Removal and Installation of Fuel Injection Pumps
|
|
|
- Rose Boone
- 5 years ago
- Views:
Transcription
1 Page 16 of 126 worn considerably. Fig. C shows how the flat end of a new plunger makes poor contact with a worn lifter, resulting in rapid wear to both parts. An injection pump can have a good fuel flow coming from it but not be a good pump because of slow timing that is caused by wear on the bottom end of the plunger. When making a test on a pump that has been used for a long time, use a micrometer and measure the length of the plunger. If the length of the plunger is shorter than the minimum length (worn) dimension given in the chart, install a new pump. Look for wear at the top part of the plunger. Check the operation of the plunger according to the instructions for the Fuel Injection Test Bench. Removal and Installation of Fuel Injection Pumps This procedure can be done with the fuel injection pump housing on or off the engine. Before the 6V7050 Compressor Group is used for the first time, or if the group has been disassembled, make the following adjustment: 1. An injection pump that is to be used for this adjustment (or one that is to be removed or installed) must have another injection pump installed next to it. The second injection pump serves as the compressor mounting stud. If there are not two injection pumps next to each other, install two injection pumps without the lifter springs. See Installation Of Fuel Injection Pumps for the correct alignment of the pump at assembly.
2 Page 17 of 126 Adjustment of 6V7050 Compressor Group (A) 6V7015 Clamp. (B) Bracket assembly. (C) 4B2046 Nut. (D) 8T937 Nut. (E) 2N3476 Screw. 2. Put bracket assembly (B) over one of the pump bonnets. 3. Put the clamp ram on the center of the other injection pump bonnet with screw (E) in contact with the fuel line seat. NOTE: The 6V7015 Clamp (A) should not be locked down. 4. Install and tighten nut (D). 5. Adjust screw in or out until the top of bracket assembly (B) just starts to move when the clamp ram is locked down. 6. Tighten nut (C) to hold screw (E) in position. Removal of Fuel Injection Pumps NOTICE Before any parts are removed from the fuel injection pump housing, thoroughly clean all dirt from the housing. Dirt that gets inside the pump housing will cause much damage. NOTE: The fuel rack must be in the zero (center) position before the fuel injection pumps can be removed or installed. Follow Steps 1 through 5.
3 Page 18 of 126 Fuel Injection Pump Housing (1) Plug (rack centering pin). (2) Cover (rack position indicator). 1. Remove plug (1) and cover (2) from the fuel injection pump housing. Fuel Rack Against Timing Pin in the Zero Position (3) 6V4186 Timing Pin. 2. Install the 6V4186 Timing Pin (3) in the top of the fuel injection pump housing. Make sure timing pin (3) engages in the slot of the fuel rack as shown. Holding Fuel Rack in Zero Position (3) 6V4186 Timing Pin. (4) 8T9198 Bracket Assembly. (5) 1U5426 Compressor Assembly. 3. Install bracket assembly (4) on the fuel injection pump housing. Make sure the lever of the bracket assembly is engaged in the slot of the fuel rack. 4. Install the 1U5426 Compressor Assembly (5) all the way into the 8T9198 Bracket Assembly (4) to compress the spring.
4 Page 19 of Tighten the collet on bracket assembly (4) to hold compressor assembly (5). Spring force now holds the fuel rack against timing pin (3) in the zero position. Fuel Injection Pump Housing (3) 6V4186 Timing Pin. (6) 8T5287 Wrench. (7) 6V7050 Compressor Group. (8) Retainer bushing. 6. Remove the fuel injection line from the pump to be removed and also the fuel injection lines on each side of the pump to be removed. There is spring force on the fuel injection pump plunger and barrel assembly. Removal of retainer bushing (8) without the 6V7050 Compressor Group correctly installed can cause bodily injury. 7. Use 8T5287 Wrench (6) to loosen bushing (8) one quarter turn. Do not remove the bushing at this time. 8. Install 6V7050 Compressor Group (7) on the pump housing over 8T5287 Wrench (6). Lower the screw in the compressor ram to the fuel line seat before the nut is tightened to hold the compressor group in position. This centers the compressor group. Fuel Injection Pump Housing (3) 6V4186 Timing Pin. (6) 8T5287 Wrench. (7) 6V7050 Compressor Group. (8) Retainer bushing. 9. Use 8T5287 Wrench (6) to loosen retainer bushing (8) until it is out of the threads. Slowly raise the compressor tool handle to release the spring force.
5 Page 20 of 126 Fuel Injection Pump Housing (9) 8S2244 Extractor. 10. Remove the 6V7050 Compressor Group and the 8T5287 Wrench. Install 8S2244 Extractor (9) on the injection pump threads. Carefully pull the pump straight up and out of the pump housing bore. Remove the spacer from the pump housing bore. Be careful when an injection pump is disassembled. Do not damage the surface on the plunger. The plunger and barrel are made as a set. Do not put the plunger of one pump in the barrel of another pump. If one part is worn, install a complete new pump assembly. Be careful when the plunger is put into the bore of the barrel. When injection pumps are removed from the fuel injection pump housing, keep the parts together so they can be installed in the same location in the housing. Installation of Fuel Injection Pump NOTICE The fuel rack Must Be In The Center Position before the correct installation of an injection pump is possible. 1. Put the fuel rack in the center position. See Removal of Fuel Injection Pumps for this procedure. Fuel Injection Pump Installation (1) 8S2244 Extractor. (2) Pump barrel. (3) Gear segment. 2. Put 8S2244 Extractor (1) on the threads of the fuel injection pump.
