5SB (11/01/12)

Transcription

1 5SB (11/01/12)

2 Introduction Read this manual carefully. It will instruct you on how to operate and service your machine safely and correctly. Failure to do so could result in personal injury and or equipment damage. This SAFETY ALERT symbol is intended to warn you of some potential hazard. You should look for this symbol on your equipment and throughout this manual. If you see this symbol you should carefully read the warning that is printed beside or under the symbol and follow it! Failure to do so can result in serious bodily injury or death. WARRANTY: Warranty coverage is provided by John Deere according to the terms of the Agricultural/Commercial & Consumer Equipment Warranty Statement. Carefully read the warranty statement on the back of your original purchase order for details on coverage and limitations of this warranty. This warranty does not cover the following: Cleaning, transporting, mailing and service call charges. Normal wear items such as bearings, chains, sprockets, points, etc. Depreciation or damage caused by normal wear, accidents, improper maintenance improper protection or improper use of the machine. For complete Warranty information see inside back cover of this manual. Record your implement model and serial number in the space provide below. Your dealer will need this information to give you prompt, efficient service. Model Number: Serial Number: Date Purchased: 2

3 Dealer Checklist To the Dealer: Inspect the machine thoroughly after assembly to assure it is functioning properly before delivering it to the customer. The following checklist is a reminder of points to cover. Check off each item as it is found satisfactory or after proper adjustment is made. Predelivery Checklist 1. All hardware properly tightened. 2. Lubrication of all grease fittings. 3. All chains properly aligned and tight. 4. All decals properly located and legible. 5. All guards in place and secure. 6. Overall condition and appearance (touch up any scratches, clean/polish) 7. Test run, check for any vibrations, chain popping, or unusual noise. 8. Seed cups open and close properly. 9. Seed cup gates all in the same postion. 10. Transmission sprocket engages and disengages the hopper drive properly. 11. Machine is equipped with operator s manual. Date Set Up Signature 3

4 Delivery Review the operator s manual with the customer. Explain the following: 1. John Deere Equipment Warranty 2. Safe operation and service 3. Correct installation and maintenance 4. Daily and periodic lubrication, cleaning and all other maintenance 5. Correct lubricants 6. Daily and periodic inspections 7. Troubleshooting 8. Machine storage 9. John Deere Equipment parts and service 10. Fill in model and serial numbers in the provide space on the introductory page of this manual 11. Remove and file this page 12. Give customer this operator s manual and encourage them to read it carefully and operating and safety procedures. follow all Date Delivered Model Number Serial Number Signature (dealer) Signature (customer) 4

5 Table of Contents Section I Introduction and Safety Introduction Dealer Check List 3 Delivery 4 Safety Precautions 5 Safety Decals 6 Section II Owner / Operating Instructions Specifications 8 Determining correct tractor ballast 9 Pre-Operations 10 Operations 10 Lubrication and Maintenance 11 Calibration and Adjustments & Rates 12 Seed Rate Adjustment Procedures Seed Rate Charts Troubleshooting 19 Torque chart 20 Section III Parts Breakdown Parts Breakdown Weights and AFC

6 Safety Precautions 1. Read this manual carefully before beginning operations. 2. Allow only properly trained personnel to operate this machine. 3. Read and adhere to all safety precautions posted on this machine and written in this manual. Review safety decal illustrations on page 7 and machine locations on pages Be sure that all guards are in place and properly secured; and all warning decals are in place and legible. 5. Be certain that all hardware is properly tightened. 6. Always use a tractor of sufficient size and weight to properly lift and carry machine safely and securely. 7. Be certain that no persons are standing near the machine before starting tractor engine. 8. Never allow passengers on tractor or machine. 9. Never attempt to service any part of machine with tractor engine running. 10. Always shut off engine; lock brakes and lower machine before inspecting, servicing or making any adjustment of any kind. 11. Never climb on machine when filling seed hoppers or servicing. 12. Never put hands, arms, feet or legs under machine when it is raised off ground with tractor lift. If machine needs to be raised to perform work; always securely block it up only as high as necessary to perform the services needed. 6

7 Safety Decals Qty 1 Falling Off Can Result in Being Run Over Warning Decal 2 x Additional safety equipment: Qty 2 2 x 9 Red Reflectors Qty 1 2 x 9 Yellow Reflector (CS1384 only) SMV sign Qty 1 - Crushing and Pinching Hazard Warning Decal 2.87 x 7 Qty 3 - Do Not Step Warning Decal Qty 1 - Chemical Warning Decal (Fert. Box only) 4 x

8 Specifications SPECIFICATIONS CS1360 CS1384 HITCH CAT 1 & 2 CAT 1 & 2 HORSE POWER (MIN) 30 HP 50 HP WORKING WIDTH 60" 84" OVERALL WIDTH 73" 98" OVERALL LENGTH 67" 76" OVERALL HEIGHT 48" 54" WEIGHT LARGE SEED BOX CAPACITY SMALL SEEDBOX CAPACITY FRONT SPIKE ROLLER REAR SPIKE ROLLER REAR CULTIPACKER ROLLER ROLLER SPIKES 1480 lbs. 3-1/2 Bu. (4.4 Cu.Ft) 1-1/2 Bu (1.87 Cu. Ft) 15.75" O.D. w/ 72 spikes 15.75" OD w/ 114 spikes Fiber Reinforced Nylon Rings AR-500 Steel 2090 LBS 8-1/4 Bu. (10.3 Cu.Ft) 2-1/8 Bu (2.64 Cu. Ft) 19.75" O.D.w/ 150 spikes 19.75" O.D. w/ 144 spikes Fiber Reinforced Nylon Rings AR-500 Steel SPIKE ROLLER DRIVE RATIO 15:22 15:18 SEEDBOX DRIVE RATIO 15:28 Standard 17:28 standard 8

