ALLWEILER. Pressure relief valves, directly controlled. Series DS/DT
|
|
- Britton Collins
- 5 years ago
- Views:
Transcription
1 ALLWEILER Pressure relief valves, directly controlled Range of application The pressure relief valves of can be applied for maximum operating temperatures up to 150 C (higher temperatures on request). The pressure relief valves can be applied for mineral and synthetic hydraulic oils, lube oils and fuel oils. They are not to be used for corrosive, abrasive and contaminated fluids. The branch current thus generated flows through space (B) or space (T) into the pump suction chamber or through the balance pipeline into the pressureless tank. The operating pressure decreasing to below the set opening pressure, the valve cone (8) closes the valve seat (i), and no further fluid pumped flows from space (A) to space (B) and/or (T). The operating pressure is built up again in space (A). The exact operating data of the pressure relief valve such as pressures, maximum rate of flow and viscosity range can be taken from the data sheet. Structural Design The valve casing (1) has a delivery side connection (A) and suction side connection (B) or connection (T) to the tank. Switching diagram according to DIN/ISO 1219 The valve cone (8) is guided in the valve casing (1) and pressed onto the valve seat (i), metallically sealing, by means of the valve spring (29). The O ring (20) in the valve spring plate closes the pressure relief valve sealing to the outside. The opening pressure is adjusted by means of the adjusting screw (17) and the valve spring (29). The adjusting screw (17) is fixed in its position, checked by means of the hexagon nut (31). Mode of operation Through opening (A), the fluid pumped enters the valve casing where it is under a specific operating pressure pressing against the valve cone (8). The valve cone (8) is pressed onto the valve seat by means of the force of the pretensioned valve spring (29), and closes the connection between space (A) and space (B). The system pressure in space (A) overcoming the force of the pre tensioned pressure spring (29), valve cone (8) is lifted off from the valve seat. Operation Operation with adjusting screw By means of the adjusting screw (17), the respective opening pressure is adjusted. Clockwise rotation: Pressure build up Counterclockwise rotation: Pressure reduction 1
2 Abbreviation Pressure relief valve Material design of spring S = screw spring T = cup spring Max. opening pressure Valve size Flow max. l/min Pressure max. bar : A = built on, back to suction B = built on, back to suction with hand regulation C = built on, return to tank D = built on, return to tank with hand regulation E = Pipeline corner valve F = Pipeline corner valve with hand regulation * max. flow with pipeline valves Characteristics of construction Cone seat valve Flow range [l/min] 10 to 3600 Fluids Lube, hydraulic, fuel oils, oil in water emulsions Temperature range [ C] 20 to +150 (250 C on request) Viscosity range [mm 2 /s] 10 to Standard materials: Casing: GG / GGG / GS / ST Valve cone: GG / ST / MS O rings: NBR / Viton 2
3 s A B C D E F 3
4 Sectional drawing with parts list Pressure relief valve, Series DS.. ( A = built on, back to suction) Design with hand regulation Denomination Part No. Valve casing 1 Cover 5 Valve spring plate 7 Valve cone 8 Adjusting screw 17 O ring 20 Joint ring 26 Valve spring 29 Hexagon nut 31 Socket head cap screw 32 Screw plug 37 Socket head cap screw 44 O ring 48 Denomination Part No. Spindle nut 50 Guide bush 51 Valve spindle 52 O ring 53 Key 54 Circlip 56 Replacement parts/spare parts 4
5 Valve dimensions and connections E/F E F Size Material Inlet Outlet Dimensions 5
6 Valve dimensions and connections E/F Casing material GG/GGG/GS E F Design with DS/DT44 Size Inlet Flange Outlet Flange Dimensions 6
7 Valve dimensions and connections E/F Casing material welded steel E F Size Inlet Flange Outlet Flange Dimensions 7
8 Subject to technical alterations. A Member of the COLFAX PUMP GROUP ALLWEILER AG Werk Radolfzell Postfach Radolfzell Allweilerstraße Radolfzell Germany Tel. +49 (0) Fax +49 (0) service@allweiler.de Internet: 8
ALLWEILER. Pressure relief valves, indirectly pilot controlled. Series DVI
Pressure relief valves, indirectly pilot controlled Series DVI Range of application The pressure relief valves of Series DVI can be applied for maximum operating temperatures up to 150 C (higher temperatures
More informationALLWEILER. Pressure-relief valves, indirectly pilot-controlled. Series DVI
Pressure-relief valves, indirectly pilot-controlled Series DVI Range of application The pressure-relief valves of Series DVI can be applied for maximum operating temperatures up to 150 C (higher temperatures
More informationScrew Pumps Series EMTEC HIGH-TECH FOR EMULSION. 20 DQ axial branch with pipe thread. 140 D8.6 radial branch with SAE flange
Screw Pumps 20 DQ axial branch with pipe thread HIGH-TECH FOR EMULSION 140 D8.6 radial branch with SAE flange Application For handling good, medium or mal-lubricating, abrasive fluids in cooling lubricant
More informationSupply plus delivery pressure must not exceed the admissible internal pump pressure.
