Viking Installation Guide

Transcription

1 Viking Installation Guide Viking Range Corporation Front Street Greenwood, Mississippi 890 US (66) For product information, call -888-VIKING ( ) or visit the Viking Web site at vikingrange.com U L C U L Designer Hoods F047C EN (08908J)

2 Table of Contents Warnings & Important Information -4 DCH H. Classic Chimney Wall Hoods w/standard Ventilar Dimensions & Specifications 5 Clearance Dimensions 6 Interior Ventilar Dimensions 7 DPPV Cusm Power Packs w/standard Ventilar Dimensions & Specifications 8 Installing Hood Canopy 9 Clearance Dimensions 0 Interior Ventilar Dimensions DCWH/DCWN/DCWL Classic Chimney Wall Hoods Ledgeless & Ledge 0,, 6, 9, 4, 45, 48, & 5 Dimensions & Specifications Clearance Dimensions Interior Ventilar Dimensions 4 Exterior Ventilar Dimensions 5 DCIH Classic Chimney Island Hoods 6, 4, & 54 Dimensions & Specifications 6 Clearance Dimensions 7 Interior Ventilar Dimensions 8 Exterior Ventilar Dimensions 9 DTWS Slim Traditional Wall Hoods 0, 6, 4, & 48 Dimensions & Specifications 0 Clearance Dimensions Interior Ventilar Dimensions Exterior Ventilar Dimensions DTWN Tall Traditional Wall Hoods Ledgeless 0, 6, 4, & 48 Dimensions & Specifications 4 Clearance Dimensions 5 Interior Ventilar Dimensions 6 Exterior Ventilar Dimensions 7 DCV Wall Cusm Ventilar System Dimensions & Specifications 8 Installing Hood Canopy 9 Clearance Dimensions 0 DCV Ventilar Dimensions DICV Island Cusm Ventilar System Dimensions & Specifications Installing Hood Canopy 4 Clearance Dimensions 5 DICV Ventilar Dimensions 6 Planning Information 8 Installation Procedure Installation (DCH H. Classic Chimney Wall Hoods w/standard Ventilar) 9 Duct Cover Option (DCH H. Classic Chimney Wall Hoods w/standard Ventilar) 4 Installation (DCH H. Classic Chimney Wall Hoods w/recirculating Kit) 4 Installation (DCWH/DCWN/DCWL Classic Chimney & DTWN Tall Traditional Wall Hoods) 44 Duct Cover Option (DCWH/DCWN/DCWL Classic Chimney Wall Hoods) 45 Duct Cover Option (DTWN Tall Traditional Wall Hoods) 46 Installation (DTWS Slim Traditional) 46 Duct Cover Option (DTWS Slim Traditional Wall Hoods) 48 Installation (DCIH Classic Chimney Island Hoods) 50 Service & Registration 5 IMPORTNT Please Read and Follow! NOTE: If installing hood with warming shelf panel, install warming shelf panel first. IMPORTNT PLESE RED ND FOLLOW efore beginning, please read these instructions completely and carefully. Do not remove permanently affixed labels, warnings, or plates from the product. This may void the warranty. Please observe all local and national codes and ordinances. If no local codes are applicable, wire in accordance with the National Electrical Code, NSI/NFP 70-latest edition. Outdoor approved models should be installed in a covered non-enclosed area and should be protected from the elements as much as possible. The installer should leave these instructions with the consumer who should retain for local inspecr s use and for future reference. Check with a qualified and trained installer or local codes for makeup air requirement, if any. This hood is for residential installation only and is not designed for installation over a commercial product. Make sure power is off at the main circuit breaker or fuse box before making connections. To avoid risk of fire, electric shock, or injury persons, turn off the electricity the hood from the power supply before servicing or cleaning. Viking hoods are equipped with the variable speed controls for blowers. These units will not function with a single speed ventilar. ll Viking ventilar kits are designed specifically for use with Viking hoods. Use of any non-viking ventilar kit will void the hood warranty. RED ND SVE THESE INSTRUCTIONS W R N I N G TO REDUCE THE RISK OF RNGETOP GRESE FIRE. Never leave surface units unattended at high setting. oilovers cause smoking and greasy spillovers that may ignite. Heat oils slowly on low or medium settings.. lways turn hood ON when cooking at high heat or when cooking flaming foods. (i.e. crepes suzette, cherries jubilee, peppercorn beef flambé).. Clean ventilating fans frequently. Grease should not be allowed accumulate on fan or filter. 4. Use proper pan size. lways use cookware appropriate for the size of the surface element. W R N I N G TO REDUCE THE RISK OF FIRE, ELECTRICL SHOCK, OR INJURY TO PERSONS, OSERVE THE FOLLOWING. Installation work and electrical wiring must be done by qualified person(s) in accordance with all applicable codes and standards, including fire-rated construction.. Sufficient air is needed for proper combustion and exhausting of gases through the flute (chimney) of fuel burning equipment prevent back drafting. Follow the heating equipment manufacturer s guideline and safety standards such as those published by the National Fire Protection ssociation (NFP), and the merican Society for Heating, Refrigeration and ir Conditioning Engineers (SHRE), and the local code authorities.. When cutting or drilling in wall or ceiling, do not damage electrical wiring or other hidden utilities. 4. Ducted fans must always be vented the outdoors. 5. WRNING!: To reduce risk of fire, use only metal ductwork. 6. CUTION!: To reduce risk of fire and properly exhaust air, be sure duct air outside. Do not vent exhaust air in spaces within walls or ceilings, or in attics, crawl spaces, or garages. 7. CUTION!: To Reduce the Risk of Fire and Electric Shock, Install this rangehood only with remote blower models manufactured by Viking, model numbers DEV900/DEV00, VEV900/VEV00, OR DEV500, VEV500 or integral blowers manufactured by Viking, model numbers DIV00, DIV440, DIV600, DIV800, DIV00, VIV00, VIV600, or VIV00. NOTE Please refer inside for specific canopy/blower combinations. W R N I N G TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, OR INJURY TO PERSONS, OSERVE THE FOLLOWING Use this unit only in the manner intended by the manufacturer. If you have any questions, contact the manufacturer. efore servicing or cleaning unit, switch power off at service panel and lock service panel prevent power from being switched on accidentally. When the service disconnecting means cannot be locked, securely fasten a prominent warning device, such as a tag, the service panel.

