Aspects of Permanent Magnet Machine Design
|
|
- Loreen Evans
- 6 years ago
- Views:
Transcription
1 Aspects of Permanent Magnet Machine Design Christine Ross February 7, 2011 Grainger Center for Electric Machinery and Electromechanics
2 Outline Permanent Magnet (PM) Machine Fundamentals Motivation and Application Design Aspects PM Material PM Rotor Configurations Manufacturing Processes Design Tools 2
3 Permanent Magnet (PM) Machine Fundamentals Focus on electronically controlled PM AC synchronous machines Rotor magnetic field is supplied by PMs Stator windings are sinusoidally distributed windings, excited by sine-wave currents Brushless DC machines can also use PMs 3-phase stator windings Laminated stator 4-pole PM rotor Cross-section of surface-mounted PM machine 3
4 PM Machine Theory Output torque is proportional to power Control instantaneous torque by controlling magnitude of phase currents N f 60 RPM p speed N in RPM supply frequency f number of pole pairs p T P rm output torque T output power P rotor speed rm in rad/s 4
5 PM Machine Control Instantaneous torque control Servo performance kw Fast dynamic response Smooth output torque Accurate rotor position sensor information needed Back-emf e ωrm Single-phase equivalent circuit 5
6 PM Machine Control Flux-weakening control Constant power drives Traction, washing machines, starter/alternators Require constant output power over a speed range To operate above rated speed while maintaining rated terminal voltage, reduce flux by controlling magnetizing current T Iarm V [1] Soong Ideal flux-weakening characteristics torque T magnetic flux armature current Iarm terminal voltage V magnetic flux angular speed in rad/s 6
7 Motivation for PM Machine Motivation for PM machines: High efficiency (at full load) High power density Simple variable-frequency control Rotor excited without current No rotor conductor loss and heat Magnet eddy current loss is lower than iron loss and rotor cage loss 7
8 PM Machine Disadvantages Magnet cost New magnet manufacturing processes Magnet sensitivity to temperature and demagnetization Little control of magnet field Always have no-load spinning losses Without control, over speed means over voltage fault management issues 8
9 PM Machine Applications AC PM machines Servo control systems Precision machine tools IPM washing-machines, air conditioning compressors, hybrid vehicle traction DC PM machines Lower cost variable-speed applications where smoothest output torque is not required Computer fans, disk drives, actuators Industrial applications where constant speed is necessary IPM washing-machine motors [5] Hendershot and Miller 9
10 Design Specifications Electrical Environmental Ambient temperature Cooling system Structure Vibration Mechanical outputs Torque Speed Power Key features of machines Flux linkage Saliency, inductances Assembly process Magnet cost Number of magnets Simplicity of design Field weakening Reluctance torque Field control Line start, no inverter 10
11 PM Material Soft magnetic material (steel) small B-H loop Hard magnetic material (PM) large B-H loop Remnant Flux Density B r Coercivity H c Choose magnets based on high B r and H c 11
12 PM Material PM B r (T) H c (ka/m) Cost Resistivity (µω-cm) Max. Working Temp. (ºC) Alnico > 500 Curie Temp. (ºC) Ferrite low >10, NdFeB (sintered) Sm 2 Co 7 (sintered) medium Higher than NdFeB [2] Miller [3] Hendershot and Miller Arnold Magnetics
13 PM Material Chinese dependency No shortage Mountain Pass, CA Idaho Nd is about as common as Cu Arnold Magnetic Technologies 13
14 PM Machine Rotor Configurations Surface-mounted PM rotor Maximum magnet flux linkage with stator Simple, robust, manufacturable For low speeds, magnets are bonded to hub of soft magnetic steel Higher speeds use a retaining sleeve Inset better protection against demagnetization; wider speed range using flux-weakening; increases saliency; but also increases leakage Inset magnets Surface bread-loaf magnets 14
15 PM Machine Rotor Configurations Interior-mounted PM (IPM) rotor IPM Advantages Extended speed range with lower loss Increases saliency and reluctance torque Greater field weakening capability A. O. Smith 15
16 PM Machine Topology SMPM: More mechanically robust Magnet losses can be an issue (not shielded by rotor iron); reduce by segmenting magnets axially or radially or increasing magnet resistivity IPM: Better demagnetization withstand Characteristic SMPM IPM Saliency No Yes Field Weakening Some Good Controller Standard More Complex [4] Klontz and Soong 16
17 PM Manufacturing Practices Realistic manufacturing tolerances Key parameters stator inner diameter, rotor outer diameter, no load current, winding temperature Issues with core steels laser cutting, punched laminations, lamination thickness Issues with magnets dimensions, loss of strength due to thermal conditioning Hybrid Camry PM synchronous AC motor/generator ecee.colorado.edu High speed practice and limits rotor diameter limits speed 17
