RA-N Valve Bodies with Pressfit Connection and Self-Sealing Tailpiece for Two Pipe Systems
|
|
- Peter Wheeler
- 5 years ago
- Views:
Transcription
1 Data Sheet RA-N Valve Bodies with Pressfit Connection and Self-Sealing Tailpiece for Two Pipe Systems Application Straight Angle The valve bodies with pressfit connection are used for heating systems with stainless steel or copper pipes. The fitting require a commercial compression tool. List of available tools is found on page 3. Horizontal angle Technical data are according to Euronorm EN 215. The valve bodies are equipped with a self sealing tailpiece featuring an O-ring seal. The valve bodies are physically and technically identical to RA-N, DN15 standard valves. All RA 2000 thermostatic sensors, as well as the new RAX design series, may be used as desired. Valve bodies are manufactured from DZR brass with nickel plating. The pressure pin of the gland seal is of chrominium steel and works in a lifetime lubricated O-ring. The complete gland seal can be replaced without draining down the system. The RA-N valve bodies with integrated presetting are used in two-pipe pumped heating systems. Flow is adjustable in the range m³/h. Should water treatment be used it is essential that dosing instructions of the manufacturer are strictly observed. It is recommended that formulations containing mineral oil are avoided. RA-N valve bodies are supplied with a red protective cap which can be used for manual regulation during the construction phase. The protective cap must not be used as a manual shut off device. A special manual shut off device (code no. 013G5000) should be used. Data and Ordering Type Design Connection Inlet Outlet Angle RA-N 15 Danfoss Heating Solutions Straight Horiz. angle Pressfit R½ With thermal actuator Code no. N(kvs) 013G3237 Xp= G3238 Xp= G3239 Settings, kv-values with RA 2000 sensor, m³/h 1) Xp VDUZL Danfoss / N 1
2 1) The k v -value indicates the water flow (Q) in m³/h at a pressure drop ( p) across the valve of 1 bar;. The k vs -value states the flow Q at a maximum lift, i.e. at fully open valve at setting N. At setting N the k v -value is stated according to EN 215, at X p = 2K i.e. the valve is closed at 2 C higher room temperature. At lower settings the X p -value is reduced to 0.5 K of the setting value 1 Accessories Product Code no. Gland seal, may be exchanged with system in operation O-Ring (5pcs.) 013G G4149 Approvals Danfoss RA-N pressfit valves are tested and approved according to EN 215. The O-rings used in the Danfoss pressfit valves bodies are according to EN 681. Pipes compatible with Danfoss pressfit valves are according to EN (welded stainless steel pipes ), EN (Thin-walled carbon steel pipes), EN 1057 (seemless copper pipes) with a minimum wall thickness of 1 mm. Presetting The calculated setting value can be set easily and accurately without using special tools: Remove the protective cap or sensor Raise the setting ring. Turn the scale on the setting ring until the desired value faces the reference mark, orientated towards the valve outlet Release the setting ring factory setting = N The presetting can be chosen from values between 1 and 7 with intervals of 0.5. At setting N the valve is completely open. A setting in the shaded area must be avoided. 1 When the sensor is mounted, the presetting is hidden and thus protected against unauthorized alteration. 1. Presetting area 2. Reference mark 2 Press System Pipes Copper and stainless stell pipes which complies to EN 1057 or EN Outer diametre and pipe weight according to EN 10312, Table 2 for serie 2 steelpipes. Danfoss recommends a pipe weight of min. 1 mm. Steel pipes 2 VDUZL502 Danfoss 02/2011 Danfoss Heating Solutions
3 Carbon steel pipes Tubes in unalloyed steel E195(W.nr ) and E235(W.nr ) according to EN or EN in condition +A or +N. Copper pipes Outer diametre and wall thickness according to EN 1057, Table 3. Danfoss recommends a minimal wall thickness of 1 mm. Pipe hardness min. R 290, meaning that only copper pipes in bars are compatible. No internal reinforcement is required. Compatibility The pressable area of Danfoss Pressfit valves are designed to match a range of commercial press tools and jaws as described in the table. For tools not mentined please check the with the manufacturer. Compatible press tools Press tools and jaws must be used and serviced as described by their manufacturer, and the actual press operation must be inspected. Danfoss require a minimal press force of 30 kn. The