1 Single Zone Unitary Infrared Radiant Systems.

Size: px

Start display at page:

Download "1 Single Zone Unitary Infrared Radiant Systems."

Millicent Jones
5 years ago
Views:

2 1 Single Zone Unitary Infrared adiant Systems. Smartom Mulitizone LIVE 1/L 2/N 10 S/0S/1 D0 D1 O0 O1 B1 B0 B (EMOTE ON) (OMMON) (EMOTE OFF) 15 amp Supply NOTES: EMOTE SWITH INPUTS should be connected by 18 Awg cable. Max length is 325ft. Low voltage switching inputs to be normally open (closed circuit to enable). onnect to B0 & B1 for remote ON (ie BMS time control). onnect to B0 & B2 for remote OFF (ie door interlock. remote frost etc). EMOTE SENSO(s) may be placed at a max distance of 325ft from the control unit, using shielded 18 Awg cable. Wiring should be kept separate from mains wiring to minimize noise pick up. Set within Engineers functions for any remote sensor. Drawing No. : USA

3 2 Single Zone Infrared Herringbone Fan Systems. Smartom Mulitizone LIVE 1/L 2/N 10 S/0S/1 D0 D1 O0 O1 B1 B0 B S amp Supply NOTES: EMOTE SWITH INPUTS should be connected by 18 Awg cable. Max length is 325ft. Low voltage switching inputs to be normally open (closed circuit to enable). onnect to B0 & B1 for remote ON (ie BMS time control). onnect to B0 & B2 for remote OFF (ie door interlock. remote frost etc). EMOTE SENSO(s) may be placed at a max distance of 325ft from the control unit, using shielded 18 Awg cable. Wiring should be kept separate from mains wiring to minimize noise pick up. Set within Engineers functions for any remote sensor. Drawing No. : USA Exhaust Fan

4 3 Multizone Unitary Infrared adiant Systems. (EMOTE ON) (OMMON) (EMOTE OFF) Smartom Mulitizone Smartom Mulitizone LIVE LIVE 1/L 2/N 10 S/0S/1 D0 D1 O0 O1 B1 B0 B /L 2/N 10 S/0S/1 D0 D1 O0 O1 B1 B0 B (EMOTE ON) (OMMON) (EMOTE OFF) NOTES: NETWOK. Master-slave (Network) communication is by shielded twisted pair cable, S485 compatible such as Belden Maximum overall system length of 1650ft onnect screen to 0. NOTE: Diagram shows a master and ONE slave configuration**. Wire further slaves in parallel. EMOTE SWITH INPUTS should be connected by 18 Awg cable. Max length is 325ft. Low voltage switching inputs to be normally open (closed circuit to enable). onnect to B0 & B1 for remote ON (ie BMS time control). onnect to B0 & B2 for remote OFF (ie door interlock. remote frost etc). For Master/Slave networks, remote OFF can be set for individual zones or total system via the Master. If individual BMS ON/OFF on master/slaves systems are required, set all Smartom programs to 24 hour and use normally closed contacts across B0 and B2. Set engineers variable. EMOTE SENSO(s) may be placed at a max distance of 325ft from the control unit, using shielded 18 Awg cable. Wiring should be kept separate from mains wiring to minimize noise pick up. Set within Engineers functions for any remote sensors. Zone B Zone A (Slave 1) (Master) 15 amp Supply 15 amp Supply Drawing No.: USA

5 4 Split Zone Infrared Herringbone Fan Systems. Smartom Mulitizone (Master) LIVE 1/L 2/N 10 S/0S/1D0 D1 O0 O1 B1 B0 B (EMOTE ON) (OMMON) (EMOTE OFF) NOTES: NETWOK. Master-slave (Network) communication is by shielded twisted pair cable, S485 compatible such as Belden Maximum overall system length of 1650ft onnect screen to 0. NOTE: Diagram shows a master and ONE slave configuration**. Wire further slaves in parallel. EMOTE SWITH INPUTS should be connected by 18 Awg cable. Max length is 325ft. Low voltage switching inputs to be normally open (closed circuit to enable). onnect to B0 & B1 for remote ON (ie BMS time control). onnect to B0 & B2 for remote OFF (ie door interlock. remote frost etc). For Master/Slave networks, remote OFF can be set for individual zones or total system via the Master. If individual BMS ON/OFF on master/slaves systems are required, set all Smartom programs to 24 hour and use normally closed contacts across B0 and B2. Set engineers variable. EMOTE SENSO(s) may be placed at a max distance of 325ft from the control unit, using shielded 18 Awg cable. Wiring should be kept separate from mains wiring to minimize noise pick up. Set within Engineers functions for any remote sensors. Exhaust Fan Zone A Smartom Mulitizone LIVE (EMOTE ON) (OMMON) (EMOTE OFF) Zone B S-0755 W1 (Slave 1) 1/L 2/N 10 S/0S/1D0 D1 O0 O1 B1 B0 B amp Supply 20 amp Supply Drawing No. : USA

