Power supply for fire detection and fire alarm systems, smoke and heat control systems, and other fire protection systems, series ZSP135-DR

Transcription

1

2 Power supply for fire detection and fire alarm systems, smoke and heat control systems, and other fire protection systems, series ZSP135-DR The power supply is a guaranteed source of 24V voltage. The wall box is outfitted with a lock and has space for two batteries. The built-in breaker supervised by the controller protects the internal battery bank against too deep discharge. The power supplies are devoted to devices of: fire detection and fire alarm systems according to EN 54-4/A2 smoke and heat control systems according to EN other fire protection systems, in particular as stipulated in section 12.2 of the Ordinance of the Polish Minister of Interior and Administration on (Dz.U. nr 143, poz. 1002, thereafter referred to as the Ordinance) The power supplies comply with EU directives: CPD (constructive products) 89/106/EEC, LVD (low voltage devices) 206/95/EC, EMC (electromagnetic compatibility) 204/108/EC. FUNCTIONS OF THE DEVICE uninterruptible 24V power supply monitoring of the mains voltage indication of a fault battery test monitoring of resistance (thus also continuity) of the battery circuit monitoring of the rectifier s operation full monitoring of the charging process and state of charge of batteries floating mode with temperature compensation fast charging of the battery with the charging current limitation protection of the batteries against too deep discharge monitoring of the battery fuse monitoring of fuses of both outputs monitoring of the internal temperature visual and remote indication of alarms The power supply monitors the resistance of the battery circuit this feature is obligatory after August 31, 2009 (the standard EN 54-4/A2). The power supply simultaneously complies with both EN 54-4 and EN (as well as with the Ordinance), thus one model of the power supply can serve diverse fire protection systems. The power supply has the certificate of compliance issued by CNBOP No. 1438/CPD/0163 and the certificate of approval No. 583/DC/CNBOP/2009 INDIVIDUAL PARAMETERS Index Maximal output Nominal output Maximal battery Dimensions Weight with current Imax b current Imax a capacity (WxHxD), mm batteries ZSP135-DR-2A-1 2.0A 1.0A 18Ah 390x350x90 18kg ZSP135-DR-3A-1 2.0A 18Ah 390x350x90 18kg 3.0A ZSP135-DR-3A-2 1.5A 28Ah 390x350x140 28kg ZSP135-DR-5A-1 4.0A 18Ah 390x350x90 18kg ZSP135-DR-5A-2 5.0A 3.5A 28Ah 390x350x140 28kg ZSP135-DR-5A-3 3.0A 40Ah 450x350x180 42kg ZSP135-DR-7A-1 6.0A 18Ah 390x350x90 18kg ZSP135-DR-7A-2 7.0A 5.5A 28Ah 390x350x140 28kg ZSP135-DR-7A-3 5.0A 40Ah 450x350x180 42kg 2

3 COMMON PARAMETERS Input Output Floating mode voltage (25ºC) Output voltage range Operational environment Working temperature range Resistance to corrosion Sinusoidal vibration 10 50Hz Hz Ingress protection EN Functional class EN Environmental class EN Environmental class, the Ordinance General Efficiency Temperature compensation coefficient Cooling Quiescent current Max. resistance of the battery circuit Max. battery charging current Standard compliance Electrical safety EMC immunity EMC interferences V 20 28V -25ºC...+55ºC, +75ºC over 2h 25 ppm SO 2 at +25º and 93% humidity 1g 3g IP 43 A 2 I min 77 82% -48mV/ ºC convection max 35mA 250mΩ 2A EN class I EN /A2 The Ordinance, section a g Radio disturbance EN 55022/A1 level B harmonic EN fluctuations EN Tester of the power supplies ZSP135 ZSP135-TST The tester ZSP135-TST is a portable device to carry out a fast check of all power supplies of series ZSP135-D and ZSP135-DR during their operation. The tester doesn t need separate power supply. It is connected to the maintenance socket, available in each power supply. The tester is a tool for personnel responsible for set-up and maintenance. It helps to diagnose the power supply and to find a cause of a malfunction without dismounting the power supply. CHARACTERISTIC FEATURES handy casing powered by ZSP135-D or ZSP135-DR direct connection to the tested power supply possibility to force the battery test LCD to show measured values FUNCTIONS OF THE DEVICE diagnostics and check of parameters of the power supply and the battery bank indications: - battery voltage - output voltage - battery charging current - time to wait until the next battery test and the voltage of the last performed test - value of the resistance of the battery circuit (ZSP135-DR only) - temperature inside the box check of continuity of the battery circuit ul. Toruńska 8, Gliwice, Poland, phone , fax