9 9

10 Pre-Operating Instructions Make sure machine is properly hitched to a tractor of sufficient size & weight to properly handle and safely lift machine. Check that all hardware is properly tightened. Check that machine has been properly lubricated. Check that all chains are properly aligned and tightened. Check all seed/fertilizer boxes to make certain that no foreign objects (tools, bolts, etc) were left inside that might damage seed cups. Check that all seed cup gates are in same position. Operating Instructions The Conservation Seeder is a multi-task landscape machine. It can be used for primary seeding, over seeding, applying fertilizer or lime, aerating and dethatching. If conditions are such that multiple passes are needed before application of seed; you can disengage seed box by pulling out spring loaded pin in transmission sprocket assembly found behind large guard on left side of machine. Rotate the pin 90 degrees and release. To re-engage seed box drive assembly, reverse this procedure. When the sprocket rotates enough to align the holes, the internal spring will cause the pin to engage the inside sprocket. 10

11 Operating Instructions, cont. The depth of the second spike roller can be controlled by the length of the turnbuckles that connect the torque bar to the cultipacker roller. Lengthen the turnbuckles to raise the rear or driven spike roller or shorten the turnbuckle if you want the driven spike roller to operate deeper. The rear cultipacker roller is spring loaded in order to provide good ground contact in uneven terrain and to prevent itself and the driven spike roller from cavitating in low spots. The tickler tines are to improve seed to soil contact and should not be positioned aggressive enough to carry trash or residue in an over seeding situation. The top link on the tractor hitch should be properly adjusted to carry the machine level in an operating position. During operation the tractor lift must be fully lowered to allow the machine to follow the contour of the ground. The machine is totally ground driven, so proceed with a speed that is most comfortable and safe for existing conditions. Be sure to stop forward motion before lifting machine off ground. This practice will stop rollers from free spinning and therefore eliminate the unwanted application of when turning around. Never operate the machine in reverse, serious damage will occur. Lubrication & Maintenance 1 Hour Check all fasteners and hardware including set screws in sprockets and bearing collars and retighten as necessary. 8 Hours Grease bearings and inspect chains for tightness. 25 Hours Remove guard cover on right hand side of machine and inspect chain; lubricate using multipurpose lithium base grease. As needed: Remove any crop residue, grasses, weeds, or debris wrapped around shafts near bearings. This can cause bearings to overheat and lead to premature failure. Always: Protect machine from weather. Never leave fertilizer in hopper. Do not leave seed in hopper for more than 24 hours. Remove all fertilizer and seeds and thoroughly clean hoppers and lubricate all drive chains before storage. 11

12 Calibration Adjustments and Rates The tables and rate charts in this manual are for guidelines only. They are designed to be an aid as a starting point. You must do your own calibration; as many factors cause rates to change. Variations in seed/granular size, density, moisture, seed treatment, and the amount of machine overlap will affect the final application rate. Also slippage of front spike roller will cause variations. For instance, in loose soil, such as disced or harrowed, the front roller will slip possibly up to 20%; while in over seeding into established vegetation, you will likely have very little slippage. The most accurate way to set application rates is to drive a predetermined distance and actually catch the seeds dispensed. To do this, remove at least one drop hose and tie a plastic bag onto bottom of seed cup. Then weigh the seeds in the bag and multiply by the number of cups on your machine. Refer to the following example to properly calibrate your machine. Distance traveled (in feet) x Width of machine (in feet) / 43,560 = acres For example: You collect 1.25 oz of seed from 1 cup after driving a 1/100 of an acre (87 ft. for model Greenscape 600 machine or 62ft. for model 840) 60 (5 ) machine = 1/100 acres 84 (7 ) machine = 1/100 acres 1.25 oz (seed caught from 1 cup) x 8 (total number of cups on 60 hopper) 1.25 oz (seed caught from 1 cup) x 10 (total number of cups on 84 hopper) 1/100 acre) 10 oz (seed applied to x oz (seed applied to 1 acre) / 16 (16oz = 1 lb) 12.5 oz (seed applied to 1/100 acre) x oz (seed applied to 1 acre) / 16 (16oz = 1 lb) 62.5 lbs per acre lbs per acre Caution: Never allow a rider on machine for any reason including collecting seeds for calibration purposes. Always affix a container or plastic bag to seed cup spouts or hoses to catch samples. Never place hands in hopper or near agitator shaft while seed shaft is rotating. 12

13 Large Grass Seed Hopper Seed Rate Adjustment Procedure To increase the seed rate, turn the knob on the right end of the hopper clockwise, and lock the jam nuts on the threaded shaft to assure seeding accuracy. Refer to the indicator reading on the square seed shaft and find the corresponding number on the calibration chart 2 to assure your new rate. Reverse this procedure to decrease rate. Remember to rotate the seed shaft while adjusting to prevent damage to cups especially if seeds are in hopper. Note: When seed cups are fully closed, the indicator should be on 0 (on the rule). This can be adjusted by simply adjusting the pointer as needed. Fully open would be 1-3/4. Small (Legume) Seed Hopper The seed rate adjustment for the optional small hopper is located on the left side of the hopper behind the panel standing at the rear of the machine. To increase the seed rate, turn the knob on the left side of the hopper clockwise and then lock the jam nut. Refer to the indicator reading on the square seed shaft (right side) and find the corresponding number on the calibration chart in Chart 3 to assure your new rate. Reverse this procedure to decrease rate. Refer to Chart 3 or 4 on page of this manual or the rate chart located inside the hopper lid for the corresponding seeding rate. Note: When seed cups are fully closed, the indicator should be on 0 (on the rule). Fully open would be 1-1/8. Native Grass Seed Hopper The optional front native grass seed box has a special agitator shaft for fluffy or chaffy seeds; such as some wildflowers and native grasses. Move the chains onto the sprocket combinations to achieve the desired rate. 13

