CETAC Z-Drive Nylon Cable
|
|
- Gabriella Morton
- 5 years ago
- Views:
Transcription
1 CETAC Z-Drive Nylon Cable Installation Guide Manual Part Number rev2, Teledyne Technologies Inc, Printed in USA
2 Overview This guide describes how to replace the nylon line which operates the autosampler Z-drive assembly. These instructions apply to many CETAC autosamplers. The appearance of your Z-drive may differ from what is shown in this document. Tools Required You will need the following tools: Small flathead screwdriver. Wire cutters, for trimming the cable. Small needle-nose pliers for removing the old cable. Tape measure. You can remove thumbscrews with tools if necessary, but do not tighten them with anything other than your fingers. CAUTION Do not allow the cable to bend sharply. Avoid pushing up on the probe bracket (zaxis slider) or pushing on the Z-drive cable. Doing so can kink the cable, in which case the cable must be replaced. Replacing the Cable WARNING Ensure the power turned off before proceeding with installation. 1 Place the autosampler on a flat surface and turn the unit off. Figure 1 Front view of ASX-520 autosampler. 2
3 2 Remove the old PEEK or nylon cable from the rotor by loosening the thumbscrew on the rotor. Figure 2. Removing cable from rotor. 3 Remove new cable from the packaging. 4 On the slider, cut the old cable or peek tubing in the exposed opening. Figure 3. Cutting the old cable. 3
4 5 Use needle nose pliers to slide the old cable out of the Z-axis drive assembly. Figure 4. Removing the old Z-drive tubing. 6 Slide in the cable and using the tape measure, cut to 43 inches, until it reaches the slider. Push the cable into the slider, guiding it through the second hole until it comes out of the bottom of the slider. Figure 5. Sliding in the new cable. Figure 6. Sliding the cable through completely. 4
5 7 Use the small flat head screwdriver to wedge between the slider opening and the new cable. Turn the screwdriver 90 degrees to form a bend in the cable. This permanent bend will hold the cable in place on the Z-drive slider. Figure 7. Affixing the cable to the slider. Figure 8. View of bent cable. 8 Cut the excess exposed cable on the bottom of the slider. Figure 9. Removing excess cable. 5
6 9 Feed the cable through the rear guide block, then tighten the PEEK nut to secure it. Figure 10. Tighten PEEK nut for cable casing adjustment. 10 Turn the rotor clockwise as far as it will go. Rotor Pin Stator Stop Figure 11. View of rotor with rotor pin at stator stop. 6
7 11 Slide the cable onto the rotor on the back of the autosampler (Error! Reference source not found.4). If needed, loosen the thumbscrew on the rotor to allow the cable to pass through the clamp. Figure 12. Sliding Z-drive cable into rotor groove. 12 Gently move the Z-axis slider until the gap between the slider and cap is approximately 3/32 (~2mm). 3/32 (~2mm) Figure 13. View of gap between probe bracket and cap. 7
8 13 Center the Y-arm tube in the autosampler X-travel slot in order to properly adjust the drive cable. This step applies to all models of ASX-500 series autosamplers. X-travel slot Figure 14. Arm centered for cable casing adjustment. Figure 15. Proper cable orientation. 8
9 14 Hold the cable flat against the rotor and secure the cable by tightening thumbscrew on the rotor. Maintain the 3/32 (~2mm) gap while the rotor pin is making contact with the stator stop (full clockwise rotation of rotor). The thumbscrew should be as tight as possible using just your fingers. Figure 16. Securing cable to rotor. 15 Rotate the rotor back and forth to ensure that it moves freely. Ensure that the full width of the cable is under the clamp. Clamp Figure 17. Verifying cable movement and cable clamp. 9
Automated Liquid Handling Station