actual pressing must not be interrupted and the tool should be locked for removal until the pressing has been completed correctly. The testing of the press points is done according to the manufactures specs. Geberit Mapress: PWH 75, EFP2, ECO1/ACO1, EFP3, AFP3, ACO 3 REMS: Power-Press E, Power-Press 2000, Power- Press (ACC), Akku-Press (ACC) Rothenberger: ROMAX Pressliner, ROMAX Pressliner ECO, ROMAX AC ECO SANHA: ECO201, ACO201, ACO3, ECO301 Viega: PT3-EH, PT3-AH, Picco, Typ 2 Novopress: AFP 101 RIDGID: CT-400, 320-E Klauke: UAP2, UNP2, UP2EL-14 Compatible press jaws Mapress Geberit: Press jaws15 mm (90532) REMS: V15 (570115), M15 (570110), SA15 (570935) Rothenberger: SV 15 mm (1.5212X), M 15 mm (1.5102X) SANHA: Standard, 15 mm ( , ) Viega: PT2 15mm (Modell , Typ ) Novopress: M 15 RIDGID: ProPress 15 mm (16958) Klauke: KSP3 M15 mm, KSP4 V15 mm With system under pressure all pressfit connections should be inspected. Even if no leakage is seen the connection should be checked. Compatible press tools Danfoss Heating Solutions VDUZL502 Danfoss 02/2011 3
4 Fitting VDUZL502 Danfoss 02/2011 Danfoss Heating Solutions
5 Capacity RA-N 15 - capacities in combination with RA 2000 sensor at P band between 0.5 K and 2K The P band is the change in room temperature which is required to move the valve from closed position to the position which allows the calculated flow. Alternatively the setting can be read directly in the table "Data and Ordering": Sizing example Required heat: Cooling across radiator: Flow through radiator: Pressure drop across valve: 0.7 kw 20 C p = 1 mwg Valve setting: 2.5 Design Gland seal 2. O-Ring 3. Pressure pin 4. Seal 5. Regulation spring 6. Setting dial 7. Valve body 8. Union nut 9. Nipple 10. Pressfit connection 10 Danfoss Heating Solutions VDUZL502 Danfoss 02/2011 5
6 Materials in contact with water Valve body and other metal parts K v -limiter O-Ring Valve cone Ms 58, DZR brass PPS EPDM NBR Pressure pin and valve spring Nozzle Chrome steel PP The radiator thermostats consist of the thermostatic elements of the RA 2000/RAX series and the valve body. The element and the valve body are ordered separately. The valve bodies are nickle-plated on the outside. Dimensions ISO 7/1 - R1/ SW SW Dimensions with RA 2990 or RAX thermostatic sensor. 6 VDUZL502 Danfoss 02/2011 Danfoss Heating Solutions
7 Danfoss Heating Solutions VDUZL502 Danfoss 02/2011 7
8 Danfoss A/S Heating Solutions Haarupvaenget Silkeborg Denmark Phone: Fax: Danfoss can accept no responsibility for possible errors in catalogues, brochures and other printed material. Danfoss reserves the right to alter its products without notice. This also applies to products already on order provided that such alterations can be made without subsequential changes being necessary in specifications already agreed. All trademarks in this material are property of the respective companies. Danfoss and the Danfoss logotype are trademarks of Danfoss A/S. All rights reserved. 8 VDUZL502 Danfoss 02/2011 Danfoss Heating Solutions
Valve bodies with pressfit connection and self-sealing tailpiece. Type RA-N for two pipe systems
Valve bodies with pressfit connection and self-sealing tailpiece. Type RA-N for two pipe systems EN 215 Application Straight Angle Horizontal angle The valve bodies with pressfit connection are used for
More informationLockshield valves with Pressfit connection Type RLV with isulation and regulation
Data sheet Lockshield valves with Pressfit connection Type RLV with isulation and regulation Application RLV Straight pattern RLV Angle pattern Drain-cock The valve bodies with pressfit connection are
More informationValve bodies type RA-N with integrated presetting
Data Sheet Application Straight version Angle version Left mounted angle version Horizontal angle version All RA-N valve bodies can be used together with all types of thermostatic elements in the RA 2000
More informationIntegrated Valve with Presetting for Manifolds in Two-Pipe Heating Systems
Data Sheet Integrated Valve with Presetting for Manifolds in Two-Pipe Heating Systems The integrated valve is designed for manifold applications in combination with a system connection piece. Valve and
More informationDynamic Valve Type RA-DV Pressure Independent Radiator Valve
Dynamic Valve Type RA-DV Pressure Independent Radiator Valve Application RA-DV straight version RA-DV angle version RA-DV angle Right & Left RA-DV UK (Axial) RA-DV is a series of pressure independent radiator
More informationHigh Capacity Valve Body, Type RA-G
