INSTALLATION & OWNER S MANUAL

Size: px
Start display at page:

Download "INSTALLATION & OWNER S MANUAL"

Transcription

1 Rev. R p. 1 of 16 INSTALLATION & OWNER S MANUAL V4211 HARD SIDED CAB KIT and/or V4275 CAMO HARD SIDED CAB KIT INSTALLATION & OWNER S MANUAL The contents of this envelope are the property of the owner. Be sure to leave with the owner when installation is complete. APPROXIMATE INSTALLATION TIME: 3-5 HOURS NOTE: V4211 Hard Sided Cab Kit shown NOTE: hard sided cab shown with the following optional accessories: work lights, strobe light, and windshield wiper. manual p/n (revised: 1/2/2008)

2 Rev. R p. 2 of 16 Exposure to Carbon Monoxide can Cause illness, serious injury or death. Never operate vehicle if suspicious of Carbon Monoxide. Inspect exhaust system for leaks monthly. Leaks can result from loose connections, corrosion, cracks or other damage to the exhaust manifold. If leaks are found, repair or replace exhaust system. Do not use vehicle until repair or replacement is complete. This cab is designed and manufactured for use only as reasonable weather protection. This cab is not applicable, nor should the cab be considered as protection against roll over, collision or other accidents that may result. This cab is NOT a R.O.P.S. cab. Extreme care should be taken when operating and by qualified, experienced operators only. ADDED WEIGHT Cabs, blades and general accessories add additional weight to the base vehicle. All accessory weights are listed in product brochures. Deduct the accessory's total weight from the vehicle's rated capacity and never exceed the vehicle's rated capacity including driver and passenger.

3 CAB INSTALLATION BEFORE YOU START HELPFUL REMINDERS: A. Refer to parts diagram toward the back of this manual to help identify parts during the assembly process. B. Leave all bolts loose for later adjustment unless otherwise specified. NOTE: DO NOT DIMPLE METAL ROOF BY OVERTIGHTENING FASTENERS. C. Read and understand all instructions before beginning. D. If installing accessories, read all accessory instructions before starting cab assembly. E. If installing overhead console, bench install the radio antenna onto the roof before putting the roof in place. Finish wiring accessories to overhead console before bolting roof in place. F. Plastic washers have been supplied to provide a weather seal around all exterior fasteners. The plastic washer should be installed under each bolt head directly against the outside cab surface. Care should be taken not to over tighten the fasteners and damage the plastic washer. Also use flat washers as required. G. Apply a clear silicone sealant to seal any minor gaps that may occur due to vehicle variances. TOOLS REQUIRED: Rev. R p. 3 of 16 7/16 SOCKET (1/4 DRIVE) 1/4 DRIVE RATCHET 3/8 DRIVE RATCHET 1/2 SOCKET (3/8 DRIVE) 3/4 OPEN END WRENCH 1/2 OPEN END WRENCH 7/16 OPEN END WRENCH

4 Rev. R p. 4 of 16 NOTE: If installing heater kit V4214(A), install foam seal from kit before installing windshield. 1. INSTALL WINDSHIELD ASSEMBLY 1.1 With assistance, place the windshield assembly on the front of the vehicle and attach with the following: 2 lower mounting brackets, four 5/16 x 3/4 long hex head bolts, and 4 flat washers. (see Fig. 1.1) NOTE: do not fully tighten these four (4) hex head bolts until step Place a formed rubber spacer between windshield top and front horizontal tube at four double hole locations. (see Fig. 4.1) Fig. 1.1 Inside view of Windshield Assembly

5 Rev. R p. 5 of INSTALL REAR PANEL ASSEMBLY NOTE: remove protective film from rear panel. 2.1 With assistance, place the rear panel assembly on the back of the vehicle and attach with the following: 2 lower mounting brackets, four 5/16 x 3/4 long hex head bolts, and 4 flat washers. (See Fig. 2.1) NOTE: do not fully tighten these four (4) hex head bolts until the roof is installed in step Place a formed rubber spacer between the rear panel top and the horizontal tube at each set of holes. (see Fig. 2.1 and 4.1) Fig. 2.1 Inside view of Rear Panel Assembly 3. INSTALL DOOR RECEIVERS 3.1 Install each door receiver so that the bent, rectangular tubing is on the outer side of the cab (see photo at right), and the end with the single mounting slot is towards the front of the vehicle. Attach to the windshield assembly using one 5/16-18 x 3/4 long hex head bolt and flat washer, and to the rear panel assembly using two 5/16-18 x 3/4 long hex head bolts and flat washers. (NOTE: front and rear assemblies have factory installed threaded inserts in the tubing). Repeat procedure for opposite side. Do not tighten bolts at this time. tubing to be flush

6 4. INSTALL ROOF MOUNT & ROOF Rev. R p. 6 of 16 NOTE: If installing an overhead console, place the unit in position on the vehicle s two frame tubes that run front to back. Final position the back edge of the overhead console even with the front of roof cross stiffener. Feed the wire for the wiper motor (from the overhead console) over the vehicle s upper, front, tubular frame, and beneath the windshield top before tightening any of the windshield assembly mounting bolts (see photo at right). Bench install the radio antenna onto the roof before putting the roof in place. Read all additional accessory instructions and finish wiring all accessories to overhead console before bolting roof in place. 4.1 With assistance, attach the windshield assembly and the roof mount to the vehicle s tubular frame with the following: 4 U bolts, 4 molded rubber spacers, 8 flat washers, and 8 locknuts. (see Fig. 4.1) NOTE: orient the roof mount as wiper wires shown with the Z bend towards the front, and centered so that the U bolts are equally spaced outside the two overhead frame tubes. Align the roof mount so that it is parallel with the top of the windshield. Tighten locknuts snugly being careful not to overcompress the rubber spacers. 4.2 With assistance, place the roof in position, with the long angled visor portion to the front as shown in Fig Attach the rear of the roof with the following: 2 U bolts, 2 molded rubber spacers, 4 nylon washers, 4 flat washers, and 4 locknuts. (see Fig. 4.1) Do not tighten these four locknuts. 4.4 The front of the roof attaches to the roof mount with the following: four 5/16-18 x 3/4 long hex head bolts, 4 nylon washers, 8 flat washers, and 4 locknuts. NOTE: flat washers and locknuts go underneath the flange of the roof mount as shown in Fig Do not tighten these four locknuts. 4.5 Secure the middle of the roof with two U bolts, 4 nylon washers, 4 flat washers, and 4 locknuts. NOTE: DO NOT DIMPLE METAL ROOF BY OVERTIGHTENING. Fig. 4.1 Side view of Roof

