Best choice of electric works

Transcription

1 Best choice of electric works Table of Contents Cable Hoists PC / WS 1 Grips S-X 2 Mesh Grips KG-XX 3 SK-XX 4 SG-XX 5 TG-XX 6 FRP Ladders FAD-CC 7 FP-XX 8 Cable Strippers JP TW-50A 10 CS-70/ Cable Straighter UCB Cable Puller CW-2500D 13 Cutters Manual cable cutter SH RCC RCC CC-400LT 17 Hydraulic cable cut head TC-085HE 18 TC-120HE 19 HYSC-20HE 20 HYSC-32HE 21 HYSC-55HE 22 HYCC-35HE 23 HYCC-105HE 24 HYCC-P85HE 25 HYCC-P100HE 26 P

2 Best choice of electric works Table of Contents Manual hydraulic cable cutters HYSC HYSC HYSC HYCC TC HYCC-P85 33 Bus bar tools Busbar cutter BC CT Bender BB HLB Pipe bender PB-10N 38 Punchers DRCP PNST PN SH-70A 42 SH XX-NSW 44 Compression Tools Dies(depend on request and drawing) SUS-xx 45 Manual crimping tools HD- XX 46 HD-BGD3/OD3 47 Hydraulic compression tools HYCP HYCP PH UCP CTE HYCP UB-412G 54 HYCP Hydraulic compression head HYCP-2612HE 56 HYCP-400HE 57 HYCP-4013HE 58 HYCP-15THE 59 HYCP-630HE 60

3 Best choice of electric works Table of Contents HYCP HE 61 HYCP-500HE 62 HYCP-60ST 63 SR-60SD 64 SR-100C2 65 SR-200M/MS 66 Dies (depend on request and drawing) CTE-60S (60ton s) 67 CTE-100A (100ton s) 68 Battery operated Tools REC REC REC-54AC 71 REC REC-85CCP 73 HEC-S26/45 74 HEC-C85 75 HEC-U27 76 HEC REC REC IS-MM20 80 IS-SC19L 81 Battery pack & charger (Suitable for IZUMI tools) BP-70Li 82 BP-70Hi 83 CH-70X 84 Electric Power Tools IS-CP13 85 JIT-120A 86 Hydraulic Nut Splitter HYNC-XX 87 Pump HP-700A 88 HYP-700FT 89 SGS-2 90 R14E-F1 91 P300S 92 D-x 93 SEP HPE-3ST 95 HPE-3DT 96

4 1 / 96 Cable Hoists PC/WS Cable Hoists Die no load Wire Wire Cable Weight Length length O/S dia. Max. Min. PC ton 1210mm 410mm 5mm 3.2kg PC ton 1400mm 480mm 6mm 4.2kg PC ton 1900mm 480mm 5mm 3.8kg - Applicable to the installation of electrical wire, auto transportation, and all upward pull or lift related work - Equipped with automatic brake and vertically parallel wheel stoppers. Die no load Wire Wire Cable O/S Weight Length length dia. Max. Min. WS ton 1900mm 480mm 38 x 2mm 4.5kg - Applicable to the installation of electrical wire, auto transportation, and all upward pull related work - Equipped with automatic brake and vertically parallel wheel stoppers. - Proof of voltage wear 15kV for 3 min F.R.P. Insulated handle Don't use for lifting Rotates 360 -

5 2 / 96 Grip S-X Grips Type no Load O/S. dia. Weight SD mm 0.71kg T mm 1.07kg - Used for copper cable, covered conductor, steel rod, messenger wire and copper cable Type no Load O/S. dia. Weight S2000C mm 1.37kg S2000CL mm 1.40kg - Copper cable, covered conductor, and messenger wire Type no Load O/S. dia. Weight 2000MCL mm 2.16kg - Copper cable, covered conductor, and messenger wire Type no Load O/S. dia. Weight S3000CL mm 2.46kg - Copper cable, covered conductor, and messenger wire

6 3 / 96 Mesh Grips KG-xx Mesh grips Type Cable Working E M(mm) Dia.(mm) load(kg) (mm) SHORT KG-050A KG-062A KG-075A KG-100M KG-125M KG-150M KG-200M KG-225M KG-300M Offer a rotating head with shoulders and double weave galvanized wire construction. The rotating head is manufactured from stainless steel and offers a more secure attachment to the pulling mechanism. The rotating head does not replace the use of a pullback swivel. There are no bearings to allow rotation under load and severe damage may occur to the utility being installed if this product is used without a proper swivel. KG-350M KG-400M KG-050M KG-062M KG-075M KG-100P KG-150P KG-200P KG-250P KG-300P KG-350P KG-400P KG-450L KG-500L KG-600L

7 4 / 96 Mesh Grips SK-xx Mesh grip Type Cable Working E M(mm) Dia.(mm) load(kg) (mm) SK-075A SK-100A SK-125A SK-150A SK-200A SK-250A SK-300A SK-350A SK-400A Used for outside plant cable, steel. - Easy to install and remove, reusable, - offer a flexible eye and double weave galvanized wire construction and are suitable for shorter pulls. - The lack of protective shoulders will cause the wire strands to wear more quickly

8 5 / 96 Mesh Grips SG-xx Mesh grip Type Cable Working E M(mm) Dia.(mm) load(kg) (mm) STANDARD SG-075A SG-100A SG-125A SG-150A SG-175A SG-200A SG-250A SG-300A Used for outside plant cable, steel. - Easy to install and remove, reusable, - Offer a flexible eye and double weave galvanized wire construction and are suitable for shorter pulls. - The lack of protective shoulders will cause the wire strands to wear more quickly SG-350A SHORT SG-075M SG-100M SG-125M SG-150M SG-200M SG-250M SG-300M SG-350M

9 6 / 96 Mesh Grips TG-xx Mesh grip Type Cable Working E M(mm) Dia.(mm) load(kg) (mm) SHORT TG TG TG TG TG TG TG TG TG Used for pulling irrigation pipe, insulated wire, wire rope, tubing, PVC, and bare conductors. - Reusable and easy to install and remove - Have a slim profile for small build-up. - Offer a flexible eye with shoulders and double weave galvanized wire construction. The shoulders offer added protection to the utility being pulled in as well as protecting the leading wire strands STANDARD TG TG TG TG TG TG TG

10 7 / 96 Ladder FRP FAD-CC FAD-CC SERIES Die No. Height Upper Width Lower Width Weight FAD-CC m 3.1 m 4.4 m 6.70 kg FAD-CC m 3.1 m 4.7 m 8.40 kg FAD-CC m 3.1 m 5.0 m 10.1 kg FAD-CC m 3.1 m 5.3 m 11.8 kg FAD-CC m 3.1 m 5.6 m 13.4 kg FAD-CC m 3.1 m 5.9 m 15.0 kg FAD-CC m 3.1 m 6.2 m 16.5 kg - Iron Lip on top cap - Width of straight ladder is 65mm - Anti-skipping rubber stopper - FRP material non-conductive - Anti-corrosive - Non-water absorption

11 8 / 96 Ladder FRP FP-xx FP Fiberglass Extension Ladders Die Extension Storage Working Weight No. Length Length Load FP m 3.24 m 110kg/ kg FP m 3.91 m 110/kg kg FP m 4.57 m 110/kg kg FP m 5.22 m 110kg/ kg - Rubber step safety belt with arc belt grip to prevent from breaking. - Arc shape handles to enable easy clutching and holding. - Rubber covered hook to use when using the extension ladder without leaning against a wall. - Anti-skid stopper to prevent bursting when upper ladder declines.

12 9 / 96 Cable Stripper JP-130 Cable Stripper, for insulation layer - Stripper capacity: For 110KV 220KV cable of O.D mm For stripping insulation <25mm in thickness 430 X 120 X 240 mm 3.6 kg - 8 bearing rollers enable insulation stripping in balance motion. - Slope of bearing rollers defines the thickness of insulation to be stripped. Users should adjust the slope to strip at appropriate thickness. - Stripper body made of stainless steel 6mm in thickness

13 10 / 96 Cable Stripper TW-50A Adjustable MV underground cable stripper - Apply for 1/0 AWG to 1000 MCM URD cable, 0.50 to 2.25 in(12.70 to 57.15mm) - Cut off the outer shell, end insulator, outside semiconductor 14.5 in (368 mm) 2.1 lb (.953 kg) - Replacement blades CB 50A - standard reach blade CB 50 - Long reach blade - Two handles permit safe, easy operation on XLPE, plastic, polyethylene and EPR insulation of all thicknesses - Adjustable strip stop bar gives an exact stripping conductor length and can be rotated to allow unlimited stripping - Safe, clean cuts prevent conductor damage - Adjustable to fit wide range of cable O.D. S - Bushings are optional accessories, and can be tailored.