6 5 Multizone Infrared Herringbone Fan Systems. NOTES: NETWOK. Master-slave (Network) communication is by shielded twisted pair cable, S485 compatible such as Belden Maximum overall system length of 1650ft onnect screen to 0. NOTE: Diagram shows a master and ONE slave configuration**. Wire further slaves in parallel. EMOTE SWITH INPUTS should be connected by 18 Awg cable. Max length is 325ft. Low voltage switching inputs to be normally open (closed circuit to enable). onnect to B0 & B1 for remote ON (ie BMS time control). onnect to B0 & B2 for remote OFF (ie door interlock. remote frost etc). For Master/Slave networks, remote OFF can be set for individual zones or total system via the Master. If individual BMS ON/OFF on master/slaves systems are required, set all Smartom programs to 24 hour and use normally closed contacts across B0 and B2. Set engineers variable. EMOTE SENSO(s) may be placed at a max distance of 325ft from the control unit, using shielded 18 Awg cable. Wiring should be kept separate from mains wiring to minimize noise pick up. Set within Engineers functions for any remote sensors. Exhaust Fan Exhaust Fan Zone A Smartom Mulitizone (Master) LIVE 1/L 2/N 10 S/0S/1 D0 D1 O0 O1 B1 B0 B (EMOTE ON) (OMMON) (EMOTE OFF) S-0755 W1 Smartom Mulitizone LIVE 1/L 2/N 10 S/0S/1 D0 D1 O0 O1 B1 B0 B (EMOTE ON) (OMMON) (EMOTE OFF) N L Zone B S-0755 W1 (Slave 1) 20 amp Supply 20 amp Supply Drawing No. : USA

7 6 Schematic - 2 Zone, 1 Fan Herringbone System. Burner 2 Burner 2 Burner 1 115V 60Hz Mains Supply Fan entre Heater 18 Awg Shielded able Smartom³ no.1 'MASTE' (S3-MZ) Zone A Air (optional) Tail Pipe Burner 3 Burner 2 115V 60Hz Mains Supply Heater Networking able Shielded pair Beldon 9841 or equiv 1 phase 115V Exhaust Fan Burner 1 18 Awg Shielded able Zone B Smartom³ no.2 'SLAVE' (S3-MZ)

8 7 Smartom³ adiant ommissioning. For ease and swiftness of initial start-up, the Smartom³ range of electronic is supplied factory pre-set to default settings as described in the Smartom³ Installation and User Manual ref US/SOM/29. The will therefore operate immediately with standard Infrared adiant heaters without the need for on-site programming. However, if either multi-zone Infrared, single or multi-zone Herringbone or single or multi-zone A systems are to be operated along with a, then the engineers settings will have to be modified.

Notes: MASTE & SLAVE (NETWOK) When setting up a Smartom³ Master and Slave (Network) system, the master controller will display an error message during commissioning.

9 Notes: MASTE & SLAVE (NETWOK) When setting up a Smartom³ Master and Slave (Network) system, the master controller will display an error message during commissioning. This will clear once the commissioning is complete. Th 09 : 30 Zone 1 OMMS E Zone 6 EMOTE SWITHED INPUTS B. emote Door Interlock EXTENAL / DOO FOST ONLY Smartom³ can be connect to a door interlock, remote frost stat or permanent off switch via terminals B2 and B0. When a volt free connection is provided (ie closed circuit to enable) at these terminals, the controller reverts to a FOST ONLY mode. efer to the individual wiring diagrams for wiring configurations and type. Smartom³ can be operated remotely via a remote ON or a remote OFF signal in the following ways: A. Building Management System ontrol (BMS). EXTENAL / BMS AUTO Smartom³ can be operated via a BMS system, by applying a volt free connection (ie closed circuit to enable) across terminals B1 and B0 turns the system on. Making this connection on a master controller will turn the entire system on whereas making this connection on a slave unit will only bring on that zone. 1. BMS ontrolling Time only. Ensure all the programmed ON times in the Smartom³ are turned off (i.e. They read - -:- - ). 2. BMS ontrolling Time and Temperature. Ensure all the programmed ON times in the Smartom² are turned off (i.e. They read - -:- - ). Set all the required day temperatures to 30.

10 Your Local epresentative Document reference number B/ON/30/0311 Ambi-ad Limited P.O. Box 617 Fishers, Indiana Telephone Facsimile Website For the Distributor Nearest please call Ambiad is a registered trademark of Ambiad Limited. Because of continuous product innovation, Ambiad reserves the right to change product specification without due notice.

R1000 Series Relays. Features and Benefits. Enclosed Relay Contacts Delivers maximum durability and extends life; inhibits corrosion and dust build-up

R1000 Series Relays. Features and Benefits. Enclosed Relay Contacts Delivers maximum durability and extends life; inhibits corrosion and dust build-up Master atalog 125 s and ontactors Section R Product Bulletin R1000 Issue Date 0493 R1000 Series s The R1000 Series s switch line voltage devices from low voltage controllers. Plug-in DPDT relays and snap-in