KK-K9-F16-K INSTALLATION INSTRUCTIONS K9 Kit for FORD EXPLORER (Retail Model Vehicle with OEM Center Shifter Console)
|
|
- Cameron Davis
- 6 years ago
- Views:
Transcription
1 KK-K9-F16-K INSTALLATION INSTRUCTIONS K9 Kit for FORD EXPLORER (Retail Model Vehicle with OEM Center Shifter Console) TOOLS Needed: Phillips Screw Driver Power Drill with Drill Bits Trim panel removal tool Standard Socket set Wire Cutters /Crimpers Caulk Gun Metric Socket set Awl and 90 Scribe PARTS & HARDWARE: QTY DESCRIPTION PART # 1 Floor KNM Rear wall KNM Passenger side lower filler KNM Driver side lower filler KNM Front wall / bulkhead with sliding door KNM Ceiling KNM Lower B pillar bracket KNM Upper B pillar bracket KNM Rear floor bracket A KNM Rear floor bracket B KNM Front floor bracket KNM Passenger side upper filler KNM Driver side upper filler KNM Rubber Mat KNM Ceiling vent / duct KNM Driver side door panel DP-F18-1A 1 Passenger side door panel DP-F18-6A 1 Driver side hinged window guard WGI-F18-1-K9 1 Passenger side hinged window guard WGI-F18-6-K9 1 Dome Light Kit KK-K9-DOME-LED 1 Silicone caulk (sealant) PRM /4 x 3/4 Carriage bolt Stainless Steel GSM /4 serrated nut GSM /4 x 3/4 Phillips pan head screw - Stainless Steel GSM /4 Flat washer - Stainless Steel GSM /4 x 3/4 Hex head bolt GSM /4 Flat washer GSM #10 x 1/2 Phillips flat head sheet metal screws - SS GSM #10 x 1/2 Phillips pan head sheet metal screws - SS GSM #10 x 3/4 Phillips pan head sheet metal screws- SS GSM Rubber Bumper GSM MM nut GSM30201
2 NOTES! Read all instructions before installing any Havis, Inc. products. Use hardware provided with install kit. Vehicle battery should be disconnected during installation. It will need to be temporarily reconnected to move electric seats or check electric door locks. KK-K9-F16-K Assembly (Door panels and window guards not shown) KNM Upper B Pillar Bracket KNM Ceiling KNM Ceiling vent / duct KNM Passenger side upper filler KNM Lower B Pillar Bracket KNM Driver side upper filler KNM Front Wall KNM Rear Wall KNM Passenger side lower filler KNM Rear floor bracket A KNM Floor KNM Driver side lower filler KNM Rear floor bracket B
3 Remove rear passenger door panels first. Behind the door open paddle handle, remove plastic cover and bolt. (10mm socket) Underneath door handle, remove plastic cover and bolt. (10mm socket) Note: A small 90 scribe helps to pick plastic covers off. Remove screws at bottom of door panel. (7mm socket) Remove / unsnap entire door panel from door. (Trim removal tool) Disconnect latch cable from door handle. Remove door speaker. (7mm socket) Remove window switch from door panel and reattach it to original plug. Neatly wire tie the speaker wire, switch wire with switch inside the speaker cavity so it does not interfere with the window operation. Carefully remove the door lock rod from O.E.M. lock assembly or loosely wire tie it out of the way. NOTE: It is very important that lock rod does not prevent the electric lock from working. Removing the rod is recommended NOTE: It is very important to check the lock operation several times before installing the new K9 door panel. To simulate the door closing, Use a tool to close the latch mechanism. Use exterior handle to open latch.
4 Make sure O.E.M. door parts are secure and locks and windows are operational by using front door controls. Fold seats up in order to access the seat floor mounting hardware. Middle seats have a total of four (4) bolts and four (4) nuts to remove. Remove and save hardware for K9 front floor bracket. (15mm socket) Remove third seat forward brackets. Save nuts for K9 rear floor bracket. (13mm socket) Temporarily remove plastic panels to access the third seat rear brackets. Remove seat and seat belt bolts. (13mm socket) Temporarily remove (unsnap) rear cargo hatch door sill trim panel. Temporarily remove (unsnap) rear cargo side wall trim panels. NOTE: This is necessary in order to get rear seat out. Remove seat and replace seat bolts. (13mm socket) NOTE: Be very careful not to damage the rear air conditioning refrigerant lines. Replace all cargo trim panels. Interior is now ready for K9 equipment installation.