14 Also, the transmission sprockets for the large boxes are equipped with disengaging pins. This allows the operator to disengage either the front box, center box or, if equipped, the combination of both center and rear small boxes. To disengage, pull the spring pin out, rotate 90 degrees to lock. To re-engage, rotate pin 90 degrees to release. Each of the seed boxes can be set at different planting rates and used simultaneously if needed. If not using a large seed box, it should be disengaged to prevent unnecessary wear and tear on components. Caution: When adjusting seeder shaft on a loaded box, rotate the shaft slowly to prevent cup damage. Caution: Never allow a rider on machine for any reason including collecting seeds for calibration purposes. Always affix a container or plastic bag to seed cup spouts or hoses to catch samples. Never place hands in hopper or near agitator shaft while seed shaft is rotating. 14

15 Calibration Chart Large Seed Hopper Chart 1 Distribution rate in lbs per acre ** lbs of Seed collected ** Total material collected from all cups in pounds Distance Traveled in Feet Note: Measure actual shaft movement from closed position for a more accurate seeder opening setting. 15

16 Calibration Chart Large Seed Hopper Chart 2 Caution: When adjusting seeder shaft on a loaded box, rotate the shaft slowly to prevent cup damage. Note: Measure actual shaft movement from closed position for a more accurate seeder opening setting. Caution: Never allow a rider on machine for any reason including collecting seeds for calibration purposes. Always affix a container or plastic bag to seed cup spouts or hoses to catch samples. Never place hands in hopper or near agitator shaft while seed shaft is rotating. 16

17 Calibration Chart Precision Small (Legume) Hopper Chart 3 & 4 17

18 Calibration Chart Native Grass Hopper Chart 5 Calibration Chart - Native Grass Hopper - Chart 5 Sprocket Positions Sprocket Drive Lower Sprocket Driver Upper Seed Variety lbs per acre Little Blue Stem Virginia Wild Rye Big Blue Stem Native River Oats Indian Grass Native Side Oats Gamma Caution: Never allow a rider on machine for any reason including collecting seeds for calibration purposes. Always affix a container or plastic bag to seed cup spouts or hoses to catch samples. Never place hands in hopper or near agitator shaft while seed shaft is rotating. 18

19 Troubleshooting Caution: Turn off tractor engine, lock parking brake and remove key before servicing machine Problem Cause Solution Loose chains Tighten idlers Machine makes a clicking or popping noise Chain stretched or damaged Sprocket tooth damaged or broken Replace chain Replace sprocket Crop residue is dragging or rolling up Tickler tines set too aggressive Loosen U-bolts and or rotate forward to raise tips off the ground Seed flow continuing when machine is lifted up Rollers free spinning Stop forward movement before raising machine 19

20 Torque chart General Torques Bolt Size Grade 5 Torque In. Lbs In. Lbs In. Lbs In. Lbs In. Lbs In. Lbs In. Lbs In. Lbs. 1/ In. Lbs. 1/ In. Lbs. 5/ Ft. Lbs. 5/ Ft. Lbs. 3/ Ft. Lbs. 3/ Ft. Lbs. 7/ Ft. Lbs. 7/ Ft. Lbs. 1/ Ft. Lbs. 1/ Ft. Lbs. 9/ Ft. Lbs. 9/ Ft. Lbs. 5/ Ft. Lbs. 5/ Ft. Lbs. 3/ Ft. Lbs. 3/ Ft. Lbs. 7/ Ft. Lbs. 7/ Ft. Lbs Ft. Lbs Ft. Lbs. ** Torque listed for plated or lubricated bolts ** Torque listed for plated or lubricated bolts ** To insure the use of correct grade hardware, order hardware from a John Deere Frontier dealer. 20

21 Section III - Parts Breakdown CS1360 Main Frame CS1360 Large Grass Box CS1360 Precision Legume Seed Box CS1360 Stainless Steel Fertilizer Hopper CS1360 Native Grass Seed Box CS1384 Main Frame CS1384 Large Grass Box CS1384 Precision Legume Seed Box CS1384 Stainless Steel Fertilizer Hopper CS1384 Native Grass Seed Box Corrugated Roller Assy and Rear Scraper Tine Bar Assembly Seed Cups Decal Layout Light Kit

22 CS1360 Main Frame 22

23 CS1360 Main Frame ITEM PART # DESCRIPTION QTY 1 5SB MAIN FRAME WELDMENT 1 2 5SB CULTIPACKER ASSEMBLY NYLON 5' 1 3 5SB BOLT, HH 3/4-10X3 GR SB NUT, NYLOK 3/4-10 GR SB TORQUE ARM WELDMENT 1 6 5SB CHAIN GUARD WELDMENT 1 7 5SB FRONT ROLLER BEARING SPACER 1/2" 1 8 5SB FRONT SPIKE ROLLER 1 9 5SB PILLOW BLOCK BEARING NAP SB FRONT ROLLER BEARING SPACER 1/4" SB REAR SPIKE ROLLER SB BOLT, CARRIAGE 1/2-13X2 1/2 GR SB WASHER, LOCK 1/2" SB NUT, HEX 1/2-13 GR SB TINE BAR ASSEMBLY 5' SB TINE BAR U-BOLT SB NUT, FLANGE 3/8-16 GR SB SMALL SEED PAN WELDMENT SB BOLT, CARRIAGE 5/16-18X3/4" GR SB NUT, FLANGE 5/16-18 GR SB BOLT, CARRIAGE 3/8-16X3/4 GR SB SMALL HOPPER ASSEMBLY 5' SB LARGE HOPPER ASSEMBLY 5' SB PLATE LOWER HINGE GUARD SB CLIP LOWER CHAIN GUARD SB BOLT, CARRIAGE 3/8-16X1 1/4 GR SB CHAIN GUARD PANEL WELDMENT SB /8" PLASTIC WASHER SB BOLT, HH 3/8-16X1 GR SB NUT, NYLOK 3/8-16 GR SB SPROCKET 50BS15H (1 1/4" BORE) SB KEY, 1/4" X 1" SB GUIDE SHAFT SB IGUS BEARING MFI SB IGUS THRUST WASHER MTI SB SMALL SPROCKET WELDMENT SB LARGE SPROCKET WELDMENT SB THREADED LOCKING PIN SB SHAFT COLLAR 3/4" BORE SB IDLER SPROCKET 50BB15HX1/2" SB BOLT, CARRIAGE 1/2-13X2 GR SB WASHER, FLAT 5/8" SB WASHER, FLAT 1/2" SB SPROCKET 60BS22H (1 1/4" BORE) 1 23

