Vehicle Level Steering and Suspension Alignment Service and Repair Wheel Alignment. Wheel Alignment
|
|
- John Dwain Ryan
- 6 years ago
- Views:
Transcription
1 Page 1 of Dodge Truck Caravan FWD V6-3.3L VIN R Vehicle Level Steering and Suspension Alignment Service and Repair Wheel Alignment Wheel Alignment PRE-WHEEL ALIGNMENT INSPECTION Before any attempt is made to change or correct the wheel alignment, the following inspection and necessary corrections must be made to ensure proper alignment. 1. Verify that the fuel tank is full of fuel. If the tank is not full, the reduction in weight will affect the curb height of the vehicle and the alignment angles. 2. The passenger and luggage compartments of the vehicle should be free of any load that is not factory equipment. 3. Check the tires on the vehicle. All tires must be the same size and in good condition with approximately the same amount of tread wear. Inflate all the tires to the recommended air pressure. 4. Check the front wheel and tire assemblies for excessive radial runout. 5. Inspect lower ball joints and all steering linkage for looseness, binding, wear or damage. Repair as necessary. 6. Check suspension fasteners for proper torque and retighten as necessary. 7. Inspect all suspension component rubber bushings for signs of wear or deterioration. Replace any faulty bushings or components before aligning the vehicle. 8. Check the vehicle's curb height to verify it is within specifications. Refer to Curb Height Measurement. WHEEL ALIGNMENT SETUP 1. Position the vehicle on an alignment rack. 2. Install all required alignment equipment on the vehicle per the alignment equipment manufacturer's instructions. On this vehicle, a four-wheel alignment is recommended. NOTE: Prior to reading the vehicle's alignment readouts, the front and rear of vehicle should be jounced. Induce jounce (rear first, then front) by grasping the center of the bumper and jouncing each end of vehicle an equal number of times. The bumper should always be released when vehicle is at the bottom of the jounce cycle. 3. Read the vehicle's current front and rear alignment settings. Compare the vehicle's current alignment settings to the vehicle specifications for camber, caster and toe-in. 4. If front camber and caster are not within specifications, proceed to CAMBER AND CASTER. If caster and camber are within specifications, proceed to TOE which can be found following CAMBER AND CASTER. Rear camber, caster and toe are not adjustable. If found not to be within specifications, reinspect for damaged suspension or body components and replace as
2 Page 2 of 7 necessary. CAMBER AND CASTER Camber and caster settings on this vehicle are determined at the time the vehicle is designed, by the location of the vehicle's suspension components. This is referred to as NET BUILD. The result is no required adjustment of camber and caster after the vehicle is built or when servicing the suspension components. Thus, when performing a wheel alignment, caster and camber are not normally considered adjustable angles. Camber and caster should be checked to ensure they meet vehicle specifications. If front camber is found not to meet alignment specifications, it can be adjusted using an available camber adjustment bolt package. Before installing a camber adjustment bolt package on a vehicle found to be outside the specifications, inspect the suspension components for any signs of damage or bending. CAUTION: Do not attempt to adjust the vehicles wheel alignment by heating, bending or by performing any other modification to the vehicle's front suspension components or body. If camber readings are not within specifications, use the following procedure to install the front camber adjustment bolt package and then adjust front camber. CAMBER ADJUSTMENT BOLT PACKAGE INSTALLATION The camber adjustment bolt package contains 2 flange bolts, 2 cam bolts, 2 dog bone washers, and 4 nuts. This package services both sides of the vehicle. Use the package to attach the strut clevis bracket to the steering knuckle after the strut clevis bracket has been modified. To install and adjust the camber adjustment bolt package, follow the procedure below. 1. Raise the vehicle until its tires are not supporting the weight of the vehicle. 2. Remove the front tire and wheel assemblies. CAUTION: When removing the steering knuckle from the strut clevis bracket, do not put a strain on the brake flex hose. Also, do not let the weight of the steering knuckle assembly be supported by the brake flex hose when removed from the strut assembly. If necessary use a wire hanger to support the steering knuckle assembly or if required remove the brake flex hose from the caliper assembly. CAUTION: The knuckle to strut assembly attaching bolt shanks are serrated and must not be turned during removal. Remove the nuts while holding the bolts stationary.
3 Page 3 of 7 3. Remove the top and bottom, strut clevis bracket to steering knuckle attaching boltsand discard. Separate the steering knuckle from the strut clevis bracket and position steering knuckle so it is out of the way of the strut.
4 Page 4 of 7 CAUTION: When slotting the bottom mounting hole on the strut clevis bracket, do not enlarge the hole beyond the indentations on the sides of the strut clevis bracket. 4. Using an appropriate grinder and grinding wheel, slot the bottom hole in both sides of the strut clevis bracket. CAUTION: After slotting the strut clevis bracket hole, do not install the original attaching bolts when assembling the steering knuckle to the strut assembly. Only the flange bolts, cam bolts, and dog bone washers from the service package must be used to attach the steering knuckle to the strut after the mounting hole is slotted. NOTE: The strut clevis-to-knuckle bolts are installed differently on each side of the vehicle. Left-hand side bolts are installed from vehicle rear to front. Right-handside bolts are installed from vehicle front to rear. 5. Position the knuckle back into the strut clevis bracket. Using the direction indicated in the above note, install a flanged bolt from the service package into the upper mounting hole. Using the direction indicated in the above note, install a cam bolt into the bottom mounting hole.
