ROTARY MOTORIZED VALVES

Transcription

1 ROTRY MOTORIZED VLVES

2 ESE ROTRY VLVES regulate the heating comfort of millions of households. When we decided to develop the next generation of valves and actuators, we started by asking installation engineers, OEM partners and wholesalers which product improvements they wanted to see. The result? completely new standard. The new generation of rotary valves and actuators will make your job easier. They save energy and provide improved levels of comfort. Not to mention all the benefits resulting from the innovations and new application opportunities. There are many new features, but also much that you will already be familiar with. wide range of rotary valves in a number of different designs for the regulation of heating and cooling. dd to that many different actuators for simple and quick installation on the valve. Giving you a complete motorized valve that guarantees reliable, energy-efficient operation for many years to come.

3 TLE OF CONTENTS ROTRY MOTORIZED VLVES SELECT SUITLE MIXING VLVE ND CTUTOR SERIES VRG130 SERIES VRG140 CHNGE-OVER VLVE SERIES VRG SERIES VR140 SERIES 3MG, 4MG, 5MG SERIES 3F, 4F SERIES T,TM SERIES 3H, 4H, 3HG, 4HG CTUTOR SERIES R600 CTUTOR SERIES

4 ESE GUIDE SELECT THE SUITLE ESE 3-way or 4-way mixing valves, sizes DN , for heating and cooling systems in buildings. ESE 3-way mixing valves are usually connected as a mixing valve, but it may also be used as a change-over valve or diverting valve. ESE 4-way mixing valves are used when a higher return water temperature to the boiler is required. FIELDS OF PPLICTION 1) Control of (fluid) water based systems for heating and cooling: radiator heating, floor heating and other surface heating and cooling systems. ) Change-over or diverting valve (only 3-way valves). Make sure that the nominal pressure, the differential pressure as well as the leak rate are within acceptable values. This information is stated for each valve. HOW TO SELECT ROTRY If high return temperature is required (mostly solid fuel installations) a 4-way mixing valve is recommended. In all other applications/installations a 3-way valve is preferred. In systems with two heat sources or storage tanks, the VR-valve helps to prioritize the cheapest energy source and keeps a good temperature stratification in the storage tank. OPERTION 3-WY VLVES The required system temperature is obtained by adding a suitable proportion of return water to the boiler flow. OPERTION 4-WY VLVES The valves have a double mixing function, i.e. a proportion of the hot water supplied from the boiler is mixed with the return water. This results in a higher return water temperature, reducing the risk of corrosion and assuring a longer life for the boiler. SELECTION OF SIZE Each size of mixing valve has a Kvs-value (capacity in m 3 /h at a pressure drop of 1 bar) stated. It is the Kvs-value as well as the system the valve serves that decides which valve to choose. You find suitable Kvs-values in the graphs to the right. For a radiator system Δt = 0 C is usually chosen and for under floor heating Δt = 5 C. Suitable pressure drop should be in the range 3 15 kpa. s a rule of thumb, the lowest Kvs-value is chosen, if there are two alternatives within the pressure drop range. MTERIL/MEDI Valve series VRG, VR and 5MG are made of a special brass alloy (DZR) and therefore also suitable for domestic water installations. ESE s other series of mixing valves may only be used in closed systems where the water is not oxygenated. maximum of 50% glycol for freezing protection and oxygen absorbing compounds are allowed as additives. s both the viscosity and the thermal conduction are affected when glycol is added to the system water, this fact has to be considered when dimensioning the valve. good rule is to choose one size higher Kv-value when % glycol is added. lower concentration of glycol does not affect the valve performance. OPERTION 5-WY VLVES Mixing valve with 4 inlets for use in systems with three heat sources or three layers in a storage tank. OPERTION IVLENT VLVES Mixing valve with 3 inlets for use in systems with two heat sources or two layer storage tank. VLVES, RE. PED 97/3/EEC Pressure Equipment in conformity with PED 97/3/EC, article 3.3 (sound engineering practice). ccording to the directive the equipment shall not carry any CE-mark. DISPOSL OF VLVES The products must not be disposed of together with domestic waste, but should be treated as metal scrap. Local and currently valid legislation must be observed. DISPOSL OF CTUTORS ND REGULTORS The device must not be disposed of together with domestic waste. This applies in particular to the printed circuit card. Legislation may demand special handling of certain components, or it may be desirable from an ecological point of view. Local and currently valid legislation must be observed. 34

5 ESE GUIDE SELECT THE VLVE SIZE, SERIES VRG ND VR HETING SYSTEMS (RDITOR OR UNDERFLOOR HETING SYSTEMS) Start with the heat demand in kw (e.g. 5 kw) and move vertically to the chosen Δt (e.g. 15 C). Move horizontally to the shaded field (pressure drop of 3-15 kpa) and select the smaller Kvs-value (e.g. 4.0). mixing valve with suitable Kvs-value will be found in respective product description. OTHER PPLICTIONS Make sure maximum ΔP is not exceeded (see lines and in the graph below). ROTRY MOTORIZED VLVES Flow m 3 /h l/s Δt = 5 C 10 C 7.5 C 15 C 0 C 30 C 40 C Kvs [m 3 /h] 40 DN50 5 DN40 16 DN3 10 DN5 6.3 DN0 4.0 DN15.5 DN DN DN DN DN Power [kw] Pressure drop ΔP [kpa] max ΔP max ΔP Mixing Diverting 100 kpa = 1 bar 10 mwc 35

6 ESE GUIDE SELECT THE VLVE SIZE, SERIES MG, F, T/TM ND H/HG HETING SYSTEMS (RDITOR OR UNDERFLOOR HETING SYSTEMS) Start with the heat demand in kw (ex. 5 kw) and move vertically to the chosen Δt (ex. 15 C). Move horizontally to the shaded field (pressure drop of 3-15 kpa) and select the smaller Kvs-value (ex. 4.0). Mixing valve with suitable Kvs-value will be found in respective product description. OTHER PPLICTIONS Make sure maximum ΔP is not exceeded. Flow m 3 /h l/s Δt = 5 C 7.5 C 10 C 15 C 0 C 30 C 40 C Kvs = Power kw Pressure drop ΔP [kpa] 36

7 ESE GUIDE FLOW CHRT FOR REGULTING/S Flow m 3 /h l/s C Kvs m 3 /h The Kvs-value applies to flow in one direction only. For 4-way valves the actual ΔP is twice the value shown in chart. Kvs m 3 /h F DN Series MG DN ROTRY MOTORIZED VLVES max ΔP Series F, DN Pressure drop ΔP [kpa] C max ΔP Series F, DN 0 50 max ΔP Series MG, DN kpa = 1 bar 10 mvp 37