6 Page 21 of Make sure the lifter for the pump to be installed is at the bottom of its travel (cam lobe is at its lowest point). 4. Put the groove in barrel (2) in alignment with the slot (groove) in gear segment (3). 5. Be sure the spacer is in position in the pump housing bore. Fuel Injection Pump Housing (Top View) (4) Pin. (5) Dowel. 6. Carefully install the pump straight down into the pump housing bore. NOTE: The slot (groove) in gear segment (3) must be in alignment with pin (4) in the side of the lifter and the groove in barrel (2) must be in alignment with dowel (5) in the housing bore. Fuel Injection Pump Housing (6) 6V4186 Timing Pin. (7) 8T5287 Wrench. (8) 6V7050 Compressor Group. (9) Retainer bushing. 7. Remove the 8S2244 Extractor. Put the O-ring seal, retainer bushing (9) and 8T5287 Wrench (7) in position on the top of the injection pump. Install 6V7050 Compressor Group (8). 8. Slowly move the handle of the 6V7050 Compressor Group down to push the injection pump into the bore. NOTICE The handle of the 6V7050 Compressor Group must move smoothly down to the lock position. Do not force the handle if it stops. If the handle does not move smoothly down to the lock position, raise the
7 Page 22 of 126 handle, remove the 6V7050 Compressor Group, and repeat Steps 3 through Put the O-ring seal in position in the pump housing bore. Use the 8T5287 Wrench to install the retainer bushing. 10. Remove the 6V7050 Compressor Group. Tighten the retainer bushing to 230 ± 15 N m (170 ± 11 lb ft). NOTICE The bushing must be tightened to the correct torque. Damage to the housing will be the result if the bushing is too tight. If the bushing is not tight enough, the pump will have leakage. 11. Install the fuel injection lines to the pump and tighten to 40 ± 7 N m (30 ± 5 lb ft). See Fuel Injection lines in this section for more information. Be sure the fuel injection line clamps are installed in the correct locations. Incorrectly installed clamps may allow the fuel injection lines to vibrate and become damaged. The damaged lines may leak and cause a fire. The following steps can be used to insure correct installation and operation of any number of individual replacement pumps on most truck engines. 12. Remove or activate the shutoff solenoid if it is installed in the rack actuator housing. NOTE: The manual shutoff override lever can be used to move the shutoff solenoid out of the way so the fuel rack can be moved. NOTE: To check the installation of a replacement pump, it is necessary to have full rack travel in both directions. The actual zero location of the timing pin and rack are not used to check the installation of replacement pumps.
8 Page 23 of 126 Check Fuel Rack Travel (6) 6V4186 Timing Pin. (10) 8T9198 Bracket Assembly. 13. Remove the compressor and bracket assembly (10) from the fuel injection pump housing. Illustration 1. Correct installation in full load position. 14. Raise the timing pin and move the rack to the full load position. Use finger pressure to be sure the rack is at full rack travel (beyond full load position). 15. If the fuel injection pump installation is correct, when the timing pin is lowered it will be on the rack as shown in Illustration 1.
9 Page 24 of 126 Illustration 2. Incorrect installation, full load position restricted by less than full rack travel. 16. If the fuel injection pump installation is not correct, the timing pin position will be approximately 1.91 mm (.075 in) toward the slot for each tooth position out of alignment (see Illustration 2). This will reduce fuel rack travel, even though it may not affect the rack setting, because of additional rack travel at static conditions. Illustration 3. Correct installation at no load (fuel off) position. 17. Raise the timing pin and move the rack to the no load (fuel off) position. 18. If the fuel injection pump installation is correct, when the timing pin is lowered it will be in the timing slot, less than 1.91 mm (.075 in) from the rear face of the slot as shown in Illustration 3.
10 Page 25 of 126 Illustration 4. Incorrect installation, fuel shutoff position restricted by less than full rack travel. 19. If the fuel injection pump installation is not correct, the timing pin position will be more than 1.91 mm (.075 in) from the rear face of the timing slot in the rack (see Illustration 4). 20. When all fuel injection replacement pumps are installed correctly remove 6V4186 Timing Pin (6) from the fuel injection pump housing and install the plug. 21. Install the gasket and cover over the fuel rack on the side of the fuel injection pump housing. NOTICE If one or more of the fuel injection pumps have been installed wrong, it is possible for the engine to run out of control when started. When any of the fuel injection pumps have been removed and installed with the fuel injection pump housing on the engine, take the precautions (steps) that follow to stop the engine if it starts to overspeed (run out of control).