3 IMPORTNT Please Read and Follow! W R N I N G TO REDUCE THE RISK OF INJURY TO PERSONS IN THE EVENT OF RNGETOP GRESE FIRE, OSERVE THE FOLLOWING. (ased on Kitchen Firesafety Tips, published by NFP.). SMOTHER FLMES with a close fitted lid, cookie sheet, or metal tray, then turn off the burner. E CREFUL TO PREVENT URNS. If the flames do not go out immediately, EVCUTE ND CLL THE FIRE DEPRTMENT.. NEVER PICK UP FLMING PN. You may be burned.. DO NOT USE WTER, including wet dishcloths or wels a violent steam explosion will result. 4. Use an extinguisher ONLY if You know it is a Class C extinguisher, and you already know how operate it. The fire is small and contained in the area where it started. The fire department is being called. You can fight the fire with your back an exit. C U T I O N For general ventilating use only. Do not use exhaust hazardous or explosive materials and vapors. W R N I N G TO REDUCE THE RISK OF FIRE, ELECTRICL SHOCK, OR INJURY TO PERSONS Rangehoods must be installed with the ventilars that are specified on their carn indicating suitability with this model. Other ventilars cannot be substituted. 0 W. 6 W. Dimensions & Specifications (DCH H. Classic Chimney Wall Hoods w/standard Ventilar) (5. cm) (Hood width) 9-7/8 (75.9 cm) 5-7/8 (9. cm) NOTE: Optional duct cover sold separately. (0.5 cm) DCH H. Classic Chimney Wall Hoods w/standard Ventilar 4 (6.0 cm) Description 0 6 Duct cover width 6 (40.6 cm) Duct cover depth (0.5 cm) Duct cover height 8 (45.7 cm) 0 (76. cm) Number of lights Number of filters Interior ventilar kit 460 CFM Interior duct size* 7 (7.8 cm) Interior Maximum amps (40.6 cm) 8 (0.5 cm) 0 (76. cm) (0.5 cm) * Disregard when using recirculating kits. 460 CFM blower is shipped with hood. NOTE: ll products must be hard wired with -wire with ground. 4 5

4 Clearance Dimensions (DCH H. Classic Chimney Wall Hoods w/standard Ventilar) Interior Ventilar Dimensions (DCH H. Classic Chimney Wall Hoods w/standard Ventilar) 6 (40.6 cm) 66 min. (67.6 cm) 69 max. (75. cm) 0 min. (76. cm) max. (8.8 cm) 0 W. 6 W. 4-5/6 (7.9 cm) 7-5/6 (45.6 cm) 4 (0. cm) 9-/4 (4.8 cm) 6 (9.4 cm) 0 V 7 (7.8 cm) dia. duct location 460 CFM Interior Ventilar Installation 6 7

5 Dimensions & Specifications (DPPV Cusm Power Packs w/standard Ventilar System) Installing Hood Canopy (Cusm Hood Canopy Cuuts) *For best results, center the unit over the burners of the cooking product (front back; right left). * * Make sure the back wall of the cusm hood canopy is flush with the cuut so the ventilar system may be mounted as shown on page 9. Cusm Hood Canopy otm Cuut Dimensions Power Packs Description (Hood Width) (Hood Depth) 0 W. 8-/6 (7.9 cm) 6-/ (4.9 cm) 6 W. 4-/6 (88. cm) 6-/ (4.9 cm) DPPV Cusm Power Packs w/standard Ventilar System Description 0 6 Number of lights Number of filters Interior ventilar kit 460 CFM Interior duct size 7 (7.8 cm) Interior Maximum amps CFM blower is shipped with hood. NOTE: ll products must be hard wired with -wire with ground. ) Position ventilar system inside of the cusm hood canopy and center it front back and left right. ) otm mounting holes fasten ventilar system botm of cusm hood canopy with the screws provided. uilt-in Ventilar System ) OPTIONL Rear mounting holes fasten ventilar system rear of cusm hood canopy. 8 9

6 Clearance Dimensions (DPPV Cusm Power Packs w/standard Ventilar System) Interior Ventilar Dimensions (DPPV Cusm Power Packs w/standard Ventilar System) (Cusm Hood) 6 (40.6 cm) 66 min. (67.6 cm) 69 max. (75. cm) 0 min. (76. cm) max. (8.8 cm) 0 W. 6 W. 4-5/6 (7.9 cm) 7-5/6 (45.6 cm) 4 (0. cm) 9-/4 (4.8 cm) 6 (9.4 cm) 0 V 7 (7.8 cm) dia. duct location 460 CFM Interior Ventilar Installation 0