Vertical High-Pressure Centrifugal Pump Series CVP Application For handling pure water and condensates. The fluids to be pumped must not contain any abrasive particles nor chemically attack the pump materials.
More informationScrew Pumps Series SPF
Screw umps Application For the delivery of fuel oils, lube oils, hydraulic oils or other lubricating liquids. The fluid media must not contain any abrasive particles nor attack the pump materials chemically.
More informationScrew Pump Twin Aggregates Series SPZ/M MagDrive
Screw Pump Twin Aggregates Series SPZ/M MagDrive Application For the delivery of fuel oils, hydraulic oils or other lubricating liquids. The fluid media must not contain any abrasive particles nor attack
More informationVolute Casing Centrifugal Pumps in In-line Design with Magnetic Drive. Series CNI-M
Volute Casing Centrifugal Pumps in In-line Design with Magnetic Drive Series CNI-M Usage For pumping toxic, volatile, explosive or other fluids harmful to the environment which call for service of hermetically
More informationVolute Casing Centrifugal Pumps in High Temperature Design with Magnetic Drive. Series CNH-ML
Volute Casing Centrifugal Pumps in High Temperature Design with Magnetic Drive Series CNH-ML Usage For pumping toxic, volatile, explosive or other fluids harmful to the environment which call for service
More informationVolute Casing Centrifugal Pumps according to EN 22858, ISO 2858 with Magnetic Drive. Series CNH-M
Volute Casing Centrifugal Pumps according to EN 22858, ISO 2858 with Magnetic Drive Series CNH-M Usage For pumping toxic, volatile, explosive or other fluids harmful to the environment which call for service
More informationNorm-Centrifugal Pumps PN 10
Norm-Centrifugal Pumps PN 10 Pump dimensions acc. to DIN EN 733 with additional sizes Technical requirements acc. to DIN ISO 9908 Application For pumping pure water, industrial water, sea water, condensate,
More informationVolute Casing Centrifugal Pumps PN 16 for Heat Transfer Oils up to 350 C Series NTT Pump dimensions acc. to DIN EN 733 with additional sizes
Volute Casing Centrifugal Pumps PN 16 for Heat Transfer Oils up to 350 C Series NTT Pump dimensions acc. to DIN EN 733 with additional sizes Application For handling organic heat-transfer oils in heat
More informationPropeller Pump. Performance data Delivery flow Q up to m³/h Delivery head H up to 1,5 m Liquid temperature t up to 100 C Delivery branch
Propeller Pump Utilization and main fields of application For pumping sewage containing nitrate or activated sludge from the nitrification basin to the denitrification basin (recirculation). Further for
More informationPN 16 Volute Centrifugal Pumps (depending on materials up to PN 25) according to EN 22858/ISO 2858 and EN ISO 5199
PN 16 Volute Centrifugal Pumps (depending on materials up to PN 25) according to EN 22858/ISO 2858 and EN ISO 5199 Utilization Used to pump non-aggressive or aggressive liquids, cold or hot liquids, clean
More informationVolute Casing Centrifugal Pumps of Inline Design Series NI
Volute Casing Centrifugal Pumps of Inline Design Series NI Application For pumping pure water, industrial water, sea water, condensates, oils, brines, lyes and hot water. The fluids to be pumped must not
More informationALLWEILER. Block Macerators Series ABM Designs S and I. Design I with controller and seal water unit
Block Macerators Series ABM Designs S and I Design S Design I with controller and seal water unit Usage Macerators chop solids conveyed in liquids; materials like wood, textiles, plastics, paper, rubber,
More informationHigh-Pressure Centrifugal Pumps
High-Pressure Centrifugal Pumps L LV Application For handling fluids which do not contain any abrasive particles nor chemically attack the pump materials. Main fields of application In water supply, booster,
More informationScrew Pumps Series EMTEC. with ALLSPEED Controller HIGH-TECH FOR EMULSION. 20 DQ axial suction branch with pipe thread
