~ :H:OlVD.A. CB1000C CLUTCH Date of Issue: Sept., 1982 HONDA MOTOR CO., LTD.
|
|
- Crystal Gilmore
- 6 years ago
- Views:
Transcription
1 ~ :H:OlVD.A. CB1000C
2 ~ :H:OlVD.A. CB1000C 8. SERVICE INFORMATION TROUBLESHOOTING COVER REMOVAL REMOVAL INSTAllATION COVER INSTAllATION STARTER DISASSEMBLY STARTER ASSEMBLY SERVICE INFORMATION GENERAL This section covers removal and installation of the clutch and starter clutch. ~ Clutch maintenance can be done with the engine in the frame. SPECI FICATIONS ADrive Lever B gear free O. play D. (at mm SERVICE lever ( end) mm mm LIMIT (39.91 (1.59 kg/27.4 (3/8-3/4 mm kg/27.4 in) mm in) Ibs/1.08 mm (0.13 (1.53 mm ( ( in) mm in) in) in) STANDARD in) 0.30 mm (0.012 in) - TORQUE VALUES Clutch lock nut Primary drive gear lock bolt Starter clutch locking bolt Spark advancer bolt N m ( kg-m, ft-ib) N m ( kg-m, ft-ib) N m ( kg-m, ft-ib) N m ( kg-m, ft-ib) TOO LS Special Primary Gear Holder Clutch Center Holder 10 mm Socket Bit Common Lock Nut Wrench 20 x 24 mm Handle Not available in U.S.A or or Commercially available in U.S.A or or Commercially available in U.S.A
3 ~ :H:OlVD.A. CB1000C TROUBLESHOOTING Clutch Faulty clutch operation can usually be corrected by adjusting the free play. Clutch slips 1. No free play. 2. Discs worn. 3. Springs weak. Clutch will not disengage 1. Too much free play. 2. Plates warped. Motorcycle creeps with clutch disengaged 1. Too much free play. 2. Plates warped. Excessive lever pressure 1. Clutch cable kinked, damaged or dirty. 2. Lifter mechanism damaged. Clutch operation feels rough 1. Outer drum slots rough
4 ~ ~OlVD.A. CB1000C COVER REMOVAL MUFFLER PROTECTOR COVER Drain the engine oil thoroughly (Page 2-2). Disconnect the clutch cable at the lower adjuster and remove the rear brake pedal and right foot peg. Remove the muffler protector. Remove the clutch cover, gasket and dowel pins. RIGHT FOOT PEG BRAKE PEDAL LI FTER REMOVAL ADJUSTI NG ARM SHAFT Remove the adjusting arm. Remove the clutch lifter shaft
5 ~:H:OIV:D.A. ~ CB1000C REMOVAL Remove the bolts and lifter plate with the clutch lifter guide and release bearing. NOTE Loosen the bolts in a crisscross pattern in 2-3 steps. Remove the clutch springs. LI FTE R PLATE Straighten the lock washer tab. LOCK NUT WRENCH, 20 x 24 mm OR EXTENSION Install the clutch holder on the clutch center with three, 6 mm bolts. Remove the lock nut, lock washer and washer. The clutch can now be removed as a unit. CENTER HOLDER R PRESSURE Remove the clutch assembly. ~/
6 ~~OIVD.A. ~ CB1000C ~ SPRING INSPECTION Measure the spring free lengths. Replace the springs if they are shorter than the service limit. STANDARD: 40.3 mm (1.59 SERVICE LIMIT: 38.9 mm (1.53 in) DISC INSPECTION Replace the clutch discs if they show signs of scoring or discoloration. Measure the disc thickness. STANDARD: mm ( in) SERVICE LIMIT: 3.4 mm (0.13 in) PLATE INSPECTION Check for plate warpage on a surface plate, using a feeler gauge. SERVICE LIMIT: 0.30 mm (0.012 in)
7 ~ :H:O!\TD.A. CB1000C PRIMARY DRIVE GEAR REMOVAL Hold the primary drive gear with the primary gear holder as shown. Loosen the lock bolt. PRIMARY DRIVE GEAR PRIMARY GEAR HOLDER (NOT AVAILABLE IN U.S.A.) INSTAllATION LOCK WASHER Install the primary drive gear with the large gear facing out. Install the collar and lock washer as shown. Tighten the lock bolt. TORQUE: N m ( kg-m, ft-ib) PIN HOLE CO L LA R PRIMARY GEAR HOLDER (NOT AVAILABLE IN U.S.A.) 10 mm SOCKET BIT (COMMERCIALLY AVAILABLE IN U.S.A.) PRIMARY DRIVE GEAR LOCK BOLT
8 ~ :H:OlVD.A. CB1000C ~ OUTER NEEDLE BEARING REPLACEMENT Remove the needle bearings as shown. Install the needle bearing into the clutch outer with the number on the bearing facing out. Install the washer and clutch outer. WASHER ATTACHMENT PI LOT 25 mm x 35 mm CO L LA R WASHER Install the washer and collar. Assemble the clutch discs A and B, plate A and B, clutch pressure plate, and clutch center. NOTE PLATE B Before installing the clutch, coat the discs and plates with engine oil. Install disc B with the grooves facing in the direction shown. CENTER PRESSURE PLATE PLATE A(6) DISC B 8-7
9 ~ :H:OlVD.A. CB1000C Install the clutch assembly, by rotating the clutch center. Install the plain washer with the "OUTSI DE" mark facing out. WASHER Position the lock washer as shown. Install the lock nut with the chamfer facing out. LOCK WASHER LOCK NUT
10 ~:H:OlVD.A. ~ CB1000C ~ Install the clutch holder on the clutch center with three, 6 mm bolts. LOCK NUT WRENCH, 20 x 24 mm OR Tighten the lock nut. TORQUE: N m ( kg-m, ft-ib) ~ Bend the lock washer tab as shown. Install the clutch springs, lifter plate, bearing and Iifter guide. Tighten the bolts. CENTER HOLDER R Install the clutch spring, lifter plate, lifter guide and release bearing. Tighten the bolts. NOTE Tighten the bolts in a crisscross pattern in 2-3 steps. COVER INSTAllATION Install the clutch lifter cam and shaft washer. Insert the cotter pin and spread the ends. HONDA MOTOR CO., L TD