4 Power supplies of voice alarming systems ZDSO400 Voice alarming systems require a guaranteed source of voltage to ensure supply of power over a specified duration needed by efficient evacuation from endangered zones. MERAWEX has developed and manufactures power supplies of series ZDSO400 for voice alarming systems Praesideo and Plena by Bosch, and Sinaps by Ultrak and Honeywell. A standard 19 rack cabinet of height up to 50U forms the main frame of the system to host not only elements of the power supply, but also elements of the voice alarming system (amplifiers, controllers, etc.). The power system takes care about supplying the mains (primary) power as well as the backup power of 24V or 48V from own battery banks. The battery banks are protected against too deep discharge. It is possible to apply a single rack or a set of a few racks the system allows for operation in a distributed mode. Reliability of the system can be improved by adding a supplementary power supply unit which can be used also to increase charging current. The power supplies ZDSO400 comply with EU directives: CPD (constructive products) 89/106/EEC, LVD (low voltage devices) 206/95/EC, EMC (electromagnetic compatibility) 204/108/EC. FEATURES AND FUNCTIONS OF THE POWER SUPPLY ZDSO400 no limitation as for the number of rack cabinets in the system distribution of the mains and backup power to the modules of the voice alarming systems alarming in case of detected malfunctions of the system possibility to connect with a fire alarm control panel precise regulation of floating mode voltage temperature compensation fast charging of the battery with the charging current limitation monitoring of low and high battery voltage monitoring of continuity of battery circuits and protection of batteries against too deep discharge surge protection of the mains line visual, sound and remote indication of alarms history of events recorded in non volatile memory wheels as optional outfit of the cabinet indication of high resistance of the battery bank and circuits connected to it Having conducted supplementary tests against EN 54-4/A2, conformity and approval was recertified for the power supplies. certificate of conformity: certificate of approval: date: ZDSO400D-AK4 nr 2144/ / ZDSO400E-AK3 nr 2157/ / ZDSO400D-AK3 nr 1438/CPD/ / According to the obligatory since September 1, 2009 amendment A2 to EN 54-4 the power supplies have been extended by a measuring set consisting of the battery resistance meter RMB-1 and DC meters CP-100 in each battery string. The requirement to monitor high resistance of the battery bank is included in the standard EN for voice alarming systems too, because this standard refers to EN Adjustment of the power supplies to the amendment A2 is the necessary and sufficient condition that complete voice alarming systems continue to comply with the technical approvals used in the process of their certification. The monitoring of resistance of the battery circuit (backup source of power) increases reliability of the power system, thus also reliability of the whole voice alarming system. 4

5 BASIC PARAMETERS Size of the system Type of the 19 rack cabinet Usable height of the rack Number of amplifiers of the voice alarming systems Primary power (mains) Input voltage Surge protection of the mains line General Working temperature range Cooling Ingress protection Weight after setup Standard compliance Electrical safety EMC immunity EMC interferences 600x600 or 800x600 min 24U max 50U depending on the rack 1 phase 230V +10% -15% or 3 phases 3x230V/400V +10% -15% class III (D) 3kA C forced IP30 depending on the rack and configuration EN class I EN /A2 The Ordinance, section a g Radio disturbance EN 55022/A1 level B harmonic EN fluctuations EN Power supply of the fireman s microphone ZSP25-E-MS / ZSP25-D-MS The power supply is devoted to uninterruptible supply of power to a stand with the microphone operated by a fireman in distributed systems of voice alarming. It was designed in a wall box with a lock to protect against access by unauthorized persons. The box can be unlocked by a standard light fireman s axe. Backup of output voltage after a mains failure: 24h of standby, 0.5h of alarm. The power supplies ZSP25-E-MS and ZSP25-D-MS are integrated parts of the voice alarming systems Praesideo and Sinaps, respectively, certified by CNBOP. ul. Toruńska 8, Gliwice, Poland, phone , fax

6 Versatile modular power supplies of series Cameleon Versatile modular power supplies CAMELEON are a family of products of unified construction and power in the range between 150 and 600W. The standard voltage converters are offered independently as single output power supplies or are the basis for power supplies with supplementary functions. Basic voltage versions are: 12, 24 and 48V. Other versions are available on request. The single output power supplies can be used to power fiber optic interfaces or other devices in voice alarming systems. For uninterruptible operation of the powered equipment the battery backup version of the CAMELEON power supply is recommended to use. The version of the battery backup devices with monitoring of the battery has functionality complying with the standard EN 54-4 applicable in systems of fire detection and alarming. AVAILABLE VOLTAGES AND CURRENTS Nominal output current (power) Nominal output voltage 12V 10A (125W) 12A (150W) 16A (200W) 24A (300W) 32A (400W) 24V 6A (150W) 8A (200W) 12A (300W) 16A (400W) 24A (600W) 48V 3A (150W) 4A (200W) 6A (300W) 8A (400W) 12A (600W) BASIC PARAMETERS OF POWER SUPPLIES Input Frequency Power factor General Efficiency Working temperature range Ingress protection * - power supplies without PFC can operate in the range of Vdc V AC or VDC* Hz 0.95 up to 87% -33 C C IP20 CREATION OF THE INDEX OF THE POWER SUPPLY ZM 24V 12A B - 00 Nominal output voltage Attention: The floating mode voltage is preset in power supplies to cooperate with batteries Nominal output current Attention: The available output current of power supplies to cooperate with batteries is decreased by the charging current Construction discriminant 151, 201, 301 no PFC 200, 300, 400, 600 with PFC Installation version 00 screw terminals 10 sockets and plugs Built-in function none single output power supply R parallel work B cooperation with a battery bank P cooperation with a battery bank and monitoring of its state (compliance with EN 54-4) A cooperation with a battery bank and monitoring of its state, incl. high resistance (compliance with EN 54-4/A2) S custom made power supply 6

