NEMA Control. Contactors & Starters Index

Transcription

1 Contactors & Starters Index Control Description Page Number General Information - TM... AC Magnetic Contactors - TM... AC Magnetic Reversing Contactors - TM... 6 AC Magnetic Starters - TM... AC Magnetic Reversing Starters - TM... 8 AC Magnetic Two Speed Starters - TM... 9 General Information Combination Units - TM... AC Magnetic Combination Starters - TM... AC Magnetic Combination Reversing Starters - TM... 8 AC Magnetic Two Speed Combination Starters - TM... AC Magnetic Reduced Voltage A\T Starters - TM... 6 AC Magnetic Wye Delta Starters - TM... 6 AC Magnetic Part Winding Starters - TM... AC Pump Panels - Simplex... 8 AC Panel Mounted Overload Relay... Heater Tables, TM, HP Starter... Factory Modifications - TM... 6 Field Modifications - TM... 9 Renewal Parts - TM... Dimensions - TM... Engineering Data - Diagrams... Catalog Ordering Data... 6 Series AC Rated Contactors... 6

2 TM - Control General Information Auxiliary Contacts -Auxiliary contact blocks may be added with the starter in place, without tools. The same block is used on sizes thru size as either N.O. or N.C.. A total of auxiliary contacts can be added. The addition of side mounting kits allows a total of 8 auxiliary contacts throughsize. Power Pole - Full rated power poles, N.O. or N.C. through size, may be field added, without coil change. A tie pole with N.O. contacts is available for twospeed single winding (consequent pole) motor applications. Operating Coils - All coils are encapsulated. thru are plug-in type and each is factory tested twice, for long reliable service. Coil changes are not required for any combination of add-on accessories. Power Wiring - Up-front terminals and straight through design make power wiring easy. As few as connection points per pole reduces the possibility of loose connections and contributes to the reliability of the starter. Contact Inspection - Loosen captive screws and remove the contact carrier, through size. Adapter Plate - Allows use of Type TM starters in place of other make s thru size, without drilling new mounting holes. The adapter plate holes align with those of most other starters thru size - proof of the TM compact design. Overload Relay - Available with ambient compensation (green reset rod) or non-ambient compensation (red reset rod). An easily accessible +, adjust-ment knob can be locked at the % setting. High accuracy of repetitive trip is assured by factory testing every unit twice. Heaters - Heater numbers are stamped on the surface for easy identification. The same heaters are used for TM & HP series overload relays for both ambient and non-ambient compensated overload relays. 8 Reliability - The basic contactor design, using polysulphone and teflon guides, melamine and rosite moldings along with stainless steel springs, provides exceptional electrical and mechanical life. The operating state is clearly visible from the front, indicated by the position of the contact carrier.the contactor is easily operated from the front for circuit checking. Versatility - Uniform mounting dimensions Add-on auxiliary contacts Plug-in coils Accessories, such as power pole, mechanical interlock pro-vides maximum versatility and flexibility of inventory panel layout and installation. Self-rising saddle-clamps are included on all control terminals for quick wiring.

3 General Information Control - TM 8 Compact - Integral overload relay design, with straight through power cable design, provides compact overall size. Straight through wiring reduces overall panel area for a wired device. Uniform mounting dimensions, along with mechanical interlock design, makes reversing devices and other mechanically interlock devices the same height and depth as nonreversing. This allows intermixing in rows and saves panel space. Uniform Mounting Dimensions - Only mounting plate sizes for through starters. One mounting plate for sizes -, the second for sizes &. This provides great flexibility for intermixing starter sizes in rows and reduces panel layout time. Pilot Device Kits - Operator devices may be added in the field. Push button and pilot light kits for non-combination enclosures are suitable for use in Type, &. This simplifies selection and increases flexibility.

4 TM - Control General Information Non-Reversing ulletin 6 Starters. ulletin Contactors. -6. Type, & s. -. Type R. ulletin 6 Starters are available single phase through size P, phase through size 6. ulletin Contactors are available & pole through size 6 and pole thru size. Reversing ulletin 6 Starters. ulletin 6 Contactors. -6. Type,, s ulletin 6 reversing starters and ulletin 6 reversing contactors include mechanical and electrical interlocks. Multi-Speed ulletin 6 Starters. -. Type, & s. ulletin 6 multi-speed starters are designed for two-speed, single winding (consequent pole) and two-speed, two winding (separate winding) motor applications. Mechanical and electrical interlocks are included. Starters for three and four speed motor applications can also be supplied. 8

5 AC Contactors Control - TM AC Contactors - ulletin TM -Pole, Single Phase Maximum Motor Starter Horsepower Rating Amps. Contin- V V V uous Pole, Single Phase / Pole, Three Phase 6 Pole, Three Phase 6 / Contin- V V V uous Type General Purpose Catalog No. Price TAA - TA - TA - TAA - TA - TA - TA - TA - TA - TA - TA - TA - TA - $ Type Watertight Catalog No. Price Use TW - TW - Use TW - TW - TW - TW - TAA -. Use Use TA -. TW - 9. TT - TA -. TW TT - TA TW - 8. TT - TA -. TW TT - TA - 8. TW -. TT - UA -. UW UT - See Vacuum Contactors in Section A TW - TW - TW - TW - TW - $ Type Industrial - Dust-tight Catalog No. Price Use TT - TT - Use TT - TT - TT - TT - TT - TT - TT - TT - TT - Catalog No. Price $ TUA - $.. TU TU Consult Factory or See Vacuum Contactors in Section A Consult Factory or See Vacuum Contactors in Section A Open Type TUA - TU - TU - TU - TU - TUA - TU - TU - TU - TU - TU - UU - TU - TU - TU - TU - TU Note:.. Price includes contactor complete with one N.O. control-circuit contact. This unit replaces T (size ) and is not interchangeable. Ordering Information Use complete catalog number. Replace the () with the suffix from coil table. Engineering Data - see Page Modifications - see Page 6 Renewal Parts - see Page Dimensions - see Page Coil Volt/Hertz /6 or / -/6 or / -/6 or / -8/6 or / -6/6 or / -8/6 Suffix Discount Schedule JC

6 TM - Control AC Reversing Contactors AC Reversing Contactors - ulletin 6 TM Pole, Three Phase Maximum Motor Horsepower Rating V V 6- V TAA - TA - 9. TW - 6. TT - 8. TU - TA - 6. TW - 8. TT -. TU - TA - 6. TW -. TT -. TU - TA -. TW - 9. TT - 6. TU - TA TW - 6. TT TU - UA - 9. UW -. UT -. UU - See Vacuum Contactors in Section A 6 Type General Purpose Catalog No. Price Type Type Open Type Watertight Industrial - Dust-tight Catalog No. Price Catalog No. Price Catalog No. Price $ 68. TWA - $. Use $ TUA - $ Plug-Stop or Jogging Duty ICS Notes: Price includes contactor complete with one N.O. contact on each contactor. All contactors are mechanically and electrically interlocked. For plug-stop or jogging duty, where operations exceed times a minute, contactor size should be chosen in accordance with Standard ICS --, as listed in table. This unit replaces T (size ) and is not interchangeable. 6 Horsepower Ratings - Three Phase, 6Hz V V 8V 6/V 6 \ 6 Ordering Information Use complete catalog number. Replace the () with the suffix from coil table. Engineering Data - see Page Modifications - see Page 6 Renewal Parts - see Page Dimensions - see Page Coil Volt/Hertz /6 or / -/6 or / -/6 or / -8/6 or / -6/6 or / -8/6 Suffix Discount Schedule JC

7 AC Non-Reversing Starters Control - TM AC Non-Reversing Starters - ulletin 6 TM Pole, Single Phase (requires overload heater) P Maximum Motor Horsepower Rating Contin- V V V uous / 9 8 Type General Purpose Catalog No. Price TAAA - TAA - TAA - TAAP Pole, Three Phase (requires overload heaters) 6- Contin- V V V uous $ Type Watertight Catalog No. Use size TWA - TWA - TWAP Price $ Type Industrial - Dust-tight Catalog No. Price Use TTA - TTA - TTAP $ Open Type Catalog No. TUA - TU - TU - TUP - TU - 9 TAAA - 8. Use size Use TUA - 8 TAA -. TWA - 8. TTA - 6. TU - TAA - 9. TWA - 9. TTA TU - TAA - 9. TWA TTA - 6. TU - 9 TAA - 6. TWA - 8. TTA - 9. TU - TAA TWA - 8. TTA TU - UAA UWA -. UTA -. UU - 6 See Vacuum Contactors in Section A Price $ Note:. Price includes starter complete with one N.O. contact on each contactor and phase overload relay less heaters.. This unit replaces T (size ) and is not interchangeable.. For Ambient Compensated overload see. Ordering Information Use complete catalog number. Replace the () with the suffix from coil table. Order heaters at $8 each. Engineering Data - see Page Modifications - see Page 6 Renewal Parts - see Page Heater Tables - see Page Dimensions - see Page Coil Volt/Hertz /6 or / -/6 or / -/6 or / -8/6 or / -6/6 or / -8/6 Suffix Discount Schedule JC

8 TM - Control AC Reversing Starters AC Reversing Starters - ulletin 6 TM Pole, Three Phase (requires overload heaters) Maximum Motor Horsepower Rating General Purpose 6- V V V Catalog No. Price 6 Watertight Catalog No. Price Industrial - Dust-tight Catalog No. Price $ Open Type Catalog No. TUA - TU - TU - TU - TU - TU - UU - TAAA - $ 88. TWAA - $ 8. Use TAA - 9. TWA -. TTA TAA - 6. TWA - 88 TTA -. TAA -. TWA -. TTA -. TAA - 6. TWA -. TTA - 6. TAA TWA TTA UAA UWA UTA See Vacuum Contactors in Section A Price $ Plug-Stop or Jogging Duty ICS -- Horsepower Ratings - Three Phase Note:. Includes starter complete with one N.O. contact on each contactor and phase overload relay less heaters. All starters are mechanically and electrically interlocked.. For plug-stop or jogging duty or where operations exceed per minute, starter sizes should be chosen in accordance with Standard ICS --, as listed in table.. This unit replaces T (size ) and is not interchangeable.. For Ambient Compensated overload see. 6 V 6 Hz 6 V 6 Hz 8V Hz 6/V 6 Hz 6 Ordering Information Coil Volt/Hertz Suffix Use complete catalog number. Replace the () with the suffix from coil table. Order heaters at $8 each. Engineering Data - see Page Modifications - see Page 6 Renewal Parts - see Page Heater Tables - see Page Dimensions - see Page /6 or / -/6 or / -/6 or / -8/6 or / -6/6 or / -8/ Discount Schedule JC

9 AC Two Speed Starters Control - TM AC Two Speed Non Combination Starters - ulletin 6 8 Speed, Single Winding (consequent pole) () () ( ) () () (6) () () () () () () () ( ) () () () () TAAC - TAAC - TAAC - TAAC - TAAC - $ Speed, Double Winding (separate winding) () () ( ) () () () () () () () () ( ) () () () TAAS - TAAS - TAAS - TAAS - TAAS TWAS - TWAS - TWAS - TWAS - TWAS TTAS - TTAS - TTAS - TTAS - TTAS - (6) () () Consult Factory. Maximum Motor Horsepower Rating Constant or Variable Torque (Constant Horsepower) 6- V V V General Purpose Catalog No. Price Watertight TWAC - $. TWAC - TWAC - TWAC - TWAC - TTAC - TTAC - TTAC - TTAC - TTAC - $ TUOC - TUOC - TUOC - TUOC - TUOC - Note: Includes starter complete with one N.O. contact on each contactor and two phase overload relays less heaters. All starters are mechanically and electrically interlocked. Six (6) heaters are required, for each speed rated for HP ratings Industrial - Dust-tight Open Type Catalog No. Price Catalog No. Price Catalog No. Price Consult Factory TUOS - TUOS - TUOS - TUOS - TUOS - $ Ordering Information Coil Volt/Hertz Suffix Use complete catalog number. Replace the () with the suffix from coil table. Order heaters at $8 each. Engineering Data - see Page Modicications - see Page 6 Renewal Parts - see Page Heater Tables - see Page Dimensions - see Page 6 /6 or / -/6 or / -/6 or / -8/6 or / -6/6 or / -8/ Discount Schedule JC 9

