IP44 STM61A IP67 STM13A IP44 STM63A IP67 STM31A IP44 STM81A IP67 STM33A IP44 STM83A IP67 STMB11A IP44 STM35A STM12A IP44 STM62A IP67 STM14A

Transcription

1 Stopper Bolt with a Built-in STM Machine Components with a Built-in series Seating check plunger type Mini type US.PAT. STM11A STM61A STM13A STM31A STM81A 88 (the smallest) Mini-stopper with a built-in switch Mini switch with a hardened stopper surface Best suited to demanding application and equipment for installation space. There are straight touch type and angled touch type. STM82A STM32A Friction-less plate spring is applied to this product STM36A STM34A Protective structure (Water-resistant type) As for water-resistant type, the stopper surface is stored in the rubber boot. Standard product name Shape Short type Non-threaded type Non-threaded type with flange Threaded type Threaded type with flange Non-threaded/ threaded with a contacting ball type Non-threaded type threaded type with flange Standard product name Protective structure STM11A STM61A STM13A STM63A STM31A STM81A STM33A STM83A STMB11A STM35A STM12A STM62A STM14A STM64A Long type Threaded type STM32A STM82A Threaded type STM34A with flange STM84A Non-threaded/ threaded with a STMB12A contacting ball type STM36A When stopper property is not required, CS-Touch CSM with 1.5mm stroke is recommended. (Refer to P4-7) High dimensional accuracy for mounting Simple setting at replacement. L L : Mounting dimension unit:mm Contact force Size M108 M with LED STM11A-L STM61A-L STM13A-L STM63A-L STM31A-L STM81A-L STM33A-L STM83A-L 811 STMB11A-L M1011 STM35A-L M1015 M STM12A-L STM62A-L STM14A-L STM64A-L STM32A-L STM82A-L STM34A-L STM84A-L STMB12A-L M1018 STM36A-L -L : LED indicator (120mm from the switch) 5-8

2 STM Seating check plunger type Mini type Machine Components with a Built-in series Stopper Bolt with a Built-in Common specification structure Output mode Signal point Repeatability Movement differential Contact life time Withstand load Impact resistance Case and stopper surface material Contacting part material *1 Operating speed slower than 10mm/min is not recommended. How to use Dry contact A : Normally open Middle of the stroke Both OnOff, OffOn/ 0.01 (At operating speed 50200mm/min)* million (See before 3-4) 3000N 1500N : In the case the contacting surface of the detected object is smaller than f6 and the selected sensor is (STM11STM36) 0.2J SUS HRc45 SUS HRc50 Cable (Refer to P2-4) Operating temperature range Temperature drift Oscillation Impact Contact rating Standard accessory Circuit diagram No LED Normally open(no) Short type : Core-wire cable m(2) Oil-resistant 0.6 Tensile strength 15N Long type : Cabtyre cable 2m Oil resistant 2.8 / 2 cores, Tensile strength 30N 0 C80 C (Ice-free)* Hz total amplitude 1.5 for X,Y,Z each direction 300m/s 2 for X,Y,Z each direction DC5VDC24V 10mA (MAX20mA) Resistance load Refer to the drawing *2 The sealed waterproof structure, when used under temperature (below 5C) causes delay in return. Brown Blue with LED Normally open(no) LED Normally Off unit:mm Brown+ Blue- Contacting ball type Suitable for anglular touch within 3 Other types Make contact with the object at right angle (within deflection angle ±2 ) Slipping after push-in Electrical specification / circuit diagram. (Refer to P2-1) CL type interface unit cannot be used with LED. When using the switches with LED option, limit the current below 10mA. Installing instruction The angle required to turn on the switch when the object can not make contact with the switch end. Do not press the plunger beyond the stopper. It may cause malfunction due to the impact. If there is possibility to press the plunger to the stroke end, install a separate stopper to prevent malfunction. (The contact surface of the objects should be more than 3.5mm in diameter for drip-proof type) Explanatory diagram Drip-proof type () 1) When using under the specified static load resistance, the stopper surface of the product can be used as a stopper. Do not let dust or metal cuttings pile up on the stopper surface when using drip-proof type 2) When the expected load is larger than the specification, embed the switch in a sturdy stopper (to be prepared by the customer) for use. (Not provided) Free contact position Signal point (Middle of the stroke) Contacting part Rubber diaphragm How to install Non-threaded type Threaded type Mounting dimension Water-resistant type () SR2.5 2 Free contact position Signal point (Middle of the stroke) Contacting part Rubber boot (In the rubber boot) Set screw Proportionate tightening Non-threaded type with flange Bonding Sandwiching Screw in Threaded type with flange Mounting dimension M12 The products in this series are not suitable for operating in a harsh machining environment (even type) where coolant contains metal cuttings. Set screw Nut tightening Screw in 5-9