5 Place K9 kit door panel onto door. The top will hook onto rubber molding. Position so it lines up with the two existing (protruding) bolts. Drill mounting holes with 5/32 drill bit. Attach door panels with #10 x 3/4 Phillips pan head sheet metal screws. Attach rubber bumper to OEM door stud with 6mm nut. This will go on top of existing nut. Bumper is used as a stud guard. This step can be done before or after the door panel installation, but make sure the stud is center on the hole. NOTE: Window guards are shipped flat. On the edge of a work bench, bend a contour in the middle of the guard so it will fit tight against the window frame. Position window guard inside window frame. Use 5/32 drill bit and drill hinge mounting holes in door panel. Attach hinge with # 10 x 1/2 Phillips pan head sheet metal screws. With upper mount bracket attached to window guard, mark mounting hole locations in upper door / window frame. Drill 5/32 holes. Attach upper mount bracket with #10 x 1/2 Phillips flat head sheet metal screws. Door Panel and Window Guard complete. NOTE: It is very important to check the lock and window operation several times before closing door. Attach front bracket and rear floor bracket A with previously removed O.E.M. seat mount hardware. Tighten hardware. (13mm and 15mm sockets) Attach rear floor bracket B to K9 floor with 1/4 x 3/4 carriage bolts and serrated nuts. Tighten hardware. (7/16 socket)
6 Place floor into vehicle. Loosely attach rear floor bracket B to rear floor bracket A with 1/4 x 3/4 hex head bolts and flat washers. Note: Bracket A already has nutserts installed. Attach front floor bracket to K9 floor with 1/4 x 3/4 carriage bolts and serrated nuts. Tighten all floor hardware. (7/16 socket) Loosely attach rear wall to floor with 1/4 x 3/4 round head Phillips bolts and washers. Note: Floor already has nutserts installed. Remove O.E.M. grab handles on B pillar. Reuse original hardware and loosely attach front wall mounting brackets. (7mm socket) Attach front wall to B pillar brackets with 1/4 x 3/4 carriage bolts and serrated nuts. (7/16 socket) Loosely attach bottom of front wall to floor with 1/4 x 3/4 Carriage bolts and serrated nuts.. Loosely attach ceiling to front wall with 1/4 x 3/4 carriage bolts and serrated nuts. Loosely attach ceiling to rear wall with 1/4 x 3/4 carriage bolts and serrated nuts.
7 Determine correct driver and passenger side upper and lower filler panels. Loosely attach top filler panel to ceiling and rear wall with 1/4 x 3/4 carriage bolts and serrated nuts. Note: Filler panel flange goes behind wall and underneath ceiling as shown. Loosely attach lower filler to rear wall with 1/4 x 3/4 carriage bolts and serrated nuts. Attach filler to floor with 1/4 x 3/4 round head Phillips bolts and washers. Note: Filler panel flanges go in front of wall and floor as shown. Use an Awl or other pointed tool to help align mounting holes. After all parts are attached, double check and tighten all hardware. Adjust as necessary to minimize gaps. (7/16 socket or wrench and Phillips screwdriver) Insert ceiling vent / ducts and attach with #10 x 1/2 Phillips pan sheet metal screws. Vent / ducts will line up directly below the O.E.M. ceiling vents. Note: Make sure the O.E.M. vents are fully open. Insert and attach dome light to ceiling with #10 x 1/2 Phillips pan sheet metal screws. (connect wire before installing) Wire dome light to on/off switch. Switch location to be determined by the installer. K9 kits include an LED dome as of 1/3/2014 See instructions included with LED light. Neatly silicone / caulk the lower seams to shed water out of vehicle. Note: The floor pan is designed to minimize the need for sealant. Caulk (sealant) is mostly needed where the floor meets the door sill and lower filler panels.
8 Example mounting location for the optional Hot-N-Pop door gas spring. Example mounting location for the optional Hot-N-Pop exhaust fan. Note: Fan can be mounted to either side of the real wall. Fan does not mount to window guard. After silicone is dry (preferably overnight), place rubber mat into K9 insert. View of completed KK-K9-F16-K installation
K9-F17 INSTALLATION INSTRUCTIONS K9 Kit for FORD INTERCEPTOR SEDAN
K9-F17 INSTALLATION INSTRUCTIONS K9 Kit for 2013-2018 FORD INTERCEPTOR SEDAN TOOLS Needed: Phillips Screw Driver Trim panel removal tools Caulk Gun Standard Socket set Metric Socket set Wire Cutters /Crimpers
More informationK9-C23 INSTALLATION INSTRUCTIONS K9 Kit for CHEVY TAHOE PPV (9C1)
K9-C23 INSTALLATION INSTRUCTIONS K9 Kit for 2015-2018 CHEVY TAHOE PPV (9C1) TOOLS Needed: Phillips Screw Driver Trim panel removal tool Caulk Gun Standard Socket set Wire Cutters /Crimpers Drill & Drill
More information2 Rubber Bumper GSM MM nut GSM30201 K9-F18-PT_INST_4-16