7 Dimensions & Specifications (DCWH Classic Chimney Wall Hoods 0, 6, 4, & 48 ) (DCWN Ledgeless models 0, 6, 4, & 48 ) (DCWL Ledge models, 9, 45, & 5 ) Clearance Dimensions (DCWH/DCWN/DCWL Classic Chimney Wall Hoods) (Duct cover width) 0 W. 0 (5.4 cm) W. 0 (5.4 cm) 6 W. (0.5 cm) 9 W. (0.5 cm) 4 W. (0.5 cm) 45 W. (0.5 cm) 48 W. 8 (45.7 cm) 5 W. 8 (45.7 cm) 0 W. 6 W. 4 W. 48 W. (Hood width) 9-7/8 (75.9 cm) 5-7/8 (9. cm) 4-7/8 (06.4 cm) 47-7/8 (.6 cm) C (Hood width Ledge models) W. -7/8 (8.5 cm) 9 W. 8-7/8 (98.4 cm) 45 W. 44-7/8 (4.0 cm) 5 W. 50-7/8 (9. cm) (5. cm) C (0.5 cm) 4 (6.0 cm) 5-/ (64.8 cm) Ledge models only *,00 CFM interior- or exterior-power ventilar should be used when installed over range/rangep with gas char-grill. Max duct run is 50 ft. ** It is recommended that the,500 CFM ventilar be used with longer duct runs. Max duct run is 75 ft. NOTE: Maximum amp rating for hoods includes recommended ventilar kit rating; ll products must be hard wired with -wire with ground. n interior- or exterior-power ventilar kit must be purchased for installation with all Designer hoods. D E 0 / W. 6 /9 W. 4 /45 W. 48 /5 W. D (Duct height) 8 (45.7 cm) 0 (76. cm) 6 (40.6 cm) 8 (7. cm) E (Hood height) 0 W. (0.5 cm) W. (0.5 cm) 6 W. 4 (5.6 cm) 9 W. 4 (5.6 cm) 4 W. 4 (5.6 cm) 45 W. 4 (5.6 cm) 48 W. 4 (5.6 cm) 5 W. 4 (5.6 cm) DCWH/DCWN/DCWL Classic Chimney Wall Hoods Ledgeless & Ledge Description 0 / 6 /9 4 /45 48 /5 Duct cover width 0 (5.4 cm) (0.5 cm) (0.5 cm) 8 (45.7 cm) Duct cover depth (0.5 cm) Duct cover height 8 (45.7 cm) 6 (40.6 cm) 6 (40.6 cm) 6 (40.6 cm) 0 (76. cm) 8 (7. cm) 8 (7. cm) 8 (7. cm) Number of lights Number of filters Interior ventilar kits DIV00/ DIV00/ DIV600 DIV00* DIV440 DIV600 Exterior ventilar kits DEV900/ DEV900/ DEV900/ DEV00*/ DEV00* DEV00* DEV00* DEV500** Interior duct size 7 (7.8 cm) 7 (7.8 cm) 7 (7.8 cm) 0 (5.4 cm) Exterior duct size 0 (5.4 cm) Interior Maximum amps.7/..7/ Exterior Maximum amps 6.6./ /.9 6.6/.9 4./5. 6 (9.4 cm) 66 min. (67.6 cm) 7 max. (8.9 cm) NOTE: For best performance, it is recommended that the botm of the hood be 0 (76. cm) 6 (9.4 cm) above the counterp. These dimensions provide for safe and efficient operation of the hood. 0 min. (76. cm) 6 max. (9.4 cm)

8 Interior Ventilar Dimensions (DCWH/DCWN/DCWL Classic Chimney Wall Hoods) Exterior Ventilar Dimensions (DCWH/DCWN/DCWL Classic Chimney Wall Hoods) 0 W. W. 6 W. 9 W. 4 W. 45 W. 0 W. W. 6 W. 9 W. 4 W. 45 W. 0 (5.4 cm) 0 (5.4 cm) (0.5 cm) (0.5 cm) (0.5 cm) (0.5 cm) 4-5/6 (7.9 cm) 4-5/6 (7.9 cm) 7-5/6 (45.6 cm) 7-5/6 (45.6 cm) 0-5/6 (5. cm) 0-5/6 (5. cm) -/ -/ (.8 cm) (.8 cm) 0V power supply 6 (5. cm) 7 (7.8 cm) dia. duct location -/ (.8 cm) Classic Chimney Classic Chimney w/ledge 0 W. W. 6 W. 9 W. 4 W. 45 W. 0 W. W. 6 W. 9 W. 4 W. 45 W. 0 (5.4 cm) 0 (5.4 cm) (0.5 cm) (0.5 cm) (0.5 cm) (0.5 cm) 4-5/6 (7.9 cm) 4-5/6 (7.9 cm) 7-5/6 (45.6 cm) 7-5/6 (45.6 cm) 0-5/6 (5. cm) 0-5/6 (5. cm) -/ -/ (.8 cm) (.8 cm) 0V power supply 6 (5. cm) C -/ (.8 cm) C (Duct diameter) 0 W. 8 (0. cm)* W. 8 (0. cm)* 6 W. 0 (5.4 cm) 9 W. 0 (5.4 cm) 4 W. 0 (5.4 cm) 45 W. 0 (5.4 cm) * 8 0 transition be acquired locally. Classic Chimney Classic Chimney w/ledge 00, 440 or 600 CFM Interior Ventilar Installation for 0,, 6, 9, 4, & 45 models 900 or 00 CFM Exterior Ventilar Installation for 0,, 6, 9, 4, & 45 models 8 (45.8 cm) -/ -/ (.8 cm) (.8 cm) -5/6 0 V (60.8 cm) power supply 6 (5. cm) -/ (.8 cm) Classic Chimney -/ (.8 cm) -5/6 (60.8 cm) 6 (5. cm) 8 (45.8 cm) -/ (.8 cm) -/ (.8 cm) 0 V power supply Classic Chimney 0 (5.4 cm) dia. duct location Classic Chimney w/ledge 0 (5.4 cm) dia. duct location Classic Chimney w/ledge 00 CFM Interior Ventilar Installation for 48 & 5 models 00 or 500 CFM Exterior Ventilar Installation for 48 & 5 models 4 5

9 Dimensions & Specifications (DCIH Classic Chimney Island Hoods 6, 4, & 54 ) Clearance Dimensions (DCIH Classic Chimney Island Hoods) (Duct cover width) 6 W. (0.5 cm) 4 W. (0.5 cm) 54 W. 8 (45.7 cm) (0.5 cm) C (Duct height) 6 W. 6 (40.6 cm) or 4 W. 8 (7. cm) or 54 W. 40 (0.6 cm) (5. cm) C 4 (5.6 cm) (Hood width) 6 W. 5-7/8 (9. cm) 4 W. 4-7/8 (06.4 cm) 54 W. 5-7/8 (6.8 cm) 0 (76. cm) 66 min. (67.6 cm) 7 max. (8.9 cm) 0 min. (76. cm) 6 max. (9.4 cm) NOTE: Optional duct cover sold separately. DCIH Classic Chimney Island Hoods Description Duct cover width (0.5 cm) (0.5 cm) 8 (45.7 cm) Duct cover depth (0.5 cm) Duct cover height 6 (40.6 cm) or 8 (7. cm) or 40 (0.6 cm) Number of lights Number of filters Interior ventilar kits DIV600 DIV600 DIV00* Exterior ventilar kits DEV900/ DEV900/ DEV00*/ DEV00* DEV00*/DEV500** DEV00*/DEV500** Interior duct size 7 (7.8 cm) 7 (7.8 cm) 0 (5.4 cm) Exterior duct size 0 (5.4 cm) Interior Maximum amps Exterior Maximum amps 6.6./.9 7.4/4.7/ /6.4 *,00 CFM interior- or exterior-power ventilar should be used when installed over range/rangep with gas char-grill. Max duct run is 50 ft. ** It is recommended that the,500 CFM ventilar be used with longer duct runs. Max duct run is 75 ft. NOTE: Maximum amp rating for hoods includes recommended ventilar kit rating; ll products must be hard wired with -wire with ground. n interior- or exterior-power ventilar kit must be purchased for installation with all Designer hoods. 6 (9.4 cm) NOTE: For best performance, it is recommended that the botm of the hood be 0 (76. cm) 6 (9.4 cm) above the counterp. These dimensions provide for safe and efficient operation of the hood. 6 7

