Qty: 1B40 1,2 958lm/10.4W per foot 1B B lm/6.8W. per foot. 2B lm/15.4W per foot. 2B lm/10.2W per foot. 2B lm/18.

Transcription

1 Date: Customer: Project: Type: Qty: Survivor 9 LED Order Code: SUR9L SUR9L Series Light Engine SUR9L Survivor 9 LED 1B45 1,2, 1060lm/11.7W 2B45 1,2, 2113lm/23.6W 1B40 1,2 958lm/10.4W 2B40 1,2 1910lm/21.0W 1B lm/9.1W 2B lm/18.4W 1B lm/7.6W 2B lm/15.4W 1B lm/6.8W 2B lm/13.6W 1B lm/5.0W 2B lm/10.2W Values calculated from a 4 using DIM driver. 2 Not available with Lutron CCT K Shielding PC Polycarbonate Prismatic Satine Lens K K LI Polycarboate Prismatic Satine Lens with LED optimized inlay K Mounting F V 3 Surface Mount Vertical Wall Mount Mount RS 4 Rigid Stem Mount 3 No hinges included 4 No Feed Location Required Feed Location *Not required for RS mounting RF 5 Right Feed LF 5 Left Feed VF 6 Vertical Feed (feed at bottom) BF Back Feed EL End Feed Left (for conduit) ER End Feed Right (for conduit) ED 7 End Feed both sides (for conduit daisy chain) 5 F mounting only. 6 V mounting only. 7 Fixture not rated for use as a raceway. Nominal Length 02 2 ft ft ft. XX 8 Run, available in 2, 3 or 4 nominal increments. Round up to the nearest foot and replace the XX with the footage (i.e. 16 for 16 ) 8 Requires NC option. Finish WH White BK Black BZ Bronze SV Silver SP Specify Premium Color Custom colors are available, Please consult factory Voltage UNV 120 thru /60hz capable Volt Volt 9 Available only with 1B35 and 2B35 light engines, using DIM, DIL, and DC3 drivers. Driver DIM 0-10V (Linear) DIL 0-10V (Logarithmic) DED eldoled ECOdrive DALI (Logarithmic) DC2 Lutron 2-Wire DC3 10 Lutron 3-Wire DCE 10 Lutron Eco-System DC5 Lutron 5-Series (consult factory) SR 11 Philips Xitanium SR (DALI) 10 Available only for 1B35 11 For use with external sensors, by others Fixture Options FS 12 Single Fusing NC 13 Nipple Connector (for Runs) TR Tamper Resistant Door Screws EFC End Feed for 1/2 conduit NF Natatorium Finish (consult factory) 12 Not available with 347V or 480V 13 Required for Runs Emergency Options EC 14 Emergency Circuit Wiring EMR Remote Micro Inverter (consult factory) 14 See page for full details and restrictions 5YEAR LED WARRANTY ARRA Compliant ADA Compliant Page 1 of 8