Screw Pumps DQ axial suction branch with pipe thread with ALLSPEED Controller HIGH-TECH FOR EMULSION 1 D8.6 radial suction branch with SAE flange Applications For handling liquids with good, limited or
More informationTilting-disc Check Valves Short Body
Tilting-disc Check Valves Short Body Tilting-disc Check Valves, Short Body to DIN 3202 Series F4 for liquids and gases, PN 10 - PN 40, DN 150 - DN 2000 Short Body Tilting-disc Check Valves More than 40
More informationLPE3. Std Line. Product Description. Max differential pressure: 16 bar Circulation, lubrication and transfer LPE GB
LPE3 Std Line Product Description Flow volume: 10-180 l/min Max differential pressure: 16 bar Applications: Circulation, lubrication and transfer 1. Applications 1.1 Functionality The Std Line (standard)
More information8L SERIES THREE SCREW PUMPS
TM 8L SERIES THREE SCREW PUMPS The reliable pump people ROTARY SCREW PUMPS Performance Shown at 1500 PSID (103 BAR), 200 SSU (43 CST) 60 HZ: 870 1150 1750 50 HZ: 960 1450 1200 1100 630M 40 250 1000 900
More informationACF5. Std Line. Product Description. Max differential pressure: 16 bar Circulation, lubrication and transfer ACF GB
ACF5 Std Line Product Description Flow volume: 310-2900 l/min Max differential pressure: 16 bar Applications: Circulation, lubrication and transfer 1. Applications 1.1 Functionality The ACF pumps are used
More informationProgressive Cavity Pumps in Block Design TECFLOW Series
Progressive Cavity Pumps in Block Design TECFLOW Series Applications In waste water and waste water treatment engineering and in environmental industries for pumping low and high viscous liquids, neutral,
More informationPeristaltic pumps SERIES ASH
Peristaltic pumps SERIES ASH Design ID Applications In wastewater and clarification plants; the chemical and petrochemical industry; pulp, paper, and textile industry; soap and grease industry; construction;
More informationLPE4. OptiLine. Product Description. Max differential pressure: 16 bar LPE GB
LPE4 OptiLine Product Description Flow volume: 8-175 l/min Max differential pressure: 16 bar Applications: Circulation and transfer 1. Applications 1.1 Functionality The LPE OptiLine pump is used for a
More informationTRITEC SERIES THREE SCREW PUMPS
TM TRITEC SERIES THREE SCREW PUMPS The reliable pump people ROTARY SCREW PUMPS Performance Shown at 3500 RPM, 1.0 Centistokes DIFFERENTIAL PRESSURE, bar 280 0 20 40 60 80 1100 260 1000 440-46 Low Viscosity
More informationFeed Pumps VP / VPB / VPBM
Feed Pumps VP / VPB / VPBM Symbol General The feed pumps from the VP series are low-noise, single-stroke vane pumps with constant flow rate. Using a damped bell housing (PT) enables noise levels to be
More informationTOOLS FOR THE SPECIALIST IMPACT WRENCHES
TOOLS FOR THE SPECIALIST ES MACHINE FEATURES Planetary gear Rotation direction reversible Type for underground mining (6 1035 0010) Push button actuation inlet and exhaust Torque adjustment TECHNICAL SPECIFICATION
More informationVolute Casing Centrifugal Pumps PN 16 for heat-transfer liquids Heat-transfer oil up to 350 C Hot water up to183 C
Volute Casing Centrifugal Pumps PN 16 for heat-transfer liquids Heat-transfer oil up to 350 C Hot water up to183 C Series CMIT in inline design Series CMAT with axial inlet ATEX 0 a Series CMAT Series
More informationACG7. Std Line. Product Description. Max differential pressure: 16 bar Circulation, lubrication and transfer ACG GB
ACG7 Std Line Product Description Flow volume: 80-1200 l/min Max differential pressure: 16 bar Applications: Circulation, lubrication and transfer 1. Applications 1.1 Functionality The Std Line (standard)
More informationEMTEC Series 3-Screw
EMTEC Series 3-Screw Coolant and Emulsion Pumps The reliable pump people Rotary Screw Pumps Performance Shown at 1.8 cst, 3500 RPM Differential Pressure PSI 20-38 20-46 20-56 40-38 40-46 80-36 80-46 140-39
More informationSeries PRODUCTS. self-priming Horizontal screw pump for non lubricating liquids. Water. Seawater. Heavy fuel oils. Bilge/Ballast pumps