K9-F18-PT INSTALLATION INSTRUCTIONS K9 Kit for 2013-2019 FORD INTERCEPTOR UTILITY Vehicle Notes: 1. For K9 applications, it is recommended to order the Interceptor Utility with the OEM optional Aux Rear
More informationINSTALL INSTRUCTIONS C-VS-1500-DUR-1 15 VEHICLE SPECIFIC CONSOLE for Dodge Durango with OEM Center Shifter
INSTALL INSTRUCTIONS C-VS-1500-DUR-1 15 VEHICLE SPECIFIC CONSOLE for 2011-2013 Dodge Durango with OEM Center Shifter TOOLS NEEDED: Phillips Screw Driver Standard Socket set Metric Socket set 90 Phillips
More informationINSTALLATION INSTRUCTIONS C-VS-2000-DUR-1 20 VEHICLE SPECIFIC CONSOLE for 2018 Dodge Durango with Standard Shifter
INSTALLATION INSTRUCTIONS C-VS-2000-DUR-1 20 VEHICLE SPECIFIC CONSOLE for 2018 Dodge Durango with Standard Shifter TOOLS REQUIRED: Phillips Screw Driver T-20 Torx bit Standard Socket set 9/64 Allen wrench
More informationTOOLS REQUIRED: Phillips Screw Driver Standard Socket set T-20 Torx Bit Metric Socket set Wire Cutters Wire Crimping tool
INSTALL INSTRUCTIONS C-VS-1200-INUT 2013-2018 FORD INTERCEPTOR UTILITY Fits Standard Interior and Optional Interior Upgrade (Code 65U) Vehicle Specific Console 12 inches of Equipment mounting space TOOLS
More informationINSTALL INSTRUCTIONS C-VS-1400-EQX-1 14 VEHICLE SPECIFIC CONSOLE for 2014 Chevy Equinox with OEM Center console
INSTALL INSTRUCTIONS C-VS-1400-EQX-1 14 VEHICLE SPECIFIC CONSOLE for 2014 Chevy Equinox with OEM Center console TOOLS NEEDED: Phillips Screw Driver Standard Socket set Metric Socket set Thin Tape T-20
More informationMOUNT BRACKET PARTS and HARDWARE: Installation parts with * come loose in hardware kit bag. Other parts are preassembled
INSTALL INSTRUCTIONS C-DMM-2006 Dash Monitor Mount 2017-2019 F-250, 350, 450 Pickup, F-450 and 550 Cab Chassis, 2015-2019 Ford F-150 and 2018-2019 Expedition Notes: 1. The C-DMM-2000 series Dash Monitor
More informationINSTALLATION INSTRUCTIONS FRONT PARTITION W/FILLER PANEL MOUNTING KIT
INSTALLATION INSTRUCTIONS FRONT PARTITION W/FILLER PANEL MOUNTING KIT P FRONT 1 with MFK 4 for 2008 2019 CHEVROLET PASSENGER VANS W/DUAL SIDE SWING OUT DOORS P FRONT 2 with MFK 8 for 2008 2019 CHEVROLET
More informationINSTALLATION INSTRUCTIONS C-DMM FORD INTERCEPTOR UTILITY SWING-OUT DASH MONITOR MOUNT
INSTALLATION INSTRUCTIONS C-DMM-123 2013-2018 FORD INTERCEPTOR UTILITY SWING-OUT DASH MONITOR MOUNT The Dash Monitor Mount bracket system requires two or three main parts that are sold separately. See
More informationTools Required: Phillips Screw Driver Standard Socket set T-20 Torx Bit Metric Socket set Wire Cutters Wire Crimping tool
INSTALL INSTRUCTIONS C-VS-1500-TAH-1 2015-2018 Chevy Tahoe Police Pursuit Vehicle (PPV) Vehicle Specific Console (9 inches wide) 15 inches of Equipment mounting space Note: 2 inches of mounting space is
More informationINSTALLATION & OWNER S MANUAL
INSTALLATION & OWNER S MANUAL CAB INSTALLATION INSTRUCTIONS KUBOTA GRAND L 30 SERIES HARD SIDED CAB ENCLOSURE (p/n 1KU3AS) SOFT SIDED CAB ENCLOSURE (p/n 1KU3SS) This Curtis Cab is designed and manufactured
More informationINSTALL INSTRUCTIONS C-VS-2000-TAH-2
INSTALL INSTRUCTIONS C-VS-2000-TAH-2 2015-2019 Chevy Tahoe Police Pursuit Vehicle (PPV) Vehicle Specific Console (12.5 inches wide) 20 inches of Equipment mounting space Tools Required: Phillips Screw
More informationINSTALLATION GUIDE P1000 PRO-CELL CURRENT FORD POLICE UTILITY INTERCEPTOR. pro-gard.com STRONG RELIABLE SECURE
INSTALLATION GUIDE P1000 PRO-CELL 2013 - CURRENT FORD POLICE UTILITY INTERCEPTOR STRONG RELIABLE SECURE THESE COMPONENTS ARE REQUIRED TO INSTALL THE PRO-GARD PARTITION SYSTEM WB4711-01D WB4711-01P 4K47UINTPRO
More informationINSTALLATION GUIDE P1000 PRO-CELL CURRENT FORD POLICE UTILITY INTERCEPTOR. pro-gard.com STRONG RELIABLE SECURE
INSTALLATION GUIDE P1000 PRO-CELL 2013 - CURRENT FORD POLICE UTILITY INTERCEPTOR STRONG RELIABLE SECURE THESE COMPONENTS ARE REQUIRED TO INSTALL THE PRO-GARD PARTITION SYSTEM WB4711-01D WB4711-01P 4K47UINTPRO
More informationINSTALL INSTRUCTIONS C-VS-2000-TAH Chevy Tahoe (Special Service) Vehicle Specific Console 20 inches of Equipment mounting space
INSTALL INSTRUCTIONS C-VS-2000-TAH-1 2007-2014 Chevy Tahoe (Special Service) Vehicle Specific Console 20 inches of Equipment mounting space Tools Required: Phillips Screw Driver Standard Socket set T-20
More informationINSTALLATION & OWNER S MANUAL
INSTALLATION & OWNER S MANUAL CAB INSTALLATION INSTRUCTIONS JOHN DEERE 4000 SERIES (4500/4600/4700) (4510/4610/4710) (4120/4320/4520/4720) HARD SIDED CAB ENCLOSURE (p/n 1JD4120AS) SOFT SIDED CAB ENCLOSURE
More informationINSTALLATION & OWNER S MANUAL
Rev. D, p. 1 of 14 INSTALLATION & OWNER S MANUAL Bobcat CT 230 and KIOTI CK30 cab kit with hard doors and soft rear curtain p/n 1BCT230 & 1KTCK30 The contents of this envelope are the property of the owner.
More informationWarning Do not attempt to install A/C units unless you are experienced with servicing A/C systems!
