C5 II - B2CG51P0 - Remove - refit : Hydraulic valve block and electrovalves REMOVE - REFIT : HYDRAULIC VALVE BLOCK AND ELECTROVALVES AUTO GEARBOX AL4
|
|
- Ursula Randall
- 6 years ago
- Views:
Transcription
1 Page 1 of 8 REMOVE - REFIT : HYDRAULIC VALVE BLOCK AND ELECTROVALVES AUTO GEARBOX AL4 URGENT : Ensure that the precautions relating to safety and cleanliness are adhered to (refer to the brochure: "RECOMMENDATIONS - PRECAUTIONS"). 1. Recommended tools Figure : E5AP12ZC [ 1] Adjusting screw for the internal selection control (-).0338 M1.
2 Page 2 of 8 Figure : E5AP130C [2] Adjusting shim for the internal selection control (-).0338 M2. 2. Removing 2.1. Hydraulic valve block Place the vehicle on a lift. Disconnect the positive and negative battery terminals. Remove the air cleaner. Place a tray to retrieve the oil from the hydraulic valve block housing (approximately 0,5 litres). Figure : B2CP3EQC Remove : The fixing screws for the cover (1) The cover (1)
3 Page 3 of 8 Figure : B2CP2ERD A : EW engine. B : DW engine. Unclip the connectors from the sequence electrovalves, by carefully using a screwdriver as a lever. Disconnect the 6 sequence electrovalves. Remove the 7 screws (2) (engine EW). Remove the 9 screws (2) (engine DW). Figure : B2CP2ESC Release the hydraulic valve block (3). Disconnect electrovalves (5) and (6).
4 Page 4 of 8 Remove the hydraulic valve block (3). URGENT : Do not drop the manual valve (4) Electrovalves of the hydraulic valve block Figure : B2CP3ETD (7) Sequence electrovalve EVS1. (8) Sequence electrovalve EVS2. (9) Sequence electrovalve EVS3. (10) Sequence electrovalve EVS4. (11) Sequence electrovalve EVS5. (12) Sequence electrovalve EVS6. (5) Main pressure modulation electrovalve (pressure EVM). (6) Converter pressure modulation electrovalve (lock-up EVM). (4) Manual valve. N.B. : The hydraulic block does not have to be removed to remove the sequence electrovalves. URGENT : When the electrovalve (11) has been removed, hold the hydraulic slide valve controlled by the electrovalve so that it does not drop. URGENT : Replace the electrovalve seals every time they are reassembled. N.B. : The electrovalve mounting screws should be tightened to 1 ± 0,1 m.dan. 3. Refitting
5 Page 5 of 8 Figure : B2CP321C URGENT : Check that the seals ( 13) (new seals). Position the hydraulic valve block (3). Reconnect electrovalves (5) and (6). Figure : B2CP3EUC CAUTION : Ensure that the manual valve (4) engages on the lug (a) of the toothed quadrant (14).
6 Page 6 of 8 Figure : B2CP3EVD A : EW engine. B : DW engine. Refit the hydraulic valve block mounting screws : Pre-tighten the screws to 0,9 ± 0,09 m.dan (in any order) Slacken the bolts Tighten finally to 0,75 ± 0,07 danm (in the order shown) EW engine = (in order 1 to 7). DW engine = (in order 1 to 9). Reconnect the 6 sequence electrovalves. URGENT : Adjust the internal control, the arm (15) and the toothed quadrant (14) (see the relevant operation). Ensure that the gear selection control works properly in all the positions. Fit : The cover (1) (equipped with a new seal) The fixing screws for the cover (1) Tighten to 1 danm The air cleaner Reconnect the battery positive and negative terminals. Carry out : Fill and top up the automatic gearbox oil (see the relevant operation) An update of the value of the used oil counter (see the relevant operation) 4. Adjusting the internal selection control URGENT : This adjustment must be made whenever repairs involving the hydraulic valve block or internal selection control are carried out.
7 Page 7 of 8 Figure : B2CP3EWD The adjustment takes place with the hydraulic valve block cover ( 1) removed. URGENT : Put the lever (2) in position 16 and hold it against its mechanical stop during the procedure. N.B. : To put the lever (2) in position 16, push it fully forward against its stop. Loosen the shouldered screw (17). Fit the roller "b" of the plate (15) into the position 2 notch of the notched sector (14). Remove the bolt (18).
8 Page 8 of 8 Figure : B2CP3B5C Bring the tool [2] into contact with the width of the arm (15) in line with the screw (18). Lock the assembly using the knurled adjusting screw [1]. Tighten the screw (17) to 0,9 ± 0,09 m.dan. Remove tools [1] and [2]. Refit and tighten the screw (18) to 0,75 ± 0,07 m.dan. URGENT : Ensure that the gear selection control works properly in all the positions. There must be no additional travel of the lever when it is in position 2.