14 11 / 96 Cable Stripper CS-70/150 HV underground cable stripper - Apply for KV cable: Dia mm - Strip the main insulating layer of XLPE cable - Chop the outside semi-conducting layer of XLPE cable - Tool kit 1 set - Hexagon Wrench 1 pc - CSB-40 & CSB-10 spare blade 1pc of each - Five track rollers make the cutting blade move freely - Cutting blade can be fine-tuning and fixed - Al. Alloy mainstay is rust proof - Single handle to adjust the cable dia., simplify the operation - Fixtures to avoid of the setting measure movement

15 12 / 96 Cable Straightener UCB-160 HV cable Straightener - Apply for KV, Dia.160mm underground cable for straightening - Output force: 5 ton - Cylinder lift: 231.9mm - Working pressure: 700bar mm 35.5kg - 3 cylinder fixed holes to adjust the straightening angle - High quality surface treating techniques lead to high abrasion performance - Configured TC-371 hydraulic quick coupling to connect with both electrical pump and hand pump( optional )

16 13 / 96 Cable Puller CW-2500D Cable Puller Compact, Very Quiet, Powerful Motor including Load Display and Footswitch - Pulling Force: 14.7kN in high speed 24.5kN in low speed - Pulling Speed: 6.4~3.5m/min in high speed 3.7~2.0m/min in low speed - Motor: AC V/ V 750W 640x450x300cm (LxWxH) 59.0 kg - With Digital Load Display and Foot Switch - Display pulling distance, current and pulling force. - External Data Recorder available as option to connect to personal computer and printers. - Can be use on power cable and OPGW and CATV cable, indoor power distribution cables etc.

17 14 / 96 Cutter Manual Cable Cutter SH-320 Manual cable cutter (ratchet), made in German - Cutting capacity: 300mm 2 copper an Al. cable 252mm(L) 610kg ACCESSERIES - Cutting blade wide enough to keep the shape - Ratchet gear small save labor - Durability forging blade - Skid-proof grip - Easy for one hand operation

18 15 / 96 Cutter Manual Cable Cutter RCC-325 Manual cable cutter - Cutting capacity: Cuts up to 400mcm (200sq.mm) hard drawn copper Cuts up to 600mcm (325sq.mm) soft copper, Al. And multiple conductor cable 250mm 0.65kg - Cutting blade wide enough to keep the shape - Single speed ratchet mechanism - Quick release mechanism for removal of cable to completion of cut - Tool can be locked in closed position - Convenient for working in tight places and easy to store

19 16 / 96 Cutter Manual Cable Cutter RCC-500 Manual cable cutter - Cutting capacity: Cuts up to 600mcm (500sq.mm) soft copper, Al. and multiple conductor cable 285mm (L) 0.85kgs ACCESSERIES - Simple, one-hand operation - Single speed ratchet mechanism - Quick release mechanism for removal of cable to completion of cut - Tool can be locked in closed position - Convenient for working in tight places and easy to store

20 17 / 96 Cutter Manual Cable Cutter CC-400LT Manual cable cutter - Cutting Capacity: Cooper Al. Cable SQ MM, AWG 800 MCM 700mm (L) 1.57kg ACCESSERIES Kraft box - Apply for the 400 mm² BLW Copper Aluminum Cable - Al. Alloy handle - Changeable head - Compound handle design Easy cutting Alu. Tube handles

21 18 / 96 Cutter Hydraulic cable cut head TC-085HE Split hydraulic cable cutter - Cutting capacity: a. <600V low tension cable 1000mm 2 lower b. x-linked poly ethylene(xlpe) cable : dia. 85mm, 300mm 2 x 3 c. Copper, Al., CCP cable: 85mm - Oil volume required: 73cc - Output force: 6.5 ton 465 x 155 x 65mm ***************************** 5.1kg ACCESSERIES - Carrying bag - Safe protecting cover(optional) TC-085HEC - Flip-top quicken install head - SGS certification - External pump for rapid cutting - Can be connected with all 700bar (10,000psi) pump - Spring return single-acting cylinder - Blade change easily

22 19 / 96 Cutter Hydraulic cable cut head TC-120HE Split hydraulic cable cutter - Cutting capacity: a. <600V low tension cable 1500mm 2 lower b. x-linked poly ethylene(xlpe) cable : dia. 120mm, 1600mm 2 lower c. Copper, Al., CCP cable: 120mm - Output force: 15ton - Max. Pressure: 700bar - Oil volume required: 140cc 556 x 185mm *************************** 10.3kg ACCESSERIES - Carrying bag - Safe protecting cover(optional) TC-120HEC - Lock pin quicken install head - Single-acting hydraulic jack - SGS certification - External pump for rapid cutting - Can be connected with all 700bar (10,000psi) pump - Spring return single-acting cylinder - Blade change easily

23 20 / 96 Cutter Hydraulic cable cut head HYSC-20HE Split hydraulic cable cutter ***************************** - Cutting capacity: a. Wire rope 6x716 mm b. Wire rope 6x1216 mm c. Wire rope 6x1916 mm d. Soft steel bar16 mm e. Reinforcing rod13 mm f. Cu Strands20 mm g. Al Strands20 mm h. ACSR21 mm i. Guy wire 1x715 mm j. Guy wire 1x1916 mm k. CCP cable N/A l. Cutting of piano wire is prohibited. Oil volume required: 73cc - Oil volume required: 49cc - Output force: 5.3 ton 240 (L)mm 2.4kg ACCESSERIES - Carrying bag - Flip-top quicken install head - SGS certification - External pump for rapid cutting - Can be connected with all 700bar (10,000psi) pump - Spring return single-acting cylinder - Blade change easily

24 21 / 96 Cutter Hydraulic cable cut head HYSC-32HE Split hydraulic cable cutter ***************************** - Cutting capacity: a. Wire rope 6x732 mm b. Wire rope 6x1232 mm c. Wire rope 6x1932 mm d. Soft steel bar25 mm e. Reinforcing rod25 mm f. Cu Strands32 mm g. Al Strands32 mm h. ACSR32 mm i. Guy wire 1x732 mm j. Guy wire 1x1932 mm k. CCP cable N/A l. Cutting of piano wire is prohibited. Oil volume required: 135cc - Output force: 25.4 ton 300 (L)mm 10.0kg ACCESSERIES - Carrying bag - Flip-top quicken install head - SGS certification - External pump for rapid cutting - Can be connected with all 700bar (10,000psi) pump - Spring return single-acting cylinder - Blade change easily

25 22 / 96 Cutter Hydraulic cable cut head HYSC-55HE Split hydraulic cable cutter **************************** - Cutting capacity: a. Steel wire 6x7: 25mm b. Steel wire 6x12: 30mm c. Steel wire 6x19: 30mm d. Soft steel rod: 22mm e. Reinforcing Rod: 19mm f. CSC: 50mm g. ASC: 50mm h. ACSR: 50mm i. Tension Line 1x7: 15mm j. Tension Line 1x19: 20mm - Output force: 14.9 ton - Max. Pressure: 700bar - Oil volume required: 106cc 415mm (L) 9.0kg ACCESSERIES Carrying bag - Equipped with PT3/8 Threaded Izumi high pressure couples - Lock pin cutting head - External pump for rapid cutting - Can be connected with all 700bar (10,000psi) pump - Spring return single-acting cylinder - Blade change easily

26 23 / 96 Cutter Hydraulic cable cut head HYCC-35HE Split hydraulic cable cutter - Cutting capacity: a. <600V low tension cable 400mm 2 lower b. x-linked poly ethylene(xlpe) cable : dia. 30mm lower c. Copper, Al. cable: 35mm - Output force: 13 ton - Max. Pressure: 700bar - Oil volume required: 63cc 420 x 125 x 255mm ****************************** 9.7kg ACCESSERIES - Carrying bag FEATURES - Apply for copper stranded wire and rubber cable - C-framed 38mm open head design easy to put the material in - External pump for rapid cutting - Can be connected with all 700bar (10,000psi) pump - Spring return single-acting cylinder - Blade change easily

27 24 / 96 Cutter Hydraulic cable cut head HYCC-105HE Split hydraulic cable cutter - Cutting capacity: a. Telecom cable: Dia.100mm lower b. <600V low tension cable: 1000mm 2 lower c. x-linked poly ethylene(xlpe) cable : Dia. 100mm lower, 300 mm 2 x 3 d. CSC cable: 42mm e. ASC cable: 46mm f. CCP cable: 105mm - Output force: 10 ton - Max. Pressure: 700bar - Oil volume required: 178cc ******************************** 590 x 760 x 274mm 13kg ACCESSERIES Plastic carry case FEATURES - Apply for the low tension cable and telecom cable - Handle design for easy operation - Lock pin cutting head - External pump for rapid cutting - Can be connected with all 700bar (10,000psi) pump - Spring return single-acting cylinder - Blade change easily

28 25 / 96 Cutter Hydraulic cable cut head HYCC-P85HE Split hydraulic cable cutter **************************** - Cutting capacity: a. Cu Strands28 mm b. Al Strands38 mm c. Wire rope 6x785 mm d. Wire rope 6x12N/A e. Wire rope 6x19N/A f. Soft steel bar N/A g. Reinforcing rod N/A h. ACSRN/A i. Guy wire 1x7N/A j. Guy wire 1x19N/A k. CCP cable N/A l. Cutting of piano wire is prohibited. - Max. Pressure: 700bar - Oil volume required: 65cc - Output force: 4.9ton - Ram Stroke: 91.5 mm 460mm (L) 7.2kg ACCESSERIES Carrying bag FEATURES - Equipped with PT3/8 Threaded Izumi high pressure couples - Lock pin cutting head - External pump for rapid cutting - Can be connected with all 700bar (10,000psi) pump - Spring return single-acting cylinder - Blade change easily

