User Manual. (English)

Size: px

Start display at page:

Download "User Manual. (English)"

Harvey Jennings
5 years ago
Views:

1 User Manual (English)

2 Clean Handle is a door handle sanitizer designed to minimise spread of harmful germs in public environments. Contents 1. Installation 2. Inserting batteries 3. Inserting Aerosol 4. LED signals 5. Technical specifications 6. Warranty

3 1. Installation Clean Handle is mounted with the use of adhesive pads. On most door surfaces the device can be completely removed without leaving any mark. However, if the door surface is of delicate material, i.e. exclusive wood, Clean Handle cannot guarantee that removal of the device will not result in marks on the door. Before applying the device to the door ensure that the surfaces are clean, dry and unobstructed. Also check that the Clean Handle is compatible with the door handle by holding the device into approximate position. On mirror doors you may need to complement with extension pads.

4 1.1 Lateral markings Measure the distance between the edge of the door and the door handle plate (illus. 1). Using a pencil or tape, make a mark approx. 15 cm above the door handle plate and another 2-3 cm below. Illustration 1

1.2 Vertical markings Measure and mark a point 215 218 mm above the door

5 1.2 Vertical markings Measure and mark a point mm above the door handle (illus. 2). This is where the top of the device should be. Illustration 2

6 1.3 Check position Ensure that you have marked out the correct position by holding the device according to your marks. Do not remove the protective film from the adhesive pads when you do this. The device should be as close to the door handle plate as possible. 1.4 Mount the device Keeping the wall mount attached to the device, remove the protective film from the adhesive pads. Use the marks from step 1 and 2 to carefully position the device. Hold it firmly pressed against the door for five seconds.

7 1.5 Check the wall mount Open the top lid and pull the safety lock outwards from the door (illus. 3). Lift the device upwards and outwards (illus. 4). Remove the markings from the door and ensure that the adhesive pads have full contact with the door surface. Illustration 3

8 Illustration 4

9 2. Inserting Batteries When the batteries need changing this is indicated by a LED light next to the text LOW BATTERY on the device function panel. 2.1 Open the top lid and pull the safety lock outwards from the door (illus. 3). 2.2 Open the battery holder and insert four AA-batteries with the minus poles pointing towards the coils. Close the battery lid when done. 2.3 Reattach the device on the wall mount until it clicks into position. Ensure that the safety lock holds the device in position.

10 3. Inserting Aerosol When the aerosol needs changing this is indicated by a LED light next to the text LOW SPRAY on the device function panel. Note that the device only functions with Clean Handle s Aerosol Refill. 3.1 Open the top lid and turn the yellow lever to the side (illus. 5). Illustration 5

11 3.2 Hold the aerosol can with the bottom up and insert the container into the device (illus. 6). Illustration Gently press the container and pull the yellow lever over the bottom of the container (illus. 7).

Illustration 7 3.4 The device is now ready for use. It has two modes of operation (illus. 8).

12 Illustration The device is now ready for use. It has two modes of operation (illus. 8). Mode B: The device activates with one spray on the door handle 10 seconds after use, and an additional spray after another 15 seconds.

13 Illustration 8 To activate Mode A: Press and hold the power button until the LED shines with a constant green light. To activate Mode B: Press and hold the power button a second time until the LED blinks green. To power off: Press and hold the power button until the LED shines with a red light.

14 4. LED signals 4.1 Function panel Batteries: When the batteries need changing this is indicated by a LED light next to the text LOW BATTERY on the device function panel. Spray: When the aerosol needs changing this is indicated by a LED light next to the text LOW SPRAY on the device function panel. 4.2 Front LED The LED lights on the device casing activates 3 seconds before spray.

15 5. Technical specifications clean handle is made and developed in sweden Art. No. CH1_17 Batteries: 4 AA-batteries Material and coating: Anodized aluminium and plastic Measurements: Height 315mm, Width 58mm, Depth 45mm Media: Clean Handle Aerosol 75ml Pressure: 2,50 bar Spray rate: 0,7g/s Consumption: Approx sprays per container.

16 6. Warranty One year warranty from date of purchase.

LightRider. Instructions for Power Link Helmet Light. Helmet Vertical Midline

LightRider. Instructions for Power Link Helmet Light. Helmet Vertical Midline LightRider Instructions for Power Link Helmet Light Helmet Vertical Midline Look at the back of your helmet. Then imagine a vertical line that runs up the back and divides your helmet into right and left