URGENT : Ensure that the precautions relating to safety and cleanliness are adhered to (refer to the brochure: RECOMMENDATIONS - PRECAUTIONS).
PAGE 1 - b1eg1xp0 - removing - refitting timing belt removing - refitting timing belt INJECTION ES9J4S URGENT Ensure that the precautions relating to safety and cleanliness are adhered to (refer to the
More information1 Recommended tools. removing - refitting : timing belt INJECTION ES9J4. PAGE 1 - b1eg1bp0 - removing - refitting : timing belt. - Fig.
PAGE 1 - b1eg1bp0 - removing - refitting timing belt removing - refitting timing belt INJECTION ES9J4 1 Recommended tools - Fig. 1 - [ 1 ] camshaft setting pegs (-).0187 B. - Fig. 2 - PAGE 2 - b1eg1bp0
More informationPRESENTATION : AL4 AUTOACTIVE AUTOMATIC GEARBOX... 1
GEARBOX PRESENTATION : AL4 AUTOACTIVE AUTOMATIC GEARBOX.................................... 1 1 General 1 2 Identification 2 3 Summary of operated components 5 4 Position : needle thrust bearings, friction
More information1. Rules to be respected
Page 1 of 9 REPAIRS : CLUTCH ACTUATOR 1. Rules to be respected Figure : B2BP051C 1.1. Prohibited operations Manipulating the clutch actuator via the push rod ( 1). Compressing and releasing the push rod
More informationREMOVAL - REFITTING : TIMING BELT ( SECOND ASSEMBLY
Page 1 of 9 REMOVAL - REFITTING : TIMING BELT ( SECOND ASSEMBLY ) : EW10J4S INJECTION OR INJECTION EW10J4 1. Special tools Figure : E5AP1J0C [1] camshaft hub setting rods (-).0189-A. Figure : E5AP27AC
More informationRepair Manual VW 02J gearbox. INA GearBOX
Repair Manual VW 02J gearbox INA GearBOX Special tools Pipe section, 50 mm: Press fitting of synchronizer body for third/fourth gear. Assembly of support bearing for input and output shaft. Part number:
More informationLuK Repair Solution for manual transmissions. Disassembly and assembly Special tool/failure diagnosis VW 02J
LuK Repair Solution for manual transmissions Disassembly and assembly Special tool/failure diagnosis VW 02J The content of this brochure shall not be legally binding and is for information purposes only.
More informationEngine, disassembly and
Page 1 of 13 13-1 Engine, disassembly and assembly Ribbed belt, removing and installing Removing - Remove noise insulation -arrows-. - Remove bumper Repair Manual, Body Exterior, Repair Group 63 - Move
More informationTiming Belt: Service and Repair Timing Belt Replacement
2003 Saturn Truck VUE V6-3.0L VIN B Copyright 2007, ALLDATA 9.50 Page 1 Timing Belt: Service and Repair Timing Belt Replacement Removal Procedure 1. Remove the front timing belt cover. 2. Rotate the crankshaft
More informationPlastic Trim Removal Tool Phillips Screwdriver (for vehicles w/ shift boot) Wire Cutter. (FOR VEHICLES w/o A SHIFT BOOT)
INSTALLATION INSTRUCTIONS C10FL0 DESCRIPTION: STI CVT SHIFT KNOB STI CVT SHIFT KNOB TOOLS REQUIRED: PARTS IDENTIFICATION: Plastic Trim Removal Tool Phillips Screwdriver (for vehicles w/ shift boot) Wire
More information1. Recommended tools.
C5 (X7) - B1BG012BP0 - Removing - Refitting : Engine/gearbox assembly : REMOVING - REFITTING : ENGINE/GEARBOX ASSEMBLY : Page 1 of 12 URGENT : Observe the safety and cleanliness instructions. URGENT :
More informationDirect Shift Gearbox (DSG) Mechatronic unit J743, removing and installing. - Loosen bolts - arrows - of oil pan - A - in diagonal sequence and remove.
- Loosen bolts - arrows - of oil pan - A - in diagonal sequence and remove. Note: Some transmission oil remains in the oil pan because not all of it can drain out. - Remove oil pan together with oil pan
More informationREMOVAL & INSTALLATION
REMOVAL & INSTALLATION Removal 1. Center steering wheel. Disconnect negative battery cable. Remove steering coupling shield (if equipped). Disconnect steering shaft at flexible coupling or pot joint. Note
More informationTechnical Note6019A X61, and TL4 - X77, and TL4 - X84, and TL4 - X85, and TL4 - X91, and TL4 - X95, and TL4 TL4 manual gearbox
Technical Note6019A X61, and TL4 - X77, and TL4 - X84, and TL4 - X85, and TL4 - X91, and TL4 - X95, and TL4 TL4 manual gearbox Edition 9 77 11 335 822 APRIL 2009 Edition Anglaise "The repair methods given
More information2 Transmission AUTOMATIC GEARBOX X45 23A
2 Transmission AUTOMATIC GEARBOX X45 NOVEMBER 2009 EDITION ANGLAISE "The repair procedures given by the manufacturer in this document are based on the technical specifications current when it was prepared.