24 CS1360 Main Frame 24

25 CS1360 Main Frame ITEM PART # DESCRIPTION QTY 45 5SB SPROCKET 60BS15H (1 1/4" BORE) SB IDLER ASSEMBLY DRIVE SB COVER LOWER CHAIN GUARD WELDMENT SB NUT, PREVAILING TORQUE 3/4-10 GR SB SPRING TENSIONER ROD WELDMENT SB BOLT, HH 1/4-20X3/4 GR SB WASHER, LOCK 1/4" SB IDLER TENSION SPRING SB HITCH PIN ASSEMBLY SB LYNCH PIN 7/16 X 1 3/ SB HOSE, SMALL HOPPER SB ADJUSTABLE REAR ARM SB TORQUE BAR SPRING LH SB TORQUE BAR SPRING RH SB BOLT, HH 3/4-10X3 1/4 GR SB BOLT, HH 3/4-10X3 1/2 GR SB ROLLER CHAIN # 60 H X 30 LINKS SB ROLLER CHAIN #50 X 40 LINKS SB ROLLER CHAIN # 50 X 31 LINKS SB ROLLER CHAIN # 40 X 37 LINKS SB SET SCREW 3/8-16X1/ SB TORQUE TUBE INNER WELDMENT SB WASHER, LOCK 3/4" SB BOLT, HH 3/4-10X2 GR SB SMV EMBLEM SB SMV OFFSET BRACKET SB SMV MOUNTING BRACKET SB BOLT, HH 5/16-18X3/4 GR SB NUT, HEX 5/16-18 GR SB SEED PAN WELDMENT LARGE 5' SB SMV MOUNTING STRAP 1 25

26 CS1360 Large Grass Seed Box 26

27 CS1360 Large Grass Seed Box ITEM PART NUMBER DESCRIPTION QTY 1 5SB LARGE HOPPER WITH LID ASSEMBLY 1 2 5SB GUARD MOUNTING CLIP 1 3 5SB BOLT, CARRIAGE 5/16-18X3/4" GR SB NUT, FLANGE 5/16-18 GR SB DRIVE SHAFT LARGE HOPPER 1 6 5SB DRIVE ASSEMBLY WELDMENT 1 7 5SB OUTBOARD BRACKET 1 8 5SB AGITATOR SHAFT WELDMENT 1 9 5SB HOLE TRIANGULAR BEARING FLANGE 52MSTR SB BEARING INSERT SB SB IDLER SPROCKET ASSEMBLY SB LARGE HOPPER SEED CUP ASSEMBLY SB FEED SHAFT ADJUSTER SB COLLAR FEED SHAFT SB BEARING INSERT SB SB HOLE BEARING FLANGE 47MSTZ SB POINTER FEED SHAFT SB MACHINE SCREW TRUSS HEAD PHILLIPS 10-24X5/8 GR SB NUT, FLANGE #10-24 GR SB MACHINE SCREW TRUSS HEAD PHILLIPS 1/4-20X5/8 GR SB NUT, FLANGE 1/4-20 GR SB NUT, JAM 3/4-10 GR SB ADJUSTMENT ROD WELDMENT 5' SB /8" PLASTIC WASHER SB ADJUSTMENT KNOB SB BOLT, HH 3/8-16X1 GR

28 CS1360 Precision Small (Legume) Seed Box 28

29 CS1360 Precision Small (Legume) Seed Box ITEM PART # DESCRIPTION QTY 1 5SB SMALL HOPPER BASE ASSEMBLY 1 2 5SB SMALL SEED CUP ASSEMBLY SB SMALL HOPPER LID WELDMENT 1 4 5SB UNIVERSAL LID MOUNTING PLATE 2 5 5SB SHOULDER BOLT, 5/ SB BOLT, CARRIAGE 5/16-18X3/4" GR SB BEARING INSERT SB SB HOLE BEARING FLANGE 47MSTZ SB SMALL HOPPER DRIVE SPROCKET WELDMENT SB NUT, FLANGE 5/16-18 GR SB COLLAR FEED SHAFT SMALL HOPPER SB MACHINE SCREW TRUSS HEAD PHILLIPS 10-24X5/8 GR SB NUT, FLANGE #10-24 GR SB DRIVESHAFT WELDMENT SMALL HOPPER SB THREADED ROD WITH SHOULDER SB RETAINER CLIP SB NUT, JAM 3/8-16 GR SB ADJUSTMENT KNOB SB NUT, NYLOK 5/16-18 GR SB SPACER, SMALL DECAL SCALE 1 29