Data Sheet The RA-G valves are fitted with a grey protective cap. This protective cap must not be used as a manual shut off device. A special manual shut off device is available (code no. 013G3300). Application
More informationIntegrated Presetting Valves for Normal (013G0380) and Small (013G0381) Volume Flows
Integrated Presetting Valves for Normal (013G0380) and Small (013G0381) Volume Flows Application Integrated valves, type RA-N (013G0380) and RA- U (013G0381), with built-in presetting are designed for
More informationIntegrated Presetting Valves - for Normal Volume Flows RA-N and for Small Volume Flows RA-U
Integrated Presetting Valves - for Normal Volume Flows RA-N and for Small Volume Flows Application RA-N 013G7382 013G7387 Integrated valves, type RA-N 013G7382 and 013G7387, with built-in presetting are
More informationX-tra Collection for designer radiators and bathroom towel rails
and bathroom towel rails Application The new X-tra Collection is a TRV specially designed for towel rails and designer radiators. Its new and innovative self-sealing ½" valve to radiator connection makes
More informationHigh capacity valve body, type RA-G
Application The RA-G valves are fitted with a grey protective cap. This protective cap must not be used as a manual shut off device. A special manual shut off device is available (code no. 013G3300). The
More informationPressure relief controller AVA (PN 25)
Data sheet Pressure relief controller AVA (PN 25) Description AVA is a self-acting pressure relief controller primarily for use in district heating systems. The controller is normally closed and opens
More informationFloor heating system, heating circuit with FHV-A in flow.
Application FHV control valves are ideally suited for controlling the temperature of individual under-floor heated rooms and for systems using floor-heating in conjunction with radiators. Danfoss offers
More informationPressure reduction controllers (PN 25) AVDS - for steam AVD - for water
Data sheet Pressure reduction controllers (PN 25) - for steam AVD - for water Description Main data AVD: DN 15-50 k VS 0,4-25 m 3 /h PN 25 Setting range: 1-5 bar / 3-12 bar Temperature: - Circulation water/glycolic
More informationTemperature controller AVT with safety temperature monitor STM/VG(F) (PN25)
Data sheet Temperature controller AVT with safety temperature monitor STM/VG(F) (PN25) Description Controller closes on rising temperature. TR1240 The controllers are: Type-tested acc. to EN 14597 and
More informationFlow controller (PN 25) AVQ - return and flow mounting
Data sheet Flow controller (PN 5) - return and flow mounting Description is a self-acting flow controller primarily for use in district heating systems. The controller closes when set max. flow is exceeded.
More informationCombined automatic balancing valve AB-PM valve DN 10-32, PN 16
Data sheet Combined automatic balancing valve AB-PM valve DN 10-32, PN 16 Description AB-PM is a combined automatic balancing valve. It features three function in compact valve body: 1. Differential pressure
More informationFlow-compensated temperature controller AVTQ DN 15
Data sheet Flow-compensated temperature controller AVTQ DN 15 Description AVTQ is a self-acting flow-compensated temperature controller primarily for use in district heating systems with plate heat exchangers
More informationFlow controller with integrated control valve (PN 16) AHQM - return and flow mounting
Flow controller with integrated control valve (PN 16) AHQM - return and flow mounting Description Controllers are used together with Danfoss electrical actuators: DN 15-32 with - AMV(E) 10 - AMV(E) 13
More informationX-tra Collection for designer radiators and bathroom towel rails
and bathroom towel rails Application The new X-tra Collection is a TRV specially designed for towel rails and designer radiators. Its new and innovative self-sealing ½" valve to radiator connection makes
More informationPressure independent control valve with integrated flow limiter AVQM (PN 16) - return and flow mounting
Data sheet Pressure independent control valve with integrated flow limiter AVQM (PN 16) - return and flow mounting Description Controllers are used together with Danfoss electrical actuators: AMV 0 1)
More informationManual presetting valve MSV-C
Description / Application MSV-C is used for balancing the flow in cooling, heating and domestic water systems. MSV-C is a combined manual presetting valve with following features: Fixed measurement orifice.