10 Interior Ventilar Dimensions (DCIH Classic Chimney Island Hoods) Exterior Ventilar Dimensions (DCIH Classic Chimney Island Hoods) 6 W. 4 W. 7-5/6 (45.6 cm) 0-5/6 (5. cm) (0.5 cm) (0.5 cm) 4-/4 (. cm) 4-/4 (. cm) 6 W. 4 W. 7-5/6 (45.6 cm) 0-5/6 (5. cm) (0.5 cm) (0.5 cm) 4-/4 (. cm) 4-/4 (. cm) 5 (8. cm) 7 (7.8 cm) dia. duct location 0 V power supply 5 (8. cm) 0 (5.4 cm) dia. duct location 0 V power supply 600 CFM Interior Ventilar Installation for 6 & 4 models 900 or 00 CFM Exterior Ventilar Installation for 6 & 4 models 6-5/6 (68.4 cm) 8 (45.7 cm) 6-5/6 (68.4 cm) 8 (45.7 cm) 5 (8. cm) 7 (7.8 cm) 0 V power supply 5 (8. cm) 7 (7.8 cm) 0 V power supply 6 (5. cm) (0.5 cm) 6 (5. cm) (0.5 cm) 0 (5.4 cm) dia. duct location 0 (5.4 cm) dia. duct location 00 CFM Interior Ventilar Installation for 54 models 00 or 500 CFM Exterior Ventilar Installation for 54 models 8 9

11 Dimensions & Specifications (DTWS Slim Traditional Wall Hoods 0, 6, 4, & 48 ) Clearance Dimensions (DTWS Slim Traditional Wall Hoods) (Duct cover width) 0 W. (0.5 cm) 6 W. (0.5 cm) 4 W. (0.5 cm) 48 W. 0 (50.8 cm) (.0 cm) (0.5 cm) (5. cm) (5. cm) (8.8 cm) 0 W. 6 W. 4 W. 48 W. (Hood width) 9-7/8 (75.9 cm) 5-7/8 (9. cm) 4-7/8 (06.4 cm) 47-7/8 (.6 cm) 4 (6.0 cm) 9 (.9 cm) 66 min. (67.6 cm) 7 max. (8.9 cm) 0 min. (76. cm) 6 max. (9.4 cm) DTWS Slim Traditional Wall Hoods Description Duct cover width (0.5 cm) (0.5 cm) (0.5 cm) 0 (50.8 cm) Duct cover depth (0.5 cm) Duct cover height (5. cm) (8.8 cm) Number of lights Number of filters Interior ventilar kits DIV00/ DIV00/ DIV440 DIV880 DIV440 DIV440 Exterior ventilar kits DEV900 DEV900 DEV900 DEV00*/ DEV500** Interior duct size (7.8 cm) (7.8 cm) (7.8 cm) (5.4 cm) Exterior duct size 0 (5.4 cm) Interior Maximum amps.7/..7/ Exterior Maximum amps /5. *,00 CFM interior- or exterior-power ventilar should be used when installed over range/rangep with gas char-grill. Max duct run is 50 ft. ** It is recommended that the,500 CFM ventilar be used with longer duct runs. Max duct run is 75 ft. NOTE: Maximum amp rating for hoods includes recommended ventilar kit rating; ll products must be hard wired with -wire with ground. n interior- or exterior-power ventilar kit must be purchased for installation with all Designer hoods. 6 (9.4 cm) NOTE: For best performance, it is recommended that the botm of the hood be 0 (76. cm) 6 (9.4 cm) above the counterp. These dimensions provide for safe and efficient operation of the hood. 0

12 Interior Ventilar Dimensions (DTWS Slim Traditional Wall Hoods) Exterior Ventilar Dimensions (DTWS Slim Traditional Wall Hoods) -/8 (.9 cm) 5-9/6 (4. cm) -/8 (.9 cm) 5-9/6 (4. cm) 0 W. 5-/4 (40.0 cm) 5-/8 (.0 cm) 0 W. 5-/4 (40.0 cm) 5-/8 (.0 cm) 6 W. 4 W. 8-/4 (47.6 cm) -/4 (55. cm) 0 V power supply 6 W. 4 W. 8-/4 (47.6 cm) -/4 (55. cm) 0 V power supply (7.9 cm) 7 (7.8 cm) dia. duct location (7.9 cm) 8 (0. cm)* dia. duct location * 8 0 transition be acquired locally. 00 or 440 CFM Interior Ventilar Installation for 0, 6, & 4 models 900 or 00 CFM Exterior Ventilar Installation for 0, 6 & 4 models -5/6 (60. cm) 7-7/8 (0.0 cm) -5/6 (60. cm) 7-7/8 (0.0 cm) -/8 (.9 cm) -/8 (.9 cm) 6 (5. cm) 6 (5. cm) 0 V 0 V 9 (48. cm) 0 (5.4 cm) dia. duct location 9 (48. cm) 0 (5.4 cm) dia. duct location 880 CFM Interior Ventilar Installation for 48 models 00 or 500 CFM Exterior Ventilar Installation for 48 models

