Operating Instructions. Excellence Comparator Balances XP-K Models Part 1

Transcription

1 Operating Instructions Excellence Comparator Balances XP-K Models Part 1

2

3 Table of Contents 1 Introduction Symbols and presentations used 6 2 Safety Information Definition of signal warnings and symbols Product specific safety notes 7 3 Overview XP-K Comparators 9 4 Installation and Putting into Operation Unpacking and checking the standard equipment Scope of delivery Selecting the location and level of the balance Location Leveling the balance Unblocking and assembling the balance Installing the balance cable in the terminal Placing the terminal Connecting the balance Setting the reading angle Transporting the balance 14 5 Special Settings for Comparators Load the balance Settings for the balances 15 6 Maintenance Cleaning Disposal 16 7 Technical Data General data Explanatory notes for the METTLER TOLEDO AC adapter Model-specific data Dimensions Dimensions XP155KS Dimensions XP604KM, XP1003KM Dimensions XP2003KL, XP6002KL Dimensions Terminal Interfaces Specifications of RS232C 24 8 Accessories and Spare Parts Accessories Spare parts 29 9 Appendix MT-SICS interface commands and functions 30 Index 31 Table of Contents 3

4

5 1 Introduction Thank you for choosing a METTLER TOLEDO balance. In this chapter you will be given basic information about your balance. Please read right through this chapter carefully even if you already have experience with METTLER TOLEDO balances. Please pay special attention to the safety warnings! The different models have different characteristics regarding equipment and performance. Special notes in the text indicate where this makes a difference to operation. The XP line comprises a range of balances which differ from each other in relation to their weighing range and resolution. The following features are common to all models of the XP lines: Fully automatic adjustment "ProFACT" using internal weights. Built-in applications for WeighCom, normal weighing, statistics, formulation, piece counting, percent weighing, density, differential weighing, and LabX Client. Integral RS232C interface. Touch-sensitive graphics terminal ("Touch screen") with color display. Two programmable sensors for hands-off operation ("SmartSens") to speed up frequently recurring tasks. A brief word about standards, guidelines, and methods of quality assurance: The balances comply with usual standards and guidelines. They support standard procedures, specifications, working methods, and reports according to GLP (Good Laboratory Practice). In this connection, records of working procedures and adjustments become very important; for this purpose we recommend you to use a printer from the METTLER TOLEDO range, since these are optimally adapted to your balance. The balances conform to the applicable standards and guidelines and possess a EC declaration of conformity. METTLER TOLEDO is certified as manufacturer according to ISO 9001 and ISO The operating instructions for the XP balances consist of 4 separate documents, whose contents are listed below. Part 1, this document Contents Introduction Safety Information Installation and Putting into Operation (performed by a service technician from METTLER TOLEDO) Special Settings for XP-K Comparators Cleaning and Service Technical Data Accessories Spare Parts Interface Commands and MT-SICS Functions Part 2, separate document Contents: Terminal, System, and Applications Basic Principles for Using the Terminal and the Firmware System Settings User-specific Settings Applications Firmware (Software) Updates Error and Status Messages Introduction 5

6 Conversion Table for Weight Units Recommended Printer Settings Part 3, separate document Contents: Adjustments, and Tests Adjustments Tests Operating Instructions "WeighCom Application for XP Comparator Balances" When working with the [WeighCom] application, use the operating instructions "WeighCom Application for XP Comparator Balances" that were included with the delivery. Finding more information u Firmware version The operating instructions are based on the initially installed terminal firmware (software) version V Symbols and presentations used The following conventions apply to the operating instructions: part 1, part 2, part 3 and WeighCom application for XP comparator balances. Key designations are indicated by a picture or text in double angular parentheses (e.g. or «On/Off»). 1 2 These symbols indicate an instruction: prerequisites steps results 6 Introduction