More informationRemoving and installing toothed belt
Page 1 of 10 Special tools and workshop equipment required Diesel injection pump locking pin -3359- (2x) Pin wrench -T10020- Crankshaft stop -T10050- for engines with circular crankshaft sprocket Locking
More informationSERVICE MANUAL. Hydraulic Motors type MTM
SERVICE MANUAL Hydraulic Motors type MTM and Сервизно ръководство Демонтаж Хидравлични мотори Тип GW Dust Front Cap 2008 and Bearing Kit Dust Front Cap Ring 90x1,5 "C" and Bearing Kit Ring 90x1,5 "W" Dust
More informationVolkswagen New Beetle 2.0 Liter 4-cyl General, Engine (Engine Code AEG) 13 Engine-Crankshaft, Cylinder block (Page GR-13)
13 Engine-Crankshaft, Cylinder block (Page GR-13) Engine, disassembly and assembly 10-222 A/21 guide from 10-222 A support tool, modifying Ribbed belt, removing and installing Semi-automatic toothed belt
More information10/13/2018 Transmission/Transaxle Automatic - 41te Transmission Range Sensor Removal 2005 Chrysler PT Cruiser (2.
2005 PT Cruiser (2.4L) - PT REMOVAL Report a problem with this article The valve body assembly must be removed to gain access to and replace the transmission range sensor. 1. Disconnect the battery cables.
More information2003 Cadillac CTS V6-3.2L VIN N
1 of 16 5/11/2013 11:18 AM 2003 Cadillac CTS V6-3.2L VIN N Vehicle» Engine, Cooling and Exhaust» Engine» Timing Belt» Service and Repair» Timing Belt Replacement Timing Belt Replacement Tools Required
More information2857A Service 0422 S/Section
TECHNICAL NOTE Edition Anglaise ALL TYPES SEPTEMBER 1997 77 11 196 123 Type XXX X 2857A Service 0422 S/Section 13 13 REMOVAL - REFITTING THE HUB ON THE POWER ASSISTED STEERING PUMP Other sub-section concerned:
More information3/6/2017 Timing Chain Service and Repair, Removal and Replacement: Valve Timing, Installing and Adjusting
Valve timing, adjusting Special tools and equipment - T10068 Camshaft bar - T10069 Counter support - VAG 1331 Torque wrench (5-50 Nm) - VAG 1332 Torque wrench (40-200 Nm) - AMV 174 004 01 Sealing compound
More information57-1. Front door. Tools. Special tools and equipment. T Socket 3320/2 Bit insert for Socket T Assembly tool
57-1 Front door Tools Special tools and equipment T 10011 Socket 3320/2 Bit insert for 3320 3410 Socket T 10034 Assembly tool 57-2 Front door, assembly overview Note: The instrument panel must be removed
More informationBefore performing any on-vehicle adjustments to fuel or ignition systems, ensure engine mechanical condition is okay.
Page 1 of 11 ARTICLE BEGINNING INTRODUCTION Introduction information not applicable. ENGINE MECHANICAL Before performing any on-vehicle adjustments to fuel or ignition systems, ensure engine mechanical
More informationSealing flanges and flywheel/drive plate, removing and installing
Page 1 of 20 13-47 Sealing flanges and flywheel/drive plate, removing and installing Note: For repairs to the clutch: Repair Manual, 5 Spd. Manual Transmission 012/01W Front Wheel Drive, Repair Group 30
More informationDRIVE AXLE Volvo 960 DESCRIPTION & OPERATION AXLE IDENTIFICATION DRIVE AXLES Volvo Differentials & Axle Shafts
DRIVE AXLE 1994 Volvo 960 1994 DRIVE AXLES Volvo Differentials & Axle Shafts 960 DESCRIPTION & OPERATION All 960 station wagon models use type 1041 rear axle assembly. All 960 4-door models use type 1045
More informationModel 4360 Teardown and Reassembly Instructions
Clean the outside surface of the transaxle. Place the shifter in neutral position. Remove detent cover screw (item 3), detent cover (item 4), detent springs (item 5), and detent balls (item 6). Use a magnet
More informationDisassembling and assembling transmission
27-640 Disassembling and assembling transmission Preceding work: Removing and installing transmission with torque converter (27-600). Operation number of operation texts and operation values or standard
More informationD - ADJUSTMENTS - 4-CYL
D - ADJUSTMENTS - 4-CYL 1993 Toyota Celica 1993 ENGINE PERFORMANCE Toyota 4-Cylinder On-Vehicle Adjustments Celica ENGINE MECHANICAL Before performing any on-vehicle adjustments to fuel or ignition systems,
More informationTiming Belt: Service and Repair Timing Belt Replacement
2000 Cadillac Catera V6-3.0L VIN R Copyright 2006, ALLDATA 8.80 Page 1 Timing Belt: Service and Repair Timing Belt Replacement TIMING BELT REPLACEMENT Removal Procedure ^ Tools Required - J 42069 Timing