Automated Liquid Handling Station Quick Installation Guide Manual Part Number 32-0406-048 Rev 0 COPYRIGHT 2018 Teledyne Technologies Incorporated. All rights reserved. 32-0406-048 Rev 0, May, 2018 Printed
More informationXLR-8 60 Extended Rack Autosampler
XLR-8 60 Extended Rack Autosampler Quick Installation Guide Manual Part Number 480226 Rev 0 COPYRIGHT 2015 Teledyne Technologies Incorporated. All rights reserved. 480226 Rev 0, October, 2015 Printed in
More informationXLR-8 EXTENDED RACK ACCESSORIES AND PARTS CATALOG
XLR-8 EXTENDED RACK ACCESSORIES AND PARTS CATALOG Catalog part number 620108 Rev 1, August, 2018 Accessories and Supplies Tray XLR-8 SP7025 Z-Axis Drive Assembly PEEK Anti Kink SP7171 For use with Carbon
More informationShaver Industries. Assembly Instructions Vertical Vinyl Curtain Door DT2 Wire Rope Replacement
Shaver Industries 20 Steckle Place, Kitchener, ON N2E 2C3 Ph 1(888) 766 8328 www.shaverinc.com Assembly Instructions Vertical Vinyl Curtain Door DT2 Wire Rope Replacement Overview: Preparation: Installation:
More informationCarousel Unit User Manual Replacing the Check Stand Motor
Carousel Unit User Manual Replacing the Check Stand Motor 02/01/2017 1 Table of Contents Tools:... 3 Turn Off Power to the Unit:... 4 Remove Power Switch... 5 Remove Electric Eyes:... 6 Remove POS (Point-Of-Sale)
More informationSupply Valve Replacement
This procedure is to help facilitate the replacement of the25.1-25.4 supply valves. Solenoid Supply Valves Note: You will need the following tools: Socket Wrench with extension and a 3/8 Socket Size 1
More informationENC-560 Autosampler Enclosure
ENC-560 Autosampler Enclosure Installation Guide Manual Part Number 480232 Rev 1 COPYRIGHT 2016, 2017 Teledyne Technologies Incorporated. All rights reserved. 480232 Rev 1, June, 2017 Printed in USA. Teledyne
More informationS6 BATTERY REPLACEMENT
S6 BATTERY REPLACEMENT Supplemental Instruction Guide P/N 108304 Battery Pack Removal Tools Required: S6 Operation & Parts Manual, Phillips Head Screwdriver, Needle Nose Pliers, Wire Stripping / Crimping
More informationCenter Drive Tube. Gussets
O P E R A T O R S M A N U A L EZ-GLIDE SYSTEM ALUMINUM DROP DOWN LADDER RACK Read and understand all WARNINGS, DANGERS, NOTICES and instructions before assembly and installation. WARNING MODEL 251-3-02,
More informationXLR-8 60 Extended Rack Autosampler
XLR-8 60 Extended Rack Autosampler ACCESSORIES AND PARTS CATALOG Catalog part number 620131 Rev 4, June 2018 Accessories and Supplies Sample Probes Length: 10 inches (25.4 cm) Probe Material: FEP-covered
More informationGENUINE PARTS INSTALLATION INSTRUCTIONS
GENUINE PARTS INSTALLATION INSTRUCTIONS 1. 2. 3. 4. DESCRIPTION: APPLICATION: PART NUMBER: KIT CONTENTS: Accent light Kit Versa Note 999F3 4Z000 - Accent Lighting Kit. 999Q9 AY000 - Accessory Service Connector
More informationGENUINE PARTS INSTALLATION INSTRUCTIONS
GENUINE PARTS INSTALLATION INSTRUCTIONS 1. 2. 3. 4. DESCRIPTION: APPLICATION: PART NUMBER: KIT CONTENTS: Security light Kit Maxima 999F4 AX009 - Universal Security Lighting Kit. Item QTY Description Service
More information401B/1KDB CoolRite/FreezeRite Installation Manual I003
401B/1KDB CoolRite/FreezeRite Installation Manual 99-16105-I003 Copyright 2011 by ALL rights reserved. Information in this document is subject to change without notice. Companies, names and data used in
More informationInstallation Manual TWM Performance Short Shifter Cobalt SS/SC, SS/TC, HHR SS, Ion Redline and Saab 9-3
Page 1 Installation Manual TWM Performance Short Shifter Cobalt SS/SC, SS/TC, HHR SS, Ion Redline and Saab 9-3 Please Note: It is preferable to park on a flat surface, as you will have to engage and disengage
More informationOPTIMAX RADIANT FIELD RETROFIT INSTRUCTIONS
OPTIMAX RADIANT FIELD RETROFIT INSTRUCTIONS 99-24283-I001 Table of Contents 1. 24V LED Approved Drivers 5 1.1. 24V LED Driver (60-19910-0002).. 5 2. Optimax Radiant 24V LED Lighting. 6 2.1. OP30 6 2.2.
