All hardware is mounted in steel enclosure (see dimensions below) and includes a HT28100 transformer and a single power supply board.

Transcription

1 Honeywell 12 Clintonville Road Northford, CT Overview HPV3L HPV58L HPV516L HPV3LCB HPV58LCB HPV516LCB Power upplies/distribution nits PN 536:B2 6/18/13 CN Product Installation Document These switching power supplies/distribution units convert 115 V input into 6 V, 12 V, or A or.0 A of continuous supply current and distribute it using individually fused or PTC outputs. These general-purpose power supplies have a wide range of applications for access control, security and CCTV systems that require additional power. or convenient installation, they come completely assembled with a steel enclosure, transformer, and connecting hardware. 2 Product Contents All hardware is mounted in steel enclosure (see dimensions below) and includes a HT28100 transformer and a single power supply board. Product Power upply Board Distribution Board Quantity HPV3L HP3 HPD 1 HPV3LCB HP3 HPDCB 1 HPV58L HP5 HPD8 1 HPV58LCB HP5 HPD8CB 1 HPV516L HP5 HPD8 2 HPV516LCB HP5 HPD8CB 2 3 eatures Designed for quick installation. Power /O switch. iltered and electronically regulated output. Individually protected fused or PTC outputs. Diagnostic LDs for quick troubleshooting. Transformer has built-in thermal protection. Vented enclosure with hinged door and five convenient knockouts. line cord and terminal block fuse protection included. nit maintains camera synchronization. pecifications L-listed to L-20 Commercial CCTV quipment. Maximum temperature range: 32 to 120 (0 C to 9 C); indoor use only. nclosure dimensions: 10" H x 11.5" W x.875" D (cm: 25. H x W x D). Input: 115V, 60 Hz, 1.0 A. Output voltage: switch selectable 6/12/2 V. Output current: see Voltage Output Table/ Maximum Total Output Current on page 2.

2 .1 Voltage Output Table/ Maximum Total Output Current Main output voltage is switch selectable. Note the maximum output current at each output voltage. witch selector is located on HP3 and HP5 power supply board. ee igure 1 below Product 6 V 12 V 2 V HPV3L 2.5 A 2.5 A 2.5 A HPV3LCB 2.5 A 2.5 A 2.5 A HPV58L.0 A.0 A 2.5 A HPV58LCB.0 A.0 A 2.5 A HPV516L.0 A.0 A 2.5 A HPV516LCB.0 A.0 A 2.5 A LD (red) TB1 + LD (red) TB LD (green) LD (green) HP3 HP5 W 1.1 W 1.2 Configuration (hown in 12 V position) Output W 1 (lide right to turn on) W 2 (lide right to turn on) 2 V Off On 12 V Off Off 6 V On Off igure 1 Voltage election Diagrams 2 HPV3L(CB), HPV58L(CB), HPV516L(CB) Product Installation Document P/N 536:B2 6/18/13