11 ~ :H:Ol\T:D.A. CB1000C Install the adjusting arm and spring. ADJUSTI NG ARM SHAFT Install the dowel pins and gasket, and then install the cover. GASKET DOWEL PINS Adjust the clutch (Page 3-19). Apply grease to the adjusting hole cap O-ring and install. a-ring
12 ~:H:OIVD.A. ~ CB1000C STARTER DISASSEMBLY Remove the left crankcase cover with the pulse generator assembly. LEFT CRANKCASE COVER Remove the spark advancer unit. PIN AND HOLE ADVANCER LOCK SOL T CRANK SHAFT SPACER SPARK ADVANCER UNIT SPARK ADVANCER Remove the starter clutch assembly. STARTER
13 ~ :H:OIV:D.A. CB1000C Remove the starter driven gear and shaft. DRIVEN GEAR SHAFT Inspect the rollers for smooth operation. Remove the rollers and check for excessive wear. Clean all parts with non-flammable or high flash point solvent. PLUNGER STARTER DRIVE GEAR INSPECTION STANDARD: mm ( in) SERVICE LIMIT: mm ( in) Inspect the drive gear for damage or excessive wear. Measure the 0.0. of the drive gear collar
14 (;;ij\:h:olvd.a. ~ CB1000C STARTER ASSEMBLY Install the springs, plungers and rollers. Tighten the locking bolts to the specified torque. TORQUE: N m ( kg-m, ft-ib) NOTE Apply a locking agent to the locking bolt's threads. SLOT PIN Install the spacer aligning the tangs with the holes, and tighten the advancer lock bolt to the 'specified ~j torque. TORQUE: N m ( kg-m, ft-ib) Install the left crankcase cover. PIN AND HOLE Install the advancer assembly. Align the pin on the spark advancer unit with the slot on the crankshaft. CRANK SHAFT SPARK ADVANCER UNIT
~ :H:OlVD.A. CB1000C SUBTRANSMISSION Date of Issue: Sept., 1982 HONDA MOTOR CO., LTD.
SUBTRANSMISSION ~ :H:OlVD.A. CB1000C 10-0 138 ~ :H:OlVD.A. CB1000C 1 O. SUBTRANSMISSION SERVICE INFORMATION TROUBLESHOOTING SUBTRANSMISSION DISASSEMBLY SUBTRANSMISSION ASSEMBLY SUBTRANSMISSION CASE REMOVAL
More informationKICK STARTER/DRIVE PULLEY/ CLUTCH/DRIVEN PULLEY SERVICE INFORMATION TROUBLESHOOTING KICK STARTER DRIVE BELT...
8 KICK STARTER/DRIVE PULLEY/ 8 SERVICE INFORMATION... 8-2 TROUBLESHOOTING... 8-2 KICK STARTER... 8-3 DRIVE BELT... 8-7 DRIVE PULLEY... 8-9 STARTER ONE-WAY CLUTCH DRIVE GEAR... 8-11... 8-14 8-0 Torque:
More informationCVT Continuously Variable Transmission
4. CVT Continuously Variable Transmission XCITING 400i CVT Continuously Variable Transmission This chapter covers the location and servicing of the CVT components for the KYMCO XCITING 400i. Belt Case...
More information8. DRIVE AND DRIVEN PULLEYS/
8 DRIVE AND DRIVEN PULLEYS/ SCHEMATIC DRAWING ---------------------------------------------- 8-1 SERVICE INFORMATION -------------------------------------------- 8-2 TROUBLESHOOTING -------------------------------------------------
More information8 TROUBLESHOOTING
8 DRIVE AND DRIVEN PULLEYS/ SCHEMATIC DRAWING------------------------------------------------------------------------- 8-1 SERVICE INFORMATION-----------------------------------------------------------------------
More information9. DRIVE AND DRIVEN PULLEYS/ KICK STARTER AGILITY ~6.0kg-m g-m g-m 9-0
9 5.0~6.0kg-m 3.5-4.5g-m 9 3.5-4.0g-m 9-0 SERVICE INFORMATION...9-1 DRIVE BELT...9-5 TROUBLESHOOTING...9-1 DRIVE PULLEY...9-6 LEFT CRANKCASE COVER...9-2 CLUTCH/DRIVEN PULLEY...9-9...9-2 SERVICE INFORMATION
More information9. DRIVE AND DRIVEN PULLEYS/ KICK STARTER AGILITY CITY ~6.0kg-m g-m g-m 9-0
9 5.0~6.0kg-m 3.5-4.5g-m 9 3.5-4.0g-m 9-0 SERVICE INFORMATION...9-1 DRIVE BELT...9-5 TROUBLESHOOTING...9-1 DRIVE PULLEY...9-6 LEFT CRANKCASE COVER...9-2 CLUTCH/DRIVEN PULLEY...9-9...9-2 SERVICE INFORMATION
More informationTROUBLESHOOTING. Avoid getting grease and oil on the drive belt and pulley faces.
8 KICK STARTER/DRIVE PULLEY/ SERVICE INFORMATION... 8-2 TROUBLESHOOTING... 8-2 LEFT CRANKCASE COVER... 8-3 DRIVE PULLEY... 8-3... 8-7 KICK STARTER... 8-14 0 1 SERVICE INFORMATION GENERAL INSTRUCTIONS Avoid
More information15 0 Date of Issue: Sept., ~ :H:OlVD.A. CB1000C N m ( kg-m, ft-ib) 4-7 N m ( kg-m, 3-5 ft-ib)
~ :H:OlVD.A. CB1000C 50-70 N m (5.0-7.0 kg-m, 36-51 ft-ib) 4-7 N m (0.4-0.7 kg-m, 3-5 ft-ib) 30-40 N m (3.0-4.0 kg-m, 22-29 ft-ib) 19-23 N m (1.9-2.3 kg-m, 14-17 ft-ib) 15-20 N m (1.5-2.0 kg-m, 11-14 ft-ib)
More information3. LUBRICATION SYSTEM
3 3 LUBRICATION SYSTEM SERVICE INFORMATION------------------------------------------------ 3-2 TROUBLESHOOTING----------------------------------------------------- 3-2 ENGINE OIL/OIL FILTER ------------------------------------------------
More information6. FUEL SYSTEM 6-1 SYSTEM COMPONENTS 6-2 CARBURETOR 6-5 SERVICE INFORMATION 6-2 CARBURETOR HEATER (EXCEPT CO, III LA TYPES) 6-10 TROUBLESHOOTING 6-3
dummytext 6. FUEL SYSTEM 6 SYSTEM COMPONENTS 6-2 SERVICE INFORMATION 6-2 TROUBLESHOOTING 6-3 AIR CLEANER HOUSING 6-4 CARBURETOR 6-5 CARBURETOR HEATER (EXCEPT CO, III LA TYPES) 6-10 PILOT SCREW ADJUSTMENT
More information7. FUEL SYSTEM ('04 - '05)
7. FUEL SYSTEM ('04 - '05) SYSTEM COMPONENTS 7-2 CARBURETOR DISASSEMBLY 7-81 SERVICE INFORMATION 7-3 CARBURETOR ASSEMBLY 7-14 TROUBLESHOOTING 7-4 CARBURETOR INSTALLATION 7-21 AIR CLEANER HOUSING 7-5 PILOT
More information18_25~~ VI ~.' ""'~. ~~ ft lb), f? 8-13 N m qj ~O..f9 ( kg-m. .0 ~J. I i~" C;Q () 0 ~,t) ~ ft lb), ~, ' ~.