3 STM Seating check plunger type Mini type Outer dimension Straight touch type Short type (Core-wire cable) Non-threaded type Non-threaded type with flange Threaded type Threaded type with flange Non-threaded type Threaded type Drip-proof type () STM11A (A : NO) STM13A (A : NO) STM31A (A : NO) Accessory : Spanner 1, nut 1 STM33A (A : NO) Outer dimension Angled touch type (Contacting ball) Short type (Cable : Core-wire cable) STMB11A (A : NO) STM35A (A : NO) Machine Components with a Built-in series Stopper Bolt with a Built-in Water-resistant type () STM61A (A : NO) STM63A (A : NO) V-Groove 90 V-Groove 90 Flat portion 4.5 S3 ball S3 ball Flat portion Flat portion 11 ± ±0.03 M STM81A (A : NO) Accessory : Nut 1 STM83A (A : NO) Long type (Cable : Cabtyre) STMB12A (A : NO) Flat portion 4.5 S3 ball 18 STM36A (A : NO) S3 ball ±0.03 M Material : BsBM Treatment : N i plating Product name : S623B M Accessory : Spanner 1, nut 1 Accessory : Spanner 1, nut 2, toothed washer 5-10

4 STM Seating check plunger type Mini type Outer dimension Straight touch type Long type (Cabtyre cable) Drip-proof type () Machine Components with a Built-in series Stopper Bolt with a Built-in Water-resistant type () Non-threaded type Non-threaded type with flange Threaded type Threaded type with flange STM12A (A : NO) STM62A (A : NO) STM14A (A : NO) STM64A (A : NO) V-Groove 90 V-Groove 90 STM32A (A : NO) STM82A (A : NO) M M Accessory : Spanner1, nut2, toothed washer Accessory : Nut2, toothed washer STM34A (A : NO) STM84A (A : NO) M101.5 M101.5 Flat portion (-L: LED indicator) with LED 120 (25) LED lamp

5 Electrical specification Output specification Contact type with dry contacts for switching part Block diagram structure Control device Contact type with dry contacts for switching part Options for output specification Interface unit (P2-2) Level conversion Increase of output current protection PLC CNC *Write the corresponding product number when placing orders.(refer to P2-2) Specification Contact rating DC+5VDC+24V 10mA (MAX20mA) Resistance load ( without LED,DC1V-24V possible) Insulation resistance More than 100MΩ with DC250V Megger Output mode A : Normally open or B : Normally close Refer to P6-3 about how to use switches under the condition of AC100V-200V. Circuit diagram High-accuracy MT-Touch 1-signal type (Old wire color ) CS-Touch and others (Other sensors 1-signal types) (Old wire color ) without LED with LED without LED with LED Normally open (NO) Brown (Red) Blue (White) Normally open (NO) LED Normally Off Brown (Red)+ Blue (White)- Normally open (NO) Brown (Red) Blue (White) Normally open (NO) LED Normally Off Brown (Red)+ Blue (White)- Normally close (NC) Normally close (NC) Normally close (NC) Normally close (NC) Brown (Red) Brown (Red)+ Brown (Red) Brown (Red)+ Blue (White) Blue (White)- Blue (White) Blue (White)- LED Normally On LED Normally On When using the switches with LED option, limit the current below 10mA. How to replace currently using proximity switches (3-core and 2-core type) with METROL (2-core type) NPN output Brown (+) METROL Blue (-) contact switches +524V 0V (Brown) (Black) (Blue) Proximity switches etc. (3-core type 2-core type) 3-core type 2-core type PNP output Brown (+) Blue (-) METROL contact switches +524V 0V (Brown) (Black) (Blue) Proximity switches etc. (3-core type 2-core type) 2-core type 3-core type 2-1