8 SERIES VRG130 The compact rotary 3-way mixing valve series VRG130 is available in DN 15 50, and is made of DZR brass, PN10. Three types of connections are available; internal thread, external thread and compression fittings. OPERTION The ESE series VRG130 is a range of compact low leakage mixing valves made of a special brass alloy (DZR) allowing use in both heating, cooling and tap water installations. For easy manual operation the valves are equipped with non-slip knobs and end stops for an operation angle of 90. The valve position scale can be turned over and rotated, allowing a wide choice of mounting positions. Together with actuator series ESE R600 the VRG130 valves are also easily automated and have extraordinary regulating accuracy thanks to the unique valve-to-actuator interface. For more advanced control functions, the ESE series 90 controllers allows even more applications. ESE VRG130 valves are available in dimensions DN with internal thread, in DN with external thread and with compression fittings for pipe O.D. and 8 mm. SERVICE ND MINTENNCE The slender and compact design of the valve allows for easy tool access when assembling and disassembling the valve. Repair kits are available for key components. n extra O-ring can also be installed as additional shaft seal without any need for draining the system or dismantling the valve, as long as the system is depressurized. INSTLLTION EXMPLES ll the examples of installations can be mirrored. The valve position scale can be turned over and rotated to fit a number of installation layouts and should at the installation be fitted in the correct position as shown in the instruction for installation. The symbol markings of the valve ports ( ) minimize the risk of incorrect installation. VLVE VRG130 DESIGNED FOR Heating Comfort cooling Potable water Floor heating Solar heating SUITLE CTUTORS The valve series VRG130 may most easily be fitted with ESE actuators: Series R600 Series 90* Ventilation Zone District hot water District heating District cooling Series 90C Series 90K *daptor kit necessary, see product page TECHNICL DT Pressure class: PN 10 Media temperature: max. (continuously) +110ºC max. (temporarily) +130ºC min. -10ºC Torque (at nominal pressure): < 5 Nm Leakrate in % of flow*: Mixing < 0.05% Diverting < 0.0% Working pressure: 1 MPa (10 bar) Max. differential pressure drop: Mixing, 100 kpa (1 bar) Diverting, 00 kpa ( bar) Close off pressure: 00 kpa ( bar) Rangeability Kv/Kv min, -: 100 Connections: Internal thread, ISO 7/1 External thread, ISO 8/1 * Differential pressure 100kPa (1 bar) Material Valve body and slide: rass DZR, CW 60N Shaft and bushing: PPS composite O-rings: EPDM PED 97/3/EC, article 3.3 VLVE CHRCTERISTICS Flow [%] Opening angle [ ] Mixing Diverting 38

9 SERIES VRG130 NEW D 3-WY SERIES VRG131, INTERNL THRED C Mixing Diverting The flat-sided spindle top points towards the sleeve position. rt. No. Reference DN Kvs* Connection C D Replaces VRG Rp 1/ VRG Rp 1/ MG VRG Rp 1/ MG VRG Rp 1/ MG VRG Rp 1/ MG VRG Rp 1/ VRG Rp 3/ VRG Rp 3/ MG VRG Rp 3/ MG VRG Rp MG VRG Rp MG VRG Rp 1 1/ MG VRG Rp 1 1/ G VRG Rp G Note ROTRY MOTORIZED VLVES 3-WY SERIES VRG13, EXTERNL THRED rt. No. Reference DN Kvs* Connection C D Replaces VRG G 3/4" VRG G 3/4" VRG G 3/4" VRG G 3/4" VRG G 3/4" VRG G 3/4" VRG G 1" VRG G 1" VRG G 1" MG VRG G 1 1/4" VRG G 1 1/4" MG VRG G 1 1/" MG VRG G " VRG G 1/4" Note 3-WY SERIES VRG133, COMPRESSION FITTING rt. No. Reference DN Kvs* Connection C D Replaces VRG CPF mm VRG CPF mm MG VRG CPF 8 mm MG 8-8 * Kvs-value in m 3 /h at a pressure drop of 1 bar. See also flow chart on page 35. CPF = compression fitting Note 39

10 SERIES VRG140 The compact rotary 4-way mixing valve series VRG140 is available in DN 15 50, and is made of DZR brass, PN10. Two types of connections are available; internal thread and external thread. OPERTION The ESE series VRG140 is a range of compact low leakage mixing valves made of a special brass alloy (DZR) allowing use in heating, cooling and tap water installations. For easy manual operation the valves are equipped with non-slip knobs and end stops for an operation angle of 90. The valve position scale can be turned over and rotated, allowing many different mounting positions. Together with actuator series ESE R600, the VRG140 valves are also easily automated and have good regulating accuracy thanks to the unique valve-to-actuator interface. For more advanced control functions, the ESE series 90 controllers allow even more applications. ESE VRG140 valves are available in dimensions DN with internal thread and in dimensions DN15-50 with external thread. SERVICE ND MINTENNCE The slender and compact design of the valve allows for easy tool access when assembling and disassembling the valve. Repair kits are available for key components. n extra O-ring can also be installed as additional shaft seal without any need for draining the system or dismantling the valve, as long as the system is depressurized. INSTLLTION EXMPLES ll the examples of installation can be mirrored. The valve position scale can be turned over and rotated to fit a number of installation layouts and should at the installation be fitted in the correct position as shown in the instruction for installation. The symbol markings of the valve ports ( ) minimize the risk of incorrect installation. VLVE VRG140 DESIGNED FOR Heating Comfort cooling Potable water Floor heating Solar heating SUITLE CTUTORS The valve series VRG140 may most easily be fitted with ESE actuators: Series R600 Series 90* Ventilation Zone District hot water District heating District cooling TECHNICL DT Pressure class: PN 10 Media temperature: max. (continuously) +110ºC max. (temporarily) +130ºC min. -10ºC Torque (at nominal pressure): < 5 Nm Leakrate in % of flow*: < 1.0% Working pressure: 1 MPa (10 bar) Max. differential pressure drop: 100 kpa (1 bar) Close off pressure: 100 kpa (1 bar) Rangeability Kv/Kv min, -: 100 Connections: Internal thread, ISO 7/1 External thread, ISO 8/1 * Differential pressure 100kPa (1 bar) Material Valve body and slide: rass DZR, CW 60N Shaft and bushing: PPS composite O-rings: EPDM PED 97/3/EC, article 3.3 Series 90C Series 90K *daptor kit necessary, see product page VLVE CHRCTERISTICS Flow [%] Opening angle [ ] 40

11 SERIES VRG140 D NEW Riser C From boiler To boiler Return line The flat-sided spindle top points towards the sleeve position. ROTRY MOTORIZED VLVES 4-WY SERIES VRG141, INTERNL THRED rt. No. Reference DN Kvs* Connection C D Replaces VRG Rp 1/ MG VRG Rp 3/ MG VRG Rp 3/ MG VRG Rp MG VRG Rp 1 1/ MG VRG Rp 1 1/ G VRG Rp G Note 4-WY SERIES VRG14, EXTERNL THRED rt. No. Reference DN Kvs* Connection C D Replaces VRG G 3/4" VRG G 1" VRG G 1" MG VRG G 1 1/4" VRG G 1 1/" VRG G " VRG G 1/4" * Kvs-value in m 3 /h at a pressure drop of 1 bar. See also flow chart on page 35, Note 41

12 CHNGE-OVER / DIVERTING VLVE SERIES VRG30 The compact rotary 3-way change-over valve series VRG30 is available in DN 0 50, and is made of DZR brass, PN 10. Three types of connections; internal thread, external thread or with compression fittings. OPERTION The ESE series VRG30 is a range of low leakage rotary valves made of a special brass alloy (DZR) suitable for change-over operation where no regulating characteristics are required. For easy manual operation, the valves are equipped with non-slip knobs and end stops. The valve position scale can be turned over and rotated, allowing a wide choice of mounting positions. Together with actuator series ESE R600 equipped with auxiliary switch the VRG30 valves are also easily automated thanks to the unique valve-to-actuator interface. ESE VRG30 valves are available in dimensions DN 0 50 with internal thread, in DN 0 50 with external thread and with compression fittings for pipe O.D. and 8 mm. SERVICE ND MINTENNCE The slender and compact design of the valve allows for easy tool access when assembling and disassembling the valve. Repair kits are available for key components. n extra O-ring can also be installed as additional shaft seal without any need for draining the system or dismantling the valve, as long as the system is depressurized. INSTLLTION EXMPLES ll the examples of installations can be mirrored. The valve position scale can be turned over and rotated to fit a number of installation layouts and should at the installation be fitted in the correct position as shown in the instruction for installation. The symbol markings of the valve ports ( ) minimize the risk of incorrect installation. VLVE VRG30 DESIGNED FOR Heating Comfort cooling Potable water Floor heating Solar heating SUITLE CTUTORS The valve series VRG30 may most easily be fitted with ESE actuators: Series R600 Series 90* Ventilation Zone District hot water District heating District cooling Series 90C Series 90K *daptor kit necessary, see product page TECHNICL DT Pressure class: PN 10 Media temperature: max. (continuously) +110ºC max. (temporarily) +130ºC min. -10ºC Torque (at nominal pressure): < 5 Nm Leakrate in % of flow*: Mixing < 0.05% Diverting < 0.0% Working pressure: 1 MPa (10 bar) Max. differential pressure drop: Mixing, 100 kpa (1 bar) Diverting, 00 kpa ( bar) Close off pressure: 00 kpa ( bar) Rangeability Kv/Kv min, -: 100 Connections: Internal thread, ISO 7/1 External thread, ISO 8/1 * Differential pressure 100kPa (1 bar) Material Valve body and slide: rass DZR, CW 60N Shaft and bushing: PPS composite O-rings: EPDM PED 97/3/EC, article 3.3 4