29 26 / 96 Cutter Hydraulic cable cut head HYCC-P100HE Split hydraulic cable cutter **************************** - Cutting capacity: a. Cu Strands28 mm b. Al Strands38 mm c. Wire rope 6x785 mm d. Wire rope 6x12N/A e. Wire rope 6x19N/A f. Soft steel bar N/A g. Reinforcing rod N/A h. ACSRN/A i. Guy wire 1x7N/A j. Guy wire 1x19N/A k. CCP cable N/A l. Cutting of piano wire is prohibited. - Max. Pressure: 700bar - Oil volume required: 140cc - Output force: 8.8ton - Ram Stroke: 110 mm 590mm (L) 13.2kg Accessories Carrying bag FEATURES - Equipped with PT3/8 Threaded Izumi high pressure couples - Lock pin cutting head - External pump for rapid cutting - Can be connected with all 700bar (10,000psi) pump - Spring return single-acting cylinder - Blade change easily

30 27 / 96 Cutter Hydraulic cable cut head P-170 Split hydraulic cable cutter - Output force:30ton - Working pressure: 700bar - cutting ability: i. <600V low tension cable: 2600mm 2 lower ii. x-linked poly ethylene(xlpe) cable : dia. 160mm, 2600mm 2 lower mm 50kg **************************** ACCESSERIES Carrying bag FEATURES - Operated by heavy load double-action hydraulic jack - Lock pin cutting head - External pump for rapid cutting - Can be connected with all 700bar (10,000psi) pump - Blade change easily - Big cutting capacity of dia.160mm

31 28 / 96 Manual hydraulic cable cutters Manual / Integrative HYSC-24 Integrative hydraulic cable cutter - Cutting capacity: Steel cable: 6 X 19=> Dia.24mm lower Iron: Dia.20mm lower ACSR(aluminum conductor steel reinforced) cable: Dia.24mm lower - Power: 78KN - Max Pressure: 700bar - Reservoir capacity: 56cc - Max Output: 6.7ton ***************************** 426 x 52 x 140mm 4.0kg ACCESSERIES Carrying bag FEATURES - Single Passages oil supply design - Guillotine type cutting for less jamming than shear type cutting - Flip-top Latch cut head easy to open and close, and easy to take in the cutting material - No set-up time required - Ergonomic design of pressing handle - Cut head 180 rotation, 360 work direction, especially for aloft work

32 29 / 96 Manual hydraulic cable cutter Manual / Integrative HYSC-32 Integrative hydraulic cable cutter ***************************** - Cutting capacity: a. Wire rope 6x716 mm b. Wire rope 6x1216 mm c. Wire rope 6x1916 mm d. Soft steel bar16 mm e. Reinforcing rod13 mm f. Cu Strands20 mm g. Al Strands20 mm h. ACSR21 mm i. Guy wire 1x715 mm j. Guy wire 1x1916 mm k. CCP cable N/A l. Cutting of piano wire is prohibited. Oil volume required: 73cc - Max Pressure: 700bar - Reservoir capacity: 165cc - Max Output: 25.4ton 580mm 9.3kg ACCESSERIES Carrying bag FEATURES - Single Passages oil supply design - Guillotine type cutting for less jamming than shear type cutting - Flip-top Latch cut head easy to open and close, and easy to take in the cutting material - No set-up time required - Ergonomic design of pressing handle - Cut head 180 rotation, 180 work direction, especially for aloft work

33 30 / 96 Manual hydraulic cable cutter Manual / Integrative HYSC-45 Integrative hydraulic cable cutter - Cutting capacity: a. Wire rope 6x7 22 mm b. Wire rope 6x12 25 mm c. Wire rope 6x19 25 mm d. Soft steel bar 20 mm e. Reinforcing rod 16 mm f. LGJ ACSR: 45MM g. GJ steel strands: 20mm h. LJ &TJ Cu. Al. Strands: 45mm - Max Pressure: 700bar - Max Output: 10ton ***************************** 640mm 6.8kg ACCESSERIES - Carrying bag - Shoulder strap FEATURES - Single Passages oil supply design - Two stage pimping action for rapid ram advance - Lock-in cut head easy to open and close, and easy to take in the cutting material - Ergonomic design of pressing handle - Cut head 180 rotation, 180 work direction, especially for aloft work - Blade can be changed easily

34 31 / 96 Manual hydraulic cable cutter Manual / Integrative HYCC-050 Integrative hydraulic cable cutter - Cutting capacity: a. <600V low tension cable: dia.50mm, 500mm 2 lower b. x-linked poly ethylene(xlpe) cable: 500mm, 500mm 2 lower c. copper cable, copper wire, Al. Cable, CCP cable: 50mm - Output force: 4 ton - Reservoir capacity: 89cc - Working pressure: 700bar ******************************* 480 x 55 x 140mm 3.8kg ACCESSERIES Carrying bag FEATURES - Apply for telecom and electric power underground ACSR cable - Guillotine type cutting for less jamming than shear type cutting - Cut head 180 rotation - Spring return piston - No set-up time required - Light weight - Up and down blade change easily - Flip-top latch cut head for easy insertion of cutting material

35 32 / 96 Manual hydraulic cable cutter Manual / Integrative HYCC-P85 Integrative hydraulic cable cutter - Cutting capacity: Cu strands: 28 mm Al strands: 38 mm CCP cable: 85 mm - Max Pressure: 700bar - Max Output: 4.9ton - Reservoir capacity: 145cc 715mm ***************************** 10.0kg ACCESSERIES - Carrying bag FEATURES - Apply for telecom and electric power underground ACSR cable - Guillotine type cutting for less jamming than shear type cutting - Cut head 180 rotation - Spring return piston - No set-up time required - Light weight - Up and down blade change easily - Flip-top latch cut head for easy insertion of cutting material

36 33 / 96 Manual hydraulic cable cutter Manual / Integrative TC-085 Integrative hydraulic cable cutter - Max cutting capacity: Cu cable, Al cable, CCP Cable:85mm - Max Pressure: 700bar - Reservoir capacity: 168cc - Output force: 5.6ton 667mm (L) 9.0kg ***************************** ACCESSERIES Carrying bag FEATURES - High-low multiple oil supply make quicken the cut speed - Guillotine type cutting for less jamming than shear type cutting - Cut head 180 rotation - Spring return piston - No set-up time required - Light weight - Up and down blade change easily - Flip-top latch cut head for easy insertion of cutting material

37 34 / 96 Busbar Fabrication Tools Busbar Cutter BC-160 Busbar Cutter - Cutting capacity: Copper Aluminum bar mm - Output force: 25ton - Working pressure: 700bar 265 x 298 x 456mm 28 kg FEATURES - Fixing Vice ensure effective cutting - V-shape cutter perform excellent cutting quality - Locating clamp can insure the cutting angle of 90, can be used together with the punching guide plate - Front an back material feeding tumbling box

38 35 / 96 Angle steel Tools Angle steel cutter CT-100 Angle steel Cutter - Output Force : 450kN - Capacity: Angle Steel L110 x 110x 10 mm Steel Plate 110 x 10 mm 42kg - Quick cutting, no scrap iron, smooth surface of cutting flat. - Suit for using in bridge high pressure of iron tower and place. - Outside using, convenient carry and simple operation.

39 36 / 96 Busbar Fabrication Tools Busbar bender BB-200 Busbar bender - Operating Press: 700bar - Min bending size 45mm,U-style bending inside 70mm,Z-type bending fall 70mm - Max bending angle Cutting Capacity: copper al. Bar 200 x 200mm 600 x 250 x 280mm 30KG FEATURES - Bending degree display - Bending axle R10, R15,R30mm changeable - Bayonet Joint bending axle handle material easily - Central line located design fixtures

40 37 / 96 Busbar Fabrication Tools H-shape Bender EB-125 Busbar H-shape Bender - Output Force : 270 KN - Stroke: 168mm - Capacity: Busbar 125x12mm 55 kg - Guiding Plate - Bending Scale - V-shape cutter ensure effective cutting - Operated by spring Return single acting pump - Apply for both strange bending and side bending of changing dies

41 38 / 96 Pipe Bender PB-10N Pipe Bender - Bending capacity: Thin Steel Conduit Thick: 15mm-75mm (5/8"-3") Steel Conduit: 16mm-82mm (1/2"-3") Gas Pipe: 15mm-65mm (1/2"-2 1/2") - Operating Press: 700bar - Oil volume required: 398cc - Output force: 11.1ton - Max bending degree: mm (W) 18.6 kg - Plastic carry case - Frame - Cylinder - Pivot shoes 2pcs - Designed to bend various sizes and thickness of steel pipes without wrinkles - An aluminum alloy frame makes this bender lighter to carry - Can be operated by any double acting hydraulic pump (with the max, oil pressure of 700 bar or 10,000 psi)

42 39 / 96 Puncher Din rail punch DRCP Angle Steel puncher - 8.8mm x 5mm hole along or perpendicular to the axis of the rails 111mm 12.0 kg ************************ - Location Ruler - Standard dies - Cutting tool for 5 DIN sections cuts without burrs or deformation - This cutter is supplied complete with a Ruler and a Stopper

43 40 / 96 Puncher Sheet Metal Punch PNST-10 Sheet metal puncher - Capacity: φ20.5 mm x 10mm - Operating Pressure: 68.8 Mpa or 10,000 psi - Output Force : 10ton - Ram Stroke: 25mm - Max. Pressure: 700 bar - Oil Required: 47 cc 125mm 1.9kg ************************** - PDV-10 (Punch driver) - HP-180N (Hydraulic hand pump) - 6 sets Punch & dies (1/2", 3/4", 1", 1-1/4", 1-1/2", 2") 3 pcs Draw stud adaptors (S, M, L) 2 pcs Draw studs (3/8", 3/4") - Hydraulic punching tools are made from high quality materials - Characterized by perfect and problem-free punching of metal - sheet to thickness of 3.2 mm(mild steel) and 1.6 mm(stainless steel) - HP-180N is designed for PDV-10 (Punch driver) or any other tool heads that require less than 180 cc of oil volume. HP-180N is not - equipped with a relief valve. - Do not use HP-180N with any compression head that requires a relief valve.