self-priming Horizontal screw pump for non lubricating liquids PRODUCTS Water Seawater Oils Heavy fuel oils Light products Labelling Bilge/Ballast pumps General service pumps Cargo pumps Transfer pumps
More informationChange-Over Pressure Filter DFDK
Change-Over Pressure Filter up to 2500 l/min, up to 315 bar 30 60 110 140 160 240 280 330 500 660 1.x 660 2.x 990 2.x 1320 2.x 1320 3.x 2640 3.x 3960 3.x 1. TECHNiCAL SPECIFICATIONS 1.1 FILTER HOUSING
More informationwith ALLSPEED Controller Screw Pumps HIGH-TECH FOR EMULSION 20 DQ axial suction branch with pipe thread 140 D8.6 radial suction branch with SAE flange
with ALLSPEED Controller Screw Pumps 20 DQ axial suction branch with pipe thread HIGH-TECH FOR EMULSION 140 D8.6 radial suction branch with SAE flange Applications For handling liquids with good, limited
More informationPN 16/PN 25 Volute Centrifugal-Pumps for Heat Transfer Media Thermal Oil up to 400 C Hot Water up to 207 C
PN 16/PN 25 Volute Centrifugal-s for Heat Transfer Media Thermal Oil up to 00 C Hot Water up to 7 C Series NTWH/CTWH Series NBWH/CBWH Series NIWH/CIWH Application For circulating heat transfer media such
More informationACF5. Std Line. Product Description. Max differential pressure: 16 bar Circulation, lubrication and transfer
ACF5 Std Line Product Description Flow volume: 310-2900 l/min Max differential pressure: 16 bar Applications: Circulation, lubrication and transfer ALSO VALID FOR PUMP SERIES UCF Generation 5 1. Applications
More informationIPVP High-pressure Internal Gear Pumps for Variable Speed Drives
IPVP High-pressure Internal Gear Pumps for Variable Speed Drives Design and Function 7 6 5 9 2 5 6 7 8 2 9 4a 4b 3 Pinion shaft 2 Internal gear 3 Filler pin 4a Filler segment carrier 4b Filler sealing
More informationIPVP High-pressure Internal Gear Pumps for Variable Speed Drives Technical Data Sheet
IPVP High-pressure Internal Gear Pumps for Variable Speed Drives Technical Data Sheet Design and Function 7 6 5 9 2 8 2 9 4a 4b 3 Pinion shaft 2 Internal gear 3 Filler pin 4a Filler segment carrier 4b
More informationEMTEC -C PUMPS FOR HIGH PRESSURE COOLANT SUPPLY
CAPABILITIES EMTEC -C PUMPS FOR HIGH PRESSURE COOLANT SUPPLY BRINGING NEXT LEVEL PERFORMANCE TO COOLANT PUMPS ALLWEILER 2 3 PUMP LIFE INTO YOUR MOST CRITICAL EQUIPMENT COOLANT PUMPS CAN SIGNIFICANTLY EXTEND
More informationACD6. Std Line. Product Description. Max differential pressure: 7 bar Circulation, lubrication and transfer ACD GB
ACD6 Std Line Product Description Flow volume: 10-42 l/min Max differential pressure: 7 bar Applications: Circulation, lubrication and transfer 1. Applications 1.1 Functionality The ACD pumps come in two
More informationPVD /117 ED VARIABLE DISPLACEMENT VANE PUMPS WITH DIRECT PRESSURE ADJUSTER OPERATING PRINCIPLE
14 100/117 ED PVD VARIABLE DISPLACEMENT VANE PUMPS WITH DIRECT PRESSURE ADJUSTER OPERATING PRINCIPLE The PVD pumps are variable displacement vane pumps with mechanical pressure compensator. The pressure
More informationRV1P /118 ED VARIABLE DISPLACEMENT VANE PUMPS SERIES 10 OPERATING PRINCIPLE TECHNICAL SPECIFICATIONS HYDRAULIC SYMBOL
14 201/118 ED RV1P VARIABLE DISPLACEMENT VANE PUMPS OPERATING PRINCIPLE TECHNICAL SPECIFICATIONS (measured with mineral oil with viscosity of 46 cst at 40 C) RV1P are variable displacement vane pumps with
More informationSide channel pump PN 40 SRZ. self-priming, according to DIN EN 734. Technical description
Side channel pump PN 0 self-priming, according to DIN EN 7 SRZ Technical description SRZ pumps are self-priming side channel pumps in multistage construction capable of handling aerated liquids. They have
More informationAP212HP Cast Iron Gear Pumps
Cast Iron Gear Pumps Standard and Low Noise series Reference: 200-P-991236-EN-01 Issue: 09.2016 1/56 Contents Page 1 General information... 5 1.1 External gear pumps components... 6 1.2 Technical data...