7 Rev. R p. 7 of INSTALL ROOF MOUNT & ROOF ((cont d.) 4.6 Tighten all nuts and bolts, including the 6 upper bolts for the door receivers, and the 8 lower bolts for the mounting brackets. NOTE: where there is a molded rubber spacer, tighten the locknuts snugly, being careful not to overcompress the rubber. DO NOT DIMPLE METAL ROOF BY OVER- TIGHTENING. 4.7 Install 18 nut covers on the 8 locknuts and 4 bolt heads on the top, exterior side of the roof, and on the six locknuts on the windshield hinges. 5. INSTALL STRIKER MOUNTS 5.1 Install striker mounts as shown in Fig Use 5/16 x 3/4 long hex head bolts and flat washers to attach the striker mount to the inside of the lower, front tubing of the windshield assembly where there are factory installed threaded inserts. Install striker bolt in striker mount as shown below. (NOTE: finger guard to end up being centered and facing inwards.) Repeat procedure for opposite side. Fig. 5.1 Inside view of driver s side

8 Rev. R, p. 8 of 16 IMPORTANT NOTICE! The enclosed door hinges must be installed and adjusted accurately for proper door performance including the prevention of hinge fatigue and/or premature wear of the striker bolt. 6. INSTALL DOOR HINGES Install right side door hinges per figures 1 and 2, use 1 1/2 long bolts to install the pin hinges to the outside surface of the curved rear tube as shown, paying careful attention to the pin orientation in fig. 1. The head of each rear tube bolt, the washer, and the tube spacer should all be towards the inside of the cab as shown in fig ure 2. Locknuts to be towards the outside of the cab. Leave bolts loose for now. On a flat, padded working surface, install the hinge sleeves to the exterior of the door as shown in fig. 2. Use 1-1/2" long bolts and hinge plates. Discard any extra bolts. The head of each bolt and the hinge plates are to be on the inside surface of the door with the locknuts towards the outside surface of the door as shown in fig. 2. Leave bolts loose for now. Apply lubricant (preferably grease) to the pins. With assistance, install the door onto the pin hinges by guiding both hinge sleeves onto their respective pin hinges as shown. NOTE: with the door in hand, approach the pin hinges from approximately a 45 degree angle from the rear of the vehicle as shown in fig. 4 on the next page (so the roof will not interfere with door installation). Work the doors back and forth until the hinges are completely seated. CAUTION: be extremely aware of pinch points between upper door section and roof, as well as between the pin hinge and the hinge sleeves themselves. Repeat for left side of vehicle per figures 2 and 3 (again paying special attention to the pin hinge orientation shown in fig. 3). Fig. 1 Right side rear panel tube and door Fig. 2 Hardware Detail Fig. 3 Left side rear panel tube and door Per this straight line drawn up through fig. 1, use a straight edge to be sure the hinges are in line with each other when tightening bolts.

9 Rev. R, p. 9 of 16 Fig. 4 Door and roof clearance diagram 7. FINAL DOOR ADJUSTMENTS With the door loose, close and latch the door. Per fig. 1 on the previous page, use a straight edge to be sure the hinges are in line with each other. Tighten all hinge bolts. NOTE: Top of door should end up visually parallel with side of roof. Specific adjustments can be made as follows: (NOTE: an assistant will be needed to accomplish this step.) Per fig. 5, the 1/4-20 hex head bolts on the door hinges can be loosened on the rear tube, or on the door itself, or in both places, in order to slightly rotate the door or adjust up and down, front to back as necessary for proper alignment with the cab and front to back engagement of the latch with the striker pin. Keep the hinge sleeves fully seated on the pin hinges. Per fig. 6, the large striker bolt and nut can be loosened and reset for better engagement in the latch assembly if necessary. Use two 3/4 open end wrenches. (NOTE: finger guard to end up being centered and facing inwards.) NOTE: the latch is a rotary type with two positions to close. Adjust door so that when fully closing door latch clicks twice for total engagement. CAUTION: FOR SAFE OPERATION, DO NOT DRIVE WITH DOORS OPEN. MAKE SURE DOORS ARE CLOSED AND PROPERLY LATCHED WHEN DRIVING. EXTERIOR VIEW OF RIGHT SIDE DOOR Fig LUBRICATION Once the doors are properly adjusted, lubrication (preferably grease) can be applied to the striker bolts and latch assemblies. Reapply periodically as needed (same goes for the door hinges as necessary). Fig. 6

10 Rev. R, p. 10 of 16 KUBOTA RTV 900 V4211, V4212A, V4213, V4262, V4275 Door Hinge Kit Kubota p/n (ref.: code no.: 9PH008X) PIN HINGES HINGE PLATES TUBE SPACERS 1/4-20 x 7/8 LONG HEX HEAD BOLTS HINGE SLEEVES 1/4 USS FLAT WASHERS 1/4-20 x 1 1/2 LONG HEX HEAD BOLTS 1/4-20 LOCK NUTS CONTENTS OF ONE HINGE KIT: (2 hinge kits required per cab) 8-1/4-20 x 1 1/2 long hex head bolts (for Hard Sided doors and Rear Panel hinges) 4-1/4-20 x 7/8 long hex head bolts (for all doors except Hard Sided doors) 8-1/4-20 locknuts 4-1/4 USS flat washers (for rear panel tube only) 2 - hinge sleeves (for doors) 1 - pin hinge (left hand) (for rear tubing) 1 - pin hinge (right hand) (for rear tubing) 2 - hinge plates (for hard sided door tube only) 4 - tube spacers One kit equals one door. Two kits required per cab.

11 Rev. R p. 11 of GAS DOOR SPRINGS 9.1 Install the gas spring to the door receiver and door with the small piston end towards the door (see Fig. 9.1). Press the button on the compression fastener to lock the gas spring to the ball studs. small piston end Fig. 9.1 CARE AND MAINTENANCE Check and tighten hardware after 40 hours of operation. Periodically inspect and tighten hardware for the remainder of the unit s life. Wash the painted surfaces of the unit with commercial automotive cleaning products. Clean windows with glass cleaner.