30 CS1360 Stainless Steel Fertilizer Hopper 30

31 CS1360 Stainless Steel Fertilizer Hopper ITEM PART NUMBER DESCRIPTION QTY 1 5SB FERTILIZER LID WELDMENT 5' 1 2 5SB FERTILIZER HOPPER WELDMENT 5' 1 3 5SB LID MOUNTING PLATE STAINLESS 2 4 5SB FERTILIZER LID LOCK LOWER 1 5 5SB FERTILIZER LID LOCK UPPER 1 6 5SB SHOULDER BOLT, 5/ SB NUT, NYLOK 5/16-18 GR SB BOLT, CARRIAGE 5/16-18X3/4" GR SB NUT, FLANGE 5/16-18 GR SB BOLT, HH 1/4-20X3/ STAINLESS SB NUT, FLANGE 1/ STAINLESS SB STAINLESS AGITATOR SHAFT WELDMENT 5' SB FERTILIZER SEED CUP ASSY SB MACHINE SCREW TRUSS HEAD PHILLIPS 1/4-20X5/8 STAINLESS SB NUT, FLANGE 1/4-20 STAINLESS SB HOLE TRIANGULAR BEARING FLANGE 52MSTR SB BEARING INSERT SB SB DRIVE ASSEMBLY WELDMENT SB DRIVE SHAFT LARGE HOPPER SB BOLT, CARRIAGE 5/16-18X3/4" 18-8 STAINLESS SB NUT, FLANGE 5/ STAINLESS SB HOLE BEARING FLANGE 47MSTZ SB BEARING INSERT SB SB GUARD MOUNTING CLIP SB OUTBOARD BRACKET SB IDLER SPROCKET ASSEMBLY SB FEED SHAFT ADJUSTER SB NUT, JAM 3/4-10 GR SB COLLAR FEED SHAFT SB POINTER FEED SHAFT SB MACHINE SCREW TRUSS HEAD PHILLIPS 10-24X5/8 GR SB NUT, FLANGE #10-24 GR SB PLUG PLASTIC 11/32 HOLE SB DECAL, WARNING CHEMICAL SB ADJUSTMENT ROD WELDMENT 5' SB BOLT, HH 3/8-16X1 GR SB /8" PLASTIC WASHER SB ADJUSTMENT KNOB 1 31

32 CS1360 Native Grass Seed Box 32

33 CS1360 Native Grass Seed Box ITEM PART NUMBER DESCRIPTION QTY 1 5SB NATIVE GRASS HOPPER WELDMENT 1 2 5SB SPUR GEAR WELDMENT NATIVE GRASS 8 3 5SB NATIVE GRASS PICKER WHEEL SHAFT 1 4 5SB NATIVE GRASS AGITATOR SHAFT 1 5 5SB IGUS BEARING MFI SB SHAFT COLLAR 1" BORE 2 7 5SB SPROCKET 50BS17H 1 8 5SB AGITATOR WELDMENT NATIVE GRASS 4 9 5SB SHEET METAL SIDE FRONT SB SHEET METAL SIDE REAR SB KNURLED INSERT 1/ SB END CAP RH SB END CAP LH SB BOLT, HH 1/4-20X3/4 GR SB WASHER, LOCK 1/4" SB MACHINE SCREW TRUSS HEAD PHILLIPS 1/4-20X5/8 GR SB NUT, FLANGE 1/4-20 GR SB BOLT, HH 3/8-16X1 GR SB LARGE HOPPER LID ASSEMBLY SB UNIVERSAL LID MOUNTING PLATE SB LID MOUNTING PLATE SB LARGE HOPPER LID LOWER LOCK SB SHOULDER BOLT, 5/ SB NUT, HEX 5/16-18 GR SB WASHER, FLAT 1/4" SB NUT, HEX 1/4-20 GR SB KEY, 1/4" X 1" SB BOLT, CARRIAGE 5/16-18X3/4" GR SB NUT, FLANGE 5/16-18 GR SB DRIVE SPROCKET WELDMENT SB IDLER BRACKET WELDMENT NATIVE GRASS SB UHMW IDLER NATIVE GRASS SB /8" PLASTIC WASHER SB NUT, NYLOK 5/16-18 GR SB WASHER, FLAT 3/8" SB WASHER, LOCK 3/8" SB NUT, HEX 3/8-16 GR SB ROLLER CHAIN #40 X LINKS SB COVER PANEL WELDMENT NATIVE GRASS SB DECAL, CALIBRATION CHART NATIVE GRASS SB WINGED THRUMB SCREW 1/4-20X1/ SB SPRING, NATIVE GRASS IDLER SB COTTER PIN 1/16 X 1/ SB CLEVIS PIN 1/4X1-3/8 2 33

34 CS1384 Main Frame 34

35 CS1384 Main Frame ITEM PART NUMBER DESCRIPTION QTY 1 5SB ' MAIN FRAME WELDMENT 1 2 5SB PILLOW BLOCK BEARING NAPL-208D SB ' FRONT SPIKE ROLLER WELDMENT 1 4 5SB ' REAR SPIKE ROLLER WELDMENT 1 5 5SB ' TORQUE ARM WELDMENT 1 6 5SB ' TINE BAR ASSEMBLY 1 7 5SB TINE BAR U-BOLT 2 8 5SB NUT, FLANGE 3/8-16 GR SB BOLT, CARRIAGE 1/2-13X2 GR SB WASHER, LOCK 1/2" SB NUT, HEX 1/2-13 GR SB ' CULTIPACKER ASSEMBLY NYLON SB LARGE SEED PAN WELDMENT 7' SB SMALL HOPPER ASSEMBLY 7' SB LARGE HOPPER ASSEMBLY 7' SB NUT, NYLOK 3/4-10 GR SB BOLT, HH 3/4-10X3 GR SB BOLT, CARRIAGE 3/8-16X3/4 GR SB BOLT, CARRIAGE 5/16-18X3/4" GR SB NUT, FLANGE 5/16-18 GR SB GUIDE SHAFT SB SET SCREW 3/8-16X1/ SB IGUS THRUST WASHER MTI SB IGUS BEARING MFI SB TRANSMISSION SPROCKET WELDMENT LARGE 7' SB SMALL SPROCKET WELDMENT SB SHAFT COLLAR 3/4" BORE SB THREADED LOCKING PIN SB ADJUSTABLE REAR ARM SB BOLT, HH 3/4-10X3 1/2 GR SB TORQUE BAR SPRING LH SB TORQUE BAR SPRING RH SB PLUG PLASTIC 11/32 HOLE SB PLATE LOWER HINGE GUARD SB CLIP LOWER CHAIN GUARD SB BOLT, CARRIAGE 3/8-16X1 1/4 GR SB /8" PLASTIC WASHER SB TORQUE TUBE INNER WELDMENT 7' SB WASHER, LOCK 3/4" SB BOLT, HH 3/4-10X2 GR SB SMALL SEED PAN WELDMENT 7' SB WASHER, FLAT 5/8" SB IDLER SPROCKET 50BB15HX1/2" SB BOLT, CARRIAGE 1/2-13X1 1/2 GR