TOOLS REQUIRED: INSTALLATION INSTRUCTIONS PT-A-406 Rear HVAC System for 2014-2018 RAM PROMASTER without OEM rear AC/Heat Prep Package Fittings ***This system can also be used for a Promaster van with the
More informationINSTALLATION & OWNER S MANUAL
Rev. A, p. of 0 INSTALLATION & OWNER S MANUAL MASSEY FERGUSON GC2400 cab kit p/n MFGC2400 Installation Instructions The contents of this envelope are the property of the owner. Be sure to leave with the
More informationINSTALLATION INSTRUCTIONS C DMM Nissan Frontier SWING OUT DASH MONITOR MOUNT
INSTALLATION INSTRUCTIONS C DMM 134 2011 2018 Nissan Frontier SWING OUT DASH MONITOR MOUNT The Dash Monitor Mount bracket system may require two or three main parts that are Sold Separately. See web site
More informationINSTALLATION & OWNER S MANUAL
INSTALLATION & OWNER S MANUAL CAB INSTALLATION INSTRUCTIONS JOHN DEERE 3000 SERIES (4200/4300/4400) (4210/4310/4410) & (3120/3320/3520/3720) HARD SIDED CAB ENCLOSURE (p/n 1JD3520AS) SOFT SIDED CAB ENCLOSURE
More informationP/N Rev 01 04/14-1- NOTE: If you are ordering hinges for your rear doors, order and/or
REAR CANVAS DOOR KIT 900 XP RANGER CREW P/N 2879899 Application RANGER 900 XP CREW Before you begin, read these instructions twice and check to be sure all parts and tools are accounted for. Please retain
More informationPart Number: S-H-BAG-8 & S-H-8-RFEN Description: Saddlebags & Rear Fender / Undertail Fitment: Suzuki GSX 1300-R Hayabusa Revision: 1
Part Number: S-H-BAG-8 & S-H-8-RFEN Description: Saddlebags & Rear Fender / Undertail Fitment: 2008-2009 Suzuki GSX 1300-R Hayabusa Revision: 1 Tools Required Phillips head screwdriver Small screwdriver
More informationINSTALLATION & OWNER S MANUAL
Rev. E p. of 3 INSTALLATION & OWNER S MANUAL V446 Front Cab Kit and V446 Rear Cab Kit for RTV 40 INSTALLATION & OWNER S MANUAL The contents of this envelope are the property of the owner. Be sure to leave
More informationInstructions for 2-row monitoring only
Installation Instructions for CaseIH cotton picker models: Instructions for 2-row monitoring only Ensure the model numbers shown above correspond to the machine model. If you receive the incorrect installation
More informationINSTALLATION & OWNER S MANUAL
Rev. C, p. of 2 INSTALLATION & OWNER S MANUAL KUBOTA B2650/3350 Hard Sided Cab p/n KB33AS Soft Sided Cab p/n KB33SS Installation Instructions The contents of this envelope are the property of the owner.
More informationTools Required: Phillips Screw Driver Standard Socket set T-20 Torx Bit Metric Socket set Wire Cutters Wire Crimping tool
INSTALL INSTRUCTIONS C-VS-1013-TAH-1 2015-2018 Chevy Tahoe Police Pursuit Vehicle (PPV) Vehicle Specific Console (9 inches wide) 23 inches of Equipment mounting space Tools Required: Phillips Screw Driver
More informationINSTALLATION & OWNER S MANUAL
Rev. C p. 1 of 21 INSTALLATION & OWNER S MANUAL F5205 HARD SIDED CAB KIT INSTALLATION & OWNER S MANUAL The contents of this envelope are the property of the owner. Be sure to leave with the owner when
More informationINSTALLATION INSTRUCTIONS FORD PI UTILITY SINGLE CELL
13-15 FORD PI UTILITY SINGLE CELL 475-0318 13-15 FORD PI UTILITY SINGLE CELL 475-0318 Headliner Front Upper Poly Window Extruded Backbone Center Tube Bracket Center Stiffener Tube ABS Seat Center Upper
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Accessory Application Publications No. CD CHANGER ATTACHMENT KIT 2005 CIVIC SI AII 27936 Issue Date AUG 2004 PARTS LIST CD Changer Attachment Kit (sold separately): P/N 08B26-S5T-100
More informationHARD TRI-FOLD COVER SPECIAL BOLT ON SIDE RAIL INSTRUCTIONS 2016-ON TOYOTA TACOMA 6 BOX
HARD TRI-FOLD COVER SPECIAL BOLT ON SIDE RAIL INSTRUCTIONS 2016-ON TOYOTA TACOMA 6 BOX Read and follow these special instructions along with the standard instructions carefully before installing or using
More informationINSTALLATION & OWNER S MANUAL
INSTALLATION & OWNER S MANUAL INSTALLATION INSTRUCTIONS KAWASAKI MULE 4000 TRANS 4 FRONT CAB KIT (p/n: KAF40T-001WA and p/n: KAF40T-001BA) NOTE: Hard sided doors, soft sided doors, and rear cab are sold
More informationMERCEDES METRIS PARTITION INSTALLATION INSTRUCTIONS
MERCEDES METRIS PARTITION INSTALLATION INSTRUCTIONS www.sortimo.knapheide.com www.sortimo.knapheide.com The following instructions detail the procedure for installing a Sortimo By Knapheide Partition in
More informationINSTALLATION & OWNER S MANUAL
INSTALLATION & OWNER S MANUAL CAB INSTALLATION INSTRUCTIONS MASSEY FERGUSON THX FOR MASSEY FERGUSON 528, 53, AGCO ST28A, ST33A, CHALLENGER MT255B SOFT SIDED CAB ENCLOSURE (p/n MFTHXSS) This Curtis Cab
More informationHiBoy Maverick/Commander Doors Part # HiBoy4 Maverick/Commander Doors Black
Racing 3191 N Washington St. Suite 2 Chandler, AZ 85225 1 (800) 708-9803 http://www.racing.com HiBoy Maverick/Commander Doors Part # 07-2001 HiBoy4 Maverick/Commander Doors Black Congratulations on your
More informationINSTALLATION & OWNER S MANUAL
INSTALLATION & OWNER S MANUAL INSTALLATION INSTRUCTIONS KAWASAKI MULE 4000 CAB KIT (p/n: KAF40-005WA and KAF40-005BA) NOTE: Hard sided doors are sold separately. This manual is the property of the owner.
