Air Slide Table/Long Stroke Type

Transcription

1 ir Slide Table/ong Stroke Type Series ø6, ø8, ø1 RoHS MX long stroke type of series air slide table with integrated liner guide. D- -X

2 Use of linear guide provides rigid, The slide table comes with a built-in Rigid, compact, and lightweight idth Height Magnetically coupled rodless cylinder Compact design with higher allowable moment compared to /MX8 Height idth -0 7 MX /MX 0.8 times 0.9 times eight g times llowable moment N m Pitch, Yaw Roll times times Slide table is built with rigid and lightweight profile. Height Values for 0 stroke idth eight g Positioning pin hole Improved mounting repeatability of the workpiece and body <ottom view of body> Rubber stopper Positioning pin holes djuster options Metal stopper 6 pplication Example

3 compact, and lightweight design. magnetically coupled rodless cylinder. ong stroke Max. stroke 00 Series variations ore Stroke djuster options size () Rubber stopper Shock absorber Metal stopper Function options Piping concentrated on one side of the switch rail uto switch mounting Three types of auto switches can be mounted. Solid state auto switch: M9 type Reed auto switch: 9 type -color indicator solid state auto switch: M9 type MX Flexible Piping different piping directions are available: Horizontal piping, axial piping, and centralized piping Horizontal piping xial piping xial piping Stroke adjuster The stroke adjuster does not protrude from the mounting surface of the workpiece mounting surface, allowing high flexibility in workpiece mounting. orkpiece mounting surface Stroke adjuster Changing the mounting position of the switch rail, which also used as an air passage can change the direction of the centralized piping. Centralized piping Switch rail Switch rail Centralized piping Series djustment bolt Compact air slide table that comes with linear guide with built-in cylinder. ock plate Using lock plates to securely lock the adjustment bolt with minimal force. Series Stroke () Rubber stopper Stroke adjusters Metal stopper Shock absorber uto switch 7 D- -X

4 Series Selection 1 The following are the steps for selection of the series best suited to your application, Conditions and Calculation Flow for Selection Operating Conditions m: oad mass (kg) Mounting Orientation: V : Speed (/s) ccuracy: P : Operating pressure (MPa) Tentative Selection of Cylinder ore size: ø6, ø8, ø1 Stopper: Metal Rubber Examine load mass and kinetic energy NG Select larger cylinder size. Change stopper types. MX OK Consideration of load factor [Σα] 1 NG Select larger cylinder size. OK Examine auto switch mounting (Type) selected 9 D- -X

5 Series Selection Selection Step Formula/Data Selection Example 1 Operating Conditions Enumerate the operating conditions considering the mounting position and workpiece configuration. to be used Type of cushion Mounting orientation verage operating speed Va (/s) oad mass (kg) Overhang n () Cylinder: -0 Cushion: Rubber stopper Mounting: Horizontal wall mounting verage operating speed Va = 00 [/s] oad mass: = 0. [kg] = 0 = 0 + oad Mass Find the collision speed V (/S) Confirm that the load mass (kg) does not exceed the value in the graph. oad Factor -1 oad Factor of Static Moment Find the static moment M (N m). Find the allowable static moment Ma (N m). Find the load factor α1 of the static moment. - oad Factor of Dynamic Moment Find the dynamic moment Me (N m). Find the allowable dynamic moment Mea (N m). Find the load factor α of the dynamic moment. - Sum of the oad Factors 60 Use is possible if the sum of the load factors does not exceed 1. V = 1. Va Correction factor (Reference value) V = 1. x 00 = 0 Graph (1) Confirm that V = 0 and = 0. do not exceed the values in Graph (1). M = x 9.8 (n + n)/00 Corrected value of moment center position distance n: Table (1) Pitch, Yaw moment: Graph () Roll moment: Graph () α1 = M/Ma Me = 1/ e x 9.8 (n + n)/00 Mass equivalent to impact e = δ V δ: umper coefficient Rubber stopper screw: /0 : 1/0 Metal stopper screw: 16/0 Corrected value of moment center position distance n: Table (1) Pitch, yaw moment: Graph () α = Me/Mea α1 + α < 1 pplicable because it does not exceed the value in Graph (1). Examine Mr. Mr = 0. x 9.8 (0 + 1.)/00 = 0.1 = 1. Obtain Mar = 1 from Va = 00 in Graph (). α1 = 0.1/1 = kg Mar N m 0. 0 V /s Examine Mep. Mep = 1/ x.6 x 9.8 x (0+1.)/00 = 0.61 e = /0 x 0. x 0 =.6 = 1. Obtain Meap =. from V = 0 in Graph (). α = 0.61/. = 0.1. Meap N m 0 Examine Mey. V /s Mey = 1/ x.6 x 9.8 x (0+19)/00 = 0.76 e =.6 = 19 Obtain Meay =. from V = 0 in Graph (). α' = 0.76/. = Meay N m 1 00 Va /s 0 V /s α1 + α + α' = pplicable because = 0. < 1