10 TM - Control General Information Combination Starters & Contactors Non-Reversing ulletin 68 with disconnect switch, fusible and non-fusible. ulletin 6 with Circuit reaker V thermal magnetic trip breaker or 6V adjustable magnetic trip MCP. breaker. -6., & enclosures. Choose standard, compact or extra-wide enclosure style of enclosure for s, &. All three styles are available in, & enclosure. s & are available in standard and extrawide enclosure styles. 6 is supplied in the standard enclosure style and includes Vacuum contactor. Each starter includes disconnect device and TM non-reversing starter. Extensive field modification kits and factory installed modifications are available. Reversing ulletin 68 with disconnect switch, fusible and non-fusible. ulletin 6 with circuit breaker. V thermal magnetic trip breaker or 6V adjustable brip MCP. breaker. -., & s. Each includes disconnect device and TM reversing starter. Extensive field modification kits and factory installed modifications are available. Multi-Speed ulletin 68 with disconnect switch, fusible and non-fusible. ulletin 66 with Circuit reaker. 6V MCP. breaker. -6., & enclosures. Each includes disconnect device and TM multispeed starter. They are cataloged for two-speed, single winding (consequent pole) and two speed, two winding (seperate winding) motor application. Starters for three and four speed motor applications can also be supplied. Extensive field modification kits and factory installed modifications are available. 8

11 General Information Control - TM Disconnect Device Disconnect switches are heavy duty, visible blade type with positive drive action and meet industrial with stand requirements. Above amp., a non-automatic circuit breaker with fuse clips is provided. Mounting plates include drilling for field conversion of fuse size and spacing. Circuit breaker type starters use motor circuit protectors with a single, seven-point trip adjustment and manual trip feature. An optional current limiter attachment provides, amp. rms symmetrical interrupting capacity. Door Swing The concealed hinge design allows o door swing for interior accessibility. Uniform One enclosure covers, &, for each enclosure style. s & are covered by a single enclosure., & enclosure designs are each the same basic size, for each enclosure style. All this for flexibility, ease of layout and ease of installation. Grounding A UL recommended type, green head screw is provided for grounding the enclosure. A green ground wire is installed in the non-fused leg of control transformers. Door Gasketing Standard on & and optional on. Gasketing is neoprene, extruded, closed cell type for increased life, sealing qualities and safety for the installer. Combination Starters & Contactors Disconnect Operator Flange mounted operating handle provides positive control of the disconnect. Interlocking prevents opening the door with the disconnect "ON" or turning the disconnect "ON" with the door open. Interlock defeaters are provided for maintance. The position of disconnect is clearly visible to determine if controller is "ON" or "OFF". A red handle flag is visible in the "ON" state. Padlocking Operating handles can be padlocked in "OFF", with up to /8" shackle locks. Doors can be locked closed with one /8" shackle lock, thus providing security to equipment and safety to personnel. White Mounting Plate aked ANSI safety white enamel is used for the mounting plate. This provides increased visibility for safety. Add-On Accessories Most TM starter add-on accessories can be installed in combination starters. Mounting plates are pre-drilled for field installation of additional control devices. Quality Construction Painted surfaces are baked enamel for long life. All unpainted hardware is plated for corrosion resistance. Hinge pins are stainless steel. enclosures are # stainless steel for appearance and corrosion resistance. 8 Safety & Relibility Flange mounted disconnect handle. Disconnect state clearly visible. Defined enclosure grounding method. Padlocking for both door and disconnect handle. Door swing for maximum interior accessories. All contribute to safety for the installer and for operating personnel. Quality enclosure construction. Careful selection of disonnect devices and the basic TM starter all contribute to long, reliable performance. Space Savings Uniform enclosure sizes allow mixing starter sizes in a row. Mount enclosures side-by-side, without restricted door swing. Add most modifications without changing the enclosure. Select an enclosure style for max. utilzation of available space. Minimize additional control enclosures by using the space in an extra-wide starter enclosure. Space saving economy is built into TM combination starters.

12 TM - Control General Information Choice of Style Choose from three enclosure styles, standard, compact or extra-wide for non-reversing starters through. The compact style fits in low height areas and the extra-wide has approximatley square inches inches of added panel space for mounting of auxiliary equipment. & non-reversing starters are available in standard and extra-wide. Choice of enclosure style provides maximum flexibility. Versatility Choose an enclosure style to meet the application. Check the enclosure sizes to simplify your starter layouts. Check the interchangeability of mounting plates. Choose add-on accessories for the basic TM starter. Select from a wide range of factory modifications and field modification kits. All of this to improve application flexibility with minimum inventory requirements. This is the versatility of TM combination starters. Pilot Devices A complete selection of field modification kits or factory installed operator devices are available. Most are arranged for mounting on the enclosure flange, eliminating the need for a flexible wire harness to the door. Control Transformer Available factory installed or as a field modification kit. All starters can accommodate a VA extra capacity transformer in every enclosure style and type. Secondary fusing standard.

13 AC Combination Starters Control - TM AC Combination Starters with Non-Fusible Disconnect Switch, 6V - ulletin 68 Standard - Vertical Maximum Motor Horsepower Rating V V 6- V 6 Extra Wide Compact - Horizontal Cont. Amps Rating Switch Rating Amps Type General Purpose Catalog No. T8AA6 - T8AA6 - T8AA6 - T8AA6 - -use extra wide- C8AA6 - C8AA6 - C8AA6 - E8AA6 - E8AA6 - E8AA6 - E8AA6 - E8AA6 - $ Price Type Watertight Catalog No. T8WA6 - T8WA6 - T8WA6 - T8WA6 - -use extra wide- Consult Factory C8WA6 - C8WA6 - C8WA6 - E8WA6 - E8WA6 - E8WA6 - E8WA6 - E8WA6 - Price $ Type Industrial - Dust-tight Catalog No. T8TA6 - T8TA6 - T8TA6 - T8TA6 - -use extra wide- C8TA6 - C8TA6 - C8TA6 - E8TA6 - E8TA6 - E8TA6 - E8TA6 - E8TA6 - Price $ Note:. Includes starter complete with N.O. contact and phase overload relay less heaters. Ordering Information Use complete catalog number. Replace the () with the suffix from the coil table. Order Heaters at $8 each. Renewal Parts - see Page Engineering Data - see Page Modifications - see Page 6 Heater Tables - see Page Dimensions - see Page Coil Volt/Hertz /6 or / -/6 or / -/6 or / -8/6 or / -6/6 or / -8/6 Suffix Discount Schedule JC

14 TM - Control AC Combination Starters AC Combination Starters with Fusible Disconnect Switch, -V - ulletin 68 Standard - Vertical 6 Maximum Motor Horsepower Rating V Compact - Horizontal Extra Wide V Starter Cont. Amp. Rating Disconnect Amp. Rating Fuse Switch Clips Type General Purpose Catalog No. T8AA - T8AA - T8AA6 - T8AA6 - T8AA - -use extra wide- C8AA - C8AA - C8AA6 - C8AA6 - E8AA - E8AA - E8AA6 - E8AA6 - E8AA - E8AA - Price $ Type Watertight Catalog No. T8WA - T8WA - T8WA6 - T8WA6 - T8WA - -use extra wide- Consult Factory C8WA - C8WA - C8WA6 - C8WA6 - E8WA - E8WA - E8WA6 - E8WA6 - E8WA - E8WA - Price $ Type Industrial - Dust-tight Catalog No. T8TA - T8TA - T8TA6 - T8TA6 - T8TA - -use extra wide- C8TA - C8TA - C8TA6 - C8TA6 - E8TA - E8TA - E8TA6 - E8TA6 - E8TA - E8TA - Price $ Note:. Includes starter complete with N.O. contact and phase overload relays less heaters.. Class R fuse clips available on request. Ordering Information Use complete catalog number. Replace the () with the suffix from the coil table. Order Heaters at $8 each. Renewal parts - see Page Engineering Data - see Page Modifications - see Page 6 Heater Tables - see Page Dimensions - see Page Coil Volt/Hertz /6 or / -/6 or / -/6 or / -8/6 or / -6/6 or / -8/6 Suffix Discount Schedule JC

15 AC Combination Starters Control - TM AC Combination Starters with Fusible Disconnect Switch, 6-V - ulletin 68 Standard - Vertical Maximum Motor Horsepower Rating 6V V Compact - Horizontal Extra Wide Starter Cont. Ampere Rating Disconnect Ampere Rating Fuse Switch Clips Type General Purpose Catalog No. T8AA6 - T8AA6 - T8AA6 - T8AA66 - T8AA6 - -use extra wide- C8AA6 - C8AA6 - C8AA6 - C8AA66 - E8AA6 - E8AA6 - E8AA6 - E8AA66 - E8AA6 - E8AA6 - Price $ Type Watertight Catalog No. T8WA6 - T8WA6 - T8WA6 - T8WA66 - T8WA6 - -use extra wide- Consult Factory C8WA6 - C8WA6 - C8WA6 - C8WA66 - E8WA6 - E8WA6 - E8WA6 - E8WA66 - E8WA6 - E8WA6 - Type Industrial - Dust-tight Price Catalog No. Price $. T8TA6 - $. 6. T8TA T8TA T8TA T8TA use extra wide C8TA6 - C8TA6 - C8TA6 - C8TA66 - E8TA6 - E8TA6 - E8TA6 - E8TA66 - E8TA6 - E8TA Note:. Includes starter complete with N.O. contact and phase overload relays less heaters.. Class R fuse clips available on request. Ordering Information Use complete catalog number Replace the () with the suffix from the coil table. Order Heaters at $8 each. Renewal Parts - see Page Engineering Data - see Page Modifications - see Page 6 Heater Tables - see Page Dimensions - see Page Coil Volt/Hertz /6 or / -/6 or / -/6 or / -8/6 or / -6/6 or / -8/6 Suffix Discount Schedule JC

16 TM - Control AC Combination Starters AC Combination Starters with Circuit reaker, -V - Thermal Magnetic Trip Standard - Vertical, ulletin 6 Maximum Motor Horsepower Rating V 6 Extra Wide V Compact - Horizontal 6 Starter Cont. Ampere Rating Circuit reaker Ampere Rating Thermal Magnetic Trip TE TED TEC TJK TE TE TED TEC Type General Purpose Type Watertight Type Industrial - Dust-tight Catalog No. Price Catalog No. Price TAA - TWA - TTA - $ 6. $ 8. TAA - TWA - TTA - $ 6. TAA - TWA - TTA TAA - TWA - TTA - TAA - TWA - TTA TAA - TWA - TTA - TAA6 - TWA6 - TTA TAA8 - TWA8 - TTA8 - TAA8 - TWA8 - TTA TAA6 - TWA6 - TTA CAA - CAA - CAA - CAA - CAA - CAA - EAA - EAA - EAA - EAA - EAA - EAA - EAA6 - EAA8 - EAA8 - EAA Consult Factory CWA - CWA - CWA - CWA - CWA - CWA - EWA - EWA - EWA - EWA - EWA - EWA - EWA6 - EWA8 - EWA8 - EWA CTA - CTA - CTA - CTA - CTA - CTA - ETA - ETA - ETA - ETA - ETA - ETA - ETA6 - ETA8 - ETA8 - ETA Note: Includes starter complete with N.O. contact and phase overload relays less heaters. Ordering Information Use complete catalog number. Replace the () with the suffix from the coil table. Order heaters at $8 each. Renewal Parts - see Page Engineering Data - see Page Modifications - see Page 6 Heater Tables - see Page Dimensions - see Page Coil Volt/Hertz /6 or / -/6 or / -/6 or / -8/6 or / -6/6 or / -8/6 Suffix Discount Schedule JC