More informationINSTALLATION & OWNER S MANUAL
INSTALLATION & OWNER S MANUAL CAB INSTALLATION INSTRUCTIONS FOR E-Z-GO MPT BALL CAGE (p/n 72685-G01) The contents of this envelope are the property of the owner. Be sure to leave with the owner when installation
More informationINSTALLATION INSTRUCTIONS CATCH CAN KIT
INSTALLATION INSTRUCTIONS CATCH CAN KIT FORD FOCUS Document: 19-0150 Support: info@radiumauto.com STEPS 1 TO 19 COVER THE PCV SIDE CATCH CAN KIT (P/N: 20-0315) STEPS 20-32 COVER THE CRANKCASE CATCH CAN
More informationINSTALLATION & OWNER S MANUAL
INSTALLATION & OWNER S MANUAL CAB INSTALLATION INSTRUCTIONS JOHN DEERE 4000 SERIES (4500/4600/4700) (4510/4610/4710) (4120/4320/4520/4720) HARD SIDED CAB ENCLOSURE (p/n 1JD4120AS) SOFT SIDED CAB ENCLOSURE
More informationINSTALL INSTRUCTIONS C-VS-0812-TAH-1
INSTALL INSTRUCTIONS C-VS-0812-TAH-1 2015-2018 Chevy Tahoe Police Pursuit Vehicle (PPV) Vehicle Specific Console with 20 inches of Equipment mounting space Tools Required: Phillips Screw Driver Standard
More informationINSTALLATION INSTRUCTIONS JEEP 2011-UP JK SECURITY FULL CONSOLE #274
INSTALLATION INSTRUCTIONS JEEP 2011-UP JK SECURITY FULL CONSOLE #274 PARTS CHECKLIST Tuffy Console #9 Left Front Mounting Bracket #10 Right Front Mounting Bracket #11 Electronics mounting bracket #12 Divider
More informationHARD TRI-FOLD COVER SPECIAL BOLT ON SIDE RAIL INSTRUCTIONS 2016-ON TOYOTA TACOMA 5 BOX
HARD TRI-FOLD COVER SPECIAL BOLT ON SIDE RAIL INSTRUCTIONS 2016-ON TOYOTA TACOMA 5 BOX Read and follow these special instructions along with the standard instructions carefully before installing or using
More informationINSTALLATION & OWNER S MANUAL
INSTALLATION & OWNER S MANUAL CAB INSTALLATION INSTRUCTIONS JOHN DEERE GATOR HPX and/or XUV HARD SIDED CAB ENCLOSURE (p/n: 1GTR44AS) SOFT SIDED CAB ENCLOSURE (p/n: 1GTR44SS) 111 HIGGINS STREET, WORCESTER,
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Honda Dealer: Please give a copy of these instructions to your customer. PARTS LIST (15) (8) (12) (14) (13) (10) (11) (18) (17) (1) Accessory Application Publications No. TRX500FA/FGA
More informationTrident Universal. Installation Manual
Trident Universal Installation Manual Revision 1.1; Updated: July 6, 2017 Table of Contents Tool List 03 Installation Tool List Pre-Install Preparation 04 Lateral Panel Modifications 07 Top Panel Modifications
More informationINSTALLATION & OWNER S MANUAL
INSTALLATION & OWNER S MANUAL CAB INSTALLATION INSTRUCTIONS FOR MASSEY FERGUSON 233, 428v (gear), 428v (hydro) SOFT SIDED CAB ENCLOSURE (p/n: MF233SS) This Curtis Cab is designed and manufactured for use
More informationINSTALLATION INSTRUCTIONS CATCH CAN KIT
INSTALLATION INSTRUCTIONS CATCH CAN KIT FORD FOCUS Document: 19-0150 Support: info@radiumauto.com STEPS 1-19 COVER THE PCV SIDE CATCH CAN KIT (P/N: 20-0315) STEPS 20-32 COVER THE CRANKCASE CATCH CAN KIT
More informationLPE C5 Battery Relocation Kit
LPE C5 Battery Relocation Kit The LPE C5 Corvette battery relocation kit improves vehicle weight distribution by moving weight to the rear of the vehicle. The improved weight distribution increases traction
More information(2) #10 Washers (1) ¼ Washers (6) 5/16 Washers (2) Locknuts (2) 5/16 Locknuts
INSTALLATION INSTRUCTIONS TJ Speaker / Storage Security Console #066 Please read and fill out the enclosed warranty registration card to activate your warranty. SHIPMENT CONTENTS Console Front Shift Lever
More informationFactory Five Racing, Inc. 818 Kit Assembly manual revision 1i update
Factory Five Racing, Inc. 818 Kit Assembly manual revision 1i update Pedal box...1 Cable Accelerator Pedal (2002-2005)...2 OEM seats...7 Windshield... 13 Center console... 19 Pedal box Attach the pedal
More informationRef Qty Part Description Part Number -1- Kit ( ) Contents:
REAR CANVAS DOOR KIT 900 XP RANGER CREW P/N 2879899 Application RANGER 900 XP CREW Before you begin, read these instructions twice and check to be sure all parts and tools are accounted for. Please retain
More informationConflicts None. TOYOTA TUNDRA 2017 Black Laser Cut Grille. Part Number: Accessory Code: BG3000. General Applicability
TOYOTA TUNDRA 2017 Black Laser Cut Grille Part Number: 00016-34173 Accessory Code: BG3000 Conflicts None Kit Contents Item # Quantity Reqd. Description 1 1 Laser Cut Grille 2 1 Complete hardware kit General
