximity Contents Sensor Selection Guides... Solid State (Hall Effect) and Reed Specifications P8S Global and Accessories... 5 PA Series and Accessories... 0 LP/LPM Series... RC Series... 3 PV, WR, XR Series... 4 PTR Series... 6 Cordsets... 8 Valvetronic 0 Connection Block... 9 End-of-Stroke Proximity A, AN, MA Series Cylinders... 0 PTR and HP Series Rotary Actuators... 5 WR Series Wrist Rotators... 6 XL and HB Series Guided Cylinders... 6 Parker Hannifin Corporation

2 Selection Guide PNP Solid State Round Body Cylinders Compact Cylinders PA Series Standard Sensor PA Series Right Angle Sensor PL Series SRM/SRDM Series P Series All PM Series Standard Sensor All PM Series Short Sensor LPM Series PNP Solid State Sensor Selection Chart 3 m Flying Leads 0m Flying Leads 8 mm Quick Connect 8 mm Quick Connect w/ m Lead mm Quick Connect Bracket Sensor Reference Page # 0 mm Bore PA-XHK* N/A PA-XJH* N/A N/A PA-CCC 0 0 mm Bore PA-XHK* N/A PA-XJH* N/A N/A PA-DCC mm Bore PA-XHK* N/A PA-XJH* N/A N/A PA-FCC mm Bore PA-XHK* N/A PA-XJH* N/A N/A PA-HCC mm Bore PA-XHK* N/A PA-XJH* N/A N/A PA-JCC mm Bore PA-XMK* N/A N/A N/A N/A PA-CCC 0 0 mm Bore PA-XMK* N/A N/A N/A N/A PA-DCC mm Bore PA-XMK* N/A N/A N/A N/A PA-FCC mm Bore PA-XMK* N/A N/A N/A N/A PA-HCC mm Bore PA-XMK* N/A N/A N/A N/A PA-JCC mm Bore P8S-GPFLX P8S-GPFTX P8S-GPSHX N/A P8S-GPMHX P8S-TMC mm Bore P8S-GPFLX P8S-GPFTX P8S-GPSHX N/A P8S-GPMHX P8S-TMC mm Bore P8S-GPFLX P8S-GPFTX P8S-GPSHX N/A P8S-GPMHX P8S-TMC /6" - 3/4" Bore P8S-GPFLX P8S-GPFTX P8S-GPSHX N/A P8S-GPMHX P8S-TMC /6" - -/" Bore P8S-GPFLX P8S-GPFTX P8S-GPSHX N/A P8S-GPMHX P8S-TMC /8" - -/" Bore P8S-GPFLX P8S-GPFTX P8S-GPSHX N/A P8S-GPMHX P8S-TMC " - 4" Bore P8S-GPFLX P8S-GPFTX P8S-GPSHX N/A P8S-GPMHX P8S-TMC All Bore Sizes P8S-GPFLX P8S-GPFTX P8S-GPSHX N/A P8S-GPMHX N/A 6 All Bore Sizes P8S-SPELXD P8S-SPETXD P8S-SPTHXD N/A N/A N/A 8 Bracket Reference Page # 9/6" Bore L ** N/A L C N/A N/A N/A 3/4" - -/8" Bore L ** N/A L C N/A N/A N/A -/" - " Bore L ** N/A L C N/A N/A N/A -/" - 4" Bore L ** N/A L C N/A N/A N/A Tie Rod Cylinders MA/MAE/ MNR Series PD Series Standard & Clean Profiles PD Series Tie Rod Version All Bore Sizes P8S-GPFLX P8S-GPFTX P8S-GPSHX N/A P8S-GPMHX P8S-TMA0X 6 9 All Bore Sizes P8S-GPFLX P8S-GPFTX P8S-GPSHX P8S-GPSCX P8S-GPMHX N/A 6 All Bore Sizes P8S-GPFLX P8S-GPFTX P8S-GPSHX P8S-GPSCX P8S-GPMHX P8S-TMA0X 6 9 MP Series All Bore Sizes P8S-GPFLX P8S-GPFTX P8S-GPSHX N/A P8S-GPMHX P8S-TMA0X 6 9 Rodless Cylinders Linear Slides PY Series Standard Sensor All Bore Sizes P8S-GPFLX P8S-GPFTX P8S-GPSHX N/A P8S-GPMHX N/A 6 PY Series Short Sensor All Bore Sizes P8S-SPELXD P8S-SPETXD P8S-SPTHXD N/A N/A N/A 8 RC Series All Bore Sizes L *** N/A L C N/A N/A N/A 3 Flush Mount Type P8S-GPFLX P8S-GPFTX P8S-GPSHX N/A N/A N/A 6 P5T Series Right Angle Type P8S-SPELXD P8S-SPETXD P8S-SPTHXD N/A N/A N/A mm Bore P8S-GPFLX N/A P8S-GPSHX N/A N/A GSB- 6 C.F. P5E Series mm Bore P8S-GPFLX N/A P8S-GPSHX N/A N/A GSB- 6 C.F mm Bore P8S-GPFLX N/A P8S-GPSHX N/A N/A GSB-3 6 C.F. HB Series All Sizes P8S-GPFLX P8S-GPFTX P8S-GPSHX N/A P8S-GPMHX GSB- 6 C.F. Sizes 04 and 06 P8S-GPFLX P8S-GPFTX P8S-GPSHX N/A P8S-GPMHX P8S-TMC0 6 9 XL Series Sizes 08 and P8S-GPFLX P8S-GPFTX P8S-GPSHX N/A P8S-GPMHX P8S-TMC0 6 9 Rotary Actuators PV Series WR Series XR Series PTR Series Normally Open SMH-P** N/A SMH-PC N/A N/A N/A 4 Normally Open N/A N/A N/A N/A N/A N/A Normally Closed SMC-P** N/A SMC-PC N/A N/A N/A 4 Size 0 and 5 N/A SWH-P*** SWH-PC N/A N/A Included 6 Size 0, 5 and 3 N/A SWH-P*** SWH-PC N/A N/A Included 6 * Flying leads are meters in length ** Flying Leads are.5 meters in length *** Flying leads are meter in length Based on MA Cylinder C.F. = Consult Factory for dimensions. Parker Hannifin Corporation