13 Dimensions & Specifications (DTWN Tall Traditional Wall Hoods Ledgeless 0, 6, 4, & 48 ) Clearance Dimensions (DTWN Tall Traditional Wall Hoods) (Duct cover width) 0 W. 9-7/8 (75.9 cm) 6 W. 5-7/8 (9. cm) 4 W. 4-7/8 (06.4 cm) 48 W. 47-7/8 (.6 cm) (0.5 cm) (5. cm) Ledge models only (0.5 cm) 8 (45.7 cm) 66 min. 0 W. 6 W. 4 W. 48 W. (Hood width) 9-7/8 (75.9 cm) 5-7/8 (9. cm) 4-7/8 (06.4 cm) 47-7/8 (.6 cm) NOTE: Optional duct cover sold separately. DTWN Tall Traditional Wall Hoods Ledgeless Description Duct cover width 9-7/8 (75.9 cm) 5-7/8 (9. cm) 4-7/8 (06.4 cm) 47-7/8 (.6 cm) Duct cover depth (0.5 cm) Duct cover height (0.5 cm) Number of lights Number of filters Interior ventilar kits VIV00/ VIV00/ VIV600/ VIV00* VIV600/VIV00* VIV600/VIV00* VIV00* Exterior ventilar kits VEV900/00* VEV900/00* VEV900/00* VEV00*/500** Interior duct size 7 (7.8 cm) 7 (7.8 cm) 7 (7.8 cm) 0 (5.4 cm) Exterior duct size 0 (5.4 cm) Interior Maximum amps.4/4.6/6.6.4/4.6/ / Exterior Maximum amps 6.6/.9 6.6/.9 6.6/.9 4./5. *,00 CFM interior- or exterior-power ventilar should be used when installed over range/rangep with gas char-grill. Max duct run is 50 ft. ** It is recommended that the,500 CFM ventilar be used with longer duct runs. Max duct run is 75 ft. NOTE: Maximum amp rating for hoods includes recommended ventilar kit rating; ll products must be hard wired with -wire with ground. n interior- or exterior-power ventilar kit must be purchased for installation with all Designer hoods. 4 (6.0 cm) 5-/ (64.8 cm) Ledge models only 6 (9.4 cm) (67.6 cm) 7 max. (8.9 cm) NOTE: For best performance, it is recommended that the botm of the hood be 0 (76. cm) 6 (9.4 cm) above the counterp. These dimensions provide for safe and efficient operation of the hood. 0 min. (76. cm) 6 max. (9.4 cm) 4 5

14 Interior Ventilar Dimensions (DTWN Tall Traditional Wall Hoods) Exterior Ventilar Dimensions (DTWN Tall Traditional Wall Hoods) 8-/4 (47.6 cm) 8-/4 (0.9 cm) (Duct diameter) VIV00 7 (7.8 cm)/0 (5.4 cm) VIV600 7 (7.8 cm)/0 (5.4 cm) VIV00 0 (5.4 cm) 4-5/8 (.7 cm) 9-/8 (. cm) 9-/8 (.8 cm) 0 V 9-5/8 (4.4 cm) (Duct diameter) 0 W. 4-5/6 (7.9 cm) 6 W. 7-5/6 (45.6 cm) 4 W. 0-5/6 (56. cm) 5-5/6 (5. cm) 0 (4.8 cm) dia. duct location 6-7/6 (6.4 cm) 0 V -/ (6.4 cm) (7.6 cm) Tall Traditional Ledgeless Tall Traditional with Ledge 00, 600, or 00 CFM Interior Ventilar Installation for 0, 6, & 4 models Tall Traditional Ledgeless Tall Traditional with Ledge 900 or 00 CFM Exterior Ventilar Installation for 0, 6, & 4 models 0 (4.8 cm) dia. duct location -5/6 (60.8 cm) 5/8 (.6 cm) 8-/6 (0.7 cm) -5/6 (60.8 cm) 5-/ (4.0 cm) 0 V 8-/8 (. cm) 5-5/6 (5. cm) 0 V 6-5/8 (6.8 cm) (7.6 cm) 9-/4 (.5 cm) 9-/ (4. cm) 8-/4 (47.6 cm) 0 (4.8 cm) dia. duct location -/ (6.5 cm) Tall Traditional Ledgeless Tall Traditional with Ledge 00 CFM Interior Ventilar Installation for 48 models Tall Traditional Ledgeless Tall Traditional with Ledge 00 or 500 CFM Exterior Ventilar Installation for 48 models 6 7

15 Dimensions & Specifications (DCV Wall Cusm Ventilar System) Installing Hood Canopy (Cusm Hood Canopy Cuuts) * *For best results, center the unit over the burners of the cooking product (front back; right left). * Make sure the back wall of the cusm hood canopy is flush with the cuut so the ventilar system may be mounted as shown on page 9. Cusm Hood Canopy otm Cuut Dimensions Wall Hoods Description (Hood Width) (Hood Depth) 0 W. 8-/6 (7.9 cm) 6-/ (4.9 cm) 6 W. 4-/6 (88. cm) 6-/ (4.9 cm) 4 W. 40-/6 (0.4 cm) 6-/ (4.9 cm) 48 W. 46-/6 (8.6 cm) 6-/ (4.9 cm) DCV Wall Cusm Ventilar System Description Number of lights Number of filters Interior ventilar kits DIV00/ DIV00/ DIV440 DIV880 DIV440 DIV440 Exterior ventilar kits DEV900/ DEV900/ DEV900/ DEV00*/ DEV00* DEV00* DEV00* DEV500** Interior duct size 7 (7.8 cm) 7 (7.8 cm) 7 (7.8 cm) 0 (5.4 cm) Exterior duct size 0 (5.4 cm) Interior Maximum amps.7/..7/ Exterior Maximum amps 6.6./ /.9 6.6/.9 4./5. *,00 CFM interior- or exterior-power ventilar should be used when installed over range/rangep with gas char-grill. Max duct run is 50 ft. ** It is recommended that the,500 CFM ventilar be used with longer duct runs. Max duct run is 75 ft. NOTE: Maximum amp rating for hoods includes recommended ventilar kit rating; ll products must be hard wired with -wire with ground. n interior- or exterior-power ventilar kit must be purchased for installation with all Designer hoods. ) Position ventilar system inside of the cusm hood canopy and center it front back and left right. ) otm mounting holes fasten ventilar system botm of cusm hood canopy with the screws provided. uilt-in Ventilar System ) OPTIONL Rear mounting holes fasten ventilar system rear of cusm hood canopy. 8 9