7 Battery backup power supplies in wall boxes CAMELEON BOX The power supplies Cameleon Box are dedicated to supply guaranteed DC voltage 12V, 24V or 48V up to 300W of power. The wall box is outfitted with a lock and three cable transits, and has space to mount batteries. FUNCTIONS OF THE DEVICE LEDs indicating the state of operation (POWER, BATTERY) overload protection of outputs and battery protection of the batteries against too deep discharge (LVDD) floating mode with temperature compensation (internal temperature probe) possibility to input an external alarm (option) optional indication of the state of primary and separately of secondary power LEDs on the box door and relays BASIC PARAMETERS Input Frequency Power factor Backup power source Nominal voltage of VRLA batteries Maximal capacity of the battery bank General Output power Efficiency Working temperature range Ingress protection * - power supplies of power up to 150W operate at voltage within the range of Vdc ** - for power supplies of power of 200 : 300W VAC, VDC* Hz 0.95** 12V 24V 48V 80Ah 40Ah 12Ah W up to 87% -33 C..+55 C IP43 CREATION OF THE INDEX OF THE POWER SUPPLY ZMS - 1B - 12V - 10A Box dimensions: 1B 390x350x90 2B 390x350x140 3B 450x350x180 Nominal output current Attention: The output current is decreased by the charging current. Nominal output voltage (12V, 24V, 48V) Attention: The floating mode voltage is preset. ul. Toruńska 8, Gliwice, Poland, phone , fax

8 Multi-output power supplies for CCTV ZW The power supplies are dedicated to supply DC voltage of 12V to CCTV cameras. Depending on version a unit can power up to 16 cameras independently. The power supplies are designed as wall boxes with mounted one or two power modules (MZ), and one or two output modules (MW). CHARACTERISTIC FEATURES regulated output voltage easy scalability of the number of outputs light compact construction (up to 2 kg) LEDs indicating proper operation of each output protection against overload or short circuit (fuse or polyswitch) relay indicating proper operation (option) surge protection of each output line (option) TABLE OF VERSIONS Index Number of outputs Type of protection Varistors Relay Index Number of outputs Type of protection Varistors Relay 8 ZW4-A T ZW12-A T ZW4-AW T х ZW12-AW T х ZW4-AP T х ZW12-AP T х ZW4-APW T х х ZW12-APW T х х 4 12 ZW4-B P ZW12-B P ZW4-BW P х ZW12-BW P х ZW4-BP P х ZW12-BP P х ZW4-BPW P х х ZW12-BPW P х х ZW8-A T ZW16-A T ZW8-AW T х ZW16-AW T х ZW8-AP T х ZW16-AP T х ZW8-APW T х х ZW16-APW T х х 8 16 ZW8-B P ZW16-B P ZW8-BW P х ZW16-BW P х ZW8-BP P х ZW16-BP P х ZW8-BPW Description Number of outputs number of protected outputs of the power supply Type of protection type of output protection T fuse P polyswitch P х х ZW16-BPW P х х Varistors outputs of output modules are protected additionally by varistors Relay a relay to indicate 12V voltage failure (three contacts)