More informationSALES DIVISION NETWORK TECHNICAL INFORMATION WORKSHOP MANUAL MOTOR ENGINE
SALES DIVISION NETWORK TECHNICAL INFORMATION WORKSHOP MANUAL MOTOR ENGINE CONTENTS CHARACTERISTICS... 5 Engine markings... 5 TIGHTENING TORQUES... 5 SPECIAL TOOLS... 6 IDENTIFICATION... 7 Differences between
More informationAir Collet Closer - Upgrade - OL-1
LAST UPDATED: 11/26/2018 Air Collet Closer - Upgrade - OL-1 AD0062 Applies to machines built from: May, 2010 Introduction 1 This procedure tells you how to install the Office Lathe air collet closer (ACC)
More informationOperating and Maintenance Instructions for: Figure 79 Pneumatic Actuators (U/E options)
for: Figure 79 Pneumatic Actuators (U/E options) Introduction The Keystone Figure 79 Pneumatic Actuator range is available in three mounting options, as follows:- 79U - Keystone Mounting Standard 79E -
More informationSECTION G2: CABLE PROCESSOR MODULE MAINTENANCE
SECTION G2: CABLE PROCESSOR MODULE MAINTENANCE Cable Processor Module overview WARNING! When tipping the Cable Processor Module back, (after removing the toggle arm pin), use extreme caution not to drop
More informationChapter 5 Part B: Ignition system - transistorised type
5B 1 Chapter 5 Part B: Ignition system - transistorised type Contents Coil - testing........................................... 9 Distributor - overhaul..................................... 7 Distributor
More information2003 Volkswagen Passat GL
2001-03 AUTOMATIC TRANSMISSIONS Removal & Installation - 01V APPLICATION TRANSAXLE APPLICATION Application Transaxle Model Passat 1.8L (FWD) 01V 2.8L (FWD & 4WD) 01V 4.0L (AWD) 2002-03 01V REMOVAL & INSTALLATION
More informationKEYSTONE FIGURE 79 PNEUMATIC ACTUATOR OPERATING AND MAINTENANCE INSTRUCTIONS
Operating and Maintenance Instructions for: Figure 79 Pneumatic Actuators (U/E options) Double Acting Actuator 4. If pipelines are hydraulically tested, then the lines should be blown down with high pressure
More informationSERVICE MANUAL. Chairman HD3
SERVICE MANUAL Chairman HD3 US How to contact Permobil Head Office of the Permobil group Produced and published by Permobil AB, Sweden Edition no.3, 2009-08 Article no.: 201161-US-0 Contents Contents
More informationModels Affected: Certain 2013 Model Year Propane Vision Buses Equipped with Ford 6.8L Engines CORRECTIVE ACTION ---- PROCEDURE
Models Affected: Certain 2013 Model Year Propane Vision Buses Equipped with Ford 6.8L Engines ISSUE Certain 2013 model year propane Vision buses equipped with Ford 6.8L engines may not have the service
More informationChrysler 200 LX (with a 3.0 screen) 2015-up Jeep Cherokee Sport 2014-up Ram Trucks (without 8.4 inch touchscreen) 2013-up B
Installation instructions for 99-6518B Chrysler 200 LX (with a 3.0 screen) 2015-up Jeep Cherokee Sport 2014-up Ram Trucks (without 8.4 inch touchscreen) 2013-up 99-6518B KIT FEATURES ISO DIN radio provision
More informationCALIFORNIA TRIMMER MOWER MAINTENANCE MANUAL
CALIFORNIA TRIMMER MOWER MAINTENANCE MANUAL 2 Table of Contents Section 1: General Information Page Handle Assembly Instructions 4 Maintenance All Models 6 Oil Change Procedures All Models 9 Height Adjustment
More informationOil pan, oil strainer and valve body, removing and installing
Page 1 of 44 38-1 Oil pan, oil strainer and valve body, removing and installing WARNING! Do not run engine with the oil pan removed or without ATF filling and do not tow vehicle. Notes: Always replace
More informationDismantling and assembling transmission
27-640 Dismantling and assembling transmission Operation number of the operation texts and work units or standard texts and flat rates: 27-4010 P27-5367-61 Control pressure cable (98) Slacken, remove and
More informationSERVICE MANUAL. Chairman
SERVICE MANUAL Chairman US How to contact Permobil Permobil Inc. USA 6961 Eastgate Blvd. Lebanon, TN 37090 USA Phone: 800-736-0925 Fax: 800-231-3256 Email: info@permobilusa.com Head Office of the Permobil
More informationKJ JEEP COMBINATION BULL BAR WARNING
KJ JEEP COMBINATION BULL BAR PRODUCT NUMBER FITTING KIT NUMBER 3450120 6171962 WARNING FOR VEHICLES EQUIPPED WITH SRS AIRBAG WHEN INSTALLED IN ACCORDANCE WITH THESE INSTRUCTIONS, THE FRONT PROTECTION BAR
More informationMax IV Rear Axle Replacement For models after Serial Number and all rear splined axle replacements.