~El:OlV:D.A. FRONT: 25-35 N m (2.5-3.5 kg-m, 18_25~~ REAR: 30-40 N m (3.0-4,0 kg-m VI ~.' ""'~. ~~ 22-29 ft lb), f? 8-13 N m qj ~O..f9 (0.8-1.3kg-m C;Q () 0 ~,t) ~ 1------ 6-9 ft lb),.0 ~J. I i~" ~, '
More information~ :H:OlVD.A CB1000C CRANKSHAFT/PRIMARY Date of Issue: Sept., 1982 HONDA MOTOR CO., LTD.
CRANK/PRIMARY ~ :H:OlVD.A CB1000C 13-0 172 HONDA MOTOR CO., LTD. ~:H:OIVD.A. ~ CB1000C 13. CRANK/PRIMARY.~ SERVICE INFORMATION TROUBLESHOOTiNG PRIMARY REMOVAL PRIMARY DISASSEMBLY PRIMARY CHAIN TENSIONER
More information10. ALTERNATOR/STARTER CLUTCH
10. ALTERNATOR/STARTER CLUTCH SYSTEM COMPONENTS 10-2 SERVICE INFORMATION 10-3 TROUBLESHOOTING 10-3 LEFT CRANKCASE COVER REMOVAL 10-4 STATOR/IGNITION PULSE GENERATOR 10-5 FLYWHEEL/STARTER CLUTCH 10-6 LEFT
More informationALTERNATOR/STARTER CLUTCH/ CAM CHAIN TENSIONER
8 ALTERNATOR/STARTER CLUTCH/ SERVICE INFORMATION------------------------------------------------ 8-2 TROUBLESHOOTING----------------------------------------------------- 8-2 ALTERNATOR REMOVAL ----------------------------------------------
More information13. CRANKCASE/CRANKSHAFT/BALANCER/PISTON/CYLINDER
13. CRANKCASE/CRANKSHAFT/BALANCER/PISTON/CYLINDER COMPONENT LOCATION 13-2 SERVICE INFORMATION 13-3 TROUBLESHOOTING 13-4 CRANKCASE SEPARATION 13-5 CRANKSHAFT 13-7 MAIN JOURNAL BEARING 13-9 CRANKPIN BEARING
More information~ HONDA CB1000C IIOIL PUMP. rw_u LUBRICATION ENGINE LUBRICATION DIAGRAM. Date of Issue: Sept., 1982 HONDA MOTOR CO., ltd.
LUBRICATION ENGINE LUBRICATION DIAGRAM EXHAUST CAMSHAFT ~ HONDA CB1000C INTAKE CAMSHAFT,t Oil FilTER Oil COOLER PRIMARY CHAIN TENSIONER IIOIL PUMP PRIMARY SHAFT TRANSMISSION MAINSHAFT 01 COUNTERSHAFT Oil
More informationSERVICE INFORMATION 11-1 FRONT WHEEL/SUSPENSION/ STEERING XL FRONT WHEEL 11 7 FORK STEERING STEM 11 18
XL200 11. FRONT WHEEL/SUSPENSION/ STEERING SERVICE INFORMATION 11 1 TROUBLESHOOTING 11 2 HANDLEBAR 11 3 FRONT WHEEL 11 7 FORK 11 11 STEERING STEM 11 18 SERVICE INFORMATION GENERAL A contaminated brake
More information1994 Mazda MX-5 Miata. CLUTCH 1994 Clutch
CLUTCH 1994 Clutch DESCRIPTION Miata uses a hydraulically operated clutch. HYDRAULIC SYSTEM BLEEDING 1. Remove bleeder screw cap, located at clutch release cylinder. Install vinyl hose onto bleeder screw.
More information7. CYLINDER HEAD/VALVES
7 7 7-0 SERVICE INFORMATION...7-1 CYLINDER HEAD DISASSEMBLY...7-7 TROUBLESHOOTING...7-2 CYLINDER HEAD ASSEMBLY...7-8 CAMSHAFT REMOVAL...7-3 CYLINDER HEAD INSTALLATION...7-8 CYLINDER HEAD REMOVAL...7-5
More informationOVERHAULING THE ENGINE. 85 Nm (8.5 m kg, 61 ft Ib) Order Job/Part Q ty Remarks Removing the drive sprocket
INE EAS00188 INE DRIVE SPROCKET OVERHAULING THE INE 10 Nm (1.0 m kg, 7.2 ft Ib) 85 Nm (8.5 m kg, 61 ft Ib) Order Job/Part Q ty Remarks Removing the drive sprocket Remove the parts in the order listed.