18 PM Machine Design Process Design and simulate motor and driver Separately Combined Analytical, lumped-circuit, and finite-element design tools Different tools are used to trade-off understanding of the design, speed, and accuracy Finite element meshing, flux lines and B for SMPM machine A.O. Smith 18
19 Analytical Design Tools Broad simplifying approximations Equivalent circuit parameters Use for initial sizing and performance estimates Performance prediction Limitations Does not initially account for local saturation Requires tuning with FE results 19
20 Analytical Design Tools Core losses Hysteresis loss Eddy current loss Anomalous loss depends on material process, impurities Problems with core loss prediction Stator iron loss: based on knowledge of stator tooth flux density waveforms Usually assumes sinusoidal time-variation and one-dimensional spatial variation Flux waveforms have harmonic frequency and rotational component Use db/dt method for eddy-current term, frequency spectrum method Torque, efficiency, inductance [4] Klontz and Soong 20
21 Lumped-Circuit Design Tools Non-linear magnetic material modeling of simple geometries Need a good understanding of magnetic field distribution to partition Fast to solve, good for optimization Limitations Requires tuning with FE results Lovelace, Jahns, and Lang 21
22 Finite-Element Modeling and Simulation Tools Important aspects model saturation More accurate Essential when saturation is significant Limitations Meshing Only as accurate as model design 2D, 3D Not currently used as a design tool due to computational intensity y (m) Average Magnitude Magnetic Flux Density linear run x (m) Nonlinear magnetostatic FE average magnetic flux density solution for machine with solid rotor
23 Ideal Design Tool Easy to set up Models all significant aspects of machine that affect performance magnetic saturation Efficiently simulates transient conditions and steady-state operation 23
24 References [1] W.L. Soong, Design and Modeling of Axially-Laminated Interior Permanent Magnet Motor Drives for Field-Weakening Applications, Ph.D. Thesis, School of Electrical and Electronic Engineering, University of Glasgow, [2] T.J.E. Miller, Brushless Permanent-Magnet and Reluctance Motor Drives, Oxford Science Publications, [3] J.R. Hendershot and T.J.E. Miller, Design of Brushless Permanent-Magnet Motors, Magna Physics Publishing and Oxford University Press, [4] K. Klontz and W.L. Soong, Design of Interior Permanent Magnet and Brushless DC Machines Taking Theory to Practice course notes [5] J.R. Hendershot and T.J.E. Miller, Design of Brushless Permanent-Magnet Motors, Motor Design Books, Questions? 24
Design of Brushless Permanent-Magnet Machines. J.R. Hendershot Jr. T.J.E. Miller
Design of Brushless Permanent-Magnet Machines J.R. Hendershot Jr. T.J.E. Miller Contents 1 GENERAL INTRODUCTION l 1.1 Definitions and types of brushless motor 1 1.2 Commutation,. 4 1.3 Operation of 3-phase
More informationAXIAL FLUX PERMANENT MAGNET BRUSHLESS MACHINES
AXIAL FLUX PERMANENT MAGNET BRUSHLESS MACHINES Jacek F. Gieras, Rong-Jie Wang and Maarten J. Kamper Kluwer Academic Publishers, Boston-Dordrecht-London, 2004 TABLE OF CONTENETS page Preface v 1. Introduction
More informationBonded versus Sintered Interior PM Motor for Electric and Hybrid Vehicles
! "# " Bonded versus Sintered Interior PM Motor for Electric and Hybrid Vehicles A. FONSECA and Ch. CHILLET ICEM 2002, Brugge, Belgium, August 2002 $ # Objective Comparison of Bonded and Sintered IPM Motor
More informationUniversity of L Aquila. Permanent Magnet-assisted Synchronous Reluctance Motors for Electric Vehicle applications
University of L Aquila Department of Industrial and Information Engineering and Economics Permanent Magnet-assisted Synchronous Reluctance Motors for Electric Vehicle applications A. Ometto, F. Parasiliti,
More informationAxial Flux Permanent Magnet Brushless Machines
Jacek F. Gieras Rong-Jie Wang Maarten J. Kamper Axial Flux Permanent Magnet Brushless Machines Second Edition Springer Contents 1 Introduction 1 1.1 Scope 1 1.2 Features 1 1.3 Development of AFPM Machines
More informationGeneral Purpose Permanent Magnet Motor Drive without Speed and Position Sensor
General Purpose Permanent Magnet Motor Drive without Speed and Position Sensor Jun Kang, PhD Yaskawa Electric America, Inc. 1. Power consumption by electric motors Fig.1 Yaskawa V1000 Drive and a PM motor
More informationHigh Performance Machine Design Considerations
High Performance Machine Design Considerations High Performance Machine Design Considerations Abstract From Formula One race cars to consumer vehicles, the demand for high performing, energy efficient
More informationPermanent Magnet Machines for Distributed Generation: A Review
Permanent Magnet Machines for Distributed Generation: A Review Paper Number: 07GM0593 Authors: Tze-Fun Chan, EE Department, The Hong Kong Polytechnic University, Hong Kong, China Loi Lei Lai, School of
More informationBrushless dc motor (BLDC) BLDC motor control & drives
Brushless dc motor (BLDC) BLDC motor control & drives Asst. Prof. Dr. Mongkol Konghirun Department of Electrical Engineering King Mongkut s University of Technology Thonburi Contents Brushless dc (BLDC)