More informationVPN1-06. Functional Description HA /2008. Pilot Operated Pressure Relief Valves. Replaces HA /2002
Pilot Operated Pressure Relief Valves VPN-06 HA 56 4/2008 Size 06 p max up to 320 bar Q max up to 70 L/min Replaces HA 56 3/2002 Cartridge, modular and in-line design Five pressure ranges Two pressure
More informationTPV Variable Displacement Closed Loop System Axial Piston Pump THE PRODUCTION LINE OF HANSA-TMP HT 16 / M / 852 / 0815 / E
HYDRAULIC COMPONENTS HYDROSTATIC TRANSMISSIONS GEARBOXES - ACCESSORIES Certified Company ISO 9001-14001 ISO 9001 Via M. L. King, 6-41122 MODENA (ITALY) Tel: +39 059 415 711 Fax: +39 059 415 729 / 059 415
More information4.2 FIXED DISPLACEMENT DOUBLE PUMP
4.2 FIXED DISPLACEMENT DOUBLE PUMP CONTENTS PVF101 Ordering Code 4.2.1 Fixed Displacement Technical Information 4.2.2 Specifications 4.2.3 Hydraulic fluids 4.2.4 Viscosity range 4.2.5 Temperature range
More informationTechnical Data and Operating Instructions Thermal Dry Running Protection ATLS-T1
Technical Data and Operating Instructions Thermal Dry Running Protection ATLS-T1 Operational data for thermal dry running protection according to order data sheet Order No.: Ident No. ATLS-T1: Machine
More informationGRUNDFOS DATA BOOKLET MTS. Screw pumps 50/60 Hz
GRUNDFOS DATA BOOKLET MTS Screw pumps / Hz Contents Introduction MTS 3 Performance range - MTS, Hz 4 Performance range - MTS, Hz 5 Performance range - MTS, Hz 5 General description Main applications 6
More informationDischarge rate* 2 L/min MPa (DE10-1) 37.8 MPa (DE10-7)
D VANE PUMPS D VANE PUMPS Operating pressure MPa {kgf/cm } Maximum Rated Discharge rate* L/min Permissible min Page DS DSP 7 {7} 7 {7} to D- MD Motor pumps incorporating a DSP D-4 DP DP DP DP 7. {7} 4
More informationPump your business. 40 bar program. Screw pumps series SMxT16B Dry & submersible screw pumps for industrial applications
Pump your business 40 bar program Screw pumps series SMxT16B Dry & submersible screw pumps for industrial applications The people behind the Settima pumps The Settima Meccanica adventure started in early
More informationFlow volume: 2-24 l/min Max differential pressure: 10 bar Applications: Lubrication, circulation and transfer
Screw pump Series LPD Product description Flow volume: 2-24 l/min Max differential pressure: 10 bar Applications: Lubrication, circulation and transfer The LPD pump is used for a number of different fluids:
More informationIPVS High-pressure Internal Gear Pumps Technical Data Sheet
IPVS High-pressure Internal Gear Pumps Technical Data Sheet Functional Drawing 5 9 2 8 2 9 4a 4b 3 Pinion shaft 2 Internal gear 3 Filler pin 4a Filler segment carrier 4b Filler sealing segment 5 Axial
More informationSuction Filter SF/SFM/SFF and Suction Filter Elements S/S..
Suction Filter /M/F and Suction Filter Elements S/S.. up to 500 l/min Filters: 60 110 160 240 330 M 330 F 400 F 500 Elements: S SH. SU. SG. 1. TECHNICAL SPECIFICATIONS 1.1 FILTER HOUSING Construction The
More informationInline Filter LPF D A Flange-Mounted up to 280 l/min, up to 25 bar
Inline Filter LPF D A Flange-Mounted up to 280 l/min, up to 25 bar 160 240 260 280 1. TECHNiCAL SPECIFICATIONS 1.1 FILTER HOUSING Construction The filter housings are designed in accordance with international
More informationMS-Series. S Series. Twin Triple Screw Pumps.
MS-Series S Series Twin Triple Screw Pumps W h e r e I n n o v a t i o n F l o w s www.maag.com Triple Screw Pump S E R I E S A Safer, Greener, More Cost-Effective Pumping Solution Maag, part of Dover
More informationTransfer Gear Pumps KF 3/100...KF 6/630
Transfer Gear Pumps KF 3/00...KF 6/630 Applications, Suitable Fluids Applications Centrifuge construction, Coating machines, Compressors Engine construction Filling stations, Filter systems Generator construction
More informationAIR OPERATED OIL PUMPS AND KITS
PM 2 AIR OPERATED OIL PUMPS AND KITS PM 2 Oil pump, pressure ratio : 0 Double acting air operated pumps for transferring lubricants and other non-corrosive fluids. Pump includes bung adapter. New Model
More informationTransfer Gear Pumps KF 3/100...KF 6/730
Transfer Gear Pumps KF 3/00...KF 6/730 Transfer Gear Pumps KF 3/00... KF 6/730 Contents Technical Data Page Applications / Suitable fluids.............................................. 3 Construction...........................................................
