ARPT. Multi-Position 1½ to 5 Tons Construction

Transcription

1 Multi-Position ½ to 5 Tons Air Handler with new SmartFrame Construction Standard Features Direct-drive, multi-speed motor Internal factory-mounted TXV valve Transformer and blower time-delay on all units All-Aluminum coil Easy single-bulb UV light compatibility Cabinet air leakage less than 2.0% at.0 inch H 2 O when tested in accordance with ASHRAE standard 93 Cabinet air leakage less than.4% at 0.5 inch H 2 O when tested in accordance with ASHRAE standard 93 AHRI Certified; ETL Listed Cabinet Features New rigid SmartFrame cabinet 2 depth for easy attic access Galvanized, leather grain-embossed finish Foil-faced insulation covers the entire blower case to reduce operating sound and cabinet condensation Glue-less cabinet insulation retention Screw-less sides & back prevents condensation Multi-position capability: upflow, downflow, horizontal or vertical Coil-mounting track for quick repositioning Tool-less filter access accommodates standard-size filters Easily convertible 4-way design Multiple electrical knockouts Heavy-gauge bottom plate Contents Nomenclature Dimensions...4 Airflow Data...5 Heat Kit Match-Ups...6 Wiring Diagram...7 Accessories...8 * Complete warranty details available from your local dealer or at To receive the 0-Year Parts Limited Warranty, online registration must be completed within 60 days of installation. Online registration is not required in California or Québec. SS-G 9/2 Supersedes 8/2

2 Nomenclature A R P T 8 B , AA,2 Brand Engineering * A Single- piece Major/ Minor Revisions Air Handler * Not used for inventory management Unit Applica3on Refrigerant Charge C Ceiling Mount PSC Motor 4 = R- 40A D Downflow PSC Motor E MulJ- PosiJon Variable- Speed Motor Electrical R MulJ- PosiJon PSC Motor 208/240 V, Phase, 60 Hz S MulJ- PosiJon EEM Motor W Wall Mount PSC Motor Cabinet Width B 7½" Cabinet Finish C 2" U Unpainted D 24½" P Painted N Uncased Nominal Capacity 3 SEER 8 ½ Tons 42 3½ Tons Expansion Device 24 2 Tons 48 4 Tons F Flowrater 36 3 Tons 60 5 Tons T Expansion Valve 2 SS-G

3 Specifications 8B4* 24B4* 30B4* 36C4* 36D4* 42D4* 48D4* 60D4* Nominal Ratings Cooling (BTU/h) 8,000 24,000 30,000 36,000 36,000 42,000 48, Blower Diameter 9½" 9½" 9½" 0⅝" 0⅝" 0⅝" 5 / 6 " 5 / 6 " Width 6" 6" 6" 8" 0⅝" 0⅝" 0⅝" 0⅝" Coil Drain Connect FPT 3/4" 3/4" 3/4" 3/4" 3/4" 3/4" 3/4" 3/4" Refrigerant Line Connection Size Liquid 3/8" 3/8" 3/8" 3/8" 3/8" 3/8" 3/8" 3/8" Suction 3/4" 3/4" 3/4" 7/8" 7/8" 7/8" 7/8" 7/8" Electrical Data Voltage 208/ / / / / / / /230 Min Circuit Ampacity 3/3 3/3 3/3 4/4 4/4 5/5 5/5 6/6 Max. Overcurrent Device (amps) 5/5 5/5 5/5 5/5 5/5 5/5 5/5 5/5 Min. / Max VAC 97/ / / /253 97/ / / / 253 Blower Motor A/ HP.9/ ⅓.9/ ⅓.9/ ⅓ 3./ ⅓ 3.0/ ½ 3.5/ ½ 3.5/ ½ 4.6/ ¾ Ship Weight (lbs) SS-G 3

