Quolis Series. Quolis 5000 Chair IMPORTANT

Size: px

Start display at page:

Download "Quolis Series. Quolis 5000 Chair IMPORTANT"

Ethel Anderson
6 years ago
Views:

1 Quolis Series Quolis 000 Chair Model Q-000 INSTALLATION INSTRUCTIONS IMPORTANT This manual provides installation instructions for the Quolis Chair. The instructions contained in this booklet should be thoroughly read and understood before operating the chair. After the installation has been completed, keep this manual in a safe place and refer to it for future maintenance. R

3 Intended Use of the Product This product is intended for the exclusive use for diagnoses, treatments and relative procedures of dentistry, and must be operated or handled by the qualified dentists or by dental staffs under the supervision of the dentist. Such dentists or dental staffs should instruct and/or assist the patients to approach to and leave from the product. Patients should not be allowed to operate or handle the product unless he/she is so instructed. Classification a. Protection against electric shock : Class I Equipment, Type B Applied Parts b. Protection against water ingress : Ordinary equipment (IPX0) c. Equipment not suitable for use in the presence of a flammable anesthetic mixture with air or with oxygen or nitrous oxide. -i-

4 . OVERVIEW AND MAJOR CONPONENTS 9 0 Fig.- Overview Headrest Backrest Sling Armrest Seat Armrest Bracket Main Link Cover Sub Link Cover 9 Pump Cover 0 Base Main Switch Panel Electrical Plug Headrest Assembly Headrest Cover Backrest Cover Back Support Flange Touchpad Control Panel 0 Safety Seat Lift Backrest Swivel Lock Release Backrest Recline Seat Lower 0 Auto Return Preset- Preset- Preset- Left Side Right Side Fig.- Touchpad Control Panel --

5 --. DIMENSIONS AND SPECIFICATIONS -. Dimensions -inch- -/ -/ / 9 -/ -/ -/ / 9-/ / -/ -/ -/ -/ -/ -/ -/ -/ -/ -/ -/ 9-/ Fig.- Dimensions

6 . INTRODUCTION -. Precautions For Installation - The floor construction required to safely support the chair and delivery system is 0 lbs./ft (00kg/m ) at minimum. - During lifting and unpacking of the chair, make sure to hold only the designated parts. - Do not drop or hit the chair. - After the chair is unloaded from the palette and placed at the desired location, please make sure to remove the shipping bolt with the red tag. Damage to chair may occur if shipping bolt is not removed prior to chair operation. - Do not connect to power supply other than 0V 0HZ. - Ground chair properly prior to turning power on. - Chair base must be anchored to the floor for maximum stability. - Refer to the installation manual of the chair and dental unit (if it is to be used) prior to, and during installation. - When the installation process has been completed, verify that all the mechanical and electrical functions are working properly and that there is no evidence of oil leakage. -. Required Tools The following tools are necessary for installation of the chair: - Philips screw drivers (No., No.) - Flat screw driver - Wrenches (open end): mm, 0mm, mm - Hex key wrenches:.mm, mm, mm - Socket wrench with ratchet drive mm --

7 . UNPACKING OF CHAIR The chair packaging consists of two boxes: Box : Chair base section Box : Upholstery section After unpacking, make sure all components can be located.! CAUTION Knives or sharp objects may damage package contents. Open with care! Fig. - Fig. - Fig Fig. - --

. INSTALLATION -. Positioning The Chair Armrest Bracket Lifting Bar!

. Remove the Chair Base Section from the pallet by holding the Armrest Bracket and Lifting Bar and place it at the planned

. Plug chair into a 0V AC outlet. Shipping Bolt. Turn the Main Power Switch on and raise the chair up. (Fig.

. Remove the pump cover by removing two slotted screws (Mx0mm) from each side of the pump cover. (Fig.-).