More informationFlexJet - Flex Cable Replacement
P/N: 109515R0 14140 NE 200th St. Woodinville, WA. 98072 PH: (425) 398-8282 FX: (425) 398-8383 FlexJet - Flex Cable Replacement Notices: Warning! Ensure that all AC power cables are removed from the printer
More informationGENUINE PARTS INSTALLATION INSTRUCTIONS
GENUINE PARTS INSTALLATION INSTRUCTIONS 1. 2. 3. 4. DESCRIPTION: Security Light Kit APPLICATION: Altima Coupe and Sedan (2011+) PART NUMBER: 999F4 AX008 - Universal Security Lighting Kit. KIT CONTENTS:
More informationGENUINE PARTS INSTALLATION INSTRUCTIONS
GENUINE PARTS INSTALLATION INSTRUCTIONS 1. 2. 3. 4. DESCRIPTION: Security Light Kit APPLICATION: Altima Sedan (2013+) PART NUMBER: 999F4 AX010 - Universal Security Lighting Kit. KIT CONTENTS: Item QTY
More informationSEAL REPLACEMENT SeaStar ATM, Inboard Steering Cylinders, -3 Models
Copy Part# 343321, Rev. D, 05/2015 Page 1 of 6 SEAL REPLACEMENT SeaStar ATM, Inboard Steering Cylinders, -3 Models CAUTION Applicable Cylinders Throughout this publication, Warnings and Cautions (accompanied
More information2003 CR-V - A/T Shift Cable Replacement-Print Preview
Page 1 of 7 2003 CR-V - A/T Shift Cable Replacement 1. Raise the front of the vehicle, or lift the vehicle up, and make sure it is securely supported. 2. Remove the driver's dashboard lower cover, and
More information* * APPLICABLE MODELS: 2014 > Mazda 3
PART NUMBER: 0000 8C L48 (DIO) / 0000 89 L84 (PIO) GENUINE ACCESSORIES INSTALLATION INSTRUCTIONS Rev. AAA *550-0700-000* APPLICABLE MODELS: 2014 > Mazda 3 REQUIRED COMPONENTS: ITEM QTY DESCRIPTION Usage
More informationSeal Replacement Steering Cylinders Model Numbers: HC & HC5329-3
Copy Part# 343337, Rev. A, 01/2011 Page 1 of 6 Seal Replacement Steering Cylinders Model Numbers: HC5328-3 & HC5329-3 Throughout this publication, Warnings and Cautions (accompanied by the International
More informationInstallation Instructions for the EVO3 Height-Adjustable Ultimate Short Shifter. for F80 M3 and F82 M4
Installation Instructions for the EVO3 Height-Adjustable Ultimate Short Shifter for 2013+ F80 M3 and F82 M4 part number USSF80 Thank you for purchasing the Ultimate Shift Kit. Please read these directions
More informationReplacing the X Axis Belt
Overview This Document is designed to guide you through replacing the X axis belt on your Epilog Zing laser Engraver. Requirements: Tools: Replacing the X Axis Belt For the Epilog Zing Laser Engraver Revision
More information* * APPLICABLE MODELS: 2014 > Mazda 6
PART NUMBER: 0000 8C H02(DIO) / 0000 89 H18(PIO) GENUINE ACCESSORIES INSTALLATION INSTRUCTIONS Rev. AAA *550-0694-000* APPLICABLE MODELS: 2014 > Mazda 6 REQUIRED COMPONENTS: ITEM QTY DESCRIPTION Usage
More information* * APPLICABLE MODELS: 2017 > CX-5
PART NUMBER: 0000 8C R06(DIO) / 0000 89 R28(PIO) GENUINE ACCESSORIES INSTALLATION INSTRUCTIONS Rev. AAA *550-0681-000* APPLICABLE MODELS: 2017 > CX-5 REQUIRED COMPONENTS: ITEM QTY DESCRIPTION Usage Chart
More informationInstallation Instructions for the EVO3 Height-Adjustable Ultimate Short Shifter
Installation Instructions for the EVO3 Height-Adjustable Ultimate Short Shifter for 1992-2005 325, 323, 318 and 1986-1994 525, 528, 535, 540 5-speed models only. (part number USSE3 and USSE5) Thank you
More informationHow to Replace a Switch
How to Replace a Switch The switches are the ones most frequently replaced, either because a switch has failed or because you want to substitute a newer type. Before deciding that a switch has failed,
More information* * APPLICABLE MODELS: 2016 > CX-3
PART NUMBER: 0000 8C S01(DIO) / 0000 89 S07(PIO) GENUINE ACCESSORIES INSTALLATION INSTRUCTIONS Rev. AAA *550-0688-000* APPLICABLE MODELS: 2016 > CX-3 REQUIRED COMPONENTS: ITEM QTY DESCRIPTION Usage Chart