6 Selection Series Fig. (1) Overhang: n (), Correction Value of Moment Center Position Distance: n () Fig. () llowable Static oad: F(N) Pitch moment Yaw moment Roll moment F F Mp 1 1 Static moment Dynamic moment Note) Static moment: Moment generated by gravity Dynamic moment: Moment generated by impact when colliding with stopper Table () Maximum llowable Moment: Mmax (N m) Pitch/Yaw moment: Mpmax/Mymax Roll moment: Mrmax n (n = 1 to ) n (n = 1 to ) Mp e Graph () llowable static moment Ma N m llowable dynamic moment Mea N m Mep Correction Value of Moment Center Position Distance: n () Corrected value of moment center position distance (Refer to Figure.) M (Mp, My, Mr) Ma (Map, May, Mar) Me (Mep, Mey) Mea (Meap, Meay) Mmax (Mpmax, Mymax, Mrmax) 1 19 My My e llowable Moment Pitch Moment: Map, Meap Yaw Moment: May, Meay Note) Use the average operating speed when calculating static moment. Use the collision speed when calculating dynamic moment. Table (1) verage operating speed Va /s 00 Collision speed V /s Mey 1 Definition Corrected value of moment center position distance Overhang Static moment (pitch, yaw, roll) llowable static moment (pitch, yaw, roll) Dynamic moment (pitch, yaw) llowable dynamic moment (pitch, yaw) Max. allowable moment (pitch, yaw, roll) Graph () Mr Mr llowable Moment Roll Moment: Mar Max. allowable load weight The above value represents the maximum value of allowable moment. For the maximum allowable moment for each piston speed, please refer to Graph () and (). llowable static moment Ma N m verage operating speed Va /s Table () Max. llowable oad Mass: max (kg) The above value represents the maximum value for each allowable load mass. For the maximum allowable load mass for each piston speed, please refer to Graph (1). Unit N m N m N m N m N m Graph (1) oad Mass: Collision speed V /s oad mass kg Collision speed V /s oad mass kg oad mass kg Table () llowable Static oad: F (N) The above value represents the applicable load at the position where the moment does not work at the time of stop. Factors such as impact, etc. are not in consideration with the value. F V Va a max α Collision speed V /s Rubber stopper screw Metal stopper screw Rubber stopper screw Metal stopper screw Metal stopper screw llowable static load Definition llowable static load Collision speed verage operating speed oad mass Equivalent mass for impact Max. allowable load mass oad factor Rubber stopper screw Unit N /s /s kg kg kg 61 MX D- -X