11 Page 26 of 126 Turbocharger Air Inlet Opening a. Remove the air cleaner pipe from the turbocharger leaving the air inlet open as shown. b. Set the governor control at low idle. No pressure applied to the accelerator pedal (up). Be careful when plate is put against air inlet opening. Due to excessive suction, the plate can be pulled quickly against air inlet opening. To avoid crushed fingers, do not put fingers between plate and air inlet opening. c. Start the engine, and if engine starts to overspeed (run out of control), put a steel plate over the air inlet as shown to stop the engine. Stopping the Engine Finding Top Center Compression Position for No. 1 Piston
980 B Wheel Loader S/n 89P1 & Up Volume 1 of 2
Caterpillar Service Manual 980 B Wheel Loader S/n 89P1 & Up Volume 1 of 2 Service Manual THIS IS A MANUAL PRODUCED BY JENSALES INC. WITHOUT THE AUTHORIZATION OF CATERPILLAR OR IT S SUCCESSORS. CATERPILLAR
Woodward PSG Governor
Woodward PSG Governor Linkage Adjustment PSG GOVERNOR CONTROL LINKAGE 1. Rod assembly. 2. Lever. 3. Lever. 1. Make sure levers (2 and 3) are at the SHUTOFF position (fully counterclockwise). 2. With both
ENGINE TUNE-UP INSPECTION OF ENGINE COOLANT INSPECTION OF ENGINE OIL INSPECTION OF BATTERY. INSPECTION OF AIR FILTER (Paper Filter Type)
ENGINE MECHANICAL - Engine Tune-Up EM-17 ENGINE TUNE-UP INSPECTION OF ENGINE COOLANT (See steps 1 and 2 on page CO-4) INSPECTION OF ENGINE OIL (See steps 1 and 2 on page LU-5) INSPECTION OF BATTERY (See
Oregon Fuel Injection
Cummins PT Fuel Pump Diagnostic No Start, with no smoke 1. This could be caused by the fuel pump not turning or a seized gear pump. Remove the fuel supply hose and the fuel inlet fitting from the gear
3304 Engine S/n 43V, 46V, 48V, 78P, 9Z, 7Z & 12Z
Caterpillar Service Manual 3304 Engine S/n 43V, 46V, 48V, 78P, 9Z, 7Z & 12Z Service Manual THIS IS A MANUAL PRODUCED BY JENSALES INC. WITHOUT THE AUTHORIZATION OF CATERPILLAR OR IT S SUCCESSORS. CATERPILLAR
Media Number -SENR Publication Date -01/07/1992 Date Updated -11/10/2001
518 GRAPPLE SKIDDER--SERIES II 95U03200-UP (MACHINE) POWERED BY 330 Page 1 of 16 Model: 518 WHEEL SKIDDER 95U Configuration: 518 GRAPPLE SKIDDER--SERIES II 95U03200-UP (MACHINE) POWERED BY 3304 ENGINE
Media Number -SENR Publication Date -01/10/1977 Date Updated -12/10/2001
- - 55, 56, 57, 58 & 59 TOWING WINCHES Page 1 of 21 Testing and Adjusting 55, 56, 57, 58 & 59 TOWING WINCHES Media Number -SENR7217-01 Publication Date -01/10/1977 Date Updated -12/10/2001 Testing And
Copper Sleeve, Unit Injector, Replacement
Volvo Trucks North America Greensboro, NC USA This service bulletin replaces SB 237-46, Copper Sleeve, Unit Injector, Replacement dated 6.2007, publication no. PV776-20177417. DService Bulletin Trucks
951B Traxcavator S/n 79H, 32F, 69H & 86J Volume 1 of 2
Caterpillar Service Manual 91B Traxcavator S/n 79H, 2F, 9H & 8J Volume 1 of 2 Service Manual THIS IS A MANUAL PRODUCED BY JENSALES INC. WITHOUT THE AUTHORIZATION OF CATERPILLAR OR IT S SUCCESSORS. CATERPILLAR
3306 Diesel Engine S/n 8Z, 10Z, & 13Z
Caterpillar Service Manual 3306 Diesel Engine S/n 8Z, 10Z, & 13Z Service Manual THIS IS A MANUAL PRODUCED BY JENSALES INC. WITHOUT THE AUTHORIZATION OF CATERPILLAR OR IT S SUCCESSORS. CATERPILLAR AND IT
Disassembly and Assembly
SENR9973-01 September 2007 Disassembly and Assembly 400C Industrial Engine HB (Engine) HD (Engine) HH (Engine) HL (Engine) HM (Engine) HN (Engine) HP (Engine) HR (Engine) Important Safety Information Most
Troubleshooting the Transmission Hydraulic System
Testing and Adjusting IT28F INTEGRATED TOOLCARRIER POWER TRAIN Testing And Adjusting Introduction Reference: For Specifications with illustrations, refer to SENR5974, IT28F Integrated Toolcarrier Power
Disassembly and Assembly
K EN R 623 2-00 August 2006 Disassembly and Assembly 2506-15 Industrial Engine M G A (Engine) MGB (Engine) M G D (Engine) Important Safety Information Most accidents that involve product operation, maintenance
Static Injection Timing
Page 1 of 13 006-025 Static Injection Timing General Information The static timing is relative to the amount of push tube travel remaining when the piston is 5.161 mm [0.2032 in], or 19 degrees before
Maintenance Information
80234313 Edition 1 June 2006 Air Grinder, Die Grinder, Sander and Belt Sander Series G1 (Angle) Maintenance Information Save These Instructions WARNING Always wear eye protection when operating or performing
955L Traxcavator S/n 64J, 71J & 85J Volume 1 of 2
Caterpillar Service Manual 955L Traxcavator S/n 64J, 71J & 85J Volume 1 of 2 Service Manual THIS IS A MANUAL PRODUCED BY JENSALES INC. WITHOUT THE AUTHORIZATION OF CATERPILLAR OR IT S SUCCESSORS. CATERPILLAR
AUTOMATIC CLUTCH Models
AUTOMATIC CLUTCH 1940 Models Source of this material is from 1940 Series, Issue 4, January 1940 Hudson Service Magazine AUTOMATIC CLUTCH 1940 MODELS The automatic clutch installation and adjustment procedure