3 Selection Guide NPN Solid State Compact Cylinders Round Body Cylinders PA Series Standard Sensor PA Series Right Angle Sensor PL Series SRM/SRDM Series P Series All PM Series Standard Sensor All PM Series Short Sensor LPM Series NPN Solid State Sensor Selection Chart 3 m Flying Leads 0m Flying Leads 8 mm Quick Connect 8 mm Quick Connect w/ m Lead mm Quick Connect Bracket Sensor Reference Page 0 mm Bore PA-XEK* N/A PA-XFH* N/A N/A PA-CCC 0 0 mm Bore PA-XEK* N/A PA-XFH* N/A N/A PA-DCC mm Bore PA-XEK* N/A PA-XFH* N/A N/A PA-FCC mm Bore PA-XEK* N/A PA-XFH* N/A N/A PA-HCC mm Bore PA-XEK* N/A PA-XFH* N/A N/A PA-JCC mm Bore PA-XLK* N/A N/A N/A N/A PA-CCC 0 0 mm Bore PA-XLK* N/A N/A N/A N/A PA-DCC mm Bore PA-XLK* N/A N/A N/A N/A PA-FCC mm Bore PA-XLK* N/A N/A N/A N/A PA-HCC mm Bore PA-XLK* N/A N/A N/A N/A PA-JCC mm Bore P8S-GNFLX P8S-GNFTX P8S-GNSHX N/A P8S-GNMHX P8S-TMC mm Bore P8S-GNFLX P8S-GNFTX P8S-GNSHX N/A P8S-GNMHX P8S-TMC mm Bore P8S-GNFLX P8S-GNFTX P8S-GNSHX N/A P8S-GNMHX P8S-TMC /6" - 3/4" Bore P8S-GNFLX P8S-GNFTX P8S-GNSHX N/A P8S-GNMHX P8S-TMC /6" - -/" Bore P8S-GNFLX P8S-GNFTX P8S-GNSHX N/A P8S-GNMHX P8S-TMC /8" - -/" Bore P8S-GNFLX P8S-GNFTX P8S-GNSHX N/A P8S-GNMHX P8S-TMC " - 4" Bore P8S-GNFLX P8S-GNFTX P8S-GNSHX N/A P8S-GNMHX P8S-TMC All Bore Sizes P8S-GNFLX P8S-GNFTX P8S-GNSHX N/A P8S-GNMHX N/A 6 All Bore Sizes P8S-SNELX P8S-SNETX P8S-SNTHX N/A N/A N/A 8 Bracket Reference Page # 9/6" Bore L ** N/A L C N/A N/A N/A 3/4" - -/8" Bore L ** N/A L C N/A N/A N/A -/" - " Bore L ** N/A L C N/A N/A N/A -/" - 4" Bore L ** N/A L C N/A N/A N/A Tie Rod Cylinders MA/MAE/ MNR Series PD Series Standard & Clean Profiles PD Series Tie Rod Version All Bore Sizes P8S-GNFLX P8S-GNFTX P8S-GNSHX N/A P8S-GNMHX P8S-TMA0X 6 9 All Bore Sizes P8S-GNFLX P8S-GNFTX P8S-GNSHX P8S-GNSCX P8S-GNMHX N/A 6 All Bore Sizes P8S-GNFLX P8S-GNFTX P8S-GNSHX P8S-GNSCX P8S-GNMHX P8S-TMA0X 6 9 MP Series All Bore Sizes P8S-GNFLX P8S-GNFTX P8S-GNSHX N/A P8S-GNMHX P8S-TMA0X 6 9 Rodless Cylinders Linear Slides PY Series Standard Sensor All Bore Sizes P8S-GNFLX P8S-GNFTX P8S-GNSHX N/A P8S-GNMHX N/A 6 PY Series Short Sensor All Bore Sizes P8S-SNELX P8S-SNETX P8S-SNTHX N/A N/A N/A 8 RC Series All Bore Sizes L *** N/A L C N/A N/A N/A 3 P5T Series Flush Mount Type P8S-GNFLX P8S-GNFTX P8S-GNSHX N/A N/A N/A 6 Right Angle Type P8S-SNELX P8S-SNETX P8S-SNTHX N/A N/A N/A mm Bore P8S-GNFLX N/A P8S-GNSHX N/A N/A GSB- 6 C.F. P5E Series mm Bore P8S-GNFLX N/A P8S-GNSHX N/A N/A GSB- 6 C.F mm Bore P8S-GNFLX N/A P8S-GNSHX N/A N/A GSB-3 6 C.F. HB Series All Sizes P8S-GNFLX P8S-GNFTX P8S-GNSHX N/A P8S-GNMHX GSB- 6 C.F. XL Series Sizes 04 and 06 P8S-GNFLX P8S-GNFTX P8S-GNSHX N/A P8S-GNMHX P8S-TMC0 6 9 Sizes 08 and P8S-GNFLX P8S-GNFTX P8S-GNSHX N/A P8S-GNMHX P8S-TMC0 6 9 Rotary Actuators PV Series WR Series XR Series PTR Series Normally Open SMH-N** N/A SMH-NC N/A N/A N/A 4 Normally Open N/A N/A N/A N/A N/A N/A Normally Closed SMC-N** N/A SMC-NC N/A N/A N/A 4 Size 0 and 5 N/A SMH-N*** SWH-NC N/A N/A Included 6 Size 0, 5 and 3 N/A SMH-N*** SWH-NC N/A N/A Included 6 * Flying leads are meters in length ** Flying Leads are.5 meters in length *** Flying leads are meter in length Based on MA Cylinder C.F. = Consult Factory for dimensions. 3 Parker Hannifin Corporation

4 Selection Guide Reed Compact Cylinders Round Body Cylinders PA Series Standard Sensor PA Series Right Angle Sensor PL Series SRM/SRDM Series P Series All PM Series Standard Sensor All PM Series Short Sensor LPM Series 3 m Flying Leads Reed Sensor Selection Chart 0m Flying Leads 8 mm Quick Connect 8 mm Quick Connect w/ m Lead mm Quick Connect Bracket Sensor Reference Page # 0 mm Bore PA-XRL N/A PA-XSH N/A N/A PA-CCB 0 0 mm Bore PA-XRL N/A PA-XSH N/A N/A PA-DCB mm Bore PA-XRL N/A PA-XSH N/A N/A PA-FCB mm Bore PA-XRL N/A PA-XSH N/A N/A PA-HCB mm Bore PA-XRL N/A PA-XSH N/A N/A PA-JCB mm Bore N/A N/A N/A N/A N/A N/A mm Bore N/A N/A N/A N/A N/A N/A 6 mm Bore N/A N/A N/A N/A N/A N/A 0 mm Bore N/A N/A N/A N/A N/A N/A 5 mm Bore N/A N/A N/A N/A N/A N/A 0-5 mm Bore P8S-GRFLX P8S-GRFTX P8S-GRSHX N/A P8S-GRMHX P8S-TMC mm Bore P8S-GRFLX P8S-GRFTX P8S-GRSHX N/A P8S-GRMHX P8S-TMC mm Bore P8S-GRFLX P8S-GRFTX P8S-GRSHX N/A P8S-GRMHX P8S-TMC /6" - 3/4" Bore P8S-GRFLX P8S-GRFTX P8S-GRSHX N/A P8S-GRMHX P8S-TMC /6" - -/" Bore P8S-GRFLX P8S-GRFTX P8S-GRSHX N/A P8S-GRMHX P8S-TMC /8" - -/" Bore P8S-GRFLX P8S-GRFTX P8S-GRSHX N/A P8S-GRMHX P8S-TMC " - 4" Bore P8S-GRFLX P8S-GRFTX P8S-GRSHX N/A P8S-GRMHX P8S-TMC All Bore Sizes P8S-GRFLX P8S-GRFTX P8S-GRSHX N/A P8S-GRMHX N/A 7 All Bore Sizes P8S-SRELX P8S-SRETX P8S-SRTHX N/A N/A N/A 8 Bracket Reference Page # 9/6" Bore L ** N/A L C N/A N/A N/A 3/4" - -/8" Bore L ** N/A L C N/A N/A N/A -/" - " Bore L ** N/A L C N/A N/A N/A -/" - 4" Bore L ** N/A L C N/A N/A N/A Tie Rod Cylinders MA/MAE/ MNR Series PD Series Standard & Clean Profiles PD Series Tie Rod Version All Bore Sizes P8S-GRFLX P8S-GRFTX P8S-GRSHX N/A P8S-GRMHX P8S-TMA0X 7 9 All Bore Sizes P8S-GRFLX P8S-GRFTX P8S-GRSHX P8S-GRSCX P8S-GRMHX N/A 7 All Bore Sizes P8S-GRFLX P8S-GRFTX P8S-GRSHX P8S-GRSCX P8S-GRMHX P8S-TMA0X 7 9 MP Series All Bore Sizes P8S-GRFLX P8S-GRFTX P8S-GRSHX N/A P8S-GRMHX P8S-TMA0X 7 9 Rodless Cylinders Linear Slides PY Series Standard Sensor All Bore Sizes P8S-GRFLX P8S-GRFTX P8S-GRSHX N/A P8S-GRMHX N/A 7 PY Series Short Sensor All Bore Sizes P8S-SRELX P8S-SRETX P8S-SRTHX N/A N/A N/A 8 RC Series All Bore Sizes L *** N/A L C N/A N/A N/A 3 Flush Mount Type P8S-GRFLX P8S-GRFTX P8S-GRSHX N/A N/A N/A 7 P5T Series Right Angle Type P8S-SRELX P8S-SRETX P8S-SRTHX N/A N/A N/A mm Bore P8S-GRFLX N/A P8S-GRSHX N/A N/A GSB- 7 C.F. P5E Series mm Bore P8S-GRFLX N/A P8S-GRSHX N/A N/A GSB- 7 C.F mm Bore P8S-GRFLX N/A P8S-GRSHX N/A N/A GSB-3 7 C.F. HB Series All Sizes P8S-GRFLX P8S-GRFTX P8S-GRSHX N/A P8S-GRMHX GSB- 7 C.F. Sizes 04 and 06 P8S-GRFLX P8S-GRFTX P8S-GRSHX N/A P8S-GRMHX P8S-TMC0 7 9 XL Series Sizes 08 and P8S-GRFLX P8S-GRFTX P8S-GRSHX N/A P8S-GRMHX P8S-TMC0 7 9 Rotary Actuators PV Series WR Series XR Series PTR Series Normally Open SMR-^ N/A SMR-C # N/A N/A N/A 5 Normally Open SMR-L^^ N/A SMR-LC ## N/A N/A N/A 5 Normally Closed SMD-L^^ N/A SMD-LC ## N/A N/A N/A 5 Size 0 and 5 SWR-*** N/A SWR-C N/A N/A Included 7 Size 0, 5 and 3 SWR-*** N/A SWR-C N/A N/A Included 7 * Flying leads are meters in length ** Flying Leads are.5 meters in length *** Flying leads are meter in length # High Amp ## Low Amp ^ High Amp w/ Flying Leads.5 meters in length ^^Low Amp w/ Flying Leads.5 meters in length Based on MA Cylinder C.F. = Consult Factory 4 Parker Hannifin Corporation