More informationManual presetting valves LENO MSV-BD
Manual presetting valves LENO MSV-BD Description LENO MSV-BD is a range of manual valves for balancing flow in heating, cooling and domestic hot water systems. LENO MSV-BD is a combined presetting and
More informationPressure relief controller AFA / VFG 2(1) (PN 16, 25, 40)
Data sheet Pressure relief controller AFA / VFG 2(1) (PN 16, 25, 40) Description The controller is a self-acting pressure relief controller primarily for use in district heating systems. The controller
More informationHorizontal Distribution Units - HDU Multi-port
Application Danfoss pre-fabricated HDU distribution units are made for distribution and measuring of waterbased heating in 2-pipe horizontal systems. A HDU is easily mounted on the apartment wall and connected
More informationFHV control valves are flexible to use, easily installed and are available in two versions:
FHV-A/FHV-R Application: FHV-A FHV-R The floor-heating valve (FHV) provides an economical method of incorporating a radiant floor heating system into an existing hot water or radiator system. FHV self-acting
More informationPre-Fabricated Flushing Bypass Assembly for Plant Applications Hero Plant DN15-150
Pre-Fabricated Flushing Bypass Assembly for Plant Applications Description Hero Plant is a pre-fabricated, flushing bypass arrangement for balance, control, isolation, and operation of plant devices. Flow
More informationManual Presetting Valves LENO MSV-B
Data Sheet Description LENO MSV-B is a new generation of manual valves for balancing flow in heating, cooling and domestic hot water systems. LENO MSV-B is a combined presetting and shut off valve with
More informationThermostatic actuator RAVI - for 2-way valves RAV-/8 (PN 10), VMT-/8 (PN 10), VMA (PN 16)
- for 2-way valves RAV-/8 (PN 10), VMT-/8 (PN 10), VMA (PN 16) Description RAVI is self-acting thermostatic actuator primarily for use for temperature control of small hot water cylinders - either storage
More informationAutomatic balancing valves ASV-PV DN (3rd gen.)
Automatic balancing valves ASV-PV DN 50-100 (3rd gen.) Description / Application Partner valve ASV-PV DN 50 ASV-PV DN 65-100 MSV-F2 DN 50-100 ASV balancing valves are used for dynamic hydronic balance
More informationAssisted lift operated 2/2-way solenoid valves Type EV251B
Data sheet Assisted lift operated 2/2-way solenoid valves Type EV251B EV251B with assisted lift is especially suitable for applications such as closed systems with low and fluctuating pressure conditions
More informationSSM Floor Heating Manifold
Application The manifold consists of a supply and return manifold. The supply manifold includes possibility for individual shut-off of each circuit on flowmeter or shut-off valve. The return manifold is
More informationAVQMT. AVQT controller can be combined with AVT or STM thermostatic actuators.
Data sheet Flow and temperature controller with / without integrated control valve (PN 25) AVQT - flow and temperature controller AVQMT - flow and temperature controller with integrated control valve Description
More informationDifferential pressure controller with flow limitation and with integrated control valve (PN 16) AHPBM-F flow mounting, fixed setting
Data sheet Differential pressure controller with flow limitation and with integrated control valve (PN 16) AHPBM-F flow mounting, fixed setting Description The controller has a control valve with adjustable
More informationIntegrated valves Series 3
Series 3 Application For decades, Danfoss has been the world s leading manufacturer of radiator valves and radiator thermostats. Danfoss invented the radiator thermostat back in 1943 and later developed
More informationActuator type ABNM with Theft Protection, 0-10 V Proportional
Actuator type ABNM with Theft Protection, 0-10 V Proportional Application The ABNM actuator is a thermoelectric actuator for opening and closing valves in the fields of heating, ventilation and air conditioning
More informationTemperature controller for heating (PN 25) AVT / VG - external thread AVT / VGF - flange
Data sheet Temperature controller for heating (PN 25) AVT / VG - external thread AVT / VGF - flange Description AVT / VG AVT / VGF The AVT / VG(F) controller is a self-acting proportional temperature controller
More informationCombined automatic balancing valve AB-PM valve DN 15-25, PN 16
Data sheet Combined automatic balancing valve AB-PM valve DN 15-25, PN 16 Description AB-PM is a combined automatic balancing valve. It features three function in compact valve body: 1. Differential pressure
More informationDisassembling and assembling isave 21
MAKING MODERN LIVING POSSIBLE Service instruction Disassembling and assembling isave 21 isave.danfoss.com Table of Contents 1. General introduction....2 2. Disassembling the isave....3 3. Disassembling
More informationASSEMBLY INSTRUCTIONS
ASSEMBLY INSTRUCTIONS. General instructions for installing the pipe. Making a press connection. Making a repair. Making a screw connection. Making a screw/compression connection. Bending the HENCO pipe.
