HARD TRI-FOLD COVER SPECIAL BOLT ON SIDE RAIL INSTRUCTIONS 2016-ON TOYOTA TACOMA 5 BOX
|
|
- Christopher Dawson
- 6 years ago
- Views:
Transcription
1 HARD TRI-FOLD COVER SPECIAL BOLT ON SIDE RAIL INSTRUCTIONS 2016-ON TOYOTA TACOMA 5 BOX Read and follow these special instructions along with the standard instructions carefully before installing or using this cover. NOTICE TO INSTALLER: Even if familiar with product, read special instructions prior to installation as improvements may be made without notice. Always handle components with care. When done, these special instructions must be given to the consumer. NOTICE TO CONSUMER: Before using this product, read special instructions. Save these special instructions for future reference. NOTE TO OWNER AND INSTALLER: 1. Side rails in this kit mount to the deck rail system with special bolt on brackets instead of standard clamps as shown in standard instructions. 2. Cover may disable or limit use of some deck rail systems.
2 PREPARATION TOOLS NEEDED Protective eyewear Ratchet with 10 mm, 7/16 and 1/2 sockets Torque wrench! CAUTION: Over torquing hardware may damage components. Do not use impact tools. 1. INSTALLING WEATHER SEAL A. Clean vertical surface above deck rail system from bulkhead to tailgate with alcohol pad on both sides. Area above deck rail NOTE: For best adhesion, ensure surface is clean and air along with surface temperatures are above 60 o F. B. Peel small segment of paper backing from one end of D weather seal. At rear of truck, align top of weather seal with top of box rail then adhere weather seal segment without backing to vertical surface above deck rail system. NOTE: Ensure the top of seal is flush with box rail. C. From tailgate to bulkhead, continue peeling paper backing and adhering weather seal to vertical surface above deck rail system until bulkhead gap. Bulkhead Weather seal Bulkhead gap Area above deck rail Weather seal Truck rear Deck rail 2
3 1. INSTALLING WEATHER SEAL (Continued) D. At bulkhead gap, pull seal section through at downward angle. TIP: Leave paper backing on section to allow for seal placement. Once seal is in place, carefully peel paper backing without removing seal from gap. Angle seal downward at bulkhead gap NOTE: Angling the seal, allows water to drain. E. Trim excess weather seal from both ends. 2 INSTALLING BRACKETS TO SIDE RAIL NOTE: Before installing brackets, be aware front and middle brackets are different from rear brackets. Ensure to use the correct bracket that corresponds with its rail position. Front and middle brackets Rear bracket A. For front and middle brackets, assemble to side rail with 1/4-20 x 3/4 bolts, flat washers, lock washers and nuts. Finger tighten and ensure brackets can be adjusted in or out. NOTE: Side rail attaches to front and middle brackets through square slots. 1/4-20 x 3/4 bolt Side rail 1/4-20 x 3/4 bolt Front bracket Square slot Middle bracket 1/4 Flat washer 1/4 Lock washer 1/4-20 Hex nut 3
4 2 INSTALLING BRACKETS TO SIDE RAIL (Continued) B. For rear bracket, assemble to side rail with 1/4-20 x 3/4 bolt, flat washer, lock washer and nut. Finger tighten and ensure bracket can be adjusted in or out. NOTE: Side rail attaches to rear bracket through square slot. Square slot Rear bracket 1/4 Flat washer 1/4 Lock washer 1/4-20 Hex nut 1/4-20 x 3/4 bolt 3. INSTALLING SIDE RAILS A. Remove plug at end of channel by tailgate. Remove plug B. Use 10 mm socket with ratchet to remove 6 mm bolt near end of truck. Save 6 mm bolt for reuse in Step 3G on page 6. 6 mm bolt 4
5 3. INSTALLING SIDE RAILS (Continued) C. Slide carriage bolt bracket and 5/16 x 1-1/4 carriage bolt into channel of deck rail system, one set per front and middle bracket. D. Reinsert deck rail system plug at end of channel near tailgate. Weather seal Deck rail system E. For front and middle brackets, position side rail against inside lip of box. Align carriage bolts with brackets on side rails. Push side rail forward until rail touches front of box. NOTE: Ensure contoured portion of side rail is at rear of truck. 5/16 x 1-1/4 Carriage bolt and bracket Align slot in bracket with carriage bolt F. Secure with 5/16 serrated nuts. Leave finger tight for now. 5/16 serrated nut 5
6 3. INSTALLING SIDE RAILS (Continued) G. For rear bracket, attach bracket to box with 6 mm bolt (removed in Step 3B). Leave finger tight for now. 6 mm bolt H. For front and middle brackets, align side rail edge with bracket edge then tighten 1/4-20 nut. Align edge of side rail with edge of bracket Tighten 1/4-20 nut I. At front and middle bracket, set height according to standard instructions. J. Position side rail and bracket against box rail and tighten 5/16 serrated nut. Hold side rail level while tightening Tighten 5/16 serrated nut 6
