Property of American Airlines
|
|
- August Moore
- 5 years ago
- Views:
Transcription
1 MAINTENANCE LIFT Specifications/Shipping/Storage Manufactured by TISl:D TE co EQUIPMENT LLC Coral Springs, Florida
2 Section 3: Specifications 1. DIMENSIONS & WEIGHT Length 398 in (10.11 m) Width 103 in (2.62 m) Height (Hi-Lift Down)* 116 in (2.95 m) Weight 25,950 Lbs (11,771 kg)) Minimum Platform Floor Height - Stabilizer Set 74 in (1.88 m) Maximum Platform Floor Height - Stabilizer Set* 384 in (9.75 m) 2. CAPACITY Maximum Payload (Scissors Lift) 4000 lb ( kg) Maximum Payload (While Driving)* 4000 lb ( kg) Hydraulic Fluid Reservoir 50 US gal (227.1 l) 3. PERFORMANCE Hi-lift Raise Speed.40 fps (12.2 cm/s) Hi-lift Lowering Speed.28 fps-.23 fps (8.5 cm/s-7 cm/s) Hydraulic System Relief Pressure 1,800 psi (12411 kpa) NOTE: The hi-lift raising speed may vary due to P.T.O. and engine speed. NOTE: The hi-lift lowering speed noted is pre-set by Tesco. The hi-lift lowering speed can be faster or slower by opening or closing the adjustable flow control valve. * Dependent on chassis selected and optional equipment fitted 4. MAJOR COMPONENTS A. Chassis Please refer to the chassis manufacturer s manual. B. Maintenance Platform Platfrom Length 252 in (6.4 m) Platfrom Width (Min. Side Ext. Stowed) 96 in (2.44 m) Platfrom Width (Max. Side Ext. Deployed)) 144 in (3.66 m) SPECIFICATIONS Page 1 Mar. 17
3 Platform Off Center Max. Load Capacity 1000 lb (453.5 kg) C. Hi-Lift Single Acting Cylinder Lower Cylinder Set 2 Lower Cylinder Set Stroke 92 in (2337 mm) 1 st Stage Bore Diameter 6 in (152 mm) 2 nd Stage Bore Diameter 5 in (127 mm) 3 rd Stage Bore Diameter 4 in (102 mm) Fluid Capacity Retracted 3.3 US gal (12.5 l) Fluid Capacity Extended 8 US gal (30 l) Upper Cylinder Set 2 Upper Cylinder Set Stroke 80 in (2032 mm) 1 st Stage Bore Diameter 6 in (152 mm) 2 nd Stage Bore Diameter 5 in (127 mm) 3 rd Stage Bore Diameter 4 in (102 mm) Fluid Capacity Retracted 2.9 US gal (10.9 l) Fluid Capacity Extended 7 US gal (26.5 l) D. Stabilizer Dimensions & Capabilities Stowed Dimension (Pad to Pad) 96 in (2438 mm) E. Stabilizer Double Acting Rod Cylinder Specifications Cylinder Bore Diameter 2.5 in. (63.5 mm) Stroke 12 in. (304.8 mm) Fluid Capacity Retracted.4 qt (.38 l) Fluid Capacity Extended 1.1 qt (1.02 l) F. Hydraulic System Hydraulic Pump Gear Type Pump Flow Rating at 1200 RPM s 19 gpm (71.9L/m) Page 2 Apr. 17
4 G. Electrical System Servo Control Valve Solenoids 12 VDC negative ground Master Control Valve Solenoid 12 VDC negative ground Circuit Solenoid Switch & Relays 12 VDC negative ground Electrical Circuit Protection Thermal circuit breaker SPECIFICATIONS Page 3 June 07
5 252 in (6.41 m) 42 in (1.07 m) 156 in (3.96 m) in (5.72 m) 398 in (10.11 m) RIGHT SIDE VIEW TRAVERSE 120 in (3.05 m) 384 in (9.75 m) - MAX. FLOOR HT. STAB. SET* 74 in (1.88 m) - MIN. FLOOR HT. STAB. SET * * DEPENDENT ON CHASSIS SELECTED AND OPTIONAL EQUIPMENT FITTED. Figure 1 DIMENSIONS - ML50-30 LIFT TYPICAL - RIGHT SIDE VIEW Page 4 Mar. 17
6 103 in (2.62 m) 144 in (3.66 m) 74 in (1.88 m) - MIN. FLOOR HT. STAB. SET * 116 in * (2.95 m) HI-LIFT DOWN * DEPENDENT ON CHASSIS SELECTED AND OPTIONAL EQUIPMENT FITTED. Figure 2 DIMENSIONS - ML50-30 LIFT - REAR VIEW SPECIFICATIONS Page 5 Apr. 17
7 PLATFORM EXTENSION - (OPTIONAL BOTH SIDES SHOWN) Figure 3 DIMENSIONS - ML50-30 LIFT TYPICAL - PLATFORM PLAN VIEW Page 6 June 07
8 Section 4: Shipping 1. GENERAL INFORMATION This section contains general information on preparing the hi-lift unit for transportation domestically and overseas. Check regulations of the states and/or countries through which the hi-lift unit will be transported for specific requirements. Review storage requirements (Section 5) for information on protection that may be required if time en route is expected to be more than two or three days. 2. DOMESTIC SHIPMENT There are few special preparations needed to ship the unit domestically. 1. Ensure all stabilizers are fully retracted to stowed position. 2. Ensure the work platform is fully lowered and resting firmly in the stowed position on the rest pads. 3. Ensure the folding handrails (optional) are locked in the raised position or the chain post guardrails are in raised position. 