5 Page 5 of 7 6. Install a dog bone washer on the steering knuckle to strut clevis bracket attaching bolts, then install the nuts onto the bolts from the service package. Tighten the bolts just enough to hold the steering knuckle in position when adjusting camber, while still allowing the steering knuckle to move in clevis bracket. 7. Repeat the procedure to the other side strut clevis bracket. 8. Reinstall both front tire and wheel assemblies and tighten to specifications. 9. Lower the vehicle. Jounce the front and rear of vehicle an equal amount of times.
6 Page 6 of Adjust the front camber to the preferred setting by rotating the lower eccentric cam bolt against the cam stop areas on the strut clevis bracket. When camber is set, tighten the upper strut clevis bracket bolt and lower cam bolt. Again jounce front and rear of vehicle an equal amount of times and verify front camber setting. Torque both front strut to steering knuckle attaching bolts to 81 Nm (60 ft. lbs.) plus an additional 1/4 (90 ) turn after the required torque is met. 11. If toe readings obtained are not within the required specification range, adjust toe to meet the preferred specification setting. Toe is adjustable using the following procedure. TOE ADJUSTMENT 1. Center the steering wheel and lock in place using a steering wheel clamp. CAUTION: Do not twist front inner tie rod to steering gear rubber boots during front wheel Toe adjustment.
7 Page 7 of 7 2. Loosen front inner to outer tie rod end jam nuts. Grasp inner tie rods at secretions and rotate inner tie rods of steering gear to set front toe to the preferred toe specification. 3. Tighten tie rod jam nuts to 75 Nm (55 ft. lbs.) torque. 4. Adjust steering gear to tie rod boots at the inner tie rod. 5. Remove steering wheel clamp. 6. Remove the alignment equipment. 7. Road test the vehicle to verify the steering wheel is straight and the vehicle does not wander or pull.
1 of 12 8/25/2017, 4:29 PM
1 of 12 8/25/2017, 4:29 PM STANDARD PROCEDURE - WHEEL ALIGNMENT PRE-WHEEL ALIGNMENT INSPECTION Before any attempt is made to change or correct the wheel alignment, the following inspection and necessary
More informationSUSPENSION 2-1 SUSPENSION CONTENTS
PL SUSPENSION 2-1 SUSPENSION CONTENTS page FRONT SUSPENSION... 10 REAR SUSPENSION... 39 page WHEEL ALIGNMENT... 1 WHEEL ALIGNMENT INDEX page DESCRIPTION AND OPERATION COMPETITION PACKAGE ALIGNMENT... 2
More informationSUSPENSION 2-1 SUSPENSION CONTENTS
ZJ SUSPENSION 2-1 SUSPENSION CONTENTS page ALIGNMENT... 1 FRONT SUSPENSION... 6 page REAR SUSPENSION... 14 ALIGNMENT INDEX page GENERAL INFORMATION WHEEL ALIGNMENT... 1 DIAGNOSIS AND TESTING SUSPENSION
More informationGENERAL INFORMATION. Wheel Alignment Theory & Operation
Fig. 1: Checking Steering Linkage GENERAL INFORMATION Wheel Alignment Theory & Operation ADJUSTMENTS NOTE: This article is intended for general information purposes only. This information may not apply
More informationDIAGNOSIS AND TESTING
DIAGNOSIS AND TESTING SUSPENSION AND STEERING SYSTEM 2007 SUSPENSION Suspension - Nitro CONDITION POSSIBLE CAUSES CORRECTION FRONT END NOISE 1. Loose or worn wheel bearings. 1. Replace wheel bearings.
More informationSUSPENSION 2-1 SUSPENSION CONTENTS
TJ SUSPENSION 2-1 SUSPENSION CONTENTS page ALIGNMENT... 1 FRONT SUSPENSION... 5 page REAR SUSPENSION... 12 ALIGNMENT INDEX page GENERAL INFORMATION WHEEL ALIGNMENT... 1 DIAGNOSIS AND TESTING SUSPENSION
More informationSUSPENSION 2-1 SUSPENSION CONTENTS
TJ SUSPENSION 2-1 SUSPENSION CONTENTS page ALIGNMENT... 1 FRONT SUSPENSION... 6 page REAR SUSPENSION... 13 ALIGNMENT INDEX page DESCRIPTION AND OPERATION WHEEL ALIGNMENT... 1 DIAGNOSIS AND TESTING SUSPENSION
More informationFRONT SUSPENSION GROUP 2 FRONT SUSPENSION 2-1 CONTENTS SPECIFICATIONS VC-1, VC-2, VC-3 VY-1 TOOL LIST. Page