More informationAXIAL PISTON PUMPS SHPV SECTIONAL VIEW
AXIAL PISTON PUMPS SHPV SECTIONAL VIEW 2 SYSTEM CIRCUIT PUMP AND MOTOR CIRCUIT working loop (high pressure) working loop (low pressure) control fluid suction line case drain fluid Above figure shows schematically
More informationKAM E-IAS ELECTRIC ISOKINETIC AUTOMATIC SAMPLER
KAM E-IAS ELECTRIC ISOKINETIC AUTOMATIC SAMPLER PER API 8.2, ASTM D4177 AND ISO 3171 User Manual EIASMANUAL0718 TEL +1 713 784-0000 FAX +1 713 784-0001 Email Sales@Kam.com 3939 Ann Arbor Drive Houston,
More informationNOTOS Multi Screw Pumps. High Efficiency and Unique Design
NOTOS Multi Screw Pumps High Efficiency and Unique Design NOTOS MULTI SCREW PUMPS 3 ranges for all applications Since 1979 NETZSCH has been manufacturing multi screw pumps to serve a wide range of industries
More informationPressure Filter DF...K P, DF...M P, Flange Mounted
Pressure Filter, DF...M P, Flange Mounted up to 550 l/min, up to 260 bar DF...M P 330...1.X 160 240 280 500...1.X 660...1.X 660...2.X 990...2.X 1320...2.X 660...3.X 990...3.X 1320...3.X 1. TECHNICAL SPECIFICATIONS
More informationAP212 Gear Pumps. Standard and Low Noise series. Reference: 200-P EN-03 1/60. Issue:
Gear Pumps Standard and Low Noise series Reference: 2-P-99123-EN-3 Issue: 9.215 1/6 Contents Page 1 General information... 4 1.1 External gear pumps components... 5 1.2 Example of typical sound pressure
More informationVPN2-10/MR. Functional Description HU /2008. Pilot Operated Pressure Relief Valves. Replaces HU /2005
Pilot Operated Pressure Relief Valves VPN2-10/MR Size 3/8 (10)...5076 PSI (350 bar)...40 GPM (150 L/min) 7/2008 Replaces 2/2005 Modular and in-line design Five pressure ranges Two pressure adjustment options:
More informationGear Pump KF 0. KF 0 A pump for process engineering. General characteristics. Operation characteristics. Materials
Gear Pumps KF 0 Gear Pump KF 0 KF 0 A pump for process engineering The central element in numerous technical processes is the metering of liquids. PUR components, plasticisers, resins, adhesives, laquers
More informationReturn Line Filter RFM with 4-Hole Mounting
Return Line Filter with 4-Hole Mounting Tank-top mounted versions: up to 850 l/min, up to 10 bar 75 90 150 165 185 195 210 270 330 500 600 661 851 1. TECHNICAL SPECIFICATIONS 1.1 FILTER HOUSING Construction
More informationReturn Line Filter RFM with 4-Hole Mounting
Return Line Filter with 4-Hole Mounting Tank-top mounted versions: up to 850 l/min, up to 10 bar 75 90 150 165 185 210 270 330 500 600 661 851 1. TECHNiCAL SPECIFICATIONS 1.1 FILTER HOUSING Construction
More informationAIR OPERATED OIL PUMPS AND KITS
PM 2 PumpMaster 2 Oil pump, pressure ratio : 0 Double acting air operated pumps for transferring lubricants and other non-corrosive fluids. Pump includes bung adapter. Model 24 PumpMaster 2, : ratio stub
More informationBlock mounting filter, lateral flange-mounting possible
Block mounting filter, lateral flange-mounting possible RE 0/.0 Replaces: 0.09 / Types 0/0 FEN 000 to 000; 0/0 FE 000, 00, 008 Nominal sizes according to DIN 0: 000 to 000 Nominal sizes according to BRFS:
More informationPRODUCT CATALOG COMMERCIAL MARINE
PRODUCT CATALOG COMMERCIAL MARINE CRUISE VESSELS CONTAINER VESSELS BULK CARRIER VESSELS OIL TANKERS OFFSHORE SUPPLY VESSELS PLATFORMS/RIGS SPECIALIZED VESSELS REDEFINING WHAT S POSSIBLE Whether on the
More informationFunctional Description
4/2 Way Solenoid Operated Directional Control Valves Spool SD2E-A4 Type 3/4-16 UNF p max 350 bar (5076 PSI) Q max 30 L/min (7.9 GPM) 01/2005 4/2 Way cartridge valves solenoid operated spool directed Manual
More informationIPC Medium-Pressure Internal Gear Pumps Technical Data Sheet
IPC Medium-Pressure Internal Gear Pumps Technical Data Sheet Function 5 9 2 8 2 9 4a 4b 3 Pinion shaft 2 Internal gear 3 Filler pin 4a Filler segment carrier 4b Filler sealing segment 5 Axial disc Axial
