Big & Tall Chair Assembly Instructions

Transcription

1 Designed to be comfortable, and built to stay that way. Big & Tall Chair Assembly Instructions Model A / B 400 lbs

2 PARTS D1 A B D2 D C Casters Star Base E Arms Seat Cushion I J K L 1 Screws 2-1/4 Screws 1-1/4 Screws 2-3/4 Screws with Spring Washers Quantity: 5 Quantity: 2 Quantity: 2 M Plastic Caps Quantity: 4 Gas Lift with Telescoping Cover Quantity:1 Quantity: 1 Quantity: 2 Back Cushion Plastic Shroud Quantity: 1 Quantity: 4 Quantity: 1 H G Quantity:1 Seat Plate Quantity: 1 Quantity: 4 N Allen Key Quantity: 1 WARNINGS 1. This product should be used by only one person at a time. 2. Do not use this chair unless all bolts, screws and knobs are securely tightened. 3. Save the hexagonal wrench. Check that all bolts, screws and knobs are tight every three months or as needed. 4. Dispose of packing material properly. Do not use the plastic cover as a head covering. It may cause suffocation. 5. Do not use the chair as a stepladder. 6. To clean the product, use only a clean cloth. The use of chemicals or cleaning products may affect the color fastness. 7. Use this chair for its intended purpose only. 8. The casters sold with this chair are intended for use on carpet. They are not recommended for use on tile or hard-wood floors. Using these casters on tile or wood flooring may cause damage to the floor surface. Please consider using a chair mat to protect your floor surfaces. 2

3 Step 1 Place the star base (B) upside down and insert 5 casters (A) into the holes on the star base (B). A B Step 2 Turn the star base (B) over and insert the gas lift with telescoping cover (C) through the center hole on top of star base (B). C B 3

4 N Step 3 Attach seat plate (D) to the bottom of the seat cushion () (with the front of the seat plate facing the front of seat cushion). Attach by using two 2-1/4 screws (J) for the front holes of the seat plate (D) and two 1 screws (I) for the rear holes of the seat plate (D) and tighten the screws using allen key (N). *Note: Put all (4) screws through seat plate into the holes before tightening. J I Plastic Spacer D D1 Step 4 Insert levers (D1 & D2) of seat plate (D) to the pre-attached cable lever receivers on the underside of seat cushion () (with the front of levers facing the front of seat cushion). Push down the key on the receivers to pull out the levers. *Note: ix the cable for the seat plate into the plastic clips attached to the bottom of the seat cushion. D2 D Insert Assemble the lever 4 Push Disassemble the lever

5 Step 5 Position the back support plate over the seat plate (D), and attach the back cushion(g) to the seat cushion () with four 1-1/4" screws (K). *Note: Do NOT tighten the screws completely. D G K N E E Step 6 Insert four 2-3/4" screws with spring washers (L) into arm holes attaching arms (E) (with front of arms facing the front of seat cushion) to sides of seat cushion () and back cushion (G). *Note: Tighten all the screws completely. L L G N 5

6 Step 7 Put the plastic shroud (H) over the seat plate (D) (with front of plastic shroud facing the front of seat cushion). Align shroud posts to holes on bottom of seat cushion () and press into position. H D Step 8 Position the assembled chair upright with the seat plate facing down. Insert the gas lift with telescoping cover (C) into the center hole of the seat plate (D). C 6 D

7 Step 9 Press the plastic caps (M) into the holes on outside of the arms once all screws have been tightened. M M Step 10 Remove the packing material (P) placed between the back cushion and the air frame. The chair is now ready for use. P 7

8 Operating Instructions unction Instruction - 1 To Adjust Seat Height: While seated, lean forward and reach under the right side of the chair to find the lever. Lift the lever and raise your body up slightly to allow the chair to rise to the desired height. Once desired height is reached, release lever to lock chair at desired height. To lower the seat, lift the lever while seated. The chair will descend until the lever is released or the chair reaches the bottom position. unction Instruction - 2 To Operate Tilt Lockout: While seated, reach under the left side of the chair to find the lever. Push down the lever and lean back to allow the chair to tilt backwards. To lock the chair in the upright or vertical position, sit upright and pull the lever to the up position. 8

9 unction Instruction - 3 To Adjust Tension On The Tilt: Reach under the front center of the chair, grasp the round knob (R) and turn it counter- clockwise to stiffen the tilt mechanism for a heavier user. Turn the knob (R) clockwise to loosen the tilt mechanism for a lighter user. Rotate the knob (R) until the desired resistance is reached. R unction Instruction Swivel: 360 seat swivel. 9

10 unction Instruction - 5 About the breathability of the Air Lumbar Cushion: While seated, the open-air contours of the cushion which is designed to breathe and flex, can dynamically provide continuous support by connecting with your body's natural movement. The air cushion conforms to the curve of your spinal cord and are intended to relieve your back from stress. Note: It is not intended to diagnose, treat, cure or prevent any disease. If pain increases, please discontinue use. 10

11 unction Instruction - 6 About the Neutral Posture of the Air Lumbar Cushion: The AirTM chair has been shown to help the user achieve Neutral Posture. Neutral Posture has been shown to reduce back strain and increase long term seated comfort. *Provides constant support as you lean back and twist. *lexible lumbar pivots and conforms following your movement. *Continuous proper lumbar support helps keep the body in an optimal working position for maximum comfort. 11

12 YEAR Limited Warranty LA-Z-BOY is a trademark of La-Z-Boy Incorporated and is used under license to L Products Pte Ltd.