12

13

14

15

16

INSTALLATION & OWNER S MANUAL

INSTALLATION & OWNER S MANUAL Rev. L p. 1 of 16 INSTALLATION & OWNER S MANUAL V4262 CAMO (SOFT SIDED) CAB KIT INSTALLATION & OWNER S MANUAL The contents of this envelope are the property of the owner. Be sure to leave with the owner

More information

INSTALLATION & OWNER S MANUAL

INSTALLATION & OWNER S MANUAL Rev. E p. of 3 INSTALLATION & OWNER S MANUAL V446 Front Cab Kit and V446 Rear Cab Kit for RTV 40 INSTALLATION & OWNER S MANUAL The contents of this envelope are the property of the owner. Be sure to leave

More information

INSTALLATION & OWNER S MANUAL

INSTALLATION & OWNER S MANUAL INSTALLATION & OWNER S MANUAL CAB INSTALLATION INSTRUCTIONS FOR E-Z-GO MPT BALL CAGE (p/n 72685-G01) The contents of this envelope are the property of the owner. Be sure to leave with the owner when installation

More information

INSTALLATION & OWNER S MANUAL

INSTALLATION & OWNER S MANUAL INSTALLATION & OWNER S MANUAL This Curtis Cab is designed and manufactured for use only as reasonable weather protection. This cab is not applicable, Nor should the cab be considered as protection against

More information

INSTALLATION & OWNER S MANUAL

INSTALLATION & OWNER S MANUAL INSTALLATION & OWNER S MANUAL CAB INSTALLATION INSTRUCTIONS JOHN DEERE 4000 SERIES (4500/4600/4700) (4510/4610/4710) (4120/4320/4520/4720) HARD SIDED CAB ENCLOSURE (p/n 1JD4120AS) SOFT SIDED CAB ENCLOSURE

More information

INSTALLATION & OWNER S MANUAL

INSTALLATION & OWNER S MANUAL Rev. A, p. of 0 INSTALLATION & OWNER S MANUAL MASSEY FERGUSON GC2400 cab kit p/n MFGC2400 Installation Instructions The contents of this envelope are the property of the owner. Be sure to leave with the

More information

INSTALLATION & OWNER S MANUAL

INSTALLATION & OWNER S MANUAL Rev. B, p. 1 of 25 INSTALLATION & OWNER S MANUAL POLARIS RANGER RCS (for models XP or HD) (for model years 2009-) cab without doors kit (p/n 1POLRCWD) cab with doors kit (p/n 1POLRC) doors only kit (p/n

More information

INSTALLATION & OWNER S MANUAL

INSTALLATION & OWNER S MANUAL INDUSTRIES, LLC. INSTALLATION & OWNER S MANUAL CAB INSTALLATION INSTRUCTIONS KUBOTA GRAND L 40 SERIES HARD SIDED CAB ENCLOSURE (p/n 1KGL4AS) This Curtis Cab is designed and manufactured for use only as

More information

INSTALLATION & OWNER S MANUAL

INSTALLATION & OWNER S MANUAL INSTALLATION & OWNER S MANUAL CAB INSTALLATION INSTRUCTIONS MASSEY FERGUSON THX FOR MASSEY FERGUSON 528, 53, AGCO ST28A, ST33A, CHALLENGER MT255B SOFT SIDED CAB ENCLOSURE (p/n MFTHXSS) This Curtis Cab

More information

INSTALLATION & OWNER S MANUAL

INSTALLATION & OWNER S MANUAL Rev. C, p. of 2 INSTALLATION & OWNER S MANUAL KUBOTA B2650/3350 Hard Sided Cab p/n KB33AS Soft Sided Cab p/n KB33SS Installation Instructions The contents of this envelope are the property of the owner.

More information

INSTALLATION & OWNER S MANUAL

INSTALLATION & OWNER S MANUAL INSTALLATION & OWNER S MANUAL CAB INSTALLATION INSTRUCTIONS JOHN DEERE GATOR HPX and/or XUV HARD SIDED CAB ENCLOSURE (p/n: 1GTR44AS) SOFT SIDED CAB ENCLOSURE (p/n: 1GTR44SS) 111 HIGGINS STREET, WORCESTER,

More information

INSTALLATION & OWNER S MANUAL

INSTALLATION & OWNER S MANUAL Rev. D, p. 1 of 14 INSTALLATION & OWNER S MANUAL Bobcat CT 230 and KIOTI CK30 cab kit with hard doors and soft rear curtain p/n 1BCT230 & 1KTCK30 The contents of this envelope are the property of the owner.

More information

INSTALLATION & OWNER S MANUAL

INSTALLATION & OWNER S MANUAL Rev. A, p. 1 of 6 INSTALLATION & OWNER S MANUAL YANMAR SA-424 WINDSHIELD KIT P/N 1CYSA4WS FITS SA-424 TRACTORS WITH 4 POST ROPS The contents of this envelope are the property of the owner. Be sure to leave

More information

INSTALLATION & OWNER S MANUAL

INSTALLATION & OWNER S MANUAL INSTALLATION & OWNER S MANUAL CAB INSTALLATION INSTRUCTIONS FOR MASSEY FERGUSON 233, 428v (gear), 428v (hydro) SOFT SIDED CAB ENCLOSURE (p/n: MF233SS) This Curtis Cab is designed and manufactured for use

More information

INSTALLATION & OWNER S MANUAL

INSTALLATION & OWNER S MANUAL p. 1 of 15 INSTALLATION & OWNER S MANUAL YANMAR Sc2450 cab kit with hard doors and soft rear curtain Curtis p/n: 1CYSC2450AS The contents of this envelope are the property of the owner. Be sure to leave

More information

INSTALLATION & OWNER S MANUAL

INSTALLATION & OWNER S MANUAL Rev. G, p. 1 of 19 INSTALLATION & OWNER S MANUAL YANMAR Sc SERIES cab kit with hard doors and soft rear curtain Curtis p/n: 1CYSC1AS Yanmar p/n: 59A40056727 Optional Hard Rear Panel Curtis p/n: SC100-06A

More information

INSTALLATION & OWNER S MANUAL

INSTALLATION & OWNER S MANUAL INSTALLATION & OWNER S MANUAL CAB INSTALLATION INSTRUCTIONS JOHN DEERE 3000 SERIES (4200/4300/4400) (4210/4310/4410) & (3120/3320/3520/3720) HARD SIDED CAB ENCLOSURE (p/n 1JD3520AS) SOFT SIDED CAB ENCLOSURE