7 ir Slide Table ong Stroke Type Series ø6, ø8, ø1 RoHS How to Order 6 0 M9 Mode to Order For details, refer to page 6. ore size/standard stroke () 6 0, 0,, , 0,, 00, 0, , 0,, 00, 0, 00, 0, 00 djuster option Nil Rubber stopper C Metal stopper Only for Number of auto switches Nil pcs. S 1 pc. n "n" pcs. uto switch type Nil ithout auto switch (uilt-in magnet) One side centralized piping, switch rail Nil One side centralized piping, with switch rail N ithout one side centralized piping, without switch rail The auto switch cannot be mounted on the one side centralized piping type without switch rail (N). pplicable uto Switches/Refer to pages 1119 to 1 for further information on auto switches. Type Solid state auto switch Diagnostic indication (-color indicator) ater resistant (-color indicator) -wire (NPN) -wire (PNP) -wire -wire (NPN) Groet Yes -wire (PNP) -wire -wire (NPN) -wire (PNP) -wire -wire Yes (Equiv. to NPN) Groet -wire None V V, 1 V 1 V V, 1 V 1 V V, 1 V uto switch model Perpendicular M9NV M9PV M9V M9NV M9PV M9V M9NV 1 M9PV 1 M9V 1 In-line M9N M9P M9 M9N M9P M9 M9N 1 M9P 1 M9 1 ead wire length (m) IC circuit IC circuit IC circuit 1 V V 96V 96 IC circuit 0 V 9V 9 Relay, V 1 V 0 V or less 90V 90 IC circuit PC 1 ater resistant type auto switches can be mounted on the above models, but in such case SMC cannot guarantee water resistance. 1 m type lead wire is only applicable to D-9. ead wire length symbols: 0. m Nil (Example) M9N Solid state auto switches marked with are produced upon receipt of order. 1 m M (Example) M9NM m (Example) M9N m Z (Example) M9NZ Refer to page 69 for applicable auto switches in addition to those listed above. For details on auto switches with a pre-wired connector, refer to pages 119 and 119. uto switches are shipped together (not assembled). Reed auto switch Special function Electrical entry Indicator light iring (Output) oad voltage DC C 0. (Nil) 1 (M) () (Z) Pre-wired connector pplicable load Relay, PC 6

8 ir Slide Table ong Stroke Type Series Specifications ore size () Port size Fluid ction Operating pressure Proof pressure mbient and fluid temperature Operating speed range (verage operating speed) Note 1) Rubber Cushion ubrication Stroke adjuster Stroke adjustment range uto switch Rubber stopper Metal stopper Theoretical Output 6 8 M x 0.8 ir Double acting (type) 0. to 0. MPa 0.8 MPa to 60 C 0 to 00 /s Note ) Metal stopper: 0 to 00 /s 1 bumper Note ) (option, not available on, ) None (with metal stopper) Non-lube (equipment), unlubricated Standard One side 0 to One side 0 to 1 One side 0 to Reed auto switches (-wire, -wire) Solid state auto switches (-wire, -wire) -color indicator solid state auto switches (-wire, -wire) +1 Stroke length tolerance 0 Note 1) verage operating speed: Speed that the stroke is divided by a period of time from starting the operation to reaching the end. Note ) hen the smooth operation is required in a low speed range of 80 /s or less, contact SMC. Note ) The shock absorber service life is different from that of the cylinder depending on operating conditions. Refer to the Specific Product Precautions for the replacement period. (N) MX X7 X9 X11 X1 X9 X X eight Made to Order: Individual Specifications (Refer to pages 70 and 71 for details.) Specifications PTFE grease Grease for food processing machines djusting bolt, long specification (djustment range: 1 ) djusting bolt, long specification (djustment range: ) Fluororubber seal nti-corrosive guide unit EPDM seal Cylinder bore () Standard Stroke Piston area ( ) Standard stroke 0, 0,, 00 0, 0,, 00, 0, 00 0, 0,, 00, 0, 00, 0, 00 Operating pressure (MPa) () Magnetic Holding Force (N) Magnetic holding force (g) One side centralized piping, with switch rail Stroke () One side centralized piping, without switch rail Stroke () dditional weight of option 1 Moisture Control Tube IDK Series hen operating an actuator with a small diameter and a short stroke at a high frequency, the dew condensation (water droplet) may occur inside the piping depending on the conditions. Simply connecting the moisture control tube to the actuator will prevent dew condensation from occurring. For details, refer to the IDK series in the est Pneumatics No D- -X

9 Series Table Deflection (Reference Values) The graphs below show the table displacement when the static moment load is applied to the table. The graphs do not show the loadable mass. Refer to the Selection for the loadable mass. Table deflection due to pitch moment load Displacement at when load is applied F F Table deflection due to yaw moment load Displacement at when load is applied F F Table deflection due to roll moment load Displacement at when load is applied F F dimension 0 0 dimension 0 0 dimension 0 0 Pitch moment oad N Table deflection Yaw moment oad N Table deflection Roll moment Table deflection oad N 6