44 41 / 96 Puncher Sheet Metal Punch PN-052 Sheet metal puncher - Sheet metal thickness: Stainless steel: 1.6 mm Mild steel: 3.2 mm - Max. hole diameter: 4 inch, 4 inch diameter hole on 3.2 mm thickness mild steel - Output Force : 12.7ton - Ram Stroke: 25mm - Oil Required: 46.7 cc ************************** 125mm 7.6kg - PDV-10 (Punch driver) - 6 sets Punch & dies (1/2", 3/4", 1", 1-1/4", 1-1/2", 2") 3 pcs Draw stud adaptors (S, M, L) 2 pcs Draw studs (3/8", 3/4") - Hydraulic punching tools are made from high quality materials - Characterized by perfect and problem-free punching of metal - sheet to thickness of 3.2 mm(mild steel) and 1.6 mm(stainless steel) - HP-180N is designed for PDV-10 (Punch driver) or any other tool heads that require less than 180 cc of oil volume. HP-180N is not - Equipped with a relief valve. Do not use HP-180N with any compression head that requires a relief valve.

45 42 / 96 Puncher Angle steel punch SH-70A Angle Steel puncher - Operating Pressure: 68.8 Mpa or 10,000 psi - Output Force : 310 KN - Throat Depth: 70 mm - Capacity: φ20.5 mm x 10mm 360 X 210 mm 13.0 kg , 13.5, 17.5, 20.5 mm punch & die sets. - PPE Carrying Case - Hex Wrench, Die sets Fix Wrench - Options: Punching die sets Copper & Al.: Cu6,7,8,9,10,10.5,11,12,13.5,17.5,20.5 Mild Steel:S6~S9 - Apply for angle iron, plates, beams and bus bar - C-framed hefty forged steel punching head - Handle design for easy movement - Firm base for accurate location and punch - Apply for all 700bar output force pump - 70mm throat depth allows commonly used angle iron - New fixed support stand - Stripper guide clamps punch in place to free operator s hand

46 43 / 96 Puncher 16Mn angel steel punch SH-80 16Mn Steel puncher - Operating Pressure: 68.8 Mpa or 10,000 psi - Output Force : 31 Ton - Throat Depth: 70 mm - Capacity: φ20.5 mm x 10mm - Oil Required: 82 cc 357 x 244 mm 18.5 kg , 13.5, 17.5, 20.5 mm punch & die sets. - PPE Carrying Case - Hex Wrench, Die sets Fix Wrench - Options: Punching die sets Copper & Al.: Cu6,7,8,9,10,10.5,11,12,13.5,17.5,20.5 Mild Steel:S6~S9 - Apply for angle iron, plates, beams and bus bar - C-framed hefty forged steel punching head - Handle design for easy movement - Firm base for accurate location and punch - Apply for all 700bar output force pump - 70mm throat depth allows commonly used angle iron - New fixed support stand - Stripper guide clamps punch in place to free operator s hand

47 44 / 96 Puncher Steel bar/busbar punch XX-NSW Long hole / square hole 506nsw 706NSW 606nsw 711NSW - All units, from the small, light models to powerful types, are chosen by our customers because of their excellent ease of operation. - Standard models are used to punch elongated holes. Bits with elongated holes are also standardized, and we have a large inventory. * - In combination with the powerful Royal double-acting hydraulic pump, these punchers will punch holes quickly, accurately, safely, and quietly. ** - The new 506NSW, a puncher for small shape steel, has a 5 taper die for channel steel that is a standard item in stock. 911NSW 1101SW Elongated holes are an option for the 1150SW only. ** Noise is generated when steel material is very hard. Max Punching Speed 1150SW ************************ ecs 506NSW 606NSW 706NSW 711NSW 911NSW 1101SW 1150SW Max.Capacity 270kN 350kN 450kN 500kN 600kN 650kN 1000kN Max.Ability φ18 12 φ22 13 φ24 16 φ24 16 φ24 20 φ25 21 φ30 25 Reach 55mm 60mm 60mm 110mm 102mm 102mm 150mm Weight 13kg 18kg 21kg 28kg 34kg 40kg 120kg Applicable 70Mpa(720kgf/cm2) Double-acting type (Classification according to the pump/puncher combination) Puncher 911NSW 1101SW 1150SW Time (Sec) Punch Return Punch Return Punch Return D-3SW Hyd. D-2SW pump D-1SW SW Accessories φ11, φ11, φ14, φ17.5, φ17.5, φ17.5, φ22, When purchase as a set with a hydraulic pump,two 5-m hoses are including. Customers can change the accessories to desired sizes. In making holes with these punchers, hole diameter must be larger than material thickness (SS400). Puncher 506NSW 606NSW 706NSW 711NSW Time (Sec)Punch Return Punch Return Punch Return Punch Return D-3SW Hyd. D-2SW pump D-1SW SW

48 45 / 96 Puncher Stainless steel Punch die SUS-xx Punch die for stainless steel plate - Punching capacity: Apply for the 3.5mm, dia.61.5mm below stainless steel plate Type No Conduit Hole Plate size size thickness (mm) (mm) SUS-22 1/ SUS-28 3/ SUS SUS / SUS / SUS ************************** - Tool box - Small screw 1pc(optional) - Big screw 1pc(optional) - 3pcs punching pieces easily to take out and save power - Auto central focus

49 46 / 96 Compression Tools Manual crimping tools HD- XX Manual / Hand operating Type Crimping Size Weight capacity HD mm 2 390mm 1.1kg HD mm 2 650mm 2.9KG HD mm 2 650mm 2.9KG Standard dies: Type Die mm 2 HD , 10, 16, 25, 35, 50 HD-0650 HD , 16, 25, 35, 50, 70, 95, 120 HD , 35, 50, 70, 95, 120, 150 FEATURES HD-06120, HD High-precision Stamping Crimping head not deformation - Rotate style Crimping die no need disassemble and change - Easy to operate and crimping fast - Apply for general ground operation

50 47 / 96 Compression Tools Manual crimping tools HD-BGD3/OD3 Manual / Hand operating, W-dies - Output force: 4.5ton - W-style dies - Size: 645L mm - Weight: 3.2kg HD-BGD3 / HD-0D3 FEATURES - Dies are sold separately, Bundy W-dies changeable. - Proper crimping are assured with butting steel jaws - Increased strength and greater bearing area is provided with larger steel bolts. - Fast, easy, one-hand die insertion - No lost dies with spring loaded positive lock die retainer buttons - Full crimping force assured with cover center cam action - Easy tool adjustment with butt stops and heat shrink tubing. - Long life expectancy provided with select clear hickory handles and light weight high strength alu. Alloy castings. - Easier tool operation is provided with bent handles and anti-slip grips - The 3D groove accommodates the line of type W die inserts

51 48 / 96 Compression Tools Hydraulic Compression head / Split style HYCP-2612HE Single acting - Ram stroke: 26mm - Working pressure: 700bar - Output force: 120KN - Crimping Capacity: mm 2 - Oil volume required: 47cc 195 x 70 x 125mm 3.6kg - Standard Die: CU16/25/35/50/70/95/120/150/185/240/300/400 - Plastic carry case *********************** FEATURES - Accept for the Alcoa, Bundy, T&B, Klauke, Cembre and Blackburn 12ton crimping compressors - Dies are sold separately - C-framed 26mm open crimping head, apply for the end and middle crimping - Operated by any 700bar (1000psi) hydraulic pump - Single acting spring return cylinder

52 49 / 96 Compression Tools Hydraulic Compression head / Split style HYCP-400HE Single acting - Ram stroke: 32mm - Working pressure: 700bar - Output force: 12TON - Crimping Capacity: mm 2 - Oil volume required: 53cc 276mm 5.0kg ACCESSERIES - Standard Die: CU16/25/35/50/70/95/120/150/185/240/300/400 - Plastic carry case *********************** FEATURES - Accept for the Alcoa, Bundy, T&B, Klauke, Cembre and Blackburn 12ton crimping compressors - Die sold separately - C-framed 32mm open crimping head, apply for the end and middle crimping - Operated by any 700bar (1000psi) hydraulic pump - Single acting spring return cylinder