8 . INSTALLATION -. Positioning The Chair Armrest Bracket Lifting Bar! CAUTION Do not connect in the power supply line before removing the red tagged Shipping Bolt.. Remove the Chair Base Section from the pallet by holding the Armrest Bracket and Lifting Bar and place it at the planned location. (Fig. -). Remove the red tagged Shipping Bolt (M0x0mm) from the chair. (Fig. -) Pallet Fig. -! CAUTION Do not lift the chair by the upper structure after removal of the red tagged Shipping Bolt.. Plug chair into a 0V AC outlet. Shipping Bolt. Turn the Main Power Switch on and raise the chair up. (Fig. -) Note: Refer to the Operation Manual for chair to operate.. Remove the pump cover by removing two slotted screws (Mx0mm) from each side of the pump cover. (Fig.-).Remove the red tagged Oil Plug from the Oil Reservoir. (Fig.-) Fig. -. Remove the Lifting Bar from the chair by removing two M0x0mm bolts. (Fig.-) Pump Cover Lifting Bar Tagged Oil Plug Electrical Plug Main Power Switch Slotted Screw (Mx0mm) Oil Reservoir Fig. - Fig. - --

-. Attaching The Chair Base To The Floor Attach the chair base to the floor using the two anchor bolts (9xmm). (Fig.-, -)!

(if it is to be installed on chair) anchoring holes Fig. - Fig.

for the dental unit before proceeding further with chair installation.

If you don t use a Junction box, plug the hole by a pump cover cap. Fix this cover by x 0mm screw. (Fig.

9 -. Attaching The Chair Base To The Floor Attach the chair base to the floor using the two anchor bolts (9xmm). (Fig.-, -)! CAUTION Attach the chair base to the floor prior to installation of the Quolis dental unit. (if it is to be installed on chair) anchoring holes Fig. - Fig. - Anchor Bolt (9xmm) IMPORTANT: If you are going to the install Quolis dental unit onto the chair, please refer to the installation manual for the dental unit before proceeding further with chair installation. Resume assembly of the chair after installation of the dental unit onto the chair has been completed. If you don t use a Junction box, plug the hole by a pump cover cap. Fix this cover by x 0mm screw. (Fig.-) Attach the Pump Cover to the chair using the two slotted screws (Mx0mm). (Fig.-) Note: Please tighten these screws firmly by a Flat screw driver so that no other personnel than qualified technicians can open the cover. Insert the plastic cap into the hole on the Main Link Cover. (Fig.-) Pump Cover Plastic Cap Main Link Cover Pump Cover Pump Cover Cap Pan Head Phillips Wood Screw (x0mm) Fig. - Fig. - Slotted Screw (Mx0mm) --

Attach the backrest cushion to the backrest assembly as follows (Fig.

10 -. Attaching The Backrest. Attach the Backrest Assembly to the Backrest Support using the four socket head screws (Mx0mm) shipped in the Installation Hardware Box. (Fig.-). Attach the backrest cushion to the backrest assembly as follows (Fig.-): -Align key holes on the backside of the backrest cushion with the hooks on the backrest assembly -Press Backrest Cushion against Backrest Assembly, then slide cushion downward to lock in place Note: Make sure that the cushions are hooked at four places and as illustrated below. Backrest Cushion Backrest Assembly Socket Head Screws Hooks Backrest Support Fig. - Fig. - --

Insert Headrest Mechanism bar through cut-out in Headrest Cover, as shown (Fig.-).

. Insert the Headrest Assembly into the slot on top of the Backrest Assembly. (Fig.

11 -. Attaching The Headrest. Attach the Headrest Cushion to the Headrest Mechanism using thee flat head phillips screws (Mx0mm) shipped in the Installation Hardware Box. (Fig.-). Insert Headrest Mechanism bar through cut-out in Headrest Cover, as shown (Fig.-). Slide Headrest Cover over Headrest Mechanism and press firmly together with the Headrest Cushion.. Insert the Headrest Assembly into the slot on top of the Backrest Assembly. (Fig.-9) Headrest Cushion Headrest Mechanism Headrest Assembly Flat Head Phillips Screws Fig. - Headrest Cover Backrest Assembly Fig Attaching the Seat. Slide the Seat Cushion onto the chair as shown, to hook onto to chair frame. (Fig.-0) Seat Cushion. Secure the front end of the Seat Cushion to the chair frame using the two round head phillips screws (Mx0mm) shipped in the Installation Hardware Box. (Fig.-) Seat Cushion Chair Frame Round head Phillips Screws Chair Frame Fig. -0 Fig. - --