13 CHNGE-OVER / DIVERTING VLVE SERIES VRG30 D NEW 3-WY CHNGE-OVER VLVE SERIES VRG31, INTERNL THRED C rt. No. Reference DN Kvs* Connection C D The flat-sided spindle top points towards the sleeve position. Replaces VRG Rp 3/ VRG Rp VRG Rp 1 1/ VRG Rp 1 1/ VRG Rp Note ROTRY MOTORIZED VLVES 3-WY CHNGE-OVER VLVE SERIES VRG3, EXTERNL THRED rt. No. Reference DN Kvs* Connection C D Replaces VRG G VRG G 1 1/ VRG G 1 1/ VRG G VRG G 1/ Note 3-WY CHNGE-OVER VLVE SERIES VRG33, COMPRESSION FITTING rt. No. Reference DN Kvs* Connection C D Replaces VRG CPF mm VRG CPF mm VRG CPF 8 mm * Kvs-value in m 3 /h at a pressure drop of 1 bar. See also flow chart on page 35, CPF = compression fitting Note 43

14 SERIES VR140 The compact rotary mixing valve series VR140 for bivalent heating systems is available in DN 15 50, and is made of DZR brass. Three types of connections are available; internal thread, external thread and compression fittings. PN 10. OPERTION ESE series VR140 is a range of compact rotary mixing valve developed for bivalent systems, i.e. where two heat sources are connected in series or parallel. With an actuator and a control device, the ESE VR140 can be used to prioritize between heat sources. For easy manual operation the valves are equipped with non-slip knobs and end stops for an operation angle of 90. The valve position scale can be turned over and rotated, allowing a wide choice of mounting positions. Together with actuator series ESE R600, the VR140 valves are also easily automated and have extraordinary regulating accuracy thanks to the unique valve-to-actuator interface. For more advanced control functions, the ESE series 90 controllers allows even more applications. ESE VR140 valves are available in dimensions DN with internal thread, in DN with external thread and with compression fittings for pipe O.D. and 8 mm. FUNCTION The IV valve has two inlets to which the heat sources can be connected either in parallel or in series. The primary, i.e. the low grade heat source should be connected to port 1 and the secondary to port. When no heat is needed, both ports 1 and are closed. When heat is needed, the supply from port 1 is used as long as the required temperature can be maintained. When this is no longer the case the valve provides initially a mixed flow from ports 1 and. Finally port is fully open and port 1 closed. (The function is like a 3-way valve but with two inlets instead of one.) The IV valve may also be used on water storage tanks where two outlets from the tank are required. One outlet at the top of the tank and one half way down the tank serve the valve and the return line from the heating system is connected to the bottom of the tank. With this arrangement the hot water from the top of the tank will be used in conjunction with the cooler water drawn from the mid position. SERVICE ND MINTENNCE The slender and compact design of the valve allows for easy tool access when assembling and disassembling the valve. Repair kits are available for key components. n extra O-ring can also be installed as additional shaft seal without any need for draining the system or dismantling the valve, as long as the system is depressurized. VLVE VR140 DESIGNED FOR Heating Comfort cooling Potable water Floor heating Solar heating SUITLE CTUTORS The valve series VR140 may most easily be fitted with ESE actuators: Series R600 Series 90* TECHNICL DT Pressure class: PN 10 Media temperature: max. (continuously) +110ºC max. (temporarily) +130ºC min. -10ºC Torque (at nominal pressure): < 5 Nm Leakrate in % of flow*: < 0.5% Working pressure: 1 MPa (10 bar) Max. differential pressure drop: Mixing, 100 kpa (1 bar) Diverting, 00 kpa ( bar) Close off pressure: 00 kpa Rangeability Kv/Kv min, -: 100 Connections: Internal thread, ISO 7/1 External thread, ISO 8/1 * Differential pressure 100kPa (1 bar) Material Valve body and slide: rass DZR, CW 60N Shaft and bushing: PPS composite O-rings: EPDM PED 97/3/EC, article 3.3 VLVE CHRCTERISTICS Flow [%] Ventilation Zone District hot water District heating District cooling Series 90C Series 90K *daptor kit necessary, see product page Opening angle [ ] R R R

15 SERIES VR140 NEW INSTLLTION EXMPLES ll the examples of installation can be mirrored. The valve position scale can be turned over and rotated to fit a number of installation layouts and shall at the installation be fitted in the correct position as shown in the instruction for installation. The symbol markings of the valve ports ( ) minimize the risk of incorrect installation. ROTRY MOTORIZED VLVES Storage tank mixing Storage tank loading Parallel heat sources Serial heat sources 45

16 SERIES VR140 D Riser Heat source Return line C Heat source 1 The flat-sided spindle top points towards the sleeve input. 4-WY SERIES VR141, INTERNL THRED rt. No. Reference DN Kvs* Connection C D Replaces VR Rp 1/ VR Rp 3/ VR Rp 3/ VR Rp IV 5 Rp VR Rp 1 1/ VR Rp 1 1/ VR Rp Note 4-WY SERIES VR14, EXTERNL THRED rt. No. Reference DN Kvs* Connection C D Replaces VR G 3/4" VR G 1" IV 0 G 3/ VR G 1" VR G 1 1/4" VR G 1 1/" VR G " VR G 1/4" Note 4-WY SERIES VRG143, COMPRESSION FITTING rt. No. Reference DN Kvs* Connection C D Replaces Note VR CPF mm IV 0 CPF mm VR CPF mm VR ,3 CPF 8 mm * Kvs-value in m 3 /h at a pressure drop of 1 bar. See also flow chart on page 35. CPF = compression fitting 46

17 DESIGNTION CODE SYSTEM FOR NEW PRODUCTS Type designations consists of 6 characters in a combination of 3 letters and 3 digits as illustrated below., C13 NEW [C] Subseries [] Product area L = Linear R = Rotary T = Thermic or Thermostatic Z = Diverting [] Type of product = ctuator L = Load unit V = Valve DESIGNTION CODE SYSTEM FOR ROTRY MOTORIZED VLVES ROTRY VLVES [VR_] Rotary valves are available as series VRG which replaces series G and MG, and series VR which replaces series IV. VRG13 ROTRY CTUTORS [R_] R13 [3] Type of Connection 1 = female = male 3 = compression fitting [] Flow = -way 3 = 3-way 4 = 4-way [1] Version 1 = regulating characteristic = non-regulating characteristic Rotary ctuators are available as series R which replaces series 60. [3] Control signal /Voltage 1 = 3-point, 30 VC = 3-point, 30 VC, uxiliary switch 3 = 3-point, 4 VC 4 = 3-point, 4 VC, uxiliary switch 5 = -point, 30 VC 6 = -point, 30 VC, uxiliary switch 7 = -point, 4 VC 8 = -point, 4 VC, uxiliary switch 9 = Proportional control signal [] Running time 1 = 3 seconds = 7 seconds 3 = 15 seconds 4 = 30 seconds 5 = 60 seconds 6 = 10 seconds 7 = 40 seconds 8 = 480 seconds 9 = variable running time [1] Version 6 = version 1 (replaces series 60) 47

