Ceramic Heater Bands

Transcription

1 Typical applications are plastic molding and extrusion. Ceramic heater bands are also used for pipe heating, heat treating, and autoclaves or any application where there is a need to apply heat to a cylindrical surface. Ceramic iber Insulation: The standard insulation is 1/4" thick to improve energy conservation 5% and more over non-insulated heater bands. 1/" double-thick insulation is optional. Serrated Sheath: Sheath material is resistant to heat and corrosion. Unique serrations maximize flexibility, increase surface contact and provide easy opening and installation of the heater, eliminating the necessity of two piece heater bands up to 18" in diameter. Simplified Installation, Additional Energy Conservation: Ceramic heater bands can be manufactured in widths much greater than what is practical in mica heater bands, eliminating heat losses between gaps in narrow heater bands and simplifying installation. Ceramic Insulation Chamber Design eatures: Energy efficient, less power consumption. High sheath temperature capability up to 1600 o. Thermally insulated. Uniform temperature. lexible, easy to install and remove. Elongation compensation with spring loaded screw. (over 18" diameter) 450 Phone: Toll ree: ax: Toll ree ax: ORDER TOLL REE

2 ig. S ig. B Screw Terminals and Box Protection: 1/4-0 x 1" threaded terminals are standard as in ig. S or in terminal box as in ig. B. Under " width, terminals are parallel to circumference. Over " width, terminals are perpendicular to the circumference. Standard position is 180 o from gap. ig. L ig. A Braid or Conduit Protection: To protect leads against abrasion, braided sleeve in ig. L is held in place by a clip. Conduit in ig. A is connected to stand off bracket. Standard poition is 180 o from gap. Standard length is 1" braid or armor hose with 14" leads. ig. ig. D Overlap lange: or thermocouple probe holes located through the gap as per ig.. Holes and cut-outs also available. Leads: iberglass insulated lead wires held in place by a clip as per ig. D. Standard position is 180 o from gap. Phone: Toll ree: ax: Toll ree ax: ORDER TOLL REE 451

3 ig. P ig. C Quick Disconnect Plug: U.L. approved plugs can be attached with Bracket - ig. P; Conduit - ig. A and C; Braid - ig. L. can also be supplied with #110 European Plug. Mounting Configurations ig. R: Quick Release Clamp Assembly with 1/4-0 bolt. ig. E: Standard mounting method on all configurations. ig. ES: Spring loaded screw is available to compensate for thermal expansion and contraction (over 18" diameter) ig. : Quick Release Barrel ut Assembly with 1/4-0 bolt. Dual Voltage 3 phase Ground lead or terminal Stainless steel shroud Oversize gap Additional Variations Boxes fitted with hose or braid Perforated shroud without insulation #110 European Plug Partial coverage Additional insulation 45 Phone: Toll ree: ax: Toll ree ax: ORDER TOLL REE

4 I.D. Width Wattag e Voltage ig. # 's BMS Catalog umber Phone: Toll ree: ax: Toll ree ax: Price 1-11 Pcs /4-1/ 50 S 3400C / 500 B 3401C B 340C / B 3403C B 3404C S 3405C B 3406C S 3407C /8 65 S 3408C / S 3409C B 3410C / B 3411C B 110C B 341C B 1103C B 3413C / B 1104C B 3414C B 117C B 3415C S 3416C / B 3417C / B 3418C B 3419C C B 341C C B 34C B 343C / C B 1109C / S 345C B 346C / S 347C B 118C C / B 1110C B 348C C S 349C / S 3430C B 1114C B 3460C ORDER TOLL REE 453

5 454 I.D. 6-3/ / Width Wattag e Voltage ig. # 's BMS Catalog umber Phone: Toll ree: ax: Toll ree ax: Price 1-11 Pcs B 3431C / 343C B 3433C S 3434C S 3435C / B 1116C B 3436C / B 3437C B 3438C B 3439C / 3750 / 1119C C B 110C / S 3441C B 111C / B 344C / B 3443C / / B 3444C S 3445C C B 3446C / B 3447C / B 3448C / B 3449C / 115C / S 3450C / S 3451C C B 3453C / / S 3454C / S 117C / 3455C A 119C / S 3456C / S 3457C B 1130C B 1131C / S 3461C / B 3458C / / 4 600/Half /Half Pc. 1133C C B 1135C C ORDER TOLL REE