36 CS1384 Main Frame 36

37 CS1384 Main Frame ITEM PART NUMBER DESCRIPTION QTY 45 5SB HOSE SMALL HOPPER 7' SB SPROCKET 80BS15 X 1-1/ SB SPROCKET 80BS18 (1-1/2 BORE) SB SPROCKET, 50BS17 (1-1/2 BORE) SB CHAIN GUARD WELDMENT 7' SB CHAIN GUARD COVER PANEL WELDMENT 7' SB SIDE COVER PANEL WELDMENT 7' SB BOLT, HH 3/8-16X1 GR SB NUT, NYLOK 3/8-16 GR SB ROLLER CHAIN #50 X 100 LINKS (MAIN DRIVE) SB ROLLER CHAIN #50 X 53 LINKS (LARGE HOPPER) SB ROLLER CHAIN #40 X 89 LINKS (SMALL HOPPER) SB IDLER ASSEMBLY CHAIN DRIVE 7' SB IDLER TENSION SPRING SB IDLER TENSIONER ROD WELDMENT SB ROLLER CHAIN #80 X 61 LINKS (CHAIN GUARD SB BOLT, HH 5/16-18X3/4 GR SB NUT, HEX 5/16-18 GR SB SMV EMBLEM SB SMV OFFSET BRACKET SB SMV MOUNTING BRACKET SB SMV MOUNTING STRAP SB HITCH PIN ASSEMBLY SB LYNCH PIN 7/16 X 1 3/ SB WASHER, LOCK 5/16" 2 37

38 CS1384 Large Grass Seed Box 38

39 CS1384 Large Grass Seed Box ITEM PART NUMBER DESCRIPTION QTY 1 5SB LARGE HOPPER WELDMENT 7' 1 2 5SB UNIVERSAL LID MOUNTING PLATE 2 3 5SB LARGE HOPPER LID WELDMENT 7' 1 4 5SB LARGE HOPPER LID LOWER LOCK 1 5 5SB LID MOUNTING PLATE 1 6 5SB SHOULDER BOLT, 5/ SB NUT, NYLOK 5/16-18 GR SB BOLT, CARRIAGE 5/16-18X3/4" GR SB BOLT, HH 1/4-20X3/4 GR SB WASHER, FLAT 1/4" SB WASHER, LOCK 1/4" SB NUT, HEX 1/4-20 GR SB LARGE HOPPER SEED CUP ASSEMBLY SB MACHINE SCREW TRUSS HEAD PHILLIPS 1/4-20X5/8 GR SB NUT, FLANGE 1/4-20 GR SB IGUS BEARING MFI SB HOLE BEARING FLANGE 47MSTZ SB BEARING INSERT SB SB NUT, FLANGE 5/16-18 GR SB OUTBOARD BRACKET 7' SB DRIVE ASSEMBLY WELDMENT SB DRIVE SHAFT LARGE HOPPER 7' SB COLLAR FEED SHAFT SB FEED SHAFT ADJUSTER SB POINTER FEED SHAFT SB MACHINE SCREW TRUSS HEAD PHILLIPS 10-24X5/8 GR SB NUT, FLANGE #10-24 GR SB LARGE HOPPER AGITATOR SHAFT WELDMENT 7' SB SHAFT COLLAR 1" BORE SB IDLER SPROCKET ASSEMBLY SB GUARD MOUNTING CLIP SB NUT, JAM 3/4-10 GR SB AGITATOR WELDMENT SMALL 7' SB SET SCREW 3/8-16X1/ SB AGITATOR WELDMENT LARGE 7' SB ADJUSTMENT ROD WELDMENT 7' SB /8" PLASTIC WASHER SB ADJUSTMENT KNOB SB BOLT, HH 3/8-16X1 GR

40 CS1384 Precision Legume Seed Box 40

41 CS1384 Precision Small (Legume) Seed Box ITEM PART # DESCRIPTION QTY 1 5SB SMALL HOPPER WELDMENT 7' 1 2 5SB UNIVERSAL LID MOUNTING PLATE 2 3 5SB SMALL HOPPER LID WELDMENT 7' 1 4 5SB SHOULDER BOLT, 5/ SB NUT, NYLOK 5/16-18 GR SB BOLT, CARRIAGE 5/16-18X3/4" GR SB SMALL HOPPER DRIVE SPROCKET WELDMENT 1 8 5SB DRIVESHAFT WELDMENT SMALL HOPPER 7' 1 9 5SB THREADED ROD WITH SHOULDER SB RETAINER CLIP SB ADJUSTMENT KNOB SB SMALL SEED CUP ASSEMBLY SB COLLAR FEED SHAFT SMALL HOPPER SB MACHINE SCREW TRUSS HEAD PHILLIPS 10-24X5/8 GR SB NUT, FLANGE #10-24 GR SB IGUS CLIP BEARING MCI SB SHAFT COLLAR 3/4" BORE SB NUT, JAM 3/8-16 GR SB NUT, FLANGE 5/16-18 GR SB SPACER, SMALL DECAL SCALE 1 41