18 SERIES 3MG 3MG, DN 15 3, DZR brass, PN 10. Three types of connections; internal thread, external thread or with compression fittings. OPERTION The ESE series MG is a compact mixing valve made of brass for use in heating and cooling installations. The MG is normally equipped with a knob for manual operation and is also suitable for automatic control. This is a simple operation when using the ESE actuator series R600 or series 90. The scale is graded on both sides and can be turned, allowing a choice of mounting positions. Operation angle = 90. Valves series 3MG are made of a special brass alloy (DZR) and are therefore also suitable for domestic water installations. SERVICE ND MINTENNCE ll major parts are replaceable. The shaft seal consist of two o-rings, one of which can be replaced without the need for draining down the system or dismantling the valve. However, before doing so, the system must be depressurized. INSTLLTION EXMPLES ll the examples of installations can be reversed. The valve position plate is graded on both sides and should at the installation be fitted in the correct position as shown in the instruction for installation. VLVE 3MG DESIGNED FOR Heating Comfort cooling Potable water Floor heating Solar heating SUITLE CTUTORS The valve series 3MG may most easily be fitted with ESE actuators: Series R600 Series 60 Ventilation Zone District hot water District heating District cooling Series 90 Series 90C Series 90K TECHNICL DT Pressure class: PN 10 Media temperature: max C min. 10 C Differential pressure drop: max. 100 kpa Torque: max. 3Nm Leakrate in % of flow: see table Rangeability Kv/Kv min : 100 Connections: Internal thread, ISO 7/1 External thread, ISO 8/1 Material Valve body, spindle and slide: rass DZR, CW 60N ushing: Plastic Cover plate: Zinc O-rings: EPDM VLVE CHRCTERISTICS C D % hot water Valve position 48

19 SERIES 3MG E D Mixing 3-WY SERIES 3MG, EXTERNL THRED rt. No. Reference DN Kvs* Connection C D E C Leakrate in % of flow** mixing diverting MG G WY SERIES 3MGP, PUMP FLNGE ND EXTERNL THRED rt. No. Reference DN Kvs* Connection C D E Diverting The flat-sided spindle top (as well as the indicator of the knob) points towards the sleeve position. Leakrate in % of flow** mixing diverting MGP G1 / G1 1/ / PF 1 1/ MGP G1 / G1 1/ / PF 1 1/ MGP G1 / G1 1/ / PF 1 1/ MGP G1 / G1 1/ / PF 1 1/ ROTRY MOTORIZED VLVES 3-WY SERIES 3MGR, ROTTING NUT rt. No. Reference DN Kvs* Connection C D E Leakrate in % of flow** mixing diverting MGR RN * Kvs-value in m 3 /h at a pressure drop of 1 bar. See also flow chart on page 36. ** Differential pressure 50 kpa CPF = compression fitting, PF = Pump Flange, RN = Rotating Nut 49

20 SERIES 4MG 4MG, brass, DN 15 3, PN 10. Internal or external thread. OPERTION The ESE series MG is a compact mixing valve made of brass for use in heating and cooling installations. The MG is normally equipped with a knob for manual operation and is also suitable for automatic control. This is a simple operation when using the ESE actuator series R600 or series 90. The scale is graded on both sides and can be turned, allowing a choice of mounting positions. Operation angle = 90. SERVICE ND MINTENNCE ll major parts are replaceable. The shaft seal consist of two o-rings, one of which can be replaced without the need for draining down the system or dismantling the valve. However, before doing so, the system must be depressurized. INSTLLTION EXMPLES ll the examples of installations can be reversed. The valve position plate is graded on both sides and should at the installation be fitted in the correct position as shown in the instruction for installation. VLVE 4MG DESIGNED FOR Heating Comfort cooling Potable water Floor heating Solar heating SUITLE CTUTORS The valve series 4MG may most easily be fitted with ESE actuators: Series R600 Series 60 Ventilation Zone District hot water District heating District cooling Series 90 Series 90C Series 90K TECHNICL DT Pressure class: PN 10 Media temperature: max C min. 10 C Differential pressure drop: max. 100 kpa Torque: Max. 3Nm Leakrate in % of flow: see table Rangeability Kv/Kv min : 100 Connections: Internal thread, ISO 7/1 External thread, ISO 8/1 Material Valve body, spindle and slide: rass CW 614N ushing: Plastic Cover plate: Zinc O-rings: EPDM VLVE CHRCTERISTICS % hot water Valve position 50

21 SERIES 4MG E D Riser C From boiler To boiler Return line The flat-sided spindle top (as well as the indicator of the knob) points towards the sleeve position. ROTRY MOTORIZED VLVES 4-WY SERIES 4MGP, PUMP FLNGE ND EXTERNL THRED rt. No. Reference DN Kvs* Connection C D E Leakrate in % of flow** MGP Rp 1 / PF 1 1/ WY SERIES 4MGR, ROTTING NUT ND EXTERNL THRED rt. No. Reference DN Kvs* Connection C D E Leakrate in % of flow** MGR G 1 / RN * Kvs-value in m 3 /h at a pressure drop of 1 bar. See also flow chart on page 36. ** Differential pressure 50 kpa. PF = Pump Flange, RN = Rotating Nut 51

22 SERIES 5MG 5MG, DN 5 3, brass, PN 10. Internal thread connection. OPERTION The ESE series 5MG is a compact mixing valve with five ports. It is made of brass for use in heating installations. Series 5MG is normally equipped with a knob for manual operation and is also suitable for automatic control. This is a simple operation when using the ESE actuator 9P4 (article number ). Series 5MG is available in dimensions DN 5 3 with internal thread. The scale is graded on both sides and can be turned, allowing a choice of mounting positions. Operation angle = 70. FUNCTION When used as mixing valve it has four inlets to be connected so that they draw heat from different layers in a storage tank or from different heat sources. When used as a diverting valve it has four outlets to be connected so that they feed different layers in a storage tank. SERVICE ND MINTENNCE ll major parts are replaceable. The shaft seal consist of two o-rings, one of which can be replaced without the need for draining down the system or dismantling the valve. However, before doing so, the system must be depressurized. INSTLLTION EXMPLES ll the examples of installations can be reversed. The valve position plate is graded on both sides and should at the installation be fitted in the correct position as shown in the instruction for installation. VLVE 5MG DESIGNED FOR Heating Comfort cooling Potable water Floor heating Solar heating SUITLE CTUTORS The valve series 5MG may most easily be fitted with ESE actuators: Series 90, type 9P4 Ventilation Zone District hot water District heating District cooling TECHNICL DT Pressure class: PN 10 Media temperature: max C min. 10 C Differential pressure drop: max. 100 kpa Torque: max. 3Nm Leakrate in % of flow: see table Rangeability Kv/Kv min : 100 Connections: Internal thread, ISO 7/1 Material Valve body, spindle and slide: rass CW 614N ushing: Plastic Cover plate: Zinc O-rings: EPDM Mixing Diverting 5

23 SERIES 5MG 0 NEW D E C 3 5 The flat-sided spindle top (as well as the indicator of the knob) points towards the opening in the sleeve. 5 ROTRY MOTORIZED VLVES 5-WY SERIES 5MG, INTERNL THRED rt. No. Reference DN Kvs* Connection C D E Leakrate in % of flow** MG Rp MG Rp 1 1/ * Kvs-value in m 3 /h at a pressure drop of 1 bar. See also flow chart on page 36. ** Differential pressure 50 kpa 53