More informationV2000FS FS type TRV Body FINELY PRESETTABLE RADIATOR VALVE WITH FLUSH POSITION
V2000FS FS type TRV Body FINELY PRESETTABLE RADIATOR VALVE WITH FLUSH POSITION PRODUCT DATA Application 011 Angle to DIN Angle to NF Straight to DIN Straight to NF Thermostatic radiator valve bodies (TRV
More informationTemperature controller (PN 25) AVT / VG - external thread AVT / VGF - flange
Data sheet Temperature controller (PN 25) AVT / VG - external thread AVT / VGF - flange Description AVT / VG The AVT / VG(F) controller is a self-acting proportional temperature controller developed primarily
More informationSonoSensor 30 Ultrasonic flow sensor
Data Sheet SonoSensor 30 Ultrasonic flow sensor Description MID examination certificate no.: LT-1621- MI004-030 SonoSensor 30 is an ultrasonic flow sensor especially designed for heating, cooling or combined
More informationTemperature controller AVT with safety temperature monitor STM / VGS for steam (PN 25)
Data sheet Temperature controller AVT with safety temperature monitor STM / VGS for steam (PN 25) Description Controller closes on rising temperature. The controllers are: - Type-tested acc. to EN 14597
More information2 - way valve (NO), pressure relieved (PN 25) VG - external thread VGF - flange
Data sheet 2 - way valve (NO), pressure relieved (PN 25) VG - external thread VGF - flange Description VG and VGF are pressure relieved 2-way normally open (NO) valves, designed to be combined with: -
More informationFlow controller (PN 25) AVQ - return and flow mounting
Data sheet Flow controller (PN 5) - return and flow mounting Description is a self-acting flow controller primarily for use in district heating systems. The controller closes when set max. flow is exceeded.
More informationChanging pistons APP 21-43
MAKING MODERN LIVING POSSIBLE Instruction Changing pistons APP 21-43 ro-solutions.com Contents 1. Disassembling...3 2. Assembling...6 3. When should the pistons be replaced....8 4. Parts list for APP 21-38....9
More informationSonoSensor 30 Ultrasonic flow meter for heating and cooling applications
Installation & User Guide SonoSensor 30 Ultrasonic flow meter for heating and cooling applications 03/2017 Danfoss VDIGK202 www.heating.danfoss.com 1 Note! To ensure latest version of declaration, please
More informationTechnote. Frese OPTIMIZER - pressure independent 4-pipe coil control unit. Application. Benefits. Features.
Page of 7 Application control unit, in conjunction with the associated hydraulic set provides a complete pressure independent balancing and control group for efficient and effective individual room or
More informationSonoMeter 30 Energy Meters
SonoMeter 30 Energy Meters Description MID examination certificate no.: LT-1621-MI004-020 The Danfoss SonoMeter 30 is a range of ultrasonic, compact energy meters intended for measuring energy consumption
More informationPremounted Midi Shunts
Application Midi Shunt 088U0181 - with one circuit Midi Shunt 088U0182 - with two circuits Midi Shunt 088U0183 - with three circuits The Danfoss floor heating midi shunt is a series of pre-mounted shunts
More informationFlow controller with integrated control valve (PN 16) AHQM return and flow mounting
Data sheet Flow controller with integrated control valve (PN 16) AHQM return and flow mounting Description DN 15-32 DN 40, 50 DN 50-100 DN 125 DN 150 DN 200, 250 AHQM is a self-acting flow controller with
More informationChangeOver6 and NovoCon ChangeOver6 - Motorized 6-port Ball Valves
- Motorized 6-port Ball Valves Description NovoCon The and NovoCon are 6-port motorized ball valves that performs a diverting function between two water circuits in 4-pipe changeover system. This diverting
More informationFlow controller with integrated control valve (PN 16) AVQM - return and flow mounting
Data sheet Flow controller with integrated control valve (PN 16) AVQM - return and flow mounting Description The controller has a control valve with adjustable flow restrictor, connection neck for electrical
More informationSonoMeter 30 Energy Meters
SonoMeter 30 Energy Meters Description The Danfoss SonoMeter 30 is a range of ultrasonic, compact energy meters intended for measuring energy consumption in heating and cooling applications for billing
More informationData sheet Pressure independent control valve with integrated flow limiter AVQM (PN 16) - return and flow mounting
Pressure independent control valve with integrated flow limiter AVQM (PN 16) - return and flow mounting Description Controllers are used together with Danfoss electrical actuators: - AMV 150 1) - AMV(E)
More informationTwo- and three way valves VFG.. / VFGS 2 / VFU.. for self-acting thermostats and electrical actuators
for self-acting thermostats and electrical actuators Description VFG 2 VFG 21 (see pages 2, 3, 4) Valves for heating, district heating and cooling systems. The valves can be used with following actuators:
More informationMikrotherm F. Manual Radiator Valves With presetting
Mikrotherm F Manual Radiator Valves With presetting IMI HEIMEIER / Thermostatic Heads & Radiator Valves / Mikrotherm F Mikrotherm F The Mikrotherm F manual radiator valve is used in warm water pump heating
More informationTechnote. Frese OPTIMA Compact DN10-DN50 - pressure independent balancing & control valve. Application. Features. Benefits.