5 Features Drop-In Parker is proud to present: The Global Drop-In Position Sensing Switches C086/A074 Both Reed and Solid State Sensor Versions Available World-Wide Solid State use GMR Technology 5 Different Connection Styles Allow Position Sensing Anywhere Along Cylinder Position The Same Sensor is Used On Virtually All Series of Cylinders CE Approved Defined by Part Number: P8S-G 5 Parker Hannifin Corporation

6 Solid State Sensor Specifications Drop-In Drop-In Solid State Sensor Part Numbers C086/A074 PNP Wiring NPN Wiring P8S-GPFLX 3m flying leads P8S-GNFLX 3m flying leads P8S-GPFTX 0m flying leads P8S-GNFTX 0m flying leads P8S-GPSHX.m lead with 8mm connector P8S-GNSHX.m lead with 8mm connector P8S-GPMHX.m lead with mm connector P8S-GNMHX.m lead with mm connector P8S-GPSCX m lead with 8mm connector P8S-GNSCX m lead with 8mm connector SOLID STATE SENSOR SPECIFICATIONS Type... Electronic Output Function... Normally Open Switching Output... PNP/NPN Operating Voltage VDC Continuous Current ma max.* Response Sensitivity....8 mt min. Switching Frequency... 5 KHz Power Consumption... 0 ma max. Voltage Drop... VDC max. Ripple... 0% of Operating Voltage Hysteresis....5 mm max. Repeatability mm max. EMC... EN Short-circuit Protection... Yes Power-up Pulse Suppression... Yes Reverse Polarity Protection... Yes Enclosure Rating... IP 67 Shock and Vibration Stress... 30g, ms, 0 to 55 Hz, mm Operating Temperature Range C to +75 C (-3 F to 67 F) Housing Material... PA, Black Connector Cable... PVC Connector... PUR cable w/8 or mm conn. *M connector is rated for 00 ma maximum continuous current. SOLID STATE SWITCH - WIRING CONNECTION Flying Lead or 8 mm Connector (shown) 3 Pin Wire Function Brown Operating Voltage Black Output signal 3 Blue 0V 3 4 mm Connector PIN Wire Function brown Operating Voltage 4 black Not used white Output Signal 3 blue 0V PNP NPN bn bn +VDC +VDC PNP NPN wh wh bk bk bu bn 3 +VDC bu 3 bn +VDC 3 -VDC 3 bu bu -VDC bk Not Used -VDC bk Not Used -VDC 6 Parker Hannifin Corporation

7 Reed Sensor Specifications Drop-In Drop-In Reed Sensor Part Numbers C086/A074 REED P8S-GRFLX P8S-GRFTX P8S-GRSHX P8S-GRMHX P8S-GRSCX Wiring 3m flying leads 0m flying leads.m lead with 8mm connector.m lead with mm connector m lead with 8mm connector REED SENSOR SPECIFICATIONS Type...Reed Output Function...Normally Open Operating Voltage VAC* VDC Continuous Current...00 ma max. Response Sensitivity...5 mt min. Switching Frequency Kz Voltage Drop...3 V max. Ripple...0% of Operating Voltage Hysteresis...5 mm max. Repeatability...0. mm max. EMC...EN Reverse Polarity Protection...Yes Enclosure Rating...IP 67 Shock and Vibration Stress...30g, ms, 0 to 55 Hz, mm Operating Temperature Range...-5 C to +75 C (-3 F to 67 F) Housing Material...PA, Black Connector Cable...PVC Connector...PUR cable w/8 or mm conn. *8mm connector rated for 75 VAC max. REED SENSOR - WIRING CONNECTION Flying Lead or 8 mm Connector Pin Wire Function Brown Operating Voltage Black Output signal 3 Blue Not used mm Connector Pin Wire Function Brown Operating Voltage White Output signal 3 Blue Not used 4 Black Not used Circuit for Switching Contact Protection (Inductive Loads) (Required for proper operation 4V DC) Put Diode parallel to loads following polarity as shown below. Brown Blue Load D: Diode: select a Diode with the breakdown voltage and current rating according to the load. Typical Example 00 Volt, Amp Diode CR: Relay coil (under 0.5W coil rating) D DC (Recommended for longer life 5 VAC) Put a resistor and capacitor in parallel with the load. Select the resistor and capacitor according to the load. Typical Example: CR: Relay coil (under W coil rating) R: Resistor KΩ - 5 KΩ, /4 W C: Capacitor 0. µf, 600 V Brown Blue Load R C AC! Caution Use an ampmeter to test reed switch current. Testing devices such as incandescent light bulbs may subject the reed switch to high in-rush loads. NOTE: When checking an unpowered reed switch for continuity with a digital ohmmeter the resistance reading will change from infinity to a very large resistance ( M ohm) when the switch is activated. This is due to the presence of a diode in the reed switch. Anti-magnetic shielding is recommended for reed switches exposed to high external RF or magnetic fields. The magnetic field strength of the piston magnet is designed to operate with our switches. Other manufacturers switches or sensors may not operate correctly in conjunction with these magnets. Use relay coils for reed switch contact protection. The operation of some 0 VAC PLC s (especially some older Allen-Bradley PLC s) can overload the reed switch. The switch may fail to release after the piston magnet has passed. This problem may be corrected by the placement of a 700 to K OHM resistor between the switch and the PLC input terminal. Consult the manufacturer of the PLC for appropriate circuit. Switches with long wire leads (greater than 5 feet) can cause capacitance build-up and sticking will result. Attach a resistor in series with the reed switch (the resistor should be installed as close as possible to the switch). The resistor should be selected such that R (ohms) >E/ Parker Hannifin Corporation