7 3. INSTALLING SIDE RAILS (Continued) NOTE: Before proceeding, ensure weather seal contacts side rail and creates a seal. Weather seal under side rail K. For rear bracket, align side rail edge with bracket edge then tighten 1/4-20 nut. Align edge of side rail with edge of bracket Tighten 1/4-20 nut L. Position side rail and bracket against box rail and tighten 6 mm bolt. Hold side rail level while tightening Tighten 6 mm bolt M. Repeat to install side rail on opposite side. N. Torque 5/16 nuts on 5/16 x 1-1/4 carriage bolts to 20 ft-lbs. O. Torque 1/4-20 nuts on 1/4-20 x 3/4 carriage bolts to 10 ft-lbs. P. Torque 6 mm bolts to 8 ft-lbs. Q. For remaining cover installation, refer to standard instructions. 7
8 Product subject to change without notice _A
HARD TRI-FOLD COVER SPECIAL BOLT ON SIDE RAIL INSTRUCTIONS 2016-ON TOYOTA TACOMA 6 BOX
HARD TRI-FOLD COVER SPECIAL BOLT ON SIDE RAIL INSTRUCTIONS 2016-ON TOYOTA TACOMA 6 BOX Read and follow these special instructions along with the standard instructions carefully before installing or using
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Thank you for purchasing VANISH Roll-Up Cover. Agri-Cover, Inc. proudly manufactured this cover using superior quality materials and workmanship. With proper care, your cover
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Thank you for purchasing ACCESS Original Roll-Up Cover. Agri-Cover, Inc. proudly manufactured this cover using superior quality materials and workmanship. With proper care, your
More informationINSTALLATION INSTRUCTIONS AND OWNER S MANUAL
INSTALLATION INSTRUCTIONS AND OWNER S MANUAL Thank you for purchasing the AlloyCover from WeatherTech. Manufactured with pride using superior quality materials and workmanship. With proper care, your cover
More informationLIMIT SWITCH SPECIAL INSTRUCTIONS
LIMIT SWITCH SPECIAL INSTRUCTIONS Use these instructions to install a limit switch. Read and follow these instructions along with the standard instructions carefully before installing or using tarp system.
More informationINSTALLATION INSTRUCTIONS AND OWNER S MANUAL
INSTALLATION INSTRUCTIONS AND OWNER S MANUAL Thank you for purchasing the AlloyCover from WeatherTech. Manufactured with pride using superior quality materials and workmanship. With proper care, your cover
More informationJK8 Body Kit KIT CONTENTS 1 K
JK8 Body Kit KIT CONTENTS A B C 1 K6861352 D E G F H 2 K6861352 I M N J K L O P Q R S 3 K6861352 T U V W X Y CALL OUT PART NUMBER DESCRIPTION QUANTITY A P5156021 HARDTOP 1 B P5155997 BULKHEAD 1 C 1PH98/9TZZAE
More informationCENTER BELT SYSTEM INSTALLATION INSTRUCTIONS CARCG121220
CENTER BELT SYSTEM INSTALLATION INSTRUCTIONS 2013+ DODGE CHARGER Distributed by CARCG121220 Important Notice: Read all instructions before starting the installation of the seat. Before drilling or installing
More informationTONNEAU COVER SPECIAL SHIM AND CLAMP INSTRUCTIONS
TONNEAU COVER SPECIAL SHIM AND CLAMP INSTRUCTIONS ATTENTION INSTALLER: Read and follow these special instructions along with the standard instructions in owners manual. For 2014-ON Chevy/GMC 1500 Half
More informationWOC Mid Size Door Installation
WOC-10112 Mid Size Door Installation NOTE: If the Mid Size Ranger that you are installing this door system on is a 2010 or newer you will need to remove the sill plates and side nets. If the doors are
More informationTONNEAU INSTALLATION GUIDE
TONNEAU INSTALLATION GUIDE Warranty, Care & Maintenance Model 4056 Toyota Tacoma Double Cab 5' Short Bed 2005-Current (With Multi-Track System) EASY AS 1-2-3! NORMAL INSTALLATION TIME 30 MINUTES For Warranty
More information100mm. Part# AA Rev CUSTOMER SUPPORT: Wash truck bed.
Wash truck bed. 1 2 TRI-FOLD TONNEAU INSTALLATION GUIDE Sold exclusively at AutoAnything.com Please contact 800-874-8888 with any questions, to claim your warranty, or to discuss a return. You can also
More informationTOYOTA TUNDRA BUMPER STEP ASSIST Preparation
Preparation Part Number: PT392-34140 Kit Contents 1 1 Linkage Assembly 2 1 Mounting Bracket 3 1 Step Pad 4 1 Hardware Bag 5 1 Bumper Support Bracket 6 1 Bumper Re-enforcement Bracket Hardware Bag Contents
More informationTONNEAU COVER SPECIAL SHIM AND CLAMP INSTRUCTIONS
TONNEAU COVER SPECIAL SHIM AND CLAMP INSTRUCTIONS ATTENTION INSTALLER: Read and follow these special instructions along with the standard instructions in owners manual. For 2014-ON Chevy/GMC 1500 Half
More informationINSTALLATION & OWNER S MANUAL
Rev. B, p. 1 of 25 INSTALLATION & OWNER S MANUAL POLARIS RANGER RCS (for models XP or HD) (for model years 2009-) cab without doors kit (p/n 1POLRCWD) cab with doors kit (p/n 1POLRC) doors only kit (p/n
More informationTOYOTA RAV RUNNING BOARD
TOYOTA RAV4 2013 - RUNNING BOARD Part Number: 00016-42020 Accessory Code:TR1 Conflicts Mudguard Kit Contents Item # Quantity Reqd. Description 1 1 LH Board Assembly 2 1 RH Board Assembly 3 1 LH Rear Mounting
More informationINSTALLATION INSTRUCTIONS South Highway 11 Westminster, SC Toll Free (888) (864) FAX (864)
These instructions apply to the servicing of the Lift Technologies MaxiMizer Integral Sideshifters Cylinder Head. WARNING! Unless the steps in the following Installation Instructions are properly followed
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Thank you for purchasing a LOMAX TM Hard Tri-Fold or Professional Series Cover. Agri-Cover, Inc. proudly manufactured this cover using superior quality materials and workmanship.