4. Restrain the hi-lift unit with universal tie-down straps, chains and over-center tensioning devices. NOTE: Refer to the chassis manufacturer s manual for any preparations the chassis may need before shipping. 3. OVERSEAS SHIPMENT CAUTION DO NOT SHIP THE UNIT ABOVE DECK WHERE IT CAN BE EXPOSED TO SALT WATER. 1. Ensure all stabilizers are fully retracted to stowed position, and the work platform is fully lowered. The folding handrails (optional) are to be locked in the raised position or the chain post guardrails are in raised position. 2. Restrain the hi-lift unit with universal tie-down straps, chains, and over-center tensioning devices, and chocks. Inspect all attaching points to ensure that the restraints are secure and that straps (if used) do not bear against angular surfaces that may cause failure en route due to chafing or vibration. 3. Check for any loose items. If necessary, pack the items separately and place in a secure location. SHIPPING 1-4 Page 1 Apr. 05
9 THIS PAGE INTENTIONALLY LEFT BLANK
10 Section 5: Storage 1. SHORT-TERM STORAGE ONE MONTH MAXIMUM 1. Perform all periodic maintenance services as prescribed in Chapter Chock drive wheels front and rear to prevent movement in any direction. 3. Disconnect and remove the 12-volt battery and store in cool, dry location. 4. Coat all exposed unpainted metal surfaces with rust preventative. Especially important are exposed hydraulic cylinder rods. 2. LONG-TERM STORAGE 1. The unit should be stored in a shelter to protect it. If a shelter is not available, cover it with tarpaulins or other protective material. Instrument panels should be covered and taped to provide a moisture-proof seal. 2. Perform all periodic maintenance services as prescribed in Chapter Raise and block chassis so that all wheels are off ground. 4. Disconnect and remove the 12-volt battery and store in cool, dry location. 5. Coat all exposed unpainted metal surfaces with rust preventative. Especially important are exposed hydraulic cylinder rods. NOTE: Refer to the chassis manufacturer s manual for procedures to be performed for chassis preservation for both short-term and long-term storage. STORAGE 1-5 Page 1 Apr. 05
11 THIS PAGE INTENTIONALLY LEFT BLANK
Property of American Airlines
Section 2: Operation 1. GENERAL INFORMATION Safety First! is the motto at Tesco; therefore, the first part of the Operation section begins with safety features and procedures. Operation of the Tesco CL80-20
More informationWARNING TABLE 3-1: DAILY SAFETY CHECK
III. T PSL-10 MAINTENANCE his chapter contains maintenance information for the Ricon PSL-10. The information consists of a maintenance schedule, component descriptions, electrical diagrams, fuse locations,
More informationM SEPTEMBER 2017
M-17-33 SEPTEMBER 2017 To fi nd maintenance & parts information for your TE-15 or TE-20 Liftgate, go to www. maxonlift.com. Click the PRODUCTS, TUK-A-WAY and TE-15/TE-20 buttons. Open the Maintenance Manual
More informationInstallation Instructions for Model CityFix
INTERLIFT Interlift, Inc. 15939 Piuma Ave. Cerritos, CA 90703 Tel: 888-774-5844 Fax: 562-924-8318 Installation Instructions for Model CityFix www.interlift.net 1. LIFT LOCATION The installation surface
More informationINSULATED TELESCOPING AERIAL DEVICE SPECIFICATIONS Van Mounted 31July2002
INSULATED TELESCOPING AERIAL DEVICE SPECIFICATIONS Van Mounted 31July2002 It is the intent of the following specifications to set minimum requirements for an INSULATED 29 foot bottom of platform, 34 foot
More informationM REV B SEPTEMBER 2017
M-16-33 REV B SEPTEMBER 2017 To fi nd maintenance & parts information for your TE-25 or TE-30 Liftgate, go to www. maxonlift.com. Click the PRODUCTS, TUK-A-WAY and TE-25/TE-30 buttons. Open the Maintenance
More information2016 Product Application Guide NCL2 CENTURY SERIES
2016 Product Application Guide 6-22-16 NCL2 CENTURY SERIES NCL2 Century Series Features Fully automatic NHTSA compliant lift, operated by an attendant Loading position - either direction Interfaces with
More informationAUTOMATIC LEVELING SYSTEM OPERATION & MAINTENANCE
WARNING For maximum stability during use of the PowerPlus Leveling Systems, all levelers and wheels must be in contact with the ground. NEVER use levelers to change tires or to perform under chassis work
More informationCRYSTEEL S. this manual must be included with the vehicle after completing the installation.