MANUAL TRANSAXLE Return to Main Table of Contents
MANUAL TRANSAXLE Return to Main Table of Contents GENERAL... 2 MANUAL TRANSAXLE CONTROL... 12 SHIFT LEVER ASSEMBLY... 14 MANUAL TRANSAXLE... 15 MANUAL TRANSAXLE ASSEMBLY... 17 FIFTH SPEED SYNCHRONIZER
Maintenance Information
04581245 Edition 2 May 2014 Air Grinder, Die Grinder and Sander Series G2 (Angle) Maintenance Information Save These Instructions Product Safety Information WARNING Failure to observe the following warnings,
GH-BETTIS OPERATING & MAINTENANCE INSTRUCTIONS DISASSEMBLY & ASSEMBLY FOR THE T80X-M4-S DOUBLE ACTING SERIES HYDRAULIC ACTUATORS
GH-BETTIS OPERATING & MAINTENANCE INSTRUCTIONS DISASSEMBLY & ASSEMBLY FOR THE T80X-M4-S DOUBLE ACTING SERIES HYDRAULIC ACTUATORS -S INDICATES CYLINDERS ARE IN TANDEM PART NUMBER: 100121 REVISION "A" ECN
Installation Manual. Model T680A/B Engine Brakes. For Mack 6 Cylinder, 4 Valve Head E6 and E7 Series Engines. Engine Brakes
Engine Brakes Installation Manual Model T680A/B Engine Brakes For Mack 6 Cylinder, 4 Valve Head E6 and E7 Series Engines TecBrake P.O. Box 27822 Houston, Texas 77227 INSTALLATION MANUAL TECBRAKE T680A
TURBOCHARGER Toyota Celica DESCRIPTION OPERATION TURBOCHARGING SYSTEMS All Models
TURBOCHARGER 1988 Toyota Celica 1988 TURBOCHARGING SYSTEMS All Models DESCRIPTION Most models use a water-cooled turbocharger, mounted directly to the exhaust manifold with a wastegate assembly attached
CAUTION. Fuel Injection Pump, In-Line, Spill Port Timing
Page 4 of 22 Rotate the crankshaft counterclockwise, as viewed from the front of the engine, to approximately 40 degrees before TDC. Both the RQV and RQV-K governor require the shutdown lever to be in
Section 10 Chapter 17
Section 10 Chapter 17 24 Valve, 8.3 Liter Engine Air Intake System Note: All coding used in the 8.3 Liter and 9 Liter engine manuals are Cummins engine codes. These engine codes have no meaning to New
Installation Manual. Model T675A Engine Brakes. For Mack 6 Cylinder, 2 valve Head ENDT-673, 675, 676 & E6 Series Engines.
Engine Brakes Installation Manual Model T675A Engine Brakes For Mack 6 Cylinder, 2 valve Head ENDT-673, 675, 676 & E6 Series Engines TecBrake P.O. Box 27822 Houston, Texas 77227 INSTALLATION MANUAL TECBRAKE
NUMBER: S.M. REF.: Listed in Table 1 ENGINE: DD13 DATE: July 2009
NUMBER: 7 10 09 S.M. REF.: Listed in Table 1 ENGINE: DD13 DATE: July 2009 SUBJECT: CAMSHAFT AND ROCKER SHAFT ASSEMBLIES ADDITIONS, REVISIONS, OR UPDATES Publication Number Platform Section Title Change
Module 13: Mechanical Fuel Injection Diagnosis and Repair
Terms and Definitions Parts of Injection Nozzles Types of Nozzle Valves Operation of an Injection Nozzle Fuel Flow Through the Unit Injector Optional Features on Fuel Injection Pumps Main Parts of a Distributor-Type
Vickers. Overhaul Manual. Vane Pumps. Small and Large Series Combination Pumps VC(K)(S)-**-(*)*D*-6(1) VC(K)(S)-**-(*)-*-*D*-5(1)
Overhaul Manual Vickers Vane Pumps Small and Large Series Combination Pumps VC(K)(S)-**-(*)*D*-6(1) VC(K)(S)-**-(*)-*-*D*-5(1) Revised 12/1/86 I-3150-S Table of Contents Section I. Introduction................................................................................
General Safety and Maintenance Manual. Bore and Stroke. Throttle Type. Blows per Minute. (L) Lever Inches (564 mm)
HENRY TOOLS Industrial Airtools at Work General Safety and Maintenance Manual Bench Rammer and Floor Rammers Model Number Bore and Stroke 1.0 Inch x 4.0 Inch (25 mm x 102 mm) Throttle Type Blows per Minute
Remove Air Cleaner Cover and. Filter
Remove Air Cleaner Cover and Inspect paper filter for tears Foam pre-cleaner is washable if equipped Replace if necessary Filter Remove Trim Panel Pull throttle lever knob off Remove 3, 8mm screws Remove
955L Traxcavator S/N 8Y1, 13X1, & 57M1 Volume 1 of 3
Caterpillar Service Manual 955L Traxcavator S/N 8Y1, 13X1, & 57M1 Volume 1 of 3 Service Manual THIS IS A MANUAL PRODUCED BY JENSALES INC. WITHOUT THE AUTHORIZATION OF CATERPILLAR OR IT S SUCCESSORS. CATERPILLAR
AUTOMATIC TRANSMISSIONS Mitsubishi F3A20 Series TRANSMISSION APPLICATION TABLE
Article Text ARTICLE BEGINNING AUTOMATIC TRANSMISSIONS Mitsubishi F3A20 Series APPLICATION TRANSMISSION APPLICATION TABLE Vehicle Application Transmission Model Colt 3-Speed (1990-94)... F3A21 Colt Vista
MGA Twin Cam Engine Assembly.
MGA Twin Cam Engine Assembly. The following article is a collection of notes of things to be observed in the assembling of MGA Twin Cam engines. To be read in conjunction with the Workshop Manual. It does
POWER STEERING TO INDEX POWER STEERING SYSTEM PRECAUTIONS... OPERATION CHECK... PROBLEM SYMPTOMS TABLE... VANE PUMP ASSEMBLY COMPONENTS...
TO INDEX STEERING POWER STEERING POWER STEERING SYSTEM PRECAUTIONS.............................................. OPERATION CHECK......................................... PROBLEM SYMPTOMS TABLE.................................