More information2015 Mustang Lightbar (All Models) CDC#
2015 Mustang Lightbar (All Models) CDC# 1511-7000-01 Components: 1 CDC Lightbar Note: READ instructions before starting installation!!! CDC Part# Driver side bracket 0511-6001-05 Passenger side bracket
More informationINSTALLATION MANUAL MODEL 1200 FULL SIZE TRUCK MODEL 1205 COMPACT SIZE TRUCK
INSTALLATION MANUAL MODEL 1200 FULL SIZE TRUCK MODEL 1205 COMPACT SIZE TRUCK Load capacity: Up to 800 lbs. evenly distributed. Approximate Assembly and Installation Time: 60 min. (1 hr.) depending on truck
More informationMOUNTING KIT MKPBX
MOUNTING KIT 53221-MKPBX Toyota Tacoma (4x4) (2005-2015) Mounting Kit 53221-MKPBX Item Part # Description MKPBX X-MKB 1 52638-D-GA Lift Frame Galvanized 1 2 50069-C-GA Lift Channel Galvanized 1 3 HH-00972-153
More informationKK-K9-F16-K INSTALLATION INSTRUCTIONS K9 Kit for FORD EXPLORER (Retail Model Vehicle with OEM Center Shifter Console)
KK-K9-F16-K INSTALLATION INSTRUCTIONS K9 Kit for 2011-2016 FORD EXPLORER (Retail Model Vehicle with OEM Center Shifter Console) TOOLS Needed: Phillips Screw Driver Power Drill with Drill Bits Trim panel
More information2019-ON RAM 1500 INSTALLATION INSTRUCTIONS
2019-ON RAM 1500 INSTALLATION INSTRUCTIONS Thank you for purchasing ROCKSTARTM Splash Guard Mud Flaps. Agri-Cover, Inc. proudly manufactured these mud flaps using superior quality materials and workmanship.
More informationMULTI-POLE MOUNT LARGE GROUND MOUNT. Assembly Instructions. Assembly Instructions. step-by-step assembly and installation
MULTI-POLE MOUNT Assembly Instructions LARGE GROUND MOUNT Assembly Instructions step-by-step assembly and installation PCN 081711-2 The Large Ground Mount A few words about the product The Large Ground
More informationHiBoy Maverick/Commander Doors Part # HiBoy4 Maverick/Commander Doors Black
Racing 3191 N Washington St. Suite 2 Chandler, AZ 85225 1 (800) 708-9803 http://www.racing.com HiBoy Maverick/Commander Doors Part # 07-2001 HiBoy4 Maverick/Commander Doors Black Congratulations on your
More informationINSTALLATION & OWNER S MANUAL
Rev. L p. 1 of 16 INSTALLATION & OWNER S MANUAL V4262 CAMO (SOFT SIDED) CAB KIT INSTALLATION & OWNER S MANUAL The contents of this envelope are the property of the owner. Be sure to leave with the owner
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Document# 19-0038 2004+ Lotus Elise (Series 2) Rear Clamshell Removal Kit Safely support the vehicle. This is a two-person job. Allow 1 to 2 hours for initial disassembly. Have
More information2014-Current. Adjustable wrench (that opens to about 1 ), 1/2 open end wrench, Phillips screwdriver, 3/8 socket, 7/16 socket, 7/32 Allen wrench
Installation Instructions Van: VNFD13TRAN65 FORD TRANSIT 148 WHEELBASE 2014-Current TOOLS REQUIRED Adjustable wrench (that opens to about 1 ), 1/2 open end wrench, Phillips screwdriver, 3/8 socket, 7/16
More informationINSTALLATION INSTRUCTIONS
Hardware: 12M x 40M hex head bolts Qty: 4 12M flat washers Qty: 8 12M lock washers Qty: 4 12M Ny-lock hex nuts Qty: 4 Extension bracket with bolt Qty: 2 8M Ny-lock hex nuts Qty: 2 8M Lock washer Qty: 2
More informationRAM 1500, 2019 CLASSIC & 2010-ON 2500/3500 INSTALLATION INSTRUCTIONS
2009-18 RAM 1500, 2019 CLASSIC & 2010-ON 2500/3500 INSTALLATION INSTRUCTIONS Thank you for purchasing ROCKSTARTM Splash Guard Mud Flaps. Agri-Cover, Inc. proudly manufactured these mud flaps using superior
More informationINSTALLATION & OWNER S MANUAL
Rev. R p. 1 of 16 INSTALLATION & OWNER S MANUAL V4211 HARD SIDED CAB KIT and/or V4275 CAMO HARD SIDED CAB KIT INSTALLATION & OWNER S MANUAL The contents of this envelope are the property of the owner.