More informationCHASSIS CONTENTS EXTERIOR PARTS 6-1 FRAME COVER 6-2 REAR FRAME COVER 6-4 FRONT WHEEL 6-6 FRONT BRAKE 6-10 HANDLEBARS 6-17 FRONT FORK 6-19
CHASSIS CONTENTS EXTERIOR PARTS 6- FRAME COVER 6- REAR FRAME COVER 6-4 FRONT WHEEL 6-6 FRONT BRAKE 6-0 HANDLEBARS 6-7 FRONT FORK 6-9 STEERING 6-6 REAR WHEEL 6-3 REAR BRAKE 6-39 6 REAR SHOCK ABSORBER 6-43
More informationEngine Removal/Installation
Engine Removal/Installation Make sure jacks and safety stands are placed properly and hoist brackets are attached to correct positions on the engine. (See Section 1). Apply parking brake and block rear
More information23. ELECTRIC STARTER (TRX450ER)
23. ELECTRIC STARTER (TRX450ER) COMPONENT LOCATION 23-2 STARTER MOTOR 23-6 SYSTEM DIAGRAM 23-2 STARTER RELAY SWITCH 23-13 SERVICE INFORMATION 23-3 CLUTCH DIODE 23-14 TROUBLESHOOTING 23-4 23-1 COMPONENT
More informationENG CRANKCASE AND REED VALVE. REED VALVE INSPECTION 1. Measure: 8 Valve stopper height 1 Out of specification Adjust stopper/replace valve stopper.
CRANKCASE AND REED VALVE ENG REED VALVE INSPECTION. Measure: 8 Valve stopper height Out of specification Adjust stopper/replace valve stopper. Valve stopper height 6.0~6. mm(0.~0.5 in). Measure: 8 Reed
More informationGftOUP 4 PARKING BHAKE
PARKING BRAKE 4-1 GftOUP 4 PARKING BHAKE CONTENTS Page Data and Specifications... 1 External Contracting Type Parking Brake...... 2 Parking Brake Band Lining 3 Parking Brake Internal Expanding Type 5 Parking
More informationSPECIFICATIONS UNIT. mm (in)
XL200 12. REAR WHEEL/ SUSPENSION SERVICE INFORMATION 12 1 TROUBLESHOOTING 12 2 REAR WHEEL 12 3 REAR BRAKE 12 7 REAR BRAKE PEDAL 12 10 SHOCK ABSORBERS 12 11 SHOCK LINKAGE 12 13 SWINGARM 12 15 SERVICE INFORMATION
More informationINSTALLATION GUIDE CRF150R Manual Revision:
REKLUSE MOTOR SPORTS The z-start Pro Clutch INSTALLATION GUIDE CRF150R 191-810 Manual Revision: 032508 2002 Rekluse Motor Sports Rekluse Motor Sports, Inc. 110 E. 43rd Street Boise, Idaho 83714 208-426-0659
More information1992 Clutch. Eclipse, Expo/Expo LRV, Galant, Mirage, Precis, 3000GT
Article Text ARTICLE BEGINNING 1992 Clutch Eclipse, Expo/Expo LRV, Galant, Mirage, Precis, 3000GT DESCRIPTION All clutches are single disc type. Pressure plate assembly uses a diaphragm spring to engage
More informationPart list for Kawasaki H2, 1972
Part list for Kawasaki H2, 972 . Cylinder head, cylinder. . Cylinder head, cylinder. 9205-049 NUT 0 m/m 2 2 40B400 WASHER-plain 4 m/m 2 3 46E400 WASHER-spring 4 m/m 2 4 92070-036 SPARK PLUG NGK B9 HS 3
More informationCHAPTER 4. CARBURETION
CHAPTER 4. CARBURETION CARBURETOR... 4l SECTIONAL VIEW.... 42 REMOVAL... 44 DISASSEMBLY... 44 INSPECTION... 47 ASSEMBLY... 48 INSTALLATION....4l 1 ADJUSTMENT....4l 1 1 C A R B U R E T O R CARBURETOR @connection
More informationATV 50 Y-6 YOUTH CAT GREEN (A2004ATA2BUSZ) Page 1 of 50 A-ARM, FLOOR PANEL, AND BUMPER ASSEMBLY
2004 ATV 50 Y-6 YOUTH CAT GREEN (A2004ATA2BUSZ) Page 1 of 50 A-ARM, FLOOR PANEL, AND BUMPER ASSEMBLY 2004 ATV 50 Y-6 YOUTH CAT GREEN (A2004ATA2BUSZ) Page 2 of 50 A-ARM, FLOOR PANEL, AND BUMPER ASSEMBLY
More informationTransmission/Crankshaft/Crank Case
R.Crank Case Crankshaft L.Crank Case 11-0 11. Transmission/Crankshaft/Crank Case Transmission/Crankshaft/Crank Case Service Information 11-1 Troubleshooting 11-2 Transmission 11-3 Crank Case Disassembly
More informationENG V-BELT AUTOMATIC TRANSMISSION Tighten: primary sheave nut 1
V-BELT AUTOMATIC TRANSMISSION 2 1 5. Tighten: primary sheave nut 1 Nm (16.0 m kg, 115 ft lb) T R.. 160 CAUTION: Before tightening the nut to remount the primary sheave, make sure that the serrations of
More information5/30/2014 F2.5MSH 0407 / TOP COWLING Yamaha Motor Corporation, U.S.A. All rights reserved.
F.5MSH 0407 Page of 40 5/30/04 F.5MSH 0407 / TOP COWLING 04 Yamaha Motor Corporation, U.S.A. All rights reserved. F.5MSH 0407 Page of 40 5/30/04 Part List F.5MSH 0407 / TOP COWLING REF - NO PART NUMBER
More informationOPERATING INSTRUCTIONS AND SERVICE MANUAL
OPERATING INSTRUCTIONS AND SERVICE MANUAL 55NAL--270-4 55NL--724-4 55RNL-2-LS-4- COMPLETE TOOL MODEL NO. CODE NO. 55NAL--270-4 20270 55NL--724-4 220724 READ SAFETY RECOMMENDATIONS 55RNL-2-LS-4-24089 BEFORE
More informationRekluse Motor Sports. The z-start Clutch GAS GAS. 200, 250, and strokes. 400 and strokes
Rekluse Motor Sports The z-start Clutch GAS GAS 200, 250, and 300 2-strokes 400 and 450 4-strokes Installation Guide Copyright 2002-2004 Rekluse Motor Sports z-start Revision 3.000 RMS100 Gas Gas z-start
More information5/30/2014 F2.5LMHA 0313 / SCHEDULED SERVICE PARTS Yamaha Motor Corporation, U.S.A. All rights reserved.
F.5LMHA 033 Page of 4 5/30/04 F.5LMHA 033 / SCHEDULED SERVICE PARTS 04 Yamaha Motor Corporation, U.S.A. All rights reserved. F.5LMHA 033 Page of 4 5/30/04 Part List F.5LMHA 033 / SCHEDULED SERVICE PARTS
More informationPARTS CATALOGUE. Rockford Motors inc.