After attaching, verify both of the armrests swing outward 0 degrees only. (Fig.-).

slings, slide a sling onto an armrest cushion, then fix an armrest cushion to an

-) The left and right Armrests and cushions are identical and may be installed on

12 -. Attaching The Armrests. Insert the Armrest to the Armrest Bracket and attach it with a pan head screw (Mxmm). After attaching, verify both of the armrests swing outward 0 degrees only. (Fig.-). Assemble the Armrest Cushions to the Armrest using two round head screws (Mx0mm) per Armrest Assembly. (Fig.-) Armrest Armrest Bracket If your Quolis chair has a narrow type backrest with slings, slide a sling onto an armrest cushion, then fix an armrest cushion to an armrest by using two screws. (Fig.-) The left and right Armrests and cushions are identical and may be installed on either side of the chair. Fig. - Pan Head Phillips Screws. Remove a protective plastic film on a touchpad control panel. (Fig.-) Armrest Cushion Sling Armrest Cushion Armrest Armrest Round Head Phillips Screws Round Head Phillips Screws Fig. - Fig. - Fig

. SPEED ADJUSTMENT Seat lowering speed and backrest recline speed can be adjusted with screws on the Solenoid Valve Block.

-) Each solenoid valve corresponds to a specific chair function. (Fig.

Valve Block Fig. - By turning the each speed adjustment screw clockwise, the speed is reduced for the corresponding chair function.

13 . SPEED ADJUSTMENT Seat lowering speed and backrest recline speed can be adjusted with screws on the Solenoid Valve Block. The Solenoid Valve Block is located inside the pump cover, as shown. (Fig.-) Each solenoid valve corresponds to a specific chair function. (Fig.-) SV : Backrest Raising SV : Backrest Reclining SV : Seat Lifting SV : Seat Lowering SV : Swivel Brake Release SV : Seat Shockless SV : Backrest Shockless Solenoid Valve Block Fig. - By turning the each speed adjustment screw clockwise, the speed is reduced for the corresponding chair function. By turning adjustment screws counterclockwise, the corresponding chair function speed is increased. (Fig.-)! CAUTION The chair movement will be locked if the speed is reduced excessively. Oil may leak from the speed control knob if the speed is increased excessively. Backrest Recline Speed Adjustment Screw SV SV Seat Lowering Speed Adjustment Screw SV SV SV SV SV Fig. - Front View (Faces Pump) Fig. - Rear View (Faces Away From Pump) -0-

14 . HYDRAULIC DIAGRAM Solenoid Valve Block Filter SV SV Solenoid Valve Relief Valve Restrictor M SV SV SV Motor Pump SV SV Shockless Solenoid Valve Air-bleeder Oil Reservoir Backrest Cylinder Seat Elevation Cylinder Swivel Lock Cylinder Fig. - Hydraulic Diagram --