More informationCHAPTER 3 DESIGN OF THE LIMITED ANGLE BRUSHLESS TORQUE MOTOR
33 CHAPTER 3 DESIGN OF THE LIMITED ANGLE BRUSHLESS TORQUE MOTOR 3.1 INTRODUCTION This chapter presents the design of frameless Limited Angle Brushless Torque motor. The armature is wound with toroidal
More informationCHAPTER 1 INTRODUCTION
1 CHAPTER 1 INTRODUCTION 1.1 ELECTRICAL MOTOR This thesis address the performance analysis of brushless dc (BLDC) motor having new winding method in the stator for reliability requirement of electromechanical
More informationQUESTION BANK SPECIAL ELECTRICAL MACHINES
SEVENTH SEMESTER EEE QUESTION BANK SPECIAL ELECTRICAL MACHINES TWO MARK QUESTIONS 1. What is a synchronous reluctance 2. What are the types of rotor in synchronous reluctance 3. Mention some applications
More informationDevelopment of High-Speed AC Servo Motor
1 / 5 SANYO DENKI TECHNICAL REPORT No.11 May-2001 Feature Development of High-Speed AC Servo Motor Shintarou Koichi Koujirou Kawagishi Satoru Onodera 1. Introduction Higher speed and higher acceleration
More informationCOLLEGE OF ENGINEERING DEPARTMENT OF ELECTRICAL AND ELECTRONICS ENGINEERING QUESTION BANK SUBJECT CODE & NAME : EE 1001 SPECIAL ELECTRICAL MACHINES
KINGS COLLEGE OF ENGINEERING DEPARTMENT OF ELECTRICAL AND ELECTRONICS ENGINEERING QUESTION BANK SUBJECT CODE & NAME : EE 1001 SPECIAL ELECTRICAL MACHINES YEAR / SEM : IV / VII UNIT I SYNCHRONOUS RELUCTANCE
More informationComparison of IPM and SPM motors using ferrite magnets for low-voltage traction systems
EVS28 KINTEX, Korea, May 3-6, 215 Comparison of IPM and SPM motors using ferrite magnets for low-voltage traction systems Yong-Hoon Kim 1, Suwoong Lee 1, Eui-Chun Lee 1, Bo Ram Cho 1 and Soon-O Kwon 1
More informationPermanent Magnet Synchronous Motor. High Efficiency Industrial Motors
VoltPro is a new industrial motor range to meet high efficiency needs of industry by higher level of IE4 efficiency class. Main advantage of this product is cost effective solution ensured by using standard
More informationCHAPTER 5 ANALYSIS OF COGGING TORQUE
95 CHAPTER 5 ANALYSIS OF COGGING TORQUE 5.1 INTRODUCTION In modern era of technology, permanent magnet AC and DC motors are widely used in many industrial applications. For such motors, it has been a challenge
More informationCHAPTER 2 MODELLING OF SWITCHED RELUCTANCE MOTORS
9 CHAPTER 2 MODELLING OF SWITCHED RELUCTANCE MOTORS 2.1 INTRODUCTION The Switched Reluctance Motor (SRM) has a simple design with a rotor without windings and a stator with windings located at the poles.
More informationUniversity of New South Wales School of Electrical Engineering & Telecommunications ELEC ELECTRIC DRIVE SYSTEMS.
Aims of this course University of New South Wales School of Electrical Engineering & Telecommunications ELEC4613 - ELECTRIC DRIVE SYSTEMS Course Outline The aim of this course is to equip students with
More informationDHANALAKSHMI SRINIVASAN COLLEGE OF ENGINEERING AND TECHNOLOGY MAMALLAPURAM, CHENNAI
DHANALAKSHMI SRINIVASAN COLLEGE OF ENGINEERING AND TECHNOLOGY MAMALLAPURAM, CHENNAI -603104 DEPARTMENT OF ELECTRICAL AND ELECTRONICS ENGINEERING QUESTION BANK VII SEMESTER EE6501-Power system Analysis
More informationThermal Analysis of Electric Machines Motor-CAD
Thermal Analysis of Electric Machines Motor-CAD Create, Design, Engineer! Brief Look at MotorCAD geometry input using dedicated editors select materials, cooling options All difficult heat transfer data
More informationPermanent magnet machines and actuators
Permanent magnet machines and actuators Geraint Jewell The University of Sheffield Symposium on Materials for a Sustainable Future 11/09/09 1 Key PM Properties for Electro-Mechanical Devices High remanence
More informationB.E-EEE(Marine) Batch 7. Subject Code EE1704 Subject Name Special Electrical Machines
Course B.E-EEE(Marine) Batch 7 Semester VII Subject Code EE1704 Subject Name Special Electrical Machines Part-A Unit-1 1 List the applications of synchronous reluctance motors. 2 Draw the voltage and torque
More informationDesign and Analysis of Radial Flux Permanent Magnet Brushless DC Motor for Gearless Elevators
International Journal of Control Theory and Applications ISSN : 0974-5572 International Science Press Volume 9 Number 43 2016 Design and Analysis of Radial Flux Permanent Magnet Brushless DC Motor for
More informationQuestion Bank ( ODD)
Programme : B.E Question Bank (2016-2017ODD) Subject Semester / Branch : EE 6703 SPECIAL ELECTRICAL MACHINES : VII-EEE UNIT - 1 PART A 1. List the applications of synchronous reluctance motors. 2. Draw
More informationDESIGN OF COMPACT PERMANENT-MAGNET SYNCHRONOUS MOTORS WITH CONCENTRATED WINDINGS
DESIGN OF COMPACT PERMANENT-MAGNET SYNCHRONOUS MOTORS WITH CONCENTRATED WINDINGS CSABA DEAK, ANDREAS BINDER Key words: Synchronous motor, Permanent magnet, Concentrated winding. The design and comparison
More informationChapter 1 INTRODUCTION. 1.1 Scope. 1.2 Features
Chapter 1 INTRODUCTION 1.1 Scope The term axial flux permanent magnet (AFPM) machine in this book relates only to permanent magnet (PM) machines with disc type rotors. Other AFPM machine topologies, e.g.