Website: www.tbei.com E-mail: sales@tbei.com CRYSTEEL S POWER TAILGATE this manual must be included with the vehicle after completing the installation. Web Site E-Mail Phone (507) 726-2728 www.crysteel.com
More informationBAYLIFT MODEL AND KIT NUMBERS
-PRINT- MARCH 2014 - TABLE OF CONTENTS- SPARE PARTS IV. SPARE PARTS T his chapter contains parts illustrations and lists for the Ricon BayLift Public use wheelchair lift. Each exploded view of a major
More informationCX17BCOMPACT EXCAVATOR
CX17BCOMPACT EXCAVATOR ENGINE Model Mitsubishi L3E-W231KBS Cylinders 3 Bore/Stroke Displacement Fuel injection Fuel injection pump Fuel Fuel filter Cooling 2.99 in x 2.76 in (76 x 70 mm) 58.1 in 3 (952
More informationInspections of Aerial Equipment
I Inspections of Aerial Equipment Milton J. Luttrell, III Aspen Aerials, Inc. nspections of aerial equipment are a requirement as set forth by the American Nations Standards Institute (ANSI). Owners of
More informationG3 UHT TRANSMISSION. G3 UHT Transmission Replacement. G3 UHT Transmission Removal
G3 UHT Transmission Replacement The following procedures cover replacing the left hand UHT Transmission. The same procedures can be followed to remove the right hand UHT Transmission. 5. Raise the seat
More informationX X26 Serial Numbers
X 26-32 X26 Serial Numbers 50906 53100 ENGLISH When contacting Upright for service or parts information, be sure to include the MODEL and SERIAL NUMBERS from the equipment nameplate. Should the nameplate
More informationS-SERIES AND K-SERIES SERVICE MANUAL
-PRINT- S-SERIES AND K-SERIES - TABLE OF CONTENTS- MAY 2014 INSTALLATION II. INSTALLATION T his chapter contains instructions for installing the RICON S-Series and K-Series Public Use wheelchair lift into
More information15 Ton Fixed Height Shoring Jack Model 706A
The Malabar Fixed Height Shoring Jack is an 18 ton capacity single stage hydraulic jack designed primarily for use in aircraft maintenance. The jack features a spring centered cylinder assembly that pivots
More informationJ1 Plug Pin Identification
D D8 D D D D ART_8 J 8 D D0 R R R R TB 80 D D D D D D J Plug Pin Identification PIN # WIRE # SIGNAL FUNCTION 0 INPUT Drive Reverse INPUT Drive Forward OUTPUT Brake, Decel Valve signal 8 INPUT Steer Left
More informationLIFT N LOAD INSTALLATION, MAINTENANCE, & SAFETY INSTRUCTIONS (800)
LIFT N LOAD INSTALLATION, MAINTENANCE, & SAFETY INSTRUCTIONS (800) 272-6276 001-321-757-7611 www.cramarotarps.com Plants In: Delaware, Florida, Massachusetts, Nevada, Ohio, and Canada General Information
More informationQuick Install Lift AL065 Installation Guide & Owners Manual
Quick Install Lift AL065 Installation Guide & Owners Manual Congratulations on your new lift purchase. The Quick Install Lift line is one of the easiest and most trouble free ways to transport your scooter
More informationJ1 Plug Pin Identification
D5 D8 D7 D4 D5 D ART_8 J 4 8 D D0 7 R R R R4 TB 80 D D D D4 D D J Plug Pin Identification PIN # WIRE # SIGNAL FUNCTION 0 INPUT Drive Reverse INPUT Drive Forward OUTPUT Brake, Decel Valve signal 4 8 INPUT
More informationManufacturers of Patented Truck Trailering Lifts 16 W. West Hill Road Barkhamsted, CT 06063. Ph. 860-379-7772 or 1-800-450-8659 Fax 860-738-2777 WWW.TRUHITCH.COM INFO@TRUHITCH.COM 1 Read All Instructions
More information3.2 UTLI41A AND UTLI46A GENERAL SPECIFICATIONS
3.2 UTLI41A AND UTLI46A GENERAL SPECIFICATIONS The UTEM SkyTel UTLI41A or UTLI46A is an insulated telescoping aerial lift available with either a side mounted single man platform or an end mounted single
More informationKEY. Hook block. Operator aids. Distance from hook to head sheave pin. Cab. Hook and ball. Heating / Air conditioning. Hydraulics.