PARTS CATALOGUE Rockford Motors inc. INSTRUCTIONS FOR USING THE PARTS CATALOGUE 1. This catalogue covers all the items of genuine parts and tools of BRIDGESTONE 350 GTR and 350 GTO motorcycles. 2. Please
More informationCLUTCH Nissan 240SX DESCRIPTION PEDAL HEIGHT & FREE PLAY ADJUST CLUTCH ASSEMBLY R & I Clutch. Pathfinder, Pickup, 240SX, 300ZX
CLUTCH 1990 Nissan 240SX 1990 Clutch Pathfinder, Pickup, 240SX, 300ZX DESCRIPTION Clutch is of dry, single disc type, with a diaphragm spring type pressure plate. Clutch release bearing is prelubricated.
More information10. CRANKCASE/CRANKSHAFT/TRANS- MISSION SYSTEM/STARTER SPINDLE CK
10 10 10-0 SERVICE INFORMATION... 10-1 STARTER SPINDLE... 10-6 TROUBLESHOOTING... 10-2 CRANKSHAFT... 10-8 CRANKCASE REMOVAL... 10-3 CRANKCASE INSTALLATION... 10-10 TRANSMISSION SYSTEM... 10-3 SERVICE INFORMATION
More information613GC Key A Parts Starter & Ignition Assembly
613GC Key A Parts Starter & Ignition Assembly 73866 Screw (same as B26) A01 505514 Starter Rope Handle A02 73904 Starter Rope A03 73909 Starter Coil Spring & Housing A04 71451 Starter Case Plate A05 73910
More informationINSTALLATION GUIDE. Clutch Cable Actuated Models Manual Revision:
REKLUSE MOTOR SPORTS The z-start Pro Clutch INSTALLATION GUIDE Clutch Cable Actuated Models 191-800 Manual Revision: 041513 2012 Rekluse Motor Sports Rekluse Motor Sports, Inc. 12000 W Franklin Rd. Boise,
More informationSmall Engine Parts. 306A Gas Chain Page Saw 1 of 10 Carburetor & Choke Assembl
Small Engine Parts 306A Gas Chain Page Saw 1 of 10 Carburetor & Choke Assembl 1 530001686 2 Screw 2 530010049 1 Crankcase 3 530019022 1 Gasket - Carburetor - Adapter to C/Case Included in Gasket Kit 4
More informationSSR200 Zongshen 200cc Dirt Bike (VIN PREVIX LZSJ)
Page 1 of 19 Product Information Baja Web > Product Information > Parts Lists > DIRTBIKE > SSR200 Zongshen 200cc Dirt Bike (VIN PREVIX LZSJ) SSR200 Zongshen 200cc Dirt Bike (VIN PREVIX LZSJ) SSR200 Zongshen
More informationTCI Turbo 400 Full Manual Valve Body. Shift Pattern: Park Reverse Neutral First Second Third. NOTE: You must reuse stock manual control valve.
TCI 221100 Turbo 400 Full Manual Valve Body Shift Pattern: Park Reverse Neutral First Second Third This Kit Contains: (1) Turbo 400 Full Manual Valve Body (1) Separator Plate & Gaskets (1) Pressure Regulator
More informationFUEL SYSTEM CIRCUIT D'ESSENCE KRAFTSTOFFSYSTEM
CIRCUIT D'ESSENCE KRAFTSTOFFSYSTEM 41 FUEL SYSTEM SERVICE INFORMATION TROUBLESHOOTING FUEL TANK AIR CLEANER CARBURETOR REMOVAL VACUUM CHAMBER FLOAT CHAMBER 4-1 PILOT SCREW 4-2 CARBURETOR SEPARATION 4-3
More information5/29/2014 3MSHU 1996 / CYLINDER CRANKCASE Yamaha Motor Corporation, U.S.A. All rights reserved.
Page 1 of 22 3MSHU 1996 / CYLINDER CRANKCASE Page 2 of 22 Part List 3MSHU 1996 / CYLINDER CRANKCASE REF - NO PART NUMBER PART NAME QUANTITY REMARKS 1 6L5-W0090-01-4D CRANK CYLINDER ASSEMBLY 1 2 6L5-15100-00-94
More information90 Utility Model Number A2013KUB2BUSZ SHARE OUR PASSION.
2013 90 Utility Model Number A2013KUB2BUSZ TM SHARE OUR PASSION. TABLE OF CONTENTS 2013 ATV 90 (Model No. A2013KUB2BUSZ) BODY PANEL AND HEADLIGHT ASSEMBLY... 1 FRONT AND REAR RACK ASSEMBLY... 2 FRAME AND
More information5/29/2014 3MSHY 2000 / CYLINDER CRANKCASE Yamaha Motor Corporation, U.S.A. All rights reserved.
Page 1 of 22 3MSHY 2000 / CYLINDER CRANKCASE Page 2 of 22 Part List 3MSHY 2000 / CYLINDER CRANKCASE REF - NO PART NUMBER PART NAME QUANTITY REMARKS 1 6L5-W0090-01-1S CRANK CYLINDER ASSY 1 2 6L5-15100-00-1S
More informationFINAL REDUCTION/TRANSMISSION SYSTEM
11 FINAL REDUCTION/ SERVICE INFORMATION------------------------------------------------ 11-2 TROUBLESHOOTING----------------------------------------------------- 11-2 SECONDARY DRIVE/DRIVEN BEVEL GEAR
More informationAmerican Honda Motor Co., Inc.
PROGRAMS AND DATA ARE THE PROPERTY OF AMERICAN HONDA MOTOR CO., INC. Parts List 001 COVER, CRANKCASE W 001 11100-812-020 0100001-1004270 001 COVER, CRANKCASE 001 11100-812-030 1004271-1018081 001 COVER,
More informationBOTTOM END SERVICE TOOLS SERVICE PRODUCTS ENGINE, CVT AND GEARBOX Subsection 10 (BOTTOM END)
BOTTOM END SERVICE TOOLS Description Part Number Page CRANKCASE SUPPORT MAG/PTO... 529 036 031... 151 CRANKSHAFT LOCKING BOLT... 529 035 617... 154 DRIVE SHAFT OIL SEAL INSTALLER... 529 036 028... 143
More information~. a~' ~ ( I o~~~ 4-0. ~Sj~' AO~ i/~ CB1000C (ij)aon'da in-ib) ~ "" ~ ~!~~P. ~ J N m (6-12 kg-em,
e V ~. a~' ~ I ~ J C t \"" 8.0- ( I o~~~ ~ "" ~ ~. ~!~~P. C8 0 & 0,-t. ~ CB1000C (ij)aon'da 0.6-1.2 N m (6-12 kg-em, 5-10 in-ib) 4-0 / 4.0-6.0 N m (40-60 kg-em, 35-52 in-i b) t$ "'07~ / c;:::/ j ~Sj~'
More informationRekluse Motor Sports. The z-start Clutch CRF 250X. Installation Guide Copyright 2002 Rekluse Motor Sports z-start Revision RMS116 CRF 250X
Rekluse Motor Sports The z-start Clutch CRF 250X Installation Guide Copyright 2002 Rekluse Motor Sports z-start Revision 3.000 RMS116 CRF 250X 191-216 Manual Revision: 103105 Rekluse Motor Sports, inc.