More informationJoule losses of magnets in permanent magnet synchronous machines - case concentrated winding machine
Joule losses of magnets in permanent magnet synchronous machines - case concentrated winding machine Hanne Jussila Lappeenranta University of Technology 1 Joule losses of permanent magnets Eddy current
More informationEffect of Permanent Magnet Rotor Design on PMSM Properties
Transactions on Electrical Engineering, Vol. 1 (2012), No. 3 98 Effect of Permanent Magnet Rotor Design on PMSM Properties SEKERÁK Peter, HRABOVCOVÁ Valéria, RAFAJDUS Pavol, KALAMEN Lukáš, ONUFER Matúš
More informationElectromagnetic and Thermal Modeling of a Permanent Magnet Synchronous Machine with Either a Laminated or SMC Stator
Electromagnetic and Thermal Modeling of a Permanent Magnet Synchronous Machine with Either a Laminated or SMC Stator David K. Farnia Burgess Norton Mfg. Geneva, IL 60134 dkfarnia@burgessnorton.com Tetsuya
More informationFig Electromagnetic Actuator
This type of active suspension uses linear electromagnetic motors attached to each wheel. It provides extremely fast response, and allows regeneration of power consumed by utilizing the motors as generators.
More informationTrends in Dimensioning PM and Reluctance Machines
17 Trends in Dimensioning PM and Reluctance Machines Trends in Dimensioning PM and Reluctance Machines Tim Miller FEMAG Anwendertreffen 2015 28. 29. Oktober 2015 2015 Retrospeed 1 Dimensions Size + Shape
More informationEEE3441 Electrical Machines Department of Electrical Engineering. Lecture. Introduction to Electrical Machines
Department of Electrical Engineering Lecture Introduction to Electrical Machines 1 In this Lecture Induction motors and synchronous machines are introduced Production of rotating magnetic field Three-phase
More informationComparative Performance of FE-FSM, PM-FSM and HE-FSM with Segmental Rotor Hassan Ali Soomro a, Erwan Sulaiman b and Faisal Khan c
Comparative Performance of FE-FSM, PM-FSM and HE-FSM with Segmental Rotor Hassan Ali Soomro a, Erwan Sulaiman b and Faisal Khan c Department of Electrical power Engineering, Universiti Tun Hussein Onn
More informationDesign of Large Scale Permanent Magnet Synchronous Generators for Wind Turbines
Design of Large Scale Permanent Magnet Synchronous Generators for Wind Turbines Helena Khazdozian Wind Energy Science, Engineering and Policy Major Department: Electrical and Computer Engineering Advisor:
More information14 Single- Phase A.C. Motors I
Lectures 14-15, Page 1 14 Single- Phase A.C. Motors I There exists a very large market for single-phase, fractional horsepower motors (up to about 1 kw) particularly for domestic use. Like many large volume
More informationCHAPTER 3 BRUSHLESS DC MOTOR
53 CHAPTER 3 BRUSHLESS DC MOTOR 3.1 INTRODUCTION The application of motors has spread to all kinds of fields. In order to adopt different applications, various types of motors such as DC motors, induction
More informationSynchronous Motor Drives
UNIT V SYNCHRONOUS MOTOR DRIVES 5.1 Introduction Synchronous motor is an AC motor which rotates at synchronous speed at all loads. Construction of the stator of synchronous motor is similar to the stator
More informationThe Effects of Magnetic Circuit Geometry on Torque Generation of 8/14 Switched Reluctance Machine
213 XXIV International Conference on Information, Communication and Automation Technologies (ICAT) October 3 November 1, 213, Sarajevo, Bosnia and Herzegovina The Effects of Magnetic Circuit Geometry on
More informationCHAPTER 4 MODELING OF PERMANENT MAGNET SYNCHRONOUS GENERATOR BASED WIND ENERGY CONVERSION SYSTEM
47 CHAPTER 4 MODELING OF PERMANENT MAGNET SYNCHRONOUS GENERATOR BASED WIND ENERGY CONVERSION SYSTEM 4.1 INTRODUCTION Wind energy has been the subject of much recent research and development. The only negative
More informationPage 1. Design meeting 18/03/2008. By Mohamed KOUJILI
Page 1 Design meeting 18/03/2008 By Mohamed KOUJILI I. INTRODUCTION II. III. IV. CONSTRUCTION AND OPERATING PRINCIPLE 1. Stator 2. Rotor 3. Hall sensor 4. Theory of operation TORQUE/SPEED CHARACTERISTICS
More informationDEPARTMENT OF ELECTRICAL AND ELECTRONICS ENGINEERING
DEPARTMENT OF ELECTRICAL AND ELECTRONICS ENGINEERING QUESTION BANK 16EET41 SYNCHRONOUS AND INDUCTION MACHINES UNIT I SYNCHRONOUS GENERATOR 1. Why the stator core is laminated? 2. Define voltage regulation