KEY /////////////////////////////////////////////////////////////////////////////////////////////////////////////// Operator aids Hook block Cab Distance from hook to head sheave pin Heating / Air conditioning
More informationCM170 TELESCOPIC CRANE CONTENTS ///////////////////////////////////////////////////////////////////////////////////////// Crane Features...4 Boom Diagram...5 Load Chart: Main Boom & Jib...6 LMI Codes...7
More informationbefore serial number 2214
before serial number 2214 Contents Page Safety Rules... 3 Pre-operational & Safety Inspection... 4 Operating Instructions... 6 Transport... 12 Maintenance & Routine Service... 12 Specifications... 14 SAFETY
More informationJ1 Plug Pin Identification
D5 D D D D5 D ART_ J D D0 R R R R TB 0 D D D D D D J Plug Pin Identification PIN # WIRE # SIGNAL FUNCTION 0 INPUT Drive Reverse INPUT Drive Forward OUTPUT Brake, Decel Valve signal INPUT Steer Left 5 OUTPUT
More informationWARNING. The X32 Machine has been re-assessed to ensure compliance to the Machinery Directive (2006/42/EC). The Machine rating has been changed from:
WARNING The X32 Machine has been re-assessed to ensure compliance to the Machinery Directive (2006/42/EC). The Machine rating has been changed from: Windspeed rating of 12.5 m/s (Beaufort 6) To Windspeed
More informationPyrolance, LLC PTO-HYDRAULIC DRIVEN ULTRA HIGH PRESSURE FIRE FIGHTING SYSTEM B 2000 M-P
== B-2000 M-P, PTO, Manual - 2013.002 11/26/13 == SPECIFICATIONS FOR PTO-HYDRAULIC DRIVEN ULTRA HIGH PRESSURE FIRE FIGHTING SYSTEM B 2000 M-P 1 SPECIFICATIONS FOR FIRE FIGHTING SYSTEM HIGH PRESSURE FIRE
More informationINSTALLATION MANUAL DMD-22 & DMD-33
M-12-20 REV. E JULY 2016 INSTALLATION MANUAL DMD-22 & DMD-33 To fi nd maintenance & parts information for your DMD Liftgate, go to www.maxonlift. com. Click the PRODUCTS, RAILIFT & DMD buttons. Open the
More informationNot Included. Rear Half Harness
Basic Light Kit 60102 Caution! Wear appropriate eye protection! Disconnect the battery or batteries. Place run/tow switch in tow position before disconnecting the batteries on models using that feature.
More informationFIREWOOD PROCESSORS. WP200 Series Tractor PRODUCT FEATURES
FIREWOOD PROCESSORS WP200 Series Tractor PRODUCT FEATURES Auto Cycle Ergonomic Controls Adjustable 4-Way Wedge Adjustable Exit Chute Cylinder Cover Adjustable Log Length Guide WP240 25 24" $9,571 Split
More informationSLIDE-AWAY EXPORT USE SPARE PARTS
IV. T SLIDE-AWAY EXPORT USE SPARE PARTS - TABLE OF CONTENTS- his chapter contains parts diagrams and lists for the Ricon Slide-Away Export Use wheelchair lift. The exploded view of each major lift assembly
More informationProperty of American Airlines
MH Utility Vehicle Section 3 SECTION 3: SPECIFICATIONS AND CAPABILITIES A. DIMENSIONS 1. Length, Excluding Coupler... 153 inches (389 cm) 2. Width, Overall... 78 inches (198 cm) 3. Height, Overall... 78
More informationBAYLIFT SERVICE MANUAL
-PRINT- MARCH 2014 - TABLE OF CONTENTS- MAINTENANCE III. BAYLIFT MAINTENANCE AND REPAIR R egular maintenance of the Ricon BayLift Public Use Wheelchair lift is essential for optimum performance, and will
More information650 Series Cargo Van Lift Mounting Instructions Ford Transit (Standard Roof) 2015-Present
TOMMY GATE OWNER'S / OPERATOR'S MANUAL 650 Series 650 LB Capacity 650 Series Cargo Van Lift Mounting Instructions Ford Transit (Standard Roof) 2015-Present Installing the Base Plate 1. Examine the interior
More informationGLOSSARY OF TERMS, MAXON COLUMNLIFT (BMR)
GLOSSARY OF TERMS, MAXON COLUMNLIFT (BMR) 1. STRUCTURAL COMPONENTS: 6 Fixed Ramp A 6 Fixed Steel Ramp that attaches to the Folding Section of a two piece Platform or attaches to the Main Section of one
More informationPRODUCT CATALOGUE
PRODUCT CATALOGUE 2008 www.scorpionjacks.com.au Heavy duty, all welded, steel chassis forms the backbone of these incredibly rugged jacks. All air lines are totally protected within the boxed steel handle.
More informationHYDRAULICS. Control valves 10 spool Pilot control for left/right track travel, boom, arm, bucket & swing Manual control for breaker & backfill blade
CX47 Compact Excavator ENGINE Model... Yanmar 4TNE88-EYBC Cylinders... 4 Bore/Stroke... 3.46 x 3.54 (88 x 90 mm) Displacement... 133.5 in 3 (2180 cc) Fuel injection... Direct Fuel injection pump... Electronic
More informationSection Ton Ram. Specifications
50 Ton Ram Specifications Dixon Valve & Coupling Company 800 High Street Chestertown, MD 0 ph: 800 355 99 fax: 800 83 49 www.dixonvalve.com Item Part No. 50T003 50T04 00-0008 50T0 50T09 50T00 50T0 50T00
More informationP Original Series Cargo Van Lift Mounting Instructions Fullsize Ford Van present. Preparing the Gate
Fullsize Ford Van- 1992-present Preparing the Gate 1. Remove the mounting hardware which is banded to the liftgate. 2. Verify mounting kit (Figure 1 and Table 1). S-400-40 STRAP VAN MOUNTING EAR BENT BRACKET
More informationAUXILIARY BATTERY BOX INSTALLATION INSTRUCTIONS
AUXILIARY BATTERY BOX INSTALLATION INSTRUCTIONS The original TOMMY GATE hydraulic lift Assembling the Auxiliary Battery Box 1. Remove the cover from the auxiliary battery box by removing the two nuts and
More informationA GROVE WORLDWIDE COMPANY
A GROVE WORLDWIDE COMPANY R each work areas that were previously unreachable with the Grove Manlift MZll6D aerial work platform! Check these features: Working heights of 116 ft. (35.35m). 700 Ibs. (317kg)
More informationParts & Service Manual
Parts & Service Manual 69RT Series ART_4265 RT - Internal Combustion 3369RT Serial Number Range 13300000 - Up 4069RT Serial Number Range 13800000 - Up Part # 43444 Revision History Date Reason for Update
More information1002 Wayne Avenue Chambersburg, PA Fax: DI-100 OWNER S MANUAL. General Information Instructions Maintenance
1002 Wayne Avenue Chambersburg, PA 17201 717.261.0922 Fax: 717.264.5581 DI-100 OWNER S MANUAL General Information Instructions Maintenance TABLE OF CONTENTS Installation Instructions... 4-5 Installation
More informationT550 COMPACT TRACK LOADER SPECIFICATIONS
T550 COMPACT TRACK LOADER SPECIFICATIONS Loader Dimensions Dimensions are given for loader equipped with standard tracks and 68 in. Construction and Industrial bucket and may vary with other bucket types.