2 Surface Mount (F) Vertical Wall Mount (V) Rigid Stem (RS) 2 13 /16 (71mm) 9 1 /2 (240mm) Construction: Housing - Low profile marine-grade, extruded aluminum housing with low-copper, die cast aluminum end caps and stainless steel mounting brackets. Designed for indoor and outdoor wall and ceiling mount applications as well as light to medium security areas. Mounting hardware by others. Geartray - Gear tray installs as complete electrical unit secured with a spring clip assembly fully accessible from below ceiling. White finish for even illumination. Shielding - Vandal and impact resistant.156 thick polycarbonate prismatic satine lens (IK10, NRTL, & IP66 wet label certificate ratings). One piece Silicone Gasketing - Fixture lens and end plates are fully gasketed (IP66 rated) for weather proofing, dust, and insect control. Hinged Lens Door - Door hinges down on surface and rigid stem mount versions for easy access to lamp(s) and driver. Hinges are replaced with safety cable for Vertical Wall Mounting. After door is open, hinges can be released via a quick disconnect mechanism for easy mounting of housing. Door seals securely with two (2) vandal resistant stainless steel captive fasteners when TR option is selected. Feed Location - (not required for RS Mounting.) For Surface Mount (F), specify Left (LF) or Right (RF) side for power feed entry. For Vertical Wall Mount (V), Feed Location is availalable with Vertical Feed (VF) or Back Feed (BF). For mounting over junction box, please specify (BF) option and see page 3 for details. Consult factory for middle fixtures to be connected in a linear row with nipple connector. Nipple Connector - (not shown) 3/8 IP nipple connector for water tight connection between luminaires in a run. Two connectors required per connection. Not required when MT is used. Weight - 2 ft - 12 lbs., 3ft - 18 lbs., 4ft - 24 lbs. Electrical/Performance: LED Light Engine - Brand-name mid-power LEDs create a high efficiency LED light engine able to provide a lumen maintenance of 96% at 25,000 hours and 93% at 60,000 hours for 1B light engine and 96% at 25,000 hours and 93% at 60,000 hours for 2B light 25ºC per TM-21 reports. Reported L70 greater than 60,000 hours. Delivered Lumens - Due to LED manufacturer s tolerances the listed output has a ±5% tolerance. For outputs based on different shielding or CCT please see photometry section at the end. CCT - Available in 2700K, 3000K, 3500K and 4000K, tolerance within a 3-step MacAdam ellipse. CRI - Min. 90. All Drivers - High efficiency, constant current, soft start, Electronic Class 2 with a PFC > For more detailed information on the available drivers please see page 7. Sensors - Selux offers a variety of integral sensor options. For details and specifications, please refer to page 9. Thermal Performance: Ambient Operating Temperature - Luminaires suitable for maximum ambient temperature of 35 C (95 F) for all drivers. Luminaires are suitable for minimum ambient temperatures of: -40ºC (-40ºF) for DIM, DM, DML, and DMD drivers. -20ºC (-4ºF) for SR drivers. 0ºC (32ºF) for DC2, DC3, and DCE drivers. Luminaire Finish: Powder Coat - All Selux luminaries are finished in high quality polyester powder coating in our Tiger Drylac certified facility and are tested in accordance with test specifications for coatings from ASTM and PCI. All products undergo a five stage intensive pretreatment process where product is thoroughly cleaned, phosphated, and sealed. Selux powder coated products provide excellent salt and humidity resistance as well as ultra violet resistance for color retention. Standard interior colors are White (WH), Black (BK), Bronze (BZ), and Silver (SV). Selux premium colors (SP) are available, please specify from your Selux color selection guide. Warranty: 5 Year Limited LED Luminaire Warranty - Selux offers a 5 Year Limited Warranty to the original purchaser that the Survivor 9 LED s assembly shall be free from defects in material and workmanship for up to five (5) years from date of shipment. This limited warranty covers the LED driver and LED light engine when installed according to Selux instructions and operated within the Ambient Temperature. For additional details and exclusions, see Selux Terms and Condition of Sale. Certifications and Compliance: NRTL - For Wet location (I.E. culus; ccsaus) ARRA Compliant RoHS Compliant Page 2 of 8