7 2 Safety Information 2.1 Definition of signal warnings and symbols Safety notes are marked with signal words and warning symbols. These show safety issues and warnings. Ignoring the safety notes may lead to personal injury, damage to the balance, malfunctions and false results. Signal words WARNING CAUTION Attention Note for a hazardous situation with medium risk, possibly resulting in severe injuries or death if not avoided. for a hazardous situation with low risk, resulting in damage to the device or the property or in loss of data or minor or medium injuries if not avoided. (no symbol) for important information about the product. (no symbol) for useful information about the product. Warning symbols General hazard Electrical shock Heavy object Mandatory safety signs Wear gloves 2.2 Product specific safety notes Intended use Your balance is used for weighing. Use the balance exclusively for this purpose. Any other type of use and operation beyond the limits of technical specifications without written consent from Mettler-Toledo AG, is considered as not intended. It is not permitted to use the instrument in explosive atmosphere of gases, steam, fog, dust and flammable dust (hazardous environments). General safety information Your instrument meets the state of the art technology and complies with all recognized safety rules, however, certain hazards may arise in extraneous circumstances. Do not open the housing of the instrument: It does not contain any parts which can be maintained, repaired or replaced by the user. If you ever have problems with your instrument, contact your authorized METTLER TOLEDO dealer or service representative. Always operate and use your balance only in accordance with the operating instructions part 1, part 2, part 3 and WeighCom application for XP comparator balances. The instructions for setting up your new balance must be strictly observed. Safety Information 7

8 If the instrument is not used according to the manufacturer s operating instructions (part 1, part 2, part 3 and WeighCom application for XP comparator balances), protection of the instrument may be impaired. Staff safety In order to use the instrument, you must have read and understood the operating instructions. Keep the operating instructions for further reference. Never make any modifications to the instrument and use only original spare parts and optional equipment from METTLER TOLEDO. Safety notes WARNING Risk of electric shock Use only the original universal AC adapter delivered with your balance, and check that the voltage printed on it is the same as your local power supply voltage. Only plug the adapter into a socket which is grounded. WARNING Heavy object Single person lift could cause injury. Do not move or lift this equipment without assistance. For moving this equipment ask your METTLER TOLEDO representative. CAUTION Damage of device For use only in dry interior rooms. Do not use sharply pointed objects to operate the keyboard! Although your balance is very ruggedly constructed, it is nevertheless a precision instrument. Treat it with corresponding care. Do not open the balance: It does not contain any parts which can be maintained, repaired, or replaced by the user. If you ever have problems with your balance, contact your METTLER TOLEDO dealer. Use only balance accessories and peripheral devices from METTLER TOLEDO; they are optimally adapted to your balance. 8 Safety Information

9 F F 3 Overview XP-K Comparators Overview XP-K Terminal (details see Operating Instruction Part 2) 2 Display (Touch-sensitive "Touch screen") 3 Operating keys 4 SmartSens sensors 5 Type name 6 Level indicator 7 Centering aid 8 Weighing pan 9 Foot screws 10 Connector for terminal cable 11 RS232C serial interface 12 Socket for AC adapter Overview XP-K Comparators 9

10 4 Installation and Putting into Operation WARNING Risk of electric shock The balance must be disconnected from the power supply before any set-up or installation work, as well as when the housing of the weighing terminal is opened. 4.1 Unpacking and checking the standard equipment Open the packaging and carefully remove all components. 4.2 Scope of delivery Weighing platform RS232C interface Terminal with wall fixture and protective cover Terminal extension cable, length = 5 m AC adapter with country-specific power cable Production certificate CE declaration of conformity Operating instructions part 1 (this document), part 2, part 3 and WeighCom application for XP comparator balances 4.3 Selecting the location and level of the balance Location An optimal location will ensure accurate and reliable operation of the balance. The surface must be able to safely take the weight of the balance when fully loaded. The following local conditions must be observed: Note If the balance is not horizontal at the outset, it must be leveled during commissioning. The balance must only be used indoors and up to a maximum altitude of 4000 m above sea level. Before switching on the balance, wait until all parts are at room temperature (+10 to 30 C). The humidity must be between 10% and 80% non-condensing. The power plug must be accessible at all times. Firm, horizontal and vibration-free location. Avoid direct sunlight. No excessive temperature fluctuations. No strong drafts. Further information can by found in Weighing the Right Way. 10 Overview XP-K Comparators