More information

INSTALLATION & OWNER S MANUAL

INSTALLATION & OWNER S MANUAL INSTALLATION & OWNER S MANUAL CAB INSTALLATION INSTRUCTIONS KUBOTA GRAND L 30 SERIES HARD SIDED CAB ENCLOSURE (p/n 1KU3AS) SOFT SIDED CAB ENCLOSURE (p/n 1KU3SS) This Curtis Cab is designed and manufactured

More information

INSTALLATION & OWNER S MANUAL

INSTALLATION & OWNER S MANUAL Rev. C p. 1 of 21 INSTALLATION & OWNER S MANUAL F5205 HARD SIDED CAB KIT INSTALLATION & OWNER S MANUAL The contents of this envelope are the property of the owner. Be sure to leave with the owner when

More information

INSTALLATION & OWNER S MANUAL

INSTALLATION & OWNER S MANUAL Pg. 1 of 14 INSTALLATION & OWNER S MANUAL John Deere Gator XUV 825i S4 Cab (p/n: 1GTRXUV4 Steel Cab with Doors) The contents of this envelope are the property of the owner. Be sure to leave with the owner

More information

INSTALLATION & OWNER S MANUAL

INSTALLATION & OWNER S MANUAL p. 1 of 13 INSTALLATION & OWNER S MANUAL Polaris Ranger 400-EV PathPro SS Cab (fits 2010 - current) (p/n: 1PRG400FS) The contents of this envelope are the property of the owner. Be sure to leave with the

More information

INSTALLATION & OWNER S MANUAL

INSTALLATION & OWNER S MANUAL INSTALLATION & OWNER S MANUAL INSTALLATION INSTRUCTIONS KAWASAKI MULE 4000 CAB KIT (p/n: KAF40-005WA and KAF40-005BA) NOTE: Hard sided doors are sold separately. This manual is the property of the owner.

More information

INSTALLATION & OWNER S MANUAL

INSTALLATION & OWNER S MANUAL p. 1 of 15 INSTALLATION & OWNER S MANUAL Polaris Ranger 500-800 PathPro SS Cab (fits 2010 - current) (p/n: 1POLRFS1) The contents of this envelope are the property of the owner. Be sure to leave with the

More information

INSTALLATION & OWNER S MANUAL

INSTALLATION & OWNER S MANUAL INSTALLATION & OWNER S MANUAL CAB INSTALLATION INSTRUCTIONS JOHN DEERE 4000 SERIES (4500/4600/4700) (4510/4610/4710) (4120/4320/4520/4720) HARD SIDED CAB ENCLOSURE (p/n 1JD4120AS) SOFT SIDED CAB ENCLOSURE

More information

INSTALLATION & OWNER S MANUAL

INSTALLATION & OWNER S MANUAL INSTALLATION & OWNER S MANUAL CAB INSTALLATION INSTRUCTIONS MASSEY FERGUSON TGX SERIES SOFT SIDED CAB ENCLOSURE (p/n MFTGXSS) This Curtis Cab is designed and manufactured for use only as reasonable weather

More information

INSTALLATION & OWNER S MANUAL

INSTALLATION & OWNER S MANUAL INSTALLATION & OWNER S MANUAL INSTALLATION INSTRUCTIONS KAWASAKI MULE 4000 TRANS 4 FRONT CAB KIT (p/n: KAF40T-001WA and p/n: KAF40T-001BA) NOTE: Hard sided doors, soft sided doors, and rear cab are sold

More information

KUBOTA BX-1500/1800/2200 HARD SIDED CAB (p/n 1KBXAS) SOFT SIDED CAB (p/n 1KBXSS)

KUBOTA BX-1500/1800/2200 HARD SIDED CAB (p/n 1KBXAS) SOFT SIDED CAB (p/n 1KBXSS) TRACTOR CAB INC. 111 HIGGINS STREET, WORCESTER, MA 01606 KUBOTA BX-1500/1800/2200 HARD SIDED CAB (p/n 1KBXAS) SOFT SIDED CAB (p/n 1KBXSS) INSTALLATION AND OWNER S MANUAL The contents of this envelope are

More information

INSTALLATION & OWNER S MANUAL

INSTALLATION & OWNER S MANUAL Rev. B, p. 1 of 18 INSTALLATION & OWNER S MANUAL KAWASAKI TERYX ClearView Cab p/n: 1KAWT8002CV This cab fits model years: 2014- The contents of this envelope are the property of the owner. Be sure to leave

More information

INSTALLATION & OWNER S MANUAL

INSTALLATION & OWNER S MANUAL Rev. L, p. 1 of 18 INSTALLATION & OWNER S MANUAL KUBOTA L3200, L3800, and L2501 WorkPro Hard Sided Cab (p/n: 1KL38AS) WorkPro Soft Sided Cab (p/n: 1KL38SS) An optional Hard Rear Panel can be purchased

More information

INSTALLATION & OWNER S MANUAL

INSTALLATION & OWNER S MANUAL Rev. C, p. 1 of 24 INSTALLATION & OWNER S MANUAL HONDA PIONEER 700-4 ClearView Cab p/n: 1HONP7004CV fits model years up thru 2017 The contents of this envelope are the property of the owner. Be sure to

More information

INSTALLATION & OWNER S MANUAL

INSTALLATION & OWNER S MANUAL Rev. D, p. 1 of 29 INSTALLATION & OWNER S MANUAL YAMAHA VIKING YXM 700 ClearView Cab p/n: 1YAMVKCV fits model years up thru 2018 (fits Yanmar Bull model years up thru 2018) The contents of this envelope

More information

INSTALLATION & OWNER S MANUAL

INSTALLATION & OWNER S MANUAL Rev. C, p. 1 of 24 INSTALLATION & OWNER S MANUAL HONDA PIONEER 700-2 ClearView Cab p/n: 1HONP7002CV This cab fits model years up thru 2016. The contents of this envelope are the property of the owner.