Page of 5 Frese OPTIMA Compact DN-DN5 Application Frese OPTIMA Compact pressure independent balancing & control valve (PIBCV) is used in heating and cooling systems in applications with Fan Coil Units,
More informationDifferential pressure controller (PN 16, 25, 40) AFP(-9) / VFG 2(1) return and flow mounting, adjustable setting
Data sheet Differential pressure controller (PN 16, 25, 40) AFP(-9) / VFG 2(1) return and flow mounting, adjustable setting Description The controller has a control valve, an actuator with one control
More informationCrankcase pressure regulator Type KVL
Data sheet Crankcase pressure regulator KVL Crankcase pressure regulator type KVL is fitted in the suction line ahead of the compressor. KVL protects the compressor motor against overload during start-up
More informationYour Personal Catalog Temperature Controllers All our know-how - is now yours
MAKING MODERN LIVING POSSIBLE Your Personal Catalog Temperature Controllers All our know-how - is now yours Index 3 RAVI 12 RAVK 20 RAVV 28 AFT 06/26/17/27 33 AVTB 41 AVTQ DN15 49 AVTQ DN20 57 FJV 61 STFW/VFG(S)
More informationRADIATOR VALVE ACCESSORIES
RADIATOR VALVES ACCESSORIES RADIATOR VALVES CONTENTS Accessories and spare parts: Presetting tools Radiator connections Other connections (FPL, FPL-PX, KOMBI - see each catalogue leaflet) Radiator unions
More informationON/OFF zone valves AMZ 112, AMZ 113
Data sheet ON/OFF zone valves AMZ 112, AMZ 113 Description The ON/OFF zone valves type AMZ 112 and AMZ 113 are typical used in connection with: Domestic and commercial central heating applications Domestic
More informationSpare parts Pipesystems / Pre-Wall Installation Catalogue 01/2018.
Spare parts Pipesystems / Pre-Wall Installation Catalogue 01/2018 www.friatec.de Informationen Content Product Discount Range Range Page Information 3 Spare parts Piping systems FRIATHERM rigid Bonding
More informationChanging pistons APP and APP 16-22
MAKING MODERN LIVING POSSIBLE Instruction Changing pistons APP 11-13 and APP 16-22 ro-solutions.com Contents 1. Disassembling...3 2. Assembling...5 3. When should the pistons be replaced?....7 This document
More informationINT 4/15 Catalogue 2015/2016 We reserve the right to effect changes. System press tools. Piping technology
INT 4/5 Catalogue 205/206 We reserve the right to effect changes. Piping technology P For all Viega press systems from d 2 08.0. Viega system press tools can be used with all metallic Viega press systems
More information2018 High Performance Check Valves for liquid and gaseous media
2018 High Performance Check Valves for liquid and gaseous media Check valves Catalogue 45 Date: 04/2018 WEH - We Engineer Hightech All rights reserved, WEH GmbH 2018. Unauthorized copies are strictly forbidden
More informationData sheet. D-2011/05/ Date: 07/2013. Type TK4 CNG. CNG Fuelling Nozzle. for cars. WEH - We Engineer Hightech
Data sheet D-2011/05/00160-4-3 Date: 07/2013 Type TK4 CNG CNG Fuelling Nozzle for cars WEH - We Engineer Hightech General Description Sliding sleeve Media inlet Features Compatible with receptacles acc.