More informationINFLUENCE OF MAGNET POLE ARC VARIATION ON THE COGGING TORQUE OF RADIAL FLUX PERMANENT MAGNET BRUSHLESS DC (PMBLDC) MOTOR
INFLUENCE OF MAGNET POLE ARC VARIATION ON THE COGGING TORQUE OF RADIAL FLUX PERMANENT MAGNET BRUSHLESS DC (PMBLDC) MOTOR Amit N.Patel 1, Aksh P. Naik 2 1,2 Department of Electrical Engineering, Institute
More information2014 ELECTRICAL TECHNOLOGY
SET - 1 II B. Tech I Semester Regular Examinations, March 2014 ELECTRICAL TECHNOLOGY (Com. to ECE, EIE, BME) Time: 3 hours Max. Marks: 75 Answer any FIVE Questions All Questions carry Equal Marks ~~~~~~~~~~~~~~~~~~~~~~~~~~
More informationA novel flux-controllable vernier permanent-magnet machine
Title A novel flux-controllable vernier permanent-magnet machine Author(s) Liu, C; Zhong, J; Chau, KT Citation The IEEE International Magnetic Conference (INTERMAG2011), Teipei, Taiwan, 25-29 April 2011.
More informationElectrical Engineering Department, Government Engineering College, Bhuj, India. Figure 1 Dual rotor single stator Axial Flux PM motor
American International Journal of Research in Science, Technology, Engineering & Mathematics Available online at http://www.iasir.net ISSN (Print): 2328-3491, ISSN (Online): 2328-3580, ISSN (CD-ROM): 2328-3629
More informationEuropean Conference on Nanoelectronics and Embedded Systems for Electric Mobility
European Conference on Nanoelectronics and Embedded Systems for Electric Mobility emobility emotion 25-26 th September 2013, Toulouse, France 6-phase Fault-Tolerant Permanent Magnet Traction Drive for
More informationDesign of a Cost-Efficient High-Speed High- Efficiency PM Machine for Compressor Applications
Design of a Cost-Efficient High-Speed High- Efficiency PM Machine for Compressor Applications A. Gilson, S. Tavernier, M. Gerber and C. Espanet Moving Magnet Technologies Besançon, France adrien.gilson@movingmagnet.com
More information5. LINEAR MOTORS 5.1 INTRODUCTION
5.1 INTRODUCTION 5. LINEAR MOTORS Linear Electric Motors belong to the group of Special electrical machines that convert electrical energy into mechanical energy of translator motion. Linear Electric motors
More informationLosses Calculation of an Aerospace Retraction Wheel Motor with Regarding to Electromagnetic-Field Analysis Investigation
Journal of Energy and Power Engineering 10 (2016) 183-190 doi: 10.17265/1934-8975/2016.03.006 D DAVID PUBLISHING Losses Calculation of an Aerospace Retraction Wheel Motor with Regarding to Electromagnetic-Field
More informationArtificial-Intelligence-Based Electrical Machines and Drives
Artificial-Intelligence-Based Electrical Machines and Drives Application of Fuzzy, Neural, Fuzzy-Neural, and Genetic-Algorithm-Based Techniques Peter Vas Professor of Electrical Engineering University
More informationThe use of Simulation in Electric Machine Design Stefan Holst, CD-adapco
The use of Simulation in Electric Machine Design Stefan Holst, CD-adapco Motivation How often can a machine be started within an hour In Hybrids, what effect has the adjacent combustion drive train Space
More informationOptimization Design of an Interior Permanent Magnet Motor for Electro Hydraulic Power Steering
Indian Journal of Science and Technology, Vol 9(14), DOI: 10.17485/ijst/2016/v9i14/91100, April 2016 ISSN (Print) : 0974-6846 ISSN (Online) : 0974-5645 Optimization Design of an Interior Permanent Magnet
More informationA Quantitative Comparative Analysis of a Novel Flux-Modulated Permanent Magnet Motor for Low-Speed Drive
ANSYS 11 中国用户大会优秀论文 A Quantitative Comparative Analysis of a Novel Flux-Modulated Permanent Magnet Motor for Low-Speed Drive W. N. Fu, and S. L. Ho The Hong Kong Polytechnic University, Hung Hom, Kowloon,
More informationPM Assisted, Brushless Wound Rotor Synchronous Machine
Journal of Magnetics 21(3), 399-404 (2016) ISSN (Print) 1226-1750 ISSN (Online) 2233-6656 http://dx.doi.org/10.4283/jmag.2016.21.3.399 PM Assisted, Brushless Wound Rotor Synchronous Machine Qasim Ali 1,
More informationDesign of Inverter Driven Induction Machines. Daniel M. Saban, PE PhD
Design of Inverter Driven Induction Machines Daniel M. Saban, PE PhD saban@ieee.org Overview The induction machine problem Stakeholders & design drivers Analysis & synthesis challenges Design rules-of-thumb
More informationWITH the requirements of reducing emissions and