DeZURIK R1 AND R2 POWERRAC ACTUATORS
R1 AND R2 POWERRAC ACTUATORS Instruction D10268 July 2016 Instructions These instructions provide installation, operation, and maintenance information for R1 AND R2 POWERRAC Actuators. They include procedures
MAINTENANCE MANUAL FOR THERMOSTATIC TEMPERATURE REGULATING VALVE TRAC STYLE P
MANUAL NUMBER P-EFS-1 MAINTENANCE MANUAL FOR THERMOSTATIC TEMPERATURE REGULATING VALVE TRAC STYLE P TRAC Regulator Company Inc. 160 South Terrace Avenue Mount Vernon, New York USA 10550-2408 Phone: (914)
941 Traxcavator S/n 16U, 70H, 80H & up
Caterpillar Service Manual 941 Traxcavator S/n 16U, 70H, 80H & up Service Manual THIS IS A MANUAL PRODUCED BY JENSALES INC. WITHOUT THE AUTHORIZATION OF CATERPILLAR OR IT S SUCCESSORS. CATERPILLAR AND
Engine Power Output Low
File: 3666087-t057-tr Page 1 of 5 STEP 1 Engine under excessive load STEP 2 Fuel shutoff lever (mechanical) partially engaged STEP 3 Engine will not reach full throttle STEP 4 Poor fuel quality or wrong
CARBURETION. Carburetor Identification. Models , , , , , , , , , , ,
Carburetor Identification Models 110400, 110600, 111400, 111600, 113400, 120400, 120600, 121400, 121600, 122600, 123400, 123600 Models 28S700, 311700 Service Carburetor Briggs & Stratton/Walbro LMS Models
DeZURIK R1 POWERRAC ACTUATOR ON 1/2-3" PEC ECCENTRIC VALVES
R1 POWERRAC ACTUATOR ON 1/2-3" PEC ECCENTRIC VALVES Instruction D10381 August 2012 Instructions These instructions provide information about the R1 PowerRac actuator. They are for use by personnel who
OPERATION AND PARTS MANUAL
OPERATION AND PARTS MANUAL MODEL NUMBER : PART NUMBER : GTL 1110 1900-0510 SERIAL NUMBER : BAYNE MACHINE WORKS, INC. PHONE: (864) 288-3877 910 FORK SHOALS ROAD TOLL FREE: (800) 535-2671 GREENVILLE S.C.,
TECHNICAL MANUAL OPERATOR S, UNIT, INTERMEDIATE (DS) AND INTERMEDIATE (GS) MAINTENANCE MANUAL FOR
TM 5-2815-232-14 TECHNICAL MANUAL OPERATOR S, UNIT, INTERMEDIATE (DS) AND INTERMEDIATE (GS) MAINTENANCE MANUAL FOR ENGINE, DIESEL, CATERPILLAR, MODEL 3508 NSN 2815-01-216-0938 HEADQUARTERS, DEPARTMENT
Maintenance Information
80234313 Edition 2 May 2014 Air Grinder, Die Grinder, Sander and Belt Sander Series G1 (Angle) Maintenance Information Save These Instructions Product Safety Information WARNING Failure to observe the
ASSEMBLY. Transmission Automatic Transaxle/Transmission. Special Tool(s) Alignment Set, Fluid Pump 307-S039 (T74P X) Special Tool(s)
307-01-1 Automatic Transaxle/Transmission 307-01-1 ASSEMBLY Transmission Special Tool(s) Adjustment Set, Transmission Band 307-S022 (T71P-77370-A) Special Tool(s) Alignment Set, Fluid Pump 307-S039 (T74P-77103-X)
2002 F-Super Duty /Excursion Workshop Manual
Page 1 of 25 SECTION 307-01: Automatic Transaxle/Transmission 2002 F-Super Duty 250-550/Excursion Workshop Manual ASSEMBLY Procedure revision date: 05/23/2001 Transmission Special Tool(s) Remover, O-Ring
Timing Chain: Service and Repair With 2 Piece Tensioner (TSB A) Precaution. Removal This article has been updated with bulletin No A.
1997 Chevrolet Cavalier L4-144 2.4L DOHC VIN T SFI Page 1 Timing Chain: Service and Repair With 2 Piece Tensioner (TSB 67-61-22A) Precaution Bulletin No.: 67-61-22A Date: July, 1998 TIMING CHAIN TENSIONER
D5B & D5E Crawlers S/n 22X1, 23X1,24X1, 25X1, 43X1, 44X1, 45X1, 46X1, 47X1, 48X1 & 49X1 & up Volume 1 of 3
Caterpillar Service Manual D5B & D5E Crawlers S/n 22X1, 23X1,24X1, 25X1, 43X1, 44X1, 45X1, 46X1, 47X1, 48X1 & 49X1 & up Volume 1 of 3 Service Manual THIS IS A MANUAL PRODUCED BY JENSALES INC. WITHOUT THE
2012 Honda Crosstour EX ENGINE Cylinder Head - (4-CYL)
Fig. 4: Identifying Cylinder Head Components Location (3 Of 3) ENGINE COMPRESSION INSPECTION NOTE: After this inspection, you must reset the PCM. Otherwise, the PCM will continue to stop the fuel injectors
OPERATION AND PARTS MANUAL
OPERATION AND PARTS MANUAL MODEL NUMBER : PART NUMBER : GRL 1110 1900-0540 SERIAL NUMBER : BAYNE MACHINE WORKS, INC. PHONE: 864.288.3877 910 FORK SHOALS ROAD TOLL FREE: 800.535.2671 GREENVILLE SC, 29605
5. FUEL SYSTEM 5-0 FUEL SYSTEM UXV 500
5 FUEL SYSTEM 5 SERVICE INFORMATION------------------------------------------------ 5-02 TROUBLESHOOTING----------------------------------------------------- 5-03 FUEL TANK -----------------------------------------------------------------
BLACKMER PISTON AIR VALVE SAFETY DATA. For Piston Air Valve Style AVC and Discontinued Style AVB TABLE OF CONTENTS SAFETY DATA...