11 4.3.2 Leveling the balance Note If the balance is not horizontal from the beginning, it will have to be leveled during initial operation. XP155KS, XP604KM, XP1003KM 1 Level the weighing platform by turning the 4 leveling screws (1). 2 Ensure that the leveling screws all sit flat on the floor evenly. 3 Test the stability of the weighing platform by pressing down on or rocking the corners. The level is correct when the air bubble lies in the center of the level indicator (2). 2 1 XP2003KL, XP6002KL 1 Level the weighing platform by turning the 4 leveling screws (1). 2 The leveling screws can be adjusted with a size 30 engineer s wrench. 3 Ensure that the leveling screws all sit flat on the floor evenly. 4 Test the stability of the weighing platform by pressing down on or rocking the corners. The level is correct when the air bubble lies in the center of the level indicator (2) Unblocking and assembling the balance Note Your new balance will be assembled and unblocked by a METTLER TOLEDO service technician Installing the balance cable in the terminal Ensure that a soft, clean surface is used so as not to damage the terminal surface Place the terminal on the operating surface. 2 Open the housing by pressing the 2 buttons (1) for adjusting the terminal and swiveling the housing base upwards. 3 Pull the cable with the retaining ring (2) through the opening on the housing base. 4 Return the terminal to its normal position. 2 Installation and Putting into Operation 11

12 5 Open it so that the cable can be accessed. 6 Insert the cable (3) into the top housing. 7 Close both parts of the housing until the retaining ring (2) is positioned in the cable opening of the housing base. 8 Place the retaining ring (2) behind the two guideways and check that it is secure (tension relief). 9 Before closing the housing, check that the plug is inserted correctly into the terminal plug-in connection. 10 Now close the housing by pressing the two buttons (1) for adjusting the terminal until the housing base engages in the top housing Placing the terminal The terminal can either stand freely or be attached to the wall using a wall fixture. 4.5 Connecting the balance WARNING Risk of electric shock a) To connect the balance, only use the supplied three-core power cord with equipment grounding conductor. b) Only connect the balance to a three-pin power socket with earthing contact. c) Only standardized extension cable with equipment grounding conductor must be used for operation of the balance. d) Intentional disconnection of the equipment grounding conductor is forbidden. The balance is supplied with an AC adapter and country-specific power cable. The AC adapter is suitable for use with the following voltage range: 12 Installation and Putting into Operation

13 V AC, 50/60 Hz. Attention Check whether your local power supply falls within this range. If this is not the case, under no circumstances connect the AC adapter to the power supply, but contact a METTLER TOLEDO representative. The power plug must be accessible at all times. Prior to use, check the power cord for damage. Route the cable in such a way that it cannot be damaged or cause a hindrance when working. Ensure that no liquid comes into contact with the AC adapter. Balance and terminal are at the final location. 1 Connect the AC adapter (1) to the connection socket (2) at the rear of the balance. 2 Connect the AC adapter (1) to the power supply. The balance performs a self-test after connection to the power supply and is then ready to use. 2 1 Note If the display field remains dark, even though the power supply connection functions First disconnect the balance from the power supply. 2 Open the terminal. 3 Press both buttons (3) on the back of the terminal and open the upper part of the terminal. 4 Check that the plug for the terminal cable (4) is connected correctly inside the terminal. 4.6 Setting the reading angle 1 Press in the two buttons (1) on the back of the terminal. The top of the terminal can then be pulled up or pushed down until it engages in the desired position. A total of 3 setting positions are available. 2 Move it in an appropriate position. 1 1 Installation and Putting into Operation 13