IEEE TRANSACTIONS ON MAGNETICS, VOL. 51, NO. 3, MARCH 2015 8201805 Investigation and Design of a High-Power Flux-Switching Permanent Magnet Machine for Hybrid Electric Vehicles Wei Hua, Gan Zhang, and
More informationDesign of Sensorless Controlled IPMSM with Concentrated Winding for EV Drive at Low speed
EVS27 Barcelona, Spain, November 17-20, 2013 Design of Sensorless Controlled IPMSM with Concentrated Winding for EV Drive at Low speed Myung-Seop Lim 1, Seung-Hee Chai 1 and Jung-Pyo Hong 1, Senior Member,
More informationA Novel Axial-flux Electric Machine for In-wheel Gearless Drive in Plug-in Hybrid Electric Vehicles
A Novel Axial-flux Electric Machine for In-wheel Gearless Drive in Plug-in Hybrid Electric Vehicles W. N. Fu, and S. L. Ho The Hong Kong Polytechnic University, Hung Hom, Kowloon, Hong Kong A novel low-speed
More informationDESIGN OF AXIAL FLUX BRUSHLESS DC MOTOR BASED ON 3D FINITE ELEMENT METHOD FOR UNMANNED ELECTRIC VEHICLE APPLICATIONS
DESIGN OF AXIAL FLUX BRUSHLESS DC MOTOR BASED ON 3D FINITE ELEMENT METHOD FOR UNMANNED ELECTRIC VEHICLE APPLICATIONS 1 H. SURYOATMOJO, R. MARDIYANTO, G. B. A. JANARDANA, M. ASHARI Department of Electrical
More informationModern Motor Control Applications and Trends Tomas Krecek, Ondrej Picha, Steffen Moehrer. Public Information
Modern Motor Control Applications and Trends Tomas Krecek, Ondrej Picha, Steffen Moehrer Content Introduction Electric Machines Basic and Advance Control Techniques Power Inverters and Semiconductor Requirements
More informationAn Investigation of Advanced Magnetic Materials for Axial Field Brushless Permanent Magnet Motor Drives for Automotive Applications
The following paper posted here is not the official IEEE published version. The final published version of this paper can be found in the Proceedings of the IEEE Power Electronics Specialist Conference
More informationNote 8. Electric Actuators
Note 8 Electric Actuators Department of Mechanical Engineering, University Of Saskatchewan, 57 Campus Drive, Saskatoon, SK S7N 5A9, Canada 1 1. Introduction In a typical closed-loop, or feedback, control
More informationDesign Analysis of a Dual Rotor Permanent Magnet Machine driven Electric Vehicle
Design Analysis of a Dual Rotor Permanent Magnet Machine driven Electric Vehicle Mohd Izzat Bin Zainuddin 1, Aravind CV 1,* 1 School of Engineering, Taylor s University, Malaysia Abstract. Electric bike
More informationRemy HVH250 Application Manual Remy HVH250 Application Manual
Preliminary Draft HVH250 MotorManual20110407.doc Page 1 of 31 TABLE OF CONTENTS 1. INTRODUCTION...3 2. SYSTEM OVERVIEW...3 2.1 Installation Overview...3 2.2 Motor Overview...3 3. HVH MOTOR TYPICAL APPLICATIONS...4
More informationStep Motor Lower-Loss Technology An Update
Step Motor Lower-Loss Technology An Update Yatsuo Sato, Oriental Motor Management Summary The demand for stepping motors with high efficiency and low losses has been increasing right along with the existing
More informationCHAPTER 4 HARDWARE DEVELOPMENT OF DUAL ROTOR RADIAL FLUX PERMANENT MAGNET GENERATOR FOR STAND-ALONE WIND ENERGY SYSTEMS
66 CHAPTER 4 HARDWARE DEVELOPMENT OF DUAL ROTOR RADIAL FLUX PERMANENT MAGNET GENERATOR FOR STAND-ALONE WIND ENERGY SYSTEMS 4.1 INTRODUCTION In this chapter, the prototype hardware development of proposed
More informationCHAPTER 6 INTRODUCTION TO MOTORS AND GENERATORS
CHAPTER 6 INTRODUCTION TO MOTORS AND GENERATORS Objective Describe the necessary conditions for motor and generator operation. Calculate the force on a conductor carrying current in the presence of the
More informationNew Self-Excited Synchronous Machine with Tooth Concentrated Winding
New Self-Excited Synchronous Machine with Tooth Concentrated Winding Gurakuq Dajaku 1) and Dieter Gerling 2), IEEE 1 FEAAM GmbH, D-85577 Neubiberg, Germany 2 Universitaet der Bundeswehr Muenchen, D-85577
More informationProcedia - Social and Behavioral Sciences 195 ( 2015 ) World Conference on Technology, Innovation and Entrepreneurship
Available online at www.sciencedirect.com ScienceDirect Procedia - Social and Behavioral Sciences 195 ( 2015 ) 2586 2591 World Conference on Technology, Innovation and Entrepreneurship Application of Finite
More informationTransient analysis of a new outer-rotor permanent-magnet brushless DC drive using circuit-field-torque coupled timestepping finite-element method