10 ir Slide Table ong Stroke Type Series y w q #0 r #6 # #!9 # @ MX e!8 Metal stopper Detail drawing of part Component Parts No Description Rail Guide block End plate ody Tube Cover Scraper Shaft Piston ear ring ear ring Spacer Magnet Magnet Yoke Yoke Return guide End cap Stud Material Stainless steel Stainless steel luminum alloy luminum alloy Stainless steel Resin Stainless steel, NR Stainless steel rass Resin Resin rass Steel Steel Resin Resin Stainless steel Note Heat treatment, electroless nickel plated Heat treatment, electroless nickel plated Hard anodized Hard anodized Electroless nickel plated Electroless nickel plated Nickel plated Nickel plated Electroless nickel plated Electroless nickel plated Heat treatment No Description Stopper screw External magnet fix plate Cylinder scraper ock plate djustment bolt Steel ball Piston seal O-ring O-ring djustment bumper Plug Switch rail Stud Gasket Magnet Magnet holder O-ring Material Note Stainless steel Heat treatment Stainless steel NR Stainless steel Steel Zinc chromated Rubber stopper Stainless steel Metal stopper High carbon chrome bearing steel NR NR NR Polyurethane Rubber stopper rass Electroless nickel plated luminum alloy Hard anodized rass Electroless nickel plated NR Nickel plated Steel Electroless nickel plated NR Replacement Parts ore size () Kit no. 6 -PS 8 -PS 1 -PS Contents set of two each Replacement Parts: Grease Pack Grease pack part no. GR-S-0 (g) GR-S-00 (0g) D- -X 6

11 Series Dimensions JH J + Stroke Piping port x M x 0.8 Same in case of the type of centralized ( piping on one side without switch rail ) PH Piping port x M x 0.8 (Plug: M-P) PR 1 idth across flats M (lock plate fixing bolt) M (Stroke adjuster) F x M thread depth MM ør R FH RH x M thread depth MM Piping port x M x 0.8 (Plug: M P) PR PH D 8. HR 0. P H D U idth across flats M (lock plate fixing bolt) R Q () 1. () () øt H Section TH (Head height of mounting bolt) øt Detail of part U Note) Since the rail and guide block are made of a magnetic substance, it could become magnetized if touched by a magnet, etc. This could cause auto switch malfunction. D -Mounting reference planes PR PR max18 PH PH E P F P Z + Stroke F M (Stroke adjuster) P H RH R ør Q (n 1) x Q Q Type of centralized piping on one side without switch rail Type of shock absorber (Only for ) F 0 FH F F 0 0 H 1. 6 H HR J JH M M x 0. M x 0.7 M x 0.8 MM 6 M M x 0.8 (idth across flats.) M6 x 1 (idth across flats ) M8 x 1 (idth across flats ) M. P PH P 9 1 PR Q Q R RH (depth ) (depth ) (depth ) (depth ) (depth ) (depth ) R T.9.. T TH D E. R 0 Z Stroke n Q

12 ir Slide Table ong Stroke Type Series Dimensions of djusting olt/rubber Stopper M pplicable size X11-67-X X11-87-X X11-17-X1 Stroke adjustment range M M 0.8 M6 1 M8 1 MX How to Order djusting olt/rubber Stopper 1 7 X11 pplicable bore size ø6 ø8 ø1 djustment range Nil -X11 1 -X1 For dimensions, refer to the figure above. 67 D- -X

13 Series Dimensions of djusting olt/metal Stopper M pplicable size X11-68-X X11-88-X X11-18-X1 Stroke adjustment range M M 0.8 M6 1 M8 1 How to Order djusting olt/metal Stopper 1 8 X11 pplicable bore size ø6 ø8 ø1 djustment range Nil -X11 1 -X1 For dimensions, refer to the figure above. 68

