A-dec 570L Dental Light on a Non-DCS System INSTALLATION GUIDE

Transcription

1 A-dec 570L Dental Light on a Non-DCS System INSTALLATION GUIDE Non-DCS LED Dental Light Rev B

2 Choose an Installation Guide The manual used to install the light depends on whether the system has a Data Communication System (DCS). Use the following table to determine which installation guide to use per system. To Replace This Light Model Number Date of Manufacture Use This Installation Guide A-dec 37 December 008 until July 00 Note. Flexarms on these systems are not compatible with the LED light. To install a flexarm that is compatible with the LED light, order p/n A-dec 570L Dental Light on a DCS System. A-dec 37 A-dec 37 All models after June 00. A-dec 570L Dental Light on a DCS System. A-dec 57 A-dec 57 All models A-dec 570L Dental Light on a DCS System. A-dec 6300 mounted on a wall, cabinet, ceiling, or track March 004 until the present May 993 until March 004 Prior to 993 A-dec 570L Dental Light on a DCS System. A-dec 570L Dental Light on a Non-DCS System. These systems are not compatible with the LED light. A-dec 6300 Post Mount May 993 until present Prior to May 993 A-dec 570L Dental Light on a Non-DCS System. These systems are not compatible with the LED light. A-dec 6300 Radius All models A-dec 570L Dental Light on a Non-DCS System. A-dec 6300 Unit Mount All models A-dec 570L Dental Light on a Non-DCS System. A-dec Simulator All models For instructions for how to install an A-dec 570L on an A-dec simulator, contact A-dec customer service Rev B

3 Before You Begin. Turn off the power to the system before you begin these procedures. DANGER Failure to turn off the power before you begin this procedure can lead to electrical shock. WARNING Failure to turn off the power before you begin this procedure can lead to product damage and result in serious injury or death. CAUTION Circuit boards are sensitive to static electricity. Electrostatic Discharge (ESD) precautions are required when touching a circuit board or making connections to or from the circuit board. Circuit boards should be installed only by an electrician or qualified service person. CAUTION When removing or replacing covers, take care not to damage any wiring. Verify that the covers are secure after replacing them Rev B 3

4 Uninstall the Light Head Place the Flexarm Block Move the light head to its lowest position. Insert the pointed tab (on the notched end of the block) into the flexarm. 3 Insert the shorter tab into the light post Rev B

5 6A 5 VAC 3A 50 VAC ON ON ON A-dec 570L Dental Light on a Non-DCS System Installation Guide Remove the Light Head See the section for instructions on disconnecting the light cable for the system s configuration. Light Head Housing Covers with Three Screws on this page Light Head Housing Covers with Two Screws on page 8 Light Head Housing Covers with Three Screws Recommended Tools 5/64" and 5/3" hex keys Diagonal cutters Pliers Task. Remove this side of the switch housing cover. The other side is connected to a strain relief Rev B 5

6 6A 6A 5 5 VAC VAC 3A VAC VAC ON ON ON ON ON A-dec 570L Dental Light on a Non-DCS System Installation Guide Task. Remove the strain relief. Task 3. A-dec Ceiling Mount, Shown Cut off the white wire crimps next to the crimps. Cut the wires connecting the switch next to the switch Rev B

7 Task 4. Hold the pin. Remove the top screw. Task 5. Fixed Stop Remove the pin. Remove the head and brass bushing. Brass Bushing NOTE Make sure the fixed stop stays installed in the light head knuckle. It will be used with the LED light Rev B 7

8 Light Head Housing Covers with Two Screws Recommended Tools 5/64", /8", and 5/3" hex keys Diagonal cutters Task. Remove the switch housing cover. 6A 5 VAC 3A 50 VAC ON ON ON Rev B

9 6A 5 5 VAC VAC 3A VAC VAC ON ON ON ON ON ON A-dec 570L Dental Light on a Non-DCS System Installation Guide Task. Remove the strain relief. Task 3. A-dec Wall Mount, Shown Cut off the wire crimps next to the crimps. Cut the wires connecting the switch next to the switch Rev B 9

10 Task 4. Fixed Stop Remove the pin. Remove the head and brass bushing. Brass Bushing NOTE Make sure the fixed stop stays installed in the light head knuckle. It will be used with the LED light Rev B

11 Install the Light Head Attach the Light Head Recommended Tools Diagonal cutters 5/64" and 7/64" hex keys Task. For A-dec Post Mount, 6300 Unit Mount, and 6300 Radius Mount lights, remove the flexarm block. The block stays in place for all other configurations. Cut the wires at 3" (75 mm) from the knuckle. CAUTION Wires must be 3" (75 mm) in length to prevent damage to the light. 3" (75 mm) 3 Strip 3/8" (0 mm) off of all wires. WARNING All wires must be stripped to make proper connections and ensure wire nuts stay secure. 3/8" (0 mm) Rev B