14 4.7 Transporting the balance Note If you wish to change the location, please contact your METTLER TOLEDO dealer. 14 Installation and Putting into Operation

15 5 Special Settings for Comparators To fully utilize the high resolution of the balance, some specific rules must be observed. These will enable you to obtain the best possible results. 5.1 Load the balance Because of the high resolution of the balance, even minute differences of temperature or humidity can affect the result. Make sure that the weighing pan are clean and that the weighing sample is acclimatized. CAUTION Use gloves or working aids when loading and unloading the balance Otherwise artifacts may be damaged. Use aids (e.g. crane) with a maximum speed of 5 mm/sec. for loading the balance. A higher speed can have negative influences on the weighing result. 5.2 Settings for the balances AutoZero ProFACT Is switched off at initial operation and after a factory reset (resetting to the factory settings), but can be switched on again when required. When changing over to the "WeighCom" application, AutoZero is automatically switched off. When changing back to the "Weigh" application, the previous status of «AutoZero» is restored. Attention When comparing masses, AutoZero must not be switched on, because it can distort the measurement values. Is switched off at initial operation and after a factory reset (resetting to the factory settings). When comparing masses, it is not advisable to switch ProFACT on. Special Settings for Comparators 15

16 6 Maintenance 6.1 Cleaning Periodically clean the weighing pan, housing and terminal of your balance using a damp cloth. The maintenance interval depends on your standard operating procedure (SOP). Please observe the following notes WARNING Risk of electric shock a) Disconnect the balance from the power supply prior to cleaning and maintenance. b) Only use METTLER TOLEDO power cable, if these need to be replaced. c) Ensure that no liquid comes into contact with the balance, terminal or AC adapter. d) Do not open the balance, terminal or AC adapter. These contain no user-serviceable parts. Cleaning 6.2 Disposal CAUTION Damage of balance On no account use cleaning agents which contain solvents or abrasive ingredients, as this can result in damage to the terminal overlay. Your balance is made from high quality, resistant materials and can therefore be cleaned with a commercially available, mild cleaning agent. Note Please contact your METTLER TOLEDO dealer for details of the available service options. Regular servicing by an authorized service engineer ensures constant accuracy for years to come and prolongs the service life of your balance. In conformance with the European Directive 2002/96/EC on Waste Electrical and Electronic Equipment (WEEE) this device may not be disposed of in domestic waste. This also applies to countries outside the EU, per their specific requirements. Please dispose of this product in accordance with local regulations at the collecting point specified for electrical and electronic equipment. If you have any questions, please contact the responsible authority or the distributor from which you purchased this device. Should this device be passed on to other parties (for private or professional use), the content of this regulation must also be related. Thank you for your contribution to environmental protection. 16 Special Settings for Comparators

17 7 Technical Data 7.1 General data CAUTION Use only with a tested AC Adapter with SELV output current. Ensure correct polarity Power supply AC adapter: Cable for AC adapter: Balance power supply: Primary: V AC, -15%/+10%, 50/60 Hz Secondary: 12 V DC ±3%, 2.5 A (with electronic overload protection) 3-core, with country-specific plug 12 V DC ±3%, 2.25 A, maximum ripple: 80 mvpp Protection and standards Overvoltage category: II Degree of pollution: 2 Protection: IP44, protected against dust and water Standards for safety and EMC: See Declaration of Conformity Range of application: For use only in closed interior rooms Environmental conditions Height above mean sea level: Ambient temperature: Relative air humidity: Maximum air speed: Maximum loading speed: Materials Weighing platform: Terminal: Weighing pan: Up to 4000 m C ±0.7 C / 1 h, or ±1.0 C / 12 h respectively 40 up to 70% ±10% / 4 h 0.20 m/sec 5 mm/sec XP155KS, XP604KM, XP1003KM: Chrome steel X5CrNi18-10, laquered and plastic XP2003KL, XP6002KL: Galvanized steel S235JR+AR, laquered and plastic Die-cast zinc, chromed and plastic Chrome steel X6Cr Explanatory notes for the METTLER TOLEDO AC adapter The certified external power supply which conforms to the requirements for Class II double insulated equipment is not provided with a protective earth connection but with a functional earth connection for EMC purposes. This earth connection IS NOT a safety feature. Further information about conformance of our products can be found in the brochure "Declaration of Conformity" which is coming with each product. In case of testing with regard to the European Directive 2001/95/EC the power supply and the balance have to be handled as Class II double insulated equipment. Consequently an earth bonding test is not required. Similarly it is not necessary to carry out an earth bonding test between the supply earth conductor and any exposed metalwork on the balance. Because the balance are sensitive to static charges a leakage resistor, typically 10 kω, is connected between the earth connector and the power supply output terminals. The arrangement is shown in the equivalent circuit Technical Data 17

