J326XP-IM-4. Avanti J-26 XP. High-Performance Centrifuge. Instruction Manual

Transcription

1 J326XP-IM-4 Avanti J-26 XP High-Performance Centrifuge Instruction Manual

2 Symbol Symbol Symbole Símbolo Simbolo Title / Titel / Titre / Titulo / Titolo / / Dangerous voltage Gefährliche elektrische Spannung Courant haute tension Voltaje peligroso Pericolo: alta tensione! Attention, consult accompanying documents Achtung! Begleitpapiere beachten! Attention, consulter les documents joints Atención, consulte los documentos adjuntos Attenzione: consultare le informazioni allegate On (power) Ein (Netzverbindung) Marche (mise sous tension) Encendido Acceso (sotto tensione) Off (power) Aus (Netzverbindung) Arrêt (mise hors tension) Apagado Spento (fuori tensione) Protective earth (ground) Schutzleiteranschluß Liaison à la terre Puesta a tierra de protección Collegamento di protezione a terra Earth (ground) Erde Terre Tierra Scarica a terra

3 ! SAFETY NOTICE This safety notice summarizes information basic to the safe operation of the equipment described in this manual. The international symbol displayed above is a reminder that all safety instructions should be read and understood before installation, operation, maintenance, or repair of this instrument. When you see the symbol on other pages, pay special attention to the safety information presented. Observance of safety precautions will also help to avoid actions that could damage or adversely affect the performance of the centrifuge. Safety During Installation and/or Maintenance This centrifuge is designed to be installed by a Beckman Coulter field service representative. Installation by anyone other than authorized Beckman Coulter personnel invalidates any warranty covering the instrument. Any servicing of this equipment that requires removal of any covers can expose parts that involve the risk of electric shock or personal injury. Make sure that the power switch is turned off and the instrument is disconnected from the main power source, and refer such servicing to qualified personnel. Be sure to use the anchoring system to secure the centrifuge in place. The anchoring system is designed to reduce the possibility of injury or damage that could result from instrument movement in the event of a major rotor mishap. Do not replace any centrifuge components with parts not specified for use on this instrument. Electrical Safety To reduce the risk of electrical shock, this equipment uses a three or five-wire electrical cord and plug to connect this equipment to earth-ground. To preserve this safety feature: Make sure that the matching wall outlet receptacle is properly wired and earthgrounded. Check that the line voltage agrees with the voltage listed on the name-rating plate affixed to the centrifuge. Never use a three-to-two wire plug adapter. Never use a two-wire extension cord or a two-wire non-grounding type of multipleoutlet receptacle strip. Do not place containers holding liquid on or near the chamber door. If they spill, liquid may get into the centrifuge and damage electrical or mechanical components.

4 Safety Against Risk of Fire This centrifuge is not designed for use with materials capable of developing flammable or explosive vapors. Do not centrifuge such materials (for example, chloroform or ethyl alcohol) in this instrument nor handle or store them near the centrifuge. Mechanical Safety For safe operation of the equipment, observe the following: Use only the Beckman Coulter rotors and accessories designed for use in this centrifuge. Do not exceed the maximum rated speed of the rotor in use. NEVER attempt to slow or stop a rotor by hand. Do not lift or move the centrifuge while a rotor is spinning. NEVER attempt to override the door interlock system while the rotor is spinning. Do not lean on the centrifuge or place items on it while it is operating. Chemical and Biological Safety Normal operation may involve the use of solutions and test samples that are pathogenic, toxic, or radioactive. Such materials should not be used in this centrifuge, however, unless all necessary safety precautions are taken. Observe all cautionary information printed on the original solution containers prior to their use. Handle body fluids with care because they can transmit disease. No known test offers complete assurance that they are free of micro-organisms. Some of the most virulent Hepatitis (B and C) and HIV (I V) viruses, atypical mycobacteria, and certain systemic fungi further emphasize the need for aerosol protection. Handle other infectious samples according to good laboratory procedures and methods to prevent spread of disease. Because spills may generate aerosols, observe proper safety precautions for aerosol containment. Do not run toxic, pathogenic, or radioactive materials in this centrifuge without taking appropriate safety precautions. Biosafe containment should be used when Risk Group II materials (as identified in the World Health Organization Laboratory Biosafety Manual) are handled; materials of a higher group require more than one level of protection. Dispose of all waste solutions according to appropriate environmental health and safety guidelines. It is your responsibility to decontaminate the instrument and accessories before requesting service by Beckman Coulter.

5 J326XP-IM-4 May 2008 Avanti J-26 XP High-Performance Centrifuge Instruction Manual 2008 Beckman Coulter, Inc. Printed in the U.S.A. JUC-0608-PDF

6 Contents Page INTRODUCTION Certification vii Scope of this Manual vii Conventions viii Notes, Cautions, and Warnings viii Typographic Conventions ix Radio Interference ix Canadian Regulations x Recycling Label x SECTION 1: SPECIFICATIONS AND PREINSTALLATION REQUIREMENTS Specifications Control Features Operational Features Physical Data Available Rotors Preinstallation Requirements Electrical Requirements Single and Three-Phase Power Connections Additional Requirements for Three-Phase Power Connections Space and Location Requirements Securing the Centrifuge to the Floor Using J2 Series Rotors in the Avanti J Checking for Rotor Drive Pins Using the JA-18 Rotor Using the JCF-Z Continuous Flow/Zonal Rotor iii