More informationData sheet. D-2011/05/ Date: 07/2013. Type TK1 CNG. CNG Fuelling Nozzle. for time filling of cars. WEH - We Engineer Hightech
Data sheet D-2011/05/00160-4-3 Date: 07/2013 Type TK1 CNG CNG Fuelling Nozzle for time filling of cars WEH - We Engineer Hightech General Description Sliding sleeve Media inlet Features Compatible with
More informationOne. The performance of your wind turbine relies on the quality of its small components. ia.danfoss.com. Brochure Mobile Hydraulic
Brochure Mobile Hydraulic The performance of your wind turbine relies on the quality of its small components One stop shop - reducing your supply base and boosting your bottom line ia.danfoss.com Efficient
More informationCrankcase pressure regulator Type KVL
Data sheet Crankcase KVL KVL crankcase are used to protect the compressor motor against overload experienced during startup after long off periods or just after defrost periods. They are installed in the
More informationTRIM, TRIM A, RADITRIM A, TRIM K, STK, TA Loop
TOUR & ANDERSSON AB QUALITY AND ENVIRONMENT SYSTEM Certification of Registration Number 2125 and 2125 M Certified by SP TRIM, TRIM A, RADITRIM A, 1-15-5 TRIM K, STK, TA Loop Return valves and measurement
More informationELIMINATOR Hermetic bi-flow filter drier Types DMB and DCB
Data sheet ELIMINATOR Hermetic bi-flow filter drier s DMB and DCB Hermetic bi-flow filter driers, types DMB and DCB are for use in liquid lines on heat pumps. Hermetic bi-flow filter driers have built-in
More informationTechnote. Frese OPTIMA - Pressure independent control & balancing valve. Application. Features. Benefits.
Page 1 of 12 Application pressure independent control valve (PICV) is used in heating and cooling systems in applications with Fan Coil Units, Air Handling Units or other terminal unit applications. provides
More informationV2000BB BB type TRV Body RADIATOR VALVE WITH BROADBAND CARTRIDGE
V2000BB BB type TRV Body RADIATOR VALVE WITH BROADBAND CARTRIDGE PRODUCT DATA Angle to EN215 (D) 011 Straight to EN215 (D) Application Thermostatic radiator valve bodies (TRV bodies) are fitted on the
More informationDuct System for Danfoss Air Units
MAKING MODERN LIVING POSSIBLE Installation Guide for Danfoss Air Units www.heating.danfoss.com Danfoss A/S is not liable or bound by warranty if these instructions are not adhered to during installation
More informationVE-S_15-32 Pressure Independent Balancing & Control Valves
Page 1 of 9 VE-S_15-32 Pressure Independent Balancing & Control Valves (PIBCV) is used in heating and cooling systems in applications with Fan Coil Units, Chilled Beams or other terminal unit applications.
More information611, 671. Diaphragm Valve, Metal
Diaphragm Valve, Metal Construction The 611 and 671 manually operated 2/2-way metal diaphragm valves have a low maintenance plastic bonnet and an integral optical position indicator as standard. Features
More informationDifferential pressure relief controller (PN 16, 25, 40) AFPA / VFG 2(1)
Data sheet Differential pressure relief controller (, 25, 40) AFPA / VFG 2() Description The controller has a control valve, an actuator with one control diaphragm and spring for differential pressure
More information4-way Distribution Valve
4-way Distribution Valve for one- and two-pipe systems Product specification sheet Application 4-way distribution valves are used to connect supply and return of a radiator to the corresponding pipes of
More informationV2000Kx KV type TRV Body
V2000Kx KV type TRV Body RADIATOR VALVE WITH KV-SPECIALIZED CARTRIDGE PRODUCT DATA Angle to DIN Straight to DIN 011 Application Thermostatic radiator valve bodies (TRV bodies) are fitted on the supply
More informationPlease refer to our catalogue for details of the full product range
Thermostatic Radiator Valve Bodies Series V6 - Double Regulating Function ngle Pattern 118 37 63 118 37 64 11.10 11.10 EPDM disk & seals (see note below) F x MU ends Thermostat connection thread M30 x
More informationVZ*19* VZ219E, VZ319E, VZ419E VZ219C, VZ319C, VZ419C
VZ219E, VZ319E, VZ419E VZ219C, VZ319C, VZ419C SPECIFICATIONS Design PN16, Two-way, Three-way and Three-way with bypass (Linear operation) Function.... Normally Closed (A-AB). [Without actuator fitted]
More informationRTL. Floor Heating Controller Return temperature limiter with and without presetting
RTL Floor Heating Controller Return temperature limiter with and without presetting IMI HEIMEIER / Floor Heating Control / RTL RTL Among other things, the return temperature limiter RTL is used to limit
More informationDiaphragm Valve, Metal
Diaphragm Valve, Metal Construction The GEMÜ pneumatically operated 2/2-way diaphragm valve has a low maintenance membrane actuator which can be controlled by inert gaseous media. Normally Closed, Normally
More informationDiaphragm Valve, Metal
Diaphragm Valve, Metal Construction The GEMÜ pneumatically operated 2/2-way diaphragm valve has a low maintenance actuator. Normally Closed, Normally Open and Double Acting control functions are available.