More information1.3 HIGH PRESSURE SERIES
1.3 HIGH PRESSURE SERIES content Ordering Code 1.3.1 High Pressure Series Technical Information 1.3.2 Specifications 1.3.3 Hydraulic Fluids 1.3.4 Viscosity Range 1.3.5 Temperature Range 1.3.6 Seals 1.3.7
More informationThermoplastic Centrifugal pump, Type NM
Thermoplastic Centrifugal pump, Type NM acc. to DIN 24256, EN 22858 and ISO 2858 Size: 32-125 up to 150-400 Capacity Q: up to 450 m 3 / h Head H: up to 100 m Operating temperature t: PE up to + 70 C PP
More informationProportional pressure reducing valve, pilot operated
Proportional pressure reducing valve, pilot operated RE 29175/7.5 Replaces: 11.2 1/1 Types DRE and ZDRE Size 6 Component series 1X Maximum operating pressure 21 bar Maximum flow l/min H446 Table of contents
More informationAutomatic metal-edge filters AF 72 G
Automatic metal-edge filters AF 72 G with radial scraper cleaning Connection size G1 1/2, flange DN 40 1 Short description MAHLE automatic metal-edge filters are suitable for all applications where low
More informationTransfer Gear Pumps KF
Transfer Gear Pumps KF 4...80 2 KRACHT GmbH Gewerbestr. 20 58791 Werdohl, Germany fon +49(0)23 92/935-0 fax +49(0)23 92/935 209 web www.kracht.eu mail info@kracht.eu Contents Technical Data Page Applications
More informationElectric Immersion Pumps PXA and PXK, sealless
1-6062-US PXA and PXK, sealless MQUALITY MANAE ENT Cooling and lubricating with high-pressure... Centrifugal pumps for delivery pressures up to 25 bars Technical data Delivery rate Q max = 185 l/min Delivery
More informationHYDRAULIC-MOTORS. Radial Piston Motors with fixed displacement RM...X series V g = 250 cm 3 /rev cm 3 /rev
s with fixed displacement RM...X series V g = 250 cm 3 /rev - 900 cm 3 /rev HYDRAULIC-MOTORS Catalogue No. HM1-015E RM 250X - RM 900X Page 2 Features: many displacements for all applications very high
More informationInline Filters NF. Flow rates up to 3,500 l/min Pressure range 25 bar Material: Aluminium / Aluminium-Cast Iron
NF filters are designed for inline mounting and as tank-top mounted return line filters. These filters can also be used on filling, flushing and off-line units. Inline Filters NF Flow rates up to 3,500
More informationKRAL Screw Pumps. L Series. Catalog. L Series Edition 05/2011 Subject to change.
KRAL Screw Pumps. L Series. Catalog L Series Edition 05/2011 Subject to change. 2 L Series Edition 05/2011 Catalog Table of contents Description Type code 5 Structure 6 Direction of rotation and flow direction
More informationNORI 320 Globe valves PN DN Application Standard variants Operating data Materials Remarks Design
Type series booklet 7653.1/8-10 NORI 320 Globe valves with gland packing with non-turning stem flanged or butt-weld ends ZXLF ZXSF PN 250-320 DN 65-200 Application In industrial plants, power stations,
More informationPS/PSL Centrifugal pumps
1 14 EN Centrifugal pumps Technical Data Delivery rate Q max = 1250 l/min Delivery head H max = 110 m Delivery temperature T = 0 C to + C Kinematic viscosity ν max = 30 mm 2 /s Quality Management DIN EN
More informationSpare Parts MH Koltek Valve SP70735-GB
Spare Parts MH Koltek Valve SP70735-GB5 2000-05 Koltek Valve type MH, MHI and MHE Bearing and lid for bearing 2 Double shutter Reg.: 2000-05 Intro.: 9605 Koltek Valve type MH, MHI and MHE Type MH 25 mm
More informationBR 30a. Pneumatic Multi-turn Actuator. Application: Special designs:
Pneumatic Multi-turn Actuator BR 30a Application: Single-acting pneumatic diaphragm multi-turn actuator for butterfl y valves and other rotary valves: The pneumatic BR 30a Multi-turn Actuators are diaphragm
More informationSeries TSW Sheet No J. SUCTION FILTER, horizontal tank mounted. Dimensions: mounting surface
SUCTION FILTER, horizontal tank mounted Sheet No. 1905 J Series TSW 210-310 Dimensions: type TSW 210 TSW 310 connection - 20 SAE -20 SAE A 12.09 15.47 B 11.57 14.96 C 11.42 14.76 D 8.62 12.00 E.26.30 weight