More informationTroubleshooting Guide
Troubleshooting Guide diesel - gasoline - LPG P/N 0172021 June 1999 P.O. Box 1160 St. Joseph, MO 64502-1160 1-800-255-0317 Fax: 816-360-9379 www.snorkelusa.com GENERAL INFORMATION This manual contains
More informationModel ET 5000W Operation and Service Manual
Model ET 5000W Operation and Service Manual Patented 5/16 BALL Load Capacity: 5000 lbs The ET 5000W ESCALATE TRAILER offers ground level roll-on loading and roll-off unloading of equipment with non-tilting
More informationNumber of rollers Top, each track 1 Bottom, each track 5 Number of shoes Triple grouser each side 39. Gradeability 70%
CX75 EXCAVATOR TIER III CERTIFIED ENGINE Model Isuzu AU-4LE2X,Tier III certified Type 4-stroke turbocharged Cylinders 4 Bore/Stroke 3.35 in x 3.78 in (85 x 96 mm) Displacement 133 in 3 (2179 cc) Fuel injection
More information30,000 lb. HEAVY DUTY PPF 195 POST PULLER
OPERATION, MAINTENANCE AND PARTS MANUAL 30,000 lb. HEAVY DUTY PPF 195 POST PULLER Read and understand all of the instructions and safety information in this manual before operating or servicing this piece
More informationM REV. B AUGUST 2010 INSTALLATION MANUAL GPTWR-3
M-08-36 REV. B AUGUST 2010 INSTALLATION MANUAL GPTWR-3 MAXON Lift Corp. 2010 TABLE OF CONTENTS WARNINGS... 3 SAFETY INSTRUCTIONS... 3 STANDARD LIFTGATE COMPONENTS... 4 GPTWR-3 INSTALLATION PARTS BAGS...
More informationOperations Manual for the BJ Series Genco
Operations Manual for the BJ Series Genco 7 June 2009 Second Edition Genco Mine Service 630 North 400 East Huntington, Utah 84528 Phone 1-800-662-1257 fax 1-435-687-9256 7 8 Genco Pickup Operators Manual
More informationHERCULES SIGN POST DIGGER DERRICK
Introduction UTV International has manufactured a line of tracked carriers since 1992. In 1996, we integrated our first digger derrick onto a tracked carrier. Since then we have been engaged in a continual
More informationInstallation, Maintenance and Service Manual Power Cord
Installation, Maintenance and Service Manual Power Cord 45-081, REV. 8/14 1 of 8 Table Of Contents Section 1 Installation Procedure... 3 1.1 General...3 1.2 Sheave installation...4 1.3 Anchor installation...4
More informationCONTENTS TC500 SERIES TELESCOPIC CRANE
TC500 SERIES TELESCOPIC CRANE CONTENTS /////////////////////////////////////////////////////////////////////////////////////////////////////////////// Crane Features...4 5096S Chassis Data - S Models...
More informationCORPORATION OPERATOR S MANUAL HWH TOUCH PANEL-CONTROLLED 310 SERIES LEVELING SYSTEM
HWH R CORPORATION OPERATOR S MANUAL HWH TOUCH PANEL-CONTROLLED 310 SERIES LEVELING SYSTEM FEATURING: Touch Panel Control Hydraulic Leveling Straight-Acting Jacks Suspension Air Dump HWH HYDRAULIC LEVELING
More informationMOREHOUSE INSTRUMENT COMPANY, INC. 60,000 LBS CAPACITY AIRCRAFT PART NUMBER SCALE S FORCE CALIBRATION PRESS PART NO.
INDEX 1. GENERAL SPECIFICATION AND DRAWING 804000-03... 2 2. ASSEMBLY INSTRUCTIONS... 5 3. OPERATING INSTRUCTIONS... 6 4. MAINTENANCE INSTRUCTIONS... 7 5. CERTIFICATE OF CAPACITY LOAD TEST AND OVERLOAD...