17 AC Combination Starters Control - TM AC Combination Starters with Circuit reaker, 6V - Adjustable Magnetic Trip Standard - Vertical, ulletin 6 Maximum Motor Horsepower Rating 6/ V V V Compact - Horizontal Extra Wide Starter Cont. Ampere Rating Circuit reaker Ampere Rating Magnetic Trip Motor Circuit Protector TEC TJC TEC TEC Type General Purpose Catalog No. TAA6 - TAA6 - TAA6 - TAA6 - TAA6 - TAA6 - TAA6 - TAA6 - TAA6 - TAA66 - TAA6 - CAA6 - CAA6 - CAA6 - CAA6 - CAA6 - CAA6 - CAA6 - CAA6 - CAA6 - EAA6 - EAA6 - EAA6 - EAA6 - EAA6 - EAA6 - EAA6 - EAA6 - EAA6 - EAA66 - EAA6 - Type Watertight Price Catalog No. Price $. TWA6 - TWA6 - TWA6 - $ 66. TTA6 - TTA6 - TTA6 - $ 8. TWA6 - TTA6 - TWA6 - TTA TWA6 - TTA6 - TWA6 - TTA6 -. TWA6 - TTA6 -. TWA6 - TTA TWA66 - TWA TTA66 - TTA Consult Factory CWA6 - CWA6 - CWA6 - CWA6 - CWA6 - CWA6 - CWA6 - CWA6 - CWA6 - EWA6 - EWA6 - EWA6 - EWA6 - EWA6 - EWA6 - EWA6 - EWA6 - EWA6 - EWA66 - EWA Type Industrial - Dust-tight Catalog No. Price CTA6 - CTA6 - CTA6 - CTA6 - CTA6 - CTA6 - CTA6 - CTA6 - CTA6 - ETA6 - ETA6 - ETA6 - ETA6 - ETA6 - ETA6 - ETA6 - ETA6 - ETA6 - ETA66 - ETA Note: Includes starter complete with N.O. contact and phase overload relays less heaters. 8 Ordering Information Use complete catalog number. Replace the () with the suffix from the coil table. Order heaters at $8 each. Renewal Parts - see Page Engineering Data - see Page Modifications - see Page 6 Heater Tables - see Page Dimensions - see Page Coil Volt/Hertz /6 or / -/6 or / -/6 or / -8/6 or / -6/6 or / -8/6 Suffix Discount Schedule JC

18 TM - Control AC Combination Starters AC Combination Reversing Starters with Disconnect Switch - ulletin 68 Fusible & Volt Maximum Motor Horsepower Rating Dual Element Fuses V V Fusible 6 & Volt 6V V Starter Cont. Amps Rating Disconnect Ampere Rating Fuse Switch Clips Type General Purpose Catalog No. T8AA - T8AA - T8AA6 - T8AA6 - T8AA - T8AA - T8AA6 - T8AA6 - T8AA6 - T8AA66 - T8AA6 - T8AA6 - Price $ Type Watertight Catalog No. Price T8WA - $ 88. T8WA - 8. T8WA6 -. T8WA6-9. T8WA T8WA Consult Factory T8WA6 - T8WA6 - T8WA6 - T8WA66 - T8WA6 - T8WA6 - Consult Factory Type Industrial - Dust-tight Catalog No. T8TA - T8TA - T8TA6 - T8TA6 - T8TA - T8AA - T8TA6 - T8TA6 - T8TA6 - T8TA66 - T8TA6 - T8AA6 - Price $ Non-Fusible Maximum Motor Horsepower Rating 6/ V V V Starter Cont. Ampere Rating 8 9 Disconnect Switch Rating Type General Purpose Catalog No. Price Catalog No. T8AA6 - $ 88. T8WA6 - T8AA6-98. T8WA6-6 T8AA6-9. T8WA6 - T8AA6-9. T8WA6 - T8AA6-98. T8WA6 - Consult Factory Type Type Watertight Industrial - Dust-tight Price Catalog No. Price $ T8TA6 - T8TA6 - T8TA6 - T8TA6 - T8TA6 - $ Notes: Includes starter complete with N.O. contact, disconnect switch less fuses, and phase overload relay less heaters. Class R fuse clips are available on request. Ordering Information Use complete catalog number. Replace the () with the suffix from the coil table. Order heaters at $8 each. Renewal Parts - see Page Engineering Data - see Page For Plugging and Jogging Service - Page 8 Modifications - see Page 6 Heater Tables - see Page Dimensions - see Page 8 Coil Volt/Hertz /6 or / -/6 or / -/6 or / -8/6 or / -6/6 or / -8/6 Suffix Discount Schedule JC

19 AC Reversing Starters Control - TM AC Combination Reversing Starters with Thermal-Magnetic Trip, V - ulletin 6 Maximum Motor Horsepower Rating Starter Cont. Circuit reaker Thermal Type General Purpose Type Watertight Type Industrial - Dust-tight Ampere Ampere Magnetic V V Rating Rating Trip Catalog No. Price Catalog No. Price Catalog No. Price 8 TAA - TWA - TTA - $ 8. $ 6. 8 TAA - TWA - TTA - $ 8. TAA - TWA - TTA TE TAA - TWA - TTA - TAA - TWA - TTA TAA - TWA - TTA - 9 TAA6 - TWA6 - TTA TED TAA8 - TWA8 - TTA8 - TAA8 - TWA8 - TTA TEC TAA6 - TWA6 - TTA6-6 6 TJC Consult Factory AC Combination Reversing Starters with Motor Circuit Protector, 6V - ulletin 6 Maximum Motor Horsepower Rating 6/ V V V Starter Cont. Amps Rating Circuit reaker Ampere Rating Magnetic Trip Motor Circuit Protector TEC TJC Type General Purpose Catalog No. TAA6 - TAA6 - TAA6 - TAA6 - TAA6 - TAA6 - TAA6 - TAA6 - TAA66 - TAA66 - TAA6 - Type Watertight Consult Factory Type Industrial - Dust-tight Catalog No. Price TTA6 - Price Catalog No. Price TWA6 - $ 8. TWA6 - $ 6. TTA6 - $ 6. TWA6 - TTA6 - TWA6 - TTA6 - TWA6 - TTA TTA6 -. TWA6 - TWA6 - TTA6 - TWA6 - TTA TWA66 - TTA TWA TTA TWA6 -. TTA Note:. Includes starter with N.O. contact, circuit breaker and phase overload relays less heaters. Ordering Information Use complete catalog number. Replace the () with the suffix from the coil table. Order heaters at $8 each. Modifications - see Page 6 Engineering Data - see Page Renewal Parts - see Page Full-load Current Table - see Page Heater Tables - see Page Dimensions - see Page 8 Coil Volt/Hertz /6 or / -/6 or / -/6 or / -8/6 or / -6/6 or / -8/6 Suffix Discount Schedule JC 9

20 TM - Control AC Combination Starters Non-Fusible AC Speed Starter with Disconnect Switch,,, 6 and V Speed, Single Winding (consequent pole), ulletin 68 Maximum Motor Horsepower Rating Constant or Variable Starter Disconnect Type Torque ( Constant Continue Switch General Purpose Horsepower) 6- Ampere Ampere V V V Rating Rating Catalog No. () () ( ) () () (6) () () () () () () () ( ) () () () () Speed, Double Winding (separate winding) T8AAC6 - T8AAC6 - T8AAC6 - T8AAC6 - T8AAC6 - Price $ Type Watertight - use size - T8WAC6 - T8WAC6 - T8WAC6 - T8WAC6 - $ Type Industrial - Dust-tight Catalog No. Price - use size - Catalog No. Price Consult Factory T8TAC6 - T8TAC6 - T8TAC6 - T8TAC6 - $ () () ( ) () () (6) () () () () () () () ( ) () () () () T8AAS6 - T8AAS6 - T8AAS6 - T8AAS6 - T8AAS use size - T8WAS6 - T8WAS6 - T8WAS6 - T8WAS6 - Consult Factory use size - T8TAS6 - T8TAS6 - T8TAS6 - T8TAS Note:. Includes starter complete with one N.O. contact on each contactor and two phase overload relays less heaters. All starters are mechanically and electrically interlocked. Six (6) heaters are required, heaters for each speed. Ordering Information Use complete catalog number. Replace the () with the suffix from coil table. Order heaters at $8 each. Engineering Data - see Page Modification - see Page 6 Renewal Parts - see Page Heater Tables - see Page Dimensions - see Page 9 Coil Volt/Hertz /6 or / -/6 or / -/6 or / -8/6 or / -6/6 or / -8/6 Suffix Discount Schedule JC

21 AC Combination Starters Control - TM Fusible AC Speed Starter with Disconnect Switch, -V - ulletin 68 Speed, Single Winding (consequent pole) Maximum Motor Horsepower Rating Constant or Variable Torque ( Constant Horsepower) V V () () / Starter Continue Ampere Rating 8 Disconnect Switch Ampere Rating Type General Purpose Catalog No. T8AAC - () () T8AAC - ( ) () () () () () 9 6 T8AAC6 - T8AAC - T8AAC - (6) () Speed, Double Winding (separate winding) Price $ Type Watertight - use size - T8WAC - T8WAC6 - T8WAC - T8WAC - Type Industrial - Dust-tight Catalog No. Price - use size - Catalog No. Price Consult Factory $ 6. T8TAC - $ T8TAC6 - T8TAC - T8TAC () () ( / ) () () (6) () / () () () () () T8AAS - T8AAS - T8AAS6 - T8AAS - T8AAS use size - T8WAS - T8WAS6 - T8WAS - T8WAS - Consult Factory use size - T8TAS - T8TAS6 - T8TAS - T8TAS Note:. Includes starter complete with one N.O. contact on each contactor and two phase overload relays less heaters. All starters are mechanically and electrically interlocked. Six (6) heaters are required, heaters for each speed. Ordering Information Use complete catalog number. Replace the () with the suffix from coil table. Order heaters at $8 each. Engineering Data - see Page Modification - see Page 6 Renewal Parts - see Page Heater Tables - see Page Dimensions - see Page 9 Coil Volt/Hertz /6 or / -/6 or / -/6 or / -8/6 or / -6/6 or / -8/6 Suffix Discount Schedule JC

22 TM - Control AC Combination Starters Fusible AC Speed Starter with Disconnect Switch, 6V - ulletin 68 Speed, Single Winding (consequent pole) Maximum Motor Horsepower Rating Constant or Variable Torque ( Constant Horsepower) 6V V () ( ) () () () () () () ( ) () () () () () Starter Continue Ampere Rating Speed, Double Winding (separate winding) 8 9 Disconnect Switch Ampere Rating 6 6 General Purpose Catalog No. T8AAC6 - T8AAC6 - T8AAC6 - T8AAC66 - T8AAC6 - T8AAC6 - Price $ Watertight - use size - T8WAC6 - T8WAC6 - T8WAC66 - T8WAC6 - T8WAC6 - Industrial - Dust-tight Catalog No. Price Catalog No. Price Consult Factory - use size - $ 6. T8TAC6 - $ T8TAC66 - T8TAC6 - T8TAC6 - T8TAC () () ( ) () () () () () () () () () T8AAS6 - T8AAS6 - T8AAS66 - T8AAS6 - T8AAS6 - T8AAS use size - T8WAS6 - T8WAS6- T8WAS66 - T8WAS6 - T8WAS use size - T8TAS6 - T8TAS6 - T8TAS66 - T8TAS6 - T8TAS () () Consult Factory Note:. Includes starter complete with one N.O. contact on each contactor and two phase overload relays less heaters. All starters are mechanically and electrically interlocked. Six (6) heaters are required, heaters for each speed. Ordering Information Coil Volt/Hertz Suffix Use complete catalog number. Replace the () with the suffix from coil table. Order heaters at $8 each. Engineering Data - see Page 9 Modification - see Page Renewal Parts - see Page Heater Tables - see Page Dimensions - see Page /6 or / -/6 or / -/6 or / -8/6 or / -6/6 or / -8/ Discount Schedule JC

23 AC Combination Starters Control - TM AC Speed Starters with Magnetic Trip Circuit reaker,,, 6 and V Speed, Single Winding (consequent pole), ulletin 66 Maximum Motor Horsepower Rating Constant or Variable Torque ( Constant Horsepower) V V 6V/V ( / ) ( / ) () ( / ) ( / ) () () () ( ) () () (6) ( / ) () () ( / ) () () () () () () () () () () () () () () ( ) ( ) () () () () Starter Continuous Ampere Circuit reaker Ampere Ratings Type General Purpose Catalog No. Price T6AAC6 -. T6AAC6 - T6AAC6 - T6AAC6 - T6AAC6 - T6AAC6 - T6AAC6 - T6AAC6 - T6AAC6 - T6AAC66 - T6AAC Type Watertight Catalog No. Price - use size - - use size - - use size - T6WAC6 - T6WAC6 - T6WAC6 - T6WAC6 - T6WAC6 - T6WAC6 - T6WAC66 - T6WAC6 - Consult Factory Type Industrial - Dust-tight Catalog No. Price - use size - - use size - - use size - T6TAC6 - T6TAC6 - T6TAC6 - T6TAC6 - T6TAC6 - T6TAC6 - T6TAC66 - T6TAC Note:. Includes starter complete with N.O. contact, on each contactor, and two phase overload relays less heaters. All starters are mechanically and electrically interlocked. Six (6) heaters are required, heaters for each speed. Ordering Information Use complete catalog number. Replace the () with the suffix from coil table. Order heaters at $8 each. Engineering Data - see Page 9 Modification - see Page Renewal Parts - see Page Heater Tables - see Page Dimensions - see Page Coil Volt/Hertz /6 or / -/6 or / -/6 or / -8/6 or / -6/6 or / -8/6 Suffix Discount Schedule JC