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Accessory TRAILER HITCH Application 2011 ODYSSEY Publications No. AII 43937 Issue Date SEP 2010 PARTS LIST Trailer Hitch Kit P/N 08L92-TK8-100 Trailer Hitch Harness Kit P/N 08L91-TK8-100
More informationCONVENTIONAL PARTS MANUAL. Door Section. Page 4-1. Doors 07/97
Doors Page 4-1 Stepwell - Outward Opening Door Page 4-2 Doors Stepwell - Outward Opening Door Item Part Num. Number Qty. Description Notes 1 47001449 1 Trim - Step, Entrance, Diamond Plate 2 47001450 1
More informationKUBOTA BX-1500/1800/2200 HARD SIDED CAB (p/n 1KBXAS) SOFT SIDED CAB (p/n 1KBXSS)
TRACTOR CAB INC. 111 HIGGINS STREET, WORCESTER, MA 01606 KUBOTA BX-1500/1800/2200 HARD SIDED CAB (p/n 1KBXAS) SOFT SIDED CAB (p/n 1KBXSS) INSTALLATION AND OWNER S MANUAL The contents of this envelope are
More informationINSTALLATION & OWNER S MANUAL
Rev. B, p. 1 of 25 INSTALLATION & OWNER S MANUAL POLARIS RANGER RCS (for models XP or HD) (for model years 2009-) cab without doors kit (p/n 1POLRCWD) cab with doors kit (p/n 1POLRC) doors only kit (p/n
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Accessory Application Publications No. All 30528 INTERFACE 2006 CR-V Issue Date SEP 2005 PARTS LIST XM Radio Unit Kit (sold separately): P/N 08A15-EX5-000 2 Wire tie with clips
More informationInstructions for 2-row monitoring only
Installation Instructions for CaseIH cotton picker models: Instructions for 2-row monitoring only CAUTION: Ensure the model numbers shown above correspond to the machine model. If you receive the incorrect
More informationINSTALLATION INSTRUCTIONS DRAWERS #240
INSTALLATION INSTRUCTIONS DRAWERS #240 Please read and fill out the enclosed warranty registration card to activate your warranty. SHIPMENT CONTENTS #1 Lid #2 Rear #3 Left side panel #4 Right side panel
More informationFactory Five Racing, Inc. 818 Kit Assembly manual revision 1J update
Factory Five Racing, Inc. 818 Kit Assembly manual revision 1J update Turbo coolant overflow tank...1 Shifter handle...4 Install...4 Door skin...7 Door Liner... 10 Side mirrors... 14 Door handles and pulls...
More informationINSTALLATION & OWNER S MANUAL
p. 1 of 15 INSTALLATION & OWNER S MANUAL YANMAR Sc2450 cab kit with hard doors and soft rear curtain Curtis p/n: 1CYSC2450AS The contents of this envelope are the property of the owner. Be sure to leave
More informationInstallation Instructions. Attention Dealers: Please give this owners manual to the customer when the product is delivered.
Serving the Truck & Trailer Industry Since 1944 Attention Dealers: Please give this owners manual to the customer when the product is delivered. Call 800-535-9545 www.aeroindustries.com Indianapolis, IN
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Accessory TRAILER HITCH Application 2012 ODYSSEY Publications No. AII 46755 Issue Date SEP 2011 PARTS LIST Trailer Hitch Kit P/N 08L92-TK8-100 Trailer Hitch Harness Kit P/N 08L91-TK8-100
More informationGENUINE PARTS INSTALLATION INSTRUCTIONS
GENUINE PARTS INSTALLATION INSTRUCTIONS 1. 2. 3. 4. DESCRIPTION: APPLICATION: PART NUMBER: KIT CONTENTS: Accent light Kit Versa Note 999F3 4Z000 - Accent Lighting Kit. 999Q9 AY000 - Accessory Service Connector
More informationINSTALLATION & OWNER S MANUAL
INDUSTRIES, LLC. INSTALLATION & OWNER S MANUAL CAB INSTALLATION INSTRUCTIONS KUBOTA GRAND L 40 SERIES HARD SIDED CAB ENCLOSURE (p/n 1KGL4AS) This Curtis Cab is designed and manufactured for use only as
More informationOwner smanual. Banks Ram-Air Super-Scoop Chevy/GMC Pickups. with Installation Instructions
Owner smanual with Installation Instructions Banks Ram-Air Super-Scoop 2007-2013 Chevy/GMC Pickups THIS MANUAL IS FOR USE WITH SYSTEM 42235, 42236 & 42237 Gale Banks Engineering 546 Duggan Avenue Azusa,
More informationINSTALLATION & OWNER S MANUAL
INSTALLATION & OWNER S MANUAL This Curtis Cab is designed and manufactured for use only as reasonable weather protection. This cab is not applicable, Nor should the cab be considered as protection against
More informationT2 Terminal Tractor Service Bulletin
T2 Terminal Tractor Service Bulletin Subject: Updated HVAC Wiring Harness, T2's Terminal Tractors Product: Medium Terminal Tractor Bulletin # SB18TI0090 Date: Pages: 7-August-2018 Page 1 of 11 Units Affected:
More informationINSTALLATION & OWNER S MANUAL
Rev. R p. 1 of 16 INSTALLATION & OWNER S MANUAL V4211 HARD SIDED CAB KIT and/or V4275 CAMO HARD SIDED CAB KIT INSTALLATION & OWNER S MANUAL The contents of this envelope are the property of the owner.