More informationONBOARD AIR SYSTEM FOR ALL VEHICLES APPLICATIONS
ONBOARD SYSTEM FOR ALL VEHICLES APPLICATIONS Thank you and congratulations on the purchase of a Pacbrake onboard air system. Please read the manual prior to starting to ensure you can complete the installation
More informationFUEL PUMP SYSTEM CIRCUIT
EG1182 22RE ENGINE FUEL PUMP SYSTEM CIRCUIT ONVEHICLE INSPECTION 1. CHECK FUEL PUMP OPERATION (a) Turn the ignition switch ON. HINT: Do not start the engine. (b) Using SST, connect terminals Fp and +B
More informationPARTS MANUAL JCPT 3.0 (III) ELECTRIC SCISSOR LIFTS
R PARTS MANUAL JCPT 3.0 (III) ELECTRIC SCISSOR LIFTS Decals JCPT3.0(III) Green - used to indicate operation or maintenance information. 9423011 9423023 9413019 9413011 9413013 9413015 9413017 9213011 9213031
More informationINSTALLATION, OPERATION, & MAINTENANCE MANUAL Models # MM-30, MM-30HT, MM-50, MM-50HT, & MM-50 EXL with Special HP Tool and Special HP EXL Tool
INSTALLATION, OPERATION, & MAINTENANCE MANUAL Models # MM-30, MM-30HT, MM-50, MM-50HT, & MM-50 EXL with Special HP Tool and Special HP EXL Tool INSTALLATION INSTRUCTIONS FOR THE MODEL MM-30 & MODEL MM-50
More informationCourtesy of Crane.Market
CM19 TELESCOPIC CRANE PRELIMINARY CONTENTS / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / Crane Features...4 Boom Diagram...5 Load
More informationFPU SYSTEMS OPERATION MANUAL (INCLUDING REPAIR PARTS & SPECIAL TOOL LIST) BOH Modular Workshop Container (MWC) BOH FPU Field Pack-up Units CHAPTER 5
FPU SYSTEMS OPERATION MANUAL (INCLUDING REPAIR PARTS & SPECIAL TOOL LIST) BOH Modular Workshop Container (MWC) BOH FPU Field Pack-up Units CHAPTER 5 UNIT MAINTENANCE INSTRUCTIONS 06 BOH Environmental LLC
More informationESCONDIDO FIRE DEPT TRAINING MANUAL Section DRIVER OPERATOR Page 1 of Sutphen Aerial Operations Revised
DRIVER OPERATOR Page 1 of 12 2014 Sutphen Aerial Operations Revised 12-11-17 PROCEDURES FOR ELEVATING THE PLATFORM Placing the aerial platform into service requires qualified personnel trained in the proper
More informationPRELIMINARY CONTENTS CM190 TELESCOPIC CRANE
CM190 TELESCOPIC CRANE PRELIMINARY CONTENTS /////////////////////////////////////////////////////////// Crane Features...4 Boom Diagram...5 Load Chart: Main Boom & Jib...6 LMI Codes...7 Reeving Diagram...7
More informationRADIATOR CLEANING OF RADIATOR
CO20 COOLING SYSTEM RADIATOR CLEANING OF RADIATOR Using water or a steam cleaner, remove any mud and dirt from the radiator core. CAUTION: If using a high pressure type cleaner, be careful not to deform
More informationClick Here for Printable PDF File
HWH Online Technical School Lesson 13: Hydraulic Leveling System Identification and Operation PART 2 Computer-Control (Automatic) Leveling Systems The 400 Series 610 Central Ground Series (400 / 500 /
More informationESCONDIDO FIRE DEPT TRAINING MANUAL Section DRIVER OPERATOR Page 1 of Sutphen Aerial Operations Revised
DRIVER OPERATOR Page 1 of 10 1997 Sutphen Aerial Operations Revised 12-11-17 PROCEDURES FOR ELEVATING THE PLATFORM Placing the aerial platform into service requires qualified personnel trained in the proper
More informationProperty of American Airlines
Section 4. Specifications 1. GENERAL This vehicle specification outlines the product definition of the B350 offered by JBT, Ground Support Equipment. Tractors in this line are equipped with diesel powered
More informationOPERATION/SAFETY MANUAL
OPERATION/SAFETY MANUAL By BARLAN ENTERPRISES INSTALLER/CONSUMER OPERATION AND SAFETY MANUAL PLEASE READ THIS MANUAL BEFORE ASSEMBLING AND OPERATING THIS TOOL WARNING IF THE INFORMATION IN THIS MANUAL
More informationJohn Deere. MODEL: 450-C Crawler JD-O-OMT71338
John Deere MODEL: 450-C Crawler THIS IS A MANUAL PRODUCED BY JENSALES INC. WITHOUT THE AUTHORIZATION OF JOHN DEERE OR IT'S SUCCESSORS. JOHN DEERE AND IT'S SUCCESSORS ARE NOT RESPONSIBLE FOR THE QUALITY
More informationCHAPTER 29 HYDRAULICS Description Hydraulic Pump Hydraulic Reservoir Hydraulic Servos
Section Title CHAPTER 29 HYDRAULICS 29-00 Description............................................... 29.1 29-10 Hydraulic Pump............................................ 29.1 29-20 Hydraulic Reservoir.........................................