More information

INSTALLATION & OWNER S MANUAL

INSTALLATION & OWNER S MANUAL p. 1 of 15 INSTALLATION & OWNER S MANUAL John Deere Gator PathPro SS Cab (fits all HPX and XUV models with the O.P.S. system installed) (p/n: 1GTRXUV) (O.P.S. = Operator Protective Structure) The contents

More information

INSTALLATION & OWNER S MANUAL

INSTALLATION & OWNER S MANUAL Rev. C, p. 1 of 18 INSTALLATION & OWNER S MANUAL KUBOTA RTV 400 CAB (Not for use on RTV 500) These instructions are for installation of the complete cab as well as the modular components. DESCRIPTION:

More information

Assembly Instructions

Assembly Instructions Assembly Instructions Part Number Description Model Approx. Assembly Time 99994-049 Cab Enclosure MULE SX 3-4 Hours WARNING Improper installation of this accessory could result in an accident causing serious

More information

INSTALLATION & OWNER S MANUAL

INSTALLATION & OWNER S MANUAL p. 1 of 13 INSTLLTION & OWNER S MNUL Kubota X 70 Series Cab (fits X2370, X2670, and X25D) (p/n: 1KX70S Steel Cab) (p/n: 1KX70SS Vinyl Cab) The contents of this envelope are the property of the owner. e

More information

INSTALLATION & OWNER S MANUAL

INSTALLATION & OWNER S MANUAL Rev. K, p. 1 of 19 INSTALLATION & OWNER S MANUAL V4210 CAB KIT (color: orange) and/or V4220 CAB KIT (color: camo) INSTALLATION & OWNER S MANUAL The contents of this envelope are the property of the owner.

More information

INSTALLATION & OWNER S MANUAL

INSTALLATION & OWNER S MANUAL Page 1 of 16 INSTALLATION & OWNER S MANUAL YAMAHA VIKING CAB KIT WITH HARD DOORS p/n: 1YAMVK fits model years 2014- (fits Yanmar Bull model years 2017-) NOTE: By design, the doors are made to not be removable!

More information

INSTALLATION & OWNER S MANUAL

INSTALLATION & OWNER S MANUAL Rev. K, p. 1 of 11 INSTALLATION & OWNER S MANUAL POLARIS FREEDOM CAB INSTALLATION INSTRUCTIONS FOR THE POLARIS RANGER (p/n 2876196-067) IMPORTANT: THIS ACCESSORY WEIGHS 340 POUNDS. PLEASE ADJUST THE VEHICLE

More information

INSTALLATION & OWNER S MANUAL

INSTALLATION & OWNER S MANUAL 1 of 12 INSTALLATION & OWNER S MANUAL KAWASAKI MULE Pro FX-FXT CORNER FLASHER KIT p/n: 1KAPFXCFL Required Accessories: Fuse Panel: Kawasaki P/N: KAF080-076 Or Curtis P/N: 1KAPFXFP Approximate Installation

More information

INSTALLATION & OWNER S MANUAL

INSTALLATION & OWNER S MANUAL Page 1 of 18 INSTALLATION & OWNER S MANUAL John Deere 3 Family Premium Cab p/n: 1JD3FPR Standard Cab p/n: 1JD3FST Fits Tractor Models: 3033R, 3039R, 3046R Premium Cab Shown with Optional Front LED Work

More information

INSTALLATION & OWNER S MANUAL

INSTALLATION & OWNER S MANUAL INSTALLATION & OWNER S MANUAL V5008 Kubota RTV 72 Snow Blade The contents of this envelope are the property of the owner. Be sure to leave with the owner when installation is complete. IMPORTANT: Please

More information

INSTALLATION & OWNER S MANUAL

INSTALLATION & OWNER S MANUAL 1 of 22 INSTALLATION & OWNER S MANUAL Kawasaki Mule PRO-FXT p/n s: 1KAPFXTCA & 1KAPFXTCAS1 fits all Mule Pro 6-Passenger Models Cab Shown with Optional Front Wiper, Lights, and Side View Mirrors Available

More information

DOOR KIT P/N , APPLICATION BEFORE YOU BEGIN KIT CONTENTS. Verify accessory fitment at Polaris.com.

DOOR KIT P/N , APPLICATION BEFORE YOU BEGIN KIT CONTENTS. Verify accessory fitment at Polaris.com. DOOR KIT P/N 2882561, 2882562 APPLICATION Verify accessory fitment at Polaris.com. BEFORE YOU BEGIN Read these instructions and check to be sure all parts and tools are accounted for. Please retain these

More information

INSTALLATION & OWNER S MANUAL

INSTALLATION & OWNER S MANUAL Page 1 of 20 INSTALLATION & OWNER S MANUAL Massey Ferguson GC1700 Series All Steel Cab p/n: 1MFGC1700AS1 Soft Side Cab p/n: 1MFGC1700SS1 Fits Tractor Models: GC1705, GC1710, GC1715, GC1720 All Steel Cab

More information

INSTALLATION & OWNER S MANUAL

INSTALLATION & OWNER S MANUAL P. 1 of 14 INSTALLATION & OWNER S MANUAL CAB INSTALLATION BEFORE YOU START HELPFUL REMINDERS: KUBOTA F-SERIES CAB p/n: F5206 The contents of this envelope are the property of the owner. Be sure to leave

More information

Ref Qty Part Description Part Number -1- Kit ( ) Contents:

Ref Qty Part Description Part Number -1- Kit ( ) Contents: REAR CANVAS DOOR KIT 900 XP RANGER CREW P/N 2879899 Application RANGER 900 XP CREW Before you begin, read these instructions twice and check to be sure all parts and tools are accounted for. Please retain

More information

P/N Rev 01 04/14-1- NOTE: If you are ordering hinges for your rear doors, order and/or

P/N Rev 01 04/14-1- NOTE: If you are ordering hinges for your rear doors, order and/or REAR CANVAS DOOR KIT 900 XP RANGER CREW P/N 2879899 Application RANGER 900 XP CREW Before you begin, read these instructions twice and check to be sure all parts and tools are accounted for. Please retain

More information

Assembly Instructions

Assembly Instructions Assembly Instructions Part Number Description Model Approx. Assembly Time 99994-0903 Windshield Wiper Kit Mule SX 1 Hour WARNING Improper installation of this accessory could result in an accident causing

More information

SCION tc STRUT TIE BAR Preparation

SCION tc STRUT TIE BAR Preparation SCION tc 2005 - STRUT TIE BAR Preparation Part Number: 00016-80440 Code: YY1 Kit Contents 1 1 DS Mount Plate 2 1 PS Mount Plate 3 1 Cross Bar 4 1 Hardware Bag Hardware Bag Contents 1 4 8mm Screws 2 4 8mm

More information

INSTALLATION & OWNER S MANUAL

INSTALLATION & OWNER S MANUAL Page 1 of 20 INSTALLATION & OWNER S MANUAL John Deere 4 Family Premium Cab p/n: 1JD4FPR Fits Tractor Models: 4044R, 4052R, 4066R Premium Cab Shown with Optional Front Work Lights. Available Options: 1.