Max IV Rear Axle Replacement For models after Serial Number 19089 and all rear splined axle replacements. 10/8/03 Max IV Snap Ring Rear Axle replacement.doc Tools required: 9/16 Wrench 6 Extension Steel
More information(a) Remove the rear floor service hole cover. (b) Disconnect the fuel pump connector.
REMOVAL 1. REMOVE REAR SEAT CUSHION ASSEMBLY 2. REMOVE REAR FLOOR SERVICE HOLE COVER (a) Remove the rear floor service hole cover. (b) Disconnect the fuel pump connector. 3. DISCHARGE FUEL SYSTEM PRESSURE
More information2001 Ford FOCUS. Submodel: ZTS Engine Type: L4 Liters: 2.0 Fuel Delivery: FI Fuel: GAS. Timing Belt
2001 Ford FOCUS Submodel: ZTS Engine Type: L4 Liters: 2.0 Fuel Delivery: FI Fuel: GAS SECTION 303-01A: Engine??? 2.0L Zetec-E (Zetec) 2001 Focus Workshop Manual IN-VEHICLE REPAIR Procedure revision date:
More informationFord Mustang CH
Installation instructions for part KIT FEATURES DIN radio provision with pocket ISO DIN radio provision with pocket Double DIN radio provision Painted charcoal to match factory dash Ford Mustang 2010-2014
More informationTOYOTA SIENNA XM SATELLITE RADIO Preparation
Preparation Part Number: Mounting Kit: PT546-08070 Tuner Assy: 86180-0W031 Tuner Assy Kit Contents (86180-0W031) Item # Quantity Reqd. Description 1 1 Tuner Assy, Stereo Component Mounting Kit Contents
More informationSERVICE MANUAL OF SERVOMOTORS HD/HR RANGE
SERVICE MANUAL HD/HR RANGE OF SERVOMOTORS ISSUE 2 WARNING Servomotors contain magnetic material which will attract metal particles. Care should be taken when dismantling motors to avoid this. All D.C.
More informationADJUSTMENTS Mazda MX-3. Fig. 1: Identifying Engine Code & Number Courtesy of MAZDA MOTORS CORP. VALVE CLEARANCE ADJUSTMENT
Fig. 1: Identifying Engine Code & Number Courtesy of MAZDA MOTORS CORP. ADJUSTMENTS VALVE CLEARANCE ADJUSTMENT 1. No valve clearance adjustment is required, as hydraulic valve lash adjusters are used.
More informationRemoving and installing dash panel insert
Removing and installing dash panel insert Caution To disconnect and connect the battery, the procedure described in the workshop manual should be strictly adhered to Chapter. Note Pull off multi-pin connector
More information1993 ACCESSORIES & EQUIPMENT Volkswagen Power Sun Roof. Volkswagen; Corrado SLC, EuroVan, Golf, GTI, Jetta, Passat
Article Text ARTICLE BEGINNING 1993 ACCESSORIES & EQUIPMENT Volkswagen Power Sun Roof Volkswagen; Corrado SLC, EuroVan, Golf, GTI, Jetta, Passat DESCRIPTION & OPERATION The power sun roof operates at all
More informationOperator's manual. TruTool F 140 (1A1) english
Operator's manual TruTool F 140 (1A1) english Table of contents 1. Safety...3 2. Description...5 2.1 Intended use...6 2.2 Technical data of the TruTool F 140...7 2.3 Lock seams...8 3. Tool assembly...10
More informationChapter 4 Part C: Fuel and exhaust systems - multi-point fuel injection models
4C 1 Chapter 4 Part C: Fuel and exhaust systems - multi-point fuel injection models Contents ACAV intake system (1998 cc 16-valve models) - general information, 19 Accelerator cable - removal, refitting
More informationWheel Changing ! WARNING: Spare Wheel Location
Spare Wheel Location Be prepared for a flat tyre. Know where equipment is stowed and read the wheel changing and jacking instructions carefully. Pull off the road completely, clear of all traffic and park
More informationSeat belts. Safety precautions for handling pyrotechnic seat belt tensioners WARNING!
Page 1 of 41 69-1 Seat belts Safety precautions for handling pyrotechnic seat belt tensioners WARNING! Testing, removing, installing and repair work must only be carried out by properly qualified personnel.