3 Surface Mount Right/Left/Vertical Feed For mounting over a juction box. Suggested mounting with hinges on bottom edge of fixture. Please note: for vertical mounting, the feed is on the bottom and hinge is replaced by stainless steel safety cable. Mounting hardware by others. Outlet box by others. Top View Front Closed View Survivor 9 LED Surface Mount 1L35 or 2L35 Mounting Length 9 1 / 2 (240 mm) 1 7 / 16 (36 mm) Feed Hole Feed Cable Side View 2 individual 3 individual 4 individual 27 3/16 (690mm) 39 13/16 (995mm) 51 3/16 (1300mm) 25 5/8 (651mm) 37 5/8 (956mm) 49 5/8 (1261mm) Front View (w/o cover/geartray shown) Left Feed Location (LF) Feed cord provided equivalent to length of fixture. (4x) Clearance holes for up to 1 / 4 (6mm) mounting hardware (by others) 6 22 / 32 (170 mm) Feed Cord in Right Feed Location (RF). Cord run through channel in back of housing. Driver Mounting Length Hinged Edge (Horizontal mountings only) Surface Mount / Vertical Mount Back Feed For mounting to a juction box. Suggested mounting with hinges on bottom edge of fixture. Mounting hardware by others. Outlet box by others. IMPORTANT! Feed Hole is not centered. J-Box by others must be offset accordingly. Top View Survivor 9 LED Surface Mount 1L35 or 2L35 Front Closed View 9 1 / 2 (240 mm) 1 7 / 16 (36 mm) Side View 2 individual 3 individual 4 individual 27 3/16 (690mm) 39 13/16 (995mm) 51 3/16 (1300mm) Mounting Length 25 5/8 (651mm) 37 5/8 (956mm) 49 5/8 (1261mm) Front View (w/o cover/geartray shown) 13 / 16 (21mm) Feed Hole suitable for 1 / 2 (13mm) chase nipple for water-tight connection to J-Box (4x) Clearance holes for up to 1 / 4 (6mm) mounting hardware 1 7 / 8 (47.6mm) 6 22 / 32 (170 mm) 3 / 4 (19.5 mm) 4 (101.6 mm) Driver 1 3 / 8 (35mm) Mounting Length 3 / 4 (19.5mm) Hinged Edge of Housing (Horizontal mountings only) For other lengths, lamping, continuous runs or configurations, please specify overall length (in feet), accessories desired and sketch/drawing of configuration. Selux will detail project drawings upon order and supply submittal drawings for approval. Individual fixtures cannot be field joined without NC option. If you have any questions please contact Selux customer service or applications engineering for assistance (1-800-SELUX-CS). Page 3 of 8

4 Rigid Stem Mount with 5/8 powder coated steel pipe, threaded on both ends. Side View Feed Suspension Points 4 (1219mm)Height 2 individual Survivor 9 LED Rigid Stem Mount 1L35 or 2L /16 (690mm) Suspension Points 25 5/8 (651mm) 3 individual 4 individual 39 13/16 (995mm) 51 3/16 (1300mm) 37 5/8 (956mm) 49 5/8 (1261mm) Rigid Stem (RS) Suspension Detail 6 ft. of feed cord pre-attached to luminaire 3/8 I.P. Nipple (supplied and installed by others) Outlet Box (supplied and installed by others) Suspension Hickey Hex Nut 1/4 x 5 Diameter Canopy (White) Canopy Securing Collar 3/4 Diameter Steel Stem (White) Dress Nut Hex Nut Page 4 of 8

5 Drivers: 0-10V linear dimming (DIM) Luminaires supplied with drivers offering the capability of either normal switched operation or 0-10V dimming for linear dimming curve. Fixtures ship wired for dimming. For on/off functionality, simply cap the dimming leads. Minimum dimming level preset at factory to 1%. eldoled SOLOdrive 0-10V linear dimming (DM) Luminaires supplied with SOLOdrive 0-10V dimming driver for linear dimming curve. Minimum dimming level preset at factory to 1%. For dim to dark (down to 0.1%), please consult factory. eldoled SOLOdrive 0-10V logarithmic dimming (DML) Luminaires supplied with SOLOdrive 0-10V dimming driver for logarithmic dimming curve. Minimum dimming level preset at factory to 1%. For dim to dark (down to 0.1%), please consult factory. eldoled SOLOdrive DALI dimming (DMD) Luminaires supplied with SOLOdrive DALI dimming driver for logarithmic dimming curve. Minimum dimming level preset at factory to 1%. For dim to dark (down to 0.1%), please consult factory. * For control recommendations for eldoled drivers, please consult eldoled. LUTRON 2-wire dimming (DC2) Luminaires supplied with Hi-lume 2-wire dimming driver programmed for Constant Current Reduction (CCR). For Pulse Width Modulation (PWM) dimming, please consult factory. Minimum dimming level down to 1%. LUTRON 3-wire dimming (DC3) Luminaires supplied with Hi-lume 3-wire dimming driver programmed for Constant Current Reduction (CCR). For Pulse Width Modulation (PWM) dimming, please consult factory. Minimum dimming level down to 1%. LUTRON EcoSystem dimming (DCE) Luminaires supplied with Hi-lume EcoSystem (4 wire, digital link) dimming driver programmed for Constant Current Reduction (CCR). For Pulse Width Modulation (PWM) dimming, please consult factory. Minimum dimming level down to 1%. LUTRON EcoSystem 5-Series dimming (DC5) Luminaires supplied with EcoSystem 5-Series dimming driver programmed for Constant Current Reduction (CCR). For Pulse Width Modulation (PWM) dimming, please consult factory. Minimum dimming level down to 5%. * For control recommendations and system layout for Lutron drivers, please contact Lutron. Philips Xitanium Sensor Ready DALI dimming (SR) Luminaires supplied with Xitanium SR dimming driver programmed for Constant Current Reduction (CCR). Minimum dimming level down to 5%. For use with E and P sensors only. Driver Quantity 2 ft. 3 ft. 4 ft. RUN DIM, DIL, DED, and SR drivers Approximately 1 driver per 4 ft. DC2, DC3, DCE, and DC5 drivers Consult Factory *For inrush and control current, please refer to the driver manufacturers spec sheets. Wiring Diagrams 0-10V linear (DIM) 0-10V linear eldoled SOLOdrive (DM) 0-10V logarithmic eldoled SOLOdrive (DML) DALI eldoled SOLOdrive (DMD) Philips SR DALI (SR) DIM, DM, DML, DMD & SR DALI DALI standard DCE & DC5 Lutron EcoSystem 5-Series (DC5) Page 5 of 8