24 SERIES 3F 3F, DN 0 150, cast iron, PN 6. Flange. OPERTION The ESE series F is a valve made of cast iron for use in heating and cooling installations. The mixing proportions are adjusted manually with a handle or, in automatically controlled systems, by means of an actuator. Suitable actuators are ESE series R600 for DN <50 or series 90. Valve series 3F is available in dimensions DN with flanged connections. The scale is graded on both sides and can be turned, allowing a choice of mounting positions. Operation angle = 90. SERVICE ND MINTENNCE ll major parts are replaceable. The shaft seal consist two o-rings, one of which can be replaced without the need for draining down the system or dismantling the valve. However, before doing so, the system must be depressurized. INSTLLTION EXMPLES ll the examples of installations can be reversed. The valve position plate is graded on both sides and should at the installation be fitted in the correct position as shown in the instruction for installation. VLVE 3F DESIGNED FOR Heating Comfort cooling Potable water Floor heating Solar heating SUITLE CTUTORS The valve series 3F may most easily be fitted with ESE actuators: Series R600 < DN50 Series 60 Ventilation Zone District hot water District heating District cooling Series 90 Series 90C Series 90K TECHNICL DT Pressure class: PN 6 Media temperature: max. 110 C, min. 10 C Differential pressure drop: DN 0 50, max. 50 kpa DN , max. 30 kpa Leakrate in % of flow: max. 1.5% Rangeability Kv/Kv min : 100 Connection: Flange according to DIN 531 Material DN 0 5 DN Valve body: Cast iron EN JL 1030 Slide: brass CW 614N brass CW 614N and stainless steel ushing: plastic brass CW 60N Cover plate: zinc cast iron O-rings: EPDM C D REQUIRED CTUTOR TORQUE The figures below are intended only as a recommendation for ordinary installations. In some applications the valve may require even more actuator torque. Valve size up to DN 5 actuator torque 3 Nm DN 50 5 Nm DN Nm DN Nm VLVE CHRCTERISTICS % hot water Valve position 54

25 SERIES 3F F 3 Flanged connection PN6, standard DIN 531 E G C D Mixing Diverting The flat-sided spindle top (as well as the indicator of the knob) points towards the sleeve position. ROTRY MOTORIZED VLVES 3-WY SERIES 3F rt. No. Reference DN Kvs* C D E F G F x F x F x F x F x F x F x F x F x F x * Kvs-value in m 3 /h at a pressure drop of 1 bar. See flow chart on page

26 SERIES 4F 4F, DN 3 150, cast iron, PN 6. Flange. OPERTION The ESE series F is a valve made of cast iron for use in heating and cooling installations. The mixing proportions are adjusted manually with a handle or, in automatically controlled systems, by means of an actuator. Suitable actuators are ESE series R600 for DN <50 or series 90. Valve series 4F is available in dimensions DN with flanged connections. The scale is graded on both sides and can be turned, allowing a choice of mounting positions. Operation angle = 90. SERVICE ND MINTENNCE ll major parts are replaceable. The shaft seal consist two o-rings, one of which can be replaced without the need for draining down the system or dismantling the valve. However, before doing so, the system must be depressurized. INSTLLTION EXMPLES ll the examples of installations can be reversed. The valve position plate is graded on both sides and should at the installation be fitted in the correct position as shown in the instruction for installation. VLVE 4F DESIGNED FOR Heating Comfort cooling Potable water Floor heating Solar heating SUITLE CTUTORS The valve series 4F may most easily be fitted with ESE actuators: Series R600 < DN50 Series 60 Ventilation Zone District hot water District heating District cooling Series 90 Series 90C Series 90K TECHNICL DT Pressure class: PN 6 Media temperature: max. 110 C, min. 10 C Differential pressure drop: DN 0 50, max. 50 kpa DN , max. 30 kpa Leakrate in % of flow: max. 1.5% Rangeability Kv/Kv min : 100 Connection: Flange according to DIN 531 Material DN 0 5 DN Valve body: Cast iron EN JL 1030 Slide: brass CW 614N brass CW 614N and stainless steel ushing: plastic brass CW 60N Cover plate: zinc cast iron O-rings: EPDM REQUIRED CTUTOR TORQUE The figures below are intended only as a recommendation for ordinary installations. In some applications the valve may require even more actuator torque. Valve size up to DN 5 actuator torque 3 Nm DN 50 5 Nm DN Nm DN Nm VLVE CHRCTERISTICS % hot water Valve position 56

27 SERIES 4F D Riser Flanged connection PN6, standard DIN 531 E G F C From boiler To boiler Return line The flat-sided spindle top (as well as the indicator of the knob) points towards the sleeve position. ROTRY MOTORIZED VLVES 4-WY SERIES 4F rt. No. Reference DN Kvs* C D E F G F x F x F x F x F x F x F x F x * Kvs-value in m 3 /h at a pressure drop of 1 bar. See flow chart on page

28 SERIES T ND TM ESE 4-way valves Series T and TM are specially designed for factory fitting to boilers. 4T, DN 0 3, cast iron, PN 6. Internal thread. 4 TM, DN 0, brass, PN 10. External thread or with compression fittings. OPERTION The T/TM valves have the two ports for the boiler side in a single flange. The riser and return from the radiator system have internal threaded connections. Suitable flanges for welding to the boiler are also available. The T/TM valves have a double mixing function, i.e. a proportion of the hot water supplied from the boiler is mixed with the return water. This results in a higher return water temperature reducing the risk of corrosion and assuring a longer life for the boiler. They are designed to provide good control characteristics and reliability in operation. For automatic control ESE actuator series R600 or series 90 is recommended. SERVICE ND MINTENNCE ll major parts are replaceable. The shaft seal consist of two o-rings, one of which can be replaced without the need for draining down the system or dismantling the valve. However, before doing so, the system must be depressurized. TYPICL INSTLLTION = riser = return C = riser, boiler D = return to boiler The scale plate is printed on both sides allowing inverted installation. VLVE T/TM DESIGNED FOR Heating Comfort cooling Potable water Floor heating Solar heating SUITLE CTUTORS The valve series T and TM may most easily be fitted with ESE actuators: Series R600 Series 60 Ventilation Zone District hot water District heating District cooling Series 90 Series 90C Series 90K TECHNICL DT Pressure class: Series T, PN 6 Series TM, PN 10 Temperature: max. 110 C min. 10 C Operation angle: 90 Torque: Series T, 5 Nm Series TM, 3 Nm Leakrate in % of flow: max. 1.5% Connections: Internal thread, ISO 7/1 External thread, ISO 8/1 Material ody: Series T Cast iron EN JL 1030 Series TM rass CW 614N Slide/Spindle: rass CW 614N ushing: Plastic Cover plate: Zinc O-rings: EPDM VLVE CHRCTERISTICS % hot water Series T C D Series TM C D Valve position 58

29 SERIES T ND TM 4-way MDE IN SWEDEN voise 4-WY SERIES T, INTERNL THRED G rt. No. Reference DN Kvs* Connection C D E F G T Rp 3/ T Rp T Rp 1 1/ * Kvs-value in m 3 /h at a pressure drop of 1 bar. See flow chart on page 36. C D 94 7 E F ROTRY MOTORIZED VLVES G G G D 30 rt. No rt. No rt. No Flange 4-WY SERIES TM, EXTERNL THRED rt. No. Reference DN Kvs* Connection C D G Note TM G 3/ WY SERIES TM, COMPRESSION FITTING rt. No. Reference DN Kvs* Connection C D G Note TM CPF mm TM CPF mm with leakflow TM CPF mm G 1/ in base connection TM CPF mm G 1/ + O-ring groove in base connection WY SERIES TM, ROTTING NUT rt. No. Reference DN Kvs* Connection C D G Note TM RN * Kvs-value in m 3 /h at a pressure drop of 1 bar. Flow chart, see page 36. CPF = compression fitting RN = Rotating Nut 59