More informationSection X STEERING DATA AND SPECIFICATIONS. 21 degrees 45 minutes -f- or 1 degree (inner wheel when outer wheel is 20 degrees)
76 Section X DATA AND SPECIFICATIONS MODELS MC-1 MG-2 MC-3 MY-1 Steering Type Manual Power Worm and Three Tooth Roller None None None Rack and Gear Sector, Recirculating Ball Nut Ratio Manual 20.4... Power
More informationREMOVAL & INSTALLATION
REMOVAL & INSTALLATION CAUTION: This application is an interference engine. Do not rotate camshaft or crankshaft when timing belt is removed, or engine damage may occur. TIMING BELT Removal 1. Disconnect
More informationDouble Offset High Performance Butterfly Valve
Double Offset High Performance Butterfly Valve INSTALLATION OPERATION MAINTENANCE APOLLO INTERNATIONAL HIGH PERFORMANCE BFV IOM - Page 2 of 20 TABLE OF CONTENTS INTRODUCTION 3 PRODUCT STORAGE 3 PRODUCT
More informationEngine timing tools. VAG TFSi FSi K 10548
Engine timing tools VAG TFSi FSi 2.0 K 10548 www.kamasatools.com Plan Layout A D B E F C Component Identification Ref Oem Ref. Description A T10020 Tension Wrench B T40011 Tensioner Pin C T10252 Camshaft
More informationPolaris 340 & ATV Power Module Training and Troubleshooting Guide
Polaris 340 & ATV Power Module Training and Troubleshooting Guide Summary: This guide is intended as a training tool for the mechanical evaluation and troubleshooting of a 340 or ATV power module only.
More informationFE 35, 40, 55, EC Every time you open the housing, clean the motor with a soft brush.
FE 35, 40, 55, EC 70 1 Service Manual FE 35, FE 40, FE 55 Electric Trimmers, EC 70 Electric Edger As the design concept of the FE 35 and FE 40 trimmers is almost identical, the descriptions and servicing
More informationCentral Hydraulics, Inc. Stocking Distributor for White Hydraulic motors
whitedriveproducts PI444200 Rev. 2.06 SERVICE INSTRUCTIONS FOR THE CE [400 & 401] SERIES MOTORS For Use With Seal Kit: 400444200 dimensions: mm [in] A) B) C) Remove all shaft components from the shaft,
More informationSERVICE MANUAL STEERING AND RIGID DRIVE AXLES SERIES 068. Date Revision Description Owner 06/10/ Document emission PM
SERVICE MANUAL STEERING AND RIGID DRIVE AXLES SERIES 068 Date Revision Description Owner 06/10/09 1.0 Document emission PM COMER INDUSTRIES Axles & Wheel Drive Units Via Magellano, 37-42046 Reggiolo (RE)
More information1989 Jeep Cherokee. STEERING COLUMN' '1989 STEERING Jeep Steering Columns STEERING COLUMN STEERING Jeep Steering Columns
STEERING COLUMN 1989 STEERING Jeep Steering Columns DESCRIPTION All models use collapsible steering columns. All columns have integral ignition switch and locking device. Optional tilt wheel is available
More informationANTI-LOCK BRAKE SYSTEM - REAR WHEEL
ANTI-LOCK BRAKE SYSTEM - REAR WHEEL 1994 Nissan Pickup 1994 BRAKES Nissan - Rear Anti-Lock Pathfinder, Pickup DESCRIPTION In 2WD mode, Rear Anti-Lock Brake System (RABS) helps the driver to maintain steering
More informationINSTRUCTIONS. Disassembly. Shifter Cam Assembly. Shifter Forks
INSTRUCTIONS Disassembly To protect against accidental start-up of vehicle, always disconnect the negative battery cable before working on the motorcycle. Failure to disconnect the battery cable could
More information1ZSC ABH en, Rev. 1. Motor-drive mechanisms, types BUE and BUL2 Maintenance guide
1ZSC000498-ABH en, Rev. 1 Motor-drive mechanisms, types BUE and BUL2 Maintenance guide Original instruction The information provided in this document is intended to be general and does not cover all possible
More informationTrim (general) Lower A-pillar trim, removing and installing
Page 1 of 16 70-72 Trim (general) Lower A-pillar trim, removing and installing - To remove, remove A-pillar bolts 4 (2x). Tightening torque: 1.5 Nm (13 in. lb) - Remove door seal -2- in area of A-pillar
More informationFig.01 Fig.02 Fig.03. Disassembly & Reassembly Instructions SBV-HP - Page 3
M12A14 WITH FLOATING BACKSEAT 3 Fig.01 Fig.02 Fig.03 Disassembly & Reassembly Instructions SBV-HP - Page 3 M12A14 WITH FLOATING BACKSEAT 3 1. Caution, before any attempt is made to disassemble, verify
More informationRaptor V/R (all models) SIMPLE BELT REPLACEMENT METHOD Updated: 01/03/2013
Raptor V/R (all models) SIMPLE BELT REPLACEMENT METHOD Updated: 01/03/2013 The use of the information in this document does not infer that the person/company/business who receives it has any authority
More informationHT125KM, FA3TM, FA6TE
HT125KM, FA3TM, FA6TE FLANGE ALIGNMENT TOOLS Operator Instruction Manual info@equalizerinternational.com www.equalizerinternational.com INNOVATION IN ITS MOST FUNCTIONAL FORM INDEX SECTION CONTENTS PAGE
More informationIt is strongly recommended that this kit be installed by an authorized Polaris dealer.