6 Electrical specification Interface unit Interface unit Electrical specification Power supply voltage Power consumption Input Output Operating temperature range DC24V ±10% (Full-wave rectification with ripple 5% or less) 30mA One contact signal Transfer output (in-phase or inverted output) 0 C50 C When using the switches (except MT-Touch ) with the interface unit, the option for the LED attached on the switch is not available. The diode is attached in parallel to the LED for MT-Touch for the cases where the switch is used with the interface unit. No diode is attached to the switches except for MT-Touch. Characteristics 1) Protection for the dry contacts from inrush current The interface unit is not needed, when using the switches under the contact rating. The switch side of the interface unit has high-frequency alternating current control and it reduces the influence of sparks and chattering caused by vibration. Being separated from I/O circuit, the dry contacts of the switches remain intact from sudden inrush current. 2) Increase the output current (except photo coupler type) Enable to drive a relay or similar devices directly. When driving a relay by this unit, the repetitive accuracy would be lowered due to delay of the relay. 3) Level conversion unit Level conversion (normally close to normally open, normally open to normally close) Output specification Product name Output method CL- NPN-TR CL-1P PNP-TR CL-1FT Photo coupler CL-1F CL-1FH Photo Mos relay Diagram Output level 0V sink 24V source No-voltage floating output Output capacity DC24V 100mA 350mW DC30V 20mA 120mW AC/DC60V 100mA 240mW AC/DC200V 100mA 240mW Operating time Delay Spread 100µsec (Representing value) 20100µsec 500µsec(Representing value) 1020µsec Outer dimension In-phase 1 4 Inverted output 5 8 output DC24V + [VOTTOM.VEW] - input + Connecting diagram with electrical load CL- CL-1P input CL-1FT input Main circuit Main circuit Terminal layout In-phase Inverted In-phase Inverted for DC circuit DC circuit input CL-1FCL-1FH input ) Do not connect the load exceeding the output rating specified for each model. Since the switching parts and interface elements may be damaged due to the flow of current in excess of the rating caused by noise or surge induction, place the switch at an adequate distance from any power lines or other sources of noise. 2) As a rule of thumb, connect one switch to one unit. 3) Select the installation location of I/F unit so that the cable length between the switch and the I/F unit should not exceed 20m. Main circuit Main circuit In-phase Inverted In-phase Inverted Precautions for DC circuit 27.4 AC/DC power supply No terminal block is provided. Refer to the following. Panasonic: HC2-SFD-S Omron: PYF-08A Connection diagram (Plural switches) When connecting plural switches to one plug-in type interface unit, refer to the diagram below. (1)-(5),or (4)-(8) I/F unit White Output Red I/F unit I/F unit Within 20m 4) Since the I/F unit is not water-proof, protect it from moisture such as water and oil. 5) In case of using Normally-open type switch with a LED indicator, I/F unit can be used only when the LED is normally OFF and turns ON in operation. Similaly, for Normally-Close type switch, the unit can be used only when the LED is normally ON and turns OFF in operation. 6) This I/F unit is especially designed for the METROL switches, do not use this I/F unit with the switch from other manufacturers. Within 100mm It is available only for the switches without LED. I/F unit Output Make sure no noise and inductive source. Overall length of the sensor side cables should be in 100mm. 2-2