30 SERIES H ND HG ESE mixing valves Series H/HG are designed for installations where space is limited. 3H, DN 5 40, cast iron, PN 10. Internal thread. 4H, DN 0 50, cast iron, PN 10. Internal thread. 3HG/4HG, DN5, cast iron, PN10. Union connections. OPERTION ESE mixing valve series H/HG have connections in an H configuration. The upward connections are for radiator circuits and the downward connections are for boiler connection. The H series valves are equipped with female screw connections and the HG series have union connections. The integrated bypass has an adjustable flow with a maximum 50% total capacity of the valve (especially suitable for floor heating installations). For automatic control ESE actuator series R600 or series 90 is recommended. SERVICE ND MINTENNCE ll major parts are replaceable. The shaft seal consist of two o-rings, one of which can be replaced without the need for draining down the system or dismantling the valve. However, before doing so, the system must be depressurized. VLVE H/HG DESIGNED FOR Heating Comfort cooling Potable water Floor heating Solar heating SUITLE CTUTORS The valve series H and HG may most easily be fitted with ESE actuators: Series R600 Series 60 Ventilation Zone District hot water District heating District cooling Series 90 Series 90C Series 90K TECHNICL DT Pressure class: PN 10 Temperature: max. 110 C min. 10 C Differential pressure drop: max. 50 kpa Torque: 5 Nm Leakrate in % of flow: Series H, max. 1.5% Series HG, max. 1% Connections: Internal thread, ISO 7/1 External thread, ISO 8/1 Material ody: Cast iron EN JL 1030 Slide/Spindle: Series H, DN 0-5 rass CW 614N Series H, DN 3-50 rass CW 614N & Stainless steel Series HG rass CW 614N ushing: Series H, DN 0-5 Plastic Series H, DN 3-50 rass CW 60N Series HG Plastic Cover plate: Series H, DN 0-5 Zinc Series H, DN 3-50 Cast iron EN JL 1030 Series HG Zinc O-rings: EPDM 60

31 SERIES H ND HG D 4 3-WY SERIES 3H, INTERNL THRED rt. No. Reference DN Kvs* Connection C D Note C ROTRY MOTORIZED VLVES H5 5 1 Rp H3 3 Rp 1 1/ H Rp 1 1/ WY SERIES 4H, INTERNL THRED rt. No. Reference DN Kvs* Connection C D Note H Rp 3/ H5 5 1 Rp H3 3 Rp 1 1/ H Rp 1 1/ H Rp WY SERIES 3HG, EXTERNL THRED rt. No. Reference DN Kvs* Connection C D Note HG G 1 1/ ) HG G 1 1/ ), ). 4-WY SERIES 4HG, EXTERNL THRED rt. No. Reference DN Kvs* Connection C D Note HG G 1 1/ ) HG G 1 1/ ) HG G 1 1/ ) HG G 1 1/ ), ). *Kvs-value in m 3 /h at a pressure drop of 1 bar. Flow chart, see page 36. Note 1) Male thread for union connections ) With y-pass 61

32 CTUTOR SERIES R600 3-POINT ESE ctuator Series R600 for operating ESE mixing valves DN The actuators have an operating range of 90 and can easily be manually operated. OPERTION The ESE series R600 is a compact actuator designed for operating rotary mixing valves DN The actuators R6X1, R6X, R6X3 and R6X4 are controlled by 3-point signal, and are recommended for mixing applications. The actuator has an operating range of 90 and the valve can easily be manually operated by the pull-andturn knob on the front of the actuator. VERSIONS The ESE actuators with 3-point signal control are available for 4 or 30 VC, 50 Hz and it is supplied with an attached 1.5 m connection cable. wide range of different running times is also available, from 30 to 100 seconds. n auxiliary switch, which can be set in any position, is available either as a pre-mounted component fitted to the actuator (R6X and R6X4) or as an optional kit to be ordered separately. The auxiliary switch is easily set by a unique solution, by just lifting off the turning knob the switch cam is accessible, no tools or disassembly required. SUITLE S Thanks to the special interface between the actuator series R600 and the ESE valve series VRG100, VRG00 and VR100, the unit as a whole has a unique stability and precision when regulating. The actuator series R600 is also easily mounted on the ESE valve series MG, G, F, IV, H and HG. Series VRG100 Series VRG00 Series VR100 Series MG Series G Series F DN50 Series IV Series H and HG LINKGE KITS The actuator is supplied complete with an adaptor kit for easily fitting onto an ESE rotary mixing valve. OPTION uxiliary switch kit rt. No TECHNICL DT mbient temperature: max. +55ºC min. -5ºC Enclosure rating: IP41 Protection class: II Power consumption: 4V V 30V 5 V : 0.4 kg LVD 006/95/EC EMC/86/336/EEC RoHS 00/95/EC WIRING The actuator should be preceded by a multi-pole contact breaker in the fixed installation. M ctuator, series: R641 R644, R651 R654, R661 R664, R671 R674 ctuator, series: R64, R644, R65, R654, R66, R664, R67, R674, R69, R694 The actuators are fitted with two separate cables, one cable for actuator regulation and one for the auxiliary switch. To set the switch position, remove the actuator knob and turn the green cam sleeve to the desired position. 6

33 CTUTOR SERIES R600 3-POINT NEW C + 77 (C = see valve) CTUTOR SERIES R600, 3-POINT 4VC rt. No. Reference Voltage Running time 90 [s] Control signal* Installation dimensions for ctuator Series R600 with ESE VRG100, VRG00 and VR100 mixing valves Torque [Nm] Replaces R643 4 VC, 50Hz 30 3-point SPDT R653 4 VC, 50Hz 60 3-point SPDT R663 4 VC, 50Hz 10 3-point SPDT R673 4 VC, 50Hz 40 3-point SPDT R693 4 VC, 50Hz 10/40/480/100 3-point SPDT R644 4 VC, 50Hz 30 3-point SPDT 6 1) R654 4 VC, 50Hz 60 3-point SPDT 6 1) R664 4 VC, 50Hz 10 3-point SPDT 6 6M 1) R674 4 VC, 50Hz 40 3-point SPDT 6 63M 1) R694 4 VC, 50Hz 10/40/480/100 3-point SPDT 6 1) Note ROTRY MOTORIZED VLVES CTUTOR SERIES R600, 3-POINT 30VC rt. No. Reference Voltage Running time 90 [s] Control signal* Torque [Nm] Replaces R VC, 50Hz 30 3-point SPDT R VC, 50Hz 60 3-point SPDT R VC, 50Hz 10 3-point SPDT R VC, 50Hz 40 3-point SPDT R VC, 50Hz 10/40/480/100 3-point SPDT R64 30 VC, 50Hz 30 3-point SPDT 6 1) R65 30 VC, 50Hz 60 3-point SPDT 6 65M 1) R66 30 VC, 50Hz 10 3-point SPDT 6 66M 1) R67 30 VC, 50Hz 40 3-point SPDT 6 67M 1) R69 30 VC, 50Hz 10/40/480/100 3-point SPDT M 1) * 3-point SPDT = Single Pole Double Throw Note 1) With premounted auxiliary switch Note 63