16 Clearance Dimensions (DCV Wall Cusm Ventilar System) uilt-in Wall Cusm Ventilar System Dimensions (0 W./6 W./4 W. DCV Models) (Cusm Hood) (7.9 cm) 8 (0. cm) (.5 cm) (7.9 cm) 7 (7.8 cm) (.5 cm) 5 (.7 cm) -/4 (9.8 cm) 5 (.7 cm) -/4 (9.8 cm) 900 or 00 CFM External Ventilar Installation 00 or 440 CFM** Internal Ventilar Installation 6 (9.4 cm) 66 min. (67.6 cm) 7 max. (8.9 cm) 0 min. (76. cm) 6 max. (9.4 cm) 6-/8 (5.6 cm) C 6 (40.6 cm) 6 (5. cm) (5. cm) /4 (.9 cm) 6-/8 (5.6 cm) C 6 (40.6 cm) 6 (5. cm) (5. cm) /4 (.9 cm) 0V 0V 7-/4 (4.8 cm) 6 (40.6 cm) 8 (0. cm) Round for External Ventilation Duct* 900 or 00 CFM External Ventilar Installation (0 diameter duct required) 7 (7.8 cm) Round for External Ventilation Duct* 00 or 440 CFM** Internal Ventilar Installation (7 diameter duct required) *Must purchase 8 diameter 0 diameter transition locally. Transition should be installed past the duct cover. NOTE: For best performance, it is recommended that the botm of the hood be 0 (76. cm) 6 (9.4 cm) above the counterp. These dimensions provide for safe and efficient operation of the hood. 0 W. 9-5/8 (75. cm) 6 W. 5-5/8 (90.5 cm) 4 W. 4-5/8 (05.7 cm) 0 W. 8-/8 (7. cm) 6 W. 4-/8 (87. cm) 4 W. 40-/8 (0.6 cm) C 0 W. 4-/6 (7.6 cm) 6 W. 7-/6 (45. cm) 4 W. 0-/6 (5.9 cm) **00 CFM ventilar kit for installation with 0 W. and 6 W. hoods only. 0

17 uilt-in Wall Cusm Ventilar System Dimensions (48 W. DCV Models) Dimensions & Specifications (DICV Island Cusm Ventilar Systems 6, 4, & 54 ) (7.9 cm) 0 (5.4 cm) * (.5 cm) 5 (.7 cm) -/4 (9.8 cm) *For best results, center the unit over the burners of the cooking product (front back; right left). * Make sure the back wall of the cusm hood canopy is flush with the cuut so the ventilar system may be mounted as shown on page CFM Internal and 00 or 500 CFM External Ventilar Installation otm Cuut Dimensions 7-/4 (4.8 cm) 6-/8 (5.6 cm) 47-5/8 (.0 cm) 46-5/8 (8.4 cm) -/6 (60.5 cm) 6 (40.6 cm) 6 (5. cm) 0 (5.4 cm) Round for External Ventilation Duct* (5. cm) 0V 880 CFM Internal and 00 or 500 CFM External Ventilar Installation (0 diameter duct required) /4 (.9 cm) Island Hoods Description (Hood Width) (Hood Depth) 6 W. 4-/6 (88. cm) -/ (54.6 cm) 4 W. 40-/6 (0.4cm) -/ (54.6 cm) 54 W. 5-/6 (.8 cm) -/ (54.6 cm) DICV Island Cusm Ventilar System Description Number of lights Number of filters Interior ventilar kits DIV440 DIV440 DIV880 Exterior ventilar kits DEV900/ DEV900/ DEV00*/ DEV00* DEV00*/DEV500** DEV00*/DEV500** Interior duct size 7 (7.8 cm) 7 (7.8 cm) 0 (5.4 cm) Exterior duct size 0 (5.4 cm) Interior Maximum amps Exterior Maximum amps 6.6./.9 7.4/4.7/ /6.4 *,00 CFM interior- or exterior-power ventilar should be used when installed over range/rangep with gas char-grill. Max duct run is 50 ft. ** It is recommended that the,500 CFM ventilar be used with longer duct runs. Max duct run is 75 ft. NOTE: Maximum amp rating for hoods includes recommended ventilar kit rating; ll products must be hard wired with -wire with ground. n interior- or exterior-power ventilar kit must be purchased for installation with all Designer hoods.

18 Installing Hood Canopy (Cusm Hood Canopy Cuuts) Clearance Dimensions (DICV Island Cusm Ventilar System) Cusm Hood Canopy (Cusm Hood) 66 min. 0 min. (67.6 cm) 7 max. (8.9 cm) (76. cm) 6 max. (9.4 cm) ) Position ventilar system inside of the cusm hood canopy and center it front back and left right. ) otm mounting holes fasten ventilar system botm of cusm hood canopy with the screws provided. uilt-in Ventilar System 6 (9.4 cm) ) OPTIONL Rear mounting holes fasten ventilar system rear of cusm hood canopy. NOTE: For best performance, it is recommended that the botm of the hood be 0 (76. cm) 6 (9.4 cm) above the counterp. These dimensions provide for safe and efficient operation of the hood. 4 5