GROUP 2 FRONT SUSPENSION CONTENTS Page Specifications 1 Tool List.... 1 Torque Reference 2 Preparation for Measuring Front End Alignment... 2 Front Suspension Height Adjustment 3 Front Suspension Alignment
More informationSUSPENSION 2-1 SUSPENSION TABLE OF CONTENTS
DN SUSPENSION 2-1 SUSPENSION TABLE OF CONTENTS page ALIGNMENT... 1 FRONT SUSPENSION - 4x2... 6 page FRONT SUSPENSION - 4x4... 14 REAR SUSPENSION... 23 ALIGNMENT TABLE OF CONTENTS page AND OPERATION WHEEL
More informationSUSPENSION 2-1 SUSPENSION TABLE OF CONTENTS
XJ SUSPENSION 2-1 SUSPENSION TABLE OF CONTENTS page ALIGNMENT... 1 FRONT SUSPENSION... 7 page REAR SUSPENSION... 16 ALIGNMENT TABLE OF CONTENTS page AND WHEEL ALIGNMENT...1 DIAGNOSIS AND TESTING SUSPENSION
More informationSECTION 16 STEERING SYSTEM CONTENTS GENERAL DESCRIPTION REMOVAL (Steering Wheel, and Steering Gear Case)
SECTION 16 STEERING SYSTEM CONTENTS 16-1. GENERAL DESCRIPTION......... 16-2 16-2. REMOVAL... 16-3 (Steering Wheel, and Steering Gear Case) 16 3. DISASSEMBLY (Steering Gear Case)... 16-4 16 4. ASSEMBLY
More informationSUSPENSION 2-1 SUSPENSION CONTENTS
WJ SUSPENSION 2-1 SUSPENSION CONTENTS page ALIGNMENT... 1 FRONT SUSPENSION... 4 page REAR SUSPENSION... 15 ALIGNMENT INDEX page AND WHEEL ALIGNMENT... 1 SERVICE PROCEDURES PRE-ALIGNMENT... 2 AND WHEEL
More informationThis file is available for free download at
This file is available for free download at http://www.iluvmyrx7.com This file is fully text-searchable select Edit and Find and type in what you re looking for. This file is intended more for online viewing
More information2004 SUSPENSION. Wheel Alignment - Corvette. Caster Cross +/ / Fastener Tightening Specifications Specification Application
2004 SUSPENSION Wheel Alignment - Corvette SPECIFICATIONS WHEEL ALIGNMENT SPECIFICATIONS Wheel Alignment Specifications Camber Cross Caster Cross Suspension Camber Tolerance Caster Tolerance FE1 & FE3
More informationSUSPENSION 2-1 SUSPENSION CONTENTS
DN SUSPENSION 2-1 SUSPENSION CONTENTS page ALIGNMENT... 1 FRONT SUSPENSION... 5 page REAR SUSPENSION... 13 ALIGNMENT INDEX page GENERAL INFORMATION WHEEL ALIGNMENT... 1 DIAGNOSIS AND TESTING PRE-ALIGNMENT
More informationSECTION 3A WHEEL ALIGNMENT
SECTION 3A WHEEL ALIGNMENT NOTICE: All wheel alignment fasteners are important attaching parts in that they could affect the performance of vital components and systems, and/or could result in major repair
More informationWHEEL ALIGNMENT SPECIFICATIONS & PROCEDURES
WHEEL ALIGNMENT SPECIFICATIONS & PROCEDURES 1988 Jeep Cherokee 1988 Wheel Alignment INTRODUCTION PRE-ALIGNMENT VEHICLE CHECKS Prior to making wheel alignment adjustments, check and adjust the following
More informationSUSPENSION - FRONT Toyota Celica DESCRIPTION ADJUSTMENTS & INSPECTION WHEEL ALIGNMENT SPECIFICATIONS & PROCEDURES WHEEL BEARING
SUSPENSION - FRONT 1988 Toyota Celica FRONT SUSPENSION Toyota DESCRIPTION Vehicles are equipped with front wheel drive and independent MacPherson strut front suspension. Suspension consists of vertically
More informationChrysler A-Body Tubular A-Arms Installation Instructions A-ARM INSTALLATION
1967-1976 Dodge Demon 1112 67-72 Chrysler A-Body Tubular A-Arms Installation Instructions Thank you for your purchase of this Hotchkis Performance product. Your A-Arm set was designed with the performance
More informationWhy do cars need Alignment
Why do cars need Alignment The main purpose of wheel alignment is to make the tires roll without Scuffing, slipping, or dragging under all operating conditions. Caster Camber Toe Steering axis inclination
More informationWheel Bearing and Wheel Hub All-Wheel Drive (AWD) Vehicles
Rear Suspension Wheel Bearing and Wheel Hub All-Wheel Drive (AWD) Vehicles All-Wheel Drive (AWD) Vehicles Front Wheel Drive (FWD) Vehicles Removal All vehicles NOTICE: Suspension fasteners are critical
More informationReturn To Main Table of Contents GENERAL... 2 STRUT ASSEMBLY LOWER ARM STABILIZER BAR CENTER MEMBER WHEEL AND TIRE...