8 Sensor Specifications Slide-In Short C086/A074 SOLID STATE SENSOR SPECIFICATIONS Type... Electronic Output Function... Normally Open Switching Output... PNP/NPN Operating Voltage VDC Continuous Current ma Response Sensitivity... 3 mt Switching Frequency... 5kHz Power Consumption... 5 ma Voltage Drop... VDC Ripple... 0% of Operating Voltage Delay Time (4V)... Approx. 0 ms Time Delay before Availability. ms Hysteresis....5 mm Repeatability mm EMC... EN Short-circuit Protection... Yes Power-up Pulse Supression... Yes Reverse Polarity Protection... Yes Enclosure Rating... IP 67 DIN Shock and Vibration Stress... 30g, ms, 0 to 55 Hz, mm Ambient Temperature Range C to +75 C (-3 F to 67 F) Housing Material... PA, Black Connector Cable... PVC Connector... PUR cable w/8 mm connector WIRING CONNECTION 3 3 Pin Wire Function Brown Operating Voltage Black Output signal 3 Blue 0V Sensor Part No. Type Wiring P8S-SPTHXD PNP.7m lead with connector P8S-SPELXD PNP 3m flying leads P8S-SPETXD PNP 0m flying leads P8S-SNTHX NPN.7m lead with connector P8S-SNELX NPN 3m flying leads P8S-SNETX NPN 0m flying leads REED SENSOR SPECIFICATIONS Type... Reed Output Function... Normally Open Output Voltage * VAC VDC Continuous Current ma Response Sensitivity mt Switching Frequency Hz Voltage Drop... 3 V Ripple... 0% of Operating Voltage Time Delay (4V)... Approx. 0 ms Hysteresis....0 mm Repeatability mm EMC... EN Reverse Polarity Protection... Yes Enclosure Rating... IP 67 Shock and Vibration Stress... 30g, ms, 0 to 55 Hz, mm Ambient Temperature Range C to +75 C (-3 F to 67 F) Housing Material... PA, Black Connector Cable... PVC Connector... PUR cable w/8 mm connector *8mm connector rated for 75 VAC max. 3 WIRING CONNECTION Pin Wire Function Brown Operating Voltage Black Output signal 3 Blue Not Used Sensor Part Number Type Wiring P8S-SRTHX REED.7m lead with connector P8S-SRELX REED 3m flying leads P8S-SRETX REED 0m flying leads 8 Parker Hannifin Corporation

9 Bracket Specifications P8S Sensor Accessories Round Body Bracket Dimensions C086/A Round Body Bracket Assembly Part Numbers and Brackets must be ordered separately. Bore Size Round Body Bracket 9 /6"-.06" P8S-TMC0 0-5mm P8S-TMC0 /8"-.5" P8S-TMC0 3-63mm P8S-TMC0 3"-4" P8S-TMC mm P8S-TMC03 Tie Rod Bracket Dimensions Tie Rod Bracket Part Number and Brackets must be ordered separately. Tie Rod Clamp Assembly P8S-TMA0X 9 Parker Hannifin Corporation

10 Sensor Specifications Reed The reed switch sensors incorporate a well-proven, universal-voltage, compact reed switch element; making them suitable for a wide range of applications. They can work with electronic control systems or conventional relay systems. Technical Data Design Reed Output Making Voltage range, PA-XRL 0 VAC/VDC Voltage range, PA-XSH 60 VAC/VDC Max voltage drop,8 V Max load current 80 ma Max breaking power (resistive) 0 W Min actuating distance 5 mm Hysteresis mm Repeatability accuracy ±0, mm Max on/off switching frequency 500 Hz Max on/off switching time ms Encapsulation, PA-XRL IP 67 Encapsulation, PA-XSH IP 65 Temperature range 30 C to +80 C ( F to 76 F) Indication LED Shock resistance 30 g Material, housing Nylon 66 Material, mould Epoxy Cable PVC x0, mm Cable incl. female part connector PVC x0, mm Mounting Mounting yoke Material, mounting Stainless steel Material, screw Stainless steel Connector Diam. 8 mm snap on Ordering Data Order code Cylinder Output Cable Weight bore mm length Lbs. Reed sensors PA-XRL 0-5 making 3 m. PA-XSH 0-5 making *.004 Mountngs for sensors PA-CCB PA-DCB.005 PA-FCB PA-HCB PA-JCB 5.0 Cable for sensors ** 3 m ** 0 m.4 *) Cable shall be ordered separately. **) Cable including female part connector, for sensor. PA Series Solid State These sensors are of solid-state type, with no moving parts. Shortcircuit and transient protection is incorporated as standard. The integral electronics make these sensors suitable for applications with very high switching frequencies. Technical Data Design Hall element Output PNP resp. NPN, N.O. Voltage range 0-30 VDC Max permissible ripple 0% Max voltage drop 0,5 V at 00 ma Max load current, PA-XMK, LK 50 ma PA-XHK, EK, JH, FH 00 ma Max breaking power (resistive) 6 W Internal consumption <30 ma at 30 V Min actuating distance 5 mm Hysteresis, -,3 mm Repeatability accuracy ±0, mm Max on/off switching frequency khz Max on/off switching time 0,8/3,0 ms Encapsulation, PA-XJH, FH IP 65 Encapsulation, PA-XHK, EK, MK, LK IP 67 Temperature range 0 C to +60 C (4 F to 40 F) Indication LED Shock resistance 40 g Material, housing Polyamid Material, mould Epoxy Cable PVC 3x0,5 mm Cable incl. female part connector PVC 3x0,5 mm Connector Diam. 8 mm snap on Mounting Mounting yoke Material, mounting Acetal/Stainless steel Material, screw Stainless steel Ordering Data Order code Cylinder Output Cable Weight bore mm length Lbs. Electronic sensors PA-XMK, PNP, N.O. m.09 PA-XLK, NPN, N.O. m.09 PA-XHK 0-5 PNP, N.O. m.0 PA-XEK 0-5 NPN, N.O. m.0 PA-XJH 0-5 PNP, N.O. *.033 PA-XFH 0-5 NPN, N.O. *.033 Mountngs for sensors PA-CCC 0.0 PA-DCC.0 PA-FCC PA-HCC PA-JCC 5.0 Cable for sensors ** 3 m ** 0 m.4 C086 Reed Sensor Symbol Solid State Sensor Symbol PA-XMK PA-XLK Brown Blue White PA-XHK,PA-XJH Black Red Black Brown Blue White PA-XEK, PA-XFH Black Black Red Blue Brown 0 Parker Hannifin Corporation

11 Dimensions Dimensions Reed PA-XRL PA Series PA-XSH C086 Solid State PA-XHK and PA-XEK LED 3 x 0,5 mm, m LED PA-XJH and PA-XFH 3,8 3, PA-XMK and PA-XLK LED ,5 x 0, mm, 3 m 3,5 Connector diam. 8, snap on Connector diam. 8, snap on 3 x 0,5 mm, m 9 Parker Hannifin Corporation