EPS STEERING KIT P/N 2879970 APPLICATION RANGER 570 AND RANGER ETX IMPORTANT It is strongly recommended that this kit be installed by an authorized Polaris dealer. BEFORE YOU BEGIN Read these instructions
More informationAIR INDUCTION SYSTEM
Page 1 PART NUMBER: APPLICATION: 203.51.2500 HONKER C5 1997 2000 CORVETTE AIR INDUCTION SYSTEM (without supercharger) INSTRUCTION SHEET NUMBER: 903.51.9850G PACKAGE CONTENTS: Air Box Cover Air Box Base
More informationNissan 370Z 2009-up (without navigation) B
REV. 4/2/2014 INST99-7607B INSTALLATION INSTRUCTIONS FOR PART 99-7607B KIT FEATURES DIN radio provision with pocket ISO radio provision with pocket Double DIN radio provision Painted matte black to match
More informationEquipped with AEM Dryflow Filter No Oil Required! INSTALLATION INSTRUCTIONS PART NUMBER C (GUN METAL GRAY FINISH) NISSAN SENTRA 1.
Equipped with AEM Dryflow Filter No Oil Required! INSTALLATION INSTRUCTIONS PART NUMBER 21-799C (GUN METAL GRAY FINISH) 2014-16 NISSAN SENTRA 1.8L 1 ITEM NO. PART NUMBER DESCRIPTION QTY. 1 21-2157D AIR
More informationPART NO. K305. Engine Timing Tools. Ford 1.6 Ti-VCT 1.8 TDi/TDCi 2.0 TDCi.
PART NO. K305 Engine Timing Tools Ford 1.6 Ti-VCT 1.8 TDi/TDCi 2.0 TDCi www.kamasatools.com Plan Layout Component Identification Part No OEM Ref Description Identification A 23054-05 303-748 Crankshaft
More informationAutomatic Transmission 5R44E and 5R55E
307-01-1 Automatic Transmission 5R44E and 5R55E 307-01-1 IN-VEHICLE REPAIR Main Control Valve Body Special Tool(s) Aligner, Valve Body 307-333 (T95L-70010-B) Aligner, Valve Body 307-334 (T95L-70010-C)
More informationTIMING BELT REPLACEMENT. Tools Required. J A (KM-421-A) Timing Belt Adjuster J Angle Meter KM-470-B Angular Torque Gage
Page 1 of 20 TIMING BELT REPLACEMENT Tools Required J 42492-A (KM-421-A) Timing Belt Adjuster J 45059 Angle Meter KM-470-B Angular Torque Gage Removal Procedure Fig. 37: View Of Throttle Cable CAUTION:
More informationBMW N54 TWIN TURBO THROTTLE BODY HARD PIPE INSTALLATION INSTRUCTIONS
BMW N54 TWIN TURBO THROTTLE BODY HARD PIPE INSTALLATION INSTRUCTIONS Tools needed: Short flat blade screwdriver T20, T25 Torxs 14mm spanner Needle nosed pliers 7mm hose clamp driver Safety eyewear, footwear,
More information2005 Chevrolet Optra (CANADA) L4-2.0L
1 of 13 9/28/2013 7:54 PM 2005 Chevrolet Optra (CANADA) L4-2.0L Vehicle» Engine, Cooling and Exhaust» Engine» Timing Belt» Service and Repair Timing Belt Replacement Removal Procedure Caution: Refer to
More informationLuggage System Fitting Instructions - Sprint ST
WARNING: Always have Triumph approved parts, accessories and conversions fitted by a trained technician of an authorised Triumph dealer. The fitting of parts, accessories and conversions by a technician
More informationEnglish. Fitting Instructions: America and Speedmaster A with A , A or A of 10 A Parts Supplied A :
English Fitting Instructions: America and Speedmaster A977800 with A9778007, A975857 or A975858 Thank you for choosing this Triumph genuine accessory kit. This accessory kit is the product of Triumph's
More informationService Manual. LT-5 Lawn Tractor
Service Manual LT-5 Lawn Tractor NOTE: These materials are for use by trained technicians who are experienced in the service and repair of outdoor power equipment of the kind described in this publication,
More information1. Disconnect negative battery cable. 2. Remove upper and lower front timing belt covers..