FRONT SUSPENSION Return To Main Table of Contents GENERAL... 2 STRUT ASSEMBLY... 11 LOWER ARM... 13 STABILIZER BAR... 17 CENTER MEMBER... 19 WHEEL AND TIRE... 21 GENERAL GENERAL SPECIFICATIONS Suspension
More informationGroup 2 FRONT SUSPENSION CONTENTS
FRONT SUSPENSION 1 Group 2 FRONT SUSPENSION CONTENTS Paragraph Page Front Wheel Bearing Adjustment 8 5 Front Suspension Height Adjustment 9 5 Using Tool C-3608 Without Using Tool C-3608 Front Wheel Alignment
More information1. General Description
General Description 1. General Description A: SPECIFICATION Front Rear Model Wheel arch height (Tolerance: +12 mm 24 mm ( +0.47 in 0.94 in)) mm (in) 376 (14.8) Camber (Tolerance: 0 45 Differences between
More information2. MEASURE VEHICLE HEIGHT. (b) Measure the vehicle height. Measurement points: C: Ground clearance of front wheel center
ADJUSTMENT If the wheel alignment has been adjusted, and if suspension or underbody components have been removed/installed or replaced, be sure to perform the following initialization procedure in order
More informationSECTION 2C FRONT SUSPENSION TABLE OF CONTENTS
SECTION 2C FRONT SUSPENSION TABLE OF CONTENTS Description and Operation... 2C-2 Front Suspension... 2C-2 Specifications... 2C-4 Component Locator... 2C-5 Front Suspension Assembly... 2C-5 Cross-Sectional
More informationAER Automotive Steering and Suspension
2013 NATEF JOB TASKS COMPLETION REQUIREMENT: P1-95% P2-80% P3-50% Student Name: DETAILED COURSE CONTENT AUTOMOTIVE SUSPENSION AND STEERING TECHNICIAN DEMONSTRATE PROFICIENCY IN SUSPENSION AND STEERING
More informationFRONT WHEEL ALIGNMENT
2 Front: B A A Rear: C D Front SUENSION FRONT WHEEL ALIGNMENT D F046082E03 B FRONT WHEEL ALIGNMENT ADJUSTMENT 1. INECT TIRE (a) Inspect the tires (see page TW-3). 2. MEASURE VEHICLE HEIGHT Standard vehicle
More informationWheel Alignment. Wheel arch height (front and rear wheels) <Ref. to FS-8, WHEEL ARCH HEIGHT, INSPECTION, Wheel Alignment.>
2. Wheel lignment : INSPECTION Check the following items before taking wheel alignment measurement. Check items before taking wheel alignment measurement: Tire inflation pressure Unbalanced right and left
More informationINSTALLATION INSTRUCTION Rev A
INSTALLATION INSTRUCTION 88587 Rev A FOR RANCHO SUSPENSION SYSTEM RS6587B: 2009 DODGE RAM 1500 READ ALL INSTRUCTIONS THOROUGHLY FROM START TO FINISH BEFORE BEGINNING INSTALLATION IMPORTANT NOTES! WARNING:
More informationWHEEL ALIGNMENT PROCEDURES
WHEEL ALIGNMENT PROCEDURES PRE-ALIGNMENT CHECKS Ensure steering wheel is centered and front wheels are in straight-ahead position (to correct, shorten one tie rod adjusting sleeve and lengthen the opposite
More informationWHEEL ALIGNMENT. Wheel arch height (Front and rear) <Ref. to FS-7, WHEEL ARCH HEIGHT, INSPECTION, Wheel Alignment.>
2. Wheel Alignment A: INSPECTION Check the following items before taking wheel alignment measurement. Check items before taking wheel alignment measurement: tire air pressure unbalanced right and left
More informationCamber Angle. Wheel Alignment. Camber Split. Caster Angle. Caster and Ride Height. Toe Angle. AUMT Wheel Alignment
AUMT 1316 - Wheel Alignment 11/15/11 Camber Angle Wheel Alignment Donald Jones Brookhaven College Camber Split Camber is the amount that the centerline of the wheel tilts away from true vertical when viewed
More informationEibach Pro-Damper Shocks & Struts (05-09 All):
Eibach Pro-Damper Shocks & Struts (05-09 All): Required tools: 3/8 and 1/2 drive ratchets 7, 8, 10, 15, 16, 17, 18, 21 & 22 mm open ended wrenches 8 & 10 mm box end wrenches 10mm socket 13, 15 & 18 mm
More informationINDEX GENERAL. Page Connecting Rod 2M-3 Front Wheel Alignment 2M-4 Front Wheel Shimmy 2M-5 General 2M-1
INDEX Page Connecting Rod 2M-3 Front Wheel Alignment 2M-4 Front Wheel Shimmy 2M-5 General 2M-1 Pago Specifications 21-8 Steering Damper 2M-3 Steering Wheel Spoke Alignment 2M-5 Tie Rod 2M-3 GENERAL The
More information2012 Taurus Workshop Manual. DISASSEMBLY AND ASSEMBLY Procedure revision date: 07/14/2011
SECTION 204-01: Front Suspension DISASSEMBLY AND ASSEMBLY Procedure revision date: 07/14/2011 Strut and Spring Assembly Material Item Silicone Brake Caliper Grease and Dielectric Compound XG-3-A Specification
More informationColorado/ Canyon 4, 5, and 6 Lift Kit
*1221BAG3* 1221BAG3 921221200B 2015-16 Colorado/ Canyon 4, 5, and 6 Lift Kit Thank you for choosing Rough Country for all of your suspension needs. Rough Country recommends a certified technician installs
More information2003 Dodge Pickup R DRIVE AXLES' 'Axle Shafts - Front - Ram Pickup WD DRIVE AXLES
2002-04 DRIVE AXLES Axle Shafts - Front - Ram Pickup 1500 4WD DESCRIPTION Vehicles equipped with 4WD and C205F front axle assembly use equal length axle shaft system to deliver power from front differential
More information2013 NATEF Task Area A-4 Suspension, Steering, Alignment7-2013