More informationUtah Soaring Association Rigging and De-Rigging. USA G-103 Twin II. Procedures for safe assembly and dis-assembly of the glider. (Trailers 1, 2 and 3)
USA G-103 Procedures for safe assembly and dis-assembly of the glider (Trailers 1, 2 and 3) Grob Glider Rigging Tools Required: Large blade standard screwdriver #2 (medium blade) Phillips screwdriver (if
More informationGENUINE ACCESSORIES INSTALLATION INSTRUCTIONS. ITEM QTY DESCRIPTION Usage Chart Service Part Number. 1 1 Mirror Assembly w/ Compass 1
AUTO PART NUMBER: 0000 8C P4 (DIO)/ 0000 89 P25 (PIO) REQUIRED COMPONENTS: INSTALLATION KIT: 2 SA Harness - 2 Conductor 3 0 Wire Ties 4 Wire Cover 5 A-Pillar Tether Clip (D09W-6862) 6 3 Foam Tape 7 3 Electro-Tap(wire
More informationCurrent Range Rover Sport STRUT Collection Installation Manual
2014 - Current Range Rover Sport STRUT Collection Installation Manual 1 1. Removing Main Grille and Lower Fascia 1.1 Run a line of low tack masking tape across the front of the bumper below the grille
More informationFIXTURE INSTALLATION GUIDE Model T21T (Low Voltage Pendant Set 120V)
FIXTURE INSTALLATION GUIDE Model T21T (Low Voltage Pendant Set 120V) 21T, Rev.4 6-13 IMPORTANT: Before proceeding, retrieve the GLASS SHADE INSTALLATION GUIDE, which is included with the pendant cord set
More informationSIDI Camshaft Position Actuator Replacement
BLOCK AND WEDGE TIMING CHAIN RETAINER USER GUIDE SIDI Camshaft Position Actuator Replacement Removal Procedure 1. Remove the camshaft cover. 2. Remove the camshaft position actuator solenoid valve solenoid
More information8. Electronics assembly (B3/R2 design)
8. Electronics assembly (B3/R2 design) Written By: Jakub Dolezal 2018 manual.prusa3d.com/ Page 1 of 31 Step 1 Tools necessary for this chapter Needle-nose pliers for zip tie trimming. 2.5mm Allen key for
More informationInstructions for repairing the F-Body Hatch Pull-Down Unit By Lon Salgren (ls90rs)
Instructions for repairing the 1986-87 F-Body Hatch Pull-Down Unit By Lon Salgren (ls90rs) Lonsal@adelphia.net CAUTION: Completely read and understand the instructions before proceeding. There are some
More informationAir Conditioner for M915 A0/A1 Truck
RD-2-4530-0 Air Conditioner for M915 A0/A1 Truck INSTALLATION INSTRUCTIONS Install refrigerant compressor per instructions provided with compressor mount kit. CAUTION: Edges of sheet metal can be sharp!
More informationMobtown Offroad Toyota Tacoma Bolt On Rock Slider Installation Instructions
Mobtown Offroad 2005+ Toyota Tacoma Bolt On Rock Slider Installation Instructions Tools Needed: 9/16 Box Wrench 9/16 Standard and Deep Well Socket, 3/8 Drive Ratchet, 3/8 Drive 3/4 Standard Socket 3/4
More informationACCESSORIES AND PARTS CATALOG
ASX-280 AUTOSAMPLER ACCESSORIES AND PARTS CATALOG Catalog part number 620130 Rev 7, February 2018 Accessories and Supplies Sample Probes Length: 10 inches (25.4 cm) Probe Material: FEP-covered carbon fiber
More informationACCESSORIES AND PARTS CATALOG
ASX-560 AUTOSAMPLER ACCESSORIES AND PARTS CATALOG Catalog part number 620127 Rev 9, February 2018 Accessories and Supplies Sample Probes Length: 10 inches (25.4 cm) Probe Material: FEP-covered carbon fiber
More informationGENUINE PARTS INSTALLATION INSTRUCTIONS
GENUINE PARTS INSTALLATION INSTRUCTIONS 1. 2. 3. 4. DESCRIPTION: APPLICATION: PART NUMBER: KIT CONTENTS: Accent light Kit Pathfinder 999F3 XZ000 - Accent Lighting Kit. Item QTY Description Service Part
More informationService Information Chevrolet Camaro 3.6L LFX Engine. Camshaft Position Actuator Replacement - Bank 1. Document ID:
Service Information 2014 Chevrolet Camaro 3.6L LFX Engine Camshaft Position Actuator Replacement - Bank 1 Document ID: 2900815 Special Tools Removal Procedure EN49982-1 Timing Chain Retainer EN49982-2
More informationTOYOTA TACOMA EC REARVIEW MIRROR Preparation
Preparation Part Number: PT374-35052 Kit Contents Item # Quantity Reqd. Description 1 1 AD Mirror Assembly 2 1 Hardware bag Hardware Bag Contents Item # Quantity Reqd. Description 1 1 T-tap Connectors,
More informationSouthwest Windpower Instruction Sheet AIR-X Circuit Replacement Kit
Southwest Windpower Instruction Sheet AIR-X Circuit Replacement Kit Tools Required 5 / 32 Hex key 5 / 16 Hex key 7 / 64 Hex key Standard screwdriver Pair of external snap ring pliers Rubber mallet Hammer
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS REAR DISC BRAKE CONVERSION KIT A126-1 1973-87 CHEVROLET 1/2 TON 2WD Thank you for choosing STAINLESS STEEL BRAKES CORPORATION for your braking needs. Pleases take the time to
More informationFIXTURE INSTALLATION GUIDE Model T21T (Low Voltage Pendant Set 120V)
FIXTURE INSTALLATION GUIDE Model T21T (Low Voltage Pendant Set 120V) 21T, Rev.4 6-13 IMPORTANT: Before proceeding, retrieve the GLASS SHADE INSTALLATION GUIDE, which is included with the pendant cord set
More informationInstallation Instructions COMPETITION/PLUS SHIFTER Ford Mustang MT82 6-Speed Manual Transmission Catalog#
Installation Instructions COMPETITION/PLUS SHIFTER 2015-2017 Ford Mustang MT82 6-Speed Manual Transmission Catalog# 3916037 Rev. 00 WORK SAFELY! For maximum safety, perform this installation on a clean,
More information3M Overhaul Service Kit
SERVICE INSTRUCTIONS FOR 3M 12,000 RPM 3 in. (77 mm) RANDOM ORBITAL SANDERS 3M Overhaul Service Kit The part number 20346, 3M Overhaul Service Kit, contains all the replacement parts that naturally wear
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS REAR DISC CONVERSION KIT A126-2 1988-98 C1500 2WD 10" REAR DRUM Thank you for choosing STAINLESS STEEL BRAKES CORPORATION for your braking needs. Pleases take the time to read
More informationLIPPERTCOMPONENTS, INC.
LIPPERTCOMPONENTS, INC. SCHWINTEK INWALL SLIDEOUT SYSTEM OPERATION AND SERVICE MANUAL Contents I. Controls 1-1 System components 1 1-1A versions C1 & C2 2 1-2 Motor wiring harness connections 3 1-3 Extend
More informationKHR Series Regulators
KHR Series Regulators Maintenance Instructions Kit Contents retainer Poppet Poppet spring Poppet damper Outer body seal Inner body seal Upper piston seal seal backup ring Main piston seal vent seal Self-vent
More informationLPE C5 Battery Relocation Kit
LPE C5 Battery Relocation Kit The LPE C5 Corvette battery relocation kit improves vehicle weight distribution by moving weight to the rear of the vehicle. The improved weight distribution increases traction
More information5. E-axis assembly. 5. E-axis assembly. Written By: Jakub Dolezal manual.prusa3d.com/ Page 1 of 40
5. E-axis assembly Written By: Jakub Dolezal 2018 manual.prusa3d.com/ Page 1 of 40 Step 1 Tools necessary for this chapter Needle-nose pliers for zip tie trimming. 2.5mm Allen key for M3 screws 2mm Allen
More informationFIXTURE INSTALLATION GUIDE Model T21T (Low Voltage Pendant Set 120V)
FIXTURE INSTALLATION GUIDE Model T21T (Low Voltage Pendant Set 120V) 21T, Rev.4 6-13 IMPORTANT: Before proceeding, retrieve the GLASS SHADE INSTALLATION GUIDE, which is included with the pendant cord set
More informationGENUINE PARTS INSTALLATION INSTRUCTIONS
GENUINE PARTS INSTALLATION INSTRUCTIONS DESCRIPTION: APPLICATION: PART NUMBERS: Sports Horn Murano / Murano Cross Cabriolet (2011) Sports Horn (B5610 1SXOA) KIT CONTENTS: Item QTY. Description Part Number
More informationInstallation Guide. Kennedy Technology Group, Inc.