More informationB B B
FIG CYLINDER Suzuki Worldwide Motorcycle-ATV Page: of -0B00-00 0-00 0-000 0-00 0-0B0-0B0 0-0 0-0 Head, Cylinder Gasket, Cylinder Head Spark Plug (ngk,bphs) Spark Plug (nd,wfp-u) Cylinder Gasket, Cylinder
More informationAUTOMATIC TRANSMISSIONS Mitsubishi F3A20 Series TRANSMISSION APPLICATION TABLE
Article Text ARTICLE BEGINNING AUTOMATIC TRANSMISSIONS Mitsubishi F3A20 Series APPLICATION TRANSMISSION APPLICATION TABLE Vehicle Application Transmission Model Colt 3-Speed (1990-94)... F3A21 Colt Vista
More informationX4 (GREEN) (A2000ATF2AUSG) Page 1 of 80 AIR INTAKE ASSEMBLY
2000 300 2X4 (GREEN) (A2000ATF2AUSG) Page 1 of 80 AIR INTAKE ASSEMBLY 2000 300 2X4 (GREEN) (A2000ATF2AUSG) Page 2 of 80 AIR INTAKE ASSEMBLY Ref # Part Number Qty S/P/F Description 1 3570-001 1 /P Intake,
More informationSERVICE INFORMATION 5-1 ENGINE REMOVAL/ ENGINE INSTALLATION 5-3 SERVICE INFORMATION 5-1 ENGINE REMOVAL 5-2 GENERAL
ENGINE REMOVAL/ XL200 5. INSTALLATION SERVICE INFORMATION 5-1 ENGINE REMOVAL 5-2 ENGINE INSTALLATION 5-3 SERVICE INFORMATION GENERAL When removing the engine, support the motorcycle on its center stand.
More informationSherco Engine Teardown and Assembly Manual
Sherco Engine Teardown This Manual is provided as a guide for: Removing the engine from the frame Splitting the cases Complete Disassembly of the engine Reassembly of the engine Reinstallation back in
More informationPREPARATIONS AND PRECAUTIONS for Disassembly & Reassembly
Chapter I Engine PREPARATIONS AND PRECAUTIONS for Disassembly & Reassembly Use genuine parts. With regards to the oil, adhesive and sealing agent, also use genuine or recommended one. With regards to gasket,
More informationSuper XL 925 Chain Saw UT Page 1 of 15 Carburetor Chamber
Super XL 925 Chain Saw UT-10415 Page 1 of 15 Carburetor Chamber Super XL 925 Chain Saw UT-10415 Page 2 of 15 Carburetor Chamber 1 63370A 1 RETAINER- Reed valve 2 63166A 4 VALVE- Reed 3 63371B 1 SEAT- Reed
More informationSuper EZ Chain Saw UT Page 1 of 18 Tools And Accessories
Super EZ Chain Saw UT-10440 Page 1 of 18 Tools And Accessories Super EZ Chain Saw UT-10440 Page 2 of 18 Tools And Accessories 24299 24299 ANVIL- Crankshaft installation 24304 24304 BIT- #2 pozidrive 24295
More informationRekluse Motor Sports. The z-start Clutch. Cannondale
Rekluse Motor Sports The z-start Clutch Cannondale Installation Guide Copyright 2002-2004 Rekluse Motor Sports z-start Revision 3.000 RMS105 Cannondale 191-205 Manual Revision: 091304 Rekluse Motor Sports,
More information90 Y-12 Youth. Model Number A2005H4B2BUSR (Red) Model Number A2005H4B2BUSZ (Cat Green) Illustrated Parts Manual
90 Y-12 Youth Model Number A2005H4B2BUSR (Red) Model Number A2005H4B2BUSZ (Cat Green) Illustrated Parts Manual 2005 TABLE OF CONTENTS 2005 ATV 90 Y-12 Youth Red (Model No. A2005H4B2BUSR) Cat Green (Model
More informationSMF / DSF / DTF SMF / DSF / DTF 200
2006 SMF / DSF / DTF 200 1 The drawings in this parts book have been scaled so that parts can be easily recognized. 1 CYLINDER ASSY 2 CYLINDER ASSY Ref # Part # Description 1 410 0001A CYLINDER HEAD COVER
More informationHusqvarna Hedgetrimmers 325HS/ 325HE/ 325HDA. Workshop manual
Husqvarna Hedgetrimmers 325HS/ 325HE/ 325HDA Workshop manual 101 90 73-26 2 Workshop Manual Hedge trimmers Supplement for models 325HS, 325HE,325HDA Contents 1. Starter 5 2. Ignition system 7 3. Fuel system
More informationRemoval and Installation of Fuel Injection Pumps
Page 16 of 126 worn considerably. Fig. C shows how the flat end of a new plunger makes poor contact with a worn lifter, resulting in rapid wear to both parts. An injection pump can have a good fuel flow
More informationSPECIFICATIONS TEST AND ADJUSTMENT SPECIFICATIONS SPECIFICATIONS ENGINE FD620D, K SERIES
ENGINE FD620D, K SERIES SPECIFICATIONS SPECIFICATIONS TEST AND ADJUSTMENT SPECIFICATIONS Engine Oil Pressure Sensor Activates............................... 98 kpa (14.2 psi) Oil Pressure While Cranking
More informationEngine Does Not Start or Is Hard to Start Cause of Trouble. 1. Open the drain screw, and check Fuel not supplied (1) Fuel tank empty
20. Engine Does Not Start or Is Hard to Start 20-1 Engine Output Insufficient 20-2 Poor Performance at Low Speed and Idling 20-3 Poor Performance at High Speed 20-3 Unsatisfactory Operation 20-4 Fuel Gauge
More information11. ALTERNATOR/STARTER CLUTCH
11. ALTERNATOR/STARTER CLUTCH COMPONENT LOCATION 11-2 SERVICE INFORMATION 11-3 TROUBLESHOOTING 11-3 STATOR REMOVAL 11-4 FLYWHEEL/STARTER CLUTCH 11-6 STATOR INSTALLATION 11-12 11 11-1 ALTERNATOR/STARTER
More informationBR-250 / BR-250SS / M2-250 SERVICE MANUAL
BR-250 / BR-250SS / M2-250 SERVICE MANUAL Manufactured by PGO of Motive Power Industry Co., Ltd 1. INSPECTION/ADJUSTMENT 1 1 INSPECTION/ADJUSTMENT SERVICE INFORMATION -------------------------------------------------
More informationRekluse Motor Sports. The z-start Clutch LTR 450. Installation Guide Copyright 2002 Rekluse Motor Sports z-start Revision 3.