3 .2 LD Diagnostic Table HP3/HP5 Power (Green LD) HP3/HP5 Power (Red LD).3 use Replacement Table HPD/HPD8 Output Power (Green LDs) tatus (All) Normal operation. O O O (All) Loss of / main fuse blown. O O (All) No output. Overload present. O (One or more) Blown fuse(s) on HPD/8.! CATI:RIK O QIPMNT DAMAG! TO R TH RIK O IR, RPL LY WITH O TH AM TYP AND RATING. use Mains Terminal Block HPD Main econdary use (9) HPD- Outputs (1-) HPD-8 Outputs (1-8) Rating 2.0 A, 250 V, 5 x 20mm cartridge. 5.0 A, 32 V, standard automotive (tan). 3.0 A, 32 V, standard automotive (violet) 3.0 A, 32 V, standard automotive (violet) 5 Installation Instructions 1. npack product. Do not discard packaging material until installation is complete. 2. Pre-drill holes where enclosure is to be mounted. Choose a vertical surface strong enough to support the full weight of the assembly. elect a mounting location in an area without excessive moisture; for indoor installation only. 3. ecure enclosure to the desired location using the appropriate sized fasteners.. Configure the power supply using DIP switches to select output voltage required (refer to igure 1). 5. Disconnect power to the branch circuit to which the product will be connected. 6. Place W1 on the distribution board/boards (HPD/HPD8) in the off position. 7. Connect incoming power (115 V, 60 Hz): Hot (black) to terminal marked L. Neutral (white) to terminal marked N. Ground to terminal marked G. 8. se the knockout in bottom of cabinet for 115 V wiring. Route the 115 V wiring at least 1/" from (low voltage) wiring. 9. Keep a 1/" (0.635 cm) separation between power-limited wiring and non-power-limited wiring. se separate knockouts for power limited wiring. 10. Connect CCTV cameras (or other external loads) to appropriate terminals: Connect circuit #1 to terminals marked 1+ and. Connect circuit #2 to terminals marked 2+ and. Continue to connect the remaining circuits, carefully observing polarity. Terminals marked with are of the same polarity. 11. Power the branch circuit and slide W1 to the position. All LDs should illuminate. 12. To avoid potential damage, verify that out put voltage and load current does not exceed output limitations. 13. pon completion of wiring, secure cabinet door with screws supplied, to prevent access by unauthorized person. HPV3L(CB), HPV58L(CB), HPV516L(CB) Product Installation Document P/N 536:B2 6/18/13 3

4 HPV3L OTPT KNOCKOT OR LOW-VOLTAG ILD WIRING HPD INPT POWR TRMINAL (115 V, 60 Hz) HP3 TRANORMR NTRAL 5371bd.wmf HPV3LCB OTPT KNOCKOT OR LOW-VOLTAG ILD WIRING HPDCB A MINIMM O 1/ HALL B MAINTAIND BTWN TH ILD WIRING AND TH INTRNAL TORY WIRING. INPT POWR TRMINAL (115 V, 60 Hz) HP3 TRANORMR NTRAL 5385bd.wmf HPV3L(CB), HPV58L(CB), HPV516L(CB) Product Installation Document P/N 536:B2 6/18/13

5 HPV58L OTPT KNOCKOT OR LOW-VOLTAG ILD WIRING CKT #8 CKT #7 CKT #6 CKT #5 A MINIMM O 1/ HALL B MAINTAIND BTWN TH ILD WIRING AND TH INTRNAL TORY WIRING. HPD8 INPT POWR TRMINAL (115 V, 60 Hz) HP5 TRANORMR NTRAL 537bd.wmf HPV58LCB OTPT KNOCKOT OR LOW-VOLTAG ILD WIRING CKT # 8 CKT #7 CKT # 6 CKT #5 HPD8CB INPT POWR TRMINAL (115 V, 60 Hz) HP5 TRANORMR NTRAL 5388bd.wmf HPV3L(CB), HPV58L(CB), HPV516L(CB) Product Installation Document P/N 536:B2 6/18/13 5

6 HPV516L 5373bd.wmf HPV516LCB 5387bd.wmf! WARNING:TO R TH RIK O IR OR LCTRIC HOCK, DO NOT XPO THI APPLIANC TO RAIN OR MOITR. RIK O LCTRICAL HOCK AND/OR QIPMNT DAMAG, DICNCT POWR BOR RVICING THI APPLIANC. OR CTINO PROTCTI AGAINT HAZARD, RPL WITH LY XT TYP AND RATING. MAINTAIN A 1/" O PARATI BTWN TH MAIN AND ALL LOW VOLTAG WIRING. A RADILY CIBL WITCHD CIRCIT BRAKR MT B AVAILABL TO DICNCT MAIN POWR A RQIRD. THI NIT CTAIN NO R-RVICABL PART, INTALLATI AND RVICING HOLD LY B MAD BY QALIID PRLL. INTALL IN CORDANC WITH WITH ALL LOCAL RGLATI AND NATIAL LCTRIC COD. or additional information: Visit our website at Contact Technical upport at (877) HPP-POWR -mail us at hpp_techserv@honeywell.com 6 HPV3L(CB), HPV58L(CB), HPV516L(CB) Product Installation Document P/N 536:B2 6/18/13