7 Contents Page SECTION 2: DESCRIPTION Centrifuge Function and Safety Features Centrifuge Function Safety Features Housing and Door Rotor Chamber Drive Friction Reduction System (FRS) Temperature Sensing and Control Overtemp System Name Rating Plate Controls and Indicators Power Switch Control Panel SECTION 3: OPERATION Summary of Avanti J-26XP Run Steps Preparation and Loading Entering Run Parameters Selecting a Rotor Setting Run Speed Setting Run Time Setting Run Temperature Setting Acceleration and Deceleration Rates Setting Up an Elutriation Run Starting a Run Changing Parameters During a Run Changing Time Settings Stopping a Run Unloading the Centrifuge iv

8 Contents Page SECTION 4: TROUBLESHOOTING Diagnostic Messages Accessing the Rotor in Case of Power Failure JCF-Z Rotor Identification SECTION 5: CARE AND MAINTENANCE Maintenance Cleaning Decontamination Sterilization and Disinfection Replacing the Air Filter Circuit Breaker and Fuses Storage and Transport Storage Returning a Centrifuge Supply List Replacement Parts and Supplies APPENDIX: TEMPERATURE CALIBRATION PROCEDURE Warranty v

9 Illustrations Page Figure 1-1. Single-Phase Electrical Requirements Figure 1-2. Three-Phase Y Electrical Requirements Figure 1-3. Correct and Incorrect Three-Phase Power Configurations Figure 1-4. Rear View and Dimensions Figure 1-5. Checking the Rotor for Drive Pins Figure 2-1. The Power Switch Figure 2-2. The Control Panel Figure 3-1. Acceleration and Deceleration Settings Graph Figure 3-2. Elutriation Controls Figure 4-1. Emergency Door Release Latch Access Figure 4-2. Manual Door Release Figure 4-3. Venting the Chamber Vacuum Figure 4-4. Front Panel Retaining Strip Tables Page Table 1-1. Nominal Instrument Voltage Ratings for the Avanti J-26XP Table 1-2. Required Wire Connections Table 3-1. Acceleration Settings Table 3-2. Deceleration Settings Table 4-1. Diagnostic Message Chart vi

10 Introduction CERTIFICATION To ensure full system quality, Beckman Coulter Avanti J-26XP centrifuges are manufactured in a registered ISO 9001 or facility. They have been designed and tested to be compliant (when used with Beckman Coulter rotors) with the laboratory equipment reqirements of applicable regulatory agencies. Declarations of conformity and certificates of compliance are available at SCOPE OF THIS MANUAL This manual is designed to familiarize centrifuge users and site engineers with the Avanti J-26XP centrifuge, its functions, specifications, operation, and routine care and maintenance. We recommend that you read this entire manual, especially the SAFETY NOTICE and all safety-related information, before operating the instrument or performing instrument maintenance. Section 1 contains system specifications and instructions for preparing your site for centrifuge installation. Section 2 contains an overall description of the centrifuge, including a description of system controls and indicators. Section 3 summarizes procedures for operating the centrifuge. Section 4 lists system diagnostic messages, together with probable causes and user-performed corrective actions. Section 5 contains procedures for routine maintenance, as well as a brief list of supplies and replacement parts. The appendix contains a procedure to use when temperature control within ±1 C is required. vii

11 Introduction NOTE If the centrifuge is used in a manner other than specified in this manual, the safety and performance of this equipment could be impaired. Further, the use of any equipment other than that recommended by Beckman Coulter has not been evaluated for safety. Use of any equipment not specifically recommended in this manual is the sole responsibility of the user. CONVENTIONS Certain symbols are used in this manual to call out safety related and other important information. These international symbols may also be displayed on the centrifuge and are reproduced and described on the inside cover and/or below. NOTES, CAUTIONS, AND WARNINGS NOTE Used to call attention to information that should be followed during installation, use, and/or servicing of the equipment.! CAUTION Used to indicate a potentially hazardous situation which, if not avoided, may result in minor or moderate injury and/or mechanical damage. It is also used to alert against unsafe practices. viii

12 Introduction! WARNING Used whenever an action or condition may potentially cause personal injury or loss of life. Mechanical damage may also result. WARNING Indicates high voltage or risk of electric shock. Refer servicing of all areas displaying either symbol to qualified service personnel. TYPOGRAPHIC CONVENTIONS Certain typographic conventions are used throughout this manual to distinguish names of user interface components, such as keys and displays. Control knob names (for example, ROTOR and SPEED) appear in all capital letters. Key names (for example, [START] and [STOP]) appear in brackets. Display field names (for example, TEMP C or SPEED) appear in bold type. RADIO INTERFERENCE This instrument has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with this instruction manual, may cause interference to radio communications. Operation of this equipment in a residential area may cause interference, in which case the user will be required to correct the interference at his own expense. ix

13 Introduction CANADIAN REGULATIONS This digital apparatus does not exceed the Class A limits for radio noise emissions from digital apparatus as set out in the radio interference regulations of the Canadian Department of Communications. Le présent appareil numérique n émet pas de bruits radioélectriques dépassant les limites applicables aux appareils numériques de Classe A prescrites dans le reglement sur le brouillage radioelectrique édicté par le Ministère des Communications du Canada. RECYCLING LABEL This symbol is required in accordance with the Waste Electrical and Electronic Equipment (WEEE) Directive of the European Union. The presence of this marking on the product indicates: A28219-AA Note: On the instrument, the triangle background is yellow rather than gray. 1) The device was put on the European market after August 23, 2005 and 2) The device is not to be disposed via the municipal waste collection system of any member state of the European Union. It is very important that customers understand and follow all laws regarding the proper decontamination and safe disposal of electrical equipment. For Beckman Coulter products bearing this label please contact your dealer or local Beckman Coulter office for details on the take back program that will facilitate the proper collection, treatment, recovery, recycling and safe disposal of the device. x