4 Dimensions.63" (4.3 cm).45" (3.68 cm) 3.08" (7.82 cm) 2" 4.50" (.43 cm) 2.9" (7.39 cm) 2.93" (7.44 cm) 7.5" (9. cm) 5.2" (3.3 cm) 9.2" DRAIN PORT DETAIL.55" (.40 cm) C B.55" (.40 cm) 3." (7.9 cm).4" (3.6 cm).3" (28.70 cm).55" (.40 cm) PLASTIC EAKER COVER.8" (4.6 cm) LOGO LOCATION 2.7" (5.5cm) SUCTION TUBE LIQUID LINE A G INLET TUBE SEE DRAIN PORT DETAIL H E D.73" (4.39 cm) F INLET (FRONT VIEW).73" (4.39 cm) " (2.54 cm) 9.5" (49.5 cm) INLET (RIGHT SIDE VIEW).55" (.40 cm) Model A B C D E F G H 8B4* B4* B4* C4* D4* D4* D4* D4* SS-G

5 Airlfow Data Model 8B4 24B4 30B4 36C4 36D4 42D4 48D4 60D4 Blower Speed Static Pressure (in w.c) Airflow (CFM) High,85,25,065, Medium Low High,85,25,065, Medium Low High,45,085, Medium Low High,580,55,445,395,345,240,55 Medium,385,350,300,250,70,095,005 Low,260,205,75,05, High,85,770,705,640,555,450,355 Medium,580,525,485,420,350,275,65 Low,220,80,40,085, High,990,95,80,765,690,585,435 Medium,655,605,555,480,295,200,060 Low,480,420,350,290,85,00,045 High,960,905,845,780,75,645,570 Medium,600,545,495,435,360,290,25 Low,395,340,280,220,50,090,020 High 2,205 2,40 2,080 2,00,945,870,795 Medium,985,935,865,85,755,695,635 Low,600,555,505,455,405,345,295 Notes. Airflow data indicated is at 230V without air filter in place. 2. The chart is for information only. For satisfactory operation, external static pressure must not exceed value shown on rating plate. The shaded area indicates ranges in excess of maximum recommended design external static pressure. 3. Use the CFM adjustment factors of 0.98 for horizontal left and 0.96 for horizontal right & downflow orientations SS-G 5

6 Heat Kit Applications Model 8B4-A* 24B4-A* 30B4-A* 36C4-A* 36D4-A* 42D4-A* 48D4-A* 60D4-A* HKSX03XC* X X X X X X X X HKSX05XC* X X X X X X X X HKSX06XC* X X X X X X X X HKSX08XC* X X X X X X X X HKSX0XC* X X X X X X X X HKSC05XC* X X X X X X X X HKSC08XC* X X X X X X X X HKSC0XC* X X X X X X X X HKSC5XA* X X X X X X HKSC5XB* X X X X X X HKSC9CA* X HKSC9CB* X HKSC20DA* X X X X HKSC20DB* X X X X * Revision level that may or may not be designated Note: Refer to the minimum airflow requirements for each of the heat kits Single-Point Kit ** Model HKSC5X* HKSC9** HKSC20** SPW-0 X X X ** Must be installed along with any of the above compatible heat kits. This kit will fit any air handler as long as a compatible heat kit is installed in the unit. 6 SS-G