Installation Guide Harley-Davidson Amp Module - Base Kit Kennedy Technology Group, Inc. 614 Ridgeway, Rose Hill, Kansas 67133 - USA voice 316.776.1111 fax 316.776.9035 email:kennedy@cellset.com www.cellset.com
More informationFIXTURE INSTALLATION GUIDE Model T21T (Low Voltage Pendant Set 120V)
FIXTURE INSTALLATION GUIDE Model T21T (Low Voltage Pendant Set 120V) 21T, Rev.4 6-13 IMPORTANT: Before proceeding, retrieve the GLASS SHADE INSTALLATION GUIDE, which is included with the pendant cord set
More informationRollstar Shade Installation Instructions
Rollstar Shade Installation Instructions All Lifting Systems Inside or Outside Mount Thank you for purchasing your new Rollstar shade. It has been custom-made from the highest quality materials to the
More informationFluid-O-Tech ROTOFLOW ROTARY VANE PUMP REBUILD MANUAL
Fluid-O-Tech PUMP TECHNOLOGY AT ITS BEST WWW.FLUID-O-TECH.COM Office: 161 Atwater St., Plantsville, CT 06479 Phone: (860) 276-9270 Fax: (860) 620-0193 ROTOFLOW ROTARY VANE PUMP REBUILD MANUAL 08/09 Ed.,
More informationSetup, Assembly, & Adjustment
Setup, Assembly, & Adjustment 34877 Rev. B 1 of 8 Melco Fast Clamp Instructions The Melco Fast Clamp is a versatile clamping system for your embroidery machine. This document will walk you through the
More informationConflicts: Vehicles without a sunroof Vehicles with a single sunroof
Toyota Sienna (Dual Sunroof) 2011-10.2 Overhead Video Part Number: 00016-00110 00016-00110-17 Fit Kit 00016-00120 00016-00120-17 Fit Kit Accessory Code: ED5 Conflicts: Vehicles without a sunroof Vehicles
More information3. Extruder Assembly
3. Extruder Assembly Guide for the assembly of the Extruder. Written By: Josef Prusa 2017 manual.prusa3d.com Page 1 of 22 Step 1 Get the necessary tools 2.5 and 1.5 mm Allen key Needle-nose pliers Step
More informationShimano Trinidad\Torium Drag Upgrade Tutorial
Shimano Trinidad\Torium Drag Upgrade Tutorial Introduction: This tutorial is provided to assist those of you who may be interested in performing upgrade of the drag system of your Shimano Trinidad 16,
More informationMishimoto Performance Aluminum Mustang Radiator - Manual - (94-95 GT/Cobra/V6) - Installation Instructions
Mishimoto Performance Aluminum Mustang Radiator - Manual - (94-95 GT/Cobra/V6) - Installation Instructions The below installation instructions work for the following products: Mishimoto Performance Aluminum
More informationDISCONTINUED. Installation. Aerada 900 Series Futura Faucet. With Accu-Zone (AZ) Infrared Control
Aerada 900 Series Futura Faucet With Accu-Zone (AZ) Infrared Control BRADLEY SC A S53-141 4" Centerset S53-148 4" Centerset, no Solenoid Valve S53-186 4" Centerset with 8" Trim Plate S53-285 Centershank
More informationZ-Truck (Vertical Moving) Z-truck Flag. Y-Truck (Horizontal Moving) FIGURE 1: VIEW OF THE Z-TRUCK. Flexshaft Assembly
Checking and Replacing the AC Motor To remove and replace the AC Motor you will need the following tools: #2 Phillips screwdriver (magnetic tip preferred) Removing the AC Motor 1. Ready the machine by
More information<THESE INSTRUCTIONS MUST BE GIVEN TO THE END USER> B&W Trailer Hitches 1216 Hawaii Road / PO Box 186 Humboldt, KS P: F:
B&W Trailer Hitches 26 Hawaii Road / PO Box 86 Humboldt, KS 6678 P:620.73.366 F:620.869.903 RAM OEM Mount System Installation Instructions 25,000 LBS.
More informationM GT 2005 up Mustang ENGINE START Push-Button INSTRUCTION SHEET
Please contact the Ford Racing Techline for the most current instruction information @ (800) FORD-788!!! PLEASE READ THE FOLLOWING INSTRUCTIONS CAREFULLY PRIOR TO INSTALLATION!!! OVERVIEW: The following
More informationTOYOTA SOLARA EC REARVIEW MIRROR Section I - Installation Preparation
Section I - Installation Preparation Part Number: PT374-33020 Section I - Installation Preparation Kit Contents Item # Quantity Reqd. Description 1 1 AD Mirror Assembly w/compass 2 1 Hardware Bag 3 1 Installation
More information<THESE INSTRUCTIONS MUST BE GIVEN TO THE END USER> B&W
B&W Trailer Hitches 6 Hawaii Rd / PO Box 86 Humboldt, KS 66748 P:60.473664 F:60.869.903 Turnoverball Gooseneck Hitch Installation Instructions MODEL 08
More informationPARTS TOOLS. Set Screw. Washer (2) Blue Bushing (2) Black Bushing (2) B&M Short Throw Shifter. Jam Nut Grease. Retaining Ring (2) Insert (2)
Installation Instructions SHORT THROW SHIFTER Fits: Porsche Boxter, Boxter S, 911, 996 Cayman & Cayman S models See Application Guide for specific year ranges and engine sizes Catalog # 45135 WORK SAFELY!