More information

Assist Step Kit Installation (Side Assist Step)

Assist Step Kit Installation (Side Assist Step) Page 1 of 6 2015 Chevrolet Silverado - 2WD Cheyenne, Sierra, Silverado Accessory Installation Manual Accessories Exterior Trim Accessories Accessories Document ID: 2741491 Assist Step Kit Installation

More information

SERVICE & OWNER S MANUAL

SERVICE & OWNER S MANUAL 1 of 10 SERVICE & OWNER S MANUAL Product Specifications 25 x 36 x 7 Weight: 47 lbs. Air Flow: 260 CFM Air Conditioner p/n: 1ACUNIT-G1 Fits with Curtis Roof Kit: Contact Curtis for Details. Fits with Curtis

More information

INSTALLATION & OWNER S MANUAL

INSTALLATION & OWNER S MANUAL Page 1 of 30 INSTALLATION & OWNER S MANUAL John Deere 1 Family Premium Cab p/n: 1JD1FPR Standard Cab p/n: 1JD1FST Fits Tractor Models: 1023E and 1025R Premium Cab Shown with Optional Front LED Work Lights.

More information

SPECIAL INSTALLATION INSTRUCTIONS

SPECIAL INSTALLATION INSTRUCTIONS SPECIAL INSTALLATION INSTRUCTIONS WARN 4X FLARES FRONT AND REAR '98 TOYOTA HILUX DUAL-CAB As you read these instructions, you will see NOTES, CAUTIONS and WARNINGS. Each message has a specific purpose.

More information

CANVAS DOOR KIT P/N , APPLICATION BEFORE YOU BEGIN KIT CONTENTS. Verify accessory fitment at Polaris.com.

CANVAS DOOR KIT P/N , APPLICATION BEFORE YOU BEGIN KIT CONTENTS. Verify accessory fitment at Polaris.com. CANVAS DOOR KIT P/N 2882902, 2882903 APPLICATION Verify accessory fitment at Polaris.com. BEFORE YOU BEGIN Read these instructions and check to be sure all parts and tools are accounted for. Please retain

More information

TIP-OUT GLASS WINDSHIELD KIT

TIP-OUT GLASS WINDSHIELD KIT TIP-OUT GLASS WINDSHIELD KIT P/N 2881108 APPLICATION Verify accessory fitment at Polaris.com. BEFORE YOU BEGIN Read these instructions and check to be sure all parts and tools are accounted for. Please

More information

<THESE INSTRUCTIONS MUST BE GIVEN TO THE END USER> B&W

<THESE INSTRUCTIONS MUST BE GIVEN TO THE END USER> B&W B&W Trailer Hitches 6 Hawaii Rd / PO Box 86 Humboldt, KS 66748 P:60.473664 F:60.869.903 Turnoverball Gooseneck Hitch Installation Instructions MODEL 08

More information

POLY TIP-DOWN WINDSHIELD KIT

POLY TIP-DOWN WINDSHIELD KIT POLY TIP-DOWN WINDSHIELD KIT P/N 2883261 APPLICATION Verify accessory fitment at Polaris.com. BEFORE YOU BEGIN Read these instructions and check to be sure all parts and tools are accounted for. Please

More information

Wildcat System Instructions

Wildcat System Instructions Wildcat System Instructions NOTE: Most steps contained in these instructions will need to be repeated on the other side of the vehicle. Prior to assembly of windshield it is necessary to establish what

More information

Installation Guide. Stowe Cargo Management System. Table of Contents

Installation Guide. Stowe Cargo Management System. Table of Contents Installation Guide Stowe Cargo Management System Table of Contents 1. Pre-Installation (Page 2) a. Notes, Installation Kit contents & Tools needed 2. How to Install the Stowe Cargo Management System (Pages

More information

INSTALLATION & OWNER S MANUAL

INSTALLATION & OWNER S MANUAL INSTALLATION & OWNER S MANUAL UTV UNIVERSAL Plow Kit 6 Wide Snow Plow (Self Contained Hyd.) (p/n: 1UTVP = factory assembled) (p/n: 1UTVP-1 = assembly required) For the 1UTVP version, the instructions are

More information

INSTALLATION INSTRUCTIONS

INSTALLATION INSTRUCTIONS NEW HOLLAND MODELS T1530 CNH Original Parts INSTALLATION INSTRUCTIONS #710660156 ALL WEATHER CAB COMPACT TRACTORS 40273809 1 CARTON CONTENTS: ALL WEATHER CAB #710660156 Key# Part# Qty. Description 1 40274

More information

Installation Instructions Capacity 10,000 lbs. (100 Series Lift)

Installation Instructions Capacity 10,000 lbs. (100 Series Lift) Installation Instructions Capacity 10,000 lbs. (100 Series Lift) IMPORTANT Reference ANSI/ALI ALIS, Safety Requirements for Installation and Service of Automotive Lifts before installing lift. OPERATING

More information

INSTALLATION & OWNER S MANUAL

INSTALLATION & OWNER S MANUAL 1 of 21 INSTALLATION & OWNER S MANUAL A/C Drive Kit for KUBOTA BX2670-1 and BX2680 p/n: 1ACBX2680DRK (Note: the alternator is supplied with a new pulley) Must be installed with one of the following three

More information

Stowe Cargo Management System

Stowe Cargo Management System Installation Guide Stowe Cargo Management System Table of Contents 1. Pre-Installation (Page 2) a. Notes, Installation Kit contents & Tools needed 2. How to Install the Stowe Cargo Management System (Pages

More information

WOC Mid Size Door Installation

WOC Mid Size Door Installation WOC-10112 Mid Size Door Installation NOTE: If the Mid Size Ranger that you are installing this door system on is a 2010 or newer you will need to remove the sill plates and side nets. If the doors are

More information

MOUNTING INSTRUCTIONS JOHN DEERE GATOR NON-ROPS CAB

MOUNTING INSTRUCTIONS JOHN DEERE GATOR NON-ROPS CAB MOUNTING INSTRUCTIONS JOHN DEERE GATOR NON-ROPS CAB FITS 4X2 & 6X4 GATORS A-11112, A-11224, A-11225, A-11226 MANUFACTURED BY: BOX 70 LITCHFIELD, MINNESOTA 55355-0070 (320) 693-3221 Fax: (320) 693-7252

More information

POLY TIP-DOWN WINDSHIELD KIT

POLY TIP-DOWN WINDSHIELD KIT POLY TIP-DOWN WINDSHIELD KIT P/N 2881919 APPLICATION Verify accessory fitment at Polaris.com. BEFORE YOU BEGIN Read these instructions and check to be sure all parts and tools are accounted for. Please