More informationEXPRESS/SAVANNA 155 WHEELBASE. Installation Instructions Van: VNGM96EXSV65 TOOLS REQUIRED 1996-CURRENT. follow us : CHEVROLET & GMC
Installation Instructions Van: VNGM96EXSV65 CHEVROLET & GMC EXPRESS/SAVANNA 155 WHEELBASE 1996-CURRENT TOOLS REQUIRED Adjustable wrench (that opens to about 1 ), 1/2 open end wrench, Phillips screwdriver,
More informationMODEL 2604 WARNING <THESE INSTRUCTIONS MUST BE GIVEN TO THE END USER> Custom 5th Wheel Hitch Mounting Rail Installation Instructions
B&W Trailer Hitches 1216 Hawaii Rd / PO Box 186 Humboldt, KS 66748 P:620.473.3664 F:620.869.9031 Custom 5th Wheel Hitch Mounting Rail Installation Instructions
More information2016 Toyota Tacoma INSTALLATION SHEET
2016 Toyota Tacoma INSTALLATION SHEET MISSING PARTS? call Extang at 1-800-877-2588 Any and all needed parts will be shipped to you directly. (DO NOT return whole kit to store) Drill Torx Driver-T30 Wrench
More informationTOYOTA TUNDRA BUMPER STEP ASSIST Preparation
Preparation Part Number: PT392-34140 Kit Contents Item # Quantity Reqd. Description 1 1 Linkage Assembly 2 1 Mounting Bracket 3 1 Step Pad 4 1 Hardware Bag 5 1 Bumper Support Bracket 6 1 Bumper Re-enforcement
More informationPart Number: TBL-016S
5/18/17 TOYOTA TACOMA 2016-2017 LED Bed Light Kit Part Number: TBL-016S Kit Contents Item # Quantity Reqd. Description 1 2 LED Bed Light Harness (10 ) 2 2 LED Bed Light Harness (5 ) 3 1 Y Harness Extension
More informationINSTALLATION INSTRUCTIONS JK DECK ENCLOSURE #326 (2 & 4 Door)
SHIPMENT CONTENTS INSTALLATION INSTRUCTIONS JK 2011+ DECK ENCLOSURE #326 (2 & 4 Door) Please read and fill out the enclosed warranty registration card to activate your warranty. #3 Lid #7 Front Panel #4
More informationInstallation Instructions Vanishing Lid Bracket
-800-447-88 www.coverpools.com Installation Instructions Vanishing Lid WARNING FOR YOUR SAFETY This product must be installed and serviced by a contractor who is licensed and qualified in pool equipment
More informationBolt-On/Rugged Fender Flares Nissan Titan (04-15) Please read instructions entirely before installing this product.
Please read instructions entirely before installing this product. Hardware Included QTY FUEL DOOR CLIP 1 Bolt Kit Included QTY ALCOHOL TOWELETTE 4 M4 SCREW 1 ALLEN KEY BOLT 42 CLIP.9MM 2 ABRASIVE RESISTANT
More informationINSTALLATION INSTRUCTIONS FOR DSP9600/9100 WHEEL BALANCER
Form 5063T, 06-05 Supersedes Form 5063T, 02-04 INSTALLATION INSTRUCTIONS FOR DSP9600/9100 WHEEL BALANCER This document provides the information needed to install the DSP9600/9100 Wheel Balancer. NOTE:
More informationINSTALLATION INSTRUCTIONS AND PARTS LIST MODEL BRACKET PACKAGE TO MOUNT O-MEGA STEPS/GRIP STEPS VEHICLE APPLICATION: 2001 AND NEWER FORD VANS
INSTALLATION INSTRUCTIONS AND PARTS LIST MODEL 570124 BRACKET PACKAGE TO MOUNT O-MEGA STEPS/GRIP STEPS VEHICLE APPLICATION: 2001 AND NEWER FORD VANS READ INSTRUCTIONS COMPLETELY AND CHECK TO MAKE SURE
More informationInstallation Instructions Supertop for Truck
Installation Instructions Supertop for Truck US Patent 6827391 Vehicle Application: Toyota Tacoma Double Cab 2005-2011 (5 ft.) Part Number: 76308 INSTALLATION TIME SKILL LEVEL 1-1/2 Hours 2 - Moderately
More information2011 Cadillac CTS Coupe EGX Exhaust Tip & Rear Valance Mesh Accent Kit Part #: Complete E
BILLET GRILLS IMPORTANT: PLEASE KEEP THIS INSTRUCTION MANUAL FOR FUTURE REFERENCE! 2011 Cadillac CTS Coupe EGX Exhaust Tip & Rear Valance Mesh Accent Kit Part #: Complete 5122-1900-11E TOOLS REQUIRED Automotive
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Accessory SIDE UNDER S Application 2013 CIVIC 2-DOOR Publications No. AII 13069 Issue Date NOV 2012 PARTS LIST 4 Flare nuts Left spoiler 2 Washer-nuts Right spoiler 2 Screws 2
More informationSPECIAL INSTALLATION INSTRUCTIONS
SPECIAL INSTALLATION INSTRUCTIONS WARN 4X FLARES FRONT AND REAR '98 TOYOTA HILUX DUAL-CAB As you read these instructions, you will see NOTES, CAUTIONS and WARNINGS. Each message has a specific purpose.