7 Common warnings and precautions Electrical Use under the specified contact rating. Chattering may occur when opening and closing the circuit with dry contacts regardless of whether the switch has a snap action mechanism. Take the first signal as a judgment signal. In adverse condition such as using a magnet coil for inductive load and over current may occur, regardless of whether the switch has dry contacts or is contact-less using interface unit with built-in surge protection unit is recommended(refer to P2-2). When using the switch with LED, keep the current below 10mA. How to use When using the plunger type with plain bearing, make contact with the detected object at right angle (with deflection angle ±3 ). For sliding, rotating, angled, offset objects, use ball bearing type or contacting ball type. Installation Ensure that the threaded part of the switch is not bent during installation. When using fixing screws, do not tighten the screws with excessive force. That may distort the switch shape or restrict the movement of the plunger. If the fixing screws are damaged, the switch can be stuck and difficult to be detached. When the switch with a protective cover is installed horizontally, an extra cover is needed separately to prevent coolant or cuttings from entering inside and getting piled up on the switch. Metal cutting For the switches without stopper Do not excessively press the plunger to the stroke end. It may cause malfunction due to impact. If there is possibility to press the plunger to the stroke end, install a separate stopper to prevent malfunction. Slipping after push-in When the plunger is pushed straight by the detected object, do not allow the object to abruptly slide away, as it will cause the plunger to snap back. Note that this may cause failure of the bearing and built-in switching part. Because offset distance (misalignment with axis of the plunger) should be shorter than 5mm, the maximum diameter for detecting surface is 10mm for the plunger type with plain bearing. In case the detected surface is angled or ragged, note that the switch may fail to operate properly or cause malfunction. If the contacting part is worn away depending on conditions, the signal point becomes different. When designing the detected objects, give consideration to its angle, chamfer and roughness so that the contacting part holds up longer. (Mainly for sliding touch type) Work piece Stopper surface Within stroke Work piece Within stroke Stopper For cartridge type switches Tighten the cartridge firmly by fingers. Do not use pliers to fix it. That may cause malfunction. The cartridge is thin. Handle it carefully. When installing the cartridge type switches, give consideration to enough space to replace the cartridge. Screw / nut tightening torque Screw / Nut Operating environment Screw / Nut Tightening torque Applicable models Use in the environment in where cuttings and dust don't prevent switch movement. Choose protective cover option in case cutting may damage the rubber boot. An extra cover is recommended to avoid direct hit by high-pressure coolant or heavy cuttings. PT-Touch MT-Touch CS-Touch M5 M8 M10 M14 M5 m 4Nm 8Nm 10Nm 2Nm PT P085DB P10 P10DH CSJ055 Contacting part material Even though hardened stainless steel is used as the material of the contacting part or stopper surface (for Stopper Bolt with a Built-in series), they are oxidized and may gather rust under certain conditions. Rubber for protective structure (boot, seal, O-ring) Rubbers for some products are intended for water-soluble cutting oil (Alkaline). For oily, chlorine-base, coolants and other chemicals, consult METROL for assistance. The rubber material for High-accuracy MT-Touch and CS-Touch is for both oily and water-soluble coolants. Machine Components with a Built-in Stopper-Mini M60.75 M80.75 M10 M211 M6 M61 M81.25 M101.5 M Nm 7Nm 8Nm 12Nm 2Nm 8Nm 20Nm 35Nm 10Nm CS067 CSP087 CSM CSH ST BP SP STM 2-3

8 Cables and cable protection Type of cable Cabtyre cable Cabtyre cables are used as robot cables without any safety compromise since the working voltage and current are low,though cabtyre cables are not applicable to UL, CSA, EN or other safety standards. Handling instruction 1) Do not pull or twist the cable with excessive force. Max.30N (3kgf) 2) Water-resistance P6-7 Specification Conductor material Conductor resistance Sheath material Minimum bending radius Outer diameter Sheath color Copper-tin alloy, tight winding 1Ω/m (per 1 core) PVC (Non-migrating styrene, oil-resistant, alkaline-resistant) 7mm 3 (2-core) 3.5 (3-core) 4 (2-core for dry contact type, 3-core for contact-less type and 5-core for dry contact type) 5 (s-core, 3-core) 5.5 (5-core) Black : 2 cores, 3 cores for normally close Gray : 2 cores, 3 cores for normally open (Excludes MT-Touch Series) 3) When extending cable length, use cabtyre cable having a cross-section area of at least 0.02mm 2. 4) The minimum bending radius is 7mm. Cable protector (Depending on products) e.g.) CSJ055A Core-wire cable Cable protector For CS-Touch CSM short type (P4-7) and stopper-mini type (P5-16) Specification: 0.6 (0.05mm 2 ) Tensile strength 15N Cross-section area / weight(including sheath / 1m) core AWG 26 (0.151mm 2 ) 10g core AWG 28 (0.096mm 2 ) 15g 4 2-core 16g 4 3-core AWG 28 (0.096mm 2 ) 19g 4 5-core AWG 28 (0.096mm 2 ) 21g 5 2-core 26g 5 4-core 32g 5 3-core 26g core 33g Outer dimension L : Tubular type Cable 3 or smaller Cable 4 Cable LED lamp 9.3 LED lamp 9.3 LED lamp 120 (25) 120 (17) 120 (17) 2-4