2013 NATEF Task Area A-4 Suspension, Steering, Alignment7-2013 A. Steering System Diagnosis & Repair B. Suspension System Diagnosis & Repair C. Wheel Alignment Diagnosis & Adjustment D. Wheel & Tire Diagnosis
More informationFRONT SUSPENSION AND STEERING LINKAGE
A FRONT SUSPENSION AND STEERING LINKAGE CONTENTS GROUP 2 Page LOWER BALL JOINTS 12 LOWER CONTROL ARM AND SHAFT... 9 LOWER CONTROL ARM STRUT 12 PRE-ALIGNMENT INSPECTION Height Adjustment., 4 RUBBER ISOLATED
More information1990 SUSPENSION Front ES250, LS400
SUSPENSION - FRONT Article Text 1990 Lexus LS 400 For Lextreme Copyright 1998 Mitchell Repair Information Company, LLC Thursday, January 29, 2004 04:56PM ARTICLE BEGINNING 1990 SUSPENSION Front ES250,
More informationSection I TORSION-AIRE FRONT WHEEL SUSPENSION CONTENTS DATA AND SPECIFICATIONS MANUAL STEERING WITH POWER STEERING SPECIAL TOOLS
CHRYSLER SERVICE MANUAL FRONT WHEEL SUSPENSION 7 Section I TORSION-AIRE FRONT WHEEL SUSPENSION CONTENTS Page Servicing the Front Wheel Suspension 10 Checking Front Suspension Height.. 12 Front Wheel Alignment
More informationINSTALLATION INSTRUCTION 89400
INSTALLATION INSTRUCTION 89400 FOR RANCHO SUSPENSION SYSTEM RS66400B: 2012 RAM 1500 4WD. READ ALL INSTRUCTIONS THOROUGHLY FROM START TO FINISH BEFORE BEGINNING INSTALLATION Rev B IMPORTANT NOTES! WARNING:
More informationPage 1 of 8 SECTION 204-00: Suspension System - General Information 1998 Contour/Mystique Workshop Manual DIAGNOSIS AND TESTING Procedure revision date: 09/14/2001 Suspension System Special Tool(s) Dial
More informationFRONT AXLE AND SUSPENSION FA 1
FRONT AXLE AND SUSPENSION FA1 FRONT AXLE AND SUSPENSION FA2 FRONT AXLE AND SUSPENSION Troubleshooting TROUBLESHOOTING Problem Possible cause Remedy Page Wanders/pulls Tires worn or improperly inflated
More informationSUSPENSION. Front - Corvette
1998-99 SUSPENSION Front - Corvette DESCRIPTION The major suspension components are made of high-strength, lightweight, forged aluminum alloy. A fiberglass single-leaf spring is mounted transversely below
More informationPRE-INSTALLATION. INSTALLATION INSTRUCTIONS STEP 1: Park vehicle on level surface and chock rear wheels.
2007-2013 7.5" GMC/Chevrolet 1500 4WD Suspension Lift kit PRE-INSTALLATION 15004 2 - Cross-member (Fr/Rr) 2 - Sway Bar Drop Bracket 2 - Knuckle (Dr/Pass) 1 - Driver Diff. Bracket 1 - Passenger Diff. Bracket
More informationM-FR3-FA Fiesta Handling Pack INSTALLATION INSTRUCTIONS
Please visit www.fordracingparts.com for the most current instruction information!!! PLEASE READ ALL OF THE FOLLOWING INSTRUCTIONS CAREFULLY PRIOR TO INSTALLATION. AT ANY TIME YOU DO NOT UNDERSTAND THE
More informationFor the 4 lift application we recommend an 18 wheel not to exceed 9 in width with 5 of backspacing/ 0 offset and a 275/65-18 tire.
921221200F *1221BAG16* 1221BAG16 2015-18 Colorado/ Canyon 4 and 6 Lift Kit Thank you for choosing Rough Country for all of your suspension needs. Rough Country recommends a certified technician installs
More informationREAR SUSPENSION GROUP CONTENTS GENERAL DESCRIPTION REAR SUSPENSION DIAGNOSIS LOWER ARM AND TOE CONTROL ARM ASSEMBLY...
34-1 GROUP 34 CONTENTS GENERAL DESCRIPTION........... 34-2 DIAGNOSIS.... 34-2 INTRODUCTION....................... 34-2 TROUBLESHOOTING STRATEGY........ 34-2 SYMPTOM CHART..................... 34-3 SYMPTOM
More informationThis file is available for free download at
This file is available for free download at http://www.iluvmyrx7.com This file is fully text-searchable select Edit and Find and type in what you re looking for. This file is intended more for online viewing
More informationPage 1 of 11 1Search FRAME CROSS BAR 2001 Chrysler PT Cruiser 2.4L Eng Base CAUTION: DO NOT attempt to modify any suspension or steering components by heating or bending. Removal [ STABILIZER BAR ] 1.
More informationREAR SUSPENSION GROUP CONTENTS GENERAL DESCRIPTION TRAILING ARM ASSEMBLY REAR SUSPENSION DIAGNOSIS
34-1 GROUP 34 CONTENTS GENERAL DESCRIPTION......... 34-2 DIAGNOSIS.. 34-3 INTRODUCTION TO DIAGNOSIS........................ 34-3 DIAGNOSIS TROUBLESHOOTING STRATEGY...... 34-3 SYMPTOM CHART...................
More informationTOYOTA COROLLA LOWERING SPRINGS Preparation
Preparation Part Number: PTR07-02140 Kit Contents Item # Quantity Reqd. Description 1 2 Front Spring 2 2 Rear Spring 3 1 Hardware 4 1 Instruction Form Hardware Bag Contents Item # Quantity Reqd. Description
More information2002 Chrysler PT Cruiser
1. Raise the vehicle. 2. Remove tire and wheel assembly. 3. If both strut assemblies are to be removed, mark the strut assemblies right or left according to which side of the vehicle they were removed
More information07-UP AVALANCHE 7.5 KIT
92120900R1 07-UP AVALANCHE 7.5 KIT Thank you for choosing Rough Country for your suspension needs. We appreciate your business!! This kit will not fit vehicles equipped with electric steering or trucks
More informationREAR SUSPENSION GROUP CONTENTS GENERAL DESCRIPTION TRAILING ARM REAR SUSPENSION DIAGNOSIS TOE CONTROL ARM...