More informationPARTS LIST: Components. ` Bi-Fold Tonneau Cover
` Bi-Fold Tonneau Cover Fits: 2004-2014 TFX3401 - Ford F150 5.5 2004-2014 TFX3402 - Ford F150 6.5 2015 TFX3403 - Ford F150 5.5 2015 TFX3404 - Ford F150 6.5 1999-2007 TFX3405 - Ford F250/F350 6.5 2008-2015
More informationInstallation Instructions Bolt-On Fender Flares Ford F150 (09-12) Part #17394
Please read instructions entirely before installing this product. Hardware Included QTY Hardware Included QTY Bolt Kit Included QTY EXTRUSION 29.5ft ALCOHOL TOWELETTE 4 BLACK HEX BOLT 42 RETAINING CLIP.9mm
More informationINSTALLATION MANUAL
INSTALLATION MANUAL 2051108 Parts List 1 Driver / left running board 1 Passenger / right running board Level of Difficulty Easy Scan for helpful install tips 2 Mounting bracket, front 2 Mounting bracket,
More informationINSTALLATION & OWNER S MANUAL
Rev. C p. 1 of 21 INSTALLATION & OWNER S MANUAL F5205 HARD SIDED CAB KIT INSTALLATION & OWNER S MANUAL The contents of this envelope are the property of the owner. Be sure to leave with the owner when
More informationDODGE RAM Current
Installation Instructions Van: VNRA13PROM65 DODGE RAM PROMASTER 159 WHEELBASE 2014-Current TOOLS REQUIRED Adjustable wrench (that opens to about 1 ), 1/2 open end wrench, Phillips screwdriver, 3/8 socket,
More informationN. 15th Street, Middlesboro, KY TARP-N-GO SYSTEMS INSTALLATION INSTRUCTIONS
1-800-248-7717 1002 N. 15th Street, Middlesboro, KY 40965 TARP-N-GO SYSTEMS INSTALLATION INSTRUCTIONS Congratulations on your purchase of a Mountain Tarp Tarp-N-Go tarping system. With tarping systems
More informationLOCKN LOAD MOUNTING KIT
LOCKN LOAD MOUNTING KIT TM VOLKSWAGEN AMAROK 2 BAR FIXED POINT HEAVY DUTY ROOF RACK SYSTEM MAX VEHICLE ROOF LOAD RATING: 100KG TOTAL LOAD EQUALS WEIGHT OF ROOF RACKS + ACCESSORIES + CARGO FIRST TIME INSTALLATION
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS OUTLAW FRONT BUMPER APPLICATION: 2014-2018 TOYOTA TUNDRA PART NUMBER: 58-61035 CONTENT ITEM QUANTITY DESCRIPTION TOOLS NEEDED 1 1 FRONT BUMPER ASSEMBLY 18MM WRENCH 2,3 2 MESHED
More informationINSTALL/REMOVAL INSTRUCTIONS: WINDOW LIFT MOTOR
REMOVAL/INSTALL OF WINDOW REGULATOR (742-269) Ford Mustang 1996 2004 General Tech Tips: Use painter s tape rather than duct tape to secure window. It will not damage paint or leave sticky residue. A plastic
More information** DO NOT EXCEED THE RECOMMENDED VEHICLE TOWING WEIGHT RATING ** DODGE RAM 1500
10/3/2017 DODGE RAM 1500 WARNING!! BRAKE, FUEL, AND ELECTRICAL LINES MAY NEED TO BE LOOSENED OR REPOSITIONED TO PROVIDE CLEARANCE FOR NEW HARDWARE. ON SHORT BED MODELS, CHECK FOR ADEQUATE TURNING CLEARANCE
More informationALUMINUM FORD F BED LENGTH. Installation Instructions: DF4 TOOLS REQUIRED 2015-CURRENT FOLLOW #DECKEDUSA
Installation Instructions: DF4 ALUMINUM FORD F150 5 6 BED LENGTH 2015-CURRENT TOOLS REQUIRED Adjustable wrench (that opens to about 1 ), 1/2 open end wrench, Phillips screwdriver, 3/8 socket, 7/16 deep
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Thank you for purchasing TONNOSPORT Roll-Up Cover. Agri-Cover, Inc. proudly manufactured this cover using superior quality materials and workmanship. With proper care, your cover
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Accessory Application Publication No. After 13 TRX420 All MII 15067 KIT (except 14 TRX420FA/FPA) Issue Date P/N 08T71-HR3-A20 After 13 TRX500 All (except 14 TRX500FA/FPA) September
More information<THESE INSTRUCTIONS MUST BE GIVEN TO THE END USER> Custom 5th Wheel Hitch Mounting Rail Installation Instructions
B&W Trailer Hitches 1216 Hawaii Rd / PO Box 186 Humboldt, KS 66748 P:620.473664 F:620.869.9031 Custom 5th Wheel Hitch Mounting Rail Installation Instructions
More informationWARNING TAKE NOTE OF THE FOLLOWING: THIS PRODUCT MUST BE INSTALLED EXACTLY AS PER THESE INSTRUCTIONS USING ONLY THE HARDWARE SUPPLIED.