24 TM - Control AC Combination Starters AC Speed Starters with Magnetic Trip Circuit reaker,,, 6 and V Speed, Double Winding (Separate Winding), ulletin 66 Maximum Motor Horsepower Rating Constant or Variable Torque ( Constant Horsepower) V V 6V/V ( / ) ( / ) () ( / ) ( / ) () () () ( ) () () (6) ( / ) () () ( / ) () () () () () () () () () () () () () () ( ) ( ) () () () () Starter Continuous Ampere Rating Circuit reaker Ampere Ratings Type General Purpose Catalog No. Price T6AAS6 -. T6AAS6 - T6AAS6 - T6AAS6 - T6AAS6 - T6AAS6 - T6AAS6 - T6AAS6 - T6AAS6 - T6AAS66 - T6AAS Type Watertight Catalog No. Price - use size - - use size - - use size - T6WAS6 - T6WAS6 - T6WAS6 - T6WAS6 - T6WAS6 - T6WAS6 - T6WAS66 - T6WAS6 - Consult Factory Type Industrial - Dust-tight Catalog No. Price - use size - - use size - - use size - T6TAS6 - T6TAS6 - T6TAS6 - T6TAS6 - T6TAS6 - T6TAS6 - T6TAS66 - T6TAS Note:. Includes starter complete with N.O. contact, on each contactor, and two phase overload relays less heaters. All starters are mechanically electrically interlocked. Six (6) heaters are required, heaters for each speed. Ordering Information Use complete catalog number.replace the () with the suffix from coil table. Order heaters at $8 each. Engineering Data - see Page Modification - see Page 6 Renewal Parts - see Page Heater Tables - see Page Dimensions - see Page 9 Coil Volt/Hertz /6 or / -/6 or / -/6 or / -8/6 or / -6/6 or / -8/6 Suffix Discount Schedule JC

25 AC Reduced Voltage Starters Control - TM Auto Transformer Starter Autotransformer Closed Transition Reduced Voltage Starting of Squirrel Cage Motors Highest Starting Torque per Ampere of Line Current Available in Type & All Disconnect Types Available Complete Line Factory Installed Modifications Two Step Part Winding Part Winding Starters Two Step Starting of Squirrel Cage Motors Lowest Cost Method of Starting Type,, & s Factory Installed Modifications Open Transition Wye Delta Starter Wye-Delta Starters Available Open or Closed Transition Inrush Current / Normal Line Starting Standard 8

26 TM - Control Reduced Voltage Starters Autotransformer Closed Transition - ulletin 68 6 Max. Motor Horsepower Rating V 6V Type General Purpose Catalog No. T8AAF - T8AAG - T8AAGE - T8AAJE - T8AAJ - T8AAME - UAAL - U8AAM - U8AAPE - U8AAQE - Price Refer to Section A Wye-Delta Starters, s - ulletin 69 Wye Delta Maximum Motor Horsepower Rating 6/ 6 6 Open Transition Catalog No. T9AATA T9AAT T9AATC T9AATA T9AAT T9AATC T9AATA T9AAT T9AATC T9AATA T9AAT T9AATC V9AATA V9AAT V9AATC General Purpose Price Consult Factory Closed Transition Catalog No. T9AACTA T9AACT T9AACTC T9AACTA T9AACT T9AACTC T9AACTA T9AACT T9AACTC T9AACTA T9AACT T9AACTC V9AACTA V9AACT V9AACTC Price Note: Maximum horsepower ratings are in accordance with Standards ICS-C:. Auto transformers are -Coil type, with voltage taps at %, 6% and 8% rated in accordance with Standards ICS-. for medium-duty starting service. Starters are supplied in floor mounted enclosures without bottom cover plate for mounting against a wall. If not mounted against a wall, a rear cover plate must be ordered. Wye-Delta Starters Overload Relay Heater Selected by dividing FLC by. and select Heaters from index. Ordering Information Use complete catalog number. Replace the () with the suffix from the Coil Table. Heaters are purchased seperately at $8 each. Modifications see Page 6 Engineering Data Page Renewal Parts Page Coil Table Volt/6Hz - -8 Line Voltage -6-6 Control Transformer -T6 -T6 6 Discount Schedule JC

27 Reduced Voltage Starters Control - TM Part Winding Starters, Two Step - ulletin 69 PW PW PW PW PW 6 PW Max. Motor Horsepower Rating or -Phase V V 6/V 6 Poles Type General Purpose Catalog No. T9AA - T9AA - T9AA - T9AA - Type Watertight Price Catalog No. $ T9WA - T9WA - T9WA - T9WA - Type Industrial Price Catalog No. $ 68. T9TA - 6. T9TA - 6. T9TA T9TA - Consult Factory Open Type U Price Catalog No. $ 88. T9U -. T9U - 8. T9U T9U - Price $ Note: Includes starter complete with two contactors, timing device and two overload relays less heaters. (6 are required) These starters are usually used with wye(star) connected motors. They may also be used for delta connected motors when the motors are so designed that neither delta winding need be open during starting. Overload Realy Heater Data Heater elements should be selected for running current in each winding. A total of 6 heater elements are required per controller. Ordering Information Use complete catalog number. Replace the () with the suffix from the coil table. Order heater elements at $8 each. Modifications see Page 6 Renewal Parts see Page Engineering Data see Page Coil Volt/Hertz /6 or / -/6 or / -/6 or / -8/6 or / -6/6 or / -8/6 Suffix Discount Schedule JC

28 TM - Control Pump Control Panels Fused Disconnect Switch, R - ulletin 68 & Volts Maximum Motor Horsepower Rating Dual Element Fuses V 6 & Volts V Dual Element Fuses 6V V Non-Time Delay Fuses V V 6 Non-Time Delay Fuses 6V 6 V Starter Continuous Ampere Rating 9 9 Disconnect Ampere Rating Fuse Switch Clips Type R Weatherproof Catalog No. K8R - K8R6 - K8R6 - K8R - K8R - K8R - K8R - K8R - VK8R69 - K8R6 - K8R66 - K8R6 - K8R66 - K8R6 - K8R6 - K8R6 - K8R6 - VK8R69 - Price $ $ Note: Includes Pump Control Panel in R weather-resistant enclosure, complete with integral circuit breaker or fusible disconnect switch less fuses, start push button. Hand-Off-Auto selector switch and phase ambient compensated overload relay less heaters. Heaters are purchased separately at $9 each. For non ambient compensated overload relay delete "J" from coil suffix. 8 Ordering Information Use complete catalog number Replace the () with the suffix from the coil table. Order Heaters at $8 each. Modifications see Page 6 Engineering Data see Page Renewal Parts see Page Coil Volt/Hertz Suffix Coil Volt/Hertz Suffix /6 or / -/6 or / -/6 or / -8/6 or / -6/6 or / -8/6-96J -6J -6J -6J -6J -86J 8/ -J -J -J -J 8 Discount Schedule JC

29 Pump Control Panels Control - TM Circuit reaker,,, 6 and V - ulletin 6 Volts Thermal Magnetic Trip Maximum Motor Horsepower Rating V V 6/V Starter Continuous Ampere Rating 9 Circuit reaker Ampere Rating Type TE TED TEC Type R Weatherproof Catalog No. KR - KR - KR - KR - KR6 - KR8 - KR8 - KR6 - Price $ Volts Adjustable Magnetic Trip M.C.P TEC TJC KR6 - KR6 - KR6 - KR6 - KR6 - KR6 - KR66 - KR6 - KR69 - KR668 - $ Note: Includes Pump Control Panel in R weather-resistant enclosure, complete with integral circuit breaker or fusible disconnect switch less fuses, start push button. Hand-Off-Auto selector switch and phase ambient compensated overload relay less heaters. Heaters are purchased separately at $9 each.. Specify HP if less than HP Ordering Information Use complete catalog number Replace the () with the suffix from the coil table. Order Heaters at $8 each. Modifications see Page 6 Engineering Data see Page Replacement Parts see Page Coil Volt/Hertz /6 or / -/6 or / -/6 or / -8/6 or / -6/6 or / -8/6 Suffix -96J -6J -6J -6J -6J -86J Discount Schedule JC 9

30 TM - Control Factory Modifications For K8 & K Pump Panels Pump Panel Control Description Control Transformers Standard Capacity Primary Volts/Hertz: -/6. or / -8/6. or / -6/6. or / -8/6 8/ Watts Extra -/6. or / -8/6. or / -6/6. or / -8/6 8/ Add For Catalog Number Suffix T6J T6J T6J T86J TJ TJ TJ C6J C6J C6J C86J CJ CJ Description Control Circuit Pilot Light, Standard Transformer Type, Red Lens Fused Control Circuit (includes Fuses) Power Circuit Line Terminal oard, For only. / Aluminum Wire Grounded Service Conductor Service Entrance Lug For: - Additional Price $ 8 6 C D 8 E 6 Relays Time Delay Relay (Pneumatic). Seconds to Minutes ackspin (Includes Starter Interlock) $68 F Sequential Start timer 96 G Lockout Control Relay Substitute Non-Ambient Compensated Overload Relay 6 H Specify As Cat# Suffix Remove J (Deduct) From Suffix ORDERING EXAMPLE K8R6 with /86 Hz. Std. Transformer, Pilot Light (Options""), Grounded Service Entrance Lug for size (Option "E"), ackspin, Timer (Option "F") and Lockout Relay (Option "H"). Catalog # is K8R6 - T6J--E-F-H List Price is $ Total Price $96. Field Modifications Kits For Pump Panels Catalog Description Number Price Control Circuit Control Transformers -/6 hz. VA Capacity: 8V - KTR6-6 $6. (Primary) V & 8V KTR6-6V KTR6- V Capacity: 8V - KTR6-6. (Primary) V & 8V KTR6-6V KTR6- VA Capacity: 8V KTR6-. (Primary) V & 8V - KTR6-6V KTR6- Pilot Lights With Red Lens V A6-8A-. V - A6-8A- 8V A6-8A- 6V A6-8A- Fuse lock, Pole, A, V, - A6-9A. Class H, With Two A Dual Element Fuses Notes:. To complete Cat. No. of relay, add coil suffix from Suffix Table Coil Suffix Table Volts Hertz Suffix Catalog Description Number Price Power Circuit Line Terminal oard For A6-A $. Only, / Aluminum Wire Grounded Service Conductor - A6-A. Service Entrance Lug A6-A 6. - A6-A 8. Load Terminals For A6-A- 6. Aluminum Wire A6-A- 86. Mounting Feet - A6-A-. - A6-A-. Relays Time Delay Relay (Pneumatic), - UPDE 8.. Seconds To Minutes: Plus KTM- 6. ackspin Sequential Start - UP 6. Lockout Control Relay - SR 68. Discount Schedule JC8 Ambient Compensated KTMA-. Overload Relay KTMA- 8. KTMA- 8. KTMA- 8. Discount Schedule JC