19 uilt-in Island Cusm Ventilar System Dimensions (6 W./4 W. DICV Models) uilt-in Island Cusm Ventilar System Dimensions (54 W. DICV Models) (7.9 cm) (7.9 cm) (7.9 cm) 8 (0. cm) (.5 cm) 7 (7.8 cm) (.5 cm) 0 (5.4 cm) (.5 cm) 5 (.7cm) -/4 (9.8 cm) 5 (.7cm) -/4 (9.8 cm) 5 (.7cm) -/4 (9.8 cm) 900, 00 or 500 CFM External** Ventilar Installation 00 or 440 CFM** Internal Ventilar Installation 880 CFM Internal and 00 or 500 CFM External Ventilar Installation -/4 (56.5 cm) -/8 (8. cm) (5. cm) C /4 (.9 cm) 0V 8 (0. cm) Round for Ventilation Duct* 900, 00 or 500 CFM External** Ventilar Installation (0 diameter duct required) 6 (40.6 cm) 6 (5. cm) (5. cm) *Must purchase 8 diameter 0 diameter transition locally. Transition should be installed past the duct cover. -/4 (56.5 cm) -/8 (8. cm) (5. cm) C 6 (40.6 cm) 6 (5. cm) 7 (7.8 cm) Round for Ventilation Duct* (5. cm) /4 (.9 cm) 0V 00*** or 440 CFM** Internal Ventilar Installation (7 diameter duct required) -/4 (56.5 cm) -/8 (8. cm) (5. cm) 6-/6 (68. cm) 5-5/8 (6. cm) 5-5/8 (.7 cm) 4 (6.0 cm) 0 (5.4 cm) (5. cm) /4 (.9 cm) 0V 0 (5.4 cm) Round for Ventilation Duct 880 CFM Internal and 00 or 500 CFM External Ventilar Installation (0 diameter duct required) 6 W. 5-5/8 (90.5 cm) 4 W. 4-5/8 (05.7 cm) 6 W. 4-5/8 (87.9 cm) 4 W. 40-5/8 (0. cm) C 6 W. 7-/6 (45. cm) 4 W. 0-/6 (5.9 cm) **500 CFM external ventilar kit for installation with 4 W. island hood only. ***00 CFM ventilar kit for installation with 0 W. and 6 W. hoods only. 6 7

20 Planning Information Installation (DCH H. Classic Chimney Wall Hoods w/standard Ventilar and DPPV Cusm Power Packs w/standard Ventilar) Plan where the duct work will be located. Install proper-sized duct work, roof, or wall cap for the type of blower you are using. djust your measurements for various heights of ceilings, soffits, cabinets, or ranges/rangeps. Roof cap 7 round duct 00 or 600 CFM single blower interior-power typical ductwork Duct cover or soffit Proper installation of ducting is extremely important ensure maximum performance from any ventilation product. ll CFMs are based on tests at 0. static pressure: without applying static pressure, CFM would be greatly overstated. Straight runs and gradual turns are best; for example, each 90º elbow is equivalent 5-0 feet ( cm) of straight run. Never use flexible duct; it creates back pressure/air turbulence and greatly reduces performance. Proper performance is dependent on proper ducting; make sure that a qualified and trained installer is used. Check with a qualified and trained installer or local codes for makeup air requirement, if any. Max. amp rating for hoods includes recommended ventilar kit rating; all products must be hard wired direct with -wire with ground. Check Framing Roof cap 0 round duct Exterior blower 0 round duct Hood 00 CFM single blower interior power typical ductwork Duct cover or soffit Hood 900, 00, or 500 CFM exterior power typical ductwork Duct cover or soffit Hood Check damper for unrestricted movement, adjust if necessary. ttach transition damper. Seal with aluminum tape. W R N I N G TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, OR INJURY TO PERSONS, OSERVE THE FOLLOWING Use this unit only in the manner intended by the manufacturer. If you have any questions, contact the manufacturer. efore servicing or cleaning unit, switch power off at service panel and lock service panel prevent power from being switched on accidentally. When the service disconnecting means cannot be locked, securely fasten a prominent warning device, such as a tag, the service panel. Wall cap Wall installation exterior power typical ductwork Flip hood over and remove electrical box cover. Duct Duct cover or soffit Hood 4 5 NOTE: ecause of the weight of the hood make sure that the mounting screws are driven in the framing and not just the drywall. It may be necessary drill additional holes in the canopy for proper alignment. Some hoods require a locally supplied wood strip for mounting. Check installation procedure of your hood on page 4 determine if a wood strip is required. NOTE: Wall exhaust must be a minimum of 4 (6.0 cm) from ground. This may vary depending on local codes and geographic location. Electrical Supply Run 0 VC electrical wiring from service panel installation location. See specification pages for the maximum amp requirements. Insert 6 of electrical wiring through the p of vent hood and secure using wiring restrain. Refer local codes. Slide duct over transition and tape around joint. 8 9

21 6 5/6 nut driver 5/6 nut driver CUTION: Secure vent hood wall using screws provided. Use additional mounting screws and wall anchors, if necessary. 7 RE OR GREEN CUTION: If not using a duct cover, using screws provided make sure p mounting screws are secured in soffit or cabinet frame. Use additional mounting screws, if necessary. 8 Slide filter front over front lip. Push filter rear up, then slide back over rear lip. Duct Cover Option (DCH H. Classic Chimney Wall Hoods w/standard Ventilar) WHITE GREEN LCK WHITE LCK Connect black black, white white, and the green/bare wire under the green screw. NOTE: Housing wiring must be properly installed for wiring be correct when wiring unit. Replace electrical box cover. Make connection breaker box. Measure distance from ceiling canopy. Tape avoid scratching Slide filter front over front lip. Push filter rear up, then slide back over rear lip. Slide spacer front over front lip. Push spacer rear up, then slide back over rear lip. Place duct cover p inside duct cover base and lower until desired height is found. Mark height. Use the retaining nuts and bolts fasten in place from the inside and remove tape. Slide duct cover in place and fasten from inside canopy using the sheet metal screws provided. 40 4