More information2015 Ford F150 Rear Bumper w/ LED
2015 Ford F150 Bumper w/ LED T527990 T527991 PARTS LIST: 1 Bumper Assembly 4 12mm Lock Washers 2 Mounting Brackets 6 12 mm Nylon Lock Nuts 4 Sensor Hole Plugs 8 4mm x 10mm Button Head Bolts 2 Plastic Plugs
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Accessory TRAILER HITCH Application 2011 ODYSSEY Publications No. AII 43937 Issue Date SEP 2010 PARTS LIST Trailer Hitch Kit P/N 08L92-TK8-100 Trailer Hitch Harness Kit P/N 08L91-TK8-100
More informationINSTALLATION & OWNER S MANUAL
INSTALLATION & OWNER S MANUAL CAB INSTALLATION INSTRUCTIONS MASSEY FERGUSON TGX SERIES SOFT SIDED CAB ENCLOSURE (p/n MFTGXSS) This Curtis Cab is designed and manufactured for use only as reasonable weather
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Accessory TRAILER HITCH Application 2014 ODYSSEY Publications No. AII 49544 Issue Date JUNE 2013 PARTS LIST Bumper edge trim Trailer Hitch Kit P/N 08L92-TK8-100 Trailer hitch
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Accessory S Application 2011 PILOT Publications No. AII 43298 Issue Date MARCH 2010 PARTS LIST Back-up Sensor Attachment Kit P/N 08V67-SZA-100A Back-up sensor harness Fuse label
More informationHUMMER H A. 3-5 Hours INSTALLATION GUIDE INSTALLATION TIME SKILL LEVEL. 4= Experienced TOOLS REQUIRED APPLICATION MODEL YR PART #
INSTALLATION GUIDE APPLICATION MODEL YR PART # HUMMER H2 2003-2009 75107-01A INSTALLATION TIME 3-5 Hours Professional installation recommended SKILL LEVEL 1 2 3 = Experienced TOOLS REQUIRED Safety goggles
More informationC15C C15C. Page 1 of 20
2 x Lid Front Hinge 1135 8 x M8 Bolt 8 x M8 Washer (3mm Thick) 4 x M6 Large washers 4 x M6 Spring washers 4 x M6 x 40mm Bolts 6 x M6 20mm Bolts 6 x M6 Washers 20 x Screws 2 x Lid mount gas strut bracket
More informationSPECIAL INSTALLATION INSTRUCTIONS
SPECIAL INSTALLATION INSTRUCTIONS WARN 4X FLARES FRONT AND REAR '98 TOYOTA HILUX DUAL-CAB As you read these instructions, you will see NOTES, CAUTIONS and WARNINGS. Each message has a specific purpose.
More informationINSTALLATION MANUAL
INSTALLATION MANUAL 2563000 Parts List 1 Carrier weldment 2 Support arm assembly 1 Third brake light assembly 1 Light extension bracket 1 Spare tire adjustment plate 1 Spare tire mount plate 1 Female spade
More informationINSTALLATION INSTRUCTIONS
AUTOMOTIVE PRODUCTS, INSTALLATION INSTRUCTIONS SPORTSMAN WINCH MOUNT GRILLE GUARD / MAX WINCH TRAY HDX WINCH MOUNT GRILLE GUARD APPLICATION: 2017 Ford F250/350 Super Duty PART NUMBER: 40-93905, 45-93900,
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Accessory S P/N 08V67-SJC-101 Application 2012 RIDGELINE Publications No. AII 12006 Issue Date NOV 2011 PARTS LIST Back-up sensor harness 3 Wire ties with small clips (2 Not used)
More informationINSTALLATION & OWNER S MANUAL
Rev. L, p. 1 of 18 INSTALLATION & OWNER S MANUAL KUBOTA L3200, L3800, and L2501 WorkPro Hard Sided Cab (p/n: 1KL38AS) WorkPro Soft Sided Cab (p/n: 1KL38SS) An optional Hard Rear Panel can be purchased
More informationASSEMBLY & INSTALLATION INSTRUCTIONS
ASSEMBLY & INSTALLATION INSTRUCTIONS VEHICLE MOUNT KIT 99101087 AND VEHICLE CENTER MEMBER For 26 Series: 99100890 TO FIT 2009 & Later FORD F150 4x4 (without EcoBoost V6) 2011 & Later FORD F150 4x4 (with
More informationProcharger Stage II Intercooled Supercharger System (11-14 GT)
Procharger Stage II Intercooled Supercharger System (11-14 GT) Installation Time: Approximately one day. Installed on 2012 Mustang GT 5.0/Manual Required Tools 3/8 Socket Set (Standard and Metric) 1/2
More informationPHASE 3 POWERSPORTS AUDIO KIT RZR POLARIS. pg 2 Disassembly, Wire and Amplifier Plate Installation. pg 9 Glovebox Subwoofer Installation
POLARIS RZR PHASE 3 POWERSPORTS AUDIO KIT pg 2 Disassembly, Wire and Amplifier Plate Installation pg 9 Glovebox Subwoofer Installation pg 13 Kick Panel Speakers Installation pg 25 MRB3 and Dash Kit Installation
More informationINSTALLATION OF THE ENCLOSURE FOR THE MULE 3010 TRANS INSTALLATION GUIDE FOR THE MULE 3000 TRANS ENCLOSURE P. 1. Sept 07