14 Series uto Switch Mounting uto Switch Proper Mounting Position (Detection at Stroke End) Reed uto Switch D-90(V), D-9(V), D-96(V) () Mounting uto switch operating range Solid State uto Switch D-M9(V), D-M9N(V), D-M9P(V) () Mounting uto switch operating range ead wire entries outside ead wire entries inside MX -Color Indicator Solid State uto Switch D-M9(V), D-M9N(V), D-M9P, D-M9(V) () Mounting uto switch operating range ead wire entries parallel djust the auto switch after confirming the operating conditions in the actual setting. uto Switch Mounting uto Switch Mounting Tool hen tightening the auto switch mounting screw (included with auto switch), use a watchmaker s screwdriver with a handle diameter of about to 6. Tightening Torque Tightening Torque of uto Switch Mounting Screw (N m) uto switch model Tightening torque D-9(V) 0. to 0.0 D-M9(V) D-M9(V) 0.0 to 0.1 D-M9(V) uto switch uto switch mounting screw (included with auto switch) atchmaker s screwdriver Other than the applicable auto switches listed in How to Order, the following auto switches can be mounted. Normally closed (NC = b contact) solid state auto switches (D-F9G/F9H types) and a solid state auto switch (D-F8) are also available. Refer to pages 116 and 117 for details. 69 D- -X

15 Series Made to Order: Individual Specifications 1 Please contact SMC for detailed dimensions, specifications and lead times. 1 PTFE Grease -X7 nti-corrosive Specifications for Guide Unit -X Standard model no. X7 Standard model no. X arning Precautions PTFE grease PTFE grease is used for all parts that grease is applied. Specifications Type PTFE grease ore size () 6, 8, 1 Dimensions other than the above is the same as the standard type. e aware that smoking cigarettes, etc. after your hands have come into contact with the grease used in this cylinder can create a gas that is hazardous to humans. Grease for Food Processing Machines -X9 nti-corrosive specifications for guide unit Martensitic stainless steel is used for the rail and guide block. Use this treatment if more effective anti-corrosive measures are necessary. nti-corrosive treatment is applied to the rail and guide block. Specifications Type nti-corrosive guide unit ore size () 6, 8, 1 Surface treatment Special anti-corrosive treatment () 1 Dimensions other than the above is the same as the standard type. The special anti-corrosive treatment turns rail and guide block black. EPDM Seal -X Standard model no. X9 Standard model no. X Grease for food processing machines Grease for food processing machines is used for all parts that grease is applied. Specifications Grease for Food Processing Machines Type (NSF-H1 certified)/luminum Complex Soap ase Grease ore size () 6, 8, 1 Dimensions other than the above is the same as the standard type. Do not use this cylinder in a food-related environment. Splash zone Can be mounted <Cannot be mounted> Food zone Food may directly contact with this cylinder, and is treated as food products. <Can be mounted> Splash zone Food may directly contact with this cylinder, but is not treated as food products. Non-food zone This cylinder do not directly contact food. Fluororubber Seal Food zone Cannot be mounted Food Container Non-food zone Can be mounted. -X9 EPDM seal Change the materials for the piston seal, cylinder scraper, O-rings and scrapers (rubber lined parts) to EPDM. Specifications Type EPDM seal ore size () 6, 8, 1 Seal material EPDM Grease PTFE grease Dimensions other than the above is the same as the standard type. arning Precautions e aware that smoking cigarettes, etc. after your hands have come into contact with the grease used in this cylinder can create a gas that is hazardous to humans. Standard model no. X9 Fluororubber seal Change the materials for the piston seal, cylinder scraper, O-rings and scrapers (rubber lined parts) to fluororubber. Specifications Type Fluororubber seal ore size () 6, 8, 1 Seal material Fluororubber Dimensions other than the above is the same as the standard type. 70

16 Series Made to Order: Individual Specifications Please contact SMC for detailed dimensions, specifications and lead times. 6 djustment olt, ong Specification (djustment range: 1 ) -X11 7 djustment olt, ong Specification (djustment range: ) -X1 Max. Standard model no. -X11 is not available for those with a shock absorber. The average adjusting stroke range was extended from to 1 with a long adjustment bolt. Dimensions X11 djustment bolt, long specification (djustment range: 1 ) Max. Max. Standard model no. Dimensions X1 djustment bolt, long specification (djustment range: ) -X1 is not available for those with a shock absorber. The average adjusting stroke range was extended from to with a long adjustment bolt. Max. MX Rubber Stopper Metal Stopper.... () () Rubber Stopper Metal Stopper.... () () D- 71 -X