31 Thermal Overload Relays Controls - TM Free Standing Panel Mount Price & Catalog Numbers ulletin Overload Normally Closed Normally Open & Normally Relay Contacts Closed Contacts Catalog No. Price Catalog No. Price Standard imetallic Overload Relays -AMP KTM- $8. KTM- $ 6. -AMP KTM- 6. KTM-. Ambient Compensated imetallic Overload Relays -AMP KTMA-. KTMA- 8. -AMP KTMA- 8. KTMA- 8.. Includes - Phase Overload Relay complete, less heaters. Heaters may be purchased at $8. each. See page. Single Phase Application A three phase overload relay is used for single phase applications. Only one heater is required and is to be installed in the center phase cavity of the relay. Heater Selection Select heaters based on motor namplate fullload current. Tables are for continuous rated motors. Full-load current for a given horsepower motor will vary from one manufacturer to another and will depend on RPM of motor. Type Of Protection Heaters selected directly from the table provide a maximum of % protection at o C degree ambient, is suitable for motors with a. service factor with a o C degree rise or less and with motor and controller at the same temperature. For motors with a. service factor or with a temperature rise greater then o C degree without service factor rating, use one size smaller heaters than in table. The ultimate trip of the heater is approximately % of the minimum current shown in the tables in a o C degree ambient. Ambient Correction Not necessary when overload relay is ambient compensated as identified by green reset rod. For control at an ambient constantly less than the motor ambient, correct by decreasing the nameplate motor full-load curent by % per o C difference in ambient in ambient for heater selection. For control at an ambient constantly greater than the motor ambient, correct by increasing the nameplate motor full-load current by % per o C difference in ambient. ranch Circuit Protection ranch circuit protection should be provided per National Electric Code (USA) or the Canadian Standards Asociation rules. Automatic Reset Automatic reset operation should not be used with two-wire control. Overload Adjustment These overload relays are manufactured with an exclusive calibration process to assure the ultimate in tripping accuracy and repeatability. The overload allows a true + % adjustment as a result of the process and is well suited for use with unity service factor motors requiring a shorter locked rotor tripping time. The + % adjustment is easliy made by means of a small dial on the bottom of the relay. A quick field modification also permits removal of the adjustment feature. Discount Schedule JC

32 TM - Controls Free Standing Panel Mounted s & -Type TM imetallic Standard and Ambient Compensated Thermal Overload Relays Motor Ampere Rating $8. List Each Single Phase Three Phase Heater One Heater Heaters Overload Catalog Relay Number Min. Max. Min. Max ulletin Type TM imetallic Overload Relay & Ampere, Panel Mounting O/L With N.C. Contact O/L With N.C. And N.O. Contacts Overload Relay Contact Ratings-Type TM Continuous A-C Inductive (.pf) Contact Volts,AC Amperes Make reak V or less A.A N.C. -6 V 8VA 8VA -6 V or less. A.A N.O. -6V 6 VA 6 VA Discount Schedule JC6

33 Overload Heater Data Controls - TM Type of Protection Heaters selected directly from the table provide a maximum of % protection at o C degree ambient, is suitable for motors with a. service factor with a o C degree rise or less and with motor and controller at the same temperature. For motors with a. service factor or with a temperature rise greater then o C degree without service factor rating, use one size smaller heaters than in table. The ultimate trip of the heater is approximately % of the minimum current shown in the tables in a o C degree ambient. Single Phase -,,, P, $8. List each Motor Ampere Rating - Type TM, HP Open Starter imetallic Relay Heater Catalog Number Min. Max. Min. Max Ambient Correction Not necessary when overload relay is ambient compensated as identified by green reset rod. For control at an ambient constantly less than the motor ambient, correct by decreasing the namplate motor full-load curent by % per o C degree difference in ambient. For control at an ambient constantly greater than the motor ambient, correct by increasing the nameplate motor full-load current by % per o C degree difference in ambient. Enclosed Starter Non-Ambient and Open or Enclosed Starters Ambient Compensated Relay Open Starter imetallic Relay Min Max Automatic Reset Automatic reset operation should not be used with two-wire control. Heater Selection Select heaters based on motor nameplate full-load current. Tables are for continuous rated motors. Full-load current for a given horsepower motor will vary from one manufacturer to another and will depend on RPM of motor. Three Phase -,,, P, $8. List each Motor Ampere Rating - Type TM, HP Heater Catalog Number Enclosed Starter Non-Ambient and Open or Enclosed Starters Ambient Compensated Relay Min Max. A Discount Schedule JC6

34 TM - Controls Overload Heater Data Three Phase Starter Overload Relay Heater Table - Type TM - s & Motor Ampere Rating Open Starter imetallic Relay Min Max $8. List Each Heater Catalog Number Enclosed Starter Non-Ambient and Open or Enclosed Starters Ambient Compensated Relay Min. Max Discount Schedule JC6

35 Motor Full Load Current Data Controls - TM The full load currents listed below are "average values" for motors of several manufacturers. These "average values" are as listed in the National Electrical Code 996 and must only be used as a guide for selecting suitable branch circuit components. The rated full load current shown on the motor nameplate is likely to vary from the values listed below. The NAMEPLATE full load current should always be used in determining the rating of devices. When using a design "E" Motor Special considerations apply refer to NEC 996 tables -A & & -, page -/. FULL-LOAD MOTOR-RUNNING CURRENTS IN AMPERES CORRESPONDING TO VARIOUS A.C. HORSEPOWER RATINGS Volts Volts, 8 Volts 6 Volts Volts. KV.6 KV Single Three Single Three Single Three Single Three Single Three Three Three H.P. Phase Phase Phase Phase Phase Phase Phase Phase Phase Phase Phase Phase / / / / / / NOTES:. To obtain F.L.C. for and 8 Volt motors multiply volts values by. and. respectively.. To obtain F.L.C. for 6 and Volt motors multiply Volt values by.8 and.8 respectively.

36 TM - Control Modifications Cover Controls Overload Reset Change from External to Internal Push uttons & Selector Switches With External Reset: Hand-Off-Auto Selector Switch Start-Stop Push utton With Internal Reset: Hand-Off-Auto Selector Switch Start-Stop Push utton With External or Internal Reset: or -Position Selector Switch-SPDT Forward-Reverse-Stop Push uttons High-Low-Stop or Fast-Slow-Stop Push uttons Pilot Lights Without Electrical Interlock: Standard Transformer Type, Red Lens Push-to-Test Transformer Type, Red Lens With Electrical Interlock: Standard Transformer Type, Red Lens Push-to-Test Transformer Type, Red Lens Standard Lens Color - Green lue White Yellow Amber Clear Control Circuit Contacts Each- Extra N.O.( Contact Max N/O or N/C) Contacts Each- Extra NC. (Contact Max N/O or N/C) For ulletin Number All Except 6/ 6, 68, 6, All 6-, 68-, 6-8, 66 Type All -6 All - $ N/C 96. Type Add to Type N/C $ 6. Factory Modifications N/C $ 6. Change Letter To: O C E F C C N/C N/C + N/C N/C +6 N/C N/C + N/C N/C +8 N/C N/C +9 N/C N/C Typical Catalog Number T 8 A A 6-6 Mtd. on & operated by disconnect operator: Single Pole, Double Throw Double Pole, Double Throw 68-, 68-, Unwired Terminal lock, Use with Stranded Cu Wire, #- # AWG: Wires Maximum 6 Wires Maximum Fused Control Circuit- Fuses Included Separate Control Circuit Auxiliary Relays 68-, 68-, 68-6 Type All Type N/C N/C N/C Type: Change Letter To: Typical Catalog Number 9 Control Relay- Pole Maximum Timing Relay (Pneumatic) Compelling Relay Auto. Acceleration Relay for each higher speed Auto. Decelerating Relay for each higher speed rake Relay All 6, 68, 66, -6 $6. $9. $ T 8 A A Discount Schedule JC

37 Factory Modifications Control - TM Door Gasketing Standard & Compact Extra-Wide All s For ulletin Number Encl. Type All Add to &6 Change Cat. No. Character Indicated To: Typical Catalog Number Engraved Indentification Plate Overload Relay All,, T8AA6-6 9 Ambient Compensated Overload (Per Relay): (SPDT) N.O. & N.C. Contacts (Per Relay) Alarm Contact Omit Overload Relay (Per Relay) ( ) Deduct This $ Amount All Except All 6& All Except All 6&,, All Except All 6&,, (96.) (96.) (.)(8.)(6.) (.) Power Circuit TECL Current Limiter Attachment for TEC Motor Circuit Protectors,, AIC Max. Class J Fuse Clips, In place of Class H Class R Fuse Clips, In place of Class H 6-, ,, N/A N/C N/C N/C N/C N/C N/C 9 Control transformer Description Standard Capacity Primary Volts/Hertz: -/6, or / -8/6, or / -6/6, or / -8/6 8/ Watts Extra Primary Volts/Hertz: -/6, or / /8/6, or / -6/6, or / -8/6 8/ Fused Primary (Includes Fuses) All,, -T T6 -T6 -T T T -T -C6 -C C6 -C86 -C -C C T8AA6-T6 Ungrounded Secondary with Dual Element Fuses Special Voltage on Transformer (Not Std.) Dual Voltage Secondary N/C N/C N/C N/C N/C N/C 8 Add % to Price of Transformer 9 Notes: UL Listed for field modification. Other modifications listed factory installed.. Single or Dual (- & -8) Voltage primary with -V secondary. Standard primary voltages are -, -, -,, 8, -8 and -6. Prices included panelmounted, dual-element secondary fuse, with other side of secondary connected to cabinet ground.. Price includes extra-wide enclosure when used with any ulletin 68- starter. Discount Schedule JC

38 Control - TM Factory Modifications Factory Installed Modifications For Reduced Voltage Starters Cat. Special Suffix # Add to Enclosed Starter for: $. $68. $68. 6 (Note back & bottom cover plates are required for sizes & 6.) Disconnect Devices Add to Enclosed Starter for: Non-Fusible Disconnect Switch Combination Add to Enclosed Starter for: Fusible Disconnect Switch Combination Add to Enclosed Starter for : Molded Case Circuit reaker or MCP Combination A Clips A Clips Encl. A Clips A Clips A Clips 66. A Clips Encl. A Clips A Clips 8.. A Clips 6. A Clips Encl. A Clips A Clips Auxiliary Devices Control Relay ( pole max.) Pneumatic Timing Relay ( min. max.) Phase Voltage Monitor Relay (Phase loss, Phase reversal, & Undervoltage) Ammeter & -Current Transformer Ammeter, Switch & -Current Transformer Voltmeter Voltmeter & Switch Elasped Time Meter Wattmeter Watthour meter Convenience Recepticle Mounted on Side Cylinder Lock on Door Space Heater with N.C. Auxiliary & Encl & Encl Encl ;, & Encl , & Encl , & Encl T 8 A A J 6 8 Discount Schedule JC

39 Field Modifications Control - TM 9 Modification Kits Cover Control Description Push uttons (Momentary) Selector Switches (Maintained) Pilot Lights (Include Red Lens) Reset uttons (One Reset Per Kit) Starter, &..... Starter P & Panel Mtd. Overload Reset Plug - Pack of Start-Stop Forward-Reverse-Stop Hand-Off-Auto V V V V 8V 8V 6V V 6V V V 8V V 6V 8V V 6V V V 8V V 6V 8V V V V V 8V 6V 8V External Reset for Type, & Enclosed Standard Starters /8" -- /8" 6" -- /" 9 /6"--6 /6" For ulletin Number 6 & & , , 6-, 68-, 68-, , 6 ( Req) , 68-6 ( Req) 6-, 6 ( Req) , 68-6 ( Req) Mounting Location Cover Flange Cover Flange Cover Case Case Flange Cover Flange Cover For Type, &, &, &, &, & For - - & - & - & - & - & - - & All Cover, & - - Kit Number External Reset for #ETM-& ETM- 6 R KTM- Type R - External Reset - For use with Joslyn Clark panel mounted overload kits in, & s. Dimensions from outside surface of enclosure cover to device mounting surface must fall in the range: Case - & - & - - & KTM- KTM- KTM-8 KTM- KTM- KTM-8 KTM- KTM- KTM- KTM- KTM- KTM-8 KTM-9 KTM- KTM- KTM-9 KTM-8 KTM-9 Series A KTM- KTM- KTM- KTM- KTM- KTM- KTM-6 KTM- KTM- KTM- KTM-6 KTM- KTM- KTM- KTM-6 Same As Above Price $ KTM-8 6. KTM-6 8. Notes:. For ulletins 68, 6, 68, 6, 68, & 66, & enclosed, use mm. units.. Kits may be changed in the field from -position to -position operation. In addition to HAND-OFF-AUTO, four labels are included, marked: FORWARD-OFF-REVERSE; HIGH-OFF-LOW; TEST-LAG-HEAD; ON-OFF.. Not suitable for enclosed starters with transformer. Discount Schedule JC 9