14 1 Specifications and Preinstallation Requirements SPECIFICATIONS Only values with tolerances or limits are guaranteed data. Values without tolerances are informative data, without guarantee. CONTROL FEATURES CFC Speed Setting range to rpm (in 100-rpm increments below rpm, 500-rpm increments above rpm), or equivalent RCF (in 100 g increments) Elutriation speed setting range to rpm (in 10-rpm or 10 g increments) Speed display from 0 to rpm, display indicates actual rotor speed ±10 rpm from to rpm, indicates actual rotor speed ± 0.1%, or equivalent RCF Time Setting range to 180 min or continuous (hold) Time display indicates run time remaining (timed run) or elapsed time (hold run) Temperature Setting range to +40 C (in 1 C increments) Accuracy rotor temperature controlled to within ±2 C of set temperature (after equilibration)* Ambient temperature range to 38 C (60 to 100 F) Cooling fluid Refrigerant 404A (HFC) Acceleration maximum or slow Deceleration maximum, slow, or off * During transient conditions, such as acceleration and deceleration, rotor temperature may be outside this range. Refer to applicable rotor manuals for specific rotor operating range information. To reach temperatures above ambient, the centrifuge is dependent on the frictional heat generated inside the chamber during operation. At low run speeds or low ambient temperatures, the centrifuge may not be able to achieve some higher temperatures. 1-1

15 Specifications and Preinstallation Requirements OPERATIONAL FEATURES Door cm (2.4-in.) thick structural foam with steel plate Rotor chamber diameter cm (20 in.) Friction Reduction System (FRS) mm (7.5 in.) Hg PHYSICAL DATA Width cm (28 in.) Depth cm (34 in.) Depth (including air diverter extending from back panel) cm (40.25 in.) Height, door closed cm (34 in.) Height to top of control head cm (45.5 in.) Height to top of open door cm (58.7 in.) Weight kg (640 lb) Clearances (for adequate ventilation) Sides cm (3 in.) Back (place air diverter against the wall) cm (6.25 in.) Surface finish polyester control panel with polycarbonate coating overlay; polyurethane enamel on door and covers; acrylic baking enamel on other surfaces Electrical requirements 200/208/240-V, single-phase instrument VAC, 30 A, 50/60 Hz 230-V, single-phase instrument VAC, 30 A, 50 Hz 220/380-V plus neutral, three-phase instrument VAC plus neutral, 16 A, 50 Hz Electrical supply Class I Maximum heat dissipation into room under steady-state conditions kw (6900 Btu/h) Humidity restrictions <95% (noncondensing) Noise level 0.91 m (3 ft) in front of instrument at rpm dba Installation (overvoltage) category II Pollution degree ** Unbalanced three-phase. Split for single-phase operation internally. ** Normally, only nonconductive pollution occurs; occasionally, however, a temporary conductivity caused by condensation must be expected. 1-2

16 Specifications and Preinstallation Requirements AVAILABLE ROTORS Refer to the applicable rotor manual for complete rotor descriptions. Rotor Profile and Description Rotor Code Max RPM a Max RCF ( g) Max Capacity Rotor Manual Number JA Ti Fixed Angle, 34 (8 place) b rmax = 108 mm c ml J-TB-070 JA Fixed Angle, 34 (8 place) d rmax = 108 mm ml J-TB-056 JA Fixed Angle, 25 (24 place) d rmax = 106 mm (outer row) r max = 86 mm (inner row) ml J-TB-057 JA-21 Fixed Angle, 40 (18 place) r max = 102 mm ml J-TB-002 a Maximum speeds are based on a solution density of 1.2 g/ml with the following exceptions: the JA-18.1 rotor is rated for a density of 1.4 g/ml; the JCF-Z rotor is rated for a density of 1.45 g/ml; and the JE-5.0 rotor is rated for a density of 3 g/ml. b Temperature performance for the JA Ti rotor in the Avanti J-26XP is as follows: 15 C minimum at rpm (at 30 C ambient); 4 C minimum at rpm (30 C ambient). c Maximum speed for the JA Ti rotor is rpm in the Avanti J-26XP centrifuge, and rpm in the Avanti J-30I centrifuge. d Temperature performance for the JA and JA rotors in the Avanti J-26XP is as follows: 10 C minimum at rpm (at 30 C ambient); 4 C minimum at rpm (30 C ambient). e Maximum speed for the JS and JS rotor is rpm in the Avanti J-26XP centrifuge, and rpm in the Avanti J-30I centrifuge. f In the Avanti J-26XP, the JCF-Z Continuous Flow/Zonal Rotor can be used in the continuous flow and reorienting gradient zonal configurations only. Continued 1-3