18 diagram. This resistor is not part of the electrical safety arrangement and does not require testing at regular intervals. Plastic Housing Double Insulation P AC Input VAC Output 12 VDC N DC 10 kω coupling resistor for electrostatic discharge E Equivalent circuit diagram 7.3 Model-specific data XP155KS XP604KM XP1003KM Limit values Maximum capacity 150 kg 600 kg 1100 kg Readability 0.05 g 0.1 g 0.5 g Tare range (from to) kg kg kg Repeatability (at nominal load) sd 0.15 g (100 kg) 0.3 g (500 kg) 2 g (1000 kg) Repeatability (at low load) sd 0.15 g (5 kg) 0.3 g (20 kg) 2 g (50 kg) Repeatability (at nominal load) (ABA, measured sd 0.12 g (100 kg) 0.23 g (500 kg) 1.5 g (1000 kg) at) 2) Repeatability (at low load) (ABA, measured at) 2) sd 0.09 g (5 kg) 0.15 g (20 kg) 1 g (50 kg) Linearity deviation 2 g 10 g 20 g Eccentricity deviation (test load) 5 g (50 kg) 40 g (200 kg) 40 g (500 kg) Sensitivity offset (test weight) 0.1 g (100 kg) 5 g (500 kg) 10 g (1000 kg) Sensitivity temperature drift 1) %/ C %/ C %/ C Sensitivity stability %/a Rnt %/a %/a Typical values Repeatability (at low load) 2) sd g (100 kg) 0.22 g (500 kg) 1.3 g (1000 kg) Repeatability ABA 2) sd 0.09 g (100 kg) 0.18 g (500 kg) 1 g (1000 kg) Linearity deviation 1.2 g 6 g 12 g Eccentric deviation (test load) 3 g (50 kg) 22 g (200 kg) 22 g (500 kg) Sensitivity offset (test weight) 0.02 g (100 kg) 1 g (500 kg) 2 g (1000 kg) Minimum weight (according to USP) 0.24 kg 0.42 kg 3 kg Minimum weight (U=1%, k=2) kg kg 0.2 kg Settling time 5 s 5 s 5 s Dimensions Balance dimensions (W D H) mm mm mm Weighing pan dimensions mm (W D) mm (W D) Typical uncertainties and supplementary data Repeatability 2) sd 0.08 g % Rgr Repeatability (ABA, measured at) 2) sd 0.06 g % Rgr 0.14 g % Rgr 0.11 g % Rgr mm (W D) 1 g % Rgr 0.6 g % Rgr Differential linearity deviation sd g Rnt 0.06 g Rnt 0.13 g Rnt Differential eccentric load deviation sd 0.006% Rnt 0.011% Rnt % Rnt Sensitivity offset sd % Rnt % Rnt % Rnt Minimum weight (according to USP) 0.24 kg % Rgr 0.42 kg % Rgr 3 kg % Rgr 18 Technical Data