ARB WINCH/NONWINCH BUMPER TO SUIT TOYOTA HJ100 IFS PRODUCT No. 3913140 5100050 Top Tube Kit 5100160 Buffer Kit With hole (required when fitting Top Tube) 5100170 Buffer Kit With no hole Fitting Kit No.
More informationPOLY TIP-DOWN WINDSHIELD KIT
POLY TIP-DOWN WINDSHIELD KIT P/N 2883261 APPLICATION Verify accessory fitment at Polaris.com. BEFORE YOU BEGIN Read these instructions and check to be sure all parts and tools are accounted for. Please
More informationOPERATOR S MANUAL. 20-bu 3-Point Hitch Material Collection System. LP65048 Supplier ST /07/2017 English. North American Edition Printed in USA
OPERATOR S MANUAL 20-bu 3-Point Hitch Material Collection System LP65048 Supplier ST48289 11/07/2017 English North American Edition Printed in USA Introduction Using Your Operator s Manual Read this entire
More informationASSEMBLY INSTRUCTIONS FOR V10SE & V11SE E MOUNT RACKS P/N V10SEV-1 / V11SEV-1
ASSEMBLY INSTRUCTIONS FOR V10SE & V11SE E MOUNT RACKS P/N V10SEV-1 / V11SEV-1 V10SEV-1 shown above Package Contents: HARDWARE KIT (6) CLIPS (6) CLIP END CAPS (8) 3/8-16 x 3 CARRAIGE BOLTS (16) 3/8-16 x
More informationInstallation Guide CLAAS Lexion Combines with 9 inch Elevators
Installation Guide CLAAS Lexion Combines with 9 inch Elevators 955614_01 4/17 1 Table of Contents System Overview 3 Quick Start Guide 4 Flow Sensor Installation 5 Hydraulic Elevator Adjustment Kit Installation
More informationINVIS-A-RACK INSTALLATION INSTRUCTION DZ , DZ , DZ IR-HOUSING-ASSEML X2 IR-HOUSING-ASSEMR X2 8 FT.
A INVIS-A-RACK INSTALLATION INSTRUCTION DZ 951550, DZ 951600, DZ 951800 DRIVER FRONT / PASSENGER REAR B PASSENGER FRONT / DRIVER REAR IR-HOUSING-ASSEML X2 IR-HOUSING-ASSEMR X2 BUNGEE BOX MOUNTING HOOK
More informationUNIVERSAL CUSTOMIZABLE MUD FLAP INSTALLATION INSTRUCTIONS
UNIVERSAL CUSTOMIZABLE MUD FLAP INSTALLATION INSTRUCTIONS Thank you for purchasing ROCKSTARTM Splash Guard Mud Flaps. Agri-Cover, Inc. proudly manufactured these mud flaps using superior quality materials
More informationHaul-Your-Might T3. Product Name: Product Code: Please read all instructions carefully before assembly, installation and/or use of this product.
WARNING: DO NOT exceed 800 lbs. (363 Kgs) WARNING: DO NOT exceed vehicle manufacturer s weight rating. Tools Required: 17mm Socket 5mm Hex Key 1/8 Hex Key Tape Measure 17mm Wrench 13mm Socket Hack Saw
More informationFlip Extension Install Instructions
Tools Required: Tape Measure, knife, Allen key set, Phillips screwdriver, a 1/2" wrench, and a 1/2" socket 1.0 Preparing TRUCKBOSS Deck. 1.1 Remove the plastic end caps from the rear of the TRUCKBOSS deck.
More informationHaul-Your-Might T3. Product Name: Product Code: Please read all instructions carefully before assembly, installation and/or use of this product.
WARNING: DO NOT exceed 800 lbs. (363 Kgs) WARNING: DO NOT exceed vehicle manufacturer s weight rating. Haul-Your-Might T3 Tools Required: 17mm Socket 5mm Hex Key 1/8 Hex Key Tape Measure 17mm Wrench 13mm
More information**DO NOT EXCEED RECOMMENDED VEHICLE TOWING WEIGHT!** FORD F-250, F-350
6065 SUBKIT 7/7/0 **DO NOT EXCEED RECOMMENDED VEHICLE TOWING WEIGHT!** FORD F-50, F-50 PAGE OF WARNING!! BRAKE, FUEL, AND ELECTRICAL LINES MAY NEED TO BE LOOSENED OR REPOSITIONED TO PROVIDE CLEARANCE FOR
More informationInstalL Instructions. rock defense jeep yj roll cage kit. kit contents ins
InstalL Instructions rock defense jeep yj roll cage 300152-2-kit kit contents tube identification 300102-2 Passenger Roof Tube (Qty: 1) 300103-2 Driver Roof Tube (Qty: 1) 300104-2 Windshield Tube (Qty:
More information2017 Current Ford Raptor HoneyBadger Rear Bumper Installation Instructions
2017 Current Ford Raptor HoneyBadger Rear Bumper Installation Instructions PREPARATION 1. Disconnect the negative terminal on the battery. Park the vehicle on level ground and set the emergency brake.