22 Installation (DCH H. Classic Chimney Wall Hoods w/recirculating Kit) 6 7 5/6 nut driver Remove damper and discard with transition. Turn recirculating unit upside down. Place vent hood upside down on recirculating unit. Flip hood over. Insert 6 of electrical wiring through the p of vent hood and secure using wiring restrain. Refer local codes. CUTION: Secure vent hood. Make sure mounting screws are secured in framing using additional mounting screws and wall anchors, if necessary. 4 8 RE OR GREEN 9 WHITE GREEN LCK WHITE LCK ttach with screws and lock washers provided. 5 ttach with screws. W R N I N G TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, OR INJURY TO PERSONS, OSERVE THE FOLLOWING Use this unit only in the manner intended by the manufacturer. If you have any questions, contact the manufacturer. efore servicing or cleaning unit, switch power off at service panel and lock service panel prevent power from being switched on accidentally. When the service disconnecting means cannot be locked, securely fasten a prominent warning device, such as a tag, the service panel. Connect black black, white white, and the green/bare wire under the green screw. NOTE: Housing wiring must be properly installed for wiring be correct when wiring unit. 0 Replace electrical box cover. Make connection breaker box. Remove electrical box cover. ssemble brackets mesh filters and insert charcoal filters. Slide filter front over front lip. Push filter rear up, then slide back over rear lip. 4 4

23 4 To install ventillation kit refer ventillation kit installation instructions. Slide spacer front over front lip. Push spacer rear up, then slide back over rear lip. Slide filter front over front lip. Push filter rear up, then slide back over rear lip. Slide filter front over front lip. Push filter rear up, then slide back over rear lip. Installation (DCWH/DCWN/DCWL Classic Chimney & DTWN Tall Traditional Wall Hoods) -/ x /4 (.8 cm) x (.9 cm) wood strip -/6 (4.6 cm) 5/6 nut driver Slot for wood strip 5/6 nut driver 5 6 Measure down -/6 (4.6 cm) from desired height of hood and secure -/ x /4 wood strip (not included) wall using screws provided. 5/6 nut driver Use additional mounting screws secure hood wood strip. 5/6 nut driver Slide spacer front over front lip. Push spacer rear up, then slide back over rear lip. Slide filter front over front lip. Push filter rear up, then slide back over rear lip. Duct Cover Option (DCWH/DCWN/DCWL Classic Chimney Wall Hoods) CUTION: Secure vent hood wall using screws provided. Make sure mounting screws are secured in frame. Use additional mounting screws and wall anchors, if necessary. CUTION: If not using a duct cover, using screws provided make sure p mounting screws are secured in soffit or cabinet frame. Use additional mounting screws, if necessary. Measure distance from ceiling canopy. Tape avoid scratching

24 4 5/6 nut driver Place duct cover p inside duct cover base and lower until desired height is found. Mark height. Use the retaining nuts and bolts fasten in place from inside and remove tape. Slide duct cover in place and fasten from inside canopy using the sheet metal screws provided. Duct Cover Option (DTWN Tall Traditional Wall Hoods) Insert 6 of electrical wiring through the p of vent hood and secure using wiring restrain. Refer local codes. CUTION: Using screws provided secure vent hood wall. Make sure mounting screws are secured in frame. Use additional mounting screws and wall anchors, if necessary. 4 RE OR GREEN WHITE GREEN LCK WHITE LCK 5/6 nut driver Measure distance from ceiling canopy. Installation (DTWS Slim Traditional) Slide duct cover in place and fasten from inside canopy using the sheet metal screws provided. CUTION: If not using a duct cover, using screws provided make sure p mounting screws are secured in soffit or cabinet frame. Use additional mounting screws, if necessary. Connect black black, white white, and the green/bare wire under the green screw. NOTE: Housing wiring must be properly installed for wiring be correct when wiring unit. W R N I N G TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, OR INJURY TO PERSONS, OSERVE THE FOLLOWING Use this unit only in the manner intended by the manufacturer. If you have any questions, contact the manufacturer. efore servicing or cleaning unit, switch power off at service panel and lock service panel prevent power from being switched on accidentally. When the service disconnecting means cannot be locked, securely fasten a prominent warning device, such as a tag, the service panel. 5 To install ventillation kit refer ventillation kit installation instructions. Flip hood over. Remove electrical box cover. Replace electrical box cover. Make connection breaker box

25 6 7 4 Slide filter front over front lip. Push filter rear up, then slide back over rear lip. Slide spacer front over front lip. Push spacer rear up, then slide back over rear lip. NOTE: Number of spacers and baffles may vary by model. Place duct cover p inside duct cover base and lower until desired height is found. Mark height. Use the retaining nuts and bolts fasten in place from inside and remove tape. Slide duct cover in place and fasten from inside canopy using the sheet metal screws provided. 8 Slide filter front over front lip. Push filter rear up, then slide back over rear lip. Duct Cover Option (DTWS Slim Traditional Wall Hoods) Measure distance from ceiling canopy. Tape avoid scratching

26 Installation (DCIH Classic Chimney Island Hoods) 4 5/6 nut driver Check framing where cuut will be. NOTE: 00 lb. limit. Cut appropriate size hole in ceiling. Either 7 or 0 depending on your specific unit and ventilar kit. Run duct work down botm edge of duct cover/soffit and secure in place. Make sure the duct does not stick down past the cover. ttach canopy duct cover/soffit. From inside of hood, seal p of hood duct with aluminum tape. Mounting options: 5 Using duct cover with ceiling mounting bracket. (Option ) Using threaded rod for additional support. (Option ) ttaching hood directly soffit or duct cover. (Skip step ) To install ventillation kit refer ventillation kit installation instructions. NOTE: It is recommended follow option or, however both aren t necessary. ttach duct cover optional ceiling mounting bracket. Slide filter front over front lip. Push filter rear up, then slide back over rear lip. 5/6 nut driver 6 7 ttach duct cover ceiling. The ceiling bracket can be hidden by using a locally supplied trim. dditional support option. Drill holes in all four corners for threaded rod and run rods from hood ceiling. Slide spacer front over front lip. Push spacer rear up, then slide back over rear lip. NOTE: Number of spacers and baffles may vary by model. Slide filter front over front lip. Push filter rear up, then slide back over rear lip. 50 5

27 Service & Registration Service & Parts Only authorized replacement parts may be used in performing service on the appliance. Do not repair or replace any part of the appliance unless specifically recommended in the manual. ll other servicing should be referred a qualified technician. Record the following information indicated below. You will need it if service is ever required. The serial number and model number for your appliance are located on the identification plate mounted on the inside of the hood canopy. Model number Serial number Date of purchase Date installed Dealer's name ddress 5 5

28 54 55