8.0 PARTS LIST - MP2500iX ELECTRIC PUNCH

Transcription

1

2 8.1 Parts Listing, Machine Front Assembly SCREW, 8-32 x.75 PHIL PAN HEAD SCREW, x 1.0 F.H. SOCKET SCREW PLASTIC RIVET ENDCAP, RIGHT ENDCAP, LEFT DECK, BACK DECK, FRONT SWITCH, START PLATE, EDGE GUIDE ADJUSTMENT PCB, LED, MODULAR PUNCH LABEL, BLACK WIRE RETAINER LABEL, MAIN DECK LED BOARD COVER CABLE ASSEMBLY, RUN SWITCH CABLE ASSEMBLY, LED BOARD 1 Page 8-3

3 8.2 Parts Listing, Power Switch Assembly FUSE HOLDER, 115V FUSE HOLDER, 230V SCREW, 6-32 x.38 SLOT HEX HD NUT ½ NUT, 6-32 KEPS FUSE, 3A, 250V (for use with 115V model) FUSE, 2 A, 250V (for use with 230V model) LABEL, FUSE, 3A, 250V LABEL, FUSE, 2A, 250V SOCKET, POWER LINE, RFI FILTER 115V & 230V SWITCH, PNEUMATIC BRACKET, ELECTRICAL MOUNTING ROCKER SWITCH 1 Page 8-4

4 Figure MP2500iX Parts Page 8-5

5

6

7 Figure MP2500iX Parts Page 8-8

8 8.3 Parts Listing SET SCREW, CUP, x 3/ SCREW, x 2.25 S.H.C SHOULDER BOLT SCREW, ¼ - 20 x 5/8 HX CAP W/NYLOCK SCREW, 5/16-18 x.50 FLANGELOCK SCREW, x 11/16 SEMS HX WSH HD TAP SCR SCREW, x.50 ST HEX HD SCREW, x 1.0 ST HEX HD SCREW, x.63 ST HEX HD SCREW, x.50 ST HEX HD SCREW, 8-32 x.75 PHIL PH HARDENED WASHER ID x.63 OD NUT, KEPS CABLE CLAMP STRIP, EDGE CORD RETAINING RING TIE WRAP GREASE, LUBRIPLATE #130 AA OIL, GENERAL PURPOSE CITCO CAPACITOR 35UF, 115V CAPACITOR 230V BRACKET, CAPACITOR CABLE, GROUND (PART OF WIRE KIT) PIVOT PIN, CRANK GUIDE MOTOR MTG BRKT HOUSING ASSEMBLY, WITH LABELS 115V HOUSING ASSEMBLY, WITH LABELS 230V BASE ASSEMBLY, MACH. & PAINT PAD, ANTI-ROTATION GUIDE, CHIPTRAY DETENT, DIE SET, MOD PUNCH DEFLECTOR, MODULAR PUNCH EDGE GUIDE KNOB, EDGE GUIDE SPRING, CHIPTRAY FOOT, MP2500iX 2 Page 8-6

9 8.3 Parts Listing WASHER, PRESSURE BAR, PLASTIC CRANK, 5/8 SHAFT SLIDE, DIE SET, FRONT CHART, FINAL DIESET ASSEMBLY MOD PNC MACHINE FRONT ASSEMBLY LINKAGE ASSEMBLY PRESSURE BAR ASSEMBLY POWER SWITCH ASSEMBLY PCB ASSEMBLY CHIP TRAY ASSEMBLY HOME SWITCH ASSEMBLY SLIDE INTERLOCK SWITCH ASSEMBLY GEAR MOTOR W/SOLE BRAKE 115V GEAR MOTOR W/SOLE BRAKE 230V Z SUPPORT BRACKET CABLE ASSEMBLY, LINE CABLE ASSEMBLY, NEUTRAL CABLE ASSEMBLY, A.C CABLE ASSEMBLY, D.C CABLE ASSEMBLY, TRAY SWITCH CABLE ASSEMBLY, DIESET/FOOT/HOME CABLE ASSEMBLY, INPUT/MOTOR BRAKE WIRE KIT, CABLE ASSEMBLY, ITEM #22, Page 8-7

10 8.4 Parts Listing, PCB Assembly Bracket SCREW, 8-32 x.63 PHIL PH SCREW, 4-40 x.63 PHIL PH SCREW, 4-40 x.25 PHIL PH, SEMS NUT, 4-40 KEPS P.C.B. SUPPORT POWER SUPPLY SWITCH INSULATOR, CHIPTRAY BRACKET, PCB PC BOARD FOOT, MP2500iX 4 Page 8-8

11 8.5 Parts Listing, Slide Interlock Switch Assembly SCREW, 2-56 x.5, PHIL PH SNAP SWITCH SWITCH COVER PLATE SLIDE, DIE SET, BACK INSULATOR, SUBMINATURE SWITCH 1 Page 8-9

12 8.6 Parts Listing, Pressure Bar Assembly SCREW, x.63 SLOT HEX HD W/ SEMS NUT, KEPS RACK, PRESSURE BAR STRIPPER BRACKET, UPPER STRIPPER BRACKET, LOWER PRESSURE BAR, WELDMENT 1 Page 8-10

13

14 8.7 Parts Listing, Linkage Assembly KEY, CONNECTING CRANK RETAINING RING SHAFT, DRIVE CONNECTING LINK PIVOT PIN, SHAFT CONNECTING CRANK SPACER, CONNECTING CRANK LUBRIPLARE #130-AA.01 Page 8-12

15 8.8 Die Set Parts Listing (Die Set not shown) Part Number Description Qty FELT PAD, OILED MAGNET, FELT PAD RETAINING PUNCH PIN, PB PUNCH PIN, C PUNCH PIN, W3 SQUARE PUNCH PIN, W3 ROUND PUNCH PIN, W2 SQUARE PUNCH PIN, W2 ROUND PUNCH PIN, VELOBIND PUNCH PIN, SUREBIND PUNCH PIN, LOOSE LEAF, 2-4 / Die Set repair is not recommended other than to clean and lubricate the Punch Pins. Punch pins are listed here as a service item only in the event that some may be lost. If a Die Set produces poor hole quality over time, it is more likely a result of Die Plate wear. In this case the Die Set should be replaced with a new one. 8.8 Complete Die Set Assemblies including shipping carton Part Number Description DIE SET, PB DIE SET, C4 GBC DIE SET, W3 ROUND DIE SET, W3 RECTANGULAR DIE SET, W2 ROUND DIE SET, W2 RECTANGULAR DIE SET, LOOSE LEAF 3-5-7/ DIE SET, SB DIE SET, VB Page 8-13