More informationUniversal Installation Instructions
ROCKSTAR TM HITCH MOUNTED MUD FLAPS Universal Installation Instructions IMPORTANT! READ AND UNDERSTAND THESE INSTRUCTIONS FOR SAFETY, INSTALLATION, OPERATION, AND MAINTENANCE. SAVE ALL INSTRUCTIONS FOR
More informationPOLY TIP-DOWN WINDSHIELD KIT
POLY TIP-DOWN WINDSHIELD KIT P/N 2881919 APPLICATION Verify accessory fitment at Polaris.com. BEFORE YOU BEGIN Read these instructions and check to be sure all parts and tools are accounted for. Please
More informationASSEMBLY INSTRUCTIONS FOR TRANSIT CONNECT RACK
ASSEMBLY INSTRUCTIONS FOR TRANSIT CONNECT RACK FTC948-1 shown above Package Contents: HARDWARE KIT PARTS (4) 3/8-16 x 3 CARRIAGE BOLTS (1) RAIL DRIVER S SIDE ASSEMBLY (16) 3/8-16 x 2 CARRIAGE BOLTS (1)
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Accessory FABRIC FRONT DOORS P/N 0SR90-HL4-211A (BLACK) P/N 0SR90-HL4-221A (CAMO) Application SXS1000M3/M3P/M5P/M5D Honda Dealer: Please give a copy of these instructions to your
More informationINSTALLATION & OWNER S MANUAL
Rev. E p. of 3 INSTALLATION & OWNER S MANUAL V446 Front Cab Kit and V446 Rear Cab Kit for RTV 40 INSTALLATION & OWNER S MANUAL The contents of this envelope are the property of the owner. Be sure to leave
More informationkit contents tacoma front 3" spacer lift kit InstalLation Instructions kit ( tacoma prerunner/4wd, Runner 4wd)
tacoma front 3" spacer lift kit 300599-1-kit (1995-2013 tacoma prerunner/4wd, 1996-2012 4Runner 4wd) kit contents 5356 PINE AVE FRESNO, CA 93727 USA TOLL FREE: 877.4X4.TOYS WORLDWIDE: 559.252.4950 WWW.TRAIL-GEAR.COM
More informationINSTALLATION INSTRUCTIONS South Highway 11 Westminster, SC Toll Free (888) (864) FAX (864)
1.0 Purpose: To identify requirements for the replacement of ISS seals, o-ring and installation of gland nut to rod. 2.0 Scope: This instruction applies to the ISS units manufactured at Lift Technologies
More informationInstallation Instructions Road Defender Push Bumper Part # L Ford Sedan Police Interceptor
Installation Instructions Road Defender Push Bumper Part # 5039-2L51 2013-2015 Ford Sedan Police Interceptor Do not attempt to install this product on any vehicle other than the one listed above! Parts
More informationSUPPORTS, CANOPY W/CABLE ASSEMBLY INSTRUCTIONS KIT P/N
SUPPORTS, CANOPY W/CABLE ASSEMBLY INSTRUCTIONS KIT P/N 512-00010-00 CANOPY SUPPORTS INSTALLATION AND ADJUSTMENT Tools required: 1-7/8 open end wrench 1-3/4 open or box end wrench (or a rachet and 3/4 socket)
More information40 Plug Aerator Model# AE-40T
40 Plug Aerator Model# AE-40T 11122010 Pre-assembly Instructions: For best results, follow all directions step by step. Read entire step instructions first, and then proceed with the set up. Open all boxes
More informationMULTI-POLE MOUNT MULTI-POLE MOUNT. Assembly Instructions. Assembly Instructions. step-by-step assembly and installation
MULTI-POLE MOUNT Assembly Instructions MULTI-POLE MOUNT Assembly Instructions step-by-step assembly and installation PCN 062411-2 The Multi-Pole Mount A few words about the product The Multi-Pole Mount
More information**DO NOT EXCEED RECOMMENDED VEHICLE TOWING WEIGHT!** FORD F-250, F-350
60647 SUBKIT 7/3/204 **DO NOT EXCEED RECOMMENDED VEHICLE TOWING WEIGHT!** FORD F-250, F-350 PAGE OF 4 WARNING!! BRAKE, FUEL, AND ELECTRICAL LINES MAY NEED TO BE LOOSENED OR REPOSITIONED TO PROVIDE CLEARANCE
More informationParts List ILLUSTRATION #1
Installation Instructions BR20 Rear Bumper Replacement Part Number 28295T 2015-2016 Ford F-150 2/4WD Do not attempt to install this product on any vehicle other than the one listed above! Parts List Item
More informationHARD FOLDING TONNEAU COVER INSTALLATION GUIDE
HARD FOLDING TONNEAU COVER INSTALLATION GUIDE GUIDE FOR FOLD-A-COVER FD3701, FD3702 TRUCK MODEL(S): 1998-2007 FORD F-150 NOTES TO INSTALLER: 70 F when installing. surface. Some trimming of bed liner may
More informationInstallation Instructions KNOCK DOWN INSTATRUNK
Installation Instructions KNOCK DOWN INSTATRUNK Vehicle Application: Jeep Wrangler and Wrangler Unlimited 2007 2010 : 42702 INSTALLATION TIME SKILL LEVEL 1/2 Hour 1 - Easy TOOLS 10 mm and 15 mm 9/16" and
More informationINSTALLATION INSTRUCTIONS Toyota FJ Cruiser DEMELLO-OFFROAD.