BLACKMER PISTON AIR VALVE 960333 INSTALLATION OPERATION AND MAINTENANCE INSTRUCTIONS WITH PARTS LIST For Piston Air Valve Style AVC and Discontinued Style AVB Page 1 of 8 Section Effective Replaces INSTRUCTIONS
Maintenance Information
Form 16573321 Edition 1 July 2004 Air Grinder Series 61H Maintenance Information Save These Instructions Always wear eye protection when operating or performing maintenance on this tool. Always turn off
Engine [P-TB216EBA] 3TNV74F-SPTB
![Engine [P-TB216EBA] 3TNV74F-SPTB](/thumbs/76/73516114.jpg "Engine [P-TB216EBA] 3TNV74F-SPTB")
Ref. 0-1 Page 0-1 How to read this Parts Catalog Part No. ENGINE 3TNV74F-SPTB 2013.7.15 P-TB216EBA Ref. 0-1 Page 0-1 Ref. 0-2 Page 0-2 CYLINDER BLOCK 26 27 5 4 12 6 4 10 4 13 11 1 23 34 23 34 7 7 7 7 28
D6 & D6C Crawlers S/n 74A1, 76A1, 41A1, 71A1, 73A1, 82A1 & 96A1 & up
Caterpillar Service Manual D6 & D6C Crawlers S/n 74A, 76A, 4A, 7A, 73A, 82A & 96A & up Service Manual THIS IS A MANUAL PRODUCED BY JENSALES INC. WITHOUT THE AUTHORIZATION OF CATERPILLAR OR IT S SUCCESSORS.
INSTRUCTION MANUAL INTERNAL GEAR PUMP TITAN G-4124A SERIES=> FLANGED TITAN G-124A SERIES => FLANGED MODELS:
INSTRUCTION MANUAL INTERNAL GEAR PUMP TITAN G-4124A SERIES=> FLANGED TITAN G-124A SERIES => FLANGED MODELS: G-H, G-HL, G-K, G-KK, G-L, G-LQ, G-LL, GLS, G-Q, G-QS 1 Contents Maintenance Thrust bearing adjustment
Page 1 of 75 303-01D Engine - 5.2L 32V Ti-VCT 2016 Mustang Assembly Procedure revision date: 12/15/2016 Special Tool(s) / General Equipment Engine Base Part Number: 6L084 205-142 (T80T-4000-J) Installer,
I & M Mark 78 Series. Ideal Installation. Start-Up. Installation & Maintenance Instructions for Mark 78 Control Valves (1-1/2-2 )
I & M Mark 8 Series 0 Wasson Road Cincinnati, OH 4509 USA Phone 5-5-5600 Fax 5-8-005 info@richardsind.com www.jordanvalve.com Installation & Maintenance Instructions for Mark 8 Control Valves (-/ - ) Warning:
Troubleshooting, Service Tips, And Major Improvements For Hydrostatic Transmissions (Special Edition){3200}
Page 1 of 75 Troubleshooting, Service Tips, And Major Improvements For Hydrostatic Transmissions (Special Edition){3200} 943, 953, 963, 973 Loaders Introduction The hydrostatic transmissions used in 943,
WEBER CARBURETOR TROUBLESHOOTING GUIDE
This guide is to help pinpoint problems by diagnosing engine symptoms associated with specific vehicle operating conditions. The chart will guide you step by step to help correct these problems. For successful
I & M Mark 78 Series. Ideal Installation. Start-Up. Installation & Maintenance Instructions for Mark 78 Control Valves (1/2-1 )
I & M Mark 8 Series 30 Wasson Road Cincinnati, OH 4509 USA Phone 53-533-5600 Fax 53-8-005 info@richardsind.com www.jordanvalve.com Installation & Maintenance Instructions for Mark 8 Control Valves (/ -
MAINTENANCE INSTRUCTIONS
MAINTENANCE INSTRUCTIONS Direct Mount Pneumatic Actuators Double-Acting and Spring-Return Installation, Service and Operation Sizes 0052 through 0125 COMPONENT LIST Item Description 1 Housing 2 Pinion
DIPACO CATERPILLAR NEW SCROLL PARTS CATALOG 3304B/3306B AND 3406B/3406C. Updated April April CATERPILLAR NEW SCROLL
DIPACO 3304B/3306B AND 3406B/3406C PARTS CATALOG Updated April 2010 April 2010 1 INTRODUCTION ADDRESS DIPACO, Inc. 105 East Parr Boulevard Reno, Nevada 89512 USA Phone: (775) 329-7511 Fax: (775 329-9740
BRAKES. Section III REAR AXLE DATA AND SPECIFICATIONS HAND BRAKE CHRYSLER SERVICE MANUAL BRAKES 17
BRAKES 17 There is no basic design change in the rear axle and sure grip differential except the larger diameter pinion shaft is now used on all models for 1959. The Service Procedures will remain the
Systems Operation Testing and Adjusting
M0064276 (en-us) December 2015 Systems Operation Testing and Adjusting 4008-30 Industrial Engine SD8 (Engine) Important Safety Information Most accidents that involve product operation, maintenance and
Maintenance Information
16573321 Edition 3 February 2014 Air Grinder Series 61H Maintenance Information Save These Instructions Product Safety Information WARNING Failure to observe the following warnings, and to avoid these
DRIVE AXLE Volvo 960 DESCRIPTION & OPERATION AXLE IDENTIFICATION DRIVE AXLES Volvo Differentials & Axle Shafts
DRIVE AXLE 1994 Volvo 960 1994 DRIVE AXLES Volvo Differentials & Axle Shafts 960 DESCRIPTION & OPERATION All 960 station wagon models use type 1041 rear axle assembly. All 960 4-door models use type 1045
CRANKSHAFT & MAIN BEARINGS