7 Wiring Diagram HTR TL M R M HTR2 TL HTR TL M M3 R M2 M HTR TL HTR2 TL HTR3 TL YL YL M M3 M M2 M4 M2 R R2 YL HTR TL HTR2 TL HTR3 TL YL HTR4 TL 2 3 M M3 M5 M7 YL 4 M2 M4 M6 M8 R R YL 8 9 L L2 L L2 L L2 L L2 ONE () ELEMENT ROWS TWO (2) ELEMENT ROWS THREE (3) ELEMENT ROWS FOUR (4) ELEMENT ROWS L L2 L L2 NOTE: EN INSTALLING HEATER KIT, ENSURE SPEED TAP IS NOT BELOW MINIMUM OWER SPEED (MBS) SPECIFIED FOR THE AIR HANDLER/HEATER KIT COMBINATION ON THIS UNITS SERIAL PLATE. AFTER INSTALLING OPTIONAL HEAT KIT, MARK A "X" IN THE PROVIDED ABOVE. MARK ACCOING TO THE NUMBER OF HEATER ELEMENT ROWS INSTALLED. NO MARK INDICATES NO HEAT KIT INSTALLED. 5 ELEMENT ROWS DATA SUPPLIED WITH HEATER KIT. SEE NOTE 2 TERMINAL OCK SHOWN FOR 50HZ MODELS ONLY L L2 EQUIPMENT GROUND USE COPPER WIRE 208/240 VOLTS GR SR 2 3 G L L2 2 PLM PLM 3 PLM 2 SEE NOTE 4 RC EM HI LO M M2 NC NO EBTDR COM 2 3 SEE NOTE TR GR SPEEDUP COPPER POWER SUPPLY (SEE RATING PLATE) USE MIN. 75 C FIELD WIRE G EBTDR R K XFMR-R XFMR-C K C M IF REPLACEMENT OF THE ORIGINAL WIRES SUPPLIED WITH THIS ASSEMY IS NECESSARY USE WIRE THAT CONFORMS TO THE NATIONAL ELECTRIC CODE. SEE NOTE 5 NO COM NC M2 SEE NOTE 3 THREE SPEED MOTOR WIRING (SELECT MODELS ONLY) SEE NOTE 3 (M2) (M) (TR ) RC (COM) LOW MEDIUM HIGH C V 4 EM 3 SPEED SEE NOTE 240 TR RC EM EBTDR R 4 24V EBTDR GR COLOR CODE WIRING CODE ACK GR GREEN FACTORY WIRING YL RED YELLOW RPLE OWN HIGH VOLTAGE LOW VOLTAGE UE ITE FIELD WIRING HIGH VOLTAGE COMPONENT CODE LOW VOLTAGE EM RC EVAPORATOR MOTOR RUN CAPACITOR TR TRANSFORMER FEMALE PLUG CONNECTOR SR STRAIN RELIEF PLM MALE PLUG CONNECTOR R RELAY FUSE LINK EBTDR ELECTRONIC OWER TIME TL THERMAL LIMIT NOTES: DELAY RELAY HTR HEAT ELEMENTS ) RED WIRES TO BE ON TRANSFORMER TERMINAL "3" FOR 240 VOLTS AND ON TERMINAL "2" FOR 208 VOLTS. 2) SEE COMPOSITE WIRING DIAGRAMS IN INSTALLATION INSTRUCTIONS FOR PROPER LOW VOLTAGE WIRING CONNECTIONS. 3) CONFIRM SPEED TAP SELECTED IS APPROPRIATE FOR APPLICATION. IF SPEED TAP NEEDS TO BE CHANGED, CONNECT APPROPRIATE MOTOR WIRE (RED FOR LOW, UE FOR MEDIUM,AND ACK FOR HIGH SPEED) ON "COM" CONNECTION OF THE EBTDR. INACTIVE MOTOR WIRES SHOULD BE CONNECTED TO "M OR M2" ON EBTDR. 4) OWN AND ITE WIRES ARE USED WITH HEAT KITS ONLY. 5) EBTDR HAS A 7 SECOND ON DELAY EN "G" IS ENERGIZED AND A 65 SECOND OFF DELAY EN "G" IS DE-ENERGIZED. 040A00058-B C G Wiring is subject to change. Always refer to the wiring diagram or the unit for the most up-to-date wiring. Warning High Voltage: Disconnect all power before servicing or installing this unit. Multiple power sources may be present. Failure to do so may cause property damage, personal injury, or death. SS-G 7

8 Accessories Downflow Insulation Kit DPI-B DPI-C DPI-D 8B4** 36C4** 36D4** 24B4** 30B4** 42D4** 48D4** 60D4** Goodman Manufacturing Company, L.P., reserves the right to discontinue, or change at any time, specifications or designs without notice or without incurring obligations. 202 Goodman Manufacturing Company, L.P. Houston, Texas Printed in the USA. 8 SS-G