INSTALLATION GUIDE FOR THE MULE 3000 TRANS ENCLOSURE P. 1 INSTALLATION OF THE ENCLOSURE FOR THE MULE 3010 TRANS Sept 07 www.essexmfg.com PO Box 92864 Southlake, TX 76092 Ph:888-643-7739 INSTALLATION GUIDE
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Accessory HITCH Application 2009 CR-V Publications No. AII 40373 Issue Date AUG 2008 PARTS LIST Plain washer, 12 mm Trailer Hitch Kit P/N 08L92-SWA-100 Trailer hitch 6 Spring
More informationSALEEN SPEEDLAB BOOST AND WATER TEMPERATURE GAUGE POD KIT
= SALEEN SPEEDLAB BOOST AND WATER TEMPERATURE GAUGE POD KIT INSTALLATION MANUAL: 2005-09 Mustang 4.6L 3V P/N: 10-8002-C12000B KIT P/N: 10-2903-B11511* Saleen Performance, Inc. 1225 East Maple Rd. Troy,
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Accessory S P/N 08V67-SJC-101 Application 2010 RIDGELINE Publications No. AII 42117 Issue Date AUG 2009 PARTS LIST Back-up sensor harness 3 Wire ties with small clip (2 Not used)
More informationISNORKEL034XLT FORD PX RANGER XLT 9/2011-7/ & 3.2L DIESEL FORD PX RANGER Mk II XLT 7/ & 3.2L DIESEL
INSTALLATION GUIDE ISNORKEL034XLT FORD PX RANGER XLT 9/2011-7/2015 2.2 & 3.2L DIESEL FORD PX RANGER Mk II XLT 7/2015+ 2.2 & 3.2L DIESEL Ironman 4x4 Snorkel fits to the right hand side of the Ford PX Ranger
More information2-row and All-row systems included.
Ag Leader Technology Cotton Picker Installation Installation Instructions for John Deere cotton picker models: 2-row and All-row systems included. IMPORTANT: Ensure the model numbers shown above correspond
More informationFor Honda Big Red. Caution: Before using this product, read this manual and follow all safety instruction. Defender Cab Owner s Manual.
Defender Cab Owner s Manual Model: Honda Big Red Caution: Before using this product, read this manual and follow all safety instruction For Honda Big Red Safety Instructions Kit Contents Tool Requirement
More informationLevel of Difficulty Easy. Product Image. Front Mounting Bracket (553204) AC Mounting Bracket (553211) Tools Required Socket, 1/2"
INSTALLATION MANUAL Parts List 3 2 1 1 1 3 2 4 13 16 13 16 2 2 14 Front Mounting Bracket Middle Mounting Bracket Rear Mounting Bracket AC Mounting Bracket AC Top Mounting Bracket U-Bolt 3" U-Bolt 3.75"
More information11381 INSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Safety glasses should be worn at all times while installing this product. YEARS: 0-CURRENT MAKE: BMW MODEL: -SERIES STYLE: SEDAN WARNING: NEVER EXCEED YOUR VEHICLE MANUFACTURER'S
More informationSAFETY THIS PRODUCT IS FOR OFFROAD USE ONLY. ALL LIABILITY FOR INSTALLATION AND USE RESTS WITH THE OWNER.
Installation Instructions SAFETY Your safety and the safety of others is very important. In order to help you make informed decisions about safety, we have provided installation instructions and other
More informationScion xa SATELLITE RADIO TUNER Preparation
Preparation Part Number: PTS31-00051 Kit Contents Item # Quantity Reqd. Description 1 1 Antenna, Interior 2 1 Antenna Tape Pad 3 1 Wire Harness 4 1 Bracket, Floor 5 3 Hardware Bags 6 3 Templates 7 1 SIRIUS
More informationTABLE OF CONTENTS INTRODUCTION 3. INSTALLATION PROCEDURES Air Conditioner Location 4. A/C Ducting Installation 5
585474 1 TABLE OF CONTENTS SECTION PAGE INTRODUCTION 3 INSTALLATION PROCEDURES Air Conditioner Location 4 Air Conditioner Mounting 4 A/C Ducting Installation 5 Power Kit Installation (Batteries). 5 Separator...
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Accessory Application CR-V Publications No. AII 32953-34081 Issue Date NOV 2006 PARTS LIST 2 Corner sensor clips Backup Sensor Attachment Kit P/N 08V67-SWA-100A Back-up sensor
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Accessory Application Publication No. WINCH MOUNT P/N 08L74-HR3-A20 After 13 TRX420 (All except TRX420FA/FPA) After 13 TRX500 (All except TRX500FA/FPA) MII 15067 Issue Date Revised:
More informationRemove the rear tire and the (8) 13mm bolts holding the tire carrier to the tailgate. Remove the 3rd brake light wiring harness.
J108781 2 4 Rear Bumper & Tire Carrier & Optional Flood Lights Jeep Wrangler JK (2007-2017) Tools Required: Basic Hand Tools 35mm Socket Tape Measure Grease Gun Straight Edge Remove the rear tire and the
More information