34-1 GROUP 34 CONTENTS GENERAL DESCRIPTION 34-2 DIAGNOSIS 34-3 INTRODUCTION TO DIAGNOSIS 34-3 DIAGNOSTIC TROUBLESHOOTING STRATEGY 34-3 SYMPTOM CHART 34-3 SYMPTOM PROCEDURES 34-3 SPECIAL TOOLS 34-5 ON-VEHICLE
More information97-06 JEEP TJ/LJ LONG ARM UPGRADE KIT
921663U00 97-06 JEEP TJ/LJ LONG ARM UPGRADE KIT Thank you for choosing Rough Country for your suspension needs. This kit is an upgrade kit only. This kit includes frame mounting points and adjustable long
More information1970 Trans-Am Mustang Front Suspension Instructions. Manual, Volume One, Chassis. Special instructions and precautions will be given
1970 Trans-Am Mustang Front Suspension Instructions 1. This kit was designed to be used in conjunction with the Rear Suspension kit. 2. This conversion follows standard procedures as described in the 1970
More informationDetroit Speed, Inc. Detroit Speed Control Arm and Spindle Kit A-Body P/N: &
Detroit Speed, Inc. Detroit Speed Control Arm and Spindle Kit 1964-72 A-Body P/N: 030104 & 030105 The Detroit Speed A-Body front suspension kit is a bolt-on package that addresses the shortcomings of the
More informationGROUP 33A 33A-1 CONTENTS GENERAL DESCRIPTION... 33A-2 FRONT SUSPENSION DIAGNOSIS. 33A-3 LOWER ARM... 33A-13 SPECIAL TOOLS... 33A-5
33A-1 GROUP 33A CONTENTS GENERAL DESCRIPTION 33A-2 DIAGNOSIS 33A-3 INTRODUCTION TO FRONT SUSPENSION DIAGNOSIS 33A-3 DIAGNOSIS TROUBLESHOOTING STRATEGY 33A-3 SYMPTOM CHART 33A-3 SYMPTOM PROCEDURES 33A-3
More informationOVERVIEW: This bulletin involves **installing a rubber gasket** to the face of the half shaft that mounts to the hub bearing.
NUMBER: GROUP: 03-001-03 REV. A Axle and Propshaft DATE: Sept. 19, 2003 This bulletin is supplied as technical information only and is not an authorization for repair. No part of this publication may be
More informationFRONT SUSPENSION GROUP 33A 33A-1 CONTENTS GENERAL DESCRIPTION... 33A-2 FRONT SUSPENSION DIAGNOSIS. 33A-3 LOWER ARM... 33A-13 SPECIAL TOOLS...
33A-1 GROUP 33A FRONT SUSPENSION CONTENTS GENERAL DESCRIPTION......... 33A-2 DIAGNOSIS. 33A-3 INTRODUCTION TO DIAGNOSIS........................ 33A-3 DIAGNOSIS TROUBLESHOOTING STRATEGY...... 33A-3 SYMPTOM
More information1 Part Number: M-2300-Y Part Description: S550 Mustang-Shelby Brake Upgrade Kit Installation Instructions
Please visit www.performanceparts.ford.com for the most current instruction and warranty information. PLEASE READ ALL OF THE FOLLOWING INSTRUCTIONS CAREFULLY PRIOR TO INSTALLATION. AT ANY TIME YOU DO NOT
More informationThis file is available for free download at
This file is available for free download at http://www.iluvmyrx7.com This file is fully text-searchable select Edit and Find and type in what you re looking for. This file is intended more for online viewing
More informationSuspension System RS6582B
Suspension System RS6582B Tahoe/Yukon READ ALL INSTRUCTIONS THOROUGHLY FROM START TO FINISH BEFORE BEGINNING INSTALLATION IMPORTANT NOTES! WARNING: This suspension system will enhance the off-road performance
More information#~ nt cond1t1on: Full tank of fu 1 ns
tjfl cifications,pe,. eel Aligment Specificati # nt cond1t1on: Full tank of fu 1 ns igrirried on flat level surface e ' no Passen d pla Qers 9 VVh I rn ents.. Wheel Alignment 16129 :: eel A 1gnment Cr
More information1988 Chevrolet Pickup V SUSPENSION - FRONT (4WD)' 'Front Suspension - "V" Series 1988 SUSPENSION - FRONT (4WD) Front Suspension - "V" Series
1988 SUSPENSION - FRONT (4WD) Front Suspension - "V" Series DESCRIPTION NOTE: Vehicle serial numbers used in this article has been abbreviated for common reference to Chevrolet and GMC models. Chevrolet
More informationFour-Wheel Alignment ( )
Published: Mar 7, 2005 Four-Wheel Alignment (57.65.04) CAUTION: Make sure the vehicle is on a flat level surface. CAUTION: Make sure the tire pressures are within specification. CAUTION: Make sure that
More information1. SPECIFICATIONS 2. WHEEL ALIGNMENT
441101 083 1. SPECIFICATIONS Front Suspension Rear Suspension Description Suspension type Spring type Shock absorber type Stabilizer bar type Suspension type Spring type Shock absorber type Stabilizer
More informationHemet High School NATEF SUSPENSION AND STEERING CHECKLIST. Name Date Period
Hemet High School NATEF SUSPENSION AND STEERING CHECKLIST Name Period For every task in Suspension and Steering, the following safety requirement must be strictly enforced: Comply with personal and environmental