17 Specifications and Preinstallation Requirements Rotor Profile and Description Rotor Code Max RPM a Max RCF ( g) Max Capacity Rotor Manual Number JA-20.1 Fixed Angle, 23 (32 place) r max = 115 mm (outer row) ml J-TB-022 r max = 98 mm (inner row) JA-20 Fixed Angle, 34 (8 place) r max = 108 mm ml J-TB-003 JA-18.1 Fixed Angle (24 place) 45 adapter r max = 116 mm ml J-TB adapter r max = 112 mm ml JA-18 Fixed Angle, 23 (10 place) r max = 132 mm ml J-TB-035 JA-17 Fixed Angle, 25 (6 place) r max = 132 mm ml J-TB-017 a Maximum speeds are based on a solution density of 1.2 g/ml with the following exceptions: the JA-18.1 rotor is rated for a density of 1.4 g/ml; the JCF-Z rotor is rated for a density of 1.45 g/ml; and the JE-5.0 rotor is rated for a density of 3 g/ml. b Temperature performance for the JA Ti rotor in the Avanti J-26XP is as follows: 15 C minimum at rpm (at 30 C ambient); 4 C minimum at rpm (30 C ambient). c Maximum speed for the JA Ti rotor is rpm in the Avanti J-26XP centrifuge, and rpm in the Avanti J-30I centrifuge. d Temperature performance for the JA and JA rotors in the Avanti J-26XP is as follows: 10 C minimum at rpm (at 30 C ambient); 4 C minimum at rpm (30 C ambient). e Maximum speed for the JS and JS rotor is rpm in the Avanti J-26XP centrifuge, and rpm in the Avanti J-30I centrifuge. f In the Avanti J-26XP, the JCF-Z Continuous Flow/Zonal Rotor can be used in the continuous flow and reorienting gradient zonal configurations only. Continued 1-4

18 Specifications and Preinstallation Requirements Rotor Profile and Description Rotor Code Max RPM a Max RCF ( g) Max Capacity Rotor Manual Number JLA Fixed Angle, 25 (6 place) r max = 134 mm ml J-TB-072 JA-14 Fixed Angle, 25 (6 place) r max = 137 mm ml J-TB-004 F14BCI-14x50cy Fixed Angle, 34 (14 place) r max = 153 mm F50C ml F14BCI-6x250y Fixed Angle, 23 (6 place) r max = 137 mm F ml JA-12 Fixed Angle, 35 (12 place) r max = 144 mm ml J-TB-051 a Maximum speeds are based on a solution density of 1.2 g/ml with the following exceptions: the JA-18.1 rotor is rated for a density of 1.4 g/ml; the JCF-Z rotor is rated for a density of 1.45 g/ml; and the JE-5.0 rotor is rated for a density of 3 g/ml. b Temperature performance for the JA Ti rotor in the Avanti J-26XP is as follows: 15 C minimum at rpm (at 30 C ambient); 4 C minimum at rpm (30 C ambient). c Maximum speed for the JA Ti rotor is rpm in the Avanti J-26XP centrifuge, and rpm in the Avanti J-30I centrifuge. d Temperature performance for the JA and JA rotors in the Avanti J-26XP is as follows: 10 C minimum at rpm (at 30 C ambient); 4 C minimum at rpm (30 C ambient). e Maximum speed for the JS and JS rotor is rpm in the Avanti J-26XP centrifuge, and rpm in the Avanti J-30I centrifuge. f In the Avanti J-26XP, the JCF-Z Continuous Flow/Zonal Rotor can be used in the continuous flow and reorienting gradient zonal configurations only. Continued 1-5

19 Specifications and Preinstallation Requirements Rotor Profile and Description Rotor Code Max RPM a Max RCF ( g) Max Capacity Rotor Manual Number JA-10 Fixed Angle, 25 (6 place) r max = 158 mm ml J-TB-006 JLA Fixed Angle, 20 (6 place) r max = 166 mm ml J-TB-048 F10BCI-6x500y Fixed Angle, 23 (6 place) r max = 158 mm F500 (previously 10.1) ml JLA Fixed Angle, 20 (4 place) r max = 185 mm ml J-TB-073 JLA Fixed Angle, 20 (6 place) r max = mm ml J-TB-073 a Maximum speeds are based on a solution density of 1.2 g/ml with the following exceptions: the JA-18.1 rotor is rated for a density of 1.4 g/ml; the JCF-Z rotor is rated for a density of 1.45 g/ml; and the JE-5.0 rotor is rated for a density of 3 g/ml. b Temperature performance for the JA Ti rotor in the Avanti J-26XP is as follows: 15 C minimum at rpm (at 30 C ambient); 4 C minimum at rpm (30 C ambient). c Maximum speed for the JA Ti rotor is rpm in the Avanti J-26XP centrifuge, and rpm in the Avanti J-30I centrifuge. d Temperature performance for the JA and JA rotors in the Avanti J-26XP is as follows: 10 C minimum at rpm (at 30 C ambient); 4 C minimum at rpm (30 C ambient). e Maximum speed for the JS and JS rotor is rpm in the Avanti J-26XP centrifuge, and rpm in the Avanti J-30I centrifuge. f In the Avanti J-26XP, the JCF-Z Continuous Flow/Zonal Rotor can be used in the continuous flow and reorienting gradient zonal configurations only. Continued 1-6

20 Specifications and Preinstallation Requirements Rotor Profile and Description Rotor Code Max RPM a Max RCF ( g) Max Capacity Rotor Manual Number JS Swinging Bucket (6 place) r max = 161 mm e ml J-TB-058 JS Swinging Bucket (6 place) r max = mm e ml J-TB-058 JS-13.1 Swinging Bucket (6 place) r max = 140 mm ml J-TB-036 JS-7.5 Swinging Bucket (4 place) r max = 165 mm ml J-TB-007 JS-5.3 Swinging Bucket (2 place) r max = mm microplates 8 deep-well plates 4 square-well plates J-TB-089 a Maximum speeds are based on a solution density of 1.2 g/ml with the following exceptions: the JA-18.1 rotor is rated for a density of 1.4 g/ml; the JCF-Z rotor is rated for a density of 1.45 g/ml; and the JE-5.0 rotor is rated for a density of 3 g/ml. b Temperature performance for the JA Ti rotor in the Avanti J-26XP is as follows: 15 C minimum at rpm (at 30 C ambient); 4 C minimum at rpm (30 C ambient). c Maximum speed for the JA Ti rotor is rpm in the Avanti J-26XP centrifuge, and rpm in the Avanti J-30I centrifuge. d Temperature performance for the JA and JA rotors in the Avanti J-26XP is as follows: 10 C minimum at rpm (at 30 C ambient); 4 C minimum at rpm (30 C ambient). e Maximum speed for the JS and JS rotor is rpm in the Avanti J-26XP centrifuge, and rpm in the Avanti J-30I centrifuge. f In the Avanti J-26XP, the JCF-Z Continuous Flow/Zonal Rotor can be used in the continuous flow and reorienting gradient zonal configurations only. Continued 1-7