40 TM- Control Kits For Use With ulletin No. of Open Type Devices 6 & 6, 6, & Transformer Mounting Plate ulletin No. of Open Type Devices 6 & Control Circuit Kits Accessories - & - & - ETM- ETM- & & Use with Kit No. Kit Numbers Price ulletin No. of Open Type Devices -PM Field Modification Type Type Type Stainless Steel Industrial (General Purpose) (Watertight - Dust tight) Dust tight Kit Number Price Kit Number Price Kit Number Price ETM- ETM- ETM- $. 9.. ETM- ETM- ETM- $. 9.. ETM- ETM- ETM- $ ETM- ETM- ETM ETM- - ETM ETM- - ETM Type R (Rainproof-Sleet Resistance) Use with Kit No. Kit Numbers Price ETM- KTM-8. KTM-9. ETM- ETM- ETM- KTM ETM- ETM- KTM-8 $. A - $ & ETM- KTM-. 6- ETM- & 6 & Auxiliary contacts for cavity mounting in starter and contactors. One Normally Open, Convertible One Normally Closed, Convertible For side mounting on starters and contactors Two Normally Open, Non-Convertible All Transformer Kits: Complete J Fused primary a midget single fused V secondary VA Primary Capacity Voltage Hertz ulletin No. Note: Can be used in, & enclosures that have available space. See enclosure kits to determine those with available space. Standard Capacity - VA Extra Capacity - Standard Capacity - 8 & & & 8 6 /6 ulletin No. Kit Number Price All All All (See Note at Left) - KTM- TM KTM- U KUM- - KTM- TM KTM- U KUM- - KTM- - KTM-9 - & Kit Number KTR6-6 KTR6- KTR6- KTR6- KTR6- KTR6- KTR6- KTR6- KTR6- $ Price $ Fuse lock, Pole, Amp., V, Class H, with two Amp. Dual Element Fuses , KTM-. Universal Starter Adaptor Kit. Type TM starter with an assortment of heaters, auxiliary contacts, and coils and A6-999 adaptor plate. For rush and emergency repairs; can replace most - starters All - KTM-USA 8. 9 Notes:. For use with the listed open type devices. Each kit includes external "Reset" button(s) and "Reset" plug(s), either of which may be installed in the predrilled enclosure cover. All enclosures have sufficient space to allow mounting a transformer or other equipment of similar size, unless otherwise noted.. Does not have space for transformer.. External "Reset" not included. For external "Reset", add Kit Number KTM-.. Will not fit standard enclosures.. Not applicable to - ulletin 68, 68 & 68 Discount Schedule JC

41 Field Modification Kits Power Circuit Fuse Clips - Kit includes 6 clips and mounting screws,without base for lower clips. amp. volt (incl. adaptor plates) amp. 6 volt & 6 amp. volt 6 amp. 6 volt amp. volt & 6 volt amp. & 6 volt Add series letter from catalog # on the label on the door of Series A, or C Power Pole - Auxiliary pole for side-mounting on starter or contactor. Fuse Class H H & J H & J H N.O. Type NC. Type Switch Amp. & 6 6 & Fuse Clip Lower Mounting ase - required only when converting a non-fusible starter to fusible or when changing from 6 to amp. & 6 amp. & 6V Tie Pole - Auxiliary th & th power pole, both N.O. with -terminal connection for side-mounting on starter or contactors. Power Take Off - For multiple sets of overload relays. Power Pole Insulator - Required when a power pole or tie pole is added to a device in a 6 /" wide enclosure. Accessories Cavity Cover (when auxiliary contact is not used) Adapter Plate - Used to enable replacement of competitive starters with type TM. Adjusting Knob Wedges - Package of. Used in overload adjustment knob to fix trip setting at %. ulletin No All A All 6 All Control - TM ulletin No. All 6 & Kit No. Kit No. Price - & & & & - & - & $ Kit No. Price & P & & P & & - - KTM- KTM- KTM- KTM- KTM- KTM- KTM- KTM- KTM- KTM- KTM- KTM- KTM-6 KTM If unit was purchased after //98 KTMF- KTMF-6 KTMF-66 KTMF- KTMF-6 KTMF-6 If unit was purchased before //98 KTMF- KTMF-6 KTMF-66 KTMF- KTMF-6 KTMF-6 A- A6-999 KTM- N/C 8.. Heater Rack - Designed for stocking heaters for all TM starters. Rack has compartments and will hold 9 of the # series heaters or 6 of the # series heaters or a combination there of. KTM W Dimensions Modified for Outdoor Use Joslyn Clark enclosures may be field modified for outdoor use as follows:. Watertight conduit hubs shall be used at all conduit entrances. R. Watertight conduit hubs shall be used at all conduit entrances when the conduit enters at a level higher than the lowest live part.. Drain holes of /8 inch diameter shall be added to the bottom of the enclosure. Discount Schedule JC Dimensions Figure Number Overall Dimensions - inches Height Width Depth 6 6 /8 /8 /8 /8 /8 /8 / / /8 / /6 /8 / /8 /6 / /6 / /6 / /8 /6 / /6 / /6 / /6 / /6 Starter Catalog Price & KTM- KTM- KTM- KTM- $ Kit Number ETM- ETM- ETM- ETM- ETM- ETM- ETM- ETM- ETM- ETM- ETM- ETM- ETM- ETM- ETM- Hubs for Type s

42 TM - Control Renewal Parts Description of Kit Power Contact Kit, For Pole Type TM Starter Or Contactor (Movable And Stationary Contacts & Springs) Power Contact Kit, For Pole TM Starter Or Contactor (Movable And Stationary Contacts & Springs) Power Contact Kit, Pole, For Type TM6 Starter or Contactor (Movable And Stationary Contacts & Springs) ( Required for Pole Devices) Power Contact Kit, For Type TM Normally Open Auxillary Side-mounted Power Pole on & Pole Starters And Contactors ( Kit Required Per Pole-Movable And Stationary Contacts & Springs) Power Contact Kit, For Normally Closed Type TM Auxillary Side-mounted Power Pole (Movable And Stationary Contacts & Springs) For Kit Number Price,,& KTM- $. P, KTM-. KTM- 99. KTM- 9. KTM- 86. KTM-. 6 KTM6-98. & KTM- 8. P & KTM-. KTM-. KTM-.,,P & KTM-. KTM-. KTM-. Power Contact Kit, For Type TM Auxillary Side-mounted Tie Pole (Movable And Stationary Contacts & Springs Arc Shield Cover Kit ( Required Per Power Pole) TM6 Replacement Overload Relay, Standard imetallic, Less Heaters, For Single Phase Type TM Starter. Non Ambient Compensated REQD. & KTM- $ 9. REQD. KTM-8. REQD. KTM- 69. REQD. KTM-. 6 A-9A 86.,,&P KTM- 6. Replacement Overload Relay, Non Ambient Compensated, Less Heaters, For or Phase Type TM Starter Replacement Overload Relay, Ambient Compensated, Less Heaters, For or Phase Type TM Starter Replacement Current Transformer Assembly, For Use with KTM- & KTMA- Kits Power Contact Kit, Pole Type U Starter or Contactor (Movable & Stationary Contacts & Springs) For Replacement Parts For 6 Vacuum Contactors, refer to Section A,, &P KTM-. KTM- 9. KTM-. KTM-. &6 KTM-., & KTMA-. P & KTMA-. KTMA- 6. KTMA-. &6 KTMA- 9. A KUM-. 6 Coil Part Numbers For Volts/Hertz Poles Price - - T9- T9- T9- T9- T9- T9- T9- $. - T6- T6- T6-8 T6- T6- T6-9 T6-. - T6- T6-6 T6- T6-8 T6- T6- T6-8. T Series - T6- T6- T6- T6- T6- T6- T T Series - T6- T6- T6- T6- T6-6 T6- T6-6. U Series - L L L L. 6 V Series Refer to Section A Discount Schedule JC 8

43 Dimensions Open Type, Type, & Open Type /8 / /8 / - - /8 / /8 / - /8 / /6 / - /8 / /6 / /8 / /6 / - - /6 8 /8 /6 6 /8-6 /6 8 /8 /6 6 /8-8 / / 9 6 See Section A Type Poles 6 / 9 6 / / / 9 6 / / /8 8 6 See Section A Type (with transformer) /8 9 6 / / - - /8 /8 6 / /8 8 6 See Section A Type Dimensions - inches Wide High Deep Mounting A C D E / 6 /8 - - / 6 /8 - / 6 /8 - / /8 9 /6 - / /8 9 /6-9 /8 8 6 See Section A Type (with transformer) /8 6 / /8 6 /8 6 - /8 6 /8 6 - / /8 9 /6 - / /8 9 /6-9 /8 8 6 See Section A Type / 6 /6 - - / 6 /6 - - / /8 9 /6-9 /8 8 6 See Section A Type (with transformer) /8 6 / /8 6 / / /8 9 /6-9 /8 8 6 See Section A One top mtg. keyhole on center line. Open Type Type Control - TM Enclo. - Magnetic Contactors Conduit Hub and Location Top & ottom / ottom Only / / / / / Type Type H J K /8 /8 /8 /8

44 TM - Control Open Type, Type, & Open Type Poles Dimensions - inches Wide High Deep Mounting A C D E - /8 6 /6 - - /8 6 /6 - /8 6 /6 P /8 6 /6 - /8 6 /6 /6 6 /6 - /6 /6 9 / - 6 /8 /6 9 / / 8 / 8 9 /8 6 /8 6 See Section A Type - 6 / 9 6 / / / 9 6 / / P 6 / 9 6 / /8 8 6 See Section A Type (with transformer) AC Magnetic Starters Dimensions Open Type Type Type s to - /8 9 6 / / - - /8 /8 6 / 9 P /8 /8 6 / /8 8 6 See Section A Type - / 6 /8 - - / 6 /8 P / 6 /8 - / 6 /8 - / /8 9 /6 - / /8 9 /6 9 /8 8 6 See Section A Type (with transformer) - /8 6 / /8 6 /6 6 P /8 6 /6 6 - /8 6 /6 6 - / /8 9 /6 - / /8 9 /6 9 /8 8 6 See Section A Type - / 6 /6 - - / 6 /6 P / 6 /6 - - / /8 9 /6 9 /8 8 6 See Section A Type (with transformer) - /8 6 / /8 6 /6 6 P /8 6 / / /8 9 /6 9 /8 8 6 See Section A Type Conduit Hub and Location Enclo. - Top & ottom / ottom Only / / / / / H J K /8 Note:. One top mtg. keyhole on center line. Type /8 /8 /8 9

45 TM - Control Dimensions Open Type, Type, & Open Type Poles Fig. Dimensions - inches Wide High Deep A C Mounting D E E Reversing Starters & Contactors 8 /6 / / / 6 /6 / 6-8 /6 / / / 6 /6 / 6-9 /6 / / / 6 /6 / 6 8 /6 / / / 6 /6 / 6 9 /6 / / / 6 /6 / 6 - /6 8 /8 /6 6 /8 9 /8 / 8 - /6 8 /8 /6 6 /8 9 /8 /8 9 / 6 / /8 /6 Starter Refer Factory 6 See Section A Type Contactors and Starters /8 9 6 / / - - /8 9 6 / / / /8 8 6 See Section A Type (with transformer) Contactors and Starters /8 /8 6 / / - - /8 /8 6 / / / /8 8 6 See Section A Type Contactprs and Starters /8 6 / /8 6 / / 8 /8 9 /6 / - 8 / 8 /8 9 /6 / 6 6 See Section A Type (with transformer) Contactors and Starters 8 6 / / / 8 /8 9 /6 / - 8 / 8 /8 9 /6 / 6 6 See Section A Type Contactors and Starters /8 6 / /8 6 / / /8 9 /6 9 /8 8 6 See Section A Type (with transformer) Contactors and Starters 8 6 / / / 8 / 9 /6 / 9 /8 8 6 See Section A Note:. One top mtg. keyhole on center line. Conduit Hub and Location Enclo. Top & ottom ottom Only H J K - Steel Type No Hub Provisions / / / / / / /8 /8 /8 /8