Title Transient analysis of a new outer-rotor permanent-magnet brushless DC drive using circuit-field-torque coupled timestepping finite-element method Author(s) Wang, Y; Chau, KT; Chan, CC; Jiang, JZ
More informationConverteam: St. Mouty, A. Mirzaïan FEMTO-ST: A. Berthon, D. Depernet, Ch. Espanet, F. Gustin
Permanent Magnet Design Solutions for Wind Turbine applications Converteam: St. Mouty, A. Mirzaïan FEMTO-ST: A. Berthon, D. Depernet, Ch. Espanet, F. Gustin Outlines 1. Description of high power electrical
More informationChapter 2 PRINCIPLES OF AFPM MACHINES. 2.1 Magnetic circuits Single-sided machines Double-sided machines with internal PM disc rotor
Chapter 2 PRINCIPLES OF AFPM MACHINES In this chapter the basic principles of the AFPM machine are explained in details. Considerable attention is given to the magnetic circuits, windings, torque production,
More informationCooling Enhancement of Electric Motors
Cooling Enhancement of Electric Motors Authors : Yasser G. Dessouky* and Barry W. Williams** Dept. of Computing & Electrical Engineering Heriot-Watt University Riccarton, Edinburgh EH14 4AS, U.K. Fax :
More informationContents. Review of Electric Circuitd. Preface ;
Preface ; Chapter 1 Review of Electric Circuitd 1.1 Introduction, 1 1.2 Direct Circuit Current, 1 1.2.1 Voltage, 3 1.2.2 Power, 3 1.2.3 Ohm's Law, 5 1.2.4 KirchhofTs Laws, 5 1.2.4.1 Kirchhoff s Current
More informationEE6401 ELECTRICAL MACHINES I UNIT I: MAGNETIC CIRCUITS AND MAGNETIC MATERIALS PART: A 1. Define EMF and MMF. 2. Name the main magnetic quantities with their symbols having the following units: Webers,
More informationSSC-JE STAFF SELECTION COMMISSION ELECTRICAL ENGINEERING STUDY MATERIAL ELECTRICAL MACHINES
1 SSC-JE STAFF SELECTION COMMISSION ELECTRICAL ENGINEERING STUDY MATERIAL 28-B/7, Jia Sarai, Near IIT, Hauz Khas, New Delhi-110016. Ph. 011-26514888. www.engineersinstitute.com 2 CONTENT 1. : DC MACHINE,
More informationIMPACT OF SKIN EFFECT FOR THE DESIGN OF A SQUIRREL CAGE INDUCTION MOTOR ON ITS STARTING PERFORMANCES
IMPACT OF SKIN EFFECT FOR THE DESIGN OF A SQUIRREL CAGE INDUCTION MOTOR ON ITS STARTING PERFORMANCES Md. Shamimul Haque Choudhury* 1,2, Muhammad Athar Uddin 1,2, Md. Nazmul Hasan 1,2, M. Shafiul Alam 1,2
More informationMechatronics Chapter 10 Actuators 10-3
MEMS1049 Mechatronics Chapter 10 Actuators 10-3 Electric Motor DC Motor DC Motor DC Motor DC Motor DC Motor Motor terminology Motor field current interaction Motor commutator It consists of a ring of
More information4. What are the various stator current modes used in synchronous reluctance motor? Unipolar current modes, bipolar current modes.
DHANALAKSHMI COLLEGE OF ENGINEERING DEPARTMENT OF ELECTRICAL AND ELECTRONICS ENGINEERING EE6703 SPECIAL ELECTRICAL MACHINES UNIT I SYNCHRONOUS RELUCTANCE MOTORS PART A 1. What are SYNREL motors? (Dec 13,
More informationTurboDisc Stepper Motors
TurboDisc Stepper Motors P43 P532 P31 P11 P1 The TurboDisc provides exceptional dynamic performance unparalleled by any other stepper on the market. The unique thin disc magnet enables finer step resolutions
More informationAsynchronous slip-ring motor synchronized with permanent magnets
ARCHIVES OF ELECTRICAL ENGINEERING VOL. 66(1), pp. 199-206 (2017) DOI 10.1515/aee-2017-0015 Asynchronous slip-ring motor synchronized with permanent magnets TADEUSZ GLINKA, JAKUB BERNATT Institute of Electrical
More informationLower-Loss Technology
Lower-Loss Technology FOR A STEPPING MOTOR Yasuo Sato (From the Fall 28 Technical Conference of the SMMA. Reprinted with permission of the Small Motor & Motion Association.) Management Summary The demand
More informationEE6401 ELECTRICAL MACHINES I UNIT I: MAGNETIC CIRCUITS AND MAGNETIC MATERIALS PART: A 1. Define EMF and MMF. 2. Name the main magnetic quantities
EE6401 ELECTRICAL MACHINES I UNIT I: MAGNETIC CIRCUITS AND MAGNETIC MATERIALS PART: A 1. Define EMF and MMF. 2. Name the main magnetic quantities with their symbols having the following units: Webers,
More informationDesign and Analysis of Novel Bearingless Permanent Magnet Synchronous Motor for Flywheel Energy Storage System
Progress In Electromagnetics Research M, Vol. 51, 147 156, 216 Design and Analysis of Novel Bearingless Permanent Magnet Synchronous Motor for Flywheel Energy Storage System Huangqiu Zhu and Ronghua Lu*