21 Specifications and Preinstallation Requirements Rotor Profile and Description Rotor Code Max RPM a Max RCF ( g) Max Capacity Rotor Manual Number JS-4.3 Swinging Bucket (4 place) r max = 204 mm ml J-TB-050 JS-4.0 Swinging Bucket (4 place) r max = 226 mm liter 4 blood bags 12 microplates 148 RIA tubes J-TB-006 JCFZ ml (standard core) 1250 ml (large core) 240 ml (small core) JCFZ-IM JE-5.0 Elutriation Rotor r max JE5-IM large chamber = 168 mm ml standard chamber = 125 mm ml Sanderson chamber = 126 mm ml a Maximum speeds are based on a solution density of 1.2 g/ml with the following exceptions: the JA-18.1 rotor is rated for a density of 1.4 g/ml; the JCF-Z rotor is rated for a density of 1.45 g/ml; and the JE-5.0 rotor is rated for a density of 3 g/ml. b Temperature performance for the JA Ti rotor in the Avanti J-26XP is as follows: 15 C minimum at rpm (at 30 C ambient); 4 C minimum at rpm (30 C ambient). c Maximum speed for the JA Ti rotor is rpm in the Avanti J-26XP centrifuge, and rpm in the Avanti J-30I centrifuge. d Temperature performance for the JA and JA rotors in the Avanti J-26XP is as follows: 10 C minimum at rpm (at 30 C ambient); 4 C minimum at rpm (30 C ambient). e Maximum speed for the JS and JS rotor is rpm in the Avanti J-26XP centrifuge, and rpm in the Avanti J-30I centrifuge. f In the Avanti J-26XP, the JCF-Z Continuous Flow/Zonal Rotor can be used in the continuous flow and reorienting gradient zonal configurations only. 1-8

22 Specifications and Preinstallation Requirements PREINSTALLATION REQUIREMENTS Do not attempt to install this instrument. Its purchase price includes installation by Beckman Coulter personnel. Installation by anyone other than an authorized Beckman Coulter representative invalidates any warranty covering the instrument. Preinstallation requirements have been sent prior to shipment of the instrument. The following information is provided in case the centrifuge must be relocated. The centrifuge will be installed upon initial purchase by a Beckman Coulter Field Service representative after preinstallation requirements for power and site preparation have been met. The following equipment is required for preinstallation: Voltmeter For single phase centrifuges: two 30-ampere circuit breakers For three phase centrifuges: three 16-ampere circuit breakers Power receptacle (see Figure 1-1 or 1-2) Drill for drilling holes in the floor for installation of anchoring kit bolts (see SECURING THE CENTRIFUGE TO THE FLOOR, later in this section). A 9.5 mm ( 3 /8-inch) drill is required for concrete floors. A 6.4 mm ( 1 /4-inch) drill is required for wood floors. ELECTRICAL REQUIREMENTS Power to the centrifuge should originate directly from a main power line transformer at a power source known to be clear of erratic loads, spikes, and electromagnetic interference. Make sure that there are properly rated thermal circuit breakers at the service panel to protect the centrifuge circuit. If fuses must be used instead of the specified circuit breakers, the fuses may require a rating of greater than 30 amperes (for single-phase centrifuges) or greater than 16 amperes (for three-phase centrifuges). Terminate the open end of the harmonized cord with a certified single- or three-phase connector suitable for the power supplied in the country of intended use (see Table 1-1). Install only one centrifuge per circuit. 1-9

23 Specifications and Preinstallation Requirements Table 1-1. Nominal Supply Voltage Ratings for the Avanti J-26XP Nominal Instrument Voltage Rating Instrument Part Number Instrument Part Number (Elutriation System) Nominal Supply Frequency Power Cord and Plug Description Single-phase, 200/208/240 V V, 50/60 Hz, 30 A permanently attached three-wire UL/CSA-approved cord with NEMA type 6-30P plug Single-phase, 230 V V, 50 Hz, 30 A permanently attached three-wire CENELEC harmonized cord without plug Three-phase, 220/ 380 V + Neutral* V, plus neutral, 50 Hz, 16 A permanently attached five-wire CENELEC harmonized cord without plug * Unbalanced three-phase. Split for single-phase operation internally. To ensure safety, connect the instrument to a remote emergency switch (preferably outside the room where the centrifuge is housed, or adjacent to the exit from that room), to disconnect the centrifuge from the main power source in case of a malfunction.! WARNING To reduce the risk of electrical shock, this equipment uses a three-wire or five-wire electrical cord and plug to connect the centrifuge to earth-ground. To preserve this safety feature, make sure that the matching wall outlet receptacle is properly wired and earth-grounded. Prior to instrument purchase, the power configuration should be determined and the appropriate instrument ordered. SINGLE AND THREE-PHASE POWER CONNECTIONS Figure 1-1 shows the power connection for single-phase centrifuges, including earth-ground and two power leads with 30-ampere circuit breakers. Figure 1-2 shows the power connection for three-phase centrifuges, including earth-ground and three power leads with minimum 16-ampere circuit breakers and common neutral connection. Table 1-2 contains wiring information. 1-10