15 M. ELECTRICAL DIAGRAM VLP ANFTA0 Trunk Line A for Solenoid Valve Reclining SV CN Up B0P-NV SV CN Down SV -0A (MOLEX) ANFTA0 Trunk LIne for Motor / Capacitor VLP SV Reclining Trunk Line for Capacitor ANFUA0 Solenoid Valve Section (0V) Down Capacitor uf Up / Motor TSM-CBC-LP-M-E Motor Section (V) Rotation Lock ANETA0 Assistant Side VLP SV CN0-0A (MOLEX) Transformer Section(0V) Up/Down Slow Slide ANFTA0 SV Backrest Slow Slide CN BP-VH Touchpad Switch (AGFSA0) SV Up/Down Slow XA0P VLP Backrest Slow ANFTA0 Main Power Switch Section V Lock CN BP-VH Fuse F 0A CN -0A Armrest Membrane SW- L (AGFSA0) Armrest Membrane SW- R (AGFSA0) Up Down Reclining AR P P LP 9 0 Main Switch Trunk Line B for Solenoid Valve 0V 0 9V 9 ANFU0A0 Transformer TK-0V-H Up Down Reclining AR Trunk Line C for Touchpad SW P P LP Lock Cancel Safety V Safety LED. Up Down Reclining AR P P LP Lock Cancel Safety V Safety LED. / Earth CN9-0A (MOLEX) L N ANFTA0 XAP XAP XA9P L N Relay P.C.B. RY-00 CN B0B-XASK-N-A Trunk Line B for Membrane SW ANFTA0 Pink Light / Pink Light / Trunk Line C for Membrane SW ANFTA D Light PCB. CN B0B-XASK-N-A CN B0B-XASK-N-A XAP XAP Power Cable Section CN9 IL-P-SEN ANFT0A0 Distribution P.C.B. (AGFSA0) XAP CN B0P-NV 9 0 (Distribution P.C.B. in the right side armrest) Trunk Line ffor Chair Power Source Motor Up Down Reclining Com Up/Down Slow Slide Lock Cancel Backrest Slow Slide ANFTA0 D Light Communication Line Trunk Line B for Touchpad SW 9 0 Trunk Line A for Membrane SW Pink Light / ANFTA0 ANFTA0 XA9P ANFT0A0 9 NMFP VLP Trunk Line for Dental Light Power Source To Serial Communication Line for Doctor Table ANFTA0 Trunk Line for Relay XAP ANFTB0 Trunk Line A for Touchpad SW Serial Communication Line ANFT9A0 0 ANFTA0 Light Pink Light / DNCSA0 Chair Operation Prohibition CN9 B09B-XASK- CN B0B-XASK- (.) Serial Reception Motor Up Down Reclining (.) Serial Reception Safety Switch for Under Pump Cover Chair Down Prohibition N.O. CN-(-) IL-P-SEN Up/Down Slow Slide Backrest Slow Slide Lock Cancel Up Down Reclining AR P P LP V Lock Cancel Safety Safety LED. Up Down Reclining AR P P LP CN0 IL-0P-SEN (.) Serial Transmission (.) Serial Transmission CN-(-) IL-0P-SEN CN9 B0B-XASK- CN B0B-XASK- CN B0B-XASK- CN-(-) IL-0P-SEN DNCSA0 Chair Operation Prohibition Safety Switch for Under Pump Cover CN-(-) IL-P-SEN N.O. Chair Down Prohibition Base CN IL-P-SEN Limit STORE SW SW Potentiometer for Seat EWS VDA S0 E (Proportional Solenoid Valve) SW MODE SW NOL LIM CN-(-) IL-P-SEN ANDR0A0 Unused CN IL-P-SEN EWS VDA S0 E Potentiometer for Backrest ANDRA0 CN-(-) IL-P-SEN Earth Line CN IL-P-SEN XAP Control P.C.B.(AGFS*0) XX-STD00/00TI Chair upper frame Thermistor Thermistor for Solenoid Valves NTC Thermistor CN IL-P-SEN CN IL-P-SEN CN IL-P-SEN CN IL-P-SEN CN IL-P-SEN CN IL-P-SEN Cap dot indicates male pin side [Remarks] Connector Symbol Plug FLASH --

16 NOTE R BELMONT EQUIPMENT, Division of Takara Belmont USA, Inc. 0 Belmont Drive Somerset, New Jersey 0 U.S.A. TEL.:() / (00) -9 Fax.:()- / (00) 0-0 TAKARA CO, CANADA LTD. 0 S. Sheridan Way, Mississauga, Ont., LJM, Can. TEL.:(90) - Fax.:(90)-0

QUOLIS DENTAL CHAIR. Parts List. Model : Q-5000 (AC-BEL5000) 120V/60Hz. Ver Feb 7, 2012

QUOLIS DENTAL CHAIR. Parts List. Model : Q-5000 (AC-BEL5000) 120V/60Hz. Ver Feb 7, 2012 QUOLIS DENTAL CHAIR Model : Q-000 (AC-BEL000) 0V/0Hz Parts List Ver. 0. Feb, 0 IMPORTANT Not all of the parts indicated in these lists are available by itself. Some of the parts can only be supplied as