6 Options Typical Spacing for Runs Create Run by adding individual luminaires with NC option. If different lengths are chosen, the shortest housing is placed at the end. For example: for an 11ft run, the following length luminaires would be used 4ft - 4ft - 3ft Connector Assembly Detail with Hex Nuts, Connector and O rings. Water-tight Threaded Nipple supplied by manufacturer with lock-nuts. 1 /8 (3mm)gap (minimum) Conduit Connector Used with the EL/ER/ED feed options. For 1/2 conduit only. Connector Assembly Detail with Hex Nut, O ring and Connector. Single Fusing Fusing, fixture(s) supplied with an in-line fuse (up to 277v) located on the hot wire for each feed. (Min. 3amp to a Max. 6amp slow burn fuse). Tamper Resistance Tamper Resistant option (TR) uses tamper resistance assembly and door screws. For other lengths, lamping, continuous runs or configurations, please specify overall length (in feet), accessories desired and sketch/drawing of configuration. Selux will detail project drawings upon order and supply submittal drawings for approval. Individual fixtures cannot be field joined. If you have any questions please contact Selux customer service or applications engineering for assistance (1-800-SELUX-CS). Page 6 of 8

7 Photometry LI /4000K CCT Catalog #: SUR9L-1B35-40-LI-X-04-XX-UNV Report #: Delievered Lumens: 3372 Input Watts: 36.52W Efficacy: 92 Power Factor: Total Harmonic Distortion: 3.43 CCT: 3940K CRI: 96.2 Max Candela: from Vertical Spacing Criterion (0-180): 1.16 Spacing Criterion (90-270): 1.22 Spacing Criterion (Diagonal): 1.28 Maximum Candela = 1314 Located At Horizontal Angle = 22.5, Vertical Angle =.5 # 1 - Vertical Plane Through Horizontal Angles (90-270) # 2 - Vertical Plane Through Horizontal Angles (0-180) 1 2 PC /4000K CCT Catalog #: SUR9L-1B35-40-PC-X-04-XX-UNV Report #: Delievered Lumens: 3702 Input Watts: 36.45W Efficacy: 102 Power Factor: Total Harmonic Distortion: 3.43 CCT: 3940K CRI: 96.2 Max Candela: from Vertical Spacing Criterion (0-180): 1.20 Spacing Criterion (90-270): 1.24 Spacing Criterion (Diagonal): 1.32 Maximum Candela = 1382 Located At Horizontal Angle = 22.5, Vertical Angle =.5 # 1 - Vertical Plane Through Horizontal Angles (90-270) # 2 - Vertical Plane Through Horizontal Angles (0-180) 1 2 Page 7 of 8

8 Photometry 4000K 3500K 3000K 2700K Light Engine Lumens Wattages 1B B B B B B B B B B B B LI PC SUR9L LED Direct Photometry Multiplier Table CCT Multiplier Light Engine Multiplier Lens Multiplier CCT and CRI multipliers apply to the photometry, IES files, and values listed on page one (light engine). Light engine multiplier supplied for values listed on page one (light engine). Page 8 of 8