More informationWARNING NOTICE CAUTION ASSEMBLY INSTRUCTIONS
MODEL 284 EZ-GLIDE SYSTEM 10' HIGH CUBE VAN DRIVER SIDE ALUMINUM DROP DOWN LADDER RACK ATTENTION Read and understand all instructions and warnings before operating or using this product. WARNING This product
More informationGENUINE PARTS INSTALLATION INSTRUCTIONS
GENUINE PARTS INSTALLATION INSTRUCTIONS 1. 2. 3. 4. DESCRIPTION: Accent light Kit APPLICATION: Infiniti JX (2013) PART NUMBER: 999F3 YY000 - Universal Accent Lighting Kit. KIT CONTENTS: Item QTY Description
More informationFiber Connector Shelf (CCS)
Corning Cable Systems Standard Recommended Procedure (SRP) 003-595 Issue 3, May 2007 Page 1 of 6 Fiber Connector Shelf (CCS) Table of Contents 1. General... 1 2. Precautions... 1 3. Components... 2 4.
More informationMaintenance Information
16572679 Edition 2 May 2014 Air Drill QP Series Maintenance Information Save These Instructions Product Safety Information WARNING Failure to observe the following warnings, and to avoid these potentially
More informationFinal Assembly Instructions Portside Cruiser
Final Assembly Instructions Portside Cruiser Thank you for buying your new bicycle from L.L.Bean. Read these instructions carefully before beginning the final assembly. Prior to shipping, our expert cycling
More informationSecond Stage Regulator - 1/4 Turn
Second Stage Regulator - 1/4 Turn MAINTENANCE AND REPAIR TAL 806 (L) Rev. 6 MSA 2008 Prnt. Spec. 10000005389 (I) Mat. 10042827 Doc. 10000015245 1/4 TURN SECOND STAGE REGULATOR SECOND STAGE REGULATOR COMPONENTS
More informationWOC & WOC Top & Back Installation Instructions
Shown with optional Sun Roof WOC-900500-2 & WOC-900501-2 Top & Back Installation Instructions Install Order! Heater Door System Wiper on to Windshield Windshield Rear Panel Top Panel Tools needed: 5/16
More information3M Overhaul Service Kit
SERVICE INSTRUCTIONS FOR 3M 12,000 RPM 5 in. (127 mm) and 6 in. (150 mm) RANDOM ORBITAL SANDERS 3M Overhaul Service Kit The part number 20347, 3M Overhaul Service Kit, contains all the replacement parts
More informationHow to install shifter style lever (Gen 1 & Gen
How to install shifter style lever (Gen 1 & Gen 2) Written By: The Hive 2017 service.bythehive.com Page 1 of 10 TOOLS: T25 Torx wrench (1) Cable cutter (1) M3 Hex wrench (1) 2017 service.bythehive.com
More information3D PRINTER. Pack 09. Anything you can imagine, you can make! 3D technology is now available for you at home! BUILD YOUR OWN
BUILD YOUR OWN Pack 09 Anything you can imagine, you can make! 3D PRINTER Compatible with Windows 7 & 8 Mac OS X 3D technology is now available for you at home! www.model-space.com BUILD YOUR OWN 3D PRINTER
More informationLEXUS RC 350/RC-F ILLUMINATED DOOR SILLS Preparation
Preparation Part Number: PT944-24150 Kit Contents Item # Quantity Reqd. Description 1 2 Inner LED Scuff 2 2 Outer Scuff 3 1 Hardware Bag Hardware Bag Contents Item # Quantity Reqd. Description 1 15 20
More informationB&W Trailer Hitches 1216 Hawaii Road / PO Box 186 Humboldt, KS P: F:
B&W Trailer Hitches 1216 Hawaii Road / PO Box 186 Humboldt, KS 66748 P:620.473.3664 F:620.869.9031 NOTE: We recommend reading instructions before beginning the installation. Ford OEM Mount System Slider
More informationSignal Mirror Installation Instructions
Signal Mirror Installation Instructions Chevy Blazer 1992-1994, Chevy Suburban 1992-1999, Chevy Tahoe 1995-1999, Chevy Tahoe Limited 2000, GMC Suburban 1992-1999, GMC Yukon 1992-1999, GMC Yukon Denali
More informationValve Box and Valve Accessories G4315A, G4316A, G4317A
Valve Box and Valve Accessories G4315A, G4316A, G4317A Installation Guide The G4315A, G4316A, and G4317A accessories consist of separate kits depending on the custom configuration ordered. These kits may
More informationPhoto 1. Shift pattern gate plate
Installation Instructions MAGNUM GRIP STREET BANDIT SHIFTER Fits: GM, Chrysler, and Ford Automatic Transmissions See Application Guide for Specific Vehicles Catalog # 81050 WORK SAFELY! For maximum safety,
More informationWARNING! THIS PRODUCT MUST BE INSTALLED BY A TRAINED, AUTHORIZED RICON SERVICE TECHNICIAN.