More informationAPGENCO/APTRANSCO Assistant Engineer Electrical Previous Question Papers Q.1 The two windings of a transformer is conductively linked. inductively linked. not linked at all. electrically linked. Q.2 A
More informationSYNCHRONOUS GENERATOR (ALTERNATOR)
i SYLLABUS osmania university UNIT - I SYNCHRONOUS MACHINES Constructional Details, Types of Windings, Winding Factors, EMF Equation, Fractional Pitch and Fractional Slot Windings, Suppression of Harmonics
More information2 nd International Conference on Engineering Optimization
2 nd International Conference on Engineering Optimization September 6-9, 2010, Lisbon, Portugal Brushless Permanent Magnet Motor Losses Minimization with Constraints in Perspective of Life Cycle Assessment
More informationExperimental Evaluations of the Dual-Excitation Permanent Magnet Vernier Machine
Experimental Evaluations of the Dual-Excitation Permanent Magnet Vernier Machine Akio Toba*, Hiroshi Ohsawa*, Yoshihiro Suzuki**, Tukasa Miura**, and Thomas A. Lipo*** Fuji Electric Co. R&D, Ltd. * 1 Fuji-machi,
More informationIntroduction. Introduction. Switched Reluctance Motors. Introduction
UNIVERSITY OF TECHNOLOGY, SYDNEY FACULTY OF ENGINEERING 48550 Electrical Energy Technology Switched Reluctance Motors Topics to cover: 1. Introduction 2. Structures & Torque Production 3. Drive Circuits
More informationElectric Machines I 2017 Shiraz University of Technology Dr. A. Rahideh
In The Name of God The Most Compassionate, The Most Merciful Electric Machines I Table of Contents 1. Introduction to Electric Machines 2. Electromagnetic Circuits 3. Principle of Electromechanical Energy
More informationFigure 4.1.1: Cartoon View of a DC motor
Problem 4.1 DC Motor MASSACHUSETTS INSTITUTE OF TECHNOLOGY Department of Electrical Engineering and Computer Science 6.007 Applied Electromagnetics Spring 2011 Problem Set 4: Forces and Magnetic Fields
More informationAC Motors vs DC Motors. DC Motors. DC Motor Classification ... Prof. Dr. M. Zahurul Haq
AC Motors vs DC Motors DC Motors Prof. Dr. M. Zahurul Haq http://teacher.buet.ac.bd/zahurul/ Department of Mechanical Engineering Bangladesh University of Engineering & Technology ME 6401: Advanced Mechatronics
More informationNoise and vibration due to rotor eccentricity in a HDD spindle system
DOI 10.1007/s00542-014-2139-2 Technical Paper Noise and vibration due to rotor eccentricity in a HDD spindle system Sangjin Sung Gunhee Jang Kyungjin Kang Received: 7 October 2013 / Accepted: 8 March 2014
More informationPower Electronics & Drives [Simulink, Hardware-Open & Closed Loop]
Power Electronics & [Simulink, Hardware-Open & Closed Loop] Project code Project theme Application ISTPOW801 Estimation of Stator Resistance in Direct Torque Control Synchronous Motor ISTPOW802 Open-Loop
More informationCharacteristics Analysis of Novel Outer Rotor Fan-type PMSM for Increasing Power Density
Journal of Magnetics 23(2), 247-252 (2018) ISSN (Print) 1226-1750 ISSN (Online) 2233-6656 https://doi.org/10.4283/jmag.2018.23.2.247 Characteristics Analysis of Novel Outer Rotor Fan-type PMSM for Increasing
More informationPERMANENT-MAGNET (PM) motors have been the
IEEE TRANSACTIONS ON MAGNETICS, VOL. 42, NO. 7, JULY 2006 1861 Analytical Design of Permanent-Magnet Traction-Drive Motors Chunting Chris Mi Department of Electrical and Computer Engineering, University
More informationIron loss and eddy-current loss analysis in a low-power BLDC motor with magnet segmentation *
ARCHIVES OF ELECTRICAL ENGINEERING VOL. 61(1), pp. 33-46 (2012) DOI 10.2478/v10171-012-0003-5 Iron loss and eddy-current loss analysis in a low-power BLDC motor with magnet segmentation * ADRIAN MŁOT 1,
More informationComprehensive Technical Training
Comprehensive Technical Training For Sugar Mills Staff on Operation & Maintenance of Baggase Based HP Cogeneration System Schedule: 10 th July to 13 th July, 2017 A.C. GENERATOR Topics Covered. Introduction.
More informationElectric Machines CHARLES A. GROSS. Aubum University Auburn, Alabama, U.S.A. LßP) CRC Press Vv* / Taylor & Francis Croup. Boca Raton London New York
Electric Machines CHARLES A. GROSS Aubum University Auburn, Alabama, U.S.A. LßP) CRC Press Vv* / Taylor & Francis Croup Boca Raton London New York CRC Press is an imprint of the Taylor & Francis Group,
More information