42 CS1384 Stainless Steel Fertilizer Hopper 42

43 CS1384 Stainless Steel Fertilizer Hopper ITEM PART NUMBER DESCRIPTION QTY 1 5SB FERTILIZER HOPPER WELDMENT 7' 1 2 5SB FERTILIZER LID WELDMENT 7' 1 3 5SB FERTILIZER LID LOCK LOWER 1 4 5SB FERTILIZER LID LOCK UPPER 1 5 5SB SHOULDER BOLT, 5/ SB NUT, NYLOK 5/16-18 GR SB BOLT, CARRIAGE 5/16-18X3/4" GR SB FERTILIZER SEED CUP ASSY SB IGUS BEARING MFI SB HOLE BEARING FLANGE 47MSTZ SB BEARING INSERT SB SB NUT, FLANGE 5/16-18 GR SB OUTBOARD BRACKET 7' SB DRIVE ASSEMBLY WELDMENT SB DRIVE SHAFT LARGE HOPPER 7' SB COLLAR FEED SHAFT SB FEED SHAFT ADJUSTER SB POINTER FEED SHAFT SB MACHINE SCREW TRUSS HEAD PHILLIPS 10-24X5/8 GR SB NUT, FLANGE #10-24 GR SB STAINLESS AGITATOR SHAFT WELDMENT 7' SB SHAFT COLLAR 1" BORE SB IDLER SPROCKET ASSEMBLY SB GUARD MOUNTING CLIP SB NUT, JAM 3/4-10 GR SB LID MOUNTING PLATE STAINLESS SB BOLT, HH 1/4-20X3/ STAINLESS SB NUT, FLANGE 1/ STAINLESS SB BOLT, CARRIAGE 5/16-18X3/4" 18-8 STAINLESS SB NUT, FLANGE 5/ STAINLESS SB MACHINE SCREW TRUSS HEAD PHILLIPS 1/4-20X5/8 STAINLESS SB NUT, FLANGE 1/4-20 STAINLESS SB STAINLESS AGITATOR WELDMENT SMALL 7' SB STAINLESS AGITATOR WELDMENT LARGE 7' SB PLUG PLASTIC 11/32 HOLE SB SET SCREW 3/8-16X1/ STAINLESS SB DECAL, WARNING CHEMICAL SB ADJUSTMENT ROD WELDMENT 7' SB BOLT, HH 3/8-16X1 GR SB /8" PLASTIC WASHER SB ADJUSTMENT KNOB 1 43

44 CS1384 Native Grass Seed Box 44

45 CS1384 Native Grass Seed Box ITEM PART NUMBER DESCRIPTION QTY 1 5SB NATIVE GRASS HOPPER WELDMENT 7' 1 2 5SB UNIVERSAL LID MOUNTING PLATE 2 3 5SB LARGE HOPPER LID WELDMENT 7' 1 4 5SB SHOULDER BOLT, 5/ SB NUT, NYLOK 5/16-18 GR SB BOLT, CARRIAGE 5/16-18X3/4" GR SB NUT, FLANGE 5/16-18 GR SB IGUS BEARING MFI SB SPUR GEAR WELDMENT NATIVE GRASS SB NATIVE GRASS DRIVESHAFT 7' SB SHAFT COLLAR 1" BORE SB SPROCKET 50BS17H SB NATIVE GRASS AGITATOR SHAFT 7' SB DRIVE SPROCKET WELDMENT SB REAR SHEETMETAL PANEL SB FRONT SHEETMETAL PANEL SB END CAP LH SB KNURLED INSERT 1/ SB END CAP RH SB BOLT, HH 1/4-20X3/4 GR SB WASHER, LOCK 1/4" SB MACHINE SCREW TRUSS HEAD PHILLIPS 1/4-20X5/8 GR SB NUT, FLANGE 1/4-20 GR SB AGITATOR WELDMENT NATIVE GRASS SB SCREW SQUARE HEAD 3/8-16X3/4 GR SB UHMW IDLER BLOCK SB BOLT, HH 3/8-16X3 1/2 GR SB NUT, HEX 3/8-16 GR SB WASHER, FLAT 3/8" SB WASHER, LOCK 3/8" SB IDLER BRACKET WELDMENT NATIVE GRASS SB /8" PLASTIC WASHER SB UHMW IDLER NATIVE GRASS SB ROLLER CHAIN #40 X 28 LINKS SB COVER PANEL WELDMENT NATIVE GRASS SB AGITATOR SHAFT HOLDER NATIVE GRASS SB DRIVE SHAFT HOLDER NATIVE GRASS SB DECAL, CALIBRATION CHART NATIVE GRASS SB WINGED THRUMB SCREW 1/4-20X1/ SB SPRING, NATIVE GRASS IDLER SB COTTER PIN 1/16 X 1/ SB CLEVIS PIN 1/4X1-3/ SB AGITATOR WELDMENT 7' N.GRASS CENTER 2 45

46 CS1360 & CS1384 Corrugated Roller Assembly & Optional Scraper 46

47 CS1360 & CS1384 Corrugated Roller Assembly & Optional Scraper ITEM PART # DESCRIPTION CS1360 CS SB ' CULTIPACKER FRAME WELDMENT 1-5SB ' CULTIPACKER FRAME WELDMENT SB ' CULTIPACKER ROLLER ASSEMBLY NYLON 5' 1-5SB ' CULTIPACKER ROLLER ASSEMBLY CAST IRON 5' 1-5SB ' CULTIPACKER ROLLER ASSEMBLY NYLON - 1 5SB ' CAST IRON CULTIPACKER ROLLER ASSEMBLY SB PILLOW BLOCK BEARING NAP SB ROLLER SCRAPER RH,PLASTIC RING 1 1 5SB ROLLER SCRAPER RH, CAST RING 1 5 5SB ROLLER SCRAPER LH, PLASTIC RING 1 1 5SB ROLLER SCRAPER LH, CAST RING 1 6 5SB U-BOLT CULTIPACKER SB NUT, FLANGE 3/8-16 GR SB BOLT, CARRIAGE 1/2-13X2 GR SB WASHER, LOCK 1/2" SB NUT, HEX 1/2-13 GR SB ROLLER SCRAPER CENTER NYLON - 1 5SB ROLLER SCRAPER CENTER CAST RING SB ' CULTIPACKER ROLLER WELDMENT - 1 5SB CULTIPACKER ROLLER WELDMENT SB DISC RETAINER TAB W/HOLE SB BOLT, HH 3/8-16X1 1/4 GR SB WASHER, LOCK 3/8" SB NUT, HEX 3/8-16 GR SB NYLON CULTIPACKER RING SB CAST IRON CULTIPACKER RING