19 XP155KS XP604KM XP1003KM Minimum weight (U=1%, k=2) kg % Rgr kg % Rgr 0.2 kg % Rgr Weighing time 1 ABA 3) s s s Interface update rate 23 /s 23 /s 23 /s Weight of balance 54 kg 93 kg 93 kg Number of built-in reference weights Weights for routine testing OIML CarePac 5 kg M1 20 kg M1 50 kg M1 # # # Weights 100 kg M1 # kg M1 # kg M1 # ASTM CarePac Weights 5 kg ASTM 2 # kg ASTM 2 # kg ASTM 2 # kg ASTM 2 # kg ASTM 2 # kg ASTM 2 # sd = Standard deviation Rnt = Net weight (sample weight) Rgr = Gross weight a = Year (annum) 1) In the temperature range C 2) Value out of 5 ABA measurements according to OIML R111 3) Unloading/Loading: 0 10 kg = 6 s, kg = 15 s, kg = 35 s XP2003KL XP6002KL Limit values Maximum capacity 2500 kg 5400 kg Readability 1 g 10 g Tare range (from to) kg kg Repeatability (at nominal load) sd 10 g (2000 kg) 100 g (5000 kg) Repeatability (at low load) sd 10 g (100 kg) 100 g (200 kg) Repeatability (at nominal load) (ABA, measured sd 7 g (2000 kg) 70 g (5000 kg) at) 2) Repeatability (at low load) (ABA, measured at) 2) sd 4 g (100 kg) 50 g (500 kg) Linearity deviation 100 g 300 g Eccentricity deviation (test load) 120 g (1000 kg) 240 g (2000 kg) Sensitivity offset (test weight) 20 g (2000 kg) 50 g (5000 kg) Sensitivity temperature drift 1) %/ C %/ C Sensitivity stability %/a %/a Typical values Repeatability (at low load) 2) sd 7 g (2000 kg) 70 g (5000 kg) Repeatability ABA 2) sd 5.5 g (2000 kg) 60 g (5000 kg) Linearity deviation 60 g 220 g Eccentric deviation (test load) 33 g (1000 kg) 80 g (2000 kg) Sensitivity offset (test weight) 6 g (2000 kg) 15 g (5000 kg) Minimum weight (according to USP) 12.6 kg 126 kg Minimum weight (U=1%, k=2) 0.84 kg 8.4 kg Settling time 5 s 5 s Dimensions Balance dimensions (W D H) mm Weighing pan dimensions mm (W D) mm mm (W D) Typical uncertainties and supplementary data Repeatability 2) sd 4.2 g % Rgr 42 g % Rgr Repeatability (ABA, measured at) 2) sd 3 g % Rgr 40 g % Rgr Differential linearity deviation sd 1.4 g Rnt 9 g Rnt Differential eccentric load deviation sd % Rnt 0.004% Rnt Technical Data 19

20 XP2003KL XP6002KL Sensitivity offset sd % Rnt % Rnt Minimum weight (according to USP) 12.6 kg % Rgr 126 kg % Rgr Minimum weight (U=1%, k=2) 0.84 kg % Rgr 8.4 kg % Rgr Weighing time 1 ABA 3) s s Interface update rate 23 /s 23 /s Weight of balance 382 kg 382 kg Number of built-in reference weights 2 2 Weights for routine testing OIML CarePac 100 kg M1 200 kg M1 # # Weights 2000 kg M1 # kg M1 # ASTM CarePac Weights 100 kg ASTM 2 # kg ASTM 2 # kg ASTM 2 # kg ASTM 2 #Please inquire sd = Standard deviation Rnt = Net weight (sample weight) Rgr = Gross weight a = Year (annum) 1) In the temperature range C 2) Value out of 5 ABA measurements according to OIML R111 3) Unloading/Loading: 0 10 kg = 6 s, kg = 15 s, kg = 35 s 20 Technical Data