9 TABLE OF VERSIONS OF OUTPUT MODULES MW Index Number of outputs Type of protection Varistors Relay Index Type of protection MW4-A T MW8-A T MW4-AW T х MW8-AW T х MW4-AP T х MW8-AP T х MW4-APW T х х MW8-APW T х х 4 8 MW4-B P MW8-B P MW4-BW P х MW8-BW P х MW4-BP P х MW8-BP P х MW4-BPW P х х MW8-BPW P х х Number of outputs Varistors Relay TABLE OF VERSIONS OF POWER MODULES MZ Index MZ-1 MZ-2 Description To cooperate with output modules MW4 To cooperate with output modules MW8 BASIC PARAMETERS OF THE POWER SUPPLY Input Output Number of outputs Maximal current Power Operational environment Allowable working temperature Allowable working humidity Electrical safety EMC immunity EMC interferences 230Vac +10% -15% 12Vdc 4, 8, 12 or A for each output (1A versions on request) 25W 130W -10ºC...+40ºC 20% 90% EN class I EN , EN /-3/-4/-5/-6/-8/-11 Radio disturbance EN 55022/A1 level B harmonic EN fluctuations EN Adapters 12V The adapters to supply DC voltage of 12V to IT and telecom equipment, devices of industrial automation and CCTV. They are outfitted with 180cm of cable terminated by a 5.5/2.1 plug. BASIC PARAMETERS OF THE POWER SUPPLY Input Vac Output 12Vdc Current 1250 ma Operational environment Allowable working temperature -10 C C Allowable working humidity 20%...90% Compliance with safety requirements Electrical safety EN , protection class II Level of EMC interferences class B (EN 55022) ul. Toruńska 8, Gliwice, Poland, phone , fax

10 Power supplies to cooperate with batteries EL25, EL50 The power supplies EL25 and EL50 are a regulated source of DC voltage, power of 25W and 50W, respectively. They are constant frequency switching power supplies. They are devoted to cooperate with a battery bank connected as a buffer. FUNCTIONS OF THE DEVICE UI output characteristic protection against overload or short circuit visual indication of presence of output voltage indication of battery mode indication of low battery possibility to cut off the load from output voltage CHARACTERISTIC FEATURES charging current limitation protection of the battery bank against too deep discharge possibility to switch the unit on from the battery cold start DIN rail clip theoretical MTBF of 1.5 million hours (according to Telcordia SR- 332, taking into account electrical stress of single elements) Input voltage VAC (47 63 Hz) Protection class Class I according to EN Weight 0.35kg Dimensions (HxWxD) mm 82 x 47 x 125 EMC immunity EN EN /-3/-4/-5/-6/-8/-11 Radio disturbance EN 55022/A1 level B EMC interferences harmonic EN fluctuations EN EL25-B EL25- D EL50-B EL50- D Output parameters 13.2V 26.4V 13.6V 27.2V Nominal current 1.4A 0.7A 2.8A 1.4A Output current limitation A A A 2 2.8A Charging current limitation A A A A to indicate low battery V V V V to disconnect the battery bank V V V V AGM batteries Maintenance free batteries are used to cooperate with battery backup power supplies. We offer maintenance free batteries of the following brands: Panasonic, Europower, SSB, Acumax and Alarmtec. Because of gas recombination there is no need to replace electrolyte, and batteries can be applied in rooms without dedicated forced ventilation. FEATURES AGM technology design life up to 15 years voltage of single monoblocks: 2V, 6V i 12V range of capacity from 0.8 to 300Ah small internal resistance operation possible in arbitrary orientation broad range of working temperature APPLICATION fire protection systems emergency light UPS telecom power systems backup power for industrial automation and control solar panel systems cash register and printers mobile and portable devices 10

11 ZKS24-4 AC/AC power supplies in IP65 casing The AC/AC power supplies are dedicated to power speed dome cameras. Two outputs (24Vac or 27Vac) allow for choosing the voltage depending on the distance between the power supply and camera. The power supply is enclosed in a plastic casing (ABS) of ingress protection IP65, suitable for fixing to a wall. CHARACTERISTIC FEATURES small dimensions IP65 casing output voltage 24 and 27Vac power 100VA BASIC PARAMETERS OF THE POWER SUPPLY Input power Frequency General Power Output voltage Output current Mechanical parameters Dimensions Weight * - both outputs can be loaded simultaneously up to total power of 100VA Vac 50Hz 100VA U1: 24Vac / U2: 27Vac 4A for 24Vac or 3.7A for 27Vac* 157 x 118 x 76 mm 2.0 kg Battery backup power supplies in wall boxes The power supplies ZB EL25 and ZB EL50 are designed as wall boxes. They cooperate with a battery bank connected as a buffer. The power supplies indicate the battery mode and low battery. They are outfitted with charging current limitation and protection of the battery bank against too deep discharge. CHARACTERISTIC FEATURES light compact construction output voltage 12 or 24Vdc charging current limitation protection of the battery bank against too deep discharge possibility to switch the unit on from the battery Input power Frequency General Output voltage Maximal output current Space for batteries Mechanical parameters Dimensions Weight (without batteries) ZB EL25-B ZB EL25-D ZB EL50-B ZB EL50-D Vac 47 63Hz 13.2V 26.4V 13.6V 27.2V 2A 7.2Ah 1A 2 x 5Ah 4A 7.2Ah 2A 2 x 5Ah 157 x 118 x 76 mm ~2.0 kg ul. Toruńska 8, Gliwice, Poland, phone , fax

12 12