CRANKSHAFT & MAIN BEARINGS * PLEASE READ THIS FIRST * REMOVAL Ensure all main bearing caps are marked for location on cylinder block. Some main bearing caps have an arrow stamped on them. The arrow must
MODEL NUMBER AND IDENTIFICATION. Pag. 5 CHARACTERISTICS CHARACTERISTIC POWER, TORQUE AND SPECIFIC CONSUMPTION CURVES
MODEL NUMBER AND IDENTIFICATION CHARACTERISTICS CHARACTERISTIC POWER, TORQUE AND SPECIFIC CONSUMPTION CURVES MAINTENANCE - RECOMMENDED OIL TYPE - REFILLING POSSIBLE CAUSES AND TROUBLE SHOOTING OVERALL
Accumulator Charging Valve (Brake) - Test and Adjust
Testing and Adjusting 966G Series II Wheel Loader and 972G Series II Wheel Loader Braking System Accumulator Charging Valve (Brake) - Test and Adjust Table 1 Required Tools Part Number Description 1U-5481
A-PDF Split DEMO : Purchase from to remove the watermark
5-18 FUEL AND LUBRICATION SYSTEM A-PDF Split DEMO : Purchase from www.a-pdf.com to remove the watermark Use a % size drill bit with a drill-stop to remove the pilot screw plug. Set the drill-stop 6 mm
Oregon Fuel Injection
Removal Inline Pump Removal and Installation Cummins engine with lock timed inline injection pump 1. Clean the exterior of the injection pump and mounting surfaces. 2. Remove the fuel supply line and return
Section 10 Chapter 7
Section 10 Chapter 7 24 Valve, 8.3 Liter Engine Troubleshooting Symptoms Identification Note: All coding used in the 8.3 Liter and 9 Liter engine manuals are Cummins engine codes. These engine codes have
CARTER DOWNDRAFT CARBURETOR Terraplane All Models. Technical Information
CARTER DOWNDRAFT CARBURETOR 1934 Terraplane All Models Technical Information . Carter W-1 Downdraft Carburetors 1934 Terraplane Challenger, Model KS NOTE: Terraplane Models. Carburetor fitted with Anti-
MAINTENANCE MANUAL DI 16
MAINTENANCE MANUAL DI 16 0.2-1.6% Press Ctrl + L for full screen 1 STANDARD INSTALLATION Inlet Outlet Optional accessories: Pressure regulator Solenoid valves Water meter Flow restrictor 200 Mesh/ 80 micron
Bthird, or power stroke by the expanding gases. As the
third, or power stroke by the expanding gases. As the piston reaches DC it enters the fourth cycle. The exhaust valve opens and the piston rises forcing burned gases from the combustion chamber in what
Maintenance Information
45761848 Edition 3 February 2014 Air Die Grinder AC4A, SC4A and XC4A Series Maintenance Information Save These Instructions Product Safety Information WARNING Failure to observe the following warnings,
HYDRAULICS. TX420 & & lower. Hydraulic Tandem Pump Removal. 4. Remove the LH side panel (Fig. 0388).
TX420 & 425 240000299 & lower 4. Remove the LH side panel (Fig. 0388). Hydraulic Tandem Pump Removal Note: Cleanliness is a key factor in a successful repair of any hydraulic system. Thoroughly clean all
SD Bendix DD-3 & SD-3 Safety Actuators PUSH PLATE & SHAFT ASSY. LOCKPORT SERVICE DIAPHRAGM SEPARATOR LOCKING PISTON O-RING LOCKING PISTON
SD-02-4600 Bendix DD-3 & SD-3 Safety Actuators AUXILIARY DIAPHRAGM SERVICE DIAPHRAGM SEPARATOR PUSH PLATE & SHAFT ASSY. LOCKING PISTON O-RING LOCKING PISTON LOCKPORT DRAIN SLOT RETURN SPRING CAP O-RING
BOSCH VE 250 INJECTION PUMP
1.0 BOSCH VE 250 DIESEL INJECTION PUMP Land Rover fit the Bosch VE-type rotary distributor diesel injection pump onto their 300 TDI engines. Two main variants were installed: the standard models were fit
5. FUEL SYSTEM 5-0 FUEL SYSTEM MXU 250R/300R
5 FUEL SYSTEM 5 SERVICE INFORMATION------------------------------------------------ 5-2 TROUBLESHOOTING----------------------------------------------------- 5-3 FUEL TANK -----------------------------------------------------------------
HI-FLOW FUEL RAIL. Installation Instructions for: Part Numbers , ,
HI-FLOW FUEL RAIL Installation Instructions for: Part Numbers 25-100, 25-103, 25-112 ADVANCED ENGINE MANAGEMENT INC. 2205 126 TH Street, Unit A Hawthorne, CA. 90250 Phone: (310) 484-2322 Fax: (310) 484-0152
GH-BETTIS SERVICE INSTRUCTIONS DISASSEMBLY & REASSEMBLY FOR MODELS HD521-M4, HD721-M4 AND HD731-M4 DOUBLE ACTING SERIES PNEUMATIC ACTUATORS
GH-BETTIS SERVICE INSTRUCTIONS DISASSEMBLY & REASSEMBLY FOR MODELS HD521-M4, HD721-M4 AND HD731-M4 DOUBLE ACTING SERIES PNEUMATIC ACTUATORS WITH HYDRAULIC CONTROL PACKAGE PART NUMBER: SE-023 REVISION:
Fisher 657 Diaphragm Actuator Sizes and 87
Instruction Manual 657 Actuator (30-70 and 87) Fisher 657 Diaphragm Actuator Sizes 30 70 and 87 Contents Introduction... 1 Scope of Manual... 1 Description... 2 Specifications... 2 Installation... 3 Mounting
Construction. Figure The Stanadyne DB4 injection pump uses four opposed plungers. Components.