More informationDiaphragm Valve, Metal
Diaphragm Valve, Metal Construction The GEMÜ motorized metal diaphragm valve has a low maintenance electric actuator and a reversible synchronous motor. It is operated via a reduction gear and cam. The
More informationSeated valves (PN 16) VRB 2 2-way valve, internal and external thread VRB 3 3-way valve, internal and external thread
Data sheet Seated valves (PN 16) VRB 2 2-way valve, internal and external thread VRB 3 3-way valve, internal and external thread Description VRB valves provide a quality, cost effective solution for most
More informationThe precise step to take
New perspectives with Danfoss Saginomiya Electronic Expansion Valves The precise step to take Type KV Electronic Expansion Valves Energy efficiency Precision flow control with high resolution Compact and
More informationPANEL RADIATORS. Price list valid from March 01, 2018
PANEL RADIATORS MADE IN YEARS POLAND WARRANT Y 1 Price list valid from March 01, 2018 2 CONTENT PERFEKT panel radiators compact radiators valve radiators retrofit radiators style radiators hygienic radiators
More informationReliable season change
New perspectives with Danfoss Saginomiya 4 - Way Reversing Valves Reliable season change, VHV 4-way reversing valves Wide application range - complete capacity range - available for all common refrigerants
More informationTel: +44 (0) E mail: Web: Data sheet. APP pumps APP ro-solutions.com
APP pumps APP 53-78 Tel: +44 (0) 1706 869777 E mail: sales@desal.co.uk Web: www.desal.co.uk ro-solutions.com Table of Contents 1. Introduction...3 2. Benefits...3 3. Application examples...3 4 Technical
More informationDatA sheet. D-2011/05/ Date: 02/2013. Type TK10 CNG. CNG Fuelling Nozzle. for cars FUTURE. TECHNOLOGY. TODAY.
DatA sheet D-2011/05/00160-3-3 Date: 02/2013 Type CNG Fuelling Nozzle for cars FUTURE. TECHNOLOGY. TODAY. Type Fuelling nozzle for cars General Description Ball valve Sliding sleeve 1 Hand grip TK4 CNG
More informationthree-way mixing valve
three-way mixing valve with or without presetting, for heating and cooling systems. Pressurisation & Water Quality alancing & Control Thermostatic Control engineering avantage Three-way mixing valve, with
More informationButterfly valve with electrical actuator VFY-WA
Butterfly valve with electrical actuator Description Position indicator Torque limiter Complete installation from factory - ready for installation Features: Spline driven one piece shaft connected to spherically
More informationButterfly valve with electrical actuator VFY-WA
Butterfly valve with electrical actuator Description Position indicator Torque limiter Complete installation from factory - ready for installation Features: Spline driven one piece shaft connected to spherically
More informationInfocal 9 Energy calculator for heating and cooling applications
Installation & User Guide Infocal 9 Energy calculator for heating and cooling applications www.danfoss.com 2 Danfoss Energy Meters 2017.03 VUIGN102 1. Installation 1.1. Preparation Only qualified personnel
More informationThermostatic valve Type AVTA
SALES SERVICE +358 (0)17 262 3555 info@econosto.fi MAKING MODERN LIVING POSSIBLE Data sheet Thermostatic valve Type AVTA Thermostatic valves are used for proportional regulation of flow quantity, depending
More information611, 671. Diaphragm Valve, Metal
Distributed by: Tel: 905.677.9000 Toll Free: 1.0.486.7863 www.tricanada.com Diaphragm Valve, Metal Construction The 611 and 671 manually operated 2/2-way metal diaphragm valves have a low maintenance plastic
More informationAPP pumps APP / APP / APP / APP (W) / APP / APP / APP 21-43
Data sheet Data sheet APP Pumps APP 0.6-1.0 / APP 1.5-3.5 / APP (W) 5.1-10.2 / APP 11-13 / APP pumps APP 16-22 0.6-1.0 / APP / 21-43 APP 1.5-3.5 / APP (W) 5.1-10.2 / APP 11-13 / APP 16-22 / APP 21-43 ro-solutions.com.
More information