12 Sensor Specifications LP/LPM Series Sensor Specifications Part Numbers* Bore Reed (Low AMP) NPN Sinking PNP Sourcing 9 /6" L L L / 4", / 8" L L L / ", " L L L / ", 3", 4" L L L * For sensors with an 8mm connector, replace the last digit with a C. C086 Model Number Reed Sensor (Low AMP) NPN PNP Switching Logic N.O. SPST (Form A) N.O. NPN (Sinking) N.O. PNP (Sourcing) Supply Voltage Range 3-5 V AC/DC 5-30 VDC On-State Voltage Drop.8V max. at 0 ma DC.5 V max. at 00 ma Current Output Range 00 ma Burden Current 7 ma at V 4 ma at 4 V Power Rating* 5 W (.5 W) 5 VA (.5 VA) Switching Current Range* 5-40 ma (5-0 ma) Leakage Current ma LED Function Red (Target Present) Red (Target Present) Green (Target Present) Minimum Current to Light LED 3 ma ma ma Operating Temperature 4 to 58 F (-0 to 70 C) 4 to 58 F (-0 to 70 C) Storage Temperature -4 to 76 F (-0 to 80 C) -4 to 76 F (-0 to 80 C) Enclosure Protection IEC standard IP 67 NEMA 6P Lead Wire conductor, 4 gauge 3 conductor, 4 gauge Lead Wire Length 59 inches,.5 meter Color of Cable Gray Black Switching Response Max. 300 Hz Max. k Hz Shock Resistance 30 G (300 m/s ) 50 G (490 m/s ) Vibration Resistance Double Amplitude.5 mm (Frequency 0 to 55 Hz scanning, minute) *Number in parentheses pertains to inductive loads. Circuits Reed Sensor NOTE: Polarity must be observed for DC operation only. Brown Blue Load DC or AC NPN Sinking Output Color of Cable... Black On State Voltage Drop...5V Maximum Brown (Red*) Black (White*) Blue (Black*) (+) 5 to 30 VDC ( ) PNP Sourcing Output Color of Cable... Black On State Voltage Drop...5V Maximum Brown (Red*) Black (White*) Blue (Black*) (+) 5 to 30 VDC ( ) Circuit for Switching Contact Protection (Inductive Loads) for Reed Sensor Only (Required for proper operation 4V DC) Put Diode parallel to loads following polarity as shown below. Brown Blue Load D: Diode: select a Diode with the breakdown voltage and current rating according to the load. Typical Example 00 Volt, Amp Diode CR: Relay coil (under 0.5W coil rating) D DC (Recommended for longer life 5 VAC) Put a resistor and capacitor in parallel with the load. Select the resistor and capacitor according to the load. Typical Example: CR: Relay coil (under W coil rating) R: Resistor KΩ 5 KΩ, /4 W C: Capacitor 0. µf, 600 V Brown Blue Load R C AC! Caution Use an ampmeter to test reed switch current. Testing devices such as incandescent light bulbs may subject the reed switch to high in-rush loads. NOTE: When checking an unpowered reed switch for continuity with a digital ohmmeter the resistance reading will change from infinity to a very large resistance ( M ohm) when the switch is activated. This is due to the presence of a diode in the reed switch. Anti-magnetic shielding is recommended for reed switches exposed to high external RF or magnetic fields. The magnetic field strength of the piston magnet is designed to operate with our switches. Other manufacturers switches or sensors may not operate correctly in conjunction with these magnets. Current capabilities are relative to operational temperatures. Use relay coils for reed switch contact protection. The operation of some 0 VAC PLC's (especially some older Allen-Bradley PLC's) can overload the reed switch. The switch may fail to release after the piston magnet has passed. This problem may be corrected by the placement of a 700 to K OHM resistor between the switch and the PLC input terminal. Consult the manufacturer of the PLC for appropriate circuit. Switches with long wire leads (greater than 5 feet) can cause capacitance build-up and sticking will result. Attach a resistor in series with the reed switch (the resistor should be installed as close as possible to the switch). The resistor should be selected such that R (ohms) >E/0.3. Parker Hannifin Corporation

13 Sensor Specifications RC Series RC Series Sensor Specifications C347 Reed Sensor AssemblySolid State Sensor Assembly L L NPN Sinking L PNP Sourcing Switching Logic Normally open, SPST (Form A) NPN or PNP Supply Voltage Range 85 to 5 VAC or 5-30 VDC 0-30 VDC On-State Voltage Drop.7 V Maximum See Circuits Below Current Output Range Up to 00 ma at VDC Up to 00 ma at 4 VDC Burden Current 7 ma at VDC 6 ma at 4 VDC Power Rating 0 Watts (Resistive) 5 Watts (Capacitive) Switching Current Range 30 ma to 00 ma (Resistive) 30 ma to 00 ma (Capacitive) Leakage Current 0 0µA LED Function Red, Target Present Red, Target Present Minimum Current to Light LED 8 ma ma Reed Sensor Assembly Solid State Sensor Assembly L L NPN Sinking L PNP Sourcing Operating Temperature 4 to 40 F (-0 to 60 C) 4 to 40 F (-0 to 60 C) Storage Temperature -4 to 40 F (-0 to 60 C) -4 to 58 F (-0 to 70 C) Enclosure Protection Nema 6, IEC IP67 Nema 6, IEC IP67 Lead Wire conductor, 4 Gauge 3 conductor, 4 Gauge Lead Wire Length 39 Inches, Meter 39 Inches, Meter Color of Cable Black See Below Switching Response 300 Hz Maximum 000 Hz Maximum Shock Resistance 30g not applicable Vibration Resistance 0-55 Hz,.5 mm not applicable Double Amplitude Polarity is restricted to DC operation: (+) to Brown (White*) (-) to Blue (Black*) If these connections are reversed the contacts will close, but the LED will not light. Circuits Reed Sensor Part No.... L NOTE: Polarity must be observed for DC operation only. Brown Blue Load DC or NPN Sinking Output Part No.... L Color of Cable... Black On State Voltage Drop V Maximum AC Brown (Red*) Black (White*) Blue (Black*) (+) 5 to 30 VDC *Wire colors in parentheses pertain to switches manufactured before 0/5/93. ( ) PNP Sourcing Output Part No.... L Color of Cable... Gray On State Voltage Drop... 0.V Maximum Brown (Red*) Black (White*) Blue (Black*) (+) 5 to 30 VDC ( ) Circuit for Switching Contact Protection (Inductive Loads) (Required for proper operation 4V DC) Put Diode parallel to loads following polarity as shown below. Put a resistor and capacitor in parallel with the load. Select the resistor and capacitor according to the load. Brown Load D DC Typical Example: CR: Relay coil (under W coil rating) R: Resistor KΩ 5 KΩ, /4 W C: Capacitor 0. µf, 600 V Brown Load R C AC Blue Blue D: Diode: select a Diode with the breakdown voltage and current rating according to the load. Typical Example 00 Volt, Amp Diode CR: Relay coil (under 0.5W coil rating) (Recommended for longer life 5 VAC) -3/4" 9/3"! Caution Use an ampmeter to test reed switch current. Testing devices such as incandescent light bulbs may subject the reed switch to high in-rush loads. NOTE: When checking an unpowered reed switch for continuity with a digital ohmmeter the resistance reading will change from infinity to a very large resistance ( M ohm) when the switch is activated. This is due to the presence of a diode in the reed switch. Anti-magnetic shielding is recommended for reed switches exposed to high external RF or magnetic fields. The magnetic field strength of the piston magnet is designed to operate with our switches. Other manufacturers switches or sensors may not operate correctly in conjunction with these magnets. Current capabilities are relative to operational temperatures. Use relay coils for reed switch contact protection. The operation of some 0 VAC PLC's (especially some older Allen-Bradley PLC's) can overload the reed switch. The switch may fail to release after the piston magnet has passed. This problem may be corrected by the placement of a 700 to K OHM resistor between the switch and the PLC input terminal. Consult the manufacturer of the PLC for appropriate circuit. Switches with long wire leads (greater than 5 feet) can cause capacitance build-up and sticking will result. Attach a resistor in series with the reed switch (the resistor should be installed as close as possible to the switch). The resistor should be selected such that R (ohms) >E/ Parker Hannifin Corporation