17 Series Specific Product Precautions 1 e sure to read this before handling the products. Refer to back page 0 for Safety Instructions and pages to 1 for ctuator and uto Switch Precautions. 1. Use a load within a range that does not exceed the operating limit. Select models based on the maximum load weight and the allowable moment. Refer to model selection on pages 9 to 61 for detailed methods. If operated beyond the operating limit, the eccentric load applied to the guide section will be excessive. This can have an adverse effect on service life due to vibration in the guide unit and loss of accuracy, etc.. hen performing intermediate stops with an external stopper, employ measures to prevent lurching. If lurching occurs damage can result. hen making a stop with an external stopper to be followed by continued forward movement, first supply pressure to momentarily reverse the table, then retract the intermediate stopper, and finally apply pressure to the opposite port to operate the table again.. In vertical operation, it is not possible to stop the piston at an intermediate position using a closed center solenoid valve, etc. In vertical operation, it is not possible to stop the piston at an intermediate position using a closed center solenoid valve because it can cause dislocation of the magnet coupling. The only available option in such cases is use of an external stopper for an intermediate stop.. hen stopping the piston using a closed center solenoid valve in horizontal operation, do not allow the kinetic energy exceed the allowable kinetic energy. hen stopping the piston using a closed center solenoid valve in horizontal operation, do not allow the kinetic energy of the load to exceed the values shown below. If the allowable value is exceeded, it can cause dislocation of the magnet coupling. llowable kinetic energy for intermediate stop (J) Selection. Do not operate in such a way that excessive external forces or impact forces are applied to the product. This can cause damage. 6. e careful in an application which requires precision in the middle of a stroke. If straightness is required in the middle of a stroke, fix the entire rail mounting surface on the base. Mounting 1. Do not scratch or gouge the mounting surfaces of the body, table and end plate. This can cause loss of parallelism in the mounting surfaces, vibration in the guide unit and increased operating resistance, etc.. Do not scratch or gouge the transfer surfaces of the rail and guide. This can cause vibration and increased operating resistance, etc.. Do not apply strong impacts or excessive moment when mounting workpieces. pplication of external forces greater than the allowable moment can cause vibration in the guide unit and increased operating resistance, etc.. Ensure that the parallelism of the mounting surface is 0.0 or less. Poor parallelism of the workpiece mounted on the body, the base, and other parts can cause vibration of the guide unit and increased operating resistance, etc. Mounting. For connection to a load that has an external support or guide mechanism, select an appropriate connection method and perform careful alignment. 6. Keep away objects which can be influenced by magnets. magnet is built inside the body or, in case of a type with auto switch, on the side of the guide lock. Please keep away magnetic disks, cards or tapes. Otherwise, the data can be deleted. 7. Do not attach magnets to the rail and guide block. Since the body and table (guide block) are made of a magnetic substance, it could become magnetized if touched by a magnet, etc. This could cause auto switch malfunction. 7

