1 With internal stepdown transformer 26 7 /8" (683mm)

Transcription

1 Project: Type: _ RRSL L55 Series Mounting Height Light CCT Finish Voltage Engine Options Qty: Series RRSL Ritorno Round Symmetrical LED Mounting Height Light Engine CCT Finish Voltage Options 1 Single W Wall Mount RP10 RP12 RP14 RP16 10 ft. 12 ft. 14 ft. 16 ft. L55 55W WH White BK Black BZ Bronze SV Silver SP Specify Premium Color With internal stepdown transformer 2 Only 120/277 REC GFCI Receptacle (pole mount only) DM Dimming (0-10V) HL 2 Hi-Lo Switching MS Motion Sensor with Optional Photocell (meets Title 24 requirements) *See page 2 for order code Reflective Shade /8" x 35 3 /4" (683mm x 908mm) minimum 3/16" (4.7mm) thick aluminum reflector shade painted white for maximum reflectivity. Supplied with drip groove around perimeter, to prevent rain marks on underside. Shade attached to fixture arms with low profile stainless steel hardware. 2. Fixture Arms - Three natural, marine grade stainless steel with bead-blasted finish, rigidly attach reflector shade to pole fitter. TEL (845) FAX (845) RRSL (ss-v1.4) 35 3 /4" (908mm) NRTL Listed (i.e. UL, CSA) Union Made Affiliated with IBEW Local /8" (683mm) 3. Housing Cover - Heat-tempered flat glass lens protects LED light engine assembly. Continuous molded silicone gasket creates sealed optic chamber for weather proofing, dust and insect control. Door pivots open from housing chamber for servicing. Three captive stainless steel screws secure lamp cover in position. 4. LED Light Engine - (not shown) High efficacy LED light engine with 60,000 hour+ life until L70. Available with 3000K, 3500K or 4000K CCT and a CRI of 80. IP65 5. Optics - (not shown) Symmetric reflector and tempered flat glass lens focus lumen output on secondary reflector shade. Secondary reflector shade redirects light for even illumination without shadows. 6. LED Driver - (Not shown) High power factor, High efficiency constant current LED driver VAC input. Protection class IP Surge Protection - (Not shown) 3-Pole Surge protection device safeguards electrical components from indirect lighting strikes and surges up to (10kA and 10kV). 8. Pole Fitter - Die cast aluminum fitter secures fixture arms and reflective shade to pole. Tapered to continue lines from pole. 9. Pole - Pole to be aluminum and taper from 5" diameter at the bottom to 7" diameter at the top. Pole wall thickness to be minimum thick, supplied with a 3" x 5" hand hole, with cast 356 aluminum tempered to a T6 condition reinforced frame, with integral ground lug connection and gasketed flush fitting door. 10. Base Cover - (not shown) Std. two-piece base cover is made from die-cast 356 alloy aluminum which is heat treated to produce a T6 temper, measuring 4 1 /2" (115mm) height by 12 1 /2" (316mm) diameter. Exterior Luminaire Finish - Selux utilizes a high quality Polyester Powder Coating. All Selux luminaires and poles are finished in our Tiger Drylac certified facility and undergo a five stage intensive pretreatment process where product is thoroughly cleaned, phosphated and sealed. Selux powder coated products provide excellent salt and humidity resistance as well as ultra violet resistance for color retention. All products are tested in accordance with test specifications for coatings from ASTM and PCI. Standard exterior colors are White (WH), Black (BK), Bronze (BZ), and Silver (SV). Selux premium colors (SP) are available, please specify from your Selux color selection guide. 5 Year Limited LED Luminaire Warranty - Selux offers a 5 Year Limited Warranty to the original purchaser that the Ritorno LED luminaire shall be free from defects in material and workmanship for up to five (5) years from date of shipment. This limited warranty covers the fixture, LED driver and LED light engine when installed and operated according to Selux instructions. Fixture suitable for ambient temperatures from -35 C (-31 F) up to 40 C (104 F). For details and exclusions, see Selux Terms and Condition of Sale. Listings and Ratings: Tested to IESNA LM and LM-80 test standards at 25 C ambient temperature. In a continuing effort to offer the best product possible, we reserve the right to change, without notice, specifications or materials that in our opinion will not alter the

2 Motion Sensor The Selux outdoor rated sensor incorporates Passive Infrared (PIR) technology for motion sensing and also includes and built in photocell. Designed to mount directly through a 1/2 KO in a single gang faceplate on pole/column, the SBO utilizes 100% Digital Passive Infrared (PIR) technology that is tuned for walking size while preventing false tripping from the environment. Series Optics Mounting Height Hand Hole Orientation Program Color Photocell Feature Voltage MS Motion Sensor 1 270º coverage - Single Sensor XX Specify Height in incrememnts of 1ft (8ft min-30ft max D0 D1 D3 D5 0V=0% 1V=10% 3V=30% 5V=50% Goes from dim level to full bright upon motion WH White BK Black BZ Bronze Y N Yes No UNV " " (305mm) Generic Pole Drawing For Example Only Nominal Pole Height NOMINAL POLE HEIGHT NOTE: Motion sensor comes programmed at 30% dimmed level with a 5 min. delay as default. All programming required after shipping by others. SENSOR ANGULAR ORIENTATION FROM HAND HOLE 0Ā IN 90Ā INCREMENTS CLOCKWISE AROUND POLE (TYPE 00,09,18,27) SENSOR ANGULAR ORIENTATION FROM HAND HOLE 0Ā IN 90Ā INCREMENTS CLOCKWISE AROUND POLE (TYPE 00,09,18,27) 90Ā (09) 90Ā (09) HAND HOLD LOCATION 0Ā (00) 180Ā (18) HAND HOLD LOCATION 0Ā (00) 180Ā (18) 270Ā (27) 270Ā (27) RRSL (ss-v1.4)