14 Sensor Specifications Solid State (Hall Effect) Switches PV, WR & XR Series 6" cord A076 Part Numbers Part No. Type LED Color Logic Cable/Connector SMH-P N.O. Green PNP SMH-N N.O. Red NPN.5 m Black SMC-P N.C. Yellow PNP with Leads SMC-N N.C. White/Red NPN SMH-PC N.O. Green PNP SMH-NC N.O. Red NPN 50 mm Black SMC-PC N.C. Yellow PNP with Connector SMC-NC N.C. White/Red NPN BROWN 4 BLACK 3 BLUE WIRING CONNECTION 60" cord BROWN + Specifications PNP SWITCH BLACK 6-30VDC Type... Solid State Type (PNP or NPN) Switching Logic... Normally Open or Normally Closed Supply Voltage Range VDC Max. Switch Current ma Current Consumption... 7 ma at VDC, 4 ma at 4 VDC Switching Response Hz Maximum Residual Voltage V Maximum (50 ma) Leakage Current... 0 ua Maximum Insulation Resistance M ohm min. Min. Current for LED... ma Operating Temperature to 85 C (4 to 85 F)** Lead Termination mm (60 in) or 50 mm (6 in) with connector Industrial Protection... IP67 Shock Resistance G's, 490 m/sec NPN SWITCH SWITCH BLUE BROWN BLACK BLUE PROTECTION CIRCUIT* BROWN BLACK _ VDC _ + BLUE _ * When connecting an inductive load (relay, solenoid valve, etc.), a protection circuit is recommended. Use a 00V, A diode. (NPN connection shown.) 4 Parker Hannifin Corporation

15 Sensor Specifications Reed Switches Reed switches are available in a normally open or normally closed configuration. The low amp switch is suitable for connection to PLCs or other low current devices. The high amp switch can be used to drive sequencers, relays, coils, or other devices directly. Part Numbers Part No. Type LED Color Rating Cable/Connector SMR- N.O. Green High Amp SMR-L N.O. Red Low Amp SMD-L N.C. Yellow Low Amp SMR-C N.O. Green High Amp SMR-LC N.O. Red Low Amp SMD-LD N.C. Yellow Low Amp.5 m Grey with Leads 50mm Grey with Connector Integral Circuit for Switching Contact Protection (Required for proper operation 4V DC) Put Diode parallel to load (CR) with polarity as shown below. + VDC - D: Diode: select a Diode with the breakdown voltage and current rating according to the load. CR: Relay coil (under 0.5 W coil rating) (Recommended for longer switch life 5V AC) Put resistor and capacitor parallel to load (CR). + 5VAC - (BROWN) (BROWN) CR: Relay coil (under W coil ratings) R: Resistor under K ohm C: Capacitor 0. µf D R C (BLUE) (BLUE) CR CR PV, WR & XR Series SMR-L or SMD-L Low Amp Reed Switch Specifications Switching Logic... Normally Open (SMR-L) Normally Closed (SMD-L) Voltage Rating VAC or 6-30 VDC* (N.O.) 6-30 VAC, 6-30 VDC* (N.C.) Power Rating: AC or DC Resistive Load... 0 watts (N.O.) AC or DC Inductive Load... 5 watts (N.O.) AC or DC... 3 watts (N.C.) Switching Current Range: Resistive Load (PC, Sequencer) ma (N.O.), 5-5 ma (N.C.) Inductive Load (Relay) ma Minimum Current for LED... 5 ma Switching Response Hz (N.O.), 00 Hz (N.C.) Breakdown Voltage VDC Contact Resistance M ohm min. Operating Temperature to 85 C (4 to 85 F) Lead Termination mm (60 in) or 50 mm (6 in) with connector Industrial Protection... IP67 Shock Resistance G's, 300 m/sec SMR- High Amp Reed Switch Specifications Switching Logic... Normally Open Voltage Rating VAC or 5-30 VDC* Power Rating: AC or DC Resistive Load... 0 watts AC or DC Inductive Load... 5 watts Switching Current Range: Resistive Load (PC, Sequencer) ma Inductive Load (Relay) ma Minimum Current for LED... 8 ma Switching Response Hz Maximum Breakdown Voltage VDC Contact Resistance M ohm min. Operating Temperature to 85 C (4 to 85 F) Lead Termination mm (60 in) or 50 mm (6 in) with connector Industrial Protection... IP67 Shock Resistance G's, 300 m/sec * Polarity is restricted for DC operation (+) to Brown (-) to Blue If these connections are reversed the contacts will close, but the LED will not light. Note: Care must be taken not to exceed the Power Rating of the switch while still observing the voltage and current limitations. A076 5 Parker Hannifin Corporation

16 Sensor Specifications PTR Series Solid State (Hall Effect) 6"cord A076 Part Numbers PNP NPN Model With 6" With 39" With 6" With 39" Male Quick Potted-in Male Quick Potted-in Connect Leads Connect Leads 0 SWH-PC SWH-P SWH-NC SWH-N 5 SWH-PC SWH-P SWH-NC SWH-N 0 SWH-PC SWH-P SWH-NC SWH-N 5 SWH-PC SWH-P SWH-NC SWH-N 3 SWH-PC SWH-P SWH-NC SWH-N BROWN 4 BLACK 3 BLUE 39"Cord Note: Switches with male quick connect option require female cordsets to be ordered separately. See page 8. WIRING CONNECTION BROWN + Specifications Type... Solid State (PNP or NPN) Switching Logic... Normally Open Supply Voltage Range VDC Current Output Range.. Up to00 ma at 5 VDC, Up to 00 ma at VDC and 4 VDC Current Consumption... 7 ma at 5 VDC, 5 ma at VDC, and 30 ma at 4 VDC Switching Response Hz Maximum Residual Voltage....5V Maximum Leakage Current... 0uA Maximum Breakdown Voltage....8kVACrms for sec., lead to case Min. Current for LED... ma Operating Temperature. 4 to 40 F (-0 to 60 C) Enclosure Protection... Meets IEC IP67, fully encapsulated Lead Wire... 3 conductor, 4 gauge Lead Wire Length in ( m) Vibration Resistance Hz,.5mm double amplitude PNP NPN BLACK SWITCH BLUE BROWN BLACK SWITCH BLUE PROTECTION CIRCUIT* BROWN BLACK SWITCH BLUE 6-30VDC _ VDC _ + _ * When connecting an inductive load (relay, solenoid valve, etc.), a protection circuit is recommended. Use a 00V, A diode. (NPN connection shown.) 6 Parker Hannifin Corporation

17 Sensor Specifications PTR Series Reed Switches A076 Part Numbers With 6" With 39" Model Male Quick Potted-in Connect Leads 0 SWR-C SWR- 5 SWR-C SWR- 0 SWR-C SWR- 5 SWR-C SWR- 3 SWR-C SWR- Note: Switches with male quick connect option require female cordsets to be ordered separately. See page 8. Specifications Switching Logic... Normally Open Voltage Rating VAC or 6-30 VDC* Power Rating... 0 Watts AC or DC/Resistive Load 5 Watts AC or DC/Inductive Load Switching Current Range 0-00 ma/resistive Load (PC, Sequencer) 0-00 ma/inductive Load (Relay) Switching Response Hz Maximum Breakdown Voltage....8kVACrms for sec., lead to case Min. Current for LED... 8mA Operating Temperature... 4 to 40 F (-0 to 60 C) Enclosure Protection... Meets IEC IP67, fully encapsulated Lead Wire... conductor, Gauge Lead Wire Length in ( m) Vibration Resistance Hz,.5mm double amplitude 5VAC PROTECTION CIRCUIT (INDUCTIVE S) (Required for proper operation 4VDC) Select a diode with a breakdown voltage and current rating according to the load. Place a diode in parallel to the load with the polarity as indicated: BROWN 4VDC BLUE - (Recommended for longer switch life 5VAC) Select a resistor and capacitor according to the load. Place a resistor and capacitor in parallel to the load: BROWN BLUE D CR: Relay coil (under 0.5W coil rating) R C = = CR: Relay coil (under W coil rating) R: Resistor under K ohm C: Capacitor 0. µf CR CR * Polarity is restricted for DC operation (+) to White (-) to Black If these connections are reversed the contacts will close, but the LED will not light. 7 Parker Hannifin Corporation