More information

Multistrada (MTS) Tank Installation Notes. Tools Required. Phase 1: Remove Fairings. Phase 2: Remove Fuel Tank

Multistrada (MTS) Tank Installation Notes. Tools Required. Phase 1: Remove Fairings. Phase 2: Remove Fuel Tank The California Cycleworks MTS tank provides an aftermarket alternative to the OEM nylon fuel tanks as used on aircooled Desmodue Ducati Multistrada 1100, 1000, and 620 models. This fuel tank is NOT for

More information

Installation Instructions

Installation Instructions Preparing your vehicle to install your brake system upgrade 1. Rack the vehicle. 2. If you don t have a rack, then you must take extra safety precautions. 3. Choose a firmly packed and level ground to

More information

FLOODLIGHT unit IMPORTANT WARNING! RRAC055/RRAC059. INSTALL TIME: 30 mins

FLOODLIGHT unit IMPORTANT WARNING! RRAC055/RRAC059. INSTALL TIME: 30 mins LED 4" FLOODLIGHT unit RRAC055/RRAC059 INSTALL TIME: 30 mins Depending on the type of installation chosen, not all components supplied will be used. Refer to Page 13 Section 7 on how to set the angle of

More information

JOHN DEERE GATOR SWITCH PANEL INSTRUCTIONS FITS 1GTRXUV2 AND 1GTRXUV4 CABS (p/n: 1XUVSP)

JOHN DEERE GATOR SWITCH PANEL INSTRUCTIONS FITS 1GTRXUV2 AND 1GTRXUV4 CABS (p/n: 1XUVSP) P. 1 of 5 JOHN DEERE GATOR SWITCH PANEL INSTRUCTIONS FITS 1GTRXUV2 AND 1GTRXUV4 CABS (p/n: 1XUVSP) Note: Harness Extension Kit Required for 4 Passenger (p/n: 1XUV4WHEK) This manual is the property of the

More information

Bag 1. Bag 1. Center Pivot. Center Pivot

Bag 1. Bag 1. Center Pivot. Center Pivot 8 00734 01901 5 Center Pivot Bag 1 3374 - Center Pivot Socket 4019 - Alum Pivot ball 3254-2-56 Button Head *Note - Sometimes it is helpful to slightly over-tighten the top clamp screws, then work the ball

More information

RMK HANDLEBAR KIT P/N ; ; APPLICATION BEFORE YOU BEGIN KIT CONTENTS. Verify accessory fitment at Polaris.com.

RMK HANDLEBAR KIT P/N ; ; APPLICATION BEFORE YOU BEGIN KIT CONTENTS. Verify accessory fitment at Polaris.com. RMK HANDLEBAR KIT P/N 2883835; 2883836; 2883837 APPLICATION Verify accessory fitment at Polaris.com. BEFORE YOU BEGIN Read these instructions and check to be sure all parts and tools are accounted for.

More information

HARD TRI-FOLD COVER SPECIAL BOLT ON SIDE RAIL INSTRUCTIONS 2016-ON TOYOTA TACOMA 6 BOX

HARD TRI-FOLD COVER SPECIAL BOLT ON SIDE RAIL INSTRUCTIONS 2016-ON TOYOTA TACOMA 6 BOX HARD TRI-FOLD COVER SPECIAL BOLT ON SIDE RAIL INSTRUCTIONS 2016-ON TOYOTA TACOMA 6 BOX Read and follow these special instructions along with the standard instructions carefully before installing or using

More information

RH INSTALL INSTRUCTIONS

RH INSTALL INSTRUCTIONS Tips for Installing Rhinogear Products The recommended sequence for installing our Rhinogear line of products on your Rhino. This sequence will help with ease of installation and help save time by eliminating

More information

70 Series 8700 End Mount Three Phase Brake Instructions IP56 (NEMA 4) Housing

70 Series 8700 End Mount Three Phase Brake Instructions IP56 (NEMA 4) Housing Bulletin No. BK4773-3 (08/2016) 70 Series 8700 End Mount Three Phase Brake Instructions IP56 (NEMA 4) Housing Read carefully before attempting to assemble, install, operate or maintain the product described.

More information

2008~2010 Polaris RZR 800* Cab Enclosure Kit Slam latch hardware

2008~2010 Polaris RZR 800* Cab Enclosure Kit Slam latch hardware Owner s Manual Model: Polaris RZR * 2008~2010 Polaris RZR 800* Cab Enclosure Kit Slam latch hardware Caution: Before using this product, read this manual and follow all safety instructions. Safety Instructions

More information

Factory Five Racing, Inc. 818 Kit Assembly manual revision 1J update

Factory Five Racing, Inc. 818 Kit Assembly manual revision 1J update Factory Five Racing, Inc. 818 Kit Assembly manual revision 1J update Turbo coolant overflow tank...1 Shifter handle...4 Install...4 Door skin...7 Door Liner... 10 Side mirrors... 14 Door handles and pulls...

More information

INSTALLATION INSTRUCTIONS

INSTALLATION INSTRUCTIONS INSTALLATION INSTRUCTIONS 6525 REAR AXLE FLIP & HANGER KIT 5 OR 6 INCH LOWERING 14&UP CHEVROLET SILVERADO / GMC SIERRA 1500 Thank you for being selective enough to choose our high quality BELLTECH PRODUCT.

More information

INSTALLATION INSTRUCTIONS

INSTALLATION INSTRUCTIONS NEW HOLLAND MODELS TC21DA TC24DA TC23DA TC26DA CASE MODELS DX21 DX24 DX23 DX26 CNH Original Parts INSTALLATION INSTRUCTIONS #710660106 ALL WEATHER CAB COMPACT TRACTORS 113901203 1 CARTON CONTENTS: ALL

More information

Cab Kit Installation Instructions

Cab Kit Installation Instructions Low Speed Vehicles (LSV) Electric Vehicles: Carryall Carryall 6 Cab Kit Installation Instructions Publication 050770 These instructions apply to the following kit: 0670 Edition Code 008E09D GENERAL INFORMATION

More information

HARD TRI-FOLD COVER SPECIAL BOLT ON SIDE RAIL INSTRUCTIONS 2016-ON TOYOTA TACOMA 5 BOX

HARD TRI-FOLD COVER SPECIAL BOLT ON SIDE RAIL INSTRUCTIONS 2016-ON TOYOTA TACOMA 5 BOX HARD TRI-FOLD COVER SPECIAL BOLT ON SIDE RAIL INSTRUCTIONS 2016-ON TOYOTA TACOMA 5 BOX Read and follow these special instructions along with the standard instructions carefully before installing or using

More information

Place these instructions in vehicle s glove box after installation is complete. Clean Tonneau Cover with a mild detergent and water solution.