BELT AND SPROCKETS-TIMING REMOVAL TIMING BELT Zoom 1. Disconnect negative battery cable. 2. Remove upper and lower front timing belt covers.. CAUTION: When aligning crankshaft and camshaft timing marks
More informationRemove Air Cleaner Cover and. Filter
Remove Air Cleaner Cover and Inspect paper filter for tears Foam pre-cleaner is washable if equipped Replace if necessary Filter Remove Trim Panel Pull throttle lever knob off Remove 3, 8mm screws Remove
More informationTiming Belt Replacement
Timing Belt Replacement Tools Required Timing Belt Alignment Kit Crank Hub TORX Socket Removal Procedure 1. Disconnect the negative battery cable. 2. Remove the timing belt front cover. 3. Rotate the crankshaft
More information2003 Jaguar X-Type BRAKES' 'Disc - X-Type
REAR DISC BRAKE CALIPER WARNING: Brake dust, if inhaled can damage your health. Always remove brake dust using a vacuum brush. Do not use a compressed air line to disperse brake dust into the atmosphere.
More informationSTEERING SYSTEM PRECAUTION SR 1
System Name Power Window Control System STEERING COLUMN STEERING SYSTEM STEERING SYSTEM PRECAUTION 1 1. HANDLING PRECAUTIONS FOR S AIRBAG SYSTEM (SEE PAGE RS-1) 2. HANDLING PRECAUTIONS FOR STEERING COLUMN
More informationREMOVAL & INSTALLATION
REMOVAL & INSTALLATION TIMING BELT Removal (Esteem) 1. Disconnect negative battery cable. Remove right side engine under cover. Remove power steering and A/C compressor drive belts. 2. Remove A/C compressor
More informationTIMING BELT REPLACEMENT. Removal Procedure. Tools Required J Timing Belt Alignment Kit J Crank Hub Torx Socket
1 of 15 3/19/2012 5:34 PM TIMING BELT REPLACEMENT Removal Procedure Tools Required J 42069 Timing Belt Alignment Kit J 42098 Crank Hub Torx Socket Notice: Failure to follow the described timing belt inspection
More informationALLDATA Online Ford Focus L4-2.0L DOHC VIN 5 - Service and Repair. Service and Repair
Page 1 of 22 Service and Repair NOTE: Ford does not provide camshaft gear timing marks, or information to perform timing belt service without the special tools shown in this procedure. Timing Belt Special
More informationModels Affected: Certain 2014 Model Year Vision Buses Equipped with Ford 6.8L Propane Engines ISSUE
R E C A L L C A M P A I G N ----R 1 3 W G -- Adjustment Inspection ISSUE CORRECTIVE ACTION ---- Models Affected: Certain 2014 Model Year Vision Buses Equipped with Ford 6.8L Propane Engines On affected
More informationINSTALLATION INSTRUCTIONS PART NUMBER AEM C (GUN METAL GRAY FINISH)
Equipped with AEM Dryflow Filter No Oil Required! INSTALLATION INSTRUCTIONS PART NUMBER AEM-21-805C (GUN METAL GRAY FINISH) 2016.5-17 CHEVROLET CRUZE 1.4T ITEM NO. PART NUMBER DESCRIPTION QTY. 1 21-2038DK
More informationLOW RANGE OFF-ROAD Suzuki Samurai Venturi Vent Tube Nozzle (SKU# SER-VENT) Installation Instructions
86-88 Suzuki Samurai Venturi Vent Tube Nozzle (SKU# SER-VENT) Installation Instructions For a video of this procedure click HERE, or go to our web site. Suggested Tools: CAUTION: Safety glasses should
More information5 Mechanisms and accessories
5 Mechanisms and accessories 51A SIDE OPENING ELEMENT MECHANISMS 52A NON-SIDE OPENING ELEMENT MECHANISMS 54A WINDOWS 55A EXTERIOR PROTECTION 56A EXTERIOR ACCESSORIES 57A INTERIOR ACCESSORIES 59A SAFETY
More informationPAPER SHREDDER S16 PAPER SHREDDER S16 ILLUSTRATED PARTS LIST AND SERVICE INSTRUCTIONS
PAPER SHREDDER S16 PAPER SHREDDER S16 ILLUSTRATED PARTS LIST AND ISSUE 2 08/08/2002 PAPER SHREDDER INDEX S16 CONTENTS HEADING SECTION PREFACE AND INDEX INDEX ILLUSTRATED PARTS LIST 1 INSTALLATION 2 2 MODEL
More informationTOYOTA 4 RUNNER 2010-UP
INSTALLATION INSTRUCTIONS FOR PART 99-8227S KIT FEATURES KIT COMPONENTS APPLICATIONS TOYOTA 4 RUNNER 2010-UP U.S. PATENT # D639,292 99-8227S DIN Head unit provisions with pocket ISO DIN Head unit provision
More information