46 TM - Control Dimensions AC Non-Reversing Speed Starters Dimensions-Inches Mounting Wide High Deep Fig. A C D E E F Open type - Speed, Single Winding Open Type - 9 /6 6 /6 /6 6 /6 - /6 /6 9 / /8 9 /8 Open type - Speed, Double Winding / /6-8 /6 6 /6 /6 6 /6 - /6 /6 9 / /8 9 /8 Type - Speed, Single Winding - /8 9 6 / / /6 6 /6 / /6 / - 8 / 9 /8 9 9 /8 Type - Speed, Single Winding (with transformer) /6 Fig. - /8 /8 6 / / /8-8 / /8 Type - Speed, Double Winding - /8 9 6 / / /8-8 / /8 Type - Speed, Double Winding (with Transformer) - /8 /8 6 / / /8-8 / /8 Type - Speed, Single Winding Fig. - /8 6 /6 6 6 / /8 6 /6 6 6 / 8 / 8 /8 9 /6 / 9 /6 8 / 8 /8 9 /6 / 9 /6 Type - Speed, Single Winding (with transformer) - 6 / / / 8 /8 9 /8 / 9 /6 8 / 8 /8 9 /6 / 9 /6 Type - Speed, Single Winding - /8 6 /6 6 6 / - 8 / 8 /8 9 /6 / 9 /6 Type - Speed, Single Winding (with transformer) - 6 / / - 8 / 8 /8 9 /6 / 9 /6 Type - Speed, Double Winding Type - /8 6 /6 6 6 / - 8 / 8 /8 9 /6 / 9 /6 Type - Speed, Double Winding (with transformer) - /8 6 /6 6 6 / - 8 / 8 /8 9 /6 / 9 /6 9 Notes:. Indicates mounting hole is on the center line of enclosure.. For size refer to factory.. Type includes conduit hubs. Type -No Hub Provisions 6

47 Dimensions Control - TM Combination Starters Standard or Extra-Wide Style Compact Style Standard or Extra-Wide Style & Conduit Hub Hub Application Table Dimensions-Inches Top ottom Hub Hub & / / / / & / / & / & Compact Style & Conduit Hub s Dimensions- Inches Mounting Cabinet Wide High Deep Mounting Hole Style A C D E E F G Diameter Standard 8 /8 6 / 9 - Compact Consult Factory 6 /8 Extra-Wide /8 6 / Standard /8 8 /8 9 9 / Extra-Wide /8 8 /8 6 6 / Standard 9 /8 8 /8 6 6 / Standard 9 9 /8 8 8 /8 / /6 & s 9 Dimensions- Inches Mounting Cabinet Wide High Deep Mounting Hole Style A C D E E F G H J K L M Diameter Standard 8 /8 8 9 /6 / /6 - Compact Consult Factory /6 6 / Extra-Wide /8 8 9 /6 / /6 Standard 8 /8 6 / 9 9 /8 Extra-Wide 8 /8 6 / 6 6 /8 Standard 8 /8 / 6 6 /8 Contact factory Notes: Consult Factory. Indicates mounting hole is on the center line of the enclosure.. Hub included on Type enclosure only.. Use Extra Wide Dimension for Duplex and Irrigation Pump Panels. / / /

48 TM - Control Dimensions Combination Reversing Starters Hub Application Table Dimensions-Inches Top ottom Hub Hub & / / / / & / / & / & s Dimensions- Inches Mounting Cabinet Wide High Deep Mounting Hole Style A C D E E F G Diameter - Standard /8 6 / Standard /8 8 /8 6 6 / Standard 9 /8 8 /8 6 6 / Contact factory s Dimensions- Inches Mounting Cabinet Wide High Deep Mounting Hole Style A C D E E F G H J K L M Diameter - Standard /8 8 9 /6 / /6 /8 Standard 8 /8 6 / 6 6 /8 Standard 8 /8 / 6 6 /8 Contact factory s Dimensions- Inches Mounting Cabinet Wide High Deep Mounting Hole Style A C D E E F G Diameter - Standard /8 8 9 /6 / /6 /8 /8 Standard 8 /8 6 / 6 6 /8 Standard 8 /8 / 6 6 /8 Contact factory 8 / /

49 Dimensions Control - TM Combination Speed Hub Application Table Dimensions-Inches Top ottom Hub Hub & / / / / & / / & / & s Dimensions- Inches Mounting Cabinet Wide High Deep Mounting Hole Style A C D E E F G Diameter - Standard /8 6 / Standard /8 8 /8 6 6 / Standard 9 /8 8 /8 6 6 / Contact factory s Dimensions- Inches Mounting Cabinet Wide High Deep Mounting Hole Style A C D E E F G H J K L M Diameter - Standard /8 8 9 /6 / /6 /8 Standard 8 /8 6 / 6 6 /8 / Standard 8 /8 / 6 6 /8 / Contact factory s Dimensions- Inches Mounting Cabinet Wide High Deep Mounting Hole Style A C D E E F G Diameter - Standard /8 8 9 /6 / /6 /8 /8 Standard 8 /8 6 / 6 6 /8 Standard 8 /8 / 6 6 /8 Contact factory 9

50 TM - Controls Engineering Data Ratings - Controllers - Type TM Continuous ampere and maximum horsepower ratings are in accordance with the following Standards: Starters ICS -, ICS -F Contactors ICS -., ICS -. Power Wiring Accommodation - Type TM Provision For Ring Wire Range Pressure Tongue Lugs Load Wire Terminal Terminal Screw Line Contactor Overload Type Type Width, In. #-#6 #-#6 #-# Copper (Cu) Saddle.6 #- #-#6 #-#6 #-# Copper (Cu) Saddle.6 #- #-#6 #-#6 #-# Copper (Cu) Saddle.6 #- #-# #-# #-# Copper (Cu) ox.6 #- #8-#/ #8-#/ #8-#/ Copper (Cu) ox. /6-8 #6-MCM #6-MCM #6-MCM Copper (Cu) ox. /-8 #-MCM #-MCM #-MCM Aluminum ox. /8-Hole 6 ()#-MCM ()#-MCM ()#-MCM or Copper (Cu). /8-Hole For aluminum (Al) load wiring accommodations on -, refer to local sales office. Devices are equipped with one () lug p[er phase, except size 6. UL specifies only one () wire per lug. Control Circuit Contact & Coil Terminals - Type TM Terminal Copper Wire, Screw Type Min. - Max. -6 Pressure #8-#AWG #8- Saddle One or two stranded copper wires of same size, or differing by () gauge sizes. Coil terminal wire on TM - is # AWG maximum. Control Circuit Contact Rating - Type TM Ampere Continuous Rating - Maximum 6 Volts, AC or DC Amperes A-C Inductive (.pf) D-C Inductive Contacts Volts, AC Continuous Make reak Volts, DC Make or reak - KTM- KTM- V. V or less A A V.A - KTM- -6V 6VA 6VA (V OR LESS) (8VA) - KTM-9 6V.A -6 KTM- 6A 6A (-6V) (VA) KTM- VA VA Overload Relay Contact Ratings - Type TM Continuous A-C Inductive (.pf) Contact Volts, AC Amperes Make reak N.C. V or less A.A -6-6V. 8VA 8VA N.O V or less A.A -6V 6VA 6VA 9

51 Dimensions Controls - TM Coil urden - Type TM 6Hz. Hz. Hz. Volt - Amperes Volt - Amperes Volt - Amperes Poles Inrush Sealed Inrush Sealed Inrush Sealed has two operating coils connected in series. Values given for two coils so connected. Control Transformer s For Type TM A-C Contactors Or Starters Contactor or Transformer s- Starter Volt-Amperes, 6 Hertz No. of Standard W Extra Poles Capacity Capacity.. & - & For starter with control relay; starter coil is full voltage. Ratings Of Low-Voltage Contactors For Transformer Primaries Transformer Rating -KVA, /6 Hz. 8-Hour Rating Single Phase Three Phase of Contactor Contactor 6 or Amperes V V V V V Open Enclosed This table does not apply to transformers in resistance welding service. This table applies to contactors used with transformers having an inrush of not more than () times their full-load current, irrespective of the nature of the secondary load. Kilowatt Ratings Of Low-Voltage Transformers For Resistive-Heating Loads Other Than Infrared-Lamp Loads Per ICS.- O, -Pole Contactors O, -Pole Contactors 8-Hour Rating (Open or Closed) (Open or Closed) of Contactor Contactor Heating Load, KW Heating Load, KW Amperes V V 6V V V 6V V Open Enclosed This Table applies to contactors used to switch the load at the utilization voltage of the heatproducing elements with a duty which requires continous operation of not more than five () openings per minute.

52 TM - Controls Engineering Data For Starters 6-TM; Contactors -TM Non-Combination Wiring Diagram Front View Connection For Pilot Devices Cover Mounted Pilot Devices Connect To Coil Terminals Wire Control Remote Pilot Devices Transformer Connections Volts Connections L L Fig. H & H,H & H H H 8 H & H H H All -- Others Start-Stop Pushbutton Pilot Light Momentary Contact Pushbutton Automatic Reset Automatic reset operation should not be used with two wire control. Separate Control Remove wire "A" when it is supplied. Connect separate control lines to the "" terminal on the pilot device and the "" terminal on the starter. Coil Terminal wire to be # AWG maximum.

53 Engineering Data Controls - TM For Starters 6-TM; Contactors 6-TM Elementary Diagram Seperate Control Remove wire "A" when it is supplied Connect seperate control lines to the "" terminal on the pilot device and the "8" terminal on the starter. Coil terminal wire to be No. AWG maximum. Pushbutton Control Wiring Diagram Front View Contactors "F" & "R" Are Mechanically Interlocked When Limit Switches Are Used Omit Wires "C" and "D" and Connect Per Dotted Lines

54 TM - Controls Engineering Data For Starters 6-TM Elementary Diagram Separate Control Three Phase Two Speed Two Winding Motor Separate Winding Remove wire "A" when it is supplied Connect separate control lines to the "" terminal on the pilot device and the "8" terminal on the starter. Coil terminal wire to be No. AWG maximum. Pushbutton Control Wiring Diagram Front View Contactors "HI" and "LO" Are Mechanically Interlocked

55 Engineering Data For Starters 6-TM Elementary Diagram Controls - TM Wiring Diagram Front View Momentary Contact Pushbuttons Figure Figure Connections Of Motor And Pushbotton Terminals To Starter Terminals Motor Pushbotton A C D E F M M Figure Figure T6 T T T T T Low High Figure Figure T T T T6 T T High Low Figure Figure T T T T6 T T High Low Three Phase Two Speed One Winding Motor Connection Data Figure Constant Horsepower Figure Constant Torque Figure Variable Torque L L L Open Together Speed T T T T,T,T6 Low T6 T T T,T,T High L L L Open Together Speed T T T T,T,T6 Low T6 T T T,T,T High L L L Open Together Speed T T T T,T,T6 Low T6 T T T,T,T High

56 TM - Controls Engineering Data For Starters 68-TM, 6-TM Combination Dual voltage transformer is shipped as shown connected for higher voltage. Reconnect jumpers "J" per table for lower voltage. Voltage Connect L L H to H H H H to H 6 H to H H H All Single H H Primary Transformers 6

57 Engineering Data Controls - TM For Starters 68-TM, 6-TM Combination Automatic reset operation should not be used with two wire control When limit switches are used omit wire "C" and "D" and connect per dotted lines Connections For Flange Mounted Or Remote Pilot Devices Dual voltage transformer is shipped as shown connected for higher voltage. Reconnect jumpers "J" per table for lower voltage. Voltage Connect L L H to H H H H to H 6 H to H H H All Single H H Primary Transformers

58 TM - Controls Engineering Data Standard A-C Wiring Diagrams Two-Speed, Two Winding (Separate Winding) For Starters 68-TM, 66-TM Combination Elementary Diagram: Two Speed Two Winding Motor Wiring Diagram - Front View Contactors "HI" and "LO" are Mechanically Interlocked Common Control Separate Control When control circuit obtains power from the line side of the starter as shown, and control conductors extend beyond the enclosure, they must have overcurrent protection rated not in excess of % of the control circuit conductor ampacity. Such protection should be installed in the field if starter does not have control fuses. Remove wire "A" when it is supplied. Connect separate control lines as follows: With internally mounted fuses, connect to fuse block. Without internal fuses, an external fuse must be mounted immediately adjacent to the controller. Connect to "" terminal on pilot devices and "6" terminal on starter. 8