18 Series Specific Product Precautions e sure to read this before handling the products. Refer to back page 0 for Safety Instructions and pages to 1 for ctuator and uto Switch Precautions. 8. hen mounting the body, use screws of an appropriate length and do not exceed the maximum tightening torque. Tightening with a torque above the limit could cause malfunction. hereas tightening insufficiently could result in misalignment or dropping. M. x 0. M x 0. M x 0.7 Using through holes olt M x 0. M x 0.7 M x 0.8 Max. tightening torque N m Top mounting type olt M x 0. M x 0.7 M x 0.8 Side mounting type olt Max. tightening torque N m Max. tightening torque N m Rail thickness () 1. Max. screw-in depth () Max. screw-in depth () 9. e careful not to bruise the outer surface of the cylinder tube. If can damage the scraper and wear ring and result in malfunction. Mounting. Make sure that the magnet coupling is in position when operating. In case it is displaced, please return it to the right position by pushing the external mover by hand (or pushing the piston mover with air pressure). 11. In vertical operation, be careful about dislocation of the magnet coupling. Note that the mover may drop off due to dislocation of the magnet coupling if pressure or load beyond the specifi-cation is applied. 1. The positioning holes on the top surface of the guide block and those on the bottom of the rail are not aligned. These holes are used when re-mounting the same product after having removed it for maintenance. Operating Environment 1. Do not use in environments where there is direct exposure to liquids such as cutting oil. Operation in environments where the body is exposed to cutting oil, coolant or oil mist can cause vibration, increased operating resistance and air leakage, etc.. Do not use in environments where there is direct exposure to foreign matter such as dust, dirt, chips and spatter. This can cause vibration, increased operating resistance and air leakage, etc. Do not use the product in the following conditions.. Provide shade in locations exposed to direct sunlight.. lock off sources of heat located near by. hen there are heat sources in the surrounding area, radiated heat may cause the product's temperature to rise and exceed the operating temperature range. lock off the heat with a cover, etc.. Do not use in locations where vibration or impact occurs. Do not use the product in such an environment as is can result in damage or malfunction. 6. e careful about the corrosion resistance of the linear guide. e careful the rail and guide block use martensitic stainless steel, which is inferior to austenitic stainless steel in terms of corrosion resistance. Rust may result especially in an environment that allows water drops from condensation to stay on the surface. Handling of djuster Options Stroke adjuster 1. Do not replace the special adjusting bolt with other bolts. This may cause looseness and damage due to impact forces, etc.. Use the tightening torque in the table below for the lock nut. Insufficient torque will cause a decrease in the positioning accuracy. Piston rod Operating Environment Do not damage pplicable size Do not turn bottom screw Service ife and Replacement Period of Shock bsorber 1. llowable operating cycle under the specifications set in this catalog is shown below. 1. million cycles R08 Note) Specified service life (suitable replacement period) is the value at room temperature (0 to C). The period may vary depending on the temperature and other conditions. In some cases the absorber may need to be replaced before the allowable operating cycle above. model R MX D- -X

19 Series Specific Product Precautions e sure to read this before handling the products. Refer to back page 0 for Safety Instructions and pages to 1 for ctuator and uto Switch Precautions. Stroke djustment 1. djustment method oosen the lock plate fixing bolts (or shock absorbers) and rotate the adjustment bolt (or shock absorber) to adjust the stroke. Then tighten the lock plate fixing bolts evenly to secure the adjustment bolt (or shock absorber). e careful not to tighten the lock plate adjusting bolts too firmly. Tightening torque of lock plate fixing bolt 0.1 N m 0. N m 0. N m The piping is concentrated on the left side at the time of shipment. To switch to the right side piping, follow the steps below. 1. oosen the studs to remove the switch rail. Stud How to Change Concentrated Piping t the time of shipment eft Concentrated piping Right Stretch rail mounting position fter change Concentrated piping Switch rail Stud Stretch rail mounting position ock plate ock plate Fixing bolt djustment bolt Note) The lock plate may bend slightly due to tightening of the lock plate fixing bolts but it will not affect the adjustment bolt or shock absorber that has been secured.. Change the position of the O-ring shown in the figure. Port ctuation Direction Right eft. djustment range djust the stroke within the range where the stopper or shock absorber works effectively. s a guideline, keep the stroke within the range where the dimension in the figure below is larger than the value in the table. If the stroke exceeds this range, the guide lock will bump into the end plate, affecting the life time.. Rubber stopper screw Metal stopper screw O-Ring. Fasten the stud onto the tap at the right side of the end plate and secure the switch rail. Switch rail Mounting tap Stud fastening: fter a temporary tightening, tighten an additional 1/ turn. Disassembly and Maintenance arning e careful the magnets have a large absorption force. Please pay enough attention when the external mover and piston mover are removed from the cylinder tube for maintenance, etc. ecause the magnet mounted on each mover has a large adsorption force. Please refer to the disassembly instructions when disassembling the product. 1. e careful if the external mover is removed in the normal condition, it will directly absorb the piston mover. hen removing the external mover or piston mover, first force the magnet coupling to go off the position to disable the holding power and then remove them separately. If they are removed in the normal condition, the magnets will directly absorb each other and will not go apart.. Never disassemble the magnet constructions (piston mover and external mover). If can cause a drop of the holding power or malfunction. 7