Rekluse Motor Sports The z-start Clutch LTR 450 Installation Guide Copyright 2002 Rekluse Motor Sports z-start Revision 3.000 RMS166 LTR 450 191-266 Manual Revision: 032306 Rekluse Motor Sports, inc. 110
More informationSuper EZ Chain Saw UT Page 1 of 19 Carburetor
Super EZ Chain Saw UT-10580 Page 1 of 19 Carburetor Super EZ Chain Saw UT-10580 Page 2 of 19 Carburetor 1 93203A 1 /P Repair Kit Includes items 1-16. 2 93203A 1 /P Repair Kit Includes items 1-16. 3 93203A
More informationINSTALLATION GUIDE. Clutch Cable Actuated Models Manual Revision:
REKLUSE MOTOR SPORTS The z-start Pro Clutch INSTALLATION GUIDE Clutch Cable Actuated Models 191-800 Manual Revision: 061810 2002 Rekluse Motor Sports Rekluse Motor Sports, Inc. 110 E. 43rd Street Boise,
More informationRekluse Motor Sports. The z-start Clutch CRF 250R. Installation Guide Copyright 2002 Rekluse Motor Sports z-start Revision RMS112 CRF 250R
Rekluse Motor Sports The z-start Clutch CRF 250R Installation Guide Copyright 2002 Rekluse Motor Sports z-start Revision 3.000 RMS112 CRF 250R 191-212 Manual Revision: 091205 Rekluse Motor Sports, Inc.
More informationCHASSIS CONTENTS EXTERIOR PARTS 6-1 FRONT WHEEL 6-2 FRONT BRAKE 6-6 HANDLEBARS 6-12 REAR WHEEL 6-30 REAR BRAKE 6-34 REAR SHOCK ABSORBER 6-36
CHASSIS CONTENTS EXTERIOR PARTS 6-1 FRONT WHEEL 6-2 FRONT BRAKE 6-6 HANDLEBARS 6-12 FRONT FORK ( ) 6-14 FRONT FORK ( ) 6-20 STEERING 6-27 REAR WHEEL 6-30 REAR BRAKE 6-34 REAR SHOCK ABSORBER 6-36 6 SWING
More informationE1 Cylinder Head Cover
E1 Cylinder Head Cover 1 E0101-001-70E Cover, upper cylinder head 1 2 E0101-002-70E Cover, R. cylinder head 1 3 E0101-003-70E cover, L.cylinder head 1 4 E0101-004-70E Cap, valve chamber 2 5 E0101-005-70E
More information5. FUEL SYSTEM 5-0 FUEL SYSTEM MXU 250R/300R
5 FUEL SYSTEM 5 SERVICE INFORMATION------------------------------------------------ 5-2 TROUBLESHOOTING----------------------------------------------------- 5-3 FUEL TANK -----------------------------------------------------------------
More information12. FRONT WHEEL/FRONT BRAKE/
12 12 12-0 SERVICE INFORMATION... 12-1 FRONT BRAKE... 12-7 TROUBLESHOOTING... 12-2 FRONT SHOCK ABSORBER... 12-18 STEERING HANDLEBAR... 12-3 FRONT FORK... 12-21 FRONT WHEEL... 12-4 SERVICE INFORMATION GENERAL
More informationENGINE CONTENTS CAUTION
ENGINE CONTENTS ENGINE REMOVAL AND REINSTALLATION 3- ENGINE REMOVAL 3- ENGINE REINSTALLATION 3-7 ENGINE DISASSEMBLY 3-9 STARTER MOTER 3-9 THERMOSTAT 3-9 ND AIR VALVE 3-0 CYLINDER HEAD COVER 3-0 PISTON
More information9/7/2014 F9.9MSHV 1997 / CYLINDER CRANKCASE Yamaha Motor Corporation, U.S.A. All rights reserved.