53 50 / 96 Compression Tools Hydraulic Compression head / Split style HYCP-4013HE Single acting - Ram stroke: 38mm - Working pressure: 700bar - Output force: 120KN - Crimping Capacity: mm 2 - Oil volume required: 47cc 230 x 70 x 125mm 4.8kg ACCESSERIES - Standard Die: CU16/25/35/50/70/95/120/150/185/240/300/400 - Plastic carry case *********************** FEATURES - Accept for the Alcoa, Bundy, T&B, Klauke, Cembre and Blackburn 12ton crimping compressors - Die sold separately - C-framed 38mm open crimping head, apply for the end and middle crimping - Operated by any 700bar (1000psi) hydraulic pump - Single acting spring return cylinder

54 51 / 96 Compression Tools Hydraulic Compression head / Split style HYCP-15THE Single acting - Ram stroke: 50mm - Working pressure: 700bar - Output force: 150KN - Crimping Capacity: Copper: mm 2 Al.: mm 2 clamper tube: LGJ240 BLW - Oil volume required: 107cc 375 x 90 x 65mm 6.8kg ************************* ACCESSERIES - Standard Die: CU16/25/35/50/70/95/120/150/185/240/300/400 - Plastic carry case - Accept for the Alcoa, Bundy, T&B, Klauke, Cembre and Blackburn 12ton crimping compressors - Dies are sold separately - C-framed 50mm open crimping head, apply for the end and middle crimping - Operated by any 700bar (1000psi) hydraulic pump - Can change the dies to make the power distribution and underground cable crimping - Accepts Bundy P type dies - Single acting spring return cylinder

55 52 / 96 Compression Tools Hydraulic Compression head / Split style HYCP-630HE Single acting - Output force: 250kN - Ram Stroke: 28mm - Capacity: L16-630mm² - T mm² - Rate Pressure: 68.8Mpa or 10,000 Psi - Oil volume required: 110cc 250x88x120mm 5.6 kg - Standard Die: CU 400/ 500/ Plastic carry case ************************* FEATURES - Accept for the Alcoa, Bundy, T&B, Klauke, Cembre and Blackburn 12ton crimping compressors - Dies are sold separately. - With Parker coupler - Operated by any 700bar (1000psi) hydraulic pump - Single acting spring return cylinder - Location pin for firm location work - Hexagon, dot, circle crimping - U-framed compression head

56 53 / 96 Compression Tools Hydraulic Compression head / Split style HYCP HE Single acting - Ram stroke: 35mm - Working pressure: 700bar - Output force: 450KN - Crimping Capacity: mm 2 - Oil volume required: 233 cc 285 x 115 x 120mm 11.0kg Plastic carry case ************************ FEATURES - Dies are sold separately. - With Parker coupler - Location pin for firm location work - Hexagon, dot, circle crimping - U-framed compression head - Operated by any 700bar (1000psi) hydraulic pump - Single acting spring return cylinder

57 54 / 96 Compression Tools Hydraulic Compression head / Split style HYCP-500HE Single acting - Ram stroke: 26mm - Working pressure: 700bar - Output force: 300KN - Crimping Capacity: Copper: mm 2 Al.: mm 2 clamper tube: LGJ240 BLW JIS AWG DIN Copper Al ASRC Oil Volume required: 135cc 380 x 125mm 16kg ************************* Steel carry case FEATURES - Apply for the grips, terminal and clamper tube compression - Simple and compact design - Yoke type head - Positive die locking mechanism - Operated by any 700bar (1000psi) hydraulic pump - Single acting spring return cylinder

58 55 / 96 Compression Tools Hydraulic Compression head / Split style HYCP-60ST Single acting - Output force: 540kN - Ram Stroke: 38.5mm - Compression Range: up to 60mm O.D Sleeve - Rate Pressure: 68.8Mpa or 10,000 Psi - Oil volume required: 303cc 140(Dia)x440(H) mm with Ground stand 22.0 kg - Steel carry case - Ground stand - Die adapter for 12ton U-type dies(option) ************************ FEATURES - Dies are sold separately. - Accepts all dies used for Alcoa, Kudos, IZUMI 60 ton compressors. - With Parker coupler - Portable and light weight - Large handle for easy carrying - Specify the manufacturer s die and connector numbers - Single acting hydraulic pump required. - Operated by any 700bar (1000psi) hydraulic pump

59 56 / 96 Compression Tools Hydraulic Compression head / Split style SR-60SD Single / Double acting - Output force: 62.8ton - Ram Stroke: 39mm - Compression Range: up to 60mm O.D Sleeve 170(Dia)x380x140(H) mm 28.5 kg - Steel carry case - Ground stand - Die adapter for 12ton U-type dies(option) ***************************** FEATURES - Apply for all Alcoa, 60ton compression die, connected to all double acting 700bar hydraulic pump - Die sold separately - With Parker coupler - No connector jamming - Used for aloft work - Move freely in power transmission and distribution system compression - Operated by Single / double acting hydraulic pump

60 57 / 96 Compression Tools Hydraulic Compression head / Split style SR-100C2 Double acting - Output force: 1000kN - Ram Stroke: 24mm - Compression Range: up to 76mm O.D Sleeve 200(Dia)x350(H) 32.0 kg - Steel carry case - Standard dies: Die no A B C 100-G G G G ********************************* 100-G G G G G FEATURES - Dies are sold separately. - Accepts all dies used for Alcoa, KUDOS, IZUMI 100 ton compressors. - With Parker coupler - Rapid operation rotation die cover - Operated by double acting hydraulic pump

61 58 / 96 Compression Tools Hydraulic Compression head / Split style SR-200M/MS Double acting - Output force: 200ton - Operating Pressure: 68.6MPa - Operation: Double Acting - Ram Stroke: 35mm - Max. Compression Capacity: φ90.0mm ACCESSERIES - Steel carry case - Standard dies: For steel sleeve Die no A (mm) B (mm) C (mm) 200-G G G G G G For Al. sleeve Die no A (mm) B (mm) C (mm) 200-L ************************** Type no Brand Stroke Force Size Weight Remark SR200M SANWA 35mm 200ton 365x280x370mm 85kg Standard SR200MS SANWA 35mm 200ton 365x262x370mm 75kg Light - Dies are sold separately. - Accepts all dies used for Alcoa, Bundy, or IZUMI 200 ton compressors. - With Parker coupler - Simple design for the easy maintenance - Removable die cap design helps operator an easy insertion and removable of the connector - Operated by double acting hydraulic pump 200-L L L L L L L L L L For copper sleeve Die no A (mm) B (mm) C (mm) 200-T T T T T T Notes: A dia. B 1/2 crimping size c crimping Width

62 59 / 96 Compression Tools Hydraulic Compression tools / Manual HYCP-180 Manual / Hand operating - Crimping capacity: Cu mm 2 - Reservoir capacity: 56cc - Output force: 5.2ton - Rate Pressure: 550bar 370mm 2.5kg - Plastic carry case - Standard Dies: 10/16,25/35,50/70,95/120,150/185 ********************** - Dies are sold separately - Also apply for the BEKU die - Light weight, compact and slim design - Yoke and Latch type head for easy die changeover and easy removal of jointed conductor - Adjustable ram stroke, 10-15mm to minimize pumping action - Built-in bypass relief valve - Small handle spread

63 60 / 96 Compression Tools Hydraulic Compression tools / Manual HYCP-240 Manual / Hand operating - Output force: 52KN - Crimping capacity: Cu mm 2 - Reservoir capacity: 56cc - Max. Pressure: 550 bar 120 x 375mm 2.3kg - Plastic carry case - Standard Dies: 10/16,25/35,50/70,95/120,150/185,240 ********************** - Dies are sold separately - Also apply for the BEKU die - Light weight, compact and slim design - Yoke and Latch type head for easy die changeover and easy removal of jointed conductor - Adjustable ram stroke, 10-15mm to minimize pumping action - Built-in bypass relief valve - Small handle spread

64 61 / 96 Compression Tools Hydraulic Compression tools / Manual PH-240 Manual / Hand operating - Output force: 6.2ton - Reservoir capacity: 55cc - Ram Stroke: 13mm - Max. Pressure: 550 bar - Crimping capacity: 240 mm 2 copper terminal 427mm 5.0kg - Plastic carry case - Standard Dies: 10/16,25/35,50/70,95/120,150/185,240 - Dies are sold separately - Accepts all dies used for Alcoa, Bundy, T&B, Klauke, Cembre, KUDOS, IZUMI 12 ton compressors. - Light weight, compact and slim design. - Pressure relief valve for overload protection. - Automatic low/high-pressure conversion with rapid/slow operating motion degree rotating head - External adjustable relief valve. - Two-stage hydraulic system reduces the number of pumps necessary.