18 Cordset Specifications 8mm Cordset with Female Quick Connect A female connector is available for all sensors with the male 8mm quick connect option. The male plug will accept a snapon or threaded connector. Cordset part numbers are listed below: Threaded Snap-On Cable Length Connector Connector 5 meters 08660T S005 meters 08660T S00 Sensor Accessories Cordset Specifications: Connector: Contacts: Coupling Method: Cord Construction: Conductors: Temperature: Protection: Cable Length: C086/A074/A076 Oil resistant polyurethane body material, PA 6 (Nylon) contact carrier, spacings to VDE 00 Group C, (50 AC/DC) Gold plated beryllium copper, machined from solid stock Snap-Lock or chrome plated brass nut Oil resistant black PUR jacket, nonwicking, non-hygroscopic, 300V. Cable end is stripped and tinned. Extra high flex stranding, PVC insulation -40 to 94 F (-40 to 90 C) NEMA, 3, 4, 6P and IEC P ft (m) or 6.4 ft (5m) Snap-On Straight Connector Threaded Straight Connector CABLE LENGTH (m) (SEE TABLE) CABLE LENGTH (m) (SEE TABLE) M8x Ø Ø Ø CABLE MINIMUM BEND RADIUS: 00mm Ø Ø CABLE MINIMUM BEND RADIUS: 00mm mm Cordset with Female Quick Connect M Straight Connector Cable Length Part Number 5 meters meters A female connector is available for all sensors with the male mm quick connect option. The cordsets are available with a right angle or straight connector. Cordset part numbers are listed above. Cordset Specifications: Connector: Contacts: Coupling Method: Cord Construction: Conductors: Temperature: Protection: Cable Length: Polyvinylchloride (PVC) body material, PVC contact carrier, spacing to VDE 00 Group C, (50VAC / 300VDC) Gold Plated Copper Tin (CuSn), stamped from stock. Threaded nut: Chrome plated brass. PVC non-wicking, non-hygroscopic, 50VAC / 300VDC. Cable end is stripped. Extra high flex stranding with PVC insulation -3 F to 58 F (-5 C to 70 C) NEMA, 3, 4, 6P and IEC P ft (m) or 6.4 ft (5m) PIN / WHT PIN 3 / BLU Ø4.5 CABLE LENGTH (m) (SEE TABLE) M X PIN 4 / BLK CABLE MINIMUM BEND RADIUS: 00mm PIN / BRN Ø4.5 PIN / BRN M Right Angle Connector Cable Length Part Number 5 meters meters Straight Connector PIN 4 / BLK PIN / WHT PIN 3 / BLU 4 Right Angle Connector CABLE MINIMUM BEND RADIUS: 00mm CABLE LENGTH (SEE TABLE) M X 8 Parker Hannifin Corporation

19 Connection Box Connection Block Valvetronic 0 The Valvetronic 0 is a connection block that can be used for collecting signals from sensors at various points on a machine and connecting them to the control system via a multicore cable. Valvetronic 0 can also be used for central connection of the multi-core cable to the outputs of a control system, and can be laid to a machine where the output signals can be connected. The connection block has ten 8 mm snap-in circular connectors and a multi-core cable which is available in lengths of 3 or 0 m. The connections on the block are numbered from to 0. Blanking plugs are available for unused connections, as labels for marking the connections of each block. Technical Data Connections: Ten 3-pole numbered 8 mm round snap-in female contacts 3 3 Ordering Data Input block Pin Common, +4 VDC Pin Input signal Pin 3 Common, 0V Output block Pin Common, GND Pin Output signal Pin 3 Common, 0V Electrical Data: Voltage 4 VDC (max. 60 V AC/75 V DC) Insulation group according to DIN 00 class C Load max. A per connection total max. 3 A Cable: Length 3 m or 0 m Type of cable LifYYY Conductor Area 0.34 mm Color marking According to DIN Sensor Accessories Mechanical Data Enclosure Temperature 0 C to +70 C IP 67, DIN with fitted contacts and/or blanking plugs. Material Body PA 6,6 VD according to UL 94 Contact holder PBTP Snap-in ring LDPE Moulding mass Epoxy Seal NBR Screws Plated steel Industrial Durability Good chemical and oil resistance. Tests should be performed in aggressive environments. C086 Order code Designation Weight kg Connection block Valvetronic 0 with 3 m cable 0, Connection block Valvetronic 0 with 0 m cable 0, Blanking plugs (pack of 0) 0,0 Use blanking plugs to close unused connections Labels (pack of 0) 0,0 White labels to insert in grooves on the side of the connection Dimensions and Wiring Diagrams ,7,5 8 5 M , 0,5 30,5 L A B Conductor Colour Input Output Pink Signal Signal Grey Signal Signal 3 Yellow Signal 3 Signal 3 4 Green Signal 4 Signal 4 5 White Signal 5 Signal 5 6 Red Signal 6 Signal 6 7 Black Signal 7 Signal 7 8 Violet Signal 8 Signal 8 9 Grey-Pink Signal 9 Signal 9 0 Red-Blue Signal 0 Signal 0 A Blue 0 V 0 V B Brown +4 V PE 9 Parker Hannifin Corporation

20 Dimensional Information EPS 7 & 6 Cylinder End-of-Stroke Proximity CLS & 4 C A C A C.00 EPS 5 Automotive Applications 9 / 6 / 3 7 / 3 (Meets some Automotive Manufacturer s Specifications) 3 / 8 7/ 8 7/ 8 A C Series and Parallel Wiring When Parker EPS-5, 6 or 7 proximity switches are used as inputs to programmable controllers the preferred practice is to connect each switch to a separate input channel of the PC. Series or parallel operations may then be accomplished by the internal PC programming. Parker EPS-5, 6 or 7 switches may be hard wired for series operation, but the voltage drop through the switches (see specifications) must not reduce the available voltage below what is needed to actuate the load. Parker EPS-5, 6 or 7 switches may also be hard wired for parallel operation. However, the leakage current of each switch will pass through the load. The total of all leakage currents must not exceed the current required to actuate the load. In most cases, the use of two or more EPS-5, 6 or 7 switches in parallel will require the use of a bypass (shunt) resistor. Series A max. C max. A.55".30" For exact dimensions, see Bulletin 0840-G-E Connector Pin Numbering 3-Pin Mini 5-Pin Mini 0 Parker Hannifin Corporation