F9.9MSHV 997 Page of 45 9/7/04 F9.9MSHV 997 / CYLINDER CRANKCASE 04 Yamaha Motor Corporation, U.S.A. All rights reserved. F9.9MSHV 997 Page of 45 9/7/04 Part List F9.9MSHV 997 / CYLINDER CRANKCASE REF
More informationRekluse Motor Sports. The z-start Clutch KTM LC4 ( )
Rekluse Motor Sports The z-start Clutch KTM LC4 (1999 2005) Installation Guide Copyright 2002-2004 Rekluse Motor Sports z-start Revision 3.000 RMS630 KTM LC4 191-280 Manual Revision: 103105 Rekluse Motor
More informationCHAPTER 7 TRANSMISSION (MFO6S)
1 page INDEX1 Model SG1J (MF06S) TRANSMISSION 7-1 7-142E-07 CHAPTER 7 TRANSMISSION (MFO6S) Model SG1J 1 Models FE, FF and SG2J 1 Model FD 7 TROUBLESHOOTING...7-2 SPECIAL TOOLS...7-5 REMOVAL...7-7 GEAR
More information330 Chain Saw UT Page 1 of 17 Chain Brake and Chain Stop
330 Chain Saw UT-10609 Page 1 of 17 Chain Brake and Chain Stop 330 Chain Saw UT-10609 Page 2 of 17 Chain Brake and Chain Stop 1 80983 3 SCREW- (8-32 x 1/2) 2 70705 1 STOP- Chain 3 88048 1 SCREW- (10-24
More information10. ENGINE REMOVAL/INSTALLATION
10. SYSTEM COMPONENTS 10-2 ENGINE REMOVAL 10-5 SERVICE INFORMATION 10-4 ENGINE INSTALLATION 10-9 10-1 SYSTEM COMPONENTS '04 - '05: 9.8 N-m (1.0 kgfm, 7 Ibf ft) 108 N-m (11.0 kgf-m, 80 Ibf-ft) 74 N-m (7.5
More informationCYLINDER HEAD. Ref. Part No. Number Description Qty Remarks
A1 CYLINDER HEAD 1 JN6-11102-00-00 HEAD, CYLINDER.......... 1 2 JN6-11133-10-00. GUIDE, VALVE............ 2 3 JN6-11181-00-00 GASKET, CYLINDER HEAD... 1 4 95817-10070-00 BOLT, FLANGE............ 4 5 99530-14016-00
More informationThis file is available for free download at
This file is available for free download at http://www.iluvmyrx7.com This file is fully text-searchable select Edit and Find and type in what you re looking for. This file is intended more for online viewing
More information3. LUBRICATION SYSTEM
3. LUBRICATION SYSTEM Mechanism Diagram 3-1 Precautions in Operation 3-2 Troubleshooting 3-2 Engine Oil 3-3 Engine Oil Strainer Clean 3-3 Oil Pump 3-4 Mechanism Diagram 3-1 3. LUBRICATION SYSTEM Precautions
More informationXL12 Chain Saw UT Page 1 of 21 Carburetor Chamber
XL12 Chain Saw UT-10080 Page 1 of 21 Carburetor Chamber XL12 Chain Saw UT-10080 Page 2 of 21 Carburetor Chamber 1 59274 1 GASKET- Spacer 2 59718 1 SPACER 3 63260A 1 RETAINER- Reed valve 4 63253 1 SEAT-
More information3. LUBRICATION SYSTEM
3. LUBRICATION SYSTEM Mechanism Diagram 3-1 Precautions in Operation 3-2 Troubleshooting 3-2 Engine Oil 3-3 Engine Oil Strainer Clean 3-3 Oil Pump 3-4 Mechanism Diagram 3-1 3. LUBRICATION SYSTEM Precautions
More informationAluminium Clutch Cover Kit Instruction Manual
Aluminium Clutch Cover Kit Instruction Manual Item No. Applied to Ape50 Ape50 (FI) Ape50 (FI Type D) AC18-1000001 Ape100 Ape100 Type D XR50 Motard XR100 Motard Frame No. AC16-1000001 AC16-1600001 HC07-1000001
More informationRekluse Motor Sports, Inc. The z-start Clutch. Husaberg ( )
Rekluse Motor Sports, Inc. The z-start Clutch Husaberg (1989-2003) Installation Guide Copyright 2002-2004 Rekluse Motor Sports z-start Revision 3.000 RMS125 Husaberg 89-03 191-225 Manual Revision: 012805
More informationCHASSIS CONTENTS FRONT WHEEL 6-1 FRONT BRAKE 6-6 FRONT FORK 6-14 STEERING STEM 6-20 REAR WHEEL AND REAR BRAKE 6-25 SUSPENSION 6-31 REAR SWING ARM 6-36
CHASSIS CONTENTS FRONT WHEEL 6-1 FRONT BRAKE 6-6 FRONT FORK 6-14 STEERING STEM 6-20 REAR WHEEL AND REAR BRAKE 6-25 SUSPENSION 6-31 REAR SWING ARM 6-36 6 6-1 CHASSIS FRONT WHEEL REMOVAL Support the machine
More informationCLUTCH CONTENTS SERVICE DIAGNOSIS. (a) Worn or damaged disc assembly. (b) Grease or oil on disc facings. (c) Improperly adjusted cover assembly.
CLUTCH CONTENTS -GROUP 6 Page CLUTCH HOUSING ALIGNMENT... 6 CLUTCH PEDAL FREE PLAY 1 CLUTCH RELEASE BEARING 5 CLUTCH RELEASE FORK... 5 CLUTCH SERVICING 2 PILOT BUSHING CRANKSHAFT TO TRANSMISSION DRIVE
More informationENGINE CONTENTS ENGINE REMOVAL AND REINSTALLATION 3-1 ENGINE REMOVAL 3-1 ENGINE REINSTALLATION 3-5 ENGINE DISASSEMBLY 3-7 STARTER MOTER 3-7
ENGINE CONTENTS ENGINE REMOVAL AND REINSTALLATION 3- ENGINE REMOVAL 3- ENGINE REINSTALLATION 3-5 ENGINE DISASSEMBLY 3-7 3 STARTER MOTER 3-7 CYLINDER HEAD COVER 3-8 PISTON 3- MAGNETO COVER 3-3 MAGNETO ROTOR
More informationATV 50 DVX BLACK-RED (A2008KSA2BUSD) Page 1 of 60 AIR INTAKE ASSEMBLY
2008 ATV 50 DVX BLACK-RED (A2008KSA2BUSD) Page 1 of 60 AIR INTAKE ASSEMBLY 2008 ATV 50 DVX BLACK-RED (A2008KSA2BUSD) Page 2 of 60 AIR INTAKE ASSEMBLY Ref # Part Number Qty S/P/F Description 1 3303-005
More informationTECHNICAL INFORMATION
TECHNICAL INFORMATION Models No. Description EM2650UH/ EM2650LH, EM2651UH/ EM2651LH Petrol Brushcutter W W PRODUCT P 1/ 14 H CONCEPT AND MAIN APPLICATIONS These four 25.4mL Petrol Brushcutters have been
More informationENGINE CONTENTS ENGINE REMOVAL AND REINSTALLATION 3-1 ENGINE REMOVAL 3-1 ENGINE REINSTALLATION 3-5 ENGINE DISASSEMBLY 3-7 STARTER MOTER 3-7
ENGINE CONTENTS ENGINE REMOVAL AND REINSTALLATION 3-1 ENGINE REMOVAL 3-1 ENGINE REINSTALLATION 3-5 ENGINE DISASSEMBLY 3-7 3 STARTER MOTER 3-7 CYLINDER HEAD COVER 3-8 PISTON 3-12 MAGNETO COVER 3-13 MAGNETO
More information