More informationYOUR TALL ACCESS PASS
SCISSOR LIFT 19, 20, 26, & 32 FT. PLATFORM HEIGHTS YOUR TALL ACCESS PASS 500 1000 lb. Capacity 24V AC Drive Motors Zero Degree Inside Turn Radius SV1930E SV2032E SV2632E SV2646E SV3246E AICHI SCISSOR LIFT
More informationHELPING HAND EXPERT 2000
HELPING HAND Release date: January 2005 Part #47916 rev. 0 2-2 2-3 HELPING HAND AUTOMATED ARM Table of contents 2.0 HELPING HAND MAINTENANCE... 2-5 2.1 HYDRAULIC SYSTEM MAINTENANCE... 2-5 2.1.1 HYDRAULIC
More informationLow usage. Mild climate
III. R PSL-0 STEP-LIFT MAINTENANCE egular maintenance of the Ricon PSL-0 Wheelchair and Standee Step-lift is essential for optimum performance and will reduce the need for repairs. This chapter contains
More informationTailgates By THIEMAN M16, 20, 25, 30 MLB16, 20, 25, 30 INSTALLATION INSTRUCTIONS
STOWAWAY Tailgates By THIEMAN M16, 20, 25, 30 MLB16, 20, 25, 30 INSTALLATION INSTRUCTIONS M-25 shown! IMPORTANT! KEEP IN VEHICLE! PLEASE READ AND UNDERSTAND THE CONTENTS OF THIS MANUAL BEFORE OPERATING
More informationPyrolance, LLC SPECIFICATIONS FOR DIESEL ENGINE DRIVEN ULTRA HIGH PRESSURE FIRE FIGHTING SYSTEM B2000 M-D
SPECIFICATIONS FOR DIESEL ENGINE DRIVEN ULTRA HIGH PRESSURE FIRE FIGHTING SYSTEM B2000 M-D 1 HIGH PRESSURE FIRE FIGHTING SPECIFICATIONS Scope and General Design Requirements A fire fighting system shall
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS FOR WHEELCHAIR LIFT MODEL NO. WL7-vers. B DOT-Public Use Lift PATENTS PENDING MAXON Lift Corp. 2006 MP-06-01 REV. B AUGUST 2006 PATENTS PENDING TABLE OF CONTENTS INTRODUCTION...4
More informationSERVICE BULLETIN SB1212
SERVICE BULLETIN SB1212 ADDRESSEES COACH/BUS MODEL BULLETIN TYPE SECTION/CHAPTER : ABC Customer Care and Parts Source : C2045, T2100 Series : Service Information : Section 9 Electrical system Chapter 14.2
More informationENGINE REMOVAL & INSTALLATION
TORQUE VALUES ENGINE MOUNTING = Apply Victory All Purpose Grease 2872187 1. Install all bolts in order A-H Do not tighten. E 41 Nm (30 lb-ft) M8 x 25mm D 111 Nm (82 lb-ft) 12 x 100mm ENGINE INSTALLATION
More informationINSTALLATION INSTRUCTIONS FOR WHEELCHAIR LIFT MODEL NO. WL7-vers. C WL7-vers. C-1K
INSTALLATION INSTRUCTIONS FOR WHEELCHAIR LIFT MODEL NO. WL7-vers. C WL7-vers. C-1K DOT-Public Use Lift PATENTS PENDING FOR INSIDE VEHICLE INSTALLATION ONLY MAXON Lift Corp. 2011 MP-11-01 JULY 2011 PATENTS
More informationA B C D E F. Tools Required (supplied by others)
Page 1 of 17 Parts List Below Deck Automatic Retractable Security Cover Kit (1) Tube End Bearing Plate (A) (1) Rope Reel and Cover Drum Motor Assembly (B) (1) Cover Drum (1) Pulley Support Channel (2)
More informationservice bulletin MCM 4.3L, 4.3LX Alpha GM Generation II Engine Specifications No
service bulletin TO: SERVICE MANAGER MECHANICS PARTS MANAGER No. 91-17 MCM 4.3L, 4.3LX Alpha GM Generation II Engine Specifications NOTE: These engines have an electric fuel pump because there is no pad
More informationLGT-306L / LB Club Car Precedent LED Light Bar Bumper Kit Installation Instructions
LGT-306L / LB Club Car Precedent LED Light Bar Bumper Kit Installation Instructions Caution: Please read through the instructions carefully. Before starting this project, remove the system s positive and
More informationBA440 PISTON. Hydraulic Air Compressor
P M BA440 PISTON Hydraulic Air Compressor This manual must be read carefully before using your Boss Industries, LLC BA440 PISTON. Store in a safe and convenient location for future reference. http://www.bossair.com
More informationHy-Brid Lifts HB-P827 HB-P1027 SERIES 1 MAINTENANCE & TROUBLESHOOTING PUSH-AROUND AERIAL WORK PLATFORM. Part NO. SUPO-670 May 2014
MAINTENANCE & TROUBLESHOOTING PUSH-AROUND AERIAL WORK PLATFORM Part NO. SUPO-670 May 2014 HB-P827 HB-P1027 SERIES 1 NOTES If there is a question about application and/or operation, contact: CUSTOM EQUIPMENT,
More informationP O W E R P U M P S SECTION INDEX. Proper Size & Selection G1 Series Electric...