Place these instructions in vehicle s glove box after installation is complete. Clean Tonneau Cover with a mild detergent and water solution. Place these instructions in vehicle s glove box after installation is complete Installation Time: Approx. 60 Minutes Care Instructions: Clean Tonneau Cover with a mild detergent and water solution. Do

More information

AL625 & AL625HD INSTALLATION & OWNER S MANUAL

AL625 & AL625HD INSTALLATION & OWNER S MANUAL AL625 & AL625HD INSTALLATION & OWNER S MANUAL These instructions are provided to assist you in the installation of the AL625. If you require further assistance, our trained staff is ready to provide you

More information

ATLAS TRANSFER CASES CABLE SHIFTER units built after 5/1/12

ATLAS TRANSFER CASES CABLE SHIFTER units built after 5/1/12 KIT CONSISTS OF: No. Qty Part No. Description P.O. Box 247, 4320 Aerotech Center Way PAGE 1 OF 6 Page Rev. Date: 08-01-17 1 1 302051 BASE- TWIN STICK MOUNT 2 1 302060 BOOT- TWIN STICK 3 1 302063 BOOT RING-

More information

Instructions for 2-row monitoring only

Instructions for 2-row monitoring only Installation Instructions for CaseIH cotton picker models: Instructions for 2-row monitoring only Ensure the model numbers shown above correspond to the machine model. If you receive the incorrect installation

More information

GPS Steering System Installation Manual

GPS Steering System Installation Manual GPS Steering System Installation Manual Supported Vehicles Challenger Massey Ferguson AGCO MT-645C, MT-645D MF-8650 DT-205B MT-655C, MT-655D MF-8660 DT-225B MT-665C, MT-665D MF-8670 DT-250B MT-675C, MT-675D

More information

Page 1 of 12 DZ /15/13

Page 1 of 12 DZ /15/13 Page 1 of 12 Dee Zee Ford Super Duty luminum Flow Through Tailgate Installation Instructions Congratulations on your purchase of a quality Dee Zee product. Dee Zee is recognized as having the highest quality

More information

GPS AutoSteer System Installation Manual

GPS AutoSteer System Installation Manual GPS AutoSteer System Installation Manual Supported Vehicles Agco Gleaner Combines R65 R66 R75 R76 PN: 602-0288-01-A LEGAL DISCLAIMER Note: Read and follow ALL instructions in this manual carefully before

More information

INSTALLATION INSTRUCTIONS

INSTALLATION INSTRUCTIONS INSTALLATION INSTRUCTIONS Accessory HARD FRONT DOORS P/N 0SU95-HL4-104 Application SXS1000M3/M3P/M3L/M5D/ M5P/M5L Honda Dealer: Please give a copy of these instructions to your customer. Publication No.

More information

Installation Manual. AutoSteer. Gleaner Combine. AutoGuide 2 Steer Ready. Supported Models A66 A76 R66 R76 S67 S77 PN: A

Installation Manual. AutoSteer. Gleaner Combine. AutoGuide 2 Steer Ready. Supported Models A66 A76 R66 R76 S67 S77 PN: A Installation Manual AutoSteer Gleaner Combine AutoGuide 2 Steer Ready Supported Models A66 A76 R66 R76 S67 S77 PN: 602-0312-01-A LEGAL DISCLAIMER Note: Read and follow ALL Instructions in this manual carefully

More information

INSTALLATION INSTRUCTIONS

INSTALLATION INSTRUCTIONS INSTALLATION INSTRUCTIONS --1075 North Ave. Sanger, CA 93657-3539 local: 559-875-0222 fax: 559-876-2259 toll free: 800-445-3767-- 2000 1984 1991 Toyota 2 Wheel Drive Pick-Ups 2 Front Dropped Spindles Congratulations!

More information

SCION xa 2004 SATELLITE RADIO TUNER Section I Installation Preparation

SCION xa 2004 SATELLITE RADIO TUNER Section I Installation Preparation Section I Installation Preparation Part Number: PT546 52040 Section I Installation Preparation Kit Contents Item # Quantity Reqd. Description 1 1 Satellite Tuner 2 1 Ground Cable 3 1 Tuner Cable 4 2 Tuner

More information

INSTALLATION INSTRUCTIONS

INSTALLATION INSTRUCTIONS INSTALLATION INSTRUCTIONS REAR DISC CONVERSION KIT A126-2 1988-98 C1500 2WD 10" REAR DRUM Thank you for choosing STAINLESS STEEL BRAKES CORPORATION for your braking needs. Pleases take the time to read

More information

INSTALLATION & OWNER S MANUAL

INSTALLATION & OWNER S MANUAL Rev. A, p. 1 of 13 INSTALLATION & OWNER S MANUAL Polaris Ranger (2009-) Straight UTV Steel Plow with Vehicle Mount Kit 6 Wide Snow Plow (p/n: 1POLSP) (fits the 500 H.O., 700 & 800 HD & XP) The contents

More information

IMPORTANT WARRANTY & INSTALLATION INSTRUCTIONS ATTACHED

IMPORTANT WARRANTY & INSTALLATION INSTRUCTIONS ATTACHED IMPORTANT WARRANTY & INSTALLATION INSTRUCTIONS ATTACHED Please Forward All Attached Information to Consumer Warranty Not Valid Unless Returned to CORSA Performance We ask that you take a few moments to

More information

INSTALLATION INSTRUCTIONS

INSTALLATION INSTRUCTIONS INSTALLATION INSTRUCTIONS --1075 North Ave. Sanger, CA 93657-3539 local: 559-875-0222 fax: 559-876-2259 toll free: 800-445-3767-- 6522 REAR AXLE FLIP & SHACKLE KIT 07-UP CHEVROLET 1500 REGULAR CAB ONLY

More information

RIM Hood For Aeromaster Bodies

RIM Hood For Aeromaster Bodies RIM Hood For Aeromaster Bodies Service Guide WARNING: Hood should be opened by releasing the hold-down straps, lifting the hood, and engaging the prop rod. Be sure prop rod is properly engaged before working

More information