More informationMultiRheo Filter MRF 1/2/3/4/5/6/7
MultiRheo Filter MRF 1/2/3/4/5/6/7 Description The MultiRheo filters of the MRF series are filter housings for use in open systems which are continually exposed to contamination. The candle filter elements
More informationPUMP SIZE Flow rate at 1500 rpm lt/min Operating pressures bar
/7 ED VPPL VARIABLE DISPLACEMENT AXIAL-PISTON PUMPS FOR INTERMEDIATE PRESSURE SERIES OPERATING PRINCIPLE The VPPL are variable displacement axial-piston pumps with variable swash plate, suitable for applications
More informationScrewpump Series ACD
Screwpump Series ACD Product description Flow volume: 11-45 l/min Max differential pressure: 7 bar Applications: Lubrication, circulation and transfer ACD 1116 GB IMO AB, Telephone: + 46 8 50 622 800,
More informationPressure Filter DF Pressure Filter for Reversible Oil Flow DFF/DFFX
Pressure Filter DF Pressure Filter for Reversible Oil Flow DFF/DFFX up to 2000 l/min, up to 420 bar DF/DFF...1.X/2.X 30 60 110 140 160 240 280 330 500 660 990 1320 1500 2000 3000 4000 DF...3.X DFFX...1.X/2.X
More informationChange-Over Inline Filter RFLD Welded Version
Change-Over Inline Filter RFLD Welded Version up to 15000 l/min, up to 16 bar RFLD 1300 CAS to RFLD 15000 CBW 1. TECHNICAL SPECIFICATIONS 1.1 FILTER HOUSING Construction The filter housings are designed
More informationGAS PRESSURE REGULATOR RMG RMG 512b DN 25 to DN 100. RMG 512c DN 150 and DN 250 SERVING THE GAS INDUSTRY WORLDWIDE
SERVING THE GAS INDUSTRY WORLDWIDE OPERATING AND MAINTENANCE INSTRUCTIONS / SPARE PARTS GAS PRESSURE REGULATOR RMG 512 RMG 512b DN 25 to DN 100 512.20 Edition 08/2007 RMG 512c DN 150 and DN 250 RMG REGEL
More informationHYDRAULICS VINCKE HYDRAULIC PUMPS
VINCKE HYDRAULIC PUMPS TECH-VHP200.1 index 3 link to your page / link a su página Gear pumps Introduction 3 Group 0 3 Group 1 3 Group 2 3 Group 3 4 6 7 12 18 Variable displacement pumps 21 Hand pumps 3
More informationAutomatic metal-edge filter AF 75 S / AF 95 S
Automatic metal-edge filter AF 75 S / AF 95 S with radial scraper cleaning housing in welded design, optionally with cyclone effect Connection size DN 150, DN 200, DN 250 others upon request 1. Features
More informationTransfer Gear Pumps KF
Transfer Gear Pumps KF 4...80 Contents Technical Data Page Applications / Suitable fluids..................................................... 4 Construction.................................................................
More informationHigh-pressure inline filter, flangeable
High-pressure inline filter, flangeable RE 51405/08.08 1/1 Types FEN 0040 to 1000; FE 0003, 0015, 0018 Nominal size according to DIN 4550: 0040 to 1000 Nominal size according to BRFS: 0003, 0015, 0018
More informationFeed Pumps Direct Drive Series 1.1.
1.1. FEED PUMP SERIES FZP AND MFZP 1. GENERAL The feed pump, type FZP, is a direct drive vane pump with constant flow rate. It is available with flanged motor (MFZP) and comes with internal pressure relief
More informationVRN2-10. Functional Description HA /2008. Pilot Operated Pressure Reducing Valves. Replaces HA /2003
Pilot Operated Pressure Reducing Valves VRN2-0 HA 554 7/2008 Size 0 p max up to 20 bar Q max up to 50 (80) L/min Replaces HA 554 2/200 Screw-in cartridge valve for manifold mounting and stacking assemblies
More informationOperating instructions FPCC FPFG FPCG FPFX FPAC
Vane pumps Operating instructions FPCC 65 -... FPFG 65 -... Index Page Proper use 2 Type code 2 Technical data 3 Installation 3 Start-up 10 Maintenance 13 Trouble shooting 13 ALFONS HAAR MASCHINENBAU GMBH
More informationVariable Vane Pump, Direct Controlled PV7...A Series 1X / 2X
Variable Vane Pump, Direct Controlled PV7...A Series 1X / X RE 1 Issue: 1.13 Replaces: 8.8 Sizes 1 to Maximum pressure 1 bar Displacement volume 1 to cm 3 Features Very short control times Low noise Mounting
More information