More information1. SPECIFICATIONS 2. WHEEL ALIGNMENT Front Suspension. (gas type) Rear Suspension. (gas type)
441101 053 1. SPECIFICATIONS Front Suspension Rear Suspension Description Suspension type Spring type Shock absorber type Stabilizer bar type Suspension type Spring type Shock absorber type Stabilizer
More informationFRONT & REAR SUSPENSION SECTIONSU CONTENTS IDX. FRONT SUSPENSION...2 Precautions...2
FRONT & REAR SUSPENSION SECTIONSU GI MA EM LC CONTENTS EC FE FRONT SUSPENSION...2 Precautions...2 PRECAUTIONS...2 Preparation...2 SPECIAL SERVICE TOOLS...2 COMMERCIAL SERVICE TOOLS...2 Noise, Vibration
More informationFRONT & REAR SUSPENSION SECTIONSU CONTENTS IDX. FRONT SUSPENSION...2 Precautions...2. REAR SUSPENSION...14 Precautions...14
FRONT & REAR SUSPENSION SECTIONSU GI MA EM LC EC CONTENTS FE FRONT SUSPENSION...2 Precautions...2 PRECAUTIONS...2 Preparation...2 SPECIAL SERVICE TOOLS...2 COMMERCIAL SERVICE TOOLS...2 Noise, Vibration
More informationcfr angle kit INSTALLATION INSTRUCTIONS: 2009-present nissan 370z z infiniti g37 v36 Part Numbers: VOO-akns-0400
cfr angle kit INSTALLATION INSTRUCTIONS: 2009-present nissan 370z z34 2008-2013 infiniti g37 v36 Part Numbers: VOO-akns-0400 We recommend that installation of all Voodoo13 parts be completed by a professional
More information1 of 9 7/24/2014 9:02 PM
1 of 9 7/24/2014 9:02 PM Four-Wheel Alignment Special Service Tools 204-805 CAUTION: Make sure the vehicle is on a flat level surface. CAUTION: Make sure the tire pressures are within specification. CAUTION:
More informationOVERVIEW: KIT INCLUDES:
Please visit www.fordracingparts.com for the most current instruction information!!! PLEASE READ ALL OF THE FOLLOWING INSTRUCTIONS CAREFULLY PRIOR TO INSTALLATION. AT ANY TIME YOU DO NOT UNDERSTAND THE
More informationINSTALLATION INSTRUCTION 88581
INSTALLATION INSTRUCTION 88581 FOR RANCHO SUSPENSION SYSTEM RS6581B: DODGE RAM READ ALL INSTRUCTIONS THOROUGHLY FROM START TO FINISH BEFORE BEGINNING INSTALLATION Rev C IMPORTANT NOTES! WARNING: This suspension
More informationAEV30308AA Last Updated: 05/31/18. 4 DUALSPORT sc SUSPENSION system for RAM 1500 air ride standard and rebel INSTALLATION GUIDE
AEV30308AA Last Updated: 05/31/18 4 DUALSPORT sc SUSPENSION system for RAM 1500 air ride standard and rebel INSTALLATION GUIDE PLEASE READ BEFORE YOU START TO GUARANTEE A QUALITY INSTALLATION, WE RECOMMEND
More informationNext, chase the threads in the lower A-arm mounts with the 5/8-18 tap and blowout any remaining particles.
Next, chase the threads in the lower A-arm mounts with the 5/8-18 tap and blowout any remaining particles. Now, apply some anti-seize to the threads of the pivot stud. Also put anti-seize inside the bore
More information1940 Hudson SERVICING THE FRONT SUSPENSION SYSTEM
1940 Hudson SERVICING THE FRONT SUSPENSION SYSTEM Source of this material is from 1940 Series, Issue 3, November-December Hudson Service Magazine SERVICING THE FRONT SUSPENSION SYSTEM No set rule can be
More informationSCION tc LOWERING SPRINGS Preparation
Preparation Part Number: PTR11-21100 PTR11-21100-50 Kit Contents Item # Quantity Reqd. Description 1 2 Front Spring 2 2 Rear Spring 3 2 Locking Nut 4 2 Spring Bumper, Front 5 1 Instruction Form Hardware
More informationINSTALLATION INSTRUCTION 88146
INSTALLATION INSTRUCTION 88146 Rev H FOR RANCHO SUSPENSION SYSTEM RS6547: 4WD SUBURBAN/YUKON XL, 4WD TAHOE/YUKON, & 4WD AVALANCHE READ ALL INSTRUCTIONS THOROUGHLY FROM START TO FINISH BEFORE BEGINNING
More informationINSTALLATION INSTRUCTION 88148
INSTALLATION INSTRUCTION 88148 Rev C For Rancho Suspension Systems RS6548, RS6549 & RS6550: GM 2500HD, 2500, and 1500HD Trucks READ ALL INSTRUCTIONS THOROUGHLY FROM START TO FINISH BEFORE BEGINNING INSTALLATION
More information02-10 GM 2500HD / HD & HD CLASSIC 6 2WD SUSPENSION KIT
92122000 92127400 02-10 GM 2500HD / 01-06 1500HD & 07 1500HD CLASSIC 6 2WD SUSPENSION KIT Thank you for choosing Rough Country for your suspension needs. Rough Country recommends a certified technician
More informationSR11 Steering, Rack-And-Pinion
Uniform Procedures For Collision Repair SR11 Steering, Rack-And-Pinion SR Menu Procedure Menu 1. Description This procedure describes diagnosis, replacement, and inspection of a rack-and-pinion steering
More information2004 Dodge Stratus ES. Access for the nuts attaching the rear shock assembly upper mount to the vehicle is through the inside of the trunk.