Construction. The Stanadyne pump, shown in Figure 5-62 incorporates four pumping plungers. The driveshaft engages the distributor rotor in the hydraulic head. The rotor holds the four pumping plungers.
ENGINE ADJUSTMENTS. Remote Controls
ENGINE ADJUSTMENTS Remote Control Wire Travel The remote control wire should measure 2.25 (54 mm) when extended outside the casing (Figure 2). After installation, the travel of the remote control wire
510 & 515 Front End Loader
International Harvester Service Manual 510 & 515 Front End Loader Service Manual THIS IS A MANUAL PRODUCED BY JENSALES INC. WITHOUT THE AUTHORIZATION OF INTERNATIONAL HARVESTER OR IT S SUCCESSORS. INTERNATIONAL
Standard Valves Series Globe Valves Series Angle Valves Series Way-Valves
Installation, Operation, Maintenance Instructions Standard Valves Series 035 000 Globe Valves Series 031 000 Angle Valves Series 033 000 3-Way-Valves 1 GENERAL INFORMATION These instructions are designed
DIESEL FUEL Click on the applicable bookmark to selected the required model year
DIESEL FUEL 13E-2 DIESEL FUEL General Information/Service Specifications/ Special Tool/On-vehicle Service GENERAL INFORMATION 13300010025 The fuel is drawn out of the fuel tank by means of the feed pump
Installation Manual. For ISC, ISL, ISC03 And ISL03 Engines
Installation Manual For ISC, ISL, ISC03 And ISL03 Engines Table of Contents 1. Installation of the E Brake Assembly... 3 2. Pneumatic Group Installation... 5 3. Installation of the Controls... 7 4. Final
ASSEMBLY. Transmission Automatic Transmission 5R44E and 5R55E. Special Tool(s)
307-01-1 Automatic Transmission 5R44E and 5R55E 307-01-1 ASSEMBLY Transmission Special Tool(s) Holding Fixture, Transmission 307-262 (T93T-77002-AH) Special Tool(s) Installer, Transmission Extension Housing
Disassembly / Reassembly Procedure
08-T059 Disassembly / Reassembly Procedure HEAVY DUTY TYPE PNEUMATIC CYLINDER 10A-3 SERIES Failure to observe the instructions given in this manual could cause this equipment
This file is available for free download at
This file is available for free download at http://www.iluvmyrx7.com This file is fully text-searchable select Edit and Find and type in what you re looking for. This file is intended more for online viewing
Troubleshooting The Transmission Hydraulic System
416B, 426B, 428B, 436B, & 438B BACKHOE LOADERS TRANSMISSION Testing And Adjusting Troubleshooting The Transmission Hydraulic System Make reference to the following warning and pressure tap locations for
SD Bendix E-10PR Retarder Control Brake Valve DESCRIPTION. OPERATION - Refer to Figure 2
SD-03-832 Bendix E-10PR Retarder Control Brake Valve MOUNTING PLATE SUPPLY 4 PORTS ELECTRICAL AUXILIARY DESCRIPTION TREADLE RETARDER CONTROL SECTION EXHAUST DELIVERY 4 PORTS FIGURE 1 - E-10PR RETARDER
Installation Instructions & Information
VP44 Installation Instructions & Information VP44 Pump General Information The fuel injection pump (VP44) is an electronic rotary distributor pump. The pump performs four basic functions: 1. 2. 3. 4. Producing
DP3 Pump. 3:1, Air-operated, Oil. General. Operation. Technical Data. Installation R0 10/09. 35a 35b 35c
DP3 Pump 3:1, Air-operated, Oil General The DP3 Pump is a compressed air-operated piston reciprocating medium pressure pump. Suitable for medium flow transfer of high viscosity lubricants and for oil delivery
CARBURETOR - HITACHI 2-BBL
CARBURETOR - HITACHI 2-BBL 1986 Isuzu Trooper II 1986 Hitachi Carburetors HITACHI DCH340, DCR384, DFP340, DFP384 & DHP340 2-BARREL P UP & Trooper II DESCRIPTION Carburetor is a 2-barrel downdraft type
SPECIFICATIONS TEST AND ADJUSTMENT SPECIFICATIONS SPECIFICATIONS ENGINE FD620D, K SERIES
ENGINE FD620D, K SERIES SPECIFICATIONS SPECIFICATIONS TEST AND ADJUSTMENT SPECIFICATIONS Engine Oil Pressure Sensor Activates............................... 98 kpa (14.2 psi) Oil Pressure While Cranking
EM 6 VALVE CLEARANCE ENGINE MECHANICAL EM11I 01 ADJUSTMENT HINT:
EM6 ADJUSTMENT EM11I01 Inspect and adjust the valve clearance when the engine is cold. 1. REMOVE NO.1 ENGINE UNDER COVER 2. DRAIN ENGINE COOLANT 3. REMOVE AIR CLEANER INLET 4. REMOVE AIR CLEANER ASSEMBLY
John Deere. MODEL: 4320 Tractor JD-S-TM1029
John Deere MODEL: 4320 Tractor THIS IS A MANUAL PRODUCED BY JENSALES INC. WITHOUT THE AUTHORIZATION OF JOHN DEERE OR IT'S SUCCESSORS. JOHN DEERE AND IT'S SUCCESSORS ARE NOT RESPONSIBLE FOR THE QUALITY