21 7.4 Dimensions Dimensions XP155KS Dimensions in mm FS ø H L L Model: XP155KS FS H L Leveling screw Footprint D Size Height adjustable with 4 leveling screws Min. Max. Level indicator ø 35 mm 17 mm 130 mm 155 mm Technical Data 21

22 7.4.2 Dimensions XP604KM, XP1003KM Dimensions in mm ø H FS FS L Models: XP604KM, XP1003KM FS H L Leveling screw Footprint D Size Height adjustable with 4 leveling screws Min. Max. Level indicator ø 40 mm 19 mm 115 mm 140 mm 22 Technical Data

23 7.4.3 Dimensions XP2003KL, XP6002KL Dimensions in mm H G D L FS Models: XP2003KL, XP6002KL L FS H L Leveling screw Footprint D Size Height adjustable with 4 leveling screws Min. Max. Level indicator mm 30 mm 182 mm 207 mm Technical Data 23

24 7.4.4 Dimensions Terminal Dimensions in mm Terminal 7.5 Interfaces Specifications of RS232C Interface type: Max. cable length: Signal level: Connector: Operating mode: Transmission mode: Transmission code: Baud rates: Bits/parity: Stop bits: Handshake: End-of-line: GND Data Handshake Voltage interface according to EIA RS-232C/DIN (CCITT V24/V.28) 15 m Outputs: Inputs: +5 V V (RL = 3 7 kω) +3 V V 5 V V (RL = 3 7 kω) 3 V V Sub-D, 9-pole, female Full duplex Bit-serial, asynchronous ASCII 600, 1200, 2400, 4800, 9600, 19200, ) (firmware selectable) 7-bit/even, 7-bit/odd, 7-bit/none, 8-bit/none (firmware selectable) 1 stop bit None, XON/XOFF, RTS/CTS (firmware selectable) <CR><LF>, <CR>, <LF> (firmware selectable) Pin 2: Balance transmit line (TxD) Pin 3: Balance receive line (RxD) Pin 5: Ground signal (GND) Pin 7: Clear to send (hardware handshake) (CTS) Pin 8: Request to send (hardware handshake) (RTS) 1) baud is only possible in special cases, such as: Weighing platform without terminal, or Weighing platform with terminal, only via the optional RS232C interface. 24 Technical Data

25 8.003 g g g g g g g g g g g g 8 Accessories and Spare Parts 8.1 Accessories You can increase the functionality of your balance with accessories from the METTLER TOLEDO range. The following options are available: Description Part No. Printers Printer g g g g METTLER TOLEDO BT-P42 printer with Bluetooth connection to instrument Paper roll, set of 5 pcs Paper roll, self-adhesive, set of 3 pcs Ribbon cartridge, black, set of 2 pcs Printer g g g g METTLER TOLEDO RS-P42 printer with RS232C connection to instrument Paper roll, set of 5 pcs Paper roll, self-adhesive, set of 3 pcs Ribbon cartridge, black, set of 2 pcs Cables for RS232C interface RS9 RS9 (m/f): connection cable for PC, length = 1 m RS9 RS25 (m/f): connection cable for PC, length = 2 m Auxiliary displays LC/RS-BLD auxiliary display on bench stand, backlit (incl. RS cable and separate AC adapter) RS/LC-BLDS auxiliary display for table or balance mounting, 480 mm, LCD display with backlighting Accessories and Spare Parts 25

26 LC-AD auxiliary display, active, with table stand LC-ADS auxiliary display, active, with high table stand Terminal IND690, bench model Barcode reader RS232C Barcode Reader The following accessories are needed for operation (not included): RS232 F cable Null modem adapter Plus one of the following: AC adapter 5 V for EU AC adapter 5 V for US AC adapter 5 V for GB AC adapter 5 V for AU RS232C Barcode Reader Cordless The following accessories are needed for operation (not included): Cradle RS232 F cable Null modem adapter Plus one of the following: AC adapter 12 V for EU AC adapter 12 V for US AC adapter 12 V for GB AC adapter 12 V for AU PS/2 Barcode Reader, without cable PS/2 wedge single cable Accessories and Spare Parts