59 Engineering Data Controls - TM Wiring Diagrams Two-Speed, One Winding (Consequent Pole) For Starters 68-TM, 66-TM Combination Wiring Diagram - Front View Elementary Diagram Two Speed One Winding Motor Three Phase Two Speed One Winding Motor Connection Data Contactors "M" and "M" are Mechanically interlocked Connections Of Motor And Pushbutton Terminals Motor Pushbutton A C D E F M M Figure Figure T6 T T T T T Low Hi Figure Figure T T T T6 T Hi Low Figure Figure T T T T6 T T Hi Low Figure Constant Horsepower Figure Constant Torque Figure Variable Torque L L L Open Together Speed T T T T,T,T6 Low T6 T T T,T,T High L L L Open Together Speed T T T T,T,6 Low T6 T T T,T,T High L L L Open Together Speed T T T T,T,6 Low T6 T T T,T,T High Connections For Case Mounted Transformer (When Provided) Wiring Diagram (Remove Wire "A") Or Remote Pilot Devices Momentary Contact Pushbuttons Dual voltage transformer is shipped as shown connected for higher voltage. Reconnect jumpers "J" per table for lower voltage. Voltage Connect L L H to H H H H to H 6 H to H H H All Single H H Primary Transformers Accessory And Replacement Kits KTM and KTR accessories can; be used with this controller. Other replacement coil by Part No. on coils. For other renewal parts information, refer to S.. 6 TM. Auxiliary contacts "W" rated for standard duty 6 volts maximum. Contact Cat. No. N.O. KTM- N.C. KTM- 9

60 TM - Control Numbering System Contactors & Non Combination Starters Type of Starter or Contactor T - Standard unit with standard TM size - starter or contactor. V - Standard unit with standard Vacuum starter or contactor. U - Standard unit with standard TM size starter or contactor. A -Standard unit except with ambient compensated overload relays. K - Irrigation Pump Controller. Cover Control A - Reset button in cover for overloads. - Reset button and Hand-Off- Auto selector switch. C- Reset button and Start-Stop push button O- None (no reset button or controls in cover) Product Code - Starters - Rev. Starter - Rev. Contactors - Contactors 9 - Part Winding Starters Type A - W - R - T - U - R Open Type T A A - 6 Number of Poles - One Pole - Two Pole - Three Pole - Four Pole or Amp. Rating A - O - - P , PW, PW, PW, PW, PW 6, 6PW Suffix With Transformer (secondary -V with single fuse) Suffix Transformer Primary Volts & Hertz -/6 or / -8/6 or / -6/6 or / 8/6 8/ Standard Capacity - T6 - T6 - T6 - T86 - T - T - T - C6 - C6 - C6 - C86 - C - C - C OR Watt Extra Capacity Suffix W/O Transformer Coil Volts & Hertz Suffix -/6 or / -/6 or / -8/6 or / -6/6 or / 8/

61 Numbering System Type of Starter or Contactor T - V- U- A- C- E- D- SD- K- Std. unit with standard Type TM starter or contactor. Std. unit with std.type Vacuum starter or contactor. Std. unit with std. TM size starter or contactor. Standard unit except with ambient compensated overload relays. Compact Extra-Wide Duplex Pump Controller. (Include Dual Dis. Switch) Duplex Pump Controller. (Include Single Dis. Switch) Irrigation Pump Controller. Product Code 8 -Fused Starter -C/ Starter 8 -FusedRev. Starter -C/ Rev. Starter Suffix With Transformer (secondary -V with single fuse) Suffix Transformer Primary Volts & Hertz -/6 or / -8/6 or / -6/6 or / 8/6 8/ Number of Poles - Three Pole Standard Capacity - T6 - T6 - T6 - T86 - T - T - T Control - TM Watt Extra Capacity - C6 - C6 - C6 - C86 - C - C - C OR Combination Starters Suffix W/O Transformer Coil Volts & Hertz Suffix -/6 or / - 6 -/6 or / - 6-8/6 or / - 6-6/6 or / - 6 8/6-86 T 8 T A 6 - T6 9 Type A - W - R - T - R Cover Control A - Reset button in cover for overloads - Reset button and Hand-Off- Auto selector switch C- Reset button and Start-Stop push button E- Hand-off Auto Selector Switch but no reset button F- Start-Stop push button but no reset button O- None (no reset button or controls in cover) of Starter 6 Disconnect Rating Volts 8 Volts 6 Volts Fuse Clip or Circuit Trip Rating or Range Fuse Clip (Applicable only to ull & 68) - amp - amp 6-6 amp - amp - 6 amp 8-8 amp - amp - amp - amp Class J Fuse Clip - non-fused - amp - amp - amp 6-6 amp - amp - amp - amp 6 - amp - amp - 6 amp Class R Fuse Clip 9 - amp 9 - amp 96-6 amp 9-6 amp 9 - amp 98-8 amp 9 - amp Circuit reaker Trip Rating or Range (Applicable only to ull. 6- & 6) Motor Circuit Protector (Used as standard at -6V) Adjustable Trip 6V AC Max. - amp 8 - amp 9 - amp 8-6 amp 8-8 amp 8 - amp Thermal-Magnetic Trip reaker (Used as standard at 8-V) - Non-Auto - amp - amp - amp - amp - amp - amp - amp - amp - amp - amp - amp 6 - amp 6-6 amp - amp - amp 8 - amp 8-9 amp 9 - amp 9 - amp 6

62 TM - Control Numbering System Speed Starters Type of Starter or Contactor T - V - U - A - Standard unit with standard Type TM starter or contactor. Standard unit with vacuum starter or contactor. Standard unit with standard TM size starter or contactor. Standard unit except with ambient compensated overload relays. Cover Control A - Reset button in cover for overloads. - Reset button and High-Off-Low selector switch. C - Reset button and Fast-Slow -Stop push button E - High-Off-Low selector switch but no reset button F - Fast-Slow-Stop push button but no reset button O - None (no reset button in cover) Type A - S - U - W - T - (Gasketed) Open Type of Starter Motor Windings C - Consequent Pole S - Separate Windings T 6 A A C - 6 Product Code - Non Combination Speed 8 -Fused Combination Speed 6 -C/ Combination Speed Motor Output C - Constant Torque or HP V - Variable Torque HP Number of Speed - Two Speed Disconnect Rating Volts 8 Volts 6 Volts Fuse Clip or Circuit Trip Rating or Range Fuse Clip (Applicable only to ull. 68) Motor Circuit Protector (Used as standard at -6V) - amp 6-6 amp - amp - amp - amp - 6 amp 8-8 amp -non-fused Magnetic Adjustable Trip 6V AC Max. Class J Fuse Clip - amp 6-6 amp - amp Class R Fuse Clip 9 - amp 96-6 amp 9 - amp 9 - amp - amp - amp - 6 amp 9 - amp 9-6 amp 98-8 amp Circuit reaker Trip Rating or Range (Applicable only to ull. 66) - amp - amp - amp - amp - amp 6 - amp - amp 8 - amp 9 - amp 8-6 amp 8-8 amp 8 - amp Thermal-Magnetic Trip reaker (Used as standard at 8-V) - Non-Automatic - amp - amp - amp - amp - amp - amp - amp - amp - amp - amp - amp 6 - amp 6-6 amp - amp - amp 8 - amp 8-9 amp 9 - amp 9 - amp Suffix With Transformer (secondary -V with single fuse) Suffix Transformer Primary Volts & Hertz -/6 or / -8/6 or / -6/6 or / 8/6 8/ Coil Volts & Hertz -/6 or / -/6 or / -8/6 or / -6/6 or / 8/6 Standard Capacity - T6 - T6 - T6 - T86 - T - T - T Suffix Without Transformer Suffix Watt Extra Capacity - C6 - C6 - C6 - C86 - C - C - C 9 6

63 Numbering System Control - TM Reduced Voltage Auto Transformer Starters Type of Starter or Contactor T - V - U - A - Standard unit with standard Type TM starter or contactor. Standand unit with vacum starter or contactor. Standard unit with standard TM size starter or contactor. Standard unit except with ambient compensated overload relays. Cover Control A - Reset button in cover for overloads. - Reset button and Hand-Off-Auto selector switch. C - Reset button and Start-Stop push button O - None (no reset button in cover) Type A - U - W - T - Open Type of Starter T 8 A A M E - 6 Product Code 8- Non Combination 8- Fused Combination 8- C.. Combination Line Voltage A - - C - D - 8V/6Hz V/6Hz V/Hz 8V/Hz E - F - G - 6V/6Hz V/Hz V/6Hz Motor Horsepower A - - C - D - E - F - G - H - J - K - L - HP HP HP HP HP HP HP HP HP 6 HP HP M - HP N - HP P - HP Q - HP R - HP S - HP T - HP U - HP V - HP W - 6 HP X - Other Suffix With Transformer (secondary -V with single fuse) Transformer Primary Volts & Hertz -/6 or / -8/6 or / -6/6 or / 8/6 8/ Standard Capacity - T6 - T6 - T6 - T86 - T - T - T Suffix Watt Extra Capacity - C6 - C6 - C6 - C86 - C - C - C Suffix Without Transformer Suffix Coil Volts & Hertz -/6 or / -/6 or / -8/6 or / -6/6 or / 8/6 6

64 General Information - AC Control Application The Space Savers in s thru offer versatile and compact AC contactors for industrial motor, heating and other power circuit switching. Simplified design coupled with built-in reliability assures the user long, trouble-free operation in machine tools, process controls, air-conditioning, custom panels and other demanding applications. Description All magnetically operated contactors incorporate a modern, modular design compatible with other control component modules. Terminal location make them ideal for straight-through wiring and for wire-channel layouts. Accessible, up-front pressure-type terminals are standard. The hot molded, high arc resistant two or three piece housings not only totally enclose contacts and operating coils for environmental protection; but also separate them as added protection against internal phase-to-phase short circuits. Generous size, long wearing double break contacts are furnished on all sizes. Contacts are made of silver cadmium oxide for "anti-weld" protection under high inrushes. Contacts do not require adjustment or periodic dressing (filing). Coil Data Standard coils for continuous duty service are equipped with pressure type terminals. Molded coil constrution resists moisture; thermal and mechanical stress. Typical User enefits: Modern Modular Design - makes contactors compatible with other control panel components. Ideal for wire-channel layouts. Compact - Contactors conserve control panel area without sacrificing accessibility or reliability. The amp. contactors occupy less than 9. sq. in. of panel space. Only asic Parts - This simple design affords longer operating life and greater reliability than more complex units. Fast Installation - Accessible up-front pressure type terminals on both power and control circuits, take unlugged stripped wire. Design permits straight-through wiring. Quick, Easy Inspection - Simply withdraw the front housing piece, after removing two screws, all main contacts are in full view. No need to disturb wiring or remove contactor from panel for complete inspection of all parts.. Three piece molded housing.. Arc barriers. 8. Stainless steel springs.. Double reak silver cadmium oxide contacts.. Side mounted auxiliaries. 6. Free-floating armature-magnet frame.. Molded continuous duty coil.. Three piece molded housing.. Pressure type terminals. 6

65 AC Control - Non-Reversing Contactors Pole Contactors -Three Phase 8-Hour Rating in Amperes Open Enclosed Open Type Catalog No. 9A- A- A- A- A Contactor comes standard with N.O. auxilary. Price $ Auxiliary Contact Rating AC Volts Auxiliary Contacts (Interlocks), &,,, s - Amperes Continuous 6.. Max. No. of N.O. or N.C. or N.O. - N.C. Auxiliary units Inrush 6 Ratings - Ampere and Horsepower, Single Speed Motors Amperes Three Phase - Horsepower Rating Plug-Stop or Starting Jogging Duty Open Enclosed V V 8/V V V 8/V / 6 Single Phase - Horsepower Rating Plug-Stop or Starting Jogging Duty V V V V / Notes:. These ratings are based on locked rotor current not exceeding six times motor full load current for the max. horsepower rating. Ordering Information Use complete catalog number. Replace the () with the suffix from the coil table. Modification Page Coil Table DC Voltage - incl. - incl. 8 - incl. - incl. For all DC Coils up to add $9 & add $8 Suffix 8 - incl.,,,,,,,, - incl. - incl. 6Hz/Voltage Suffix 9 Discount Schedule JC 6