INSTALLATION INSTRUCTIONS Item Description Vehicle 3 piece Rear Bumper 2007-2014 Toyota FJ Cruiser DEMELLO-OFFROAD www.demello-offroad.com 12785 magnolia ave Riverside ca 92503 Suite 1 phone: 1-951-735-4417
More informationInstallation Instructions
Installation Instructions TrailView Soft Top Important Safety Information For proper installation and best possible fit, please read all instructions BEFORE you begin. Periodically check all components
More informationTOYOTA TUNDRA SKID PLATE Preparation
Preparation Part Number: PT98-4140 Kit Contents Item # Quantity Reqd. Description 1 1 Skid Plate (Pre-Assembled with Hardware) 2 1 Hardware Bag Hardware Bag Contents Item # Quantity Reqd. Description 1
More informationFlexJet - Flex Cable Replacement
P/N: 109515R0 14140 NE 200th St. Woodinville, WA. 98072 PH: (425) 398-8282 FX: (425) 398-8383 FlexJet - Flex Cable Replacement Notices: Warning! Ensure that all AC power cables are removed from the printer
More information2007-Current. Adjustable wrench (that opens to about 1 ), 1/2 open end wrench, Phillips screwdriver, 3/8 socket, 7/16 socket, 7/32 Allen wrench
Installation Instructions Van: VNMB07SPRT55 MERCEDES BENZ / DODGE / FREIGHTLINER SPRINTER VAN 144.3 WHEELBASE 2007-Current TOOLS REQUIRED Adjustable wrench (that opens to about 1 ), 1/2 open end wrench,
More informationINSTALLATION INSTRUCTIONS
Accessory Application Publication No. INSTALLATION INSTRUCTIONS SADDLEBAG P/N 08L70-MGZ-A80 COMMON Honda Dealer: Please give a copy of these instructions to your customer. MII 15802 Issue Date March 2016
More informationLexus ES Fine Mesh and Adaptive Cruise Control Fine Mesh Grilles Upper and Lower Replacements
IMPORTANT: PLEASE KEEP THIS INSTRUCTION MANUAL FOR FUTURE REFERENCE! 2013-15 Lexus ES Fine Mesh and Adaptive Cruise Control Fine Mesh Grilles Upper and Lower Replacements Part #1372-0102-13 / Black Ice
More informationTOOLS REQUIRED. INSTALLATION INSTRUCTIONS TRUCK MODEL: DT1 TOYOTA TUNDRA 5 7 bed length 2007-current year. NOTE: These might actually be useful
INSTALLATION INSTRUCTIONS TRUCK MODEL: DT1 TOYOTA TUNDRA 5 7 bed length 2007-current year VERSION 1.5 TOOLS REQUIRED Adjustable wrench (that opens to about 1 ), 1/2 open end wrench, Phillips screwdriver,
More informationMobtown Offroad Toyota Tacoma Bolt On Rock Slider Installation Instructions
Mobtown Offroad 2005+ Toyota Tacoma Bolt On Rock Slider Installation Instructions Tools Needed: 9/16 Box Wrench 9/16 Standard and Deep Well Socket, 3/8 Drive Ratchet, 3/8 Drive 3/4 Standard Socket 3/4
More information2005 Cadillac CTS BRAKES Disc Brakes - CTS
Removal Procedure 1. Inspect the fluid level in the brake master cylinder reservoir. 2. If the brake fluid level is midway between the maximum-full point and the minimum allowable level, no brake fluid
More informationLEXUS IS 250/350/250 AWD REAR GS SHOCK ABSORBERS Preparation. Part Number: PTR PTR PTR
Preparation Part Number: PTR13-53082 PTR13-53092 PTR13-53095 Kit Contents Item # Quantity Reqd. Description 1 1 Shock Absorber 2 1 Hardware Bag 3 Hardware Bag Contents Item # Quantity Reqd. Description
More informationI-317. AWWA Check Valves WARNING INSTALLATION AND MAINTENANCE INSTRUCTIONS SERIES 317 WARNING
Read and understand all instructions before attempting to install, remove, adjust, or perform maintenance on any Victaulic piping products Wear safety glasses, hardhat, and foot protection. Failure to
More information2005 Cadillac CTS BRAKES Disc Brakes - CTS
Removal Procedure 1. Inspect the fluid level in the brake master cylinder reservoir. 2. If the brake fluid level is midway between the maximum-full point and the minimum allowable level, no brake fluid
More information