27 PS/2Y Barcode Reader, without cable PS/2 wedge twin (Y) cable Protective covers Protective cover for XP terminal Software MCLink LabX software for one click weighing solutions Enables you to perform One Click Standard Preparation, One Click Loss on Drying, One Click Sieve Analysis and many other applications. Simply start the method with the One Click shortcut on the balance touchscreen. LabX guides you step-by-step through the SOP on the balance, performs your calculations automatically, and takes care of saving all your data. The complete solution can be tailored to match your process requirements. Visit for more information MCLink mass comparator control software MCLink software a simple and practical tool for carrying out your mass measurements to a high level of efficiency. MCLink is the ideal tool for facilities from small calibration laboratories up to scientific mass laboratories Reports are generated safely end efficient with direct control of the comparators with one click. on request Draft shields Draft shield XP-WKS for KS models Draft shield XP-WKM for KM models Draft shield XP-WKL for KL models Accessories and Spare Parts 27

28 LevelMatic LevelMatic 1000 for XP155KS and XP604KM LevelMatic 5000 for XP1003KM, XP2003KL and XP6002KL Reference weights Reference weight, 100 kg (E1), certified Please inquire Reference weight, 200 kg (E1), certified Please inquire Reference weight, 500 kg (E1), certified Please inquire Reference weight, 1000 kg (E1), certified Please inquire Reference weight, 2000 kg (E2), certified Please inquire Reference weight, 5000 kg (E2), certified Please inquire 28 Accessories and Spare Parts

29 Various AC/DC adapter (without power cable) V AC, 0.8 A, 50/60 Hz, 12 V DC 2.5 A Country-specific 3-Pin power cable with grounding conductor. Power cable AU Power cable BR Power cable CH Power cable CN Power cable DK Power cable EU Power cable GB Power cable IL Power cable IN Power cable IT Power cable JP Power cable TH, PE Power cable US Power cable ZA Spare parts Pos Description Part No. XP Terminal complete with firmware F METTLER TOLEDO F Accessories and Spare Parts 29

30 9 Appendix 9.1 MT-SICS interface commands and functions Many of the instruments and balances used have to be capable of integration in a complex computer or data acquisition system. To enable you to integrate balances in your system in a simple manner and utilize their capabilities to the full, most balance functions are also available as appropriate commands via the data interface. All new METTLER TOLEDO balances launched on the market support the standardized command set "METTLER TOLEDO Standard Interface Command Set" (MT-SICS). The commands available depending on the functionality of the balance. For further information please refer to the Reference Manual MT-SICS downloadable from the Internet under u 30 Accessories and Spare Parts

31 Index A B AC adapter 13, 17, 17 Accessories 25 Balance cable 11 T Setting the reading angle 13 Settings 15 Staff safety 8 Technical data 17 Terminal 11 C Cleaning 16 Connecting the balance 13 Connecting to power supply 13 Conventions 6 D Dimensions 21 Display field remains dark 13 Disposal 16 E Environmental conditions 17 F Features 5 G General safety information 7 GLP 5 Good Laboratory Practice 5 I Interface MT-SICS 30 ISO ISO L Load the balance 15 Local conditions 10 Location 10 M Materials 17 MT-SICS 30 P Power cable 12 Power supply 17 Power supply voltage 12 Protection and standards 17 R RS232C interface 24 S Safety information 7, 7 Staff safety 8 Self-test 13 Index 31

32

33

34 For more information Mettler-Toledo AG, Laboratory Weighing CH-8606 Greifensee, Switzerland Tel. +41 (0) Fax +41 (0) Subject to technical changes. Mettler-Toledo AG 01/ B en * *