21 Specifications Cylinder End-of-Stroke Proximity C05 Specifications Style: EPS- 7 EPS- 5 EPS- 6 CLS- CLS- 4 Code Designator: H R D F B Description: Economical, General Purpose, wire device, primarily for AC applications, not suitable for 4 VDC applications. Use EPS-5 only for automotive industry customers who specify them. Economical, General Purpose, 3 wire, DC sensor, dual output: sinking and sourcing Functional replacement for AB (Mechanical) Limit Switches in many applications, or where customer needs NC contacts, zero leakage, zero voltage drop, higher or lower load current than EPS-style. Functional replacement for AB (Mechanical) Limit Switches in many High Temperature applications, or where customer needs NC contacts, zero leakage, zero voltage drop, higher or lower load current than EPS-style. Supply Voltage: 0 to 50 VAC/DC 0 to 30 VAC/DC 0 to 30 VDC 4 to 40 VAC/DC 4 to 40 VAC/DC Load Current, min: 8 ma 5 ma NA NA NA Load Current, max: 300 ma 500 ma 00 ma 4 0 VAC 3 4 VDC 4 0 VAC 3 4 VDC Leakage Current:.7 ma, max..7 ma, max. 0 micro amps max. - - Voltage Drop: 7 V, max. 0 V, max VDC max. NA NA Operating Temperature: -4 to +58 F -4 to +58 F -4 to +58 F -40 F to + F -40 F to +400 F Sensor Type: Inductive proximity Inductive proximity Inductive proximity Non-contacting magnetically actuated Non-contacting magnetically actuated Part Number: 48897**** 4667**** 48896**** 4875**** 4909**** Part Number Suffix **** : **** 4-digit suffix indicates probe length: 05=.5", 006=.06", 088=.875", 0456=4.56" Connection: 3 pin mini 3 pin mini 5 pin mini 3 pin mini 44" PTFE Coated Flying Leads with /" conduit hub Enclosure Rating: IEC IP67 NEMA 4, 6,, 3 IEC IP67 NEMA,, 3, 4, 4x, 5, 6, 6P,,, K, 3 NEMA,, 3, 4, 4x, 5 LED indication: Yes Yes Yes No No Short Circuit Protection: Yes Yes Yes No No Weld Field I mmunity: Yes Yes Yes Yes Yes Output: wire, Normally Open with leakage current wire, Normally Open with leakage current Dual output: DC Sinking and DC Sourcing, user selectable via wiring SPDT (Single Pole Double Throw), Normally Open/Normally Closed, Form C SPDT (Single Pole Double Throw), Normally Open/Normally Closed, Form C Approvals/ Marks: CE, UL, CSA UL CE, UL, CSA UL or CSA UL or CSA Make/ Break Location 0.5" from end of stroke, typical. Tolerance is 0/-.5" Pin : AC Ground (Green) Pin : AC Ground (Green) Pin ) +0 to 30 VDC (White) Pin : Common (Green) Common: (Black) Pin : Output (Black) Pin : Output (Black) Pin ) Sourcing Output (Red) Pin : Normally Closed (Black) Normally Open: (Blue) Wiring I nstructions: Pin 3: AC Line (White) Pin 3: AC Line (White) Pin 3) Grounded (not Pin 3: Normally Open connected or required) (White) Normally Closed: (Red) Pin 4) Sinking Output (Orange) Pin 5) DC Common (Black) Cable: 6' Cable: ' Cable: 6', Right Angle Parker Hannifin Corporation

22 How to Order Parker EPS proximity switches may be ordered on Series A, AN and MA cylinders as follows: ) Complete the basic cylinder model number. ) Place an S in the model number to denote switches and/or special features. End-of-Stroke Proximity Series A, AN, MA C05 3) Mounting styles E, D, DB, JB, or HB should be used with caution because of possible mounting interferences. Consult bulletin 0840-G-E for additional information. 4) Special modifications to cylinders other than switches must have a written description. Basic Cylinder Model Numbers 6 BB A U S 4 A Bore Size Double Rod Mounting Modifications Series Ports Special Modifications Rod End Thread Thread Type Stroke Cushion Head End Mounting Style Combination Mounting Style Piston Common Modifications Piston Rod Number Alternate Std. Rod End Thread Length Cushion Cap End Specify. Specify only if Cushion Head End is required. Use only if double rod cylinder is required. Specify mounting style. Specify any practical mounting style available. Specify P = Thrust Key Mounting M = Manifold Ports Specify A, AN, or MA. Standard Bumper * B = Standard Bumpers, Both Ends H = Standard Bumper, Head End C = Standard Bumper, Cap End Bumper Seal* 3 = Magnet only 4 = Bumper Seal only 6 = Bumper Seal & Magnet only Specify Port Type required: U = NPTF R = BSPP B = BSPT If required, specify: V = Fluorocarbon Seals F = Nut Retained Piston E = Buna Piston Seal; Fluorocarbon Rod Seal Specify rod code number. Specify only if times Standard Catalog A dim. is required. Specify Style: 4 = Small Male 8 = Intermediate Male 9 = Short Female 3 = Special 55 = Split Coupler Specify KK, A, LA or W dim. required. Specify only if special modifications (including proximity switches) are required. Do not use symbol S for rod end modifications. Specify A = UNF W = BSF M = Metric Specify only if Cushion Cap End is required. Specify in inches. *For MA Series only. Leave blank for Series A/AN. /4" stroke loss per end. Parker Hannifin Corporation

23 How to Specify EPS Switches How to Specify EPS Switches 5) Specify letter prefix H for EPS-7, D for EPS-6, and F for CLS-, or B for CLS-4, then fill in the four blanks specifying port location, switch orientation and actuation point for both head and cap. If only one switch is used, place XXXX in the unused blanks. End-of-Stroke Proximity Series A, AN, MA Example =H3CGG-XXXX denotes a switch on the head end only, EPS-7 Example =BXXXX-4BGG denotes a switch on the cap end only, CLS-4 C05 Head End R Specify: R = EPS-5 H = EPS-7 D = EPS-6 F = CLS- B = CLS-4 N = Prep for switches only Port Location See Figure. 3 Switch Location See Figure. A Switch Orientation See Figure for EPS-7 and Eps-6 only. GG Actuation Point GG = End of Stroke FF = Stroke to Go; See Bulletin 0840-G-E for stroke remaining. Cap End 4 Port Location See Figure. Switch Location See Figure. B Switch Orientation* See Figure for EPS-7 and Eps-6 only. GG Actuation Point GG = End of Stroke FF = Stroke to Go; See Bulletin 0840-G-E for stroke remaining. Note: All specified switch and port locations are as seen from rod end of cylinder. *EPS-5 switches will be oriented so that the connectors face each other. Figure Figure 4 3 A B C D E Example:.00 CJMAUS4AC5.00 S = H3C66-3CGG 3 Parker Hannifin Corporation

24 Cordsets Specifications EPS 5 & 7 Connectors The male quick disconnect on the Parker EPS-5 or 7 is a Brad Harrison connector. Female connects must be purchased with one of the following cable lengths. Parker Part No. Cable Length Automotive Standard 3' ' ' ' End-of-Stroke Proximity A, AN, MA Series EPS-5 or 7 Green AC White (3) L STANDARD. Green L. Black 3. White Black () Load AUTOMOTIVE Internally Short. Green Circuit Protected. Red 3. Red Pin Receptacle AC Color Code 3 C05 EPS 6 Connectors The male quick disconnect on the Parker EPS-6 is a Brad Harrison 430 connector. Plug Pin and Cable Identification ) +0 to 30 VDC (White) 3 ) Source (Red) 4 3) Grounded not connected nor required 5 4) Sink (Orange) 5) Common (Black) Cable Length Parker No WHITE (+) ORANGE 4 BLACK 5 (-) RED SINK (NPN) SOURCE (PNP) LED Function Ready Target Power Applied (No Target) ON OFF Target Present OFF ON Short Circuit Condition FLASH FLASH CLS Connectors The male quick disconnect on the Parker CLS- is a Brad Harrison connector. Female connects must be purchased with one of the following cable lengths. Parker Part No. Cable Length Standard 3' ' ' ' The connection for the CLS-4 are 44" PTFE insulated flying leads with /" conduit hub. 3-wire: Common (black), Normally open(blue), and Normally closed (red). CLS- Green AC White (3) L L Black () Load Internally Short Circuit Protected STANDARD. Green. Black 3. White Pin Receptacle AC Color Code 3 4 Parker Hannifin Corporation