3 Ritorno Round Asymmetrical LED Motion Sensor Features Features 100% Digital PIR Detection, excellent RF Immunity 270 coverage pattern Up to 30ft mounting IP66 Rated for outdoor applications Additional 10KvA surge protection included No minimum load requirements Made for LED light source Interchangeable hot and load wires - impossible to wire backwards Adjustable time delays, max/min dim levels and ramp rates Programming button accessible without opening sensor or removing gaskets No field calibration or sensitivity adjustments required Non-volatile setting memory Convenient test mode 5 year warranty Title 24 compliant Default dim level=30% Generic Pole Drawing For Example Only Wiring Diagram TO LEDS RED SUPPRESSOR RED CONNECT TO SENSOR LINE RRSL (ss-v1.4)

4 Photometry RRSL 55W LED Catalog #RRSL-1-L55-30 Report # S R1-1 l Maximum candela of 483 at 25 from vertical l IES classification: Type VS l 2289 Delivered Lumens l 42 Lumens per Watt l Based on 12 mounting height l BUG Rating B1-U3-G DOWNLOAD IES FILE: RRSL 55W LED Catalog #RRSL-1-L55-40 Report # S R1-1 l Maximum candela of at 25 from vertical l IES classification: Type VS l 2424 Delivered Lumens l 44 Lumens per Watt l Based on 12 mounting height l BUG Rating B1-U3-G DOWNLOAD IES FILE: RRSL (ss-v1.4)

5 Mounting Single Wall Mount 35 3 /4" (908mm) 6 1 /2" (165mm) 35 3 /4" (908mm) 36 5 /8" (931mm) 41 3 /4" (1061mm) /16" (735mm) 8 1 /2" (216mm) 14'-2 7 /8" (4.34M) Ø7" (178mm) Tapped 3/8-16 hole for ground connector Gasket Mounting hardware and anchorage designed and supplied and installed by others Mounting Plate Fixture Arm Cover 12' (3.66m) Set screws (2 places) Scale: 3/8" = 1' Ø5" (127mm) 18" (457mm) Cast aluminum handhole reinforcement frame with a full circumference weld and a 3" x 5" (76 x 127mm) flush fitting aluminum door. Attached with (2) stainless steel countersunk screws. Wall Mounting Plate Detail 6 1 /2" (165mm) 8 1 /2" (216mm) 7 3 /4" (197mm) Effective Projected Area of Single Luminaire = 1.7 ft 2 (0.157m 2 ) Weight of Luminaire = 60.0 lbs (27.3kg) Pole and luminaire engineered to withstand 120mph wind (+1.3 gust) as per AASHTO standards. See next page for Reverse Taper Pole EPA information. Mounted with (4x) 1/4-20 fasteners by others 5 3 /4" (146mm) RRSL (ss-v1.4)

6 Bolt Circle Use caution when setting anchor bolts. Bolts must be vertically straight and centered on dimensions shown. Ø8 5 /8" (219mm) Bolt Circle Anchor Bolt Detail 3 /4 " x 17" Galvanized Anchor Bolts Galvanized Heavy Hex Nut 9 1 /4" (235mm) Ø4 11 /16" (119mm) Conduit Opening 3 1 /4" (82.5mm) Galvanized Flat Washers Hand Hole Location Note: Adequate drainage must be provided in concrete foundation. 1 /2" (13mm) for leveling Galvanized Heavy Hex Leveling Nut Concrete footing designed and supplied by others BC3 Standard Base Cover Die-cast aluminum, two-piece field installable base cover. Ø 5" (127mm) Ø12 7 /16" (316mm) 4 1 /2" (116mm) Alternate Mounting Detail Height Options GFCI Receptacle (REC) - GFCI duplex receptacle with cast base welded to pole and gasketed, provided with weather-proof, self-closing cover; located 36" (915mm) from base of pole, inline with handhole. Receptacle is intended only for portable tools or other portable equipment to be connected to outlet only when attended by operating personnel /16" (71mm) 13 /16" (21mm) 2 13 /16" (71mm) Ritorno Reverse Taper Pole (5" to 7") EPA values calculated as per AASHTO LTS4 2001, to include fixture. Consult factory for heights other than 12'. Pole Windspeed Height ' ' ' ' All Poles are constructed per AASHTO standards for structural supports for highway signs, luminaires and traffic signals as published in 1975, amended and adopted in 1985 and A consideration of field conditions such as (but not limited to) wind zone, height, vibration must be given by the designer/specifier for the appropriate application. Performance of poles is dependent upon proper support/attachment of pole to adequate foundation design. Selux does not design or offer recommendations for foundations. EPA values assume that the bottom of the pole is at grade level. Call Selux (1-800-SELUXCS) if there are any questions, or for any assistance in determining suitability with appropriate fixtures. RRSL (ss-v1.4)

7 Option Details Hi-Lo Switching - Wiring Diagram LINE (POWER) 120V (ON/OFF) NEUTRAL (SHARED) GROUND DRIVER LIGHT ENGINE LINE (HI/LO) 120V ON = LO / OFF = HI HI/LO RELAY Dimming 0-10V - Wiring Diagram LINE (POWER) 120V (ON/OFF) NEUTRAL (SHARED) GROUND DRIVER LIGHT ENGINE 0-10 V ORG (-) RED (+) RRSL (ss-v1.4)