65 62 / 96 Compression Tools Hydraulic Compression tools / Manual UCP-240 Manual / Hand operating - Output force: 8.8ton - Reservoir capacity: 118cc - Ram Stroke: 19mm - Max. Pressure: 700 bar - Crimping capacity: a. Hex. Crimping: s.q.mm b. Copper sleeves & lugs NFC s.q.mm c. Cu, Al bare or insulated sleevee54 - E230 d. Cu, Al sleeves & lugs DIN 48083KZ6 - KZ25 e. Pre-rounding s.q.mm 630mm ********************** 5.0kg - Plastic carry case - Standard Dies: 10/16,25/35,50/70,95/120,150/185,240 - Dies are sold separately swivel head - H-type head, easy to change dies - Twist handle pressure release - Two stage pumping action for rapid ram advance to the connector hold position with minimum pumping action

66 63 / 96 Compression Tools Hydraulic Compression tools / Manual CTE-412 Hand operating - Output force: 120kN - Ram Stroke: 30mm - Hexagonal crimping: Cu16-400mm² - Al16-300mm² - Rate Pressure: 68.8Mpa or 10,000 Psi 610(L)x150 (W) mm 6.2 kg - Plastic carry case Standard Dies: 16/25/35/50/70/95/120/150/185/240/ 300/400 ********************* FEATURES - Dies are sold separately. - Accepts all dies used for Alcoa, Bundy, T&B, Klauke, Cembre, KUDOS, IZUMI 12 ton compressors. - Two stage pumping active for rapid ram advance to the connector hold position with minimum pumping action. - Fiberglass handles suitable for 10KV hot line works degree swivel head

67 64 / 96 Compression Tools Hydraulic Compression tools / Manual HYCP-2612 Manual / Hand operating - Output force: 12ton - Reservoir capacity: 118.4cc - Ram Stroke: 26mm - Max. Pressure: 700 bar - Crimping capacity: 400 mm 2 copper terminal 490mm 6.0kg - Plastic carry case - Standard Dies: 10/16,25/35,50/70,95/120,150/185,240, 300,400 ********************************** - Dies are sold separately - Accepts all dies used for Alcoa, Bundy, T&B, Klauke, Cembre, Kudos, IZUMI 12 ton compressors swivel head - twist handle pressure release - Two stage pumping action for rapid ram advance to the connector hold position with minimum pumping action - Designed to accommodate U-type dies for applying compression fittings to copper, aluminum and ACSR conductor

68 65 / 96 Compression Tools Hydraulic Compression tools / Manual UB-412G Manual / Hand operating - C-framed crimping head for end and middle operation, opening 32mm, - Output force: 12ton - Crimping capacity: mm 2 - Reservoir capacity: 145cc - With window for oil quality inspection 590mm 7.0kg ACCESSERIES - Plastic carrying case - Standard Dies: 16/25/35/50/70/95/120/150/185/240/ 300/400 ************************** FEATURES - Accept for the Alcoa, Bundy, T&B, Klauke, Cembre and Blackburn 12ton crimping compressors - Manual press release device can control the pressure drag and Piston return - Crimping head can be turn for 180 for any of the work direction - Multiple oil supply speed up the Piston work - Fiberglass handle can afford the 20KV/3min voltage - External pressure governor easy to adjust the press power and convenience for daily tending - Hexagon, dot, circle crimping

69 66 / 96 Compression Tools Hydraulic Compression tools / Manual HYCP-4013 Manual / Hand operating - C-framed crimping head for end and middle operation, opening 38mm, EP510 opening 40mm - Output force: 130KN - Crimping capacity: mm x 160 x 70mm 6.42kg ACCESSERIES - Plastic carrying case - Standard Dies: 16/25/35/50/70/95/120/150/185/240/ 300/400 ************************** FEATURES - Accept for the Alcoa, Bundy, T&B, Klauke, Cembre and Blackburn 12ton crimping compressors - Manual press release device can control the pressure drag and Piston return - Crimping head can be turn for 180 for any of the work direction - Multiple oil supply speed up the Piston work - Fiberglass handle can afford the 20KV/3min voltage - External pressure governor easy to adjust the press power and convenience for daily tending - Hexagon, dot, circle crimping

70 67 / 96 Compression Tools Dies CTE-60S Compression Dies, 60ton, Compression dies are critical part of compressor and crimping tools for terminal and sleeve conductors, we do not have our own standard to meet each manufacturer s fittings, with detailed information and drawing of compression, we can produce the best quality dies to suitable for your request! The following is example of information which we need to make custom dies. Material of Terminal or sleeve. (Aluminum, copper, steel etc ) Fitting outer and inner diameter. Drawing of dies, groove dimension etc. Number or market of dies. Special request. DIES NO. A B C 10SH SH SH SH SH SH SH SH AH AH AH AH AH AH AH AH AH

71 68 / 96 Compression Tools Dies CTE-100A Compression Dies, 100ton Compression dies are critical part of compressor and crimping tools for terminal and sleeve conductors, we do not have our own standard to meet each manufacturer s fittings, with detailed information and drawing of compression, we can produce the best quality dies to suitable for your request! The following is example of information which we need to make custom dies. Material of Terminal or sleeve. (Aluminum, copper, steel etc ) Fitting outer and inner diameter. Drawing of dies, groove dimension etc. Number or market of dies. Special request. Avilable dies : FOR STEEL SLEEVES FOR COPPER LUGS FOR ALUMINUM SLEEVES DIES NO. A B C (100/200) S S S S /70 S /60 S /60 S /60 S S S S DIES NO. A B C (100/200) C C C C C C C C C C C C C C C C DIES NO. A B C (100/200) A /128 A /128 A /128 A /128 A /128 A /128 A /128 A /128 A /128 A /128 A /128 A /128 A /128 A /128

72 69 / 96 Battery Operated Tools Cable cutter REC-50 cable cutter (ratchet) - Charger Input: 120VAC, 50-60Hz, 21.75VA - Motor: 12V DC 345(H) mm 2.5kg - Plastic carry case - 12V nickel-cadmium cell - 110V or 230V DC charger *********************** - Ratchet function for pros and cons turn - Blade can be open totally for middle cut - guide sprocket in movable blade - Over load protection of auto shut up - Apply for one hand operation - Apply for the Low Voltage Distribution cutting Cut Capacity Polyethylene cable Multi-core vinyl insulation cable Soft copper cable Hard copper cable 600v-CV325 mm 2 (31mm OD) VVR150 mm 2 (47mm OD) 600V-CV150 mm 2 x 3 (46mm OD) 3core 600V-CV500 mm 2 (38mm OD) 6KV-CVT500 mm 2 (45mm OD) IV500 mm 2 (35mm OD) 150 mm 2 (21mm OD)

73 70 / 96 Battery Operated Tools Cable Cutter REC-54 cable cutter (ratchet) - Charger Input: 120VAC, 50-60Hz, 21.75VA - Motor: 12V DC 360(H) mm 4.0kg - Plastic carry case V nickel-cadmium cell - 110V or 230V DC charger *********************** - Ratchet function for pros and cons turn - Blade can be open totally for middle cut - guide sprocket in movable blade - Over load protection of auto shut up - Apply for one hand operation - Apply for the Low Voltage Distribution cutting Cut Capacity Polyethylene cable Multi-core vinyl insulation cable Hard Al. cable ACSR CCP-F-SS Hard copper cable 600V-CV325 mm 2 (31mm OD) VVR150 mm 2 (47mm OD) 3core HAL-OC400mm 2 ACSR MM OE-OC150 (31.9mm OD) mm mm 2 (21mm (18.6mm OD) OD)

74 71 / 96 Battery Operated Tools Cable Cutter REC-54AC cable cutter (ratchet) - Charger Input: 120VAC, 50-60Hz, 21.75VA - Motor: 12V DC 360(H) mm 4.0kg - Plastic carry case V nickel-cadmium cell - 110V or 230V DC charger *********************** - Ratchet function for pros and cons turn - Blade can be open totally for middle cut - guide sprocket in movable blade - Over load protection of auto shut up - Apply for one hand operation - Apply for the Low Voltage Distribution cutting Cut Capacity Polyethylene cable Multi-core vinyl insulation cable Soft copper cable Hard copper cable 600v-CV325 mm 2 (31mm OD) VVR150 mm 2 (47mm OD) 600V-CV150 mm 2 x 3 (46mm OD) 3core 600V-CV500 mm 2 (38mm OD) 6KV-CVT500 mm 2 (45mm OD) IV500 mm 2 (35mm OD) 150 mm 2 (21mm OD)

75 72 / 96 Battery Operated Tools Cable Cutter REC-65 cable cutter (ratchet) - Charger Input: 120VAC, 50-60Hz, 21.75VA - Motor: 12V DC 360(H) mm 4.0kg - Plastic carry case V nickel-cadmium cell - 110V or 230V DC charger *********************** - Ratchet function for pros and cons turn - Blade can be open totally for middle cut - guide sprocket in movable blade - Over load protection of auto shut up - Apply for one hand operation - Apply for the Low Voltage Distribution cutting Cut Capacity Polyethylene cable Multi-core vinyl insulation cable Soft copper cable Hard copper cable 600v-CV325 mm 2 (31mm OD) VVR150 mm 2 (47mm OD) 600V-CV150 mm 2 x 3 (46mm OD) 3core 600V-CV500 mm 2 (38mm OD) 6KV-CVT500 mm 2 (45mm OD) IV500 mm 2 (35mm OD) 150 mm 2 (21mm OD)

76 73 / 96 Battery Operated Tools Cable Cutter REC-85CCP cable cutter (ratchet), CCP cable - Charger Input: 120VAC, 50-60Hz, 21.75VA - Motor: 12V DC - Cutting capacity: mm 360(H) mm 4.0kg - Plastic carry case V nickel-cadmium cell - 110V or 230V DC charger *********************** - Ratchet function for pros and cons turn - Blade can be open totally for middle cut - guide sprocket in movable blade - Over load protection of auto shut up - Apply for one hand operation - Apply for the Low Voltage Distribution cutting