SECTION INDEX Proper Size & Selection... 44-45 G1 Series Electric... 46-47 2 Series Electric... 48-49 G3 Series Electric... 5-51 G4 Series Electric... 52-53 P O W E R P U M P S G5 Series Electric... 54-55
More informationCONTENTS TC500 SERIES TELESCOPIC CRANE
TC500 SERIES TELESCOPIC CRANE CONTENTS /////////////////////////////////////////////////////////////////////////////////////////////////////////////// Crane Features...4 5096S Chassis Data - S Models...
More information2007 Pontiac G BRAKES Disc Brakes - G6
REAR DISC BRAKE PADS REPLACEMENT Removal Procedure CAUTION: Refer to Brake Dust Caution. 1. Inspect the fluid level in the brake master cylinder reservoir. 2. If the brake fluid level is midway between
More informationK-SERIES PUBLIC USE LIFT OPERATING INSTRUCTIONS
-PRINT- II. T K-SERIES PUBLIC USE LIFT OPERATING INSTRUCTIONS -TABLE OF CONTENTS- his chapter contains safety precautions, daily safety check instructions, control and indicator descriptions, and operating
More informationA B C D E F. b.tools Required (supplied by others) 3/16" Drill Bit 3/8" Wrench Phillips Head Screwdriver
Page 1 of 13 5E.1 Parts List a. Below Deck Automatic Retractable Security Cover Kit (1) Tube End Bearing Plate (A) (1) Rope Reel with Motor Attached (B) (1) Rope Reel Cover (C) (1) Cover Drum (1) Cover
More information650 Series Cargo Van Lift Mounting Instructions Fullsize Ford 1992-Present
TOMMY GATE OWNER'S / OPERATOR'S MANUAL 650 Series 650 LB Capacity 650 Series Cargo Van Lift Mounting Instructions Fullsize Ford 1992-Present Installing the Base Plate 1. Examine the interior and exterior
More informationPOWERSHIFT TRANSMISSION
1. Specifications... 5-3 2. Structure... 5-4 2.1 Torque converter... 5-4 2.2 Transmission... 5-5 2.3 Power Train Line... 5-6 2.4 Control Valve... 5-7 2.5 Main Regulator Valve... 5-7 2.6 Torque Converter
More informationCrane Installed on Cab & Chassis
Price quote for: Crane Installed on Cab & Chassis Vendor Name: Contact Person: Street Address: P.O. Box: City, State, Zip Phone #: Toll Free #: Fax #: Email Address: Aspen Equipment Company Mark Lundeen
More informationCantilever Series Mounting Instructions Fullsize Sprinter Van (US) All except WB (AA) present
Fullsize Sprinter Van (US) All except 3500 144 WB (AA)- 2007-present Preparing the Gate 1. Remove the platform, mounting kit, license plate assembly, and bridge assemblies, which are banded to the main
More informationHYDRAULICS. Control valves 10 spool Pilot control for left/right track travel, boom, arm, bucket & swing Manual control for auxiliary & backfill blade
CX25 Compact Excavator ENGINE Model... Yanmar 3TNE74-NYBB Cylinders... 3 Bore/Stroke... 2.91 x 3.07 (74 x 78 mm) Displacement... 61.6 in 3 (1010 cc) Fuel injection... Direct Fuel injection pump...mechanical
More informationDIY Bi-Metallic Strip
DIY Bi-Metallic Strip An introduction to the applications of thermal expansion and two-way switching. Written By: Mahaaveer BN 2018 Page 1 of 14 INTRODUCTION A bi-metallic strip is used to convert a temperature
More informationTroubleshooting Guide
Troubleshooting Guide P/N 0153180 July 1999 P.O. Box 1160 St. Joseph, MO 64502-1160 1-800-255-0317 Fax: 816-360-9379 www.snorkelusa.com GENERAL INFORMATION This manual contains procedures for locating
More informationINSTALLATION INSTRUCTIONS
TM WEIGHTLIFTER Tailgates By THIEMAN TWL 125, 16, 20 INSTALLATION INSTRUCTIONS! IMPORTANT! KEEP IN VEHICLE! PLEASE READ AND UNDERSTAND THE CONTENTS OF THIS MANUAL BEFORE OPERATING THE EQUIPMENT. NTEA T
More informationLIFT TRUCK SPECIFICATIONS
LIFT TRUCK SPECIFICATIONS RT50 2-Wheel Drive 4-Wheel Drive RT60 2-Wheel Drive 4-Wheel Drive RT80 2-Wheel Drive 4-Wheel Drive TABLE OF CONTENTS RT50 / RT60 / RT80 2-WD / 4WD Specifications / Dimensions.
More informationE E VDC COOLEDGE TILE INTERIOR INSTALLATION INSTRUCTIONS. Caution: Observe precautions for handling electrostatic sensitive devices.
5 YEAR WARRANTY 5 YEAR WARRANTY COOLEDGE TILE INTERIOR INSTALLATION INSTRUCTIONS E354088 LISTED AC E354088 58VDC E354088 E354088 5 5 YEAR WARRANTY 5 YEAR WARRANTY E354088 Caution: Observe precautions for
More information