12 Task. Apply Lubriplate to the knuckle. 3 4 Slide the cap above the knuckle. Verify the fixed stop is installed. Slide the white pivot bearing over the knuckle. Make sure the slot is not over the fixed stop. Slot Task 3. Rotation Stop Actual Size Keep the slot clear. Insert the rotation stop with its concave side towards the knuckle. Slide the rotation stop in the groove until it does not block the slot Rev B

13 Task 4. Remove the two screws securing the indicator cover. Slide the cover away from the housing to release the keyhole from the post. Task 5. Unplug the indicator cover wire Rev B 3

14 Task 6. Align the grooves in the light head with the posts on the pivot bearing and slide the light onto the knuckle. Post Rev B

15 Task 7. Insert the locking nut with its loop pointed to the right so that its grooves line up with the posts on the pivot bearing. Task 8. Turn the locking nut a /4 turn until the loop is over the hole for the screw. Secure the locking nut with a washer and screw Rev B 5

16 Task 9. Align the grooves in the brass pressure plate with the posts on the pivot bearing, then slide the plate onto the bearing. Task 0. Align the threads on the friction adjustment collar with the internal thread start. Screw in the friction adjustment until the head moves smoothly and holds its position. CAUTION When starting to install the friction adjustment, carefully align its threads to avoid cross threading. If the flexarm block is still installed, remove it Rev B

17 Task. Use a 5/64" hex key to start the two screws for the top cap. Once both screws are started, securely tighten them. Connect the Light Head Recommended Tool Voltage meter Task. Connect the black jumper wire (from the kit) to the 0 V terminal. Connect the violet jumper wire (from the kit) to the 4 V terminal Rev B 7

18 Task. Turn on the system. Use an AC voltage meter to determine the wire that measures the largest difference in voltage compared to the black or black/white wire (depending on the system). Also make sure the wire delivers at least 5 VAC. NOTE The number and color of wires will vary depending on the system. 3 Turn off the system. Black/White Blue Green Violet Task 3. Attach the black or black/white wire to the WAGO connector with the black wire. Attach the wire with the largest difference in voltage to the WAGO connector with the violet wire. While this wire is connected to the 4 V terminal, it is acceptable if it does not deliver a full 4 volts. The input operating range of the 4 V terminal is 5 VAC to 8 VAC. Black/White Violet Blue Green NOTE Do not install the indicator cover after making the connections. You will install the cover after adjusting the rotation tension. 3 Cap the remaining wires Rev B

19 Test the Light Task. Plug in the indicator cover wire Rev B 9

20 Task.. Turn on the system.. Turn on the light. 3. Press the buttons to test the light in each mode. 4. For each mode, verify that the correct light on the indicator cover is illuminated. 5. If it doesn t work properly, check the wire connections. 4 3 Cure-Safe High Medium Low Rev B

21 Adjust the Light Adjust the Horizontal and Diagonal Rotation Tension Recommended Tool 7/64" hex key Task. To adjust horizontal tension, rotate the friction adjustment. Clockwise increases the tension. To adjust diagonal tension, turn the setscrew. Clockwise increases the tension. Task. Slide the indicator cover so the keyhole fits around the post; then use the two screws to secure the cover Rev B

22 Adjust the Vertical Tension Recommended Tool 7/64" hex key To adjust the tension, turn the screw. Clockwise increases the tension Rev B

23 Adjust the Dental Light Flexarm Counterbalance Recommended Tools Phillips head screwdriver 5/64" hex key /" combination wrench. If the flexarm cover is in place, remove it.. Adjust the nut on the end of the spring. If the dental light drifts up, turn the nut counterclockwise. If the dental light drifts down, turn the nut clockwise. 3. Set the cover back onto the flexarm (but do not reattach it yet). Check for drift. 4. Repeat steps and 3 until drift is eliminated. NOTE An optional travel stop limit kit (p/n ) can be installed to limit the upward and downward motion of the flexarm Rev B 3

24 Regulatory Information Regulatory information mandated by agency requirements is provided in the Regulatory Information, Specifications, and Warranty document (p/n ), which is available in the Document Library at A-dec Headquarters 60 Crestview Drive Newberg, OR 973 USA Tel: Within USA/Canada Tel: Outside USA/Canada Fax: / A-dec Inc. makes no warranty of any kind with regard to the content in this document including, but not limited to, the implied warranties of merchantability and fitness for a particular purpose. ÍvÈ.Ç#RÈ.00ÅÎ Rev B Copyright 04 A-dec Inc. All rights reserved. IGgrphpor