77 74 / 96 Battery Operated Tools Cable Cutter HEC-S26/45 Cable cutter - Input V.: 220VAC, 50-60Hz, - Input current: 21.75VA - Motor: 14.4 VDC, 2300 rpm - 2.6Ah 14.4VDC Battery - 120V OR 230VBattery Charger (optional) - Double molded carrying case - Shoulder strap **************************** - Lock pin type cutting head degree swivel head - Dies sold separately - Two stage action for a fast advancing speed - Pressure release is mechanism device, the piston can retract w/o electronic power - LED display indicates battery power condition and abnormal signal for protection - Ni-Mh battery, light weight, durable case, non-slip handle - Electronic speed control in trigger Type Output Reservoir Cutting capacity Size (L) Weight force capacity LGJ ACSR GL LJ&TJ Soft Rebar Wire Wire Wire (w/o twist Cu Al. steel rope rope rope battery) wire twist rod 6x7 6x12 6x19 HEC-S26 5.5ton 69cc 26mm 900 mm 2 20mm 26mm 20mm 16mm 18mm 24mm 24mm 405mm 4.0kg HEC-S ton 85cc 45mm 900 mm 2 20mm 45mm 20mm 16mm 22mm 25mm 25mm 425mm 6.12kg

78 75 / 96 Battery Operated Tools Cable Cutter HEC-C85 Cable cutter - Input V.: 220VAC, 50-60Hz, 21.75VA - Motor: 14.4 VDC, 2300 rpm - Output force: 5.6ton - Reservoir capacity: 125cc - Cutting capacity: Copper strands: Dia. 28mm Al strands: Dia. 38mm CCP cable: Dia. 85mm URD cable: 3x240 +1x95 mm 2 1x630 mm 2 General copper wire: 630 mm 2 Size: 505 x 345 x 89 mm ********************************* Weight 9.5kg w/o battery - 2.6Ah 14.4VDC Battery - 120V OR 230VBattery Charger (optional) - Double molded carrying case - Shoulder strap - Lock pin type cutting head degree swivel head - Dies sold separately - Two stage action for a fast advancing speed - Pressure release is mechanism device, the piston can retract w/o electronic power - LED display indicates battery power condition and abnormal signal for protection - Ni-Mh battery, light weight, durable case, non-slip handle - Electronic speed control in trigger

79 76 / 96 Battery Operated Tools Compression Tool HEC-U27 Compression, - Input V.: 220VAC, 50-60Hz, 21.75VA - Motor: 14.4 VDC, 2300 rpm - Output force: 12.7ton - Reservoir capacity: 85cc - Crimping capacity: L.V. Lugs & splices: 400mm 2 Insulated terminals: 240 mm 2 Cu sleeve connector: 185 mm 2 H.V. Lugs & Splices : 400 mm 2 Al. Lugs & splices: 300 mm 2 Size: 392 x 323 x 89 mm Weight 6.0kg w/o battery ***************************** - 2.6Ah 14.4VDC Battery - 120V OR 230VBattery Charger (optional) - Double molded carrying case - Shoulder strap - U-type head, accept deep stepped indent system of crimping - Dies sold seperately,180 degree swivel head - Two stage action for a fast advancing speed - Pressure release is mechanism device, the piston can retract w/o electronic power - LED display indicates battery power condition and abnormal signal for protection - Ni-Mh battery, light weight, durable case, non-slip handle - Electronic speed control in trigger

80 77 / 96 Battery Operated Tools Compression Tool HEC-32 Compression tool - Output Force : 12 Ton - Input V.: 220VAC, 50-60Hz, - Input current: 21.75VA - Motor: 14.4 VDC, 2300 rpm - Reservoir Capacity: 85 cc - Force at die face: 106kN - Crimping Capacity: Ø32mm, 400mm2 390 x 89 x 353mm 6.0 kg w/o battery *************************** - 2.6Ah 14.4VDC Battery - Battery Charger (optional) - Double molded carrying case - Shoulder strap - Standard dies: 50, 70, 95, 120, 150, 185, 240, 300 mm 2 - Apply for Alcoa, Bundy, T&B, Klauke, Cembre and Blackburn 12ton crimping die - 32mm jam opening C head degree swivel head - Dies sold separately - Two stage action for a fast advancing speed - Pressure release is mechanism device, the piston can retract w/o electronic power - LED display indicates battery power condition and abnormal signal for protection - Ni-Mh battery, light weight, durable case, non-slip handle - Electronic speed control in trigger

81 78 / 96 Battery Operated Tools Compression Tool REC-4412 Terminal Crimping - Output Force : 12 Ton - Ram Stroke: 30 mm - Motor: 14.4 VDC, 2300 rpm - Reservoir Capacity: 100 cc - Force at die face: 106kN - Capacity: Ø32mm, 300mm2 380 x 70 x 288mm 5.7 kg w/o battery - 3.0Ah 14.4VDC Battery - Battery Charger - Double molded carrying case - Shoulder strap ************************** - Apply for Alcoa, Bundy, T&B, Klauke, Cembre and Blackburn 12ton crimping die - 32mm jam opening C head degree swivel head - Dies sold separately - Built-in microchip to record number of crimps automatically - A built-in, preset bypass cartridge will kick out when the output reaches to 106kN - Manual pressure release button enable user to release pressure anytime during operation

82 79 / 96 Battery Operated Tools Compression Tool REC-4510 Terminal compression - Output Force : 13 Ton - Ram Stroke: 42 mm - Motor: 14.4 VDC, 2300 rpm - Reservoir Capacity: 135 cc - Force at die face: 106kN - Capacity: ψ32mm, 400mm2 425 x 80 x 260mm 7.26 kg w/o battery - 3.0Ah 14.4VDC Battery - Battery Charger - Double molded carrying case - Shoulder strap ************************** - Apply for Alcoa, Bundy, T&B, Klauke, Cembre and Blackburn 12ton crimping die - 32mm jam opening C head degree swivel head - Dies sold separately - Built-in microchip to record number of crimps automatically - A built-in, preset bypass cartridge will kick out when the output reaches to 106kN - Manual pressure release button enable user to release pressure anytime during operation

83 80 / 96 Battery Operated Tools Multi Function IS-MM20 Multi function tool - Charging time 60 min - Double Insulation - Power: 14.4VDC - Output force: 10ton - Ram stroke: 18mm 287 x 86 x kg ACCESSERIES Battery pack, Battery Charger, Carry case **************************** - Rotating head for any direction operation - One hand operation with one button control only - New electronic circuit board with LED indicates compression status and battery capacity - Universal install head design nut splitter, steel cut, angle steel cut, bend, punch, iron plate punch, cable cut NC19/25 NUT SPPLITTER Capacity: M16-M24 NC NUT SPLLITTER Capacity: M12-M24 PN STEEL CUTTER PC-18 Punch Thickness Dia.6=4mm Dia =7.5mm Dia.15.18=6mm PC-14 Punch Thickness: Dia.6=4mm Dia =7.5mm

84 81 / 96 Battery Operated Tools Rebar cutter IS-SC19L Rebar cutter, light weight, rapid speed - Output Force : 156.8kN - Motor: 19.2V DC - Charging time: 60min (50times) - Cutting Capacity: 19mm - Cutting speed: 6sec. 406 x 262 x 111mm 10.0kg w/i battery V Ni-MH Battery 2pcs - Battery Charger (optional) - Carrying case - Shoulder strap ************************** - Outside pressure testing device degree rotation in operation - Open-lock pin - Cutting head ensure 5000 times above quality cutting - Blade changeable in all direction - Operation handle design - Wide shoulder strap - Auto blade return after cutting, return device design

85 82 / 96 Battery Operated Tools Battery Pack BP-70Li Lithium-ion Battery Pack - Type: Lithium Ion - Output Voltage: DC14.4V - Capacity: 3000 mah 93 x 77 x 139 mm 550g ± 5g FEATURES - With fuel gauge - Anti-dust and rain-proof design - No memory Effect - Environmental Friendly - Light weight

86 83 / 96 Battery Operated Tools Battery Pack BP-70Hi NiMH Battery Pack - Type: Nickel-metal Hydride Battery - Output Voltage : DC14.4V - Capacity: 3000 mah 93 x 77 x 139mm 890g ± 5g - With Fuel Gauge - Anti-dust and rain-proof design - Environmental friendly - High Capacity

87 84 / 96 Battery Operated Tools Charger CH-70X Charger, For Li-ion, NiCr, and NiMH Battery Pack - Input Voltage: AC110~220V Auto-switching - Charging Voltage/Current: DC16.8V±0.05V/3.2A 195 X 110 X 75mm 660g ± 5g FEATURES - Refreshing function for deep discharging to prevent crystalline formation. - Fool Proof Design to avoid positive and negative electrode reverse. - Charging Time: 30min for NiCr battery, 45~60 min for Li-ion and NiMH Battery Pack.