48 CS1360 & CS1384 Tine Bar Assemby 48

49 CS1360 & CS1384 Tine Bar Assemby ITEM PART NUMBER DESCRIPTION CS1360 CS SB TINE BAR ( Model CS1360) 1 1 5SB TINE BAR ( Model CS384) SB COIL TINE SB TINE BAR SPACER SB TINE HOLD DOWN SB BOLT, HH 3/8-16X2 1/2 GR SB WASHER, LOCK 3/8" SB NUT, HEX 3/8-16 GR

50 CS1360 & CS1384 Seed Cups 50

51 CS1360 & CS1384 Seed Cups ITEM PART NUMBER DESCRIPTION QTY 1 5SB SEED CUP HOUSING (J.D.) AN SB SEED CUP SPACER(J.D.) M SB SEED CUP GEAR (J.D.) M SB FERTILIZER SEED CUP GEAR 1 ITEM PART NUMBER DESCRIPTION QTY 1 5SB PRECISION 3x SMALL SEED (LEGUME) CUP HOUSING 1 2 5SB PRECISION 3x SMALL SEED (LEGUME) CUP SPACER 1 3 5SB PRECISION 3x SMALL SEED (LEGUME) CUP GEAR 1 51

52 CS1360 & CS1384 Decal Layout 52

53 CS1360 & CS1384 Decal Layout ITEM PART # DESCRIPTION CS1360 CS SB DECAL, SCALE SMALL HOPPER SB DECAL, SCALE LARGE HOPPER SB YELLOW REFLECTIVE STRIP 2" X 9" SB STRIP, RED RETROREFLECTIVE 2" X 9" SB DECAL, CS SB DECAL, CS SB DECAL, FRONTIER EQUIPMENT 3.5X SB DECAL, WARNING FALLING OFF SB DECAL, WARNING CRUSHING SB DECAL, WARNING TO AVOID SB DECAL, DO NOT STEP SB DECAL, CALIBRATION CHART SB DECAL, CALIBRATION CHART SB DECAL, CALIBRATION CHART

54 CS1360 & CS1384 Light Kit 54

55 CS1360 & CS1384 Light Kit ITEM PART NUMBER DESCRIPTION QTY 1 5SB LIGHT MOUNTING BRACKET 2 2 5SB AG LIGHT RH 1 3 5SB BOLT, CARRIAGE 5/16-18X3/4" GR SB NUT, FLANGE 5/16-18 GR SB BOLT, HH 1/4-20X1 GR SB NUT, FLANGE 1/4-20 GR SB AG LIGHT LH 1 8 5SB COMPLETE WIRING HARNESS 1 55

56 Weights CS1360 Machine lbs Shipping lbs Base machine with 1 large grass seed box 1,355 1,430 Base machine with 1 large grass seed box + 1 small (legume) seed box 1,420 1,495 Base machine with 1 large grass seed box + 1 small (legume) seed box + 1 large stainless steel fertilizer box 1,567 1,642 Base machine with 1 large grass seed box + 1 small (legume) seed box + 1 large native grass seed box 1,627 1,702 Base machine with 2 large grass seed boxes + 1 small (legume) seed box 1,567 1,642 Small (legume) seed box only Large Grass Seed boxo only Stainless Steel box only Native Seed Box only Attachments for field Conversion (AFC's) Bundle Number Short Description Long Description Bundle Qty 5SBGSC003 SCRPPYWHLS CS1360 REAR PK SCRP POLYWHLS 1 5SBGSC006 SCRPCIWHLS CS1360 REAR PK SCRP CIWHLS 1 5SBGSC008 SML SEED CS1360 SMALL SEED BOX 1 5SBGSC010 SML SEED CS1360 SS FERTILIZER BOX 1 5SBGSC012 2ND SEED BOX CS1360 SECOND LARGE SEED BOX 1 5SBGSC014 NATGRSBOX CS1360 NATIVE GRASS BOX 1 56

57 Weights CS1384 Machine lbs Shipping lbs Base machine with 1 large grass seed box 2,004 2,124 Base machine with 1 large grass seed box + 1 small (legume) seed box 2,090 2,210 Base machine with 1 large grass seed box + 1 small (legume) seed box + 1 large stainless steel fertilizer box 2,321 2,441 Base machine with 1 large grass seed box + 1 small (legume) seed box + 1 large native grass seed box 2,411 2,531 Base machine with 2 large grass seed boxes + 1 small (legume) seed box 2,321 2,441 Small (legume) seed box only Large Grass Seed box only Stainless Steel box only Native Seed Box only Attachments for field Conversion (AFC's) Bundle Number Short Description Long Description Bundle Qty 5SBGSC005 SCRPPYWHLS CS1384 REAR PK SCRP POLYWHLS 1 5SBGSC007 SCRPCIWHLS CS1384 REAR PK SCRP CIWHLS 1 5SBGSC009 SML SEED CS1384 SMALL SEED BOX 1 5SBGSC011 FERT BOX CS1384 SS FERTILIZER BOX 1 5SBGSC013 2ND SEED BOX CS1384 SECOND LARGE SEED BOX 1 5SBGSC015 NATGRSBOX CS1384 NATIVE GRASS BOX 1 57

58 Notes 58

59 59

60 60