34 CTUTOR SERIES R600 -POINT ESE ctuator Series R600 for operating ESE mixing valves DN The actuators have an operating range of 90 and can easily be manually operated. OPERTION The ESE series R600 is a compact actuator designed for operating rotary mixing valves DN The actuators R6X5, R6X6, R6X7 and R6X8 are controlled by -point (on/off) signal, and are recommended for diverting applications. The actuator has an operating range of 90 and the valve can easily be manually operated by the pull-andturn knob on the front of the actuator. In addition to the -point signal control, all the actuators can also be used for 3-point signal control. VERSIONS The ESE actuators with -point signal control are available for 4 or 30 VC, 50 Hz and are supplied with a builtin relay and a 1.5 m connection cable attached. Different running times are available, from 15 to 60 seconds. n auxiliary switch, which can be set in any position, is available either as a pre-installed component fitted to the actuator (R6X6 and R6X8) or as an optional kit to be ordered separately. The auxiliary switch is easily set by a unique solution, by just lifting off the turning knob the switch cam is accessible, no tools or disassembly required. SUITLE S Thanks to the special interface between the actuator series R600 and the ESE valve series VRG100, VRG00 and VR100, the unit as a whole has a unique stability and precision when regulating. The actuator series R600 is also easily mounted on the ESE valve series MG, G, F, IV, H and HG. Series VRG100 Series VRG00 Series VR100 Series MG Series G Series F DN50 Series IV Series H and HG LINKGE KITS The actuator is supplied complete with an adaptor kit for easily fitting onto an ESE rotary mixing valve. OPTION uxiliary switch kit rt. No TECHNICL DT mbient temperature: max. +55ºC min. -5ºC Enclosure rating: IP41 Protection class: II Power consumption: 4V V 30V 5 V : 0.4 kg LVD 006/95/EC EMC/86/336/EEC RoHS 00/95/EC WIRING The actuator should be preceded by a multi-pole contact breaker in the fixed installation. -point control signal *The direction of rotation is eligible by jumper setting. M 3-point control signal uxiliary switch M ctuator, series: R635 R638, R645 R648, R655 R658 ctuator, series: R636, R638, R646, R648, R656, R658 The actuators are fitted with two separate cables, one cable for actuator regulation and one for the auxiliary switch. To set the switch position, remove the actuator knob and turn the green cam sleeve to the desired position. 64

35 CTUTOR SERIES R600 -POINT NEW C + 77 (C = see valve) CTUTOR SERIES R600, -POINT 4VC rt. No. Reference Voltage Running time 90 [s] Control signal* Torque [Nm] Installation dimensions for ctuator Series R600 with ESE VRG100, VRG00 and VR100 mixing valves Replaces R637 4 VC, 50Hz 15 -point SPST R647 4 VC, 50Hz 30 -point SPST R657 4 VC, 50Hz 60 -point SPST R638 4 VC, 50Hz 15 -point SPST 3 1) R648 4 VC, 50Hz 30 -point SPST 6 1) R658 4 VC, 50Hz 60 -point SPST 6 1) Note ROTRY MOTORIZED VLVES CTUTOR SERIES R600, -POINT 30VC rt. No. Reference Voltage Running time 90 [s] Control signal* Torque [Nm] Replaces R VC, 50Hz 15 -point SPST R VC, 50Hz 30 -point SPST R VC, 50Hz 60 -point SPST R VC, 50Hz 15 -point SPST 3 1) R VC, 50Hz 30 -point SPST 6 1) R VC, 50Hz 60 -point SPST 6 68M 1) * -point SPST = Single Pole Single Throw Note 1) With premounted auxiliary switch Note 65

36 CTUTOR SERIES R600 PROPORTIONL ESE ctuator Series R600 for operating ESE mixing valves DN The actuators have an operating range of 90 and can easily be manually operated. OPERTION The ESE series R600 is a compact actuator designed for operating rotary mixing valves DN The actuators R6X9 are controlled by proportional signal, and are recommended for mixing applications. The actuator has an operating range of 90 and the valve can easily be manually operated by the pull-and-turn knob on the front of the actuator. In addition to the proportional signal control, actuators series R639 can also be used for 3- and -point signal control. VERSIONS The actuators R6X9 are available for 4 V C/DC, 50/60 Hz power supply. n auxiliary switch, which can be set in any position, is available as an optional kit to be ordered separately. The auxiliary switch is easily set by a unique solution, by just lifting off the turning knob the switch cam is accessible, no tools or disassembly required. The R659 can be set to running times of 45 and 10 seconds and is supplied with a 1.5 m cable attached. The R639 can be set to running times of 15, 30 and 60 seconds and is supplied with a wire socket for connection to a cable of own choice. The R639 also have the additional features of proportional analogue output signal for monitoring devices etc, optional advanced noise reduction of the input signal and positioning memory for fast startup after power failure. SUITLE S Thanks to the special interface between the actuator series R600 and the ESE valve series VRG100, VRG00 and VR100, the unit as a whole has a unique stability and precision when regulating. The actuator series R600 is also easily mounted on the ESE valve series MG, G, F, IV, H and HG. Series VRG100 Series VRG00 Series VR100 Series MG Series G Series F DN50 Series IV Series H and HG LINKGE KITS The actuator is supplied complete with an adaptor kit for easily fitting onto an ESE rotary mixing valve. OPTION uxiliary switch kit rt. No TECHNICL DT mbient temperature: max. +55ºC min. -5ºC Enclosure rating: IP41 Protection class: II Power consumption - Operation: 5 W Power consumption - Dimensioning: R639, 11 V R659, 8 V : 0.4 kg LVD 006/95/EC EMC/86/336/EEC RoHS 00/95/EC WIRING The actuator should be preceded by a multi-pole contact breaker in the fixed installation. 0-10V, -10V, 0-0m, 4-0m L N/ M Y 0-10V/-10V/0-0m/4-0m X -10V ctuator series R659 ctuator series R639 66

37 CTUTOR SERIES R600 PROPORTIONL NEW C + 77 (C = see valve) CTUTOR SERIES R600, PROPORTIONL 4V C/DC rt. No. Reference Voltage Running time 90 [s] R639 4 VC/DC, 50/60Hz 15/30/60/ R659 4 VC/DC, 50/60Hz 45/10 Note 1) Supplied with wire socket connection, no cable included. Control signal* V,..10V, 0..0m, 4..0m V,..10V, 0..0m, 4..0m Installation dimensions for ctuator Series R600 with ESE VRG100, VRG00 and VR100 mixing valves Torque [Nm] Replaces Note 6 1) 6 6P ROTRY MOTORIZED VLVES 67

38 CTUTOR SERIES 90 3-POINT ESE actuator Series 90 for operating ESE mixing valves DN This series is provided with adjustable cam discs to obtain an operating range which make the series very flexible. OPERTION The ESE series 90 actuator is a compact actuator for operating rotary mixing valves. The actuator is reversible and is provided with limit switches which are actuated by cam discs. y adjusting the cam discs an operating range from 30 to 180 can be obtained. The actuator is provided with a disconnection for manual operation and has an indication on the front showing valve position. The 3-point signal control actuator is available for 4 VC, 50/60 Hz, or 30V, 50 Hz with different running times as shown in the table. SUITLE S The actuator is supplied complete with an adaptor kit for easily fitting onto an ESE rotary mixing valve. Series VRG100* Series VRG00* Series VR100* Series MG Series G Series F DN50 Series IV Series H and HG *Separate adaptor kit is required, see below LINKGE KITS Required adaptor kits for easily fitting onto an ESE rotary mixing valve is available in two different styles. daptor kit designed for ESE mixing valve series MG, G, F, IV, H, HG is supplied with each actuator. daptor kits for ESE mixing valve series VRG and VR can be ordered separetely. rt. No (= supplied with actuator) ESE valve series MG, G, F, IV, H, HG ESE valve series VRG, VR 1 To operate the valve manually, push the button and use the lever. The electric current is automatically disconnected as long as the button is in the lower position. Turn the valve to the desired position. daptor kits for other mixing valves and valves built-into boilers are available as follows: rt. No Centra ZR, DR, DRU Centra Kompakt DRK/ZRK CTC, linear movement Sauter MH3 H Siemens VG31, VI31, VF1, VCI T VTR, T STM TC-TRV Viessmann (all nominal diameters) WIT Various adaptor kits for built-in mixing valves 3»CLICK«OPTIONS Separate auxiliary switch, see table next page marked ** rt. No To return to automatic operation, bring the lever to the position where it locks, and the button returns to the upper position. The current supply is now connected. TECHNICL DT mbient temperature: max. +55 C min. 15 C Power consumption: ctuator 4 VC, V ctuator 30 VC, 5 V Enclosure rating: IP 54 Protection class: II Torque: See table : 0.8 kg 68