88 85 / 96 Electronic Power Tools Multi-function IS-CP13 Multi-function tools - Output Force: 13ton - Output Voltage: AC220V - Capacity: M24 - Motor: 500W double insulation 72.5 x 320 x 212mm 4.8kg *************************** ACCESSERIES Carrying Case FEATURES - Head 360 rotating easy operation in confined space. - Double Insulation NC19/25 NUT SPPLITTER NC NUT SPLLITTER Capacity: M16-M24 Capacity: M12-M24 IS-A50C IS-A50V1 IS-A50B IS-A14P Capacity: L50x50xt6(SS400) Capacity: L50x50xt6(SS400) Capacity: L50x50xt6(SS400) Capacity: Φ14 t6(ss400) L50x50xt4(SUS304) L50x50xt4(SUS304) L50x50xt4(SUS304) Φ14 t4(sus304) Size: W162 x L150 x H246mm Size: W180 L245 H215mm Size: W120 L242 H117mm Size: W130 L380 H210mm Weight: 8.2kg Weight: 16kg Weight: 5.5kg Weight: 1.9kg

89 86 / 96 Electronic Power Tools Saw JIT-120A Saw - Motor: 220VAC 650W - Capacity: ψ120mm URD cable/ pipe - Saw Blade Size: 1140 x 0.65 x 13 mm (L x T x W) - Saw blade type: Standard: 18/24 teethes High Speed Steel: 18/24 teethes 50x22x20cm 5.9 kg - Various saw blade available on request - Apply for the underground cable operation - Light weight and easy to operate - H-L speed for different material cut

90 87 / 96 Hydraulic Nut Splitter Nut Splitter Head HYNC-XX Nut Splitter Head FEATURES - Compact and Seven style nut splitters - Single active piston spring return - Accept for any kinds of the 700bar (10,000psi)hydraulic pump REMARKS - Nut hardness not more than HRC-44 - Cannot use for stainless or square nuts Model No. Bolt Size Hex. Nut Output Length Width Height Weight Size (mm) Force (ton) (mm) (mm) (mm) HYNC 1319 M6 M HYNC 1924 M12 M HYNC 2432 M16 M HYNC 3241 M22 M ************************** HYNC 4150 M27 M HYNC 5060 M33 M HYNC 6075 M39 M

91 88 / 96 Pump Hand Operated HP-700A Manual / Hand operated - hydraulic fluid flow: low press 12.26cc a time high press 2.26cc a time - Oil volume required: 720cc 660(L) x 135 x 170(H) mm 8.3kg (w/o oil hose) - 2m hydraulic hose attached - Plastic carry case - Addition press gauge (optional) ************************ FEATURE: - Two stage pimping acting for rapid ram advance - Replaceable dropout bypass valve cartridge for easy repair - Economical yet dependable hand hydraulic pump

92 89 / 96 Pump Foot Operated HYP-700FT Foot operated - Hydraulic fluid flow: low press 12.26cc a time high press 2.26cc a time - Oil volume required: 720cc 710(L) x 192(W) x 190(H) mm 12.7kg (not including oil pipe) - 2m hydraulic hose attached - Plastic carry case - Addition press gauge (optional) ************************ FEATURE: - Two stage pumping system for rapid ram advance - Replaceable dropout bypass valve cartridge for easy repair - High-low multiple oil supply - Safety Valve, auto press release when reach the setting degree - For any of direction operation, even head upward

93 90 / 96 Pump Hydraulic pump SGS-2 Single acting, small size - These pumps' excellent portability, made possible by small size and light weight, as well as their durability, make them a versatile choice for many uses including electrical contracting, civil engineering, and plumbing work. - The units are operated by a reliable remote control equipped with a solenoid valve, and equipment types can be chosen according to the type of control. - The SGS-2-C is capable of inching for fine control, making it optimum for jobs like pipe bending and straightening. - The SGS-2-O is for auto-return operation, and is good for tasks such as terminal crimping, cutting, and riveting. * The SGS-2 is single-acting only, and cannot be used with double-acting cylinders. ************************ Specifications/Model Motor Pressure Discharge rate High Low High Low SGS-2-C(0) AC100V/220V 0.3kw 3.Phase 70 Mpa (720kgf/cm2) 1.5 Mpa (15kgf/cm2) 0.25L/min 2L/min Reservoir 2.5L Weight 13kg

94 91 / 96 Pump Hydraulic Motor Operating R14E-R Electric Motor Operated - Oil delivery: 2.6 Liter /min at low pressure 0.32 Liter/ min at high pressure - Rate Pressure: 68.8Mpa or 10,000 Psi - Input: Single phase 50/60 Hz 120V or 230v 300W motor - Reservoir capacity: 2.0 Liter 250(L) x 160(W) x 355(H)mm 15.0kg (13.0kg dry) - 3m Cable remote control - 2m hydraulic hose attached - Pressure gauge FEATURE: - Two stage pumping system for rapid advance - Adjustable out put pressure to 68.5 Mpa degree swivel joint for hose maneuverability - Visual oil level - Steel housing to protect motor

95 92 / 96 Pump Hydraulic Motor Operating P300S Single acting power pack - Oil delivery: 1.5 Liter /min at low pressure 0.3 Liter/ min at high pressure - Rate Pressure: 68.8Mpa or 10,000 Psi - Input: Single phase 50/60 Hz 230VAC 300W - Reservoir capacity: 2.0 Liter 235(L) x 190(W) x 345(H)mm 17.0kg - 3m Cable remote control - 2m hydraulic hose attached - Pressure gauge FEATURE: - Two stage pumping system for rapid advance - Adjustable out put pressure to 68.5 Mpa - Visual oil level - Aluminum housing to protect motor

96 93 / 96 Pump Hydraulic Pump / High Pressure D-XW High-pressure D-3SW D-2SW-4 D-1SW-4 1SW-40 ************************ Specifications/model D-3SW D-2SW-4 D-1SW-4 1SW-40 AC380V 50Hz AC380V 50Hz AC380V 50Hz AC230V 50Hz Motor 2.2kw 1.5kw 0.75kw 0.4kw - These high-pressure hydraulic pump units, which feature superior durability despite their small size and light weight, have an excellent track record of about 40 years serving in demanding applications as hydraulic punchers, and working under harsh conditions including civil engineering projects and foundries. - The single-piece rotor shaft shows its strength in repeated starting and stopping.* - Our wet-type solenoid valve (S-D4-SGS-AHB), which has extremely small leakage, suppresses heat generation and helps our high-efficiency pumps do their jobs.* - To ensure safety, pumps with three-position, four-way solenoid valves have 24 VAC local control circuits. - We will attach manual changeover valves, pressure gauges, pressure switches, and other components, and change pumps to your desired circuits. Pressure 3Phase 3Phase 3Phase 3Phase H 72MPa(740kgf/cm2) L 7MPa(70kgf/cm2) 3MPa * The 1SW-40 has a split shaft and is equipped with a dry-type solenoid valve. H 2.3L/min 1.5L/min 0.75L/min 0.3L/min Discharge rate* L 5.8L/min 3.75L/min 3.75L/min 1.9L/min Reservoir 12L 10L 7.5L 5L Weight 65kg 55kg 38kg 28kg Solenoid-Valve 3-Position,4-way 2-Position, 4-way Technical note: Hydraulic pumps develop the same pressure despite their different sizes. The only difference is the discharge rate; a larger rate means you can work faster.

97 94 / 96 Pump Hydraulic Engine Operating SEP5-1 For 60, 100 & 200 ton presses - Oil delivery: low pressure 0-20bar: Liter /min high pressure bar: 2.41 Liter/ min - Rated Pressure: 68.8Mpa or 10,000 Psi - Engine: Air cooled - 4 cycle gasoline engine kw (5ps) /3600rpm. Lead free gasoline - Reservoir capacity: 9.5 Liter 590(L)x430(W)x520(H)mm 58.0kg - Spark plug wrench - Exhaust cup FEATURE: - Hydraulic hose sold separately - For double and single acting tools - Positive manual control valve

98 95 / 96 Pump Hydraulic Engine Operating HPE-3ST Single acting - Oil delivery: 0-20kgf/cm2 or 1.10 liter /min at low pressure kgf/ cm2 or 3.30 liter/ min at high pressure - Engine: Air cooled 4 cycle gasoline engine - 2.0kw (2.7ps)/ 3,600 rpm, lead-free gasoline - Reservoir capacity: 5 liter - Rated Pressure: 68.5 Mpa or 10,000 psi 650 (L) x 500 (W) x 370(H)mm 52kg - Air Wheels (optional) - Hydraulic hose (optional) FEATURE: - External fluid flow control - Wired remote control operation with manual control level - Compression counter to monitor compression cycles for the remainder of maintenance schedule - Pressure gauge for easy output confirmation - Reliable output by FUJI HEAVY S engine

99 96 / 96 Pump Hydraulic Engine Operating HPE-3DT Double acting - Oil delivery: 0-20kgf/cm2 or 1.10 liter /min at low pressure kgf/ cm2 or 3.30 liter/ min at high pressure - Engine: Air cooled 4 cycle gasoline engine - 2.0kw (2.7ps)/ 3,600 rpm, lead-free gasoline - Reservoir capacity: 10 liter - Rated Pressure: 68.5 Mpa or 10,000 psi 660 (L) x 500 (W) x 370(H)mm 55kg - Air Wheels (optional) - Hydraulic hose (optional) FEATURE: - External fluid flow control - Wired remote control operation with manual control level - Compression counter to monitor compression cycles for the remainder of maintenance schedule - Pressure gauge for easy output confirmation - Reliable output by FUJI HEAVY S engine