II. INSTALLATION T he chapter provides instructions for installing the RICON RDO2900 Series Internal Power Swing Door Operator into full-size 1992 and later Ford vans, 1990 and later Chevrolet & GMC vans,
More informationPretium Wall-Mountable Housing (PWH-02P/-04P/- 06P/-12P and FZB-02P-JB)
1. Precautions 2. Carton Contents Pretium Wall-Mountable Housing OR Fiber Zone Box (FZB-02P-JB) PWH-02P and FZB-02B-JP have: (15 inches) edge grommet (1) Laser warning label (2) Fiber identification labels
More informationP4 CHAINSTAY INTEGRATED ROCKER BRAKE (CSIRB) INSTALLATION
P4 CHAINSTAY INTEGRATED ROCKER BRAKE (CSIRB) INSTALLATION TOOLS REQUIRED 2, 2.5, 3, 5 mm allen keys 8, 9 mm open faced cone wrench Pliers Cable cutters Torque wrench MATERIALS REQUIRED: 1 x P4 chainstay
More informationTOYOTA 4RUNNER CROSS BARS Preparation
Preparation Part Number: PT78-8970 Kit Contents Front Crossbar Assembly Rear Crossbar Assembly Hardware Bag Hardware Bag Contents Rubber Stopper 4 M6 Wafer Head Screw Load Label, 60kg 4 User Manual Additional
More information5 Removal and replacement
5 Removal and replacement This chapter describes the removal and replacement of field-replaceable units (FRUs) only. Removal and replacement strategy User-replaceable parts Covers Internal assemblies ENWW
More informationRekluse Motor Sports. The z-start Clutch CRF 250X. Installation Guide Copyright 2002 Rekluse Motor Sports z-start Revision RMS116 CRF 250X
Rekluse Motor Sports The z-start Clutch CRF 250X Installation Guide Copyright 2002 Rekluse Motor Sports z-start Revision 3.000 RMS116 CRF 250X 191-216 Manual Revision: 103105 Rekluse Motor Sports, inc.
More informationCoupler Mounted Bracket
Coupler Mounted Bracket INSTRUCTION MANUAL & GUIDELINES CMBA & CMBA M Issued October 2015 Please discard previous CMBA installation instructions CMB INSTRUCTIONS & GUIDELINES TABLE OF CONTENTS CMB Installation
More informationINSTALLATION INSTRUCTIONS FOR THE MOTOR TRIKE GL1500 RAKE KIT
INSTALLATION INSTRUCTIONS FOR THE MOTOR TRIKE GL1500 RAKE KIT Thank you for choosing the Motor Trike GL1500 Rake Kit. We ask that you read the directions before you start and follow them very closely.
More informationThe above explanation leaves out a few details, which may frustrate a user. Here are some instructions with pictures to help you be successful.
When the user exceeds the current capacity of the MY64 multimeter, an internal fuse opens to protect the precision current shunt. Typically this occurs when the user leaves the multimeter in current measuring
More informationFlexJet Carriage Circuit Board (PCB) Replacement
P/N: 111484 R0 14140 NE 200th St. Woodinville, WA. 98072 PH: (425) 398-8282 FX: (425) 398-8383 ioline.com FlexJet Carriage Circuit Board (PCB) Replacement Notices: Warning! Ensure that all AC power cables
More informationUSA G-103 Twin Astir
USA G-103 Procedures for safe assembly and dis-assembly of the glider (Trailers 2 and 3) Grob Glider Rigging Tools Required: Needle nosed pliers Wire cutters (side cut) Very large crescent wrench (for
More information5. SEPARATE STEERING INTERMEDIATE SHAFT ASSY (a) Fix the steering wheel with the seat belt. Release the 3 springs and separate the dust cover.
5119 OVERHAUL When installing, coat the parts indicated by the arrows with power steering fluid or molybdenum disulfide lithium base grease (See page 5116). 1. INSPECT CENTER FRONT WHEEL 510DA02 2. REMOVE
More informationIAG Air / Oil Separator (AOS) For STi
IAG Air / Oil Separator (AOS) For 2008-14 STi Part# IAG-ENG-7000 Tools Required: Ratchet, torque wrench, extensions, needle nose pliers, hose cutter, snips/scissors Sockets: 10mm, 12mm 13mm Wrenches: 10mm,
More informationInstallation For Service Only
For Service Only IMPORTANT! Aerada 1100 Series Low Arc Faucet S53-302 Battery Infrared Metering Faucet (Center Shank with 4" Trimplate) THIS SIDE UP! Packing List Read this entire installation manual to
More information