39 CTUTOR SERIES 90 3-POINT C+114 (C = see valve) CTUTOR SERIES 90, 3-POINT 4 VC rt. No. Reference Voltage [VC] Running time 90 [s] Torque [Nm] Control signal* Installation dimensions for ctuator Series 90 with ESE series MG, G, F, T/TM, H/HG and IV mixing valves Remark point SPDT Separate auxiliary switch as option** point SPDT Separate auxiliary switch as option** point SPDT Separate auxiliary switch as option** point SPDT Separate auxiliary switch as option** M point SPDT With premounted auxiliary switch M point SPDT With premounted auxiliary switch M point SPDT With premounted auxiliary switch M point SPDT With premounted auxiliary switch ROTRY MOTORIZED VLVES CTUTOR SERIES 90, 3-POINT 30 VC rt. No. Reference Voltage [VC] Running time 90 [s] Torque [Nm] Control signal* Remark point SPDT Separate auxiliary switch as option** point SPDT Separate auxiliary switch as option** point SPDT Separate auxiliary switch as option** point SPDT Separate auxiliary switch as option** M point SPDT With premounted auxiliary switch M point SPDT With premounted auxiliary switch M point SPDT With premounted auxiliary switch M point SPDT With premounted auxiliary switch * 3-point SPDT = Single Pole Double Throw WIRING The actuator should be preceded by a multi-pole contact breaker in the fixed installation. uxiliary switch ctuator, rt. No , , , , , , , ctuator with premounted auxiliary switch, rt. No. 105 (04) 00, (09), (11), (15), (18), (1), (), (4) These actuators are supplied with one auxiliary switch. To set the switch position, remove the actuator cover and turn the cam sleeve to the desired position. 69

40 CTUTOR SERIES 90 -POINT ESE actuator Series 90 for operating ESE mixing valves DN This series is provided with adjustable cam discs to obtain an operating range which make the series very flexible. OPERTION The ESE series 90 actuator is a compact actuator for operating rotary mixing valves. The actuator is reversible and is provided with limit switches which are actuated by cam discs. y adjusting the cam discs an operating range from 30 to 180 can be obtained. The actuator is provided with a disconnection for manual operation and has an indication on the front showing valve position. The -point signal control actuator is available for 4 VC, 50/60 Hz, or 30V, 50 Hz with different running times as shown in the table. n -point signal control actuator with built-in relay should be selected when the actuator is to be controlled by an on/off thermostat. SUITLE S The actuator is supplied complete with an adaptor kit for easily fitting onto an ESE rotary mixing valve. Series VRG100* Series VRG00* Series VR100* Series MG Series G Series F DN50 Series IV Series H and HG *Separate adaptor kit is required, see below LINKGE KITS Required adaptor kits for easily fitting onto an ESE rotary mixing valve is available in two different styles. daptor kit designed for ESE mixing valve series MG, G, F, IV, H, HG is supplied with each actuator. daptor kits for ESE mixing valve series VRG and VR can be ordered separetely. rt. No (= supplied with actuator) ESE valve series MG, G, F, IV, H, HG ESE valve series VRG, VR 1 To operate the valve manually, push the button and use the lever. The electric current is automatically disconnected as long as the button is in the lower position. Turn the valve to the desired position. daptor kits for other mixing valves and valves built-into boilers are available as follows: rt. No Centra ZR, DR, DRU Centra Kompakt DRK/ZRK CTC, linear movement Sauter MH3 H Siemens VG31, VI31, VF1, VCI T VTR, T STM TC-TRV Viessmann (all nominal diameters) WIT Various adaptor kits for built-in mixing valves 3»CLICK«To return to automatic operation, bring the lever to the position where it locks, and the button returns to the upper position. The current supply is now connected. TECHNICL DT mbient temperature: max. +55 C min. 15 C Power consumption: 30 VC, 5 V Enclosure rating: IP 54 Protection class: II Torque: See table : 0.8 kg 70

41 CTUTOR SERIES 90 -POINT C+114 (C = see valve) CTUTOR SERIES 90, -POINT 30 VC rt. No. Reference Voltage Running time 90 [s] Torque [Nm] Control signal* point SPST With built-in relay point SPST With built-in relay *-point SPST = Single Pole Single Throw Installation dimensions for ctuator Series 90 with ESE series MG, G, F, T/TM, H/HG and IV mixing valves Remark ROTRY MOTORIZED VLVES WIRING The actuator should be preceded by a multi-pole contact breaker in the fixed installation. ctuator with built-in relay, rt. No , The direction of rotation is changed by a contact located under the cover. 71

42 CTUTOR SERIES 90 PROPORTIONL ESE actuator Series 90 for operating ESE mixing valves DN This series is provided with adjustable cam discs to obtain an operating range which make the series very flexible. OPERTION The ESE series 90 actuator is a compact actuator for operating rotary mixing valves. The actuator is reversible and is provided with limit switches which are actuated by cam discs. For to the operating range is 90 alt. 180, and for the operating range is 355. The actuator is provided with a disconnection for manual operation and has an indication on the front showing valve position. The actuator is also available in step motor driven versions for regulation with different proportional signals and running times. Supply voltage 4V C/DC. The actuators are factory set at 0 10 V and 15 s for , 60 s for resp. 10 s for ny adjustments are made by removal of front cover. SUITLE S The actuator is supplied complete with an adaptor kit for easily fitting onto an ESE rotary mixing valve. Series VRG100* Series VRG00* Series VR100* Series MG Series G Series F DN50 Series IV Series H and HG *Separate adaptor kit is required, see below LINKGE KITS Required adaptor kits for easily fitting onto an ESE rotary mixing valve is available in two different styles. daptor kit designed for ESE mixing valve series MG, G, F, IV, H, HG is supplied with each actuator. daptor kits for ESE mixing valve series VRG and VR can be ordered separetely. rt. No (= supplied with actuator) ESE valve series MG, G, F, IV, H, HG ESE valve series VRG, VR 1 To operate the valve manually, push the button and use the lever. The electric current is automatically disconnected as long as the button is in the lower position. Turn the valve to the desired position. daptor kits for other mixing valves and valves built-into boilers are available as follows: rt. No Centra ZR, DR, DRU Centra Kompakt DRK/ZRK CTC, linear movement Sauter MH3 H Siemens VG31, VI31, VF1, VCI T VTR, T STM TC-TRV Viessmann (all nominal diameters) WIT Various adaptor kits for built-in mixing valves 3»CLICK«To return to automatic operation, bring the lever to the position where it locks, and the button returns to the upper position. The current supply is now connected. TECHNICL DT mbient temperature: max. +55 C min. 15 C Power consumption: 4V C/DC, 5 V Enclosure rating: IP 54 Protection class: II Torque: See table : 0.8 kg 7