REMOVAL - SHOCK ASSEMBLY NOTE: Access for the nuts attaching the rear shock assembly upper mount to the vehicle is through the inside of the trunk. 1. Roll back carpeting on top of the rear shock tower
More information04-08 FORD F150 4 KIT
9257700 04-08 FORD F50 4 KIT THANK YOU FOR CHOOSING ROUGH COUNTRY FOR YOUR SUSPENSION NEEDS. Rough Country recommends a certified technician install this system. In addition to these instructions, professional
More informationREMOVAL AND INSTALLATION
204-00-1 Suspension System 204-00-1 REMOVAL AND INSTALLATION Wheel Bearing, Hub, Knuckle, Upper Arm and Lower Arm Rear Special Tool(s) 3. Remove the parts in the order indicated in the following illustrations
More information99-04 GT. Hellion Power Systems Mustang GT Kit Instructions
Hellion Power Systems 99-04 Mustang GT Kit Instructions Part 1 Hellion recommends that the front suspension system be installed either by trained professionals or by 5.Remove rack bolts K-Member Installation
More information»Product» Safety Warning
#F2622 Installation Instructions 1997-2003 Ford F-150 4WD 6" Suspension System Read and understand all instructions and warnings prior to installation of product and operation of vehicle. Zone Offroad
More informationSUBJECT: NO: Honk Or Squeal Noise During Parking Lot Maneuvers GROUP: Steering. DATE: Aug. 28, 1998
SUBJECT: NO: 19-05-98 Honk Or Squeal Noise During Parking Lot Maneuvers GROUP: Steering DATE: Aug. 28, 1998 THIS BULLETIN SUPERSEDES TECHNICAL SERVICE BULLETINS 19-07-97, DATED MAY 9, 1997 AND 19-11-97,
More informationSPRINGS AND SHOCK ABSORBERS
GROUP 17 SPRINGS AND SHOCK ABSORBERS CONIINTS Page DESCRIPTION... 1 SERVICE DIAGNOSIS 1 REAR SPRINGS 3 Page SHOCK ABSORBERS...... 2 SPECIFICATIONS (At Rear of Manual) TIGHTENING REFERENCE... (At Rear of
More informationSUSPENSION SYSTEM PROBLEM SYMPTOMS TABLE SP 1
SUENSION SUENSION SYSTEM 1 Vehicle/pulls Bottoming Sway/pitches Wheel shimmy Abnormal tire wear SUENSION SYSTEM PROBLEM SYMPTOMS TABLE Use the table below to help determine the cause of the problem. The
More informationINSTALLATION INSTRUCTION 88088
INSTALLATION INSTRUCTION 88088 For Rancho Suspension Systems RS6588 & RS6589: FORD F-150 READ ALL INSTRUCTIONS THOROUGHLY FROM START TO FINISH BEFORE BEGINNING INSTALLATION Rev B IMPORTANT NOTES! WARNING:
More information07-13 TOYOTA TUNDRA 2WD 6" LIFT SPINDLES
MAXTRAC SUSPENSION 4030 E LEAVERTON CT ANAHEIM, CA 92807 714-630-0363 WWW.MAXTRACSUSPENSION.COM SALES@MAXTRACSUSPENSION.COM PRODUCT: K886764 07-13 TOYOTA TUNDRA 2WD 6" LIFT SPINDLES PARTS LIST QTY LIFT
More informationSUSPENSION AND AXLE SA 1 SUSPENSION AND AXLE
SA1 SA2 Troubleshooting TROUBLESHOOTING Problem Possible cause Remedy Front Page Rear Wanders/pulls Tires worn or improperly inflated Wheel alignment incorrect Hub bearing worn Front or rear suspension
More informationPart # Mustang Tru-Turn Suspension Package
350 S. St. Charles St. Jasper, In. 47546 Ph. 812.482.2932 Fax 812.634.6632 www.ridetech.com Part # 12099599 64-66 Mustang Tru-Turn Suspension Package Front Components: 1 12093699 Upper Strong Arms 1 12092899
More informationFRONT & REAR SUSPENSION SECTIONSU CONTENTS IDX. FRONT SUSPENSION...2 Precautions...2. Service Data and Specifications (SDS)...21
FRONT & REAR SUSPENSION SECTIONSU GI MA EM LC EC CONTENTS FE...2 Precautions...2 PRECAUTIONS...2 Preparation...2 SPECIAL SERVICE TOOLS...2 COMMERCIAL SERVICE TOOLS...2 Noise, Vibration and Harshness (NVH)
More informationATASA 5 th. Wheel Alignment. Please Read The Summary. ATASA 5 TH Study Guide Chapter 47 Pages: Wheel Alignment 64 Points
ATASA 5 TH Study Guide Chapter 47 Pages: 1403 1423 64 Points Please Read The Summary Before We Begin Keeping in mind the Career Cluster of Transportation, Distribution & Logistics Ask yourself: What careers
More information