24 Specifications and Preinstallation Requirements 30-ampere Circuit Breaker Wall Outlet: Hubbell 9330, Bryant FR, or Equivalent (NEMA 6-30 R) Earth- Ground Measured Line Voltage 30-ampere Circuit Breaker Figure 1-1. Single-Phase Electrical Requirements 16-ampere Circuit Breaker Measured Line Voltage Phase to Phase Neutral 16-ampere Circuit Breaker 16-ampere Circuit Breaker Earth- Ground Figure 1-2. Three-Phase Y Electrical Requirements Table 1-2. Required Wire Connections Wire Insulation Color Terminal Harmonized Symbol North American Green/Yellow Earth ground Light Blue Neutral N L Brown Live or Line L L Black (three-phase connections only) Live or Line (qty 2) L 1-11

25 Specifications and Preinstallation Requirements ADDITIONAL REQUIREMENTS FOR THREE-PHASE POWER CONNECTIONS For three-phase power service to the centrifuge, use the Y connected configuration shown in Figure 1-3. Also note the following information: The steady state current draw of the centrifuge can be as high as 12 amperes per phase, depending on the voltage. Inrush current to the centrifuge is 100 amperes for up to 2 seconds during the refrigeration start period. Circuit breakers, whether thermal or magnetic actuating, must be a motor start delay type. The centrifuge can tolerate a drop of 15 volts during the start period at low line voltage (see Figure 1-3 for the acceptable voltage ranges). The mains power for the centrifuge must be of sufficient wire gauge to provide this condition. The wire gauge required at a particular site must be determined by a facilities engineer at that site. Correct Configuration Y Incorrect Configuration Delta Safety Ground N Circuit Common (Neutral) Figure 1-3. Correct and Incorrect Three-Phase Power Configurations The centrifuge can tolerate a drop of 15 volts during the start period at low line voltage (see Figure 1-3 for the acceptable voltage ranges). The mains power for the centrifuge must be of sufficient wire gauge to provide this condition. The wire gauge required at a particular site must be determined by a facilities engineer at that site. 1-12

26 Specifications and Preinstallation Requirements SPACE AND LOCATION REQUIREMENTS Locate the instrument on a clean, level floor. Select a location away from heat-producing laboratory equipment. If ambient temperature exceeds 38 C (100 F), premature component failure may result. In addition to space for the centrifuge, allow a 7.7-cm (3-in.) clearance on each side of the centrifuge and a 16-cm (6.25-in.) clearance behind the instrument for air circulation. The centrifuge must have adequate air ventilation to ensure compliance to local requirements for vapors produced during centrifuge operation. Position the centrifuge so that the air diverter, shown in Figure 1-4, touches the wall behind the centrifuge. Place the power cord to one side of the air diverter. To avoid damaging the power cord when installing or moving the centrifuge, be sure to move the cord out of the way before pushing the centrifuge towards the wall.! WARNING Do not place the centrifuge near areas containing flammable reagents or combustible fluids. Vapors from these materials could enter the instrument s air system and be ignited. SECURING THE CENTRIFUGE TO THE FLOOR Avanti J series centrifuges are certified to meet the requirements of the European CE mark. To meet these requirements, the centrifuge must be secured to the floor using the anchoring hardware shipped with the instrument. This will prevent the centrifuge from moving in the unlikely event of a rotor mishap. Complete instructions for installing the anchoring kit are packaged with the hardware, which is shipped with the centrifuge. The instructions (publication J325-TB-003) include a full-size template to be used as a guide for drilling holes in the floor. Refer to this document for additional installation instructions. 1-13

27 Specifications and Preinstallation Requirements cm in Air Exit Power Cable 1.8 m 6.0 ft. Air Diverter Depth Air Intake Figure 1-4. Rear View and Dimensions NOTE Beckman Coulter representatives are not equipped to drill holes in your floor. The holes must be drilled before your scheduled installation. 1-14

28 Specifications and Preinstallation Requirements USING J2 SERIES ROTORS IN THE AVANTI J! CAUTION Do not use the Beckman Coulter JA-10, JS-7.5, JA-14, or JS-13 rotors in the Avanti J-26XP centrifuge before reading this information. CHECKING FOR ROTOR DRIVE PINS Rotors used in Avanti J series centrifuges must have drive pins in the rotor drive hole (see Figure 1-5). These drive pins engage with the centrifuge spindle hub to ensure that the rotor does not slip during acceleration. Some Beckman Coulter rotors, including the JA-10, the JS-7.5, the JA-14, and the JS-13, have been manufactured without drive pins because pins were not needed when these rotors were used in J2 series centrifuges. The rotor pins are positioned parallel to the BECKMAN name engraved at the center of the rotor body (see Figure 1-5). Knowing the pin orientation before you install the rotor will help to ensure that you position the rotor properly on the hub, minimizing the chance of hub damage. Check all J2 series rotors for drive pins before using them in an Avanti J series centrifuge and do not use rotors without drive pins in the Avanti J. To check for drive pins, hold the rotor up or turn it on its side and look into the drive hole. If you do not see two metal pins in the hole, do not use the rotor in the Avanti J. Call your local Beckman Coulter office for information on returning the rotor to the factory for upgrading. USING THE JA-18 ROTOR In Avanti J series centrifuges, the JA-18 rotor must be run with the lid attached. See the JA-18 rotor manual (publication J-TB-035) for complete rotor usage instructions. 1-15

29 Specifications and Preinstallation Requirements BECKMAN Rotor Drive Hole Drive Pins (Angled pins shown; pins can also be vertical or horizontal.) Drive Spindle Assembly BECKMAN Top View Side View Figure 1-5. Checking the Rotor for Drive Pins USING THE JCF-Z CONTINUOUS FLOW/ZONAL ROTOR Zonal Bracket Kits A special bracket and mounting hardware are required when the JCF-Z Continuous Flow/Zonal Rotor is used. These parts are contained in the Zonal Bracket Kit (part number ). The Zonal Bracket Kit includes a bracket, mounting hardware, and assembly instructions. This kit is for use with Cole-Parmer tubing size 16 (6.4 mm [ 1 /4-in.] O.D.), the tubing size most commonly used with the JCF-Z rotor. Two additional kits are available, one which contains adapters for size 14 tubing (4.8 mm [ 3 /16-in.] O.D.) and one which contains adapters for size 15 tubing (9.6 mm [ 3 /8-in.] O.D.). If you wish to use 1-16

30 Specifications and Preinstallation Requirements either of these sizes of tubing, you will need to purchase one of these kits in addition to the basic kit (366431). See REPLACEMENT PARTS AND SUPPLIES in Section 5 for a complete list of Zonal Bracket Kit part numbers and kit contents. Ensuring Correct JCF-Z Continuous Flow/Zonal Rotor Identification The centrifuge s rotor identification system can, under two specific conditions, misidentify the JCF-Z continuous flow/zonal rotor. These conditions and corrective actions are listed below. NOTE JCF-Z rotors manufactured after March, 1997, contain special magnets that ensure correct rotor identification in Avanti J series centrifuges. We recommend that older JCF-Z rotors be returned to the Beckman Coulter factory for addition of the magnets before use in the Avanti J-26XP. Call Beckman Coulter Field Service 1 for more information. The following information pertains to JCF-Z rotors manufactured before March, 1997, and to JCF-Z rotors that have not been modified at the factory. When the bearings in the JCF-Z rotating seal assembly get old or worn, the resulting drag on the bearings changes the rotor s dynamic properties, making them similar to those of several Beckman Coulter fixed angle rotors. If rotor misidentification occurs when your JCF-Z rotor is used, first perform three runs from 0 to 5000 rpm and back to 0 rpm. If rotor misidentification recurs, replace the bearings. See the JCF-Z rotor instruction manual (publication JCFZ-IM) for bearing replacement instructions. Be sure to follow instructions in the next paragraph below for wearing in the bearings. On the first few uses of a new JCF-Z rotor, or when the bearings have been replaced in an older JCF-Z rotor, lubrication has not yet been thoroughly distributed around the bearings in the bearing housing. The excess lubrication produces drag on the bearings, 1 In the United States, call Outside the U.S., contact your local Beckman Coulter office. 1-17

31 Specifications and Preinstallation Requirements which can change the rotor s dynamic properties enough to cause rotor misidentification. To wear in the bearings and distribute the lubrication, perform three runs from 0 to 5000 rpm and back to0rpm. NOTE If the JCF-Z rotor is misidentified, the run speed will be limited to the maximum speed for the identified rotor. (The maximum speed for the JCF-Z rotor is rpm.) 1-18

32 2 Description This section describes the Avanti J-26XP centrifuge hardware components and their functions. It also describes system safety features and centrifuge controls and displays. Refer to the applicable rotor manual for rotor descriptions. CENTRIFUGE FUNCTION AND SAFETY FEATURES CENTRIFUGE FUNCTION The Avanti J-26XP is a refrigerated centrifuge that generates centrifugal forces required for a wide variety of applications. Together with the Beckman Coulter rotors designed for use in this centrifuge, applications include: Routine processing such as sample preparations, pelleting, extractions, purifications, concentrations, phase separations, and spin column and spin filter centrifugations. Rapid sedimentation of protein precipitates, large particles, and cell debris. Preparation of subcellular organelles such as mitochondria, nuclei, chloroplasts, and crude microsomes. Separation of blood cells and cellular components. Pelleting of prokaryotic and eukaryotic cells Gradient separation, for example, Ficoll-Hypaque 1 and Percoll. 1 1 Registered trademarks of Pharmacia AB. 2-1

33 Description Nucleic acid precipitation. Virus isolation. Bacteriophage isolation. The Avanti J-26XP centrifuge is microprocessor-controlled, providing interactive operation. 2 The centrifuge features a brushless switched-reluctance drive motor, 3 an automatic rotor identification system, FRS (friction reduction system) vacuum control circuitry, and a temperature control system with automatic temperature compensation unique for each compatible rotor. The user interface has a digital display, which can be toggled to show either actual centrifuge values or user-entered setup values, knobs for parameter entry, and touch keys. Diagnostic messages on the control panel will light to alert the operator to conditions that may need attention. SAFETY FEATURES The Avanti J-26XP centrifuge has been designed and tested to operate safety indoors at altitudes up to m (6 562 ft). Safety features include the following. An electromechanical door lock system prevents operator contact with spinning rotors and prevents run initiation unless the door is shut and locked. The door locks when [START] is pressed, or when the POWER switch is turned off. A steel casing surrounds the rotor chamber to provide operator protection in the unlikely event of a rotor mishap. An automatic rotor identification system detects which rotor is installed and prevents the rotor from running above its maximum rated speed. An imbalance detector monitors the system during operation, causing automatic shutdown if rotor loads are severely out of balance. 2 Avanti J-26XP software and firmware copyright 2005 by Beckman Coulter, Inc., Palo Alto, CA, U.S.A. 3 Manufactured under license from Switched Reluctance Drives Limited, Harrogate, U.K. 2-2

34 Description HOUSING AND DOOR The instrument control housing is made of aluminum and molded structural foam. The door and structural-foam cover panels are finished with polyurethane enamel. The control panel is covered by a protective overlay made of coated polycarbonate. The door is opened by stepping on a foot pedal, which is located at the bottom right front of the instrument. The door is hinged at the back left to open at a 60-degree angle to the centrifuge side panels, providing clearance for loading and unloading of the centrifuge. In the event of a power failure, the door can be manually unlocked for sample recovery (see Section 4, TROUBLESHOOTING). ROTOR CHAMBER The rotor chamber is made of stainless steel to resist corrosion. A rubber gasket around the chamber opening ensures sealing. (Instrument gaskets have not been qualified as bioseals for aerosol containment.) DRIVE The drive spindle is directly driven by a brushless, high-torque, switched-reluctance motor. The instrument s resilient suspension minimizes disturbance of the sample during acceleration and deceleration, and reduces damage to the drive spindle if an imbalance occurs during centrifugation. FRICTION REDUCTION SYSTEM (FRS) The friction reduction system (FRS) uses a mechanical rotary vane vacuum pump to reduce chamber pressure to approximately onequarter atmosphere (190 mm Hg). The pump turns on after the run is started, before rotor friction reaches a high level. When the required vacuum level is reached, the pump turns off. Vacuum in the chamber is vented during rotor deceleration. 2-3

35 Description TEMPERATURE SENSING AND CONTROL The temperature control system is cooled by circulation of a non-cfc-based refrigerant. The temperature control system is activated when the centrifuge power is on and when the door is closed. A thermistor in the rotor chamber continuously monitors the chamber temperature. The system calculates the chamber temperature required to maintain the set rotor temperature, ±2 C. Although the chamber temperature fluctuates during operation, the rotor s large mass keeps the sample temperature substantially constant. At the end of a run, the system continues controlling the temperature to prevent freezing or overheating (more than 4 C over set temperature) of the sample. OVERTEMP SYSTEM An overtemp (over temperature) system provides sample protection and safety for the user. During a run, if the system temperature rises 4 C above the set temperature, the TEMP diagnostic will light. The run will continue, unless stopped by the user. If the temperature rises 8 C above the set temperature, the system will shut down (using maximum brake). The system will always shut down (using maximum brake) if the system temperature reaches 50 C. The centrifuge cannot be restarted until the chamber has cooled. NAME RATING PLATE The name rating plate is affixed to the rear of the centrifuge. Check that the line voltage agrees with the voltage listed on this name rating plate before connecting the centrifuge. Always mention the serial number and the model number shown when corresponding with Beckman Coulter regarding your centrifuge. 2-4

36 Description CONTROLS AND INDICATORS POWER SWITCH The power switch is located below the control panel (see Figure 2-1). This two-position rocker switch (I, on; O, off) controls electrical power to the centrifuge. Figure 2-1. The Power Switch CONTROL PANEL The control panel (Figure 2-2) is mounted at an angle on the centrifuge top rear for easy visibility and access. It contains a digital display for actual and setup values, knobs and touch keys for parameter entry, and additional touch keys for system control. Digital Display ROTOR ID SPEED TIME RPM/RCF RPM HR:MIN TEMP SET ACTUAL SET/ ACTUAL ROTOR JA JS JLA SPEED TIME TEMP C JSP JV JCF JE RPM/ RCF TIME/ HOLD MAX SLOW MAX SLOW OFF FRS ROTOR IMBAL SPEED DOOR SYS POWER DRIVE REFR TEMP ACCEL DECEL CLEAR START STOP Figure 2-2. The Control Panel 2-5

37 Description Digital Display The display shows current status of the instrument whenever the power is turned on. The display shows both actual centrifuge values and user-set parameters. The [SET/ACTUAL] key is used to toggle between the two views. During a run, actual values are displayed. If you turn a knob (other than the TIME knob) during operation, the display will change to show the set values. If no parameters are entered or changed for 5 seconds, the display will revert to showing actual values. During a timed run, the TIME display shows the remaining run time in hours and minutes. The TIME display begins counting down when [START] is pressed and continues counting down to 0, when deceleration begins. When the rotor decelerates to 0 rpm, End flashes in the TIME display. When HOLD is selected (no run time is specified), the TIME display shows the time elapsed since [START] was pressed. After 3 hours (180 minutes) have elapsed, the timer will reset to 0 and continue counting elapsed time until [STOP] is pressed. Knobs and Touch Keys The rotor name, speed, time, and temperature settings are entered by turning the appropriate knob until the required value is displayed. Touch keys allow the user to start and stop the centrifuge, and to select speed mode (RPM or RCF), time mode (specific run length or hold for continuous operation), and acceleration and deceleration rates, and to toggle the display between set and actual values. ROTOR Knob ROTOR JS JA JLA JSP JV JCF JE Used to select the rotor in use. As the knob is turned, the name of each Beckman Coulter rotor that can be run in the centrifuge appears in succession in the ROTOR ID display, and the LED by each rotor type abbreviation (JCF: continuous flow rotors; JSP: special type rotors; JS: swinging bucket rotors; JA: fixed angle rotors; JLA: lightweight fixed angle rotors; JV: